ANALOG DIODE PHASE SHIFTERS CONTINUOUSLY VARIABLE 0.1-18 GHz GENERAL INFORMATION An analog phase shifter continuously changes the phase of a microwave signal by varying a D.C. voltage. Since the D.C. voltage applied to the diode is a reverse bias, the current drain is negligible (typically less than 10 microamps). A balanced stripline configuration keeps the VSWR and amplitude ripple to a minimum for all values of phase. GENERAL SPECIFICATIONS Frequency Coverage: 0.1 to 18.0 GHz RF impedance: 50 OHMS. D.C. Voltage: 0 volts to +28 volts (standard), or O volts to 28 volts (optional) will vary the phase of any of the models over the minimum phase shift listed RF Power: 10 mW peak or CW, operating. Destruct level is 1 W, CW, 100 W peak. Temperature Information: The units can be used over a 55C to +85C temperature range. However, the phase will change either +5 or +5%, whichever is greater. If temperature com- pensation is required, this can be done on request. With compensation, the variation can be held to +1 or +1%, whichever is greater, from 55C to +85C. The size remains the same. If compensation is desired, add a suffix T to the model num- ber (e.g., PQ-17T). Series PQ phase shifters can be driven from any phase value to any other value in 10 nanoseconds. With linearizers, the response time is 50 nanoseconds. With temperature compensation the response time is 100 nanoseconds. Switching Speed: Connectors: SMA Notes: 1. LINEARIZATION: For phase shifters with linearizers add a suffix L to the model number (e.g., PQ-23L). Linearity is +2.0 for phase shifters for 150 or less, and +4 for phase shifters between 150 and 360. With linearization, DC voltages of +15V at +30mA are required. The control voltage is 0-10 volts. A control voltage of 0-5 volts can be supplied at no additional cost, by adding a suffix 5 to the model number (e.g. PQ-23L5). Linearity is measured at fo. 2. PHASE FLATNESS: The phase shift varies with frequency at any voltage setting. This variation, referenced to 0 at 0 volts for each frequency, is approximately +15% for octave models, + 10% for models with 25% bandwidth, and +7.5% for models with a 10% bandwidth. 3. Aconnector, (SMA Female) is available in place of the bias pin at no extra charge. This will be placed at the center of the surface marked F on the drawing. This is the 0.38 x A surface. If a SMA Female is desired, add suffix C to the model number (e.g., PQ- 23C). 4. Monotonicity guaranteed for all models. SERIES PQ 150 T T T T T 1.0 4 |,t if 120 a 5 a Ww LL. - w a 9 INSERTION 7 G E LOSS > x 9 = 60b ae y i PHASE J.2 = 30h (SAE 22 | L L L L L 0 0 5 10 15 20 25 30 VOLTAGE (VY Fig. 1 Typical Phase & Insertion Loss vs. Voltage Curves for PQ-31 PHASE SHIFT S (DEG) | 0.4 1.0 1 BIAS VOLTAGE VB (V) Fig. 2 Phase shift characteristic of PQ-45. . 7 CANSRAB esa at 1 0/98 180 9001 REGISTERED FIRM An MCE Co Se 60 South Jefferson Road, Whippany, NJ 07981 = TR I A N G L E Tel: 973-887-8100 * Fax: 973-884-0445 "ORPORATION E-Mail: kdisales@aol.com See us on the web @ www.kditriangle.comANALOG DIODE PHASE SHIFTERS CONTINUOUSLY VARIABLE 0.1-18 GHz SERIES PQ 7 SURFACE [RR E 0.25[6,3] CV. = +15V 0 -15V GND 0.25(6,3} K-crone gem ft al GROUND BIAS PIN t| ] J J NE je a rTt SMA | SMA | FEMALE FEMALE TYP. DB \ DB Ie di pe! tw tat | 0.40 | | 0.1012.5] = F 01925) [* c > | F [10,2] TYP. 0.3849,71 TYP. A 0.3849,71 aoe Beas 3 nN 3 MOUNTING HOLE! HOLES OUTLINE WITHOUT LINEARIZER OUTLINE WITH LINEARIZER ELECTRICAL PERFORMANCE MECHANICAL OUTLINES Phase A B C D E F Shift Insertion Amplitude Out- in in in in in in Note 2 Loss Ripple Outline line [mm] [mm] [mm] [mm] [mm] [mm] Frequency Minimum Maximum Maximum VSWR No With 275 2.95 138 2050 2250 053 Model No.* Range GHz Degrees dp + dB Maximum Linearizer _Linearizer 1 [69,91] [57,15] [35,05] [52,07] [57,15] [13,46] aa 7 = * = 125 200 063-1800 0750 025 _ : : : [31,75] [50,8] [16,0] [45,7] [19,1] [6,4] a =a = = of 1 ; 1 ; 3 5.00 2.00 NA 1.800 4500 0.25 - - - [127,0] [50,8] 4holes [45,7] [1143] [6,4] aa a on ~ = ae : : , 718 250 WA 2300 7.250 025 - - - - - [196,8] [63,5] 4holes [58,42] [184,15] [6,4] aH = oa i ae = - : 5 650 2.00 NA 1.800 6000 0.25 ___ - - - [165.1] [50,8] 4holes [45,7] [152,4] [6,4] aa - = * = : ; 5 200 200 100 1800 1500 025 _* : : : [50,8] [50,8] [25,4] [45,7] [38,1] [6,4] aa ae =a a = = ; ; ; 300 200 150 1800 2500 025 _ : : : [76,2] [50,8] [38,1] [45,7] [63,5] [6,4] aa ae a = = - - ; 3 650 2.50 NA 2300 6000 0.25 __ - - - [165.1] [63,5] 4holes [58,42] [152,4] [6,4] aa 4 = > = = : : 9 000 200 WA 1800 4500 0.50 - - - - - [127,0] [50,8] 4holes [45,7] [1143] [12,7] ae om = a = : ; 718250 WA 2300 7.250 076 - - - - - [196,8] [63,5] 4holes [58,42] [184,15] [19,1] PQ-74 8.0-18.0 360 17.0 3.5 2.50 9 9 PQ-94 16.0-17.0 50 2.0 0.20 1.65 2 6 *OPTIONS: (Add to Model No.) T = Temp. Comp. L Linearization C = Bias Connector SMA 5 = Oto 5 Volts Control Voltage for Linearized Models. Tel: 973-887-8100 Fax: 973-884-0445 E-Mail: kdisales@aol.com See us on the web @ www.kditriangle.com RIANGLE ORPORATION CAVE An MCE Company IT } (S0 9001 REGISTERED FIRM 60 South Jefferson Road, Whippany, NJ 07981 10/98