IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH WITH 3-STATE OUTPUTS AND 5 VOLT TOLERANT I/O FEATURES: DESCRIPTION: * Typical tSK(o) (Output Skew) < 250ps * ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) * VCC = 3.3V 0.3V, Normal Range * VCC = 2.7V to 3.6V, Extended Range W typ. static) * CMOS power levels (0.4 * All inputs, outputs, and I/O are 5V tolerant * Supports hot insertion * Available in SSOP and TSSOP packages The LVC16373A 16-bit transparent D-type latch is built using advanced dual metal CMOS technology. This high-speed, low-power latch is ideal for temporary storage of data. The LVC16373A can be used for implementing memory address latches, I/O ports, and bus drivers. The Output Enable and Latch Enable controls are organized to operate each device as two 8bit latches or one 16-bit latch. Flow-through organization of signal pins simplifies layout. All inputs are designed with hysteresis for improved noise margin. All pins of the LVC16373A can be driven from either 3.3V or 5V devices. This feature allows the use of this device as a translator in a mixed 3.3V/ 5V supply system. The LVC16373A has been designed with a 24mA output driver. This driver is capable of driving a moderate to heavy load while maintaining speed performance. DRIVE FEATURES: * High Output Drivers: 24mA * Reduced system switching noise APPLICATIONS: * 5V and 3.3V mixed voltage systems * Data communication and telecommunication systems FUNCTIONAL BLOCK DIAGRAM 1OE 1 2OE 24 1LE 48 2LE 25 2D1 36 1D1 47 D C Q 2 D 13 C Q 1Q1 2Q1 TO SEVEN OTHER CHANNELS TO SEVEN OTHER CHANNELS IDT and the IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE JULY 2015 1 (c) 2015 Integrated Device Technology, Inc. DSC-4624/6 IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol 48 Description Max VTERM Terminal Voltage with Respect to GND -0.5 to +6.5 V TSTG Storage Temperature -65 to +150 C 1LE IOUT DC Output Current -50 to +50 mA IIK IOK Continuous Clamp Current, VI < 0 or VO < 0 -50 mA ICC ISS Continuous Current through each VCC or GND 100 mA 1OE 1 1Q1 2 47 1D1 1Q2 3 46 1D2 GND 4 45 GND 1Q3 5 44 1D3 1Q4 6 VCC 7 42 VCC 1Q5 8 41 1D5 1Q6 9 40 1D6 GND 10 39 GND 1Q7 11 38 1D7 1Q8 12 37 1D8 2Q1 13 36 2D1 43 Unit NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 1D4 CAPACITANCE (TA = +25C, F = 1.0MHz) Parameter(1) Symbol Conditions Typ. Max. Unit CIN Input Capacitance VIN = 0V 4.5 6 pF COUT Output Capacitance VOUT = 0V 6.5 8 pF CI/O I/O Port Capacitance VIN = 0V 6.5 8 pF NOTE: 1. As applicable to the device type. 2Q2 14 35 2D2 GND 15 34 GND 2Q3 16 33 2D3 2Q4 17 32 2D4 VCC 18 31 VCC 2Q5 19 30 2D5 xLE Latch Enable Input (Active HIGH) 2Q6 20 29 2D6 xOE Output Enable Inputs (Active LOW) GND 21 28 GND xQx 3-State Outputs 2Q7 22 27 2D7 2Q8 23 26 2D8 2OE 24 25 2LE PIN DESCRIPTION Pin Names xDx Description Data Inputs FUNCTION TABLE(1) Inputs xDx SSOP/ TSSOP TOP VIEW xLE Outputs xOE xQx H H L H L H L L X L L Q(2) X X H Z NOTES: 1. H = HIGH Voltage Level X = Don't Care L = LOW Voltage Level Z = High-Impedance 2. Output level before the indicated steady-state input conditions were established. 2 IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Condition: TA = -40C to +85C Symbol VIH VIL Min. Typ.(1) Max. Unit VCC = 2.3V to 2.7V 1.7 -- -- V VCC = 2.7V to 3.6V 2 -- -- VCC = 2.3V to 2.7V -- -- 0.7 VCC = 2.7V to 3.6V -- -- 0.8 Parameter Input HIGH Voltage Level Input LOW Voltage Level Test Conditions V Input Leakage Current VCC = 3.6V VI = 0 to 5.5V -- -- 5 A IOZH High Impedance Output Current VCC = 3.6V VO = 0 to 5.5V -- -- 10 A IOZL (3-State Output pins) IOFF Input/Output Power Off Leakage VCC = 0V, VIN or VO 5.5V -- -- 50 A VIK Clamp Diode Voltage VCC = 2.3V, IIN = -18mA -- -0.7 -1.2 V VH ICCL ICCH ICCZ ICC Input Hysteresis Quiescent Power Supply Current VCC = 3.3V VCC = 3.6V VIN = GND or VCC -- -- 100 -- -- 10 mV A 3.6 VIN 5.5V(2) One input at VCC - 0.6V, other inputs at VCC or GND -- -- -- -- 10 500 A IIH IIL Quiescent Power Supply Current Variation NOTES: 1. Typical values are at VCC = 3.3V, +25C ambient. 2. This applies in the disabled state only. OUTPUT DRIVE CHARACTERISTICS Symbol VOH Test Conditions(1) Parameter Output HIGH Voltage VCC = 2.3V to 3.6V IOH = - 0.1mA VCC = 2.3V IOH = - 6mA VCC = 2.3V IOH = - 12mA VCC = 2.7V VCC = 3V VOL Output LOW Voltage Min. Max. Unit VCC - 0.2 -- V 2 -- 1.7 -- 2.2 -- 2.4 -- VCC = 3V IOH = - 24mA 2.2 -- VCC = 2.3V to 3.6V IOL = 0.1mA -- 0.2 VCC = 2.3V IOL = 6mA -- 0.4 IOL = 12mA -- 0.7 VCC = 2.7V IOL = 12mA -- 0.4 VCC = 3V IOL = 24mA -- 0.55 V NOTE: 1. VIH and VIL must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate VCC range. TA = - 40C to + 85C. 3 IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE OPERATING CHARACTERISTICS, VCC = 3.3V 0.3V, TA = 25C Symbol Parameter CPD Power Dissipation Capacitance per Latch Outputs enabled CPD Power Dissipation Capacitance per Latch Outputs disabled Test Conditions Typical Unit CL = 0pF, f = 10Mhz 39 pF 6 SWITCHING CHARACTERISTICS(1) VCC = 2.7V Symbol Parameter tPLH Propagation Delay tPHL xDx to xQx VCC = 3.3V 0.3V Min. Max. Min. Max. Unit -- 4.9 1.6 4.2 ns -- 5.3 2.1 4.6 ns -- 5.7 1.3 4.7 ns -- 6.3 2.5 5.9 ns ns tPLH Propagation Delay tPHL xLE to xQx tPZH Output Enable Time tPZL xOE to xQx tPHZ Output Disable Time tPLZ xOE to xQx tSU Set-up Time, data before LE HIGH or LOW 1.7 -- 1.7 -- tH Hold Time, data after LE HIGH or LOW 1.2 -- 1.2 -- ns tW Pulse Width LE HIGH 3.3 -- 3.3 -- ns Output Skew(2) -- -- -- 500 ps tSK(o) NOTES: 1. See TEST CIRCUITS AND WAVEFORMS. TA = - 40C to + 85C. 2. Skew between any two outputs of the same package and switching in the same direction. 4 IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC(1)= 3.3V0.3V VCC(1)= 2.7V VCC(2)= 2.5V0.2V Unit VLOAD 6 6 2 x Vcc V VIH 2.7 2.7 Vcc V VT 1.5 1.5 Vcc / 2 V VLZ 300 300 150 mV VHZ 300 300 150 mV CL 50 50 30 pF Pulse (1, 2) Generator VIN DISABLE tPZL OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH 500 CL DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. Switch VLOAD TIMING INPUT Disable High Enable High GND ASYNCHRONOUS CONTROL All Other Tests Open SYNCHRONOUS CONTROL tSK (x) tPLH2 VOH VT VOL tH tREM tSU tH LOW-HIGH-LOW PULSE VT tW HIGH-LOW-HIGH PULSE VT LVC Link tPHL2 Pulse Width tSK(x) = tPLH2 - tPLH1 or tPHL2 - tPHL1 Output Skew - tSK(X) tSU VIH VT 0V VIH VT 0V VIH VT 0V VIH VT 0V Set-up, Hold, and Release Times VOH VT VOL OUTPUT 2 VOH VOH-VHZ 0V VT 0V LVC Link VIH VT 0V tSK (x) tPHZ Enable and Disable Times DATA INPUT tPHL1 VLOAD/2 VOL+VLZ VOL NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. SWITCH POSITION Open Drain Disable Low Enable Low tPLZ VLOAD/2 VT LVC Link NOTES: 1. Pulse Generator for All Pulses: Rate 10MHz; tF 2.5ns; tR 2.5ns. 2. Pulse Generator for All Pulses: Rate 10MHz; tF 2ns; tR 2ns. Test VIH VT 0V CONTROL INPUT Test Circuit for All Outputs OUTPUT 1 VIH VT 0V ENABLE GND VOUT tPLH1 tPHL Propagation Delay LVC Link INPUT tPLH LVC Link D.U.T. RT tPHL OPPOSITE PHASE INPUT TRANSITION Open 500 tPLH OUTPUT VLOAD VCC VIH VT 0V VOH VT VOL SAME PHASE INPUT TRANSITION LVC Link NOTES: 1. For tSK(o) OUTPUT1 and OUTPUT2 are any two outputs. 2. For tSK(b) OUTPUT1 and OUTPUT2 are in the same bank. 5 IDT74LVC16373A 3.3V CMOS 16-BIT TRANSPARENT D-TYPE LATCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION X LVC XX Bus-Hold Temp. Range XX Family XX XXXX Device Type Package X Blank 8 Tube or Tray Tape and Reel PVG PAG Shrink Small Outline Package - Green Thin Shrink Small Outline Package - Green 373A 16-Bit Transparent D-Type Latch with 3-State Outputs 16 Double-Density, 24mA Blank No Bus-hold 74 -40C to +85C DATASHEET DOCUMENT HISTORY 07/28/2015 Pg. 6 Updated the ordering information by removing non RoHS parts and adding Tape and Reel information. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 6 for Tech Support: logichelp@idt.com