a CMOS 300 MHz Quadrature Complete-DDS AD9854 FEATURES 300 MHz Internal Clock Rate Integrated 12-Bit Output DAC Ultrahigh-Speed, 3 ps RMS Jitter Comparator Excellent Dynamic Performance: 80 dB SFDR @ 100 MHz (1 MHz) AOUT 4 to 20 Programmable Reference Clock Multiplier Dual 48-Bit Programmable Frequency Registers Dual 14-Bit Programmable Phase Offset Registers 12-Bit Amplitude Modulation and Programmable Shaped On/Off Keying Function Single Pin FSK and PSK Data Interface Linear or Nonlinear FM Chirp Functions with Single Pin Frequency "Hold" Function Frequency-Ramped FSK <25 ps RMS Total Jitter in Clock Generator Mode Automatic Bidirectional Frequency Sweeping SIN(x)/x Correction Simplified Control Interface 10 MHz Serial, 2-Wire or 3-Wire SPI-Compatible or 100 MHz Parallel 8-Bit Programming 3.3 V Single Supply Multiple Power-Down Functions Single-Ended or Differential Input Reference Clock Small 80-Lead LQFP Packaging APPLICATIONS Agile, Quadrature L.O. Frequency Synthesis Programmable Clock Generator FM Chirp Source for Radar and Scanning Systems Test and Measurement Equipment Commercial and Amateur RF Exciter GENERAL DESCRIPTION The AD9854 digital synthesizer is a highly integrated device that uses advanced DDS technology, coupled with two internal high-speed, high-performance quadrature D/A converters and a comparator to form a digitally-programmable I and Q synthesizer function. When referenced to an accurate clock source, the AD9854 generates highly stable, frequency-phase-amplitudeprogrammable sine and cosine outputs that can be used as an agile L.O. in communications, radar, and many other applications. The AD9854's innovative high-speed DDS core provides 48-bit frequency resolution (1 microHertz tuning steps). Phase truncation to 17 bits assures excellent SFDR. The AD9854's circuit (continued on page 14) FUNCTIONAL BLOCK DIAGRAM DAC RSET PHASE ACCUMULATOR FREQUENCY ACCUMULATOR REFERENCE CLOCK IN 43-203 REF CLK MULTIPLEXER PHASE/OFFSET MODULATION SYSTEM CLOCK FSK/BPSK/HOLD DATA IN DIGITAL MULTIPLIERS DDS SINE-TO-AMPLITUDE CONVERTER 300MHz DIFF/SINGLE SELECT I INV. SINC FILTER Q INV. SINC FILTER RAMP-UP/-DOWN CLOCK/LOGIC AND MULTIPLEXER FREQUENCY TUNING WORD/PHASE WORD MULTIPLEXER AND RAMP START STOP LOGIC 48-BIT FREQUENCY TUNING WORD BIDIRECTIONAL I/O UPDATE 14-BIT PHASE OFFSET/ MODULATION MUX AD9854 12-BIT "I" DAC ANALOG OUT 12-BIT "Q" OR CONTROL DAC ANALOG OUT SHAPED ON/OFF KEYING 12-BIT CONTROL DAC DATA 12-BIT AM MOD ANALOG IN PROGRAMMING REGISTERS READ CLOCK OUT PROGRAMMABLE RATE AND UPDATE CLOCKS I/O PORT BUFFERS WRITE COMPARATOR SERIAL/PARALLEL SELECT 6-BIT ADDRESS OR SERIAL PROGRAMMING LINES 8-BIT PARALLEL LOAD MASTER RESET +VS GND REV. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 1999 (V = 3.3 V 5%, R = 3.9 k external reference clock frequency = 30 MHz with AD9854-SPECIFICATIONS REFCLK Multiplier enabled at 10 for AD9854ASQ, external reference clock frequency = 20 MHz with REFCLK Multiplier enabled at 10 for S SET AD9854AST unless otherwise noted.) Parameter Temp Test Level Min AD9854ASQ Typ Max FULL VI 5 300 5 200 MHz 75 300 55 5 5 45 50 200 55 MHz MHz % pF k 1.9 800 1.6 2.3 Min AD9854AST Typ Max Unit REF CLOCK INPUT CHARACTERISTICS1 Internal Clock Frequency Range External REF Clock Frequency Range REFCLK Multiplier Enabled REFCLK Multiplier Disabled Duty Cycle Input Capacitance Input Impedance Differential Mode Common-Mode Voltage Range Minimum Signal Amplitude Common-Mode Range VIH (Single-Ended Mode) VIL (Single-Ended Mode) FULL FULL 25C 25C 25C VI VI IV IV IV 5 5 45 25C 25C 25C 25C IV IV IV IV 800 1.6 2.3 DAC STATIC OUTPUT CHARACTERISTICS Output Update Speed Resolution I and Q Full-Scale Output Current I and Q DAC DC Gain Imbalance2 Gain Error Output Offset Differential Nonlinearity Integral Nonlinearity Output Impedance Voltage Compliance Range FULL 25C 25C 25C 25C 25C 25C 25C 25C 25C I IV IV I I I I I IV I 25C IV 0.2 25C 25C 25C 25C 25C 25C V V V V V V 58 56 52 48 48 48 58 56 52 48 48 dBc dBc dBc dBc dBc dBc 25C 25C 25C 25C 25C 25C 25C 25C 25C V V V V V V V V V 83 83 91 82 84 89 71 77 83 83 83 91 82 84 89 dBc dBc dBc dBc dBc dBc dBc dBc dBc 25C 25C 25C V V V 140 138 142 140 138 142 dBc/Hz dBc/Hz dBc/Hz 25C 25C 25C V V V 142 148 152 142 148 152 dBc/Hz dBc/Hz dBc/Hz 25C 25C 25C IV IV IV 17 12 10 17 12 10 SysClk Cycles SysClk Cycles SysClk Cycles DAC DYNAMIC OUTPUT CHARACTERISTICS I and Q DAC Quad. Phase Error DAC Wideband SFDR 1 MHz to 20 MHz AOUT 20 MHz to 40 MHz AOUT 40 MHz to 60 MHz AOUT 60 MHz to 80 MHz AOUT 80 MHz to 100 MHz AOUT 100 MHz to 120 MHz AOUT DAC Narrowband SFDR 10 MHz AOUT ( 1 MHz) 10 MHz AOUT ( 250 kHz) 10 MHz AOUT ( 50 kHz) 41 MHz AOUT ( 1 MHz) 41 MHz AOUT ( 250 kHz) 41 MHz AOUT ( 50 kHz) 119 MHz AOUT ( 1 MHz) 119 MHz AOUT ( 250 kHz) 119 MHz AOUT ( 50 kHz) Residual Phase Noise (AOUT = 5 MHz, Ext. CLK = 30 MHz, REFCLK Multiplier Engaged at 10x) 1 kHz Offset 10 kHz Offset 100 kHz Offset (AOUT = 5 MHz, Ext. CLK = 300 MHz, REFCLK Multiplier Bypassed) 1 kHz Offset 10 kHz Offset 100 kHz Offset Pipeline Delays Phase Accumulator and DDS Core Inverse Sinc Filter Digital Multiplier 50 3 100 1.75 50 3 100 1.75 1 1 300 5 -0.5 -6 12 10 +0.15 0.3 0.6 100 -0.5 -2- 200 20 +0.5 +2.25 2 1.25 1.66 5 -0.5 -6 +1.0 -0.5 1 1.9 12 10 +0.15 0.3 0.6 100 0.2 mV p-p V V V +1.0 MSPS Bits mA dB % FS A LSB LSB k V 1 Degrees 20 +0.5 +2.25 2 1.25 1.66 REV. 0 AD9854 Parameter Temp Test Level Min AD9854ASQ Typ Max MASTER RESET DURATION 25C IV 10 COMPARATOR INPUT CHARACTERISTICS Input Capacitance Input Resistance Input Current Hysteresis 25C 25C 25C 25C V IV I IV COMPARATOR OUTPUT CHARACTERISTICS Logic "1" Voltage, High Z Load Logic "0" Voltage, High Z Load Output Power, 50 Load, 120 MHz Toggle Rate Propagation Delay Output Duty Cycle Error3 Rise/Fall Time, 5 pF Load Toggle Rate, High Z Load Toggle Rate, 50 Load Output Cycle-to-Cycle Jitter4 FULL FULL 25C 25C 25C 25C 25C 25C 25C VI VI I IV I V IV IV IV COMPARATOR NARROWBAND SFDR 10 MHz ( 1 MHz) 10 MHz ( 250 kHz) 10 MHz ( 50 kHz) 41 MHz ( 1 MHz) 41 MHz ( 250 kHz) 41 MHz ( 50 kHz) 119 MHz ( 1 MHz) 119 MHz ( 250 kHz) 119 MHz ( 50 kHz) 25C 25C 25C 25C 25C 25C 25C 25C 25C V V V V V V V V V 84 84 92 76 82 89 73 73 83 84 84 92 76 82 89 73 73 83 dBc dBc dBc dBc dBc dBc dBc dBc dBc CLOCK GENERATOR OUTPUT JITTER5 5 MHz AOUT 40 MHz AOUT 100 MHz AOUT 25C 25C 25C V V V 23 12 7 23 12 7 ps rms ps rms ps rms PARALLEL I/O TIMING CHARACTERISTICS TASU (Address Setup Time to WR Signal Active) TADHW (Address Hold Time to WR Signal Inactive) TDSU (Data Setup Time to WR Signal Inactive) TDHD (Data Hold Time to WR Signal Inactive) TWRLOW (WR Signal Minimum Low Time) TWRHIGH (WR Signal Minimum High Time) TWR (WR Signal Minimum Period) TADV (Address to Data Valid Time) TADHR (Address Hold Time to RD Signal Inactive) TRDLOV (RD Low-to-Output Valid) TRDHOZ (RD High-to-Data Three-State) FULL FULL FULL FULL FULL FULL FULL FULL FULL FULL FULL IV IV IV IV IV IV IV V IV IV IV 8.2 0 2.1 0 2.2 7 10 15 5 7.8 ns ns ns ns ns ns ns ns ns ns ns SERIAL I/O TIMING CHARACTERISTICS TPRE (CS Setup Time) TSCLK (Period of Serial Data Clock) TDSU (Serial Data Setup Time) TSCLKPWH (Serial Data Clock Pulsewidth High) TSCLKPWL (Serial Data Clock Pulsewidth Low) TDHLD (Serial Data Hold Time) TDV (Data Valid Time) FULL FULL FULL FULL FULL FULL FULL IV IV IV IV IV IV V 30 100 30 40 40 0 CMOS LOGIC INPUTS Logic "1" Voltage Logic "0" Voltage Logic "1" Current Logic "0" Current Input Capacitance 25C 25C 25C 25C 25C I I IV IV V 2.7 Min AD9854AST Typ Max 10 3 500 1 10 3.1 SysClk Cycles 3 500 1 10 5 20 -10 300 375 5 20 3.1 0.16 9 11 3 1 2 350 400 0.16 9 +10 -10 300 375 Unit 11 3 1 2 350 400 4.0 +10 4.0 pF k A mV p-p V V dBm ns % ns MHz MHz ps rms 4 REV. 0 7.8 1.6 1.8 15 8.2 0 2.1 0 2.2 7 10 15 5 1.6 1.8 15 15 10 15 10 30 100 30 40 40 0 30 30 2.7 0.4 5 5 3 -3- ns ns ns ns ns ns ns 0.4 12 12 3 V V A A pF AD9854-SPECIFICATIONS Parameter Temp Test Level 25C 25C 25C 25C 25C 25C 25C I I I I I I I Min AD9854ASQ Typ Max Min AD9854AST Typ Max Unit 6 POWER SUPPLY +VS Current7 +VS Current8 +VS Current9 P DISS7 P DISS8 P DISS9 P DISS Power-Down Mode 1050 710 600 3.475 2.345 1.975 1 1210 816 685 4.190 2.825 2.375 50 755 515 435 2.490 1.700 1.435 1 865 585 495 3.000 2.025 1.715 50 mA mA mA W W W mW NOTES 1 The reference clock inputs are configured to accept a 1 V p-p (minimum) dc offset sine wave centered at one-half the applied V DD or a 3 V TTL-level pulse input. 2 The I and Q gain imbalance is digitally adjustable to less than 0.01 dB. 3 Change in duty cycle from 1 MHz to 100 MHz with 1 V p-p sine wave input and 0.5 V threshold. 4 Represents comparator's inherent cycle-to-cycle jitter contribution. Input signal is a 1 V, 40 MHz square wave. Measurement device Wavecrest DTS - 2075. 5 Comparator input originates from analog output section via external 7-pole elliptic LPF. Single-ended input, 0.5 V p-p. Comparator output terminated in 50 . 6 Simultaneous operation at the maximum ambient temperature of 85 C and the maximum internal clock frequency of 200 MHz for the 80-lead LQFP, or 300 MHz for the thermally-enhanced 80-lead LQFP may cause the maximum die junction temperature of 150 C to be exceeded. Refer to the section titled Power Dissipation and Thermal Considerations for derating and thermal management information. 7 All functions engaged. 8 All functions except inverse sinc engaged. 9 All functions except inverse sinc and digital multipliers engaged. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS* EXPLANATION OF TEST LEVELS Test Level Maximum Junction Temperature . . . . . . . . . . . . . . . . 150C VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 V Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . -0.7 V to +VS Digital Output Current . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA Storage Temperature . . . . . . . . . . . . . . . . . . -65C to +150C Operating Temperature . . . . . . . . . . . . . . . . . -40C to +85C Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . 300C Maximum Clock Frequency . . . . . . . . . . . . . . . . . . 300 MHz I - 100% Production Tested. III - Sample Tested Only. IV - Parameter is guaranteed by design and characterization testing. V - Parameter is a typical value only. VI - Devices are 100% production tested at 25C and guaranteed by design and characterization testing for industrial operating temperature range. *Absolute maximum ratings are limiting values, to be applied individually, and beyond which the serviceability of the circuit may be impaired. Functional operability under any of these conditions is not necessarily implied. Exposure of absolute maximum rating conditions for extended periods of time may affect device reliability. ORDERING GUIDE Model Temperature Range Package Description Package Option AD9854ASQ AD9854AST AD9854/PCB -40C to +85C -40C to +85C 0C to 70C Thermally-Enhanced 80-Lead LQFP 80-Lead LQFP Evaluation Board SQ-80 ST-80 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD9854 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. -4- WARNING! ESD SENSITIVE DEVICE REV. 0 AD9854 PIN FUNCTION DESCRIPTIONS Pin No. Pin Name Function 1-8 9, 10, 23, 24, 25, 73, 74, 79, 80 11, 12, 26, 27, 28, 72, 75, 76, 77, 78 13, 35, 57, 58, 63 14-19 D7-D0 DVDD Eight-Bit Bidirectional Parallel Programming Data Inputs. Used only in parallel programming mode. Connections for the Digital Circuitry Supply Voltage. Nominally 3.3 V more positive than AGND and DGND. DGND Connections for Digital Circuitry Ground Return. Same potential as AGND. NC No Internal Connection. A5-A0 (17) A2/IO RESET (18) (19) 20 A1/SDO A0/SDIO I/O UD 21 WRB/SCLK 22 RDB/CSB 29 FSK/BPSK/ HOLD 30 SHAPED KEYING 31, 32, 37, 38, 44, 50, 54, 60, 65 33, 34, 39, 40, 41, 45, 46, 47, 53, 59, 62, 66, 67 36 AVDD Six-Bit Parallel Address Inputs for Program Registers. Used only in parallel programming mode. A0, A1, and A2 have a second function when the serial programming mode is selected. See immediately below. Allows a RESET of the serial communications bus that is unresponsive due to improper programming protocol. Resetting the serial bus in this manner does not affect previous programming nor does it invoke the "default" programming values seen in the Table V. Active HIGH. Unidirectional Serial Data Output for Use in 3-Wire Serial Communication Mode. Bidirectional Serial Data Input/Output for Use in 2-Wire Serial Communication Mode. Bidirectional Frequency Update Signal. Direction is selected in control register. If selected as an input, a rising edge will transfer the contents of the programming registers to the internal works of the IC for processing. If I/O UD is selected as an output, an output pulse (low to high) of eight system clock cycle duration indicates that an internal frequency update has occurred. Write Parallel Data to Programming Registers. Shared function with SCLK. Serial clock signal associated with the serial programming bus. Data is registered on the rising edge. This pin is shared with WRB when the parallel mode is selected. Read Parallel Data from Programming Registers. Shared function with CSB. Chip-select signal associated with the serial programming bus. Active LOW. This pin is shared with RDB when the parallel mode is selected. Multifunction Pin According to the Mode of Operation Selected in the Programming Control Register. If in the FSK mode logic low selects F1, logic high selects F2. If in the BPSK mode, logic low selects Phase 1, logic high selects Phase 2. If in the Chirp mode, logic high engages the HOLD function causing the frequency accumulator to halt at its current location. To resume or commence Chirp, logic low is asserted. Must First Be Selected in the Programming Control Register to Function. A logic high will cause the I and Q DAC outputs to ramp-up from zero-scale to full-scale amplitude at a preprogrammed rate. Logic low causes the full-scale output to ramp-down to zero-scale at the preprogrammed rate. Connections for the Analog Circuitry Supply Voltage. Nominally 3.3 V more positive than AGND and DGND 42 43 48 49 51 52 REV. 0 AGND Connections for Analog Circuitry Ground Return. Same potential as DGND. VOUT Internal High-Speed Comparator's Noninverted Output Pin. Designed to drive 10 dBm to 50 load as well as standard CMOS logic levels. Voltage Input Positive. The internal high-speed comparator's noninverting input. Voltage Input Negative. The internal high-speed comparator's inverting input. Unipolar Current Output of the I or Cosine DAC. Complementary Unipolar Current Output of the I or Cosine DAC. Complementary Unipolar Current Output of the Q or Sine or DAC. Unipolar Current Output of the Q or Sine DAC. This DAC can be programmed to accept external 12-bit data in lieu of internal sine data. This allows the AD9854 to emulate the AD9852 control DAC function. VINP VINN IOUT1 IOUT1B IOUT2B IOUT2 -5- AD9854 Pin No. Pin Name Function 55 DACBP 56 DAC RSET 61 PLL FILTER 64 DIFF CLK ENABLE 68 REFCLKB 69 REFCLK 70 S/P SELECT 71 MASTER RESET Common Bypass Capacitor Connection for Both I and Q DACs. A 0.01 F chip cap from this pin to AVDD improves harmonic distortion and SFDR slightly. No connect is permissible (slight SFDR degradation). Common Connection for Both I and Q DACs to Set the Full-Scale Output Current. RSET = 39.9/IOUT. Normal RSET range is from 8 k (5 mA) to 2 k (20 mA). This pin provides the connection for the external zero compensation network of the REFCLK Multiplier's PLL loop filter. The zero compensation network consists of a 1.3 k resistor in series with a 0.01 F capacitor. The other side of the network should be connected to AVDD as close as possible to Pin 60. For optimum phase noise performance, the REFCLK Multiplier can be bypassed by setting the "Bypass PLL" bit in control register 1E. Differential REFCLK Enable. A high level of this pin enables the differential clock inputs, REFCLK and REFCLKB (Pins 69 and 68 respectively). The minimum differential signal amplitude required is 800 mV p-p. The centerpoint or common-mode range of the differential signal ranges from 1.6 V to 1.9 V. The Complementary (180 Degrees Out-of-Phase) Differential Clock Signal. User should tie this pin high or low when single-ended clock mode is selected. Same signal levels as REFCLK. Single-Ended Reference Clock Input or One of Two Differential Clock Signals. Normal 3.3 V CMOS logic levels or 1 V p-p sine wave centered about 1.6 V. Selects Between Serial Programming Mode (Logic LOW) and Parallel Programming Mode (Logic High). Initializes the serial/parallel programming bus to prepare for user programming; sets programming registers to a "do-nothing" state defined by the default values seen in the Table V. Active on logic high. Asserting MASTER RESET is essential for proper operation upon power-up. -6- REV. 0 AD9854 DVDD DVDD DGND DGND DGND DGND DVDD DVDD DGND MASTER RESET S/P SELECT REFCLOCK REFCLOCKB AGND AGND AVDD DIFF CLK ENABLE NC AGND PLL FILTER PIN CONFIGURATION 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 AVDD 59 AGND D5 3 58 NC D4 4 57 NC D3 5 56 DAC RSET D2 6 55 DACBP D1 7 54 AVDD D0 8 53 AGND DVDD 9 52 IOUT2 51 IOUT2B 50 AVDD 49 IOUT1B NC 13 48 IOUT1 A5 14 47 AGND A4 15 46 AGND A3 16 45 AGND A2/IO RESET 17 44 AVDD A1/SDO 18 43 VINN A0/SDIO 19 42 VINP I/O UD 20 40 AGND D7 1 D6 2 PIN 1 IDENTIFIER AD9854 DVDD 10 TOP VIEW (Not to Scale) 80-LEAD LQFP 14 3 14 3 1.4 DGND 11 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 WRB/SCLK RDB/CSB DVDD DVDD DVDD DGND DGND DGND FSK/BPSK/HOLD SHAPED KEYING AVDD AVDD AGND AGND NC VOUT AVDD AVDD AGND AGND DGND 12 NC = NO CONNECT VDD VDD DIGITAL OUT IOUT VINP/ VINN DIGITAL IN IOUTB a. DAC Outputs b. Comparator Output c. Comparator Input Figure 1. Equivalent Input and Output Circuits REV. 0 VDD VDD -7- d. Digital Input AD9854 Figures 2-7 indicate the wideband harmonic distortion performance of the AD9854 from 19.1 MHz to 119.1 MHz Fundamental Output, Reference Clock = 30 MHz, REFCLK Multiplier = 10. Each graph plotted from 0 MHz to 150 MHz. 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 START 0Hz 15MHz/ START 0Hz STOP 150MHz Figure 2. Wideband SFDR, 19.1 MHz 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 15MHz/ STOP 150MHz Figure 5. Wideband SFDR, 79.1 MHz 0 START 0Hz 15MHz/ STOP 150MHz START 0Hz Figure 3. Wideband SFDR, 39.1 MHz 15MHz/ STOP 150MHz Figure 6. Wideband SFDR, 99.1 MHz 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 START 0Hz 15MHz/ STOP 150MHz START 0Hz Figure 4. Wideband SFDR, 59.1 MHz 15MHz/ STOP 150MHz Figure 7. Wideband SFDR, 119.1 MHz -8- REV. 0 AD9854 Figures 8-11 show the trade-off in elevated noise floor, increased phase noise, and occasional discrete spurious energy when the internal REFCLK Multiplier circuit is engaged. Plots with wide (1 MHz) and narrow (50 kHz) spans are shown. 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 CENTER 39.1MHz 100kHz/ CENTER 39.1MHz SPAN 1MHz Figure 8. Narrowband SFDR, 39.1 MHz, 1 MHz BW, 300 MHz EXTCLK with REFCLK Multiply Bypassed 100kHz/ SPAN 1MHz Figure 10. Narrowband SFDR, 39.1 MHz, 1 MHz BW, 30 MHz EXTCLK with REFCLK Multiply = 10x 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 CENTER 39.1MHz 5kHz/ SPAN 50kHz CENTER 39.1MHz Figure 9. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 300 MHz EXTCLK with REFCLK Multiplier Bypassed 5kHz/ SPAN 50kHz Figure 11. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 30 MHz EXTCLK/REFCLK Multiplier = 10x Figures 12 and 13 show the slight increase in noise floor both with and without the PLL when slower clock speeds are used to generate the same fundamental frequency, that is, with a 100 MHz clock as opposed to a 300 MHz clock in Figures 10 and 12. 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 CENTER 39.1MHz 5kHz/ SPAN 50kHz CENTER 39.1MHz Figure 12. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 100 MHz EXTCLK with REFCLK Multiplier Bypassed REV. 0 5kHz/ SPAN 50kHz Figure 13. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 10 MHz EXTCLK with REFCLK Multiplier = 10x -9- AD9854 Figures 14 and 15 show the effects of utilizing "sweet spots" in the tuning range of a DDS. Figure 14 represents a tuning word that accentuates the aberrations associated with truncation in the DDS algorithm. Figure 16 is essentially the same output frequency (a few tuning codes over), but it displays much fewer spurs on the output due to the selection of a tuning "sweet spot." Consideration should be given to all DDS applications to exploit the benefit of sweet spot tuning. 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 CENTER 112.499MHz 50kHz/ SPAN 500kHz CENTER 112.469MHz Figure 14. The Opposite of a "Sweet Spot." 112.469 MHz with multiple high energy spurs close around the fundamental. 50kHz/ SPAN 500kHz Figure 15. A slight change in tuning word yields dramatically better results. 112.499 MHz with all spurs shifted out-of-band. Figures 16 and 17 show the narrowband performance of the AD9854 when operating with a 20 MHz reference clock and the REFCLK Multiplier enabled at 10x vs. a 200 MHz external reference clock. 0 0 -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -60 -70 -70 -80 -80 -90 -90 -100 -100 CENTER 39.1MHz 5kHz/ CENTER 39.1MHz SPAN 50kHz 5kHz/ SPAN 50kHz Figure 17. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 10 MHz EXTCLK with REFCLK Multiplier = 10x Figure 16. Narrowband SFDR, 39.1 MHz, 50 kHz BW, 200 MHz EXTCLK with REFCLK Multiplier Bypassed -10- REV. 0 AD9854 -110 -110 -115 -115 -120 -120 PHASE NOISE - dBc/Hz PHASE NOISE - dBc/Hz 80MHz -125 -130 80MHz -135 -140 5MHz -145 -125 -130 -135 5MHz -140 -145 -150 -150 -155 100 1k 10k FREQUENCY - Hz -155 100 100k 1k 10k FREQUENCY - Hz 100k b. Residual Phase Noise, 300 MHz (10x REFCLK Multiplier Enabled) Figure 18. Residual Phase Noise (5.2 MHz A OUT), REFCLK Multiplier Disabled, EXTCLK = 300 MHz a. Residual Phase Noise, 300 MHz Direct Clocking 55 54 SFDR - dBc 53 RISE TIME 1.04ns 52 JITTER [10.6ps RMS] 51 50 49 48 -33ps 0 5 10 15 DAC CURRENT - mA 20 500ps/DIV 25 Figure 19. SFDR vs. DAC Current, 59.1 AOUT, 300 MHz EXTCLK 232mV/DIV 0ps +33ps 50V INPUT Figure 21. Typical Comparator Output Jitter, 40 MHz A OUT, 300 MHz EXTCLK/REFCLK Multiplier Disabled SUPPLY CURRENT - mA 620 615 REF1 RISE 1.174ns 610 C1 FALL 1.286ns 605 600 595 590 0 20 40 60 80 100 FREQUENCY - MHz 120 CH1 140 Figure 20. Supply Current vs. Output Frequency; Variation Is Minimal as a Percentage and Heavily Dependent on Tuning Word REV. 0 500mVV M 500ps CH1 980mV Figure 22. Comparator Rise/Fall Times -11- AD9854 LPF 1200 LPF RF/IF INPUT SIN AD9854 LPF REFCLK COS I BASEBAND CHANNEL SELECT FILTERS 1000 AMPLITUDE - mV p-p LPF MINIMUM COMPARATOR INPUT DRIVE VCM = 0.5V 800 Q BASEBAND a. Quadrature Downconversion 600 I BASEBAND 400 SIN LPF AD9854 200 0 RF OUTPUT LPF REFCLK COS Q BASEBAND 0 100 200 300 FREQUENCY - MHz 400 500 b. Direct Conversion Quadrature Upconverter Figure 24. Director Quadrature Up/Down Conversion Applications for the AD9854 Figure 23. Comparator Toggle Voltage Requirement I/Q MIXER AND LOW-PASS FILTER Rx RF IN 8 I Q DUAL 8-/10-BIT ADC Rx BASEBAND DIGITAL DATA OUT DIGITAL DEMODULATOR 8 VCA AGC ADC CLOCK FREQUENCY LOCKED TO Tx CHIP/ SYMBOL/PN RATE ADC ENCODE AD9852 CLOCK GENERATOR REFERENCE CLOCK 48 CHIP/SYMBOL/PN RATE DATA Figure 25. Chip Rate Generator in Spread Spectrum Application BANDPASS FILTER AD9854 AMPLIFIER IOUT 50V REFERENCE CLOCK 50V RF FREQUENCY OUT PHASE COMPARATOR LOOP FILTER AD9854 REF CLK IN VCO FILTER AD9854 SPECTRUM FINAL OUTPUT SPECTRUM FUNDAMENTAL DAC OUT FC + FO IMAGE FC - FO IMAGE FCLK DDS PROGRAMMABLE "DIVIDE-BY-N" FUNCTION (WHERE N = 248/TUNING WORD) FC + FO IMAGE TUNING WORD BANDPASS FILTER Figure 27. Programmable "Fractional Divide-by-N" Synthesizer Figure 26. Using an Aliased Image to Generate a High Frequency -12- REV. 0 AD9854 REF CLOCK AD9854 FILTER DDS PHASE COMPARATOR TUNING WORD RF FREQUENCY OUT VCO LOOP FILTER DIFFERENTIAL TRANSFORMER-COUPLED OUTPUT IOUT FILTER REFERENCE CLOCK DDS AD9854 50V 1:1 TRANSFORMER I.E. MINI-CIRCUITS T1-1T DIVIDE-BY-N Figure 28a. Agile High-Frequency Synthesizer AD8346 QUADRATURE MODULATOR 36dB TYPICAL SSB LO REJECTION 50V 90 VOUT PHASE SPLITTER S 50V IOUT Figure 29. Differential Output Connection for Reduction of Common-Mode Signals COSINE (DC TO 70MHz) 0.8 TO 2.5 GHz AD9854 QUADRATURE DDS 0 LO SINE (DC TO 70MHz) DDS - LO LO DDS + LO NOTES: FLIP DDS QUADRATURE SIGNALS TO SELECT ALTERNATE SIDE-BAND. ADJUST DDS SINE OR COSINE SIGNAL AMPLITUDE FOR GREATEST SIDE-BAND SUPPRESSION. DDS DAC OUTPUTS MUST BE LOW-PASS FILTERED PRIOR TO USE WITH THE AD8346. Figure 28b. Image Reject Mixer ANALOG MULTIPLIER REFERENCE CLOCK SIN LPF AD9854 IF LPF COS Analog Frequency Double Application COMPARATORS AOUT = 100MHz REFERENCE CLOCK SIN LPF AD9854 CLOCK OUT = 200MHz LPF COS Clock Frequency Doubler AD9854 8-BIT PARALLEL OR SERIAL PROGRAMMING DATA AND CONTROL SIGNALS mPROCESSOR/ CONTROLLER FPGA, ETC. 300MHz MAX DIRECT MODE OR 15 TO 75MHz MAX IN THE 43-203 CLOCK MULTIPLIER MODE REFERENCE CLOCK LOW-PASS FILTER "I" DAC 1 LOW-PASS FILTER 2 "Q" DAC OR "CONTROL DAC" + NOTES: IOUT = APPROX 20mA MAX WHEN RSET = 2kV SWITCH POSTION 1 PROVIDES COMPLEMENTARY SINUSOIDAL SIGNALS TO THE COMPARATOR TO PRODUCE A FIXED 50% DUTY CYCLE FROM THE COMPARATOR. SWITCH POSTION 2 PROVIDES THE SAME DUTY CYCLE USING QUADRATURE SINUSOIDAL SIGNALS TO THE COMPARATOR OR A DC THRESHOLD VOLTAGE TO ALLOW SETTING OF THE COMPARATOR DUTY CYCLE (DEPENDS ON THE "Q" DAC's CONFIGURATION) 2kV RSET CMOS LOGIC "CLOCK" OUT Figure 30. Frequency Agile Clock Generator Applications for the AD9854 REV. 0 -13- AD9854 (continued from page 1) architecture allows the generation of simultaneous quadrature outputs at frequencies up to 150 MHz, which can be digitally tuned at a rate of up to 100 million new frequencies per second. The (externally filtered) sine wave output can be converted to a square wave by the internal comparator for agile clock generator applications. The device provides 14 bits of digitally-controlled phase modulation and single-pin PSK. The on-board 12-bit I and Q DACs, coupled with the innovative DDS architecture, provide excellent wideband and narrowband output SFDR. The Q-DAC can also be configured as a user-programmable control DAC if the quadrature function is not desired. When configured with the on-board comparator, the 12-bit control DAC facilitates static duty cycle control in the high-speed clock generator applications. Two 12-bit digital multipliers permit programmable amplitude modulation, shaped on/off keying and precise amplitude control of the quadrature outputs. Chirp functionality is also included which facilitates wide bandwidth frequency sweeping applications. The AD9854's programmable 4x-20x REFCLK multiplier circuit generates the 300 MHz clock internally from a lower frequency external reference clock. This saves the user the expense and difficulty of implementing a 300 MHz clock source. Direct 300 MHz clocking is also accommodated with either single-ended or differential inputs. Single-pin conventional FSK and the enhanced spectral qualities of "ramped" FSK are supported. The AD9854 uses advanced 0.35 micron CMOS technology to provide this high level of functionality on a single 3.3 V supply. An externally generated Update Clock is internally synchronized with the system clock to prevent partial transfer of program register information due to violation of data setup or hold times. This mode gives the user complete control of when updated program information becomes effective. The default mode is set for internal update clock (Int Update Clk control register bit is logic high). To switch to external update clock mode, the Int Update Clk register bit must be set to logic low. The internal update mode generates automatic, periodic update pulses whose time period is set by the user. An internally generated Update Clock can be established by programming the 32-bit Update Clock registers (address 16-19 hex) and setting the Int Update Clk (address 1F hex) control register bit to logic high. The update clock down-counter function operates at the system clock/2 (150 MHz maximum) and counts down from a 32-bit binary value (programmed by the user). When the count reaches 0, an automatic I/O Update of the DDS output or functions is generated. The update clock is internally and externally routed on Pin 20 to allow users to synchronize programming of update information with the update clock rate. The time period between update pulses is given as: (N+1) x (SYSTEM CLOCK PERIOD x 2) where N is the 32-bit value programmed by the user. Allowable range of N is from 1 to (232 -1). The internally generated update pulse output on Pin 20 has a fixed high time of eight system clock cycles. Shaped On/Off Keying The AD9854 is available in a space-saving 80-lead LQFP surface mount package and a thermally-enhanced 80-lead LQFP package. The AD9854 is pin-for-pin compatible with the AD9852 single-tone synthesizer. It is specified to operate over the extended industrial temperature range of -40C to +85C. Allows user to control the ramp-up and ramp-down time of an "on/off" emission from the I and Q DACs. This function is used in "burst transmissions" of digital data to reduce the adverse spectral impact of short, abrupt bursts of data. Users must first enable the digital multipliers by setting the OSK EN bit (control register address 20 hex) to logic high in the control register. OVERVIEW Otherwise, if the OSK EN bit is set low, the digital multipliers responsible for amplitude-control are bypassed and the I and Q DAC outputs are set to full-scale amplitude. In addition to setting the OSK EN bit, a second control bit, OSK INT (also at address 20 hex), must be set to logic high. Logic high selects the linear internal control of the output ramp-up or ramp-down function. A logic low in the OSK INT bit switches control of the digital multipliers to user programmable 12-bit registers allowing users to dynamically shape the amplitude transition in practically any fashion. These 12-bit registers, labeled "Output Shape Key I and Output Shape Key Q" are located at addresses 21 through 24 hex in Table V. The maximum output amplitude is a function of the RSET resistor and is not programmable when OSK INT is enabled. The AD9854 quadrature output digital synthesizer is a highly flexible device that will address a wide range of applications. The device consists of an NCO with 48-bit phase accumulator, programmable reference clock multiplier, inverse sinc filters, digital multipliers, two 12-bit/300 MHz DACs, high-speed analog comparator, and interface logic. This highly integrated device can be configured to serve as a synthesized LO, agile clock generator, and FSK/BPSK modulator. The theory of operation of the functional blocks of the device, and a technical description of the signal flow through a DDS device, can be found in a tutorial from Analog Devices called "A Technical Tutorial on Digital Signal Synthesis." This tutorial is available on CD-ROM and information on obtaining it can be found at the Analog Devices DDS website at www.analog.com/dds. The tutorial also provides basic applications information for a variety of digital synthesis implementations. The DDS background subject matter is not covered in this data sheet; the functions and features of the AD9854 will be individually discussed herein. ABRUPT ON/OFF KEYING USING THE AD9854 Internal and External Update Clock This function is comprised of a bidirectional I/O pin, Pin 20, and a programmable 32-bit down-counter. In order for programming changes to be transferred from the I/O Buffer registers to the active core of the DDS, a clock signal (low to high edge) must be externally supplied to Pin 20 or internally generated by the 32-bit Update Clock. -14- SHAPED ON/OFF KEYING Figure 31. Shaped On/Off Keying REV. 0 AD9854 (BYPASS MULTIPLIER) DIGITAL SIGNAL IN OSK EN = 0 12 12-BIT DIGITAL MULTIPLIER 12 SINE DAC OSK EN = 1 OSK EN = 1 USER PROGRAMMABLE 12-BIT Q-CHANNEL MULTIPLIER "OUTPUT SHAPE KEY Q MULT" REGISTER OSK EN = 0 12 OSK EN = 1 12 OSK EN = 0 12 12-BIT COUNTER 1 8-BIT DOWNCOUNTER SYSTEM CLOCK SHAPING KEYING PIN Figure 32. Block diagram of Q-pathway of the digital multiplier section responsible for Shaped Keying function. The I-pathway is similar, except that no alternate 12-bit Q-DAC source register is provided. Next, the transition time from zero-scale to full-scale must be programmed. The transition time is a function of two fixed elements and one variable. The variable element is the programmable 8-bit RAMP RATE COUNTER. This is a down-counter being clocked at the system clock rate (300 MHz max) that outputs one pulse whenever the counter reaches zero. This pulse is routed to a 12-bit counter that increments one LSB for every pulse received. The outputs of the 12-bit counter are connected to the 12-bit digital multiplier. When the digital multiplier has a value of all zeros at its inputs, the input signal is multiplied by zero, producing zero-scale. When the multiplier has a value of all ones, the input signal is multiplied by a value of one, producing full-scale. There are 4094 remaining fractional multiplier values that will produce output amplitudes corresponding to their binary values. The two fixed elements are the clock period of the system clock, which drives the Ramp Rate Counter, and the 4096 amplitude steps between zero-scale and full-scale. To give an example, assume that the System Clock of the AD9854 is 100 MHz (10 ns period). If the Ramp Rate Counter is programmed for a minimum count of five, it will take two system clock periods (one rising edge loads the count-down value, the next edge decrements the counter from five to four). The relationship of the 8-bit countdown value to the time period between output pulses is given as: (N+1) x SYSTEM CLOCK PERIOD, where N is the 8-bit count-down value. It will take 4096 of these pulses to advance the 12-bit up-counter from zero-scale to fullscale. Therefore, the minimum shaped keying ramp time for a 100 MHz system clock is 4096 x 6 x 10 ns = approximately 246 s. The maximum ramp time will be 4096 x 256 x 10 ns = approximately 10.5 s. Finally, changing the logic state of Pin 30, "shaped keying" will automatically perform the programmed output envelope functions when OSK INT is high. A logic high on Pin 30 causes the outputs to linearly ramp up to full-scale amplitude and hold until the logic level is changed to low, causing the outputs to ramp down to zero-scale. I and Q DACs The 300 MSPS (maximum) sine and cosine wave outputs of the DDS. Their maximum output amplitudes are set by the DAC RSET resistor at Pin 56. These are current-out DACs with a full-scale maximum output of 20 mA; however, a nominal 10 mA REV. 0 output current provides best spurious-free dynamic range (SFDR) performance. The value of RSET = 39.93/IOUT, where IOUT is in amps. DAC output compliance specification limits the maximum voltage developed at the outputs to -0.5 V to +1 V. Voltages developed beyond this limitation will cause excessive DAC distortion and possibly permanent damage. The user must choose a proper load impedance to limit the output voltage swing to the compliance limits. Both DAC outputs should be terminated equally for best SFDR, especially at higher output frequencies where harmonic distortion errors are more prominent. Both DACs are preceded by inverse SIN(x)/x filters (a.k.a. inverse sinc filters) that precompensate for DAC output amplitude variations over frequency to achieve flat amplitude response from dc to Nyquist. Digital multipliers follow the inverse sinc filters to allow amplitude control, amplitude modulation and amplitude shaped keying. The inverse sinc filters (address 20 hex, Bypass Inv Sinc bit)) and digital multipliers (address 20 hex, OSK EN bit) can be bypassed for power conservation by setting those bits high. Both DACs can be powered down by setting the DAC PD bit high (address 1D of control register) when not needed. I-DAC outputs are designated as IOUT1 and IOUT1B, Pins 48 and 49 respectively. Q-DAC outputs are designated as IOUT2 AND IOUT2B, Pins 52 and 51 respectively. Control DAC The 12-bit Q DAC can be reconfigured to perform as a "control" or auxiliary DAC. The control DAC output can provide dc control levels to external circuitry, generate ac signals, or enable duty cycle control of the on-board comparator. When the SRC QDAC bit in control register (parallel address 1F hex) is set high, the Q DAC inputs are switched from internal 12-bit Q data source (default setting) to external 12-bit, twos-complement data, supplied by the user. Data is channeled through the serial or parallel interface to the 12-bit Q DAC register (address 26 and 27 hex) at a maximum 100 MHz data rate. This DAC is clocked at the system clock, 300 MSPS (maximum), and has the same maximum output current capability as that of the I DAC. The single RSET resistor on the AD9854 sets the full-scale output current for both DACs. The control DAC can be separately powered down for power conservation when not needed by setting the Q DAC POWER-DOWN bit high (address 1D hex). Control DAC outputs are designated as IOUT2 and IOUT2B (Pins 52 and 51 respectively). -15- AD9854 0 0 IMAGES -10 -10 -20 -20 -30 -30 -40 -40 -50 -50 -60 -70 -60 FUNDAMENTAL OUTPUT POWER DECREASES WITH INCREASING FREQUENCY -70 -80 -80 -90 -90 -100 FUNDAMENTAL OUTPUT POWER IS "FLAT" FROM DC TO 1/2 FCLK -100 10MHz/ CENTER 50MHz SPAN 100MHz 10MHz/ CENTER 50MHz Figure 33. Normal SIN(x)/x DAC Output Power Envelope Filter SPAN 100MHz Figure 34. Inverse SIN(x)/x (Inverse SINC) Filter Engaged The REFCLK Multiplier function can be bypassed to allow direct clocking of the AD9854 from an external clock source. The system clock for the AD9854 is either the output of the REFCLK Multiplier (if it is engaged) or the REFCLK inputs. REFCLK may be either a single-ended or differential input by setting Pin 64, DIFF CLK ENABLE, low or high respectively. Inverse SINC Function This filter precompensates input data to both DACs for the SIN(x)/x roll-off function to allow wide bandwidth signals (such as QPSK) to be output from the DACs without appreciable amplitude variations that will cause increased EVM (error vector magnitude). The inverse SINC function may be bypassed to significantly reduce power consumption, especially at higher clock speeds. When the Q DAC is configured as a "control" DAC, the inverse SINC function does not apply. PLL Range Bit Inverse SINC is engaged by default and is bypassed by bringing the "Bypass Inv SINC" bit high in control register 20 (hex) in Table V. REFCLK Multiplier This is a programmable PLL-based reference clock multiplier that allows the user to select an integer clock multiplying value over the range of 4x to 20x by which the REFCLK input will be multiplied. Use of this function allows users to input as little as 15 MHz to produce a 300 MHz internal system clock. Five bits in control register 1E hex set the multiplier value as follows in Table I. The PLL Range Bit selects the frequency range of the REFCLK Multiplier PLL. For operation from 200 MHz to 300 MHz (internal system clock rate) the PLL Range Bit should be set to Logic 1. For operation below 200 MHz, the PLL Range Bit should be set to Logic 0. The PLL Range Bit adjusts the PLL loop parameters for optimized phase noise performance within each range. Pin 61, PLL FILTER This pin provides the connection for the external zero compensation network of the PLL loop filter. The zero compensation network consists of a 1.3 k resistor in series with a 0.01 F capacitor. The other side of the network should be connected to as close as possible to Pin 60, AVDD. For optimum phase noise performance the clock multiplier can be bypassed by setting the "Bypass PLL" bit in control register address 1E. Table I. REFCLK Multiplier Control Register Values Multiplier Value Ref Mult 4 Ref Mult 3 Ref Mult 2 Ref Mult 1 Ref Mult 0 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 -16- REV. 0 AD9854 Differential REFCLK Enable Table II. Mode Selection Table A high level on this pin enables the differential clock Inputs, REFCLOCK and REFCLOCKB (Pins 69 and 68 respectively). The minimum differential signal amplitude required is 800 mV p-p. The centerpoint or common-mode range of the differential signal can range from 1.6 V to 1.9 V. When Pin 64 (DIFF CLK ENABLE) is tied low, REFCLK (Pin 69) is the only active clock input. This is referred to as the single-ended mode. In this mode, Pin 68 (REFCLKB) should be tied low or high, but not left floating. Parallel/Serial Programming Mode Setting Pin 70 high invokes parallel mode, whereas setting Pin 70 low will invoke the serial programming mode. Please refer to the text describing the serial and parallel programming protocol contained in this data sheet for further information. Two control bits located at address 20 hex in the Table V apply only to the serial programming mode. LSB First when high, dictates that serial data will be loaded starting with the LSB of the word. When low (the default value), serial data is loaded starting with the MSB of the word. SDO Active when high indicates that the SDO pin, Pin 18, is dedicated as an output to read back data from the AD9854 registers. When SDO Active is low (default value), this indicates that the SDIO pin, Pin 19, acts as a bidirectional serial data input and output pin and Pin 18 has no function in the serial mode. DESCRIPTION OF AD9854 MODES OF OPERATION There are five programmable modes of operation of the AD9854. Selecting a mode requires that three bits in the Control Register (parallel address 1F hex) be programmed as follows in Table II. Mode 2 Mode 1 Mode 0 Result 0 0 0 0 1 0 0 1 1 0 0 1 0 1 0 SINGLE-TONE FSK RAMPED FSK CHIRP BPSK In each mode, engaging certain functions may or may not be permitted. Shown in Table III is a listing of some important functions and their availability for each mode. Single-Tone (Mode 000) This is the default mode when master reset is asserted or when it is user-programmed into the control register. The Phase Accumulator, responsible for generating an output frequency, is presented with a 48-bit value from Frequency Tuning Word 1 registers whose default values are zero. Default values from the remaining applicable registers will further define the single-tone output signal qualities. The default values after a master reset, define a safe, "no output" value resulting in an output signal of 0 Hertz, 0 phase. Upon power-up and reset the output from both I and Q DACs will be a dc value equal to the midscale output current. This is the default mode amplitude setting of zero. Refer to the digital multiplier section for further explanation of the output amplitude control. It will be necessary to program all or some of the 28 program registers to realize a user-defined output signal. Figure 35 graphically shows the transition from the default condition (0 Hz) to a user defined output frequency (F1). As with all Analog Devices DDSs, the value of the frequency tuning word is determined using the following equation: FREQUENCY FTW = (Desired Output Frequency x 2N)/SYSCLK. F1 0 MODE 000 (DEFAULT) 000 (SINGLE TONE) 0 F1 TW1 Figure 35. Default State to User-Defined Output Transition Table III. Function Availability vs. Mode of Operation Mode Phase Adjust 1 Phase Adjust 2 Single-Pin FSK/BPSK or HOLD Single-Pin ShapedKeying Phase Offset or Modulation Amplitude Control or Modulation Inverse SINC Filter Frequency Tuning Word 1 Frequency Automatic Tuning Frequency Word 2 Sweep Single-Tone FSK Ramped FSK CHIRP BPSK X X X X X X X X X REV. 0 -17- X X X AD9854 Where N is the phase accumulator resolution (48 bits in this instance), frequency is expressed in Hertz, and the FTW, Frequency Tuning Word, is a decimal number. Once a decimal number has been calculated, it must be rounded to an integer and then converted to binary format--a series of 48 binaryweighted 1s or 0s. The fundamental sine wave DAC output frequency range is from dc to 1/2 SYSCLK. Furthermore, all of these qualities can be changed or modulated via the 8-bit parallel programming port at a 100 MHz parallel-byte rate, or at a 10 MHz serial rate. Incorporating this attribute will permit FM, AM, PM, FSK, PSK, ASK operation in the singletone mode. Unramped FSK (Mode 001) Changes in frequency are phase continuous--that is, the new frequency uses the last phase of the old frequency as the reference point to compute the first new frequency phase. The I and Q DACs of the AD9854 are always 90 degrees outof-phase. The 14-bit phase registers (discussed elsewhere in this data sheet) do not independently adjust the phase of each DAC output. Instead, both DAC's are affected equally by a change in phase offset. The single-tone mode allows the user to control the following signal qualities: * Output Frequency to 48-Bit Accuracy * Output Amplitude to 12-Bit Accuracy - Fixed, User-Defined, Amplitude Control - Variable, Programmable Amplitude Control - Automatic, Programmable, Single-Pin-Controlled, "Shaped On/Off Keying" * Output Phase to 14-Bit Accuracy When selected, the output frequency of the DDS is a function of the values loaded into Frequency Tuning Word registers 1 and 2 and the logic level of Pin 29 (FSK/BPSK/HOLD). A logic low on Pin 29 chooses F1 (frequency tuning word 1, parallel address 4-9 hex) and a logic high chooses F2 (frequency tuning word 2, parallel register address A-F hex). Changes in frequency are phase-continuous and practically instantaneous. (Please refer to pipeline delays in specification table.) Other than F2 and Pin 29 becoming active, this mode is identical to single-tone. The unramped FSK mode, Figure 36, is representative of traditional FSK, RTTY (Radio Teletype) or TTY (Teletype) transmission of digital data. Frequency transitions occur nearly instantaneously from F1 to F2. This simple method works extremely well and is the most reliable form of digital communication, but it is also wasteful of RF spectrum. See the following Ramped FSK section for an alternative FSK method that conserves bandwidth. FREQUENCY F2 F1 0 000 (DEFAULT) 001 (FSK NO RAMP) TW1 0 F1 TW2 0 F2 MODE FSK DATA (PIN 29) Figure 36. Traditional FSK Mode FREQUENCY F2 F1 0 000 (DEFAULT) 010 (RAMPED FSK) TW1 0 F1 TW2 0 F2 MODE FSK DATA (PIN 29) Figure 37. Ramped FSK Mode -18- REV. 0 AD9854 FREQUENCY F2 F1 0 000 (DEFAULT) 010 (RAMPED FSK) TW1 0 F1 TW2 0 F2 MODE FSK DATA Figure 38. Ramped FSK Mode Ramped FSK (Mode = 010) A method of FSK whereby changes from F1 to F2 are not instantaneous but, instead, are accomplished in a frequency sweep or "ramped" fashion. The "ramped" notation implies that the sweep is linear. While linear sweeping or frequency ramping is easily and automatically accomplished, it is only one of many possibilities. Other frequency transition schemes may be implemented by changing the ramp rate and ramp step size "on-the-fly," in piecewise fashion. where N is the 20-bit ramp rate clock value programmed by the user. Allowable range of N is from 1 to (220 -1). The output of this counter clocks the 48-bit Frequency Accumulator shown below in Figure 39. The Ramp Rate Clock determines the amount of time spent at each intermediate frequency between F1 and F2. The counter stops automatically when the destination frequency is achieved. The "dwell time" spent at F1 and F2 is determined by the duration that the FSK input, Pin 29, is held high or low after the destination frequency has been reached. Frequency ramping, whether linear or nonlinear, necessitates that many intermediate frequencies between F1 and F2 will be output in addition to the primary F1 and F2 frequencies. Figures 37 and 38 graphically depict the frequency versus time characteristics of a linear ramped FSK signal. OUT ADDER FREQUENCY ACCUMULATOR The purpose of ramped FSK is to provide better bandwidth containment than traditional FSK by replacing the instantaneous frequency changes with more gradual, user-defined frequency changes. The dwell time at F1 and F2 can be equal to or much greater than the time spent at each intermediate frequency. The user controls the dwell time at F1 and F2, the number of intermediate frequencies and time spent at each frequency. Unlike unramped FSK, ramped FSK requires the lowest frequency to be loaded into F1 registers and the highest frequency into F2 registers. Several registers must be programmed to instruct the DDS regarding the resolution of intermediate frequency steps (48 bits) and the time spent at each step (20 bits). Furthermore, the CLR ACC1 bit in the control register should be toggled (low-highlow) prior to operation to assure that the frequency accumulator is starting from an "all zeros" output condition. For piecewise, nonlinear frequency transitions, it is necessary to reprogram the registers while the frequency transition is in progress to affect the desired response. Parallel register addresses 1A-1C hex comprise the 20-bit "Ramp Rate Clock" registers. This is a countdown counter that outputs a single pulse whenever the count reaches zero. The counter is activated any time a logic level change occurs on FSK input Pin 29. This counter is run at the System Clock Rate, 300 MHz maximum. The time period between each output pulse is given as (N+1) x (SYSTEM CLOCK PERIOD) REV. 0 PHASE ACCUMULATOR 48-BIT DELTAFREQUENCY WORD FREQUENCY TUNING WORD 1 20-BIT RAMP RATE CLOCK FREQUENCY TUNING WORD 2 FSK (PIN 29) SYSTEM CLOCK Figure 39. Block Diagram of Ramped FSK Function Parallel register addresses 10-15 hex comprise the 48-bit, straight binary, "Delta Frequency Word" registers. This 48-bit word is accumulated (added to the accumulator's output) every time it receives a clock pulse from the ramp rate counter. The output of this accumulator is then added to or subtracted from the F1 or F2 frequency word, which is then fed to the input of the 48-bit Phase Accumulator that forms the numerical phase steps for the sine and cosine wave outputs. In this fashion, the output frequency is ramped up and down in frequency, according to the logicstate of Pin 29. The rate at which this happens is a function of the 20-bit ramp rate clock. Once the destination frequency is achieved, the ramp rate clock is stopped, which halts the frequency accumulation process. -19- AD9854 F2 FREQUENCY FREQUENCY F2 F1 F1 0 0 MODE 010 (RAMPED FSK) TW1 F1 TW2 F2 MODE 000 (DEFAULT) FSK DATA 010 (RAMPED FSK) TW1 0 F1 TW2 0 F2 FSK DATA TRIANGLE BIT TRIANGLE BIT Figure 40. Effect of Triangle Bit in Ramped FSK Mode Generally speaking, the Delta Frequency Word will be a much smaller value as compared to that of the F1 or F2 tuning word. For example, if F1 and F2 are 1 kHz apart at 13 MHz, the Delta Frequency Word might be only 25 Hz. Figure 41 shows that premature toggling causes the ramp to immediately reverse itself and proceed at the same rate and resolution back to originating frequency. Figure 42. Automatic Linear Ramping Using the Triangle Bit The control register contains a Triangle bit at parallel register address 1F hex. Setting this bit high in Mode 010 causes an automatic ramp-up and ramp-down between F1 and F2 to occur without having to toggle Pin 29 as shown in Figure 40. In fact, the logic state of Pin 29 has no effect once the Triangle bit is set high. This function uses the ramp-rate clock time period and the delta-frequency-word step size to form a continuously sweeping linear ramp from F1 to F2 and back to F1 with equal dwell times at every frequency. Using this function, one can automatically sweep from dc to the Nyquist limit or any other two frequencies between dc and Nyquist. FREQUENCY F2 F1 0 000 (DEFAULT) 010 (RAMPED FSK) TW1 0 F1 TW2 0 F2 MODE FSK DATA Figure 41. Effect of Premature Ramped FSK Data -20- REV. 0 AD9854 In the Ramped FSK mode, with the triangle bit set high, an automatic frequency sweep will begin at either F1 or F2, according to the logic level on Pin 29 (FSK input pin) when the triangle bit's rising edge occurs as shown in Figure 42. If the FSK data bit had been high instead of low, F2 would have been chosen instead of F1 as the start frequency. accumulator (ACC2). When this bit is set high, the output of the phase accumulator will result in 0 Hz output from the DDS. As long as this bit is set high, the frequency and phase accumulators will be cleared, resulting in 0 Hz output. To return to previous DDS operation, CLR ACC2 must be set to logic low. Additional flexibility in the ramped FSK mode is provided in the ability to respond to changes in the 48-bit delta frequency word and/or the 20-bit ramp-rate counter on-the-fly during the ramping from F1 to F2 or vice versa. To create these nonlinear frequency changes it is necessary to combine several linear ramps in a piecewise fashion whose slopes are different. This is done by programming and executing a linear ramp at some rate or "slope" and then altering the slope (by changing the ramp rate clock or delta frequency word or both). Changes in slope are made as often as needed to form the desired nonlinear frequency sweep response before the destination frequency has been reached. These piecewise changes can be precisely timed using the 32-bit Internal Update Clock (see detailed description elsewhere in this data sheet). This mode is also known as pulsed FM. Most chirp systems use a linear FM sweep pattern although any pattern may be used. This is a type of spread spectrum modulation that can realize "processing gain." In radar applications, use of chirp or pulsed FM allows operators to significantly reduce the output power needed to achieve the same result as a single-frequency radar system would produce. Figure 43 represents a very low-resolution nonlinear chirp meant to demonstrate the different "slopes" that are created by varying the time steps (ramp rate) and frequency steps (delta frequency word). Nonlinear ramped FSK will have the appearance of a chirp function that is graphically illustrated in Figure 43. The major difference between a ramped FSK function and a chirp function is that FSK is limited to operation between F1 and F2. Chirp operation has no F2 limit frequency. Chirp (Mode 011) The AD9854 permits precise, internally generated linear or externally programmed nonlinear pulsed or continuous FM over a user-defined frequency range, duration, frequency resolution and sweep direction(s). A block diagram of the FM chirp components is shown in Figure 44. OUT ADDER Two additional control bits are available in the ramped FSK mode that allow even more options. CLR ACC1, register address 1F hex, will, if set high, clear the 48-bit frequency accumulator (ACC1) output with a retriggerable one-shot pulse of one system clock duration. If the CLR ACC1 bit is left high, a one-shot pulse will be delivered on the rising edge of every Update Clock. The effect is to interrupt the current ramp, reset the frequency back to the start point, F1 or F2, and then continue to ramp up (or down) at the previous rate. This will occur even when a static F1 or F2 destination frequency has been achieved. (See Figure 43.) FREQUENCY ACCUMULATOR 48-BIT DELTAFREQUENCY WORD FREQUENCY CLR ACC1 20-BIT RAMP RATE CLOCK HOLD F1 000 (DEFAULT) 010 (RAMPED FSK) 0 F1 DFW RAMP RATE Figure 43. Example of a Nonlinear Chirp REV. 0 SYSTEM CLOCK Figure 44. FM Chirp Components 0 TW1 CLR ACC2 FREQUENCY TUNING WORD 1 Next, CLR ACC2 control bit (register address 1F hex) is available to clear both the frequency accumulator (ACC1) and the phase MODE PHASE ACCUMULATOR -21- AD9854 Basic FM Chirp Programming Steps Two control bits are available in the FM Chirp mode that will allow practically instantaneous return to the beginning frequency, FTW1, or to 0 Hz. First, CLR ACC1 bit, register address 1F hex, will, if set high, clear the 48-bit frequency accumulator (ACC1) output with a retriggerable one-shot pulse of one system clock duration. The 48-bit Delta Frequency Word input to the accumulator is unaffected by CLR ACC1 bit. If the CLR ACC1 bit is left high, a one-shot pulse will be delivered to the Frequency Accumulator (ACC1) on every rising edge of the I/O Update Clock. The effect is to interrupt the current chirp, reset the frequency back to FTW1, and continue the chirp at the previously programmed rate and direction. Clearing the Frequency Accumulator in the chirp mode is illustrated in Figure 45. Not shown in the diagram is the I/O update signal, which is either usersupplied or internally generated. A discussion of I/O Update is presented elsewhere in this data sheet. 1. Program a start frequency into Frequency Tuning Word 1 (parallel register addresses 4-9 hex) hereafter called FTW1. 2. Program the frequency step resolution into the 48-bit, twos complement, Delta Frequency Word (parallel register addresses 10-15 hex). 3. Program the rate of change (time at each frequency) into the 20-bit Ramp Rate Clock (parallel register addresses 1A-C). 4. When programming is complete, an I/O update pulse at Pin 20 will engage the program commands. The necessity for a twos complement Delta Frequency Word is to define the direction in which the FM chirp will move. If the 48-bit delta frequency word is negative (MSB is high) then the incremental frequency changes will be in a negative direction from FTW1. If the 48-bit word is positive (MSB is low) then the incremental frequency changes will be in a positive direction. FREQUENCY It is important to note that the FTW1 is only a starting point for FM chirp. There is no built-in restraint requiring a return to FTW1. Once the FM chirp has left FTW1 it is free to move (under program control) within the Nyquist bandwidth (dc to 1/2 system clock). Instant return to FTW1 is easily achieved, though, and this option is explained in the next few paragraphs. Next, CLR ACC2 control bit (register address 1F hex) is available to clear both the frequency accumulator (ACC1) and the phase accumulator (ACC2). When this bit is set high, the output of the phase accumulator will result in 0 Hz output from the DDS. As long as this bit is set high, the frequency and phase accumulators will be cleared, resulting in 0 Hz output. To return to previous DDS operation, CLR ACC2 must be set to logic low. This bit is useful in generating pulsed FM. F1 0 MODE 000 (DEFAULT) 011 (CHIRP) FTW1 0 F1 DFW DELTA FREQUENCY WORD RAMP RATE RAMP RATE I/O UPDATE CLOCK CLR ACC1 Figure 45. Effect of CLR ACC1 in FM Chirp Mode -22- REV. 0 FREQUENCY AD9854 F1 0 MODE 000 (DEFAULT) 011 (CHIRP) 0 TW1 DPW RAMP RATE CLR ACC2 FREQUENCY Figure 46. Effect of CLR ACC2 in FM Chirp Mode F1 0 MODE TW1 000 (DEFAULT) 011 (CHIRP) 0 F1 DELTA FREQUENCY WORD DFW RAMP RATE RAMP RATE HOLD Figure 47. Illustration of HOLD Function FM Chirp Figure 46 graphically illustrates the effect of CLR ACC2 bit upon the DDS output frequency. Note that reprogramming the registers while the CLR ACC2 bit is high allows a new FTW1 frequency and slope to be loaded. Another function that is available only in the chirp mode is the HOLD pin, Pin 29. This function will stop the clocking signal to the ramp rate counter that will, in turn, halt any further clocking pulses to the frequency accumulator, ACC1. The effect is to halt the chirp and hold the output frequency in a static condition at the frequency existing just before HOLD was pulled high. When the HOLD pin is returned low, the clocks are resumed and chirp continues. During a hold condition, user may change the programming registers; however, the ramp rate counter must resume operation at its previous rate until a count of zero is obtained before a new ramp rate count can be loaded. Figure 47 illustrates the effect of the hold function on the DDS output frequency. REV. 0 Users may utilize the 32-bit automatic I/O Update counter when constructing complex chirp or ramped FSK sequences. Since this internal counter is synchronized with the AD9854 System Clock, it allows precisely timed program changes to be invoked. In this manner, user is only required to reprogram the desired registers before the automatic I/O Update pulse is generated. A complete discussion of this function is presented elsewhere in this data sheet. In the chirp mode, the destination frequency is not directly specified. If the user fails to control the chirp, the DDS will control itself by naturally confining its output between dc and Nyquist; however, unless terminated by the user, the chirp will continue until power is removed. It is the user's choice as to what occurs when the chirp destination frequency is reached. Here are a few of the choices: 1. Stop and hold at the destination frequency using the HOLD pin, or by loading all zeros into the Delta Frequency Word registers of the frequency accumulator (ACC1). -23- AD9854 2. Stop using the hold pin function, then ramp-down the output amplitude using the digital multiplier stages and the Shaped Keying pin, Pin 30, or via program register control (addresses 21-24 hex). If phase shift keying is not the objective, but rather a broader range of phase offsets is needed, the user should select the Single Tone mode and program Phase Adjust register 1 using the serial or high-speed parallel programming bus. 3. Stop and abruptly terminate the transmission using the CLR ACC2 bit. I/O Port Buffers--100 MHz, 8-bit parallel or 10 MHz serial loading, SPI-compatible. The programming mode is selected externally via the serial/parallel (S/P Select) pin. I/O Buffers can be written to, or read from, according to the signals supplied to the Read (RDB) and Write pins (WRB) and the 6-bit address (A0-A5) in the parallel mode or to CSB, SCLK and SDIO pins in the Serial mode. 4. Continue chirp by reversing direction and returning to the previous, or another, destination frequency in a linear or userdirected manner. If this involves going down in frequency, a negative 48-bit Delta Frequency Word (the MSB is set to "1") must be loaded into registers 10-15 hex. Any decreasing frequency step of the Delta Frequency Word requires the MSB to be set to logic high. 5. Continue chirp by immediately returning to the F1 beginning frequency in a sawtooth fashion and repeat the previous chirp process again. This is where CLR ACC1 control bit is used. An automatic, repeating chirp can be setup using the 32-bit Update Clock to issue CLR ACC1 commands at precise time intervals. Adjusting the timing intervals or changing the Delta Frequency Word will change the chirp range. It is incumbent upon the user to balance the chirp duration and frequency resolution to achieve the proper frequency range. BPSK (Mode 100) Binary, biphase or bipolar phase shift keying is a means to rapidly select between two preprogramming 14-bit output phase offsets that will identically affect both the I and Q outputs of the AD9854. The logic-state of Pin 29, BPSK pin, controls the selection of Phase Adjust register number 1 or 2. When low, Pin 29 selects Phase Adjust register 1; when high, Phase Adjust register 2 is selected. Figure 48 illustrates phase changes made to four cycles of an output carrier. Basic BPSK programming steps: 1. Program a carrier frequency into Frequency Tuning Word 1. 2. Program appropriate 14-bit phase words in Phase Adjust registers 1 and 2. 3. Attach BPSK data source to Pin 29. 4. Activate I/O Update pulse when ready. Data in the I/O Port Buffers is stored until overwritten by changes in program instructions supplied by the user or until power is removed. An I/O Update clocks-in the data from the I/O Buffers to the DDS Programming Registers where it is executed. AM--amplitude modulation of the I and Q DACs is possible using the I/O port to control 12-bit digital multiplier stages that precede the DACs. The multipliers can also be used to set the DAC outputs between zero- and full-scale for static amplitude adjustment. Both I and Q DAC amplitudes are individually programmable. See the "Shaped On/Off Keying" description for more information. Shaped keying function does not apply to the Q DAC when configured as a Control DAC. In this instance, the user is in control of the Control DAC output level via the 12-bit QDAC register at address 26 and 27 hex of the programming registers High-Speed Comparator--optimized for high speed, >300 MHz toggle rate, low jitter, sensitive input, built-in hysteresis and an output level of 1 V p-p minimum into 50 or CMOS logic levels into high impedance loads. The comparator can be separately powered down to conserve power. This comparator is used in "clock generator" applications to square up a bandpass or low-pass filtered sine wave. Eight-Bit Ramp Rate Clock--when Shaped On/Off Keying is engaged, this down-counter takes the system clock (300 MHz maximum), and divides it by an 8-bit binary value (programmed by the user) to produce a user-defined clock. The clock outputs one pulse every time the counter counts down to zero. This clock is 360 PHASE PHASE AFTER ONSET PHASE BEFORE ONSET 0 MODE 000 (DEFAULT) 100 (BPSK) FTW1 0 F1 PHASE ADJUST 1 270 DEGREES PHASE ADJUST 2 90 DEGREES BPSK DATA Figure 48. BPSK Mode -24- REV. 0 AD9854 used to set the rate-of-change of the 12-bit digital multipliers of the I and Q DACs to perform an output shaping function. Twenty-Bit Ramp Rate Clock--when selected, this downcounter takes the system clock (300 MHz maximum) and divides it by a 20-bit binary value (programmed by the user) to produce a user-defined clock. The clock outputs one pulse every time the counter counts down to zero. This clock is used to set the rateof-frequency-change of the ramped FSK or FM Chirp modes. Forty-Eight-Bit Delta Frequency Register--is used only in the Chirp and ramped-FSK modes. This register is loaded with a 48-bit word that represents the frequency increment value of Frequency Accumulator (ACCU 1) whose output will be added to a frequency that is set in either F1 or F2 frequency registers. This register is periodically incremented at a rate set by the 20-bit ramp rate clock (150 MHz maximum). Forty-Eight-Bit Delta Frequency Register--is programmed with a 48-bit Frequency Tuning Word that is input to the 48-bit Phase Accumulator (ACCU 2) and determines the output frequency of the DDS in the single-tone mode. When ramped-FSK or Chirp are selected, this register is sent to a digital adder where it is summed with the output of ACCU 1 before being input to ACCU 2. Therefore, the signal sent to ACCU 2 may be either static or changing at a rate of up to 150 million 48-bit frequency tuning words per second. REV. 0 Power-Down--Several individual stages, when not needed, can be powered down to reduce power consumption via the programming registers while still maintaining functionality of desired stages. These stages are identified in the Register Layout table, address 1D hex. Power-down is achieved by setting the specified bits to logic high. A logic low indicates that the stages are powered up. Furthermore, and perhaps most significantly, two intensely digital stages, the Inverse Sinc filters and the Digital Multiplier stages, can be bypassed to achieve significant power reduction through programming of the control registers in address 20 hex. Again, logic high will cause the stage to be bypassed. Of particular importance is the Inverse Sinc filter as this stage consumes a significant amount of power. A full power-down occurs when all four PD Bits in control register 1D hex are set to logic high. This reduces power consumption to approximately 10 mW (3 mA). Master RESET--logic high active, must be held high for a minimum of 10 system clock cycles. This causes the communications bus to be initialized and loads default values listed in the Table V. -25- AD9854 Table V. Register Layout. Shaded Sections Comprise the Control Register Parallel Address Serial Address Hex Hex Bit 7 00 01 0 Phase Adjust Register #1 <13:8> (Bits 15, 14 don't care) Phase Adjust Register #1 <7:0> Phase 1 00h 00h 02 03 1 Phase Adjust Register #2 <13:8:> (Bits 15, 14 don't care) Phase Adjust Register #2 <7:0> Phase 2 00h 00h 04 05 06 07 08 09 2 Frequency Tuning Word 1 <47:0> Frequency Tuning Word 1 <39:32> Frequency Tuning Word 1 <31:24> Frequency Tuning Word 1 <23:16> Frequency Tuning Word 1 <15:8> Frequency Tuning Word 1 <7:0> Frequency 1 00h 00h 00h 00h 00h 00h 0A 0B 0C 0D 0E 0F 3 Frequency Tuning Word 2 <47:40> Frequency Tuning Word 2 <39:32> Frequency Tuning Word 2 <31:24> Frequency Tuning Word 2 <23:16> Frequency Tuning Word 2 <15:8> Frequency Tuning Word 2 <7:0> Frequency 2 00h 00h 00h 00h 00h 00h 10 11 12 13 14 15 4 Delta Frequency Word <47:40> Delta Frequency Word <39:32> Delta Frequency Word <31:24> Delta Frequency Word <23:16> Delta Frequency Word <15:8> Delta Frequency Word <7:0> 00h 00h 00h 00h 00h 00h 16 17 18 19 5 Update Clock <31:24> Update Clock <23:16> Update Clock <15:8> Update Clock <7:0> 00h 00h 00h 40h 1A 1B 1C 6 Ramp Rate Clock <19:16> (Bits 23, 22, 21, 20 don't care) Ramp Rate Clock <15:8> Ramp Rate Clock <7:0> 00h 00h 00h 1D 7 Don't Care Don't Care Don't Care Comp PD Reserved, Always Low QDAC PD DAC PD DIG PD 00h 1F Don't Care PLL Range Bypass PLL Ref Mult 4 Ref Mult 3 Ref Mult 2 Ref Mult 1 Ref Mult 0 64h 20 CLR ACC 1 CLR ACC 2 Triangle SRC QDAC Mode 2 Mode 1 Mode 0 Int Update Clk 01h Don't Care Bypass Inv Sinc OSK EN OSK INT Don't Care Don't Care LSB First SDO Active 20h AD9854 Register Layout Bit 6 Bit 5 Bit 4 1E Bit 3 Bit 2 Bit 1 Bit 0 Default Value 21 22 8 Output Shape Key I Mult <11:8> (Bits 15, 14, 13, 12 don't care) Output Shape Key I Mult <7:0> 00h 00h 23 24 9 Output Shape Key Q Mult <11:8> (Bits 15, 14, 13, 12 don't care) Output Shape Key Q Mult <7:0> 00h 00h 25 A Output Shape Key Ramp Rate <7:0> 80h 26 27 B QDAC <11:8> (Bits 15, 14, 13, 12 don't care) QDAC <7:0> (Data is required to be in twos complement format) 00h 00h -26- REV. 0 AD9854 Interfacing and Programming the AD9854 1. Internally, controlled at a rate programmable by the user or, The AD9854 Register Layout, shown in Table V, contains the information that programs the chip for the desired functionality. While many applications will require very little programming to configure the AD9854, some will make use of all twelve accessible register banks. The AD9854 supports an 8-bit byte parallel I/O operation or an SPI-compatible serial I/O operation. All accessible registers can be written and read back in either I/O operating mode. 2. Externally, controlled by the user. I/O operations can occur in the absence of REFCLK but the data cannot be moved from the buffer memory to the register bank without REFCLK. See the Update Clock Operation section of this document for details. An external pin, S/P SELECT, is used to configure the I/O mode. Systems that use the parallel I/O mode must connect the S/P SELECT pin to VDD. Systems that operate in the serial I/O mode must tie the S/P SELECT pin to GND. Regardless of mode, the I/O port data is written to a buffer memory that does NOT affect operation of the part until the contents of the buffer memory are transferred to the register banks. This transfer of information occurs synchronously to the system clock and occurs in one of two ways: Parallel I/O Operation With the S/P SELECT pin tied high, the parallel I/O mode is active. The I/O port is compatible with industry standard DSPs and microcontrollers. Six address bits, eight bidirectional data bits and separate write/read control inputs make up the I/O port pins. Parallel I/O operation allows write access to each byte of any register in a single I/O operation at 100 MHz. Read back capability for each register is included to ease designing with the AD9854. Reads are not guaranteed at 100 MHz as they are intended for software debug only. Parallel I/O operation timing diagrams are shown in the Figures 49 and 50. A<5:0> A1 A2 A3 D<7:0> D1 D2 D3 RD TRDHOZ TRDLOV TAHD TADV SPECIFICATION TADV TAHD TRDLOV TRDHOZ VALUE 15ns 5ns 15ns 10ns DESCRIPTION ADDRESS TO DATA VALID TIME (MAXIMUM) ADDRESS HOLD TIME TO RD SIGNAL INACTIVE (MINIMUM) RD LOW TO OUTPUT VALID (MAXIMUM) RD HIGH TO DATA THREE-STATE (MAXIMUM) Figure 49. Parallel Port Read Timing Diagram A<5:0> D<7:0> A1 A2 A3 D1 D2 D3 WR TASU TAHD TDSU TWRHIGH TWRLOW TDHD TWR SPECIFICATION TASU TDSU TADH TDHD TWRLOW TWRHIGH TWR VALUE 4ns 2ns 5ns 0ns 3ns 7ns 3ns DESCRIPTION ADDRESS SETUP TIME TO WR SIGNAL ACTIVE DATA SETUP TIME TO WR SIGNAL INACTIVE ADDRESS HOLD TIME TO WR SIGNAL INACTIVE DATA HOLD TIME TO WR SIGNAL INACTIVE WR SIGNAL MINIMUM LOW TIME WR SIGNAL MINIMUM HIGH TIME WR SIGNAL MINIMUM PERIOD Figure 50. Parallel Port Write Timing Diagram REV. 0 -27- AD9854 Serial Port I/O Operation Table VII. Register Address vs. Data Bytes Transferred With the S/P SELECT pin tied low, the serial I/O mode is active. The AD9854 serial port is a flexible, synchronous, serial communications port allowing easy interface to many industry-standard microcontrollers and microprocessors. The serial I/O is compatible with most synchronous transfer formats, including both the Motorola 6905/11 SPI and Intel 8051 SSR protocols. The interface allows read/write access to all twelve registers that configure the AD9854 and can be configured as a single pin I/O (SDIO) or two unidirectional pins for in/out (SDIO/SDO). Data transfers are supported in most significant bit (MSB) first format or least significant bit (LSB) first format at up to 10 MHz. When configured for serial I/O operation, most pins from the AD9854 parallel port are inactive; some are used for the serial I/O. Table VI describes pin requirements for serial I/O. Table VI. Serial I/O Pin Requirements Pin Number Pin Name 1, 2, 3, 4, 5, 6, 7, 8 14, 15, 16 D[7:0] A[5:3] 17 18 19 20 A2 A1 A0 I/O UD 21 22 WRB RDB Serial I/O Description The parallel data pins are not active, tie to VDD or GND. The parallel address Pins A5, A4, A3 are not active, tie to VDD or GND. IO RESET SDO SDIO Update Clock. Same functionality for Serial Mode as Parallel Mode. SCLK CSB--Chip Select Serial Register Address Register Name Number of Bytes Transferred 0 1 2 3 4 5 6 7 8 9 A B Phase Offset Tuning Word Register #1 Phase Offset Tuning Word Register #2 Frequency Tuning Word #1 Frequency Tuning Word #2 Delta Frequency Register Update Clock Rate Register Ramp Rate Clock Register Control Register I Path Digital Multiplier Register Q Path Digital Multiplier Register Shaped On/Off Keying Ramp Rate Register Q DAC Register 2 Bytes 2 Bytes 6 Bytes 6 Bytes 6 Bytes 4 Bytes 3 Bytes 4 bytes 2 Bytes 2 Bytes 2 Bytes 2 Bytes At the completion of any communication cycle, the AD9854 serial port controller expects the next eight rising SCLK edges to be the instruction byte of the next communication cycle. In addition, an active high input on the IO RESET pin immediately terminates the current communication cycle. After IO RESET returns low, the AD9854 serial port controller requires the next eight rising SCLK edges to be the instruction byte of the next communication cycle. All data input to the AD9854 is registered on the rising edge of SCLK. All data is driven out of the AD9854 on the falling edge of SCLK. Figures 51 and 52 are useful in understanding the general operation of the AD9854 Serial Port. CS GENERAL OPERATION OF THE SERIAL INTERFACE There are two phases to a communication cycle with the AD9854. Phase 1 is the instruction cycle, which is the writing of an instruction byte into the AD9854, coincident with the first eight SCLK rising edges. The instruction byte provides the AD9854 serial port controller with information regarding the data transfer cycle, which is Phase 2 of the communication cycle. The Phase 1 instruction byte defines whether the upcoming data transfer is read or write, and the register address in which to transfer data to/from. The first eight SCLK rising edges of each communication cycle are used to write the instruction byte into the AD9854. The remaining SCLK edges are for Phase 2 of the communication cycle. Phase 2 is the actual data transfer between the AD9854 and the system controller. The number of data bytes transferred in Phase 2 of the communication cycle is a function of the register address. The AD9854 internal serial I/O controller expects every byte of the register being accessed to be transferred. Table VII describes how many bytes must be transferred. -28- INSTRUCTION BYTE DATA BYTE 1 DATA BYTE 2 DATA BYTE 3 SDIO INSTRUCTION CYCLE DATA TRANSFER Figure 51. Using SDIO as a Read/ Write Transfer CS INSTRUCTION BYTE SDIO INSTRUCTION CYCLE DATA TRANSFER DATA BYTE 1 DATA BYTE 2 DATA BYTE 3 SDO DATA TRANSFER Figure 52. Using SDIO as an Input, SDO as an Output REV. 0 AD9854 Instruction Byte The instruction byte contains the following information. Table VIII. Instruction Byte Information MSB D6 D5 D4 D3 D2 D1 LSB R/W X X X A3 A2 A1 A0 R/W--Bit 7 of the instruction byte determines whether a read or write data transfer will occur after the instruction byte write. Logic high indicates read operation. Logic zero indicates a write operation. Bits 6, 5, and 4 of the instruction byte are don't care. A3, A2, A1, A0--Bits 3, 2, 1, 0 of the instruction byte determine which register is accessed during the data transfer portion of the communications cycle. See Table VIII for register address details. SERIAL INTERFACE PORT PIN DESCRIPTION SCLK Serial Clock (Pin 21). The serial clock pin is used to synchronize data to and from the AD9854 and to run the internal state machines. SCLK maximum frequency is 10 MHz. The system must maintain synchronization with the AD9854 or the internal control logic will not be able to recognize further instructions. For example, if the system sends the instruction to write a 2-byte register, then pulses the SCLK pin for a 3-byte register (24 additional SCLK rising edges), communication synchronization is lost. In this case, the first 16 SCLK rising edges after the instruction cycle will properly write the first two data bytes into the AD9854, but the next eight rising SCLK edges are interpreted as the next instruction byte, NOT the final byte of the previous communication cycle. In the case where synchronization is lost between the system and the AD9854, the IO RESET pin provides a means to reestablish synchronization without reinitializing the entire chip. Asserting the IO RESET pin (active high) resets the AD9854 serial port state machine, terminating the current IO operation and putting the device into a state in which the next eight SCLK rising edges are understood to be an instruction byte. The SYNC IO pin must be deasserted (low) before the next instruction byte write can begin. Any information that had been written to the AD9854 registers during a valid communication cycle prior to loss of synchronization will remain intact. tPRE CS Chip Select (Pin 22). Active low input that allows more than one device on the same serial communications lines. The SDO and SDIO pins will go to a high impedance state when this input is high. If driven high during any communications cycle, that cycle is suspended until CS is reactivated low. Chip Select can be tied low in systems that maintain control of SCLK. SDIO tSCLK CS tDSU tSCLKPWH tSCLKPWL SCLK tDHLD SDIO Serial Data I/O (Pin 19). Data is always written into the AD9854 on this pin. However, this pin can be used as a bidirectional data line. The configuration of this pin is controlled by Bit 0 of register address 20h. The default is logic zero, which configures the SDIO pin as bidirectional. 1ST BIT SYMBOL TPRE TSCLK TDSU TSCLKPWH TSCLKPWL TDHLD SDO Serial Data Out (Pin 18). Data is read from this pin for protocols that use separate lines for transmitting and receiving data. In the case where the AD9854 operates in a single bidirectional I/O mode, this pin does not output data and is set to a high impedance state. 2ND BIT MIN DEFINITION 30ns 100ns 30ns 40ns 40ns 0ns CS SETUP TIME PERIOD OF SERIAL DATA CLOCK SERIAL DATA SETUP TIME SERIAL DATA CLOCK PULSEWIDTH HIGH SERIAL DATA CLOCK PULSEWIDTH LOW SERIAL DATA HOLD TIME Figure 53. Timing Diagram for Data Write to AD9854 CS IO RESET Synchronize I/O Port (Pin 17). Synchronizes the I/O port state machines without affecting the addressable registers contents. An active high input on IO RESET pin causes the current communication cycle to terminate. After IO RESET returns low (Logic 0) another communication cycle may begin, starting with the instruction byte write. SCLK SDIO SDO 2ND BIT tDV NOTES ON SERIAL PORT OPERATION SYMBOL TDV The AD9854 serial port configuration bits reside in Bits 1 and 0 of register address 20h. It is important to note that the configuration changes immediately upon a valid I/O update. For multibyte transfers, writing this register may occur during the middle of a communication cycle. Care must be taken to compensate for this new configuration for the remainder of the current communication cycle. REV. 0 1ST BIT MAX DEFINITION 30ns DATA VALID TIME Figure 54. Timing Diagram for Read from AD9854 -29- AD9854 IR WRITE PHASE DATA TRANSFER - TWO BYTE WRITE CS SCLK 10 SDIO 11 12 13 14 15 16 17 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 Figure 55. Data Write Cycle, SCLK Idle High IR WRITE PHASE DATA TRANSFER - TWO BYTE READ CS SCLK SDIO 10 11 SDO 12 13 14 15 16 17 B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 Figure 56. Data Read Cycle, 3-Wire Configuration, SCLK Idle Low MSB/LSB TRANSFERS The AD9854 serial port can support both most significant bit (MSB) first or least significant bit (LSB) first data formats. This functionality is controlled by Bit 1 of serial register bank 20h. When this bit is set active high, the AD9854 serial port is in LSB first format. This bit defaults low, to the MSB first format. The instruction byte must be written in the format indicated by Bit 1 of serial register bank 20h. That is, if the AD9854 is in LSB first mode, the instruction byte must be written from least significant bit to most significant bit. Update Clock Operation Programming the AD9854 is asynchronous to the system clock with all data being stored in a buffer memory that does not immediately affect the part operation. The buffer memory is transferred to the register bank synchronous to system clock. The register bank information affects part operation. This transfer of data can occur automatically, with frequency of updates programmable by the user, or can occur completely under user control. Complete user control, referred to as external update mode, allows the user to drive the I/O UD signal from their ASIC or DSP. The AD9854 I/O UD pin is configured as an input in external update mode. A rising edge on I/O UD indicates to the AD9854 that the contents of the buffer memory is to be transferred to the register bank. The design uses an edge detector to signal the AD9854 to transfer data which allows a very small minimum high pulse width requirement (two system clock periods). Its important to note that if the user keeps I/O UD high, the AD9854 will NOT continuously update the register bank. Internal update mode, in which the AD9854 transfers data from the buffer memory to the register bank automatically, configures the AD9854 I/O UD pin as an output. The AD9854 generates a high pulse on I/O UD pin to signal the user that the buffer memory has just been transferred to the register bank. The minimum high pulsewidth is designed to be eight system clock cycles (min). The I/O UD signal can be used as an interrupt within the system. Its important to note that as an output I/O UD pin will not have anything approaching a 50/50 duty cycle for slower update rates. Programming the Update Clock register for values less than five will cause the I/O UD pin to remain high. The update clock functionality still works, its just that the user cannot use the signal as an indication that data is transferring. This is an affect of the minimum high pulse time when I/O UD is an output. For internal update clock operation, the rate which the updates occur is programmed into the update clock register. The update clock register is 32 bits and the value written into the register corresponds to HALF the number of clock cycles between updates. That is, if a value of 00_00_00_0A (hex), is written into the update clock register the rising edge of the I/O UD pin will occur every 20 cycles (0A hex equals 10 decimal). CONTROL REGISTER The Control Register is located in the shaded portion of the Table V at address 1D through 20 hex. It is composed of 32 bits. Bit 31 is located at the top left position and Bit 0 is located in the lower right position of the shaded table portion. The register has been subdivided below to make it easier to locate the text associated with specific control categories. -30- REV. 0 AD9854 Power-Down Functions Four bits are available to power down the AD9854. Each bit is active high, that is, they default low and a Logic 1 causes the power-down function to be working, The four bits all reside in the same control byte such that one IO write cycle can complete a full power-down by writing all four bits true simultaneously. The four bits are located in Control Register [28, 26:24] and are described below. The default state for these bits is Logic 0, inactive. CR[31:29] are open. CR[28] is the comparator power-down bit. When set (Logic 1), this signal indicates to the comparator that a power-down mode is active. This bit is an output of the digital section and is an input to the analog section. CR[27] must always be written to logic zero. Writing this bit to Logic 1 causes the AD9854 to stop working until a master reset is applied. CR[26] is the Q DAC power-down bit. When set (Logic 1), this signal indicates to the Q DAC that a power-down mode is active. CR[25] is the full DAC power-down bit. When set (Logic 1), this signal indicates to both the I and Q DACs as well as the reference that a power-down mode is active. CR[24] is the digital power-down bit. When set (Logic 1), this signal indicates to the digital section that a power-down mode is active. Within the digital section, the clocks will be forced to dc, effectively powering down the digital section. The REFCLK input will still be seen by the PLL and the PLL will continue to output the higher frequency. REFCLK Multiplier PLL Functions frequency sweep pattern with very little (or no) user input required. This bit is intended for chirp mode only, but there is no logic to suppress its functionality in other modes. CR[14] is the clear accumulator bit. This bit, active high, holds both the accumulator 1 and accumulator 2 values at zero for as long as the bit is active. This allows the DDS phase to be initialized via the I/O port. CR[13] is the triangle bit. When this bit is set, the AD9854 will automatically perform a continuous frequency sweep from F1 to F2 frequencies and back. The effect is a triangular frequency sweep. When this bit is set, the operating mode must be set to ramped FSK. CR[12] is the source Q DAC bit on the AD9854 only. When set, the Q path DAC accepts data from the QDAC Register. For the AD9854, this bit does not require a Logic 1 as the only data available to the Q path DAC is from the QDAC Register. CR[11:9] are the three bits that describe the five operating modes of the AD9854: 0h = Single-Tone Mode 1h = FSK Mode 2h = Ramped FSK mode 3h = Chirp Mode 4h = PSK Mode CR[8] is the internal update active bit. When this bit is set to Logic 1, the I/O UD pin is an output and the AD9854 generates the I/O UD signal. When Logic 0, external I/O UD functionality is performed, the I/O UD pin is configured as an input. CR[7] is reserved. Write to zero. CR[23] is reserved. Write to zero. CR[6] is the bypass of the inverse sinc filter bit. When set, the data from the DDS block goes directly to the output shapedkeying logic and the clock to the inverse sinc filter is stopped. Default is clear, filter enabled. CR[22] is the PLL range bit. The PLL range bit controls the VCO gain. The power-up state of the PLL range bit is Logic 1, higher gain for frequencies above 200 MHz. CR[5] is the shaped keying enable bit. When set the output ramping function is enabled and is performed in accordance with the CR[4] bit requirements. CR[21] is the bypass PLL bit, active high. When active, the PLL is powered down and the REFCLK input is used to drive the system clock signal. The power-up state of the bypass PLL bit is Logic 1, PLL bypassed. CR[4] is the internal/external output shaped-keying control bit. When set Logic 1, the shaped-keying factor will be internally generated and applied to both the I and Q paths. When clear, the output shaped-keying function is externally controlled by the user and the shaped-keying factor is the I and Q output shaped-keying factor register values. Defaults low external shapedkeying factors used. The two registers that are the shaped-keying factors also default low such that the output is off at power-up and until the device is programmed by the user. Seven control register bits, located in the Control Register [22:16] positions, relate to the PLL. CR[20:16] bits are the PLL multiplier factor. These bits are the REFCLK multiplication factor unless the bypass PLL bit is set. The PLL multiplier valid range is from 4 to 20, inclusive. Other Operational Functions CR[15] is the clear accumulator 1 bit. This bit has a one-shot type function. When written active, Logic 1, a clear accumulator 1 signal is sent to the DDS logic, resetting the accumulator value to zero. The bit is then automatically reset, but the buffer memory is not reset. This bit allows the user to easily create a sawtooth REV. 0 CR[3:2] are reserved. Write to zero. CR[1] is the serial port MSB/LSB first bit. Defaults low, MSB first. CR[0] is the serial port SDO active bit. Defaults low, inactive. -31- AD9854 JUNCTION TEMPERATURE CONSIDERATIONS POWER DISSIPATION AND THERMAL CONSIDERATIONS The AD9854 is a multifunctional, very high-speed device that targets a wide variety of synthesizer and agile clock applications. The set of numerous innovative features contained in the device each consume incremental power, the sum of which, if enabled in combination, may exceed the safe thermal operating conditions of the device. Careful analysis and consideration of power dissipation and thermal management is a critical element in the successful application of the AD9854 device. The AD9854 device is specified to operate within the industrial temperature range of -40C to +85C. This specification is conditional, however, such that the absolute maximum junction temperature of 150C is not exceeded. At high operating temperatures, extreme care must be taken in the operation of the device to avoid exceeding the junction temperature which results in a potentially damaging thermal condition. Many variables contribute to the operating junction temperature within the device, including: 1. Package Style 2. Selected Mode of Operation 3. Internal System Clock Speed 4. Supply Voltage 5. Ambient Temperature. The power dissipation (PDISS) of the AD9854 device in a given application is determined by many operating conditions. Some of the conditions have a direct relationship with PDISS, such as supply voltage and clock speed, but others are less deterministic. The total power dissipation within the device, and its effect on the junction temperature, must be considered when using the device. The junction temperature of the device is given by: Junction Temperature = (Thermal Impedance x Power Consumption) + Ambient Temperature Given that the junction temperature should never exceed 150C for the AD9854, and that the ambient temperature can be 85C, the maximum power consumption for the AD9854AST is 1.7 W and the AD9854ASQ (thermally-enhanced package) is 4.1 W. Factors affecting the power dissipation are: Supply Voltage--this obviously affects power dissipation and junction temperature since PDISS equals V x I. Users should design for 3.3 V nominal; however, the device is guaranteed to meet specifications, over the full temperature range and over the supply voltage range of 3.135 V to 3.465 V. Clock Speed--this directly and linearly influences the total power dissipation of the device, and, therefore, junction temperature. As a rule, the user should always select the lowest internal clock speed possible to support a given application, to minimize power dissipation. Normally the usable frequency output bandwidth from a DDS is limited to 40% of the clock rate to keep reasonable requirements on the output low-pass filter. For the typical DDS application, the system clock frequency should be 2.5 times the highest desired output frequency. The combination of these variables determines the junction temperature within the AD9854 device for a given set of operating conditions. The AD9854 device is available in two package styles: a thermallyenhanced surface-mount package with an exposed heat sink, and a nonthermally-enhanced surface-mount package. The thermal impedance of these packages is 16C/W and 38C/W respectively, measured under still-air conditions. THERMAL IMPEDANCE The thermal impedance of a package can be thought of as a thermal resistor that exists between the semiconductor surface and the ambient air. The thermal impedance of a package is determined by package material and its physical dimensions. The dissipation of the heat from the package is directly dependent upon the ambient air conditions and the physical connection made between the IC package and the PCB. Adequate dissipation of power from the AD9854 relies upon all power and ground pins of the device being soldered directly to a copper plane on a PCB. In addition, the thermally-enhanced package of the AD9854ASQ contains a heat sink on the bottom of the package that must be soldered to a ground pad on the PCB surface. This pad must be connected to a large copper plane which, for convenience, may be ground plane. Sockets for either package style of the AD9854 device are not recommended. Mode of Operation--the selected mode of operation for the AD9854 has a great influence on total power consumption. The AD9854 offers many features and modes, each of which imposes an additional power requirement. The collection of features contained in the AD9854 target a wide variety of applications and the device was designed under the assumption that only a few would be enabled for any given application. In fact, the user must understand that enabling multiple features at higher clock speeds may cause the junction temperature of the die to be exceeded. This can severely limit the long-term reliability of the device. Figure 57 provides a summary of the power requirements associated with the individual features of the AD9854. This table should be used as a guide in determining the optimum application of the AD9854 for reliable operation. As can be seen in the Figure 57, the Inverse Sinc filter function requires a significant amount of power, and much forethought and scrutiny should be given to its use. As an alternate approach to maintaining flatness across the output bandwidth, the digital Multiplier function may be used to adjust the output signal level, at a dramatic savings in power consumption. Careful planning and management in the use of the feature set will minimize power dissipation and avoid exceeding junction temperature requirements within the IC. -32- REV. 0 AD9854 EVALUATION OF OPERATING CONDITIONS 1400 The first step in applying the AD9854 is to select the internal clock frequency. Clock frequency selections above 200 MHz will require the thermally-enhanced package (AD9854ASQ); clock frequency selections of 200 MHz and below may allow the user to use the standard plastic surface-mount package, but more information will be needed to make that determination. 1200 SUPPLY CURRENT - mA ALL CIRCUITS ENABLED 1000 800 600 400 200 BASIC CONFIGURATION 0 20 60 100 140 180 220 FREQUENCY - MHz 260 300 Figure 57a. Current Consumption vs. Clock Frequency Figure 57a shows the supply current consumed by the AD9854 over a range of frequencies for two possible configurations: all circuits enabled means the output scaling multipliers, the inverse sinc filter, the Q DAC, and the on-board comparator are all enabled. Basic configuration means the output scaling multipliers, the inverse sinc filter, the Q DAC, and the on-board comparator are all disabled. 500 The third step is to divide this maximum rise number by the thermal impedance, to arrive at the maximum power dissipation allowed for the application. For the example so far, 65C divided by both versions of the AD9854 package's thermal impedances of 38C/W and 16C/W, yields a total power dissipation limit of 1.7 W and 4.1 W (respectively). This means that for a 3.3 V nominal power supply voltage, the current consumed by the device under full operating conditions must not exceed 515 mA in the standard plastic package and 1242 mA in the thermally-enhanced package. The total set of enabled functions and operating conditions of the AD9854 application must support these current consumption limits. INVERSE SINC FILTER 450 Figures 57a and Figure 57b may be used to determine the suitability of a given AD9854 application vs. power dissipation requirements. These graphs assume that the AD9854 device will be soldered to a multilayer PCB per the recommended best manufacturing practices and procedures for the given package type. This ensures that the specified thermal impedance specifications will be achieved. 400 SUPPLY CURRENT - mA The second step is to determine the maximum required operating temperature for the AD9854 in the given application. Subtract this value from 150C, which is the maximum junction temperature allowed for the AD9854. For the extended industrial temperature range of 85C, the result will be 65C. This is the maximum rise in temperature that the junction may experience due to power dissipation. 350 300 250 OUTPUT SCALING MULTIPLIERS 200 150 100 Q DAC COMPARATOR 50 0 1 2 3 4 5 6 FREQUENCY - MHz 7 8 Figure 57b. Current Consumption by Function vs. Clock Frequency Figure 57b shows the approximate current consumed by each of four functions. REV. 0 -33- AD9854 THERMALLY ENHANCED PACKAGE MOUNTING GUIDELINES The following are general recommendations for mounting the thermally enhanced exposed heat sink package (AD9854ASQ) to printed circuit boards. The exceptional thermal characteristics of this package depend entirely upon proper mechanical attachment. Figure 58 depicts the package from the bottom and shows the dimensions of the exposed heat sink. A solid conduit of solder needs to be established between this pad and the surface of the PCB. 14mm U NT RY CO 10mm The thermal land itself must be able to distribute heat to an even larger copper plane such as an internal ground plane. Vias must be uniformly provided over the entire thermal pad to connect to this internal plane. A proposed via pattern is shown in Figure 60. Via holes should be small (12 mils, 0.3 mm) such that they can be plated and plugged. These will provide the mechanical conduit for heat transfer. Figure 60. Figure 58. Figure 59 depicts a general PCB land pattern for such an exposed heat sink device. Note that this pattern is for a 64-lead device not an 80-lead, but the relative shapes and dimensions still apply. In this land pattern, a solid copper plane exists inside of the individual lands for device leads. Note also that the solder mask opening is conservatively dimensioned to avoid any assembly problems. Finally, a proposed stencil design is depicted for screen solder placement. Note that if vias are not plugged, wicking will occur which will displace solder away from the exposed heat sink and the necessary mechanical bond will not be established. SOLDER MASK OPENING THERMAL LAND Figure 61. Figure 59. -34- REV. 0 AD9854 EVALUATION BOARD An evaluation board is available that supports the AD9854 DDS devices. This evaluation board consists of a PCB, software, and documentation to facilitate bench analysis of the performance of the AD9854 device. It is recommended that users of the AD9854 familiarize themselves with the operation and performance capabilities of the device with the evaluation board. The evaluation board should also be used as a PCB reference design to ensure optimum dynamic performance from the device. OPERATING INSTRUCTIONS To assist in proper placement of the pin-header shorting-jumpers, the instructions will refer to direction (left, right, top, bottom) as well as header pins to be shorted. Pin #1 for each three pinheader has been marked on the PCB corresponding with the schematic diagram. When following these instructions, position the PCB so that the text can be read from left to right. The board is shipped with the pin-headers configuring the board as follows: 1. REFCLK for the AD9854 is configured as differential. The differential clock signals are provided by the 100LVEL16 differential receiver. 2. Input clock for the 100LVEL16 is single-ended via J5. This signal may be 3.3 V CMOS or a 2 V p-p sine wave capable of driving 50 (R8). 3. Both DAC outputs from the AD9854 are routed through the two 120 MHz elliptical LP filters and their outputs connected to J3 (Q) and J4 (I). 4. The board is set up for software control via the printer port connector. 5. Configured for AD9854 operation. Load the software from the CD onto the host PC's hard disk. Only Windows 9X and NT operating system are supported. Connect a printer cable from the PC to the AD9854 Evaluation Board printer port connector labeled "J11." Attach power wires to connector labeled "TB1" using the screwdown terminals. This is a plastic connector that press-fits over a 4-pin header soldered to the board. Table IX below shows connections to each pin. DUT = "device under test." Table IX. Power Requirements for DUT Pins AVDD 3.3 V for All DUT Analog Pins DVDD 3.3 V for All DUT Digital Pins VCC 3.3 V for All Other Devices Ground --for All Devices Attach REFCLK There are three possibilities to choose from: 1. On-Board (But Optional) Crystal Clock Oscillator, Y1. Insert an appropriate 3.3 V CMOS clock oscillator. See that the shorting jumper at W5 is located on Pins 1 and 2 (the left two pins). This routes the single-ended oscillator output to a very high speed "Differential Receiver" (the MC100LVEL16), where the signal is transformed to a differential PECL output. To route the differential output signals to AD9854, two more switches must be configured. W9 must have a shorting jumper on Pins 2 and 3 (the right two pins). To engage the differential clocking mode of the AD9854 W3, Pins 2 and 3 (the right two pins) must be connected with a shorting jumper. REV. 0 2. External Differential Clock Input, J5. This is actually just another single-ended input that will be routed to the MC100LVEL16 for conversion to differential PECL output. This is accomplished by attaching a 2 V p-p clock or sine wave source to J5. Note that this is a 50 impedance point set by R8. The input signal will be ac-coupled and then biased to the center switching threshold of the MC100LVEL16. Position the shorting jumper of W5 to Pins 2 and 3 (the right two pins) to route the signal at J5 to the differential receiver IC. To route the differential output signals to AD9854, two more switches must be configured. W9 must have a shorting jumper on Pins 2 and 3 (the right two pins). To engage the differential clocking mode of the AD9854 W3, Pins 2 and 3 (the right two pins) must be connected with a shorting jumper. 3. External Single-Ended Clock Input, J7. This mode bypasses the MC100LVEL16 and directly drives the AD9854 with your reference clock. Attach a 50 , 2 V p-p sine source that is dc offset to 1.65 V, or a 50 CMOS-level clock source to J7. Remove the shorting jumper from W5 altogether to make certain that the device (U3) Is not Toggling or Self-Oscillating. Set the shorting jumper at W9 on Pins 1 and 2 (the left two pins) to route the REFCLK signal from J7 to Pin 69 of the AD9854. Finally, set the shorting jumper at W3 to Pins 1 and 2 (the left two pins) to place the AD9854 in the single-ended clock mode. Regardless of the origination, the signals arriving at the AD9854 are called the Reference Clock. If you choose to engage the on-chip REFCLK Multiplier, this signal is the reference clock for the REFCLK Multiplier and the REFCLK Multiplier output becomes the SYSTEM CLOCK. If you choose to bypass the REFCLK Multiplier, the reference clock that you have supplied is directly operating the AD9854 and is, therefore, the system clock. Three-state control or switch headers W11, W12, W14, and W15 must be shorted to allow the provided software to control the AD9854 evaluation board via the printer port connector J11. If programming of the AD9854 is not to be provided by the host PC via the ADI software, then headers W11, W12, W14, and W15 should be opened (shorting jumpers removed). This effectively detaches the PC interface and allows the 40-pin header, J10, to assume control without bus contention. Input signals on J10 going to the AD9854 should be 3.3 V CMOS logic levels. Low-Pass Filter Testing The purpose of 2-pin headers W7 and W10 (associated with J1 and J2) are to allow the two 50 , 120 MHz filters to be tested during PCB assembly without interference from other circuitry attached to the filter inputs. Normally, a shorting jumper will be attached to each header to allow the DAC signals to be routed to the filters. If the user wishes to test the filters, the shorting jumpers at W7 and W10 should be removed and 50 test signals applied at J1 and J2 inputs to the 50 elliptic filters. User should refer to Figure 62 and the following sections to properly position the remaining shorting jumpers. -35- AD9854 1. Install shorting jumpers at W7 and W10. Observing the Unfiltered IOUT1 and the Unfiltered IOUT2 DAC Signals This allows the viewer to observe the unfiltered DAC outputs at J2 (the "I" signal) and J1 (the "Q" signal). The procedure below simply routes the two 50 terminated analog DAC outputs to the BNC connectors and disconnects any other circuitry. The "raw" DAC outputs will be a series of quantized (stepped) output levels. The default 10 mA output current will develop a 0.5 V p-p signal across the on-board 50 termination. When connected to an external 50 input, the DAC will therefore develop 0.25 V p-p due to the double termination. 1. Install shorting jumpers at W7 and W10. 2. Remove shorting jumper at W16. 3. Remove shorting jumper from 3-pin header W1. 4. Install shorting jumper on Pins 1 and 2 (bottom two pins) of 3-pin header W4. Observing the Filtered IOUT1 and the Filtered IOUT2 This allows viewer to observe the filtered I and Q DAC outputs at J4 (the "I" signal) and J3 (the "Q" signal). This places the 50 (input and output Z) low-pass filters in the I and Q DAC pathways to remove images and aliased harmonics and other spurious signals above the dc to approximately 120 MHz bandpass. These signals will appear as nearly pure sine waves and exactly 90 degrees out-of-phase with each other. These filters are designed with the assumption that the system clock speed is at or near maximum (300 MHz). If the system clock utilized is much less than 300 MHz, for example 200 MHz, unwanted DAC products other than the fundamental signal will be passed by the low-pass filters. 1. Install shorting jumpers at W7 and W10. 2. Install shorting jumper at W16. 3. Install shorting jumper on Pins 1 and 2 (bottom two pins) of 3-pin header W1. 4. Install shorting jumper on Pins 1 and 2 (bottom two pins) of 3-pin header W4. 5. Install shorting jumper on Pins 1 and 2 (top two pins) of 3pin header W2 and W8. Observing the Filtered I OUT and the Filtered IOUTB This allows viewer to observe only the filtered "I" DAC outputs at J4 (the "true" signal) and J3 (the "complementary" signal). This places the 120 MHz low pass filters in the true and complementary output paths of the I DAC to remove images and aliased harmonics and other spurious signals above approximately 120 MHz. These signals will appear as nearly pure sine waves and exactly 180 degrees out-of-phase with each other. Again, if the system clock used is much less than 300 MHz, for example 200 MHz, then unwanted DAC products other than the fundamental signal will be passed by the low-pass filters. 2. Install shorting jumper at W16. 3. Install shorting jumper on Pins 2 and 3 (top two pins) of 3pin header W1. 4. Install shorting jumper on Pins 2 and 3 (top two pins) of 3pin header W4. 5. Install shorting jumper on Pins 1 and 2 (top two pins) of 3pin header W2 and W8. To connect the high-speed comparator to the DAC output signals choose either the quadrature filtered output configuration or the complementary filtered output configuration as outlined above. Follow Steps 1 through 4 above, for the desired filtered configuration. Step 5 below will reroute the filtered signals away from their connectors (J3 and J4) and connect them to the 100 configured comparator inputs. This configures the comparator for differential input without control of the comparator output duty cycle. The comparator output duty cycle should be approximately 50% in this configuration. 5. Install shorting jumper on Pins 2 and 3 (bottom two pins) of 3-pin header W2 and W8. User may elect to change the RSET resistor, R2 from 3.9 k to 2 k to get a more robust signal at the comparator inputs. This will decrease jitter and extend comparator operating range. This can be accomplished by soldering a second 3.9 k chip resistor in parallel with the provided R2. Connecting the High-Speed Comparator in a Single-Ended Configuration This will allow duty cycle or pulse width control and requires that a dc threshold voltage be present at one of the comparator inputs. You may supply this voltage using the "Q DAC" by configuring it as a control DAC in software or by removing the shorting jumper at 2-pin header W6. A 12-bit, twos-complement value is written to the Q-DAC register that will set the IOUT2 output to a static dc level. Allowable hexadecimal values are 7FF (maximum) to 800 (minimum) with all 0s being midscale. The IOUT1 channel will continue to output a filtered sine wave programmed by the user. These two signals are routed to the comparator inputs using W2 and W8 3-pin header switches. The configuration described above entitled "Observing the Filtered I OUT and the Filtered I OUTB" must be used. Follow Steps 1 through 4 and then the following Step 5: 5. Install shorting jumper on Pins 2 and 3 (bottom two pins) of 3-pin header W2 and W8. User should elect to change the RSET resistor from 3900 to 1950 to get a more robust signal at the comparator inputs. This will decrease jitter and extend comparator operating range. User can accomplish this by soldering a second 3.9 k chip resistor in parallel with the provided R2. -36- REV. 0 AD9854 The control software for the AD9854/PCB evaluation board is provided on a CD. This brief set of instructions should be used in conjunction with the AD9854/PCB evaluation board schematic. Several numerical entries, such as frequency and phase information, require that the ENTER key by pressed to register that information. 1. Select the proper printer port. Click the "Parallel Port" selection in the menu bar. Select the port that matches your PC. If unknown, experiment by performing the following on the selected port. With the part powered up, properly clocked and connected to the PC, select a port and go to the "Mode and Frequency" menu and click the "Reset DUT and Initialize Registers" button. Then go to the "Clock and Amplitude" menu. Once there, click the box next to "Bypass Inverse Sinc Filter" . . . a check mark will appear in the box . . . next click the button "Send Control Info to DUT." If the proper port has been selected, the supply current going to the AD9854/ PCB evaluation board should drop by approximately 1/3 when the inverse sinc filters are bypassed. Conversely, the supply current will increase approximately 1/3 when the inverse sinc filters are engaged. 4. The output amplitude defaults to the 12-bit straight binary multiplier values of the I and Q multiplier registers of 000hex and no output should be seen from the DACs. User should now set both multiplier amplitudes in the Output Amplitude window to a substantial value, such as FFFhex. You may bypass the digital multiplier by clicking the box "Output Amplitude is always Full-Scale" but experience has shown that doing so does not result in best SFDR. It is interesting to note that best SFDR, as much as 11 dB better, is obtained by routing the signal through the digital multiplier and "backing off" on the multiplier amplitude. For instance, FC0 hex produces less spurious signal amplitude than FFF hex. Its a repeatable phenomenon that should be investigated exploited for maximum SFDR (spurious-free dynamic range). 5. Refer to this data sheet and evaluation board schematic to understand all the functions of the AD9854 available to the user and to gain an understanding of what the software is doing in response to programming commands. Applications assistance is available for the AD9854, the AD9854/PCB evaluation board, and all other Analog Devices products. Please call 1/800-ANALOGD. 2. Normal operation of the AD9854/PCB evaluation board begins with a master reset. Many of the default register values after reset are depicted in the software "control panel." The reset command sets the DDS output amplitude to minimum and 0 Hz, 0 phase-offset as well as other states listed in the AD9854 Register Layout table in the preliminary data sheet. 3. The next programming block should be the "Reference Clock and Multiplier" since this information is used to determine the proper 48-bit frequency tuning words that will be entered and calculated later. REV. 0 -37- AD9854 Figure 62a. Evaluation Board Schematic -38- REV. 0 AD9854 Figure 62b. Evaluation Board Schematic REV. 0 -39- AD9854 Customer Evaluation Board REV C, Bill of Material # Quantity REFDES Device Package Value 1 2 5 23 Chip Cap Chip Cap 0805 0805 0.01 F 0.1 F 3 4 5 6 2 2 3 2 2 2 2 2 7 1 1 4 2 2 2 2 1 3 2 2 2 4 1 1 1 1 1 4 3 1 7 8 1 4 C1, C2, C35, C36, C45 C3, C7, C8, C9, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C22, C23, C24, C26, C27, C28, C29, C44 C4, C37 C5, C38 C6, C21, C25 C30, C39 C31, C40 C32, C41 C33, C42 C34, C43 J1, J2, J3, J4, J5, J6, J7 0805 0805 BCAPTAJD 0805 0805 0805 0805 0805 Conn PCB 40CONN Chip Ind Chip Ind RES_SM RES_SM RES_SM RES_SM RES_SM RES_SM RES_SM RES_SM RES_SM RP1 TB4 AD9854 74HC125A MC100LVEL1 74HC14 74HC574 36PINCONN JUMP3PIN 2PINJUMP XTAL PIN SOCK 0805 0805 TAJD 0805 0805 0805 0805 0805 BNC GS02669REVC SAM5-40 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 1206 SIP-10P TB4 80LQFP SO14 SO8NB SO14 SO20WB CONN SIP-3P 2PINJUMP COSC Amp 5-330808-6 27 pF 47 pF 10 F 39 pF 22 pF 2.2 pF 12 pF 8.2 pF 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 J10 L1, L2, L3, L5 L4, L6 R1, R5 R2, R20 R3, R7 R4 R6, R8, R19 R9, R10 R11, R14 R12, R13 R15, R16, R17, R18 RP1 TB U1 U2 U3 U4, U5, U6, U7 U8, U9, U10 U11 W1, W2, W3, W4, W5, W8, W9 W6, W7, W10, W11, W12, W14, W15, W16 Y1 -40- 68NH 82NH 51 3900 24 1300 50 100 160 260 10K 10K REV. 0 AD9854 Figure 63. Assembly Drawing Figure 64. Top Routing Layer, Layer 1 REV. 0 -41- AD9854 Figure 65. Power Plane Layer, Layer 2 Figure 66. Ground Plane Layer, Layer 3 -42- REV. 0 AD9854 Figure 67. Bottom Routing Layer, Layer 4 REV. 0 -43- AD9854 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 0.063 (1.60) MAX 0.030 (0.75) 0.024 (0.60) 0.018 (0.45) C3728-8-10/99 80-Lead LQFP_ED (SQ-80) 0.630 (16.00) BSC SQ 0.394 (10.00) REF SQ 0.551 (14.00) BSC SQ 80 60 SEATING PLANE 80 61 61 1 60 1 PIN 1 THERMAL SLUG TOP VIEW (PINS DOWN) COPLANARITY 0.004 (0.10) MAX BOTTOM VIEW 20 41 21 20 41 40 40 0.006 (0.15) 0.002 (0.05) 21 0.057 (1.45) 0.055 (1.40) 0.053 (1.35) 0.008 (0.20) 0.004 (0.09) 0.0256 (0.65) BSC 0.015 (0.38) 0.013 (0.32) 0.009 (0.22) 78 3.58 08 CONTROLLING DIMENSIONS IN MILLIMETERS. CENTER FIGURES ARE NOMINAL UNLESS OTHERWISE NOTED. 80-Lead LQFP (ST-80) 0.640 (16.25) SQ 0.620 (15.75) 0.553 (14.05) SQ 0.549 (13.95) 0.063 (1.60) MAX 0.030 (0.75) 0.020 (0.50) 80 1 61 60 SEATING PLANE 0.486 (12.35) TYP SQ TOP VIEW (PINS DOWN) 20 21 41 40 0.029 (0.73) 0.022 (0.57) -44- PRINTED IN U.S.A. 0.004 (0.10) MAX 0.006 (0.15) 0.002 (0.05) 0.057 (1.45) 0.053 (1.35) 0.014 (0.35) 0.010 (0.25) REV. 0