STEGO, Inc. · 1395 S. Marietta Parkway · Building 800 · Marietta, GA 30067
Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Thermal Management Products & Accessories for Enclosures
Photo: STEGO International Headquarters in Germany
Introduction
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
STEGO develops innovative products that heat, cool, ventilate, illuminate, and control tem-
perature and humidity for enclosed electronic control systems. STEGO products are reliable,
simple, high quality and cost effective.
We strive to solve electronic control packaging problems for our customers. From our manu-
facturing plants in Brazil, France, Germany and the United States, and sales offices in the
Czech Republic, Italy, the Netherlands, Poland, Spain, Sweden and the UK, we
successfully serve customers in over 52 countries around the world.
STEGO offers a wide range of products in various sizes and specifications to meet almost
any need, and the majority conform to UL and CE standards.
PRODUCTS: • PTC based enclosure heaters
• Fan heaters with PTC and resistance heating elements
• Temperature and humidity controls
• Explosion-proof heaters and thermostats for hazardous areas
• Filter fans and exhaust filters
• Enclosure lights and other accessories
With this broad range of products offered, STEGO is assisting customers in a variety of
industries with their applications.
INDUSTRIES: • Electrical and electronic control systems
• Telecommunications systems
• Traffic control systems
• Parking control systems
• Ticket dispensing machines
• Automatic Teller Machines (ATMs)
• Power generation including Wind and Solar
Technical Data
Regulating
FT 011 Tamperproof Thermostat
||
FT011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Compact design
Fixed set points
Color coded modules
DIN rail mountable
Tamperproof (Pre-set) Thermostat FTO 011
NC / opens on temperature rise (red module housing) - for regulating heaters or for switching
signal devices when temperature has fallen below the minimum value.
Tamperproof (Pre-set) Thermostat FTS 011
NO / closes on temperature rise (blue module housing) - for regulating filter fans, heat exchang-
ers, cooling devices or for switching signal devices when temperature limit has been exceeded.
Sensor element thermostatic bimetal
Contact type snap-action contact
Service life > 100,000 cycles
Max. switching capacity 10 A resistive / 2 A inductive @ AC 120 V
5 A resistive / 1.6 A inductive @ AC 250 V
DC 30 W
Max. inrush current AC 16 A for 10 sec.
Connection 2-pole term. for AWG 14 max. (2.5 mm²), torque 0.8 Nm max.
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature -40 to +176 °F (-40 to +80 °C)
Storage temperature -49 to +176 °F (-45 to +80 °C)
Dimensions 1.85 x 1.3 x 1.3” (47 x 33 x 33 mm)
Weight approx. 0.8 oz. (23 g)
Protection type IP20
Approvals UL File No. E164102, VDE
Part No. Contact Switch-off temperature Switch-on temperature
01160.0-00 NC - open on rise 59 °F / 15 °C (± 9 °F / 5 K tolerance) 41 °F / 5 °C (± 9 °F / 5 K tolerance)
01160.0-01 NC - open on rise 77 °F / 25 °C (± 9 °F / 5 K tolerance) 59 °F / 15 °C (± 9 °F / 5 K tolerance)
Switch-on temperature Switch-off temperature
01161.0-00 NO - close on rise 122 °F / 50 °C (± 11 °F / 6 K tolerance) 104 °F / 40 °C (± 12.6 °F / 7 K tolerance)
01161.0-01 NO - close on rise 140 °F / 60 °C (± 11 °F / 6 K tolerance) 122 °F / 50 °C (± 12.6 °F / 7 K tolerance)
01161.0-02 NO - close on rise 95 °F / 35 °C (± 11 °F / 6 K tolerance) 77 °F / 25 °C (± 12.6 °F / 7 K tolerance)
12
1.3” (33 mm)
1.85” (47 mm)
1.3” (33 mm)
NC (red) NO (blue) Wiring examples
FTO 011 ThermostatHeater FTS 011 Thermostat e.g. Fan FTS 011 Thermostat e.g. Signal Device
Technical Data
Regulating
KT 011 Small Thermostat
||
KT011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Compact design
Wide adjustment range
Color coded temperature dials
DIN rail mountable
Thermostat NC (normally closed)
Thermostat opens on temperature rise - for regulating heaters or for switching signal devices.
Comes with red temperature dial.
Thermostat NO (normally open)
Thermostat closes on temperature rise - for regulating filter fans and heat exchangers or for
switching signal devices. Comes with blue temperature dial.
Switching difference 12.6 °F ± 7 °F tolerance (7 K ± 4 K)
Sensor element thermostatic bimetal
Contact type snap-action contact
Service life > 100,000 cycles
Max. switching capacity 15 A resistive / 2 A inductive @ AC 120 V
10 A resistive / 2 A inductive @ AC 250 V
DC 30 W
Max. inrush current AC 16 A for 10 sec.
Connection 2-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (with wire end ferrule) - AWG 16 (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
(or for Exhaust Filter EF 118 Series)
Mounting position vertical
Operating / Storage temperature -49 to +176 °F (-45 to +80 °C)
Dimensions 2.4 x 1.3 x 1.7” (60 x 33 x 43 mm)
Weight approx. 1.4 oz. (40 g)
Protection type IP20
Setting range Part No. (NC) Part No. (NO) Approvals
+32 to +140 °F 01140.9-00 01141.9-00 UL File No. E164102, CSA, VDE
0 to +60 °C 01146.9-00 01147.9-00 UL File No. E164102, CSA, VDE
-10 to +50 °C 01142.0-00 N/A UL File No. E164102, CSA, VDE
+10 to +70 °C N/A 01149.9-00 UL File No. E164102, CSA, VDE
-15 to +45 °C 01157.0-00 01156.0-00 UL File No. E164102, CSA, VDE
+20 to +80 °C 01159.0-00 01158.0-00 UL File No. E164102, CSA, VDE
1.3” (33 mm)
1.7” (43 mm)
2.4” (60 mm)
NC (red) NO (blue) Wiring examples
KT 011 Thermostat Heater KT 011 Thermostat e.g. Fan KT 011 Thermostat e.g. Signal Device
Technical Data
Regulating
||
ST011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
ST 011 Compact Thumbwheel Thermostat
Switching difference 7 °F (4 K) ± 5.4 °F (3 K) tolerance
Sensor element thermostatic bimetal
Contact type snap-action contact
Service life > 100,000 cycles
Max. switching capacity 15 A resistive / 2 A inductive @ AC 120 V
10 A resistive / 2 A inductive @ AC 250 V
DC 30 W (DC 24-72 V)
Max. inrush current AC 16 A for 10 sec.
Connection 2-pole terminal for AWG 14 max. (2.5 mm²), torque 1 Nm max.
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +176 °F (-45 to +80 °C)
Max. storage humidity 90 %RH (non-condensing)
Dimensions 2.76 x 1.3 x 1.65” (70 x 33 x 42 mm)
Weight approx. 1.8 oz. (50 g)
Protection type IP20
Adjustable thumbwheel setting
Compact design
Small hysteresis
High switching capacity
DIN rail mountable
The ST 011 thermostat is an SPST regulator with a small hysteresis. The housing design
ensures optimized air circulation around the sensor element.
STO 011: NC / opens on temperature rise (red thumbwheel) - for regulating heaters or for
switching signal devices when temperature has fallen below the minimum value.
STS 011: NO / closes on temperature rise (blue thumbwheel) - for regulating filter fans, heat
exchangers, cooling devices or for switching signal devices when temperature limit has been
exceeded.
Part No. (NC) Part No. (NO) Setting range Approvals
01115.9-00 01116.9-00 32 to 140 °F UL File No. E164102, VDE
01115.0-00 01116.0-00 0 to 60 °C UL File No. E164102, VDE
Wiring example
ST 011 Thermostat Heater ST 011 Thermostat ST 011 Thermostat
e.g. Filter Fan e.g. Signal Device
NC (red) NO (blue)
Enclosure heater
Filter fan, cooling equipment, signal device
Convenient minimum set-
point symbol on the NC
thermostat to assure
enclosure temperature
remains above freezing
Technical Data
2.5” (63 mm)
1.3” (33 mm)
1.85” (47 mm)
Regulating
FTD 011 Tamperproof Dual Thermostat
||
FTD011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
NC / NO or NO / NO in one unit
Fixed set points
Color coded modules
DIN rail mountable
Sensor element thermostatic bimetal
Contact type snap-action contact
Service life > 100,000 cycles
Max. switching capacity 10 A resistive / 2 A inductive @ AC 120 V
5 A resistive / 1.6 A inductive @ AC 250 V
DC 30 W
Max. inrush current AC 16 A for 10 sec.
Connection 4-pole term. for AWG 14 max. (2.5 mm²), torque 0.8 Nm max.
Housing plastic according to UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature -40 to +176 °F (-40 to +80 °C)
Storage temperature -49 to +176 °F (-45 to +80 °C)
Dimensions 1.85 x 2.5 x 1.3” (47 x 63 x 33 mm)
Weight approx. 1.41 oz. (40 g)
Protection type IP20
Approvals UL File No. E164102, VDE
Part No. NC - open on rise NO - close on rise
Switch-off temperature Switch-on temperature Switch-on temperature Switch-off temperature
01163.0-00 59 °F / 15 °C (± 9 °F / 5 K tolerance) 41 °F / 5 °C (± 9 °F / 5 K tolerance) 122 °F / 50 °C (± 11 °F / 6 K tolerance) 104 °F / 40 °C (± 12.6 °F / 7 K tolerance)
01163.0-01 77 °F / 25 °C (± 9 °F / 5 K tolerance) 59 °F / 15 °C (± 9 °F / 5 K tolerance) 140 °F / 60 °C (± 11 °F / 6 K tolerance) 122 °F / 50 °C (± 12.6 °F / 7 K tolerance)
01163.0-02 59 °F / 15 °C (± 9 °F / 5 K tolerance) 41 °F / 5 °C (± 9 °F / 5 K tolerance) 95 °F / 35 °C (± 11 °F / 6 K tolerance) 77 °F / 25 °C (± 12.6 °F / 7 K tolerance)
01163.0-03 77 °F / 25 °C (± 9 °F / 5 K tolerance) 59 °F / 15 °C (± 9 °F / 5 K tolerance) 122 °F / 50 °C (± 11 °F / 6 K tolerance) 104 °F / 40 °C (± 12.6 °F / 7 K tolerance)
Part No. NO - close on rise NO - close on rise
Switch-on temperature Switch-off temperature Switch-on temperature Switch-off temperature
01164.0-00 122 °F / 50 °C (± 11 °F / 6 K tolerance) 104 °F / 40 °C (± 12.6 °F / 7 K tolerance) 140 °F / 60 °C (± 11 °F / 6 K tolerance) 122 °F / 50 °C (± 12.6 °F / 7 K tolerance)
Two thermostats in one housing:
Tamperproof (Pre-set) Thermostat - NC
Opens on temperature rise (red module housing) - for regulating heaters or for switching signal
devices when temperature has fallen below the minimum value.
Tamperproof (Pre-set) Thermostat - NO
Closes on temperature rise (blue module housing) - for regulating filter fans, heat exchangers, cool-
ing devices or for switching signal devices when temperature limit has been exceeded.
Heaters and cooling equipment can be switched independently from each other with a temperature
offset as opposed to the usual SPDT/change-over contact.
Wiring examples
FTD 011 ThermostatHeater e.g. Fan
Technical Data
Regulating
ZR011//11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
NC / NO or NO / NO in one unit
Separate adjustable temperatures
Color coded temperature dials
DIN rail mountable
The ZR 011 houses two separate thermostats, allowing the independent control of heating and
cooling or other equipment.
Thermostat NC (normally closed):
Thermostat opens at temperature rise - for regulating heaters or for switching signal devices.
Comes with red temperature dial.
Thermostat NO (normally open):
Thermostat closes at temperature rise - for regulating filter fans and heat exchangers or for
switching signal devices. Comes with blue temperature dial.
Switching difference 12.6 °F ± 7 °F tolerance (7 K ± 4 K)
Sensor element thermostatic bimetal
Contact type snap-action contact
Service life > 100,000 cycles
Max. switching capacity NC: 10 A resistive / 2 A inductive at AC 250 V
NO: 5 A resistive / 2 A inductive @ AC 250 V
15 A resistive / 2 A inductive @ AC 120 V
DC 30 W
Max. inrush current AC 16 A for 10 sec.
Connection 4-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +176 °F (-45 to +80 °C)
Dimensions 2.6 x 2.0 x 1.8” (67 x 50 x 46 mm)
Weight approx. 3.2 oz. (90 g)
Protection type IP20
Approvals UL File No. E164102, CSA, VDE
ZR 011 Dual Thermostat
||
Enclosure heater
Filter fan, cooling equipment, signal device
Part No. Setting Range Setting Range
01172.0-00 NC - open on rise 0 to +60 °C NO - close on rise 0 to +60 °C
01172.0-01 NC - open on rise +32 to +140 °F NO - close on rise +32 to +140 °F
01175.0-00 NC - open on rise -10 to +50 °C NO - close on rise +20 to +80 °C
01175.0-01 NC - open on rise 14 to +122 °F NO - close on rise +68 to +176 °F
01176.0-00 NO - close on rise 0 to +60 °C NO - close on rise 0 to +60 °C
01176.0-01 NO - close on rise +32 to +140 °F NO - close on rise +32 to +140 °F
Technical Data
Regulating
||
FZK011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Wide adjustment range
High switching capacity
SPDT (change-over) contact
Very low hysteresis option
DIN rail mountable
The FZK 011 mechanical thermostat is used for controlling heating and cooling equipment, fil-
ter fans or signal devices where a higher degree of sensing accuracy is required. An integrated
resistor (RF) can be connected to improve the switch temperature difference (see Option note).
The thermostat registers the surrounding air and can switch both inductive and resistive loads
via snap-action contact.
Switching difference approx. 9 °F (5 K), tolerance -5.4/+3.6 °F (-3/+2 K)
Option note: connecting terminal “N” (RF heating resistor) enables thermal
feedback, reducing the hysteresis - amount is subject to
surrounding conditions TBD for each individual application
Sensor element thermostatic bimetal
Contact type SPDT / change-over contact
Service life > 100,000 cycles
Max. switching capacity, NC 10 A resistive / 4 A inductive @ AC 120 V
10 A resistive / 4 A inductive @ AC 250 V
DC 30 W
Max. switching capacity, NO 5 A resistive / 2 A inductive @ AC 120 V
5 A resistive / 2 A inductive @ AC 250 V
DC 30 W
Connection 4-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / storage temperature -49 to +149 °F (-45 to +65 °C)
Dimensions 2.64 x 1.97 x 1.5” (67 x 50 x 38 mm)
Weight approx. 3.5 oz. (100g)
Protection type IP20
Part No. Operating voltage1) Setting range Approvals
01170.0-00 AC 230 V 5 to 60 °C UL File No. E164102
01170.0-01 AC 230 V 40 to 140 °F UL File No. E164102
01170.9-00 AC 120 V 40 to 140 °F UL File No. E164102
01170.9-01 AC 120 V 5 to 60 °C UL File No. E164102
1.5” (38 mm)
1.97” (50 mm)
2.64” (67 mm)
FZK 011 Mechanical Thermostat
1) Voltage only needs to be specified if the optional use of the RF resistor is desired.
Enclosure heater
Filter fan, cooling equipment,
signal device
Wiring examples
FZK 011 Thermostat Heater FZK 011 Thermostat e.g. Filter Fan FZK 011 Thermostat e.g. Signal Device
Technical Data
Regulating
||
ETR011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
ETR 011 Electronic Thermostat
Switching difference 7 °F (4 K) ± 1.8 °F (1 K) tolerance - at 68 °F (20 °C)
Sensor element NTC
Reaction time approx. 5 seconds
Contact type SPDT / change-over contact (relay)
Service life > 50,000 cycles
Max. switching capacity (relay output) 8 A resistive / 1.6 A inductive @ AC 120 V
8 A resistive / 1.6 A inductive @ AC 240 V
4 A @ DC 24 V
Max. inrush current AC 16 A for 10 sec.
Connection 5-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -40 to +185 °F (-40 to +85 °C)
Dimensions 2.54 x 1.65 x 1.5” (64.5 x 42 x 38 mm)
Weight approx. 2.5 oz. (70 g)
Protection type IP20
Large setting range
Compact design
Small hysteresis
Optical function display (LED)
DIN rail mountable
The ETR 011 electronic thermostat is used for controlling heating and cooling equip-
ment, filter fans, or signal devices. The thermostat senses the surrounding air temper-
ature and can switch both resistive and inductive loads via an SPDT contact. The inte-
grated LED is lit when the NC contact is closed (i.e. connected heater is operating).
Part No. Operating voltage Setting range Approvals
01131.0-00 AC 230 V, 50/60 Hz -20 to 60 °C CSA-US*, VDE
01131.9-00 AC 120 V, 50/60 Hz -4 to 140 °F CSA-US*
Wiring example
ETR 011 Thermostat Heater
120 V 50/60 Hz
ETR 011 Thermostat ETR 011 Thermostat
e.g. Filter Fan e.g. Signal Device
*Tested according to UL Standard No. 873
Technical Data
Regulating
||
ET011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
ET 011 Electronic Thermostat (DC 24 V)
16 Amp DC switching capacity
Low hysteresis
Wide adjustment range
DIN rail mountable
The ET 011 is an electronic thermostat for regulating high performance DC 24 V equipment.
Heating or cooling equipment, as well as signal devices, can be switched via the SPDT (change-
over) contact.
A relatively small hysteresis sets the ET 011 Thermostat apart from less accurate mechanical
thermostats.
Switching difference approx. 5.4 °F ± 1.8 °F tolerance (3 K ± 1 K)
Sensor element PTC
Contact type SPDT / change-over contact
Service life > 100,000 cycles
Max. switching capacity 16 A @ DC 28 V
Connection 5-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature +32 to +140 °F (0 to +60 °C)
Storage temperature -49 to +176 °F (-45 to +80 °C)
Dimensions 2.6 x 2.0 x 1.8” (67 x 50 x 46 mm)
Weight approx. 2.8 oz. (80 g)
Protection type IP20
Part No. Operating voltage Setting range
01190.0-00 DC 24 V (DC 20-28 V) 0 to 60 °C
01190.0-01 DC 24 V (DC 20-28 V) 32 to 140 °F
1.8” (46 mm)
-+ 241
DC 24V
10
0
20
50
60
30 40
°C
2.6” (67 mm)
2.0” (50 mm)
Wiring examples
ET 011 Thermostat Heater ET 011 Thermostat e.g. Filter Fan ET 011 Thermostat e.g. Signal Device
Technical Data
Regulating
||
EFR012/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
EFR 012 Electronic Hygrostat
Switching difference 5 %RH (± 1 % tolerance) - at 77 °F (25 °C) and 50 %RH
Reaction time approx. 5 seconds
Contact type SPDT / change-over contact (relay)
Service life > 50,000 cycles
Max. switching capacity (relay output) 8 A resistive / 1.6 A inductive @ AC 120 V
8 A resistive / 1.6 A inductive @ AC 240 V
4 A @ DC 24 V
Max. inrush current AC 16 A for 10 sec.
Connection 5-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature +32 to +140 °F (0 to +60 °C)
Storage temperature -4 to +176 °F (-20 to +80 °C)
Max. storage humidity 90 %RH (non-condensing)
Dimensions 2.54 x 1.65 x 1.5” (64.5 x 42 x 38 mm)
Weight approx. 2.3 oz. (65 g)
Protection type IP20
Adjustable & pre-set relative humidity setpoints
Compact design
High switching capacity
Optical function display (LED)
DIN rail mountable
N
4
The EFR 012 electronic hygrostat senses the relative humidity in an enclosure and
turns on a heater at the set point, helping prevent the formation of condensation in the
enclosure. The integrated LED is lit when the connected device is in operation.
Part No. Operating voltage Setting range Approvals
01245.0-00 AC 230 V, 50/60 Hz 40 to 90 %RH CSA-US*, VDE
01245.9-00 AC 120 V, 50/60 Hz 40 to 90 %RH CSA-US*
01246.0-00 AC 230 V, 50/60 Hz 65 %RH pre-set CSA-US*, VDE
01246.9-00 AC 120 V, 50/60 Hz 65 %RH pre-set CSA-US*
Wiring example
EFR 012 Hygrostat Heater
*Tested according to UL Standard No. 873
120 V 50/60 Hz
Technical Data
||
MFR012/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
MFR 012 Mechanical Hygrostat
Regulating
Efficient condensation control
Adjustable relative humidity range
High switching capacity
DIN rail mountable
The MFR 012 electromechanical hygrostat is designed to control the relative humidity inside
enclosures. When connected to an enclosure heater (dehumidifier), it will energize the heater
at the humidity set point in order to raise the dew point. This helps prevent damage and mal-
function of electronic components caused by condensation and corrosion.1)
The MFR 012 can also be used to control cooling fans, warning lights or other devices.
Switching difference 4 %RH (± 3 % tolerance) - at 50 %RH
Permissible air velocity 50 ft/sec (15 m/s)
Contact type SPDT / change-over contact
Service life > 100,000 cycles
Min. Switching capacity 100 mA @ AC/DC 20 V
Max. Switching capacity 5 A resistive @ AC 250 V
DC 20 W
Max. inrush current AC 5 A
Connection 3-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature +32 to +140 °F (0 to +60 °C)
Storage temperature -4 to +176 °F (-20 to +80 °C)
Dimensions 2.64 x 1.97 x 1.5” (67 x 50 x 38 mm)
Weight approx. 2 oz. (60 g)
Protection type IP20
Approvals UL File No. E164102
1) The critical relative humidity level for most components is 65 %. Above 65 %RH, condensation can form and cause
malfunctions of electronic equipment. Long term, this can lead to corrosion and permanent damage of electronic com-
ponents and systems.
Part No. Setting range
01220.0-00 35 to 95 %RH
1.5” (38 mm)
1.97” (50 mm)
2.64” (67 mm)
Enclosure heater
Filter fan, cooling equipment, signal device
Technical Data
N
Regulating
||
ETF012/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Efficient temperature & humidity control
Wide adjustment ranges
High switching capacity
Optical function displays (LED)
DIN rail mountable
The ETF 012 senses the ambient temperature and relative air humidity. Depending on which
contact combination is chosen, it then turns on or off a connected device if either the tempera-
ture is below or the humidity is above the set point. The integrated LED in each adjustment knob
is lit when indicating the active function.
Switching difference - temperature 3.6 °F (2 K) ± 1 K tolerance - at 77 °F (25 °C) and 50 %RH
Switching difference - humidity 4 %RH ± 1 % tolerance - at 77 °F (25 °C) and 50 %RH
Response time - humidity approx. 5 sec.
Contact type SPDT / change-over contact (relay)
Service life NC: > 50,000 cycles
NO: > 100,000 cycles
Max. switching capacity NC: 6 A resistive / 1 A inductive @ AC 120 V
NO: 8 A resistive / 1.6 A inductive @ AC 120 V
NC: 6 A resistive / 1 A inductive @ AC 240 V
NO: 8 A resistive / 1.6 A inductive @ AC 240 V
4 A @ DC 24 V
Max. inrush current AC 16 A for 10 sec.
Connection 5-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating temperature +32 to +140 °F (0 to +60 °C)
Storage temperature -4 to +176 °F (-20 to +80 °C)
Dimensions 3.0 x 2.4 x 1.7” (77 x 60 x 43 mm)
Weight approx. 7 oz. (200 g)
Protection type IP20
Part No. Operating voltage Setting range - temperature Setting range - humidity Approvals
01230.0-00 AC 230 V, 50/60 Hz 0 to 60 °C 50 to 90 %RH UL File No. E164102, VDE
01230.0-01 AC 230 V, 50/60 Hz 32 to 140 °F 50 to 90 %RH UL File No. E164102, VDE
01230.9-00 AC 120 V, 50/60 Hz 32 to 140 °F 50 to 90 %RH UL File No. E164102
01230.9-01 AC 120 V, 50/60 Hz 0 to 60 °C 50 to 90 %RH UL File No. E164102
ETF 012 Electronic Hygrotherm
Wiring example
ETF 012 Hygrotherm Heater
Technical Data
Regulating
SM 010 Electronic Relay (DC 24 V & DC 48 V)
||
SM010/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
16 Amp DC switching capacity
Variety of applications
Compact design
DIN rail mountable
The SM 010 Electronic Relay is used for switching high powered DC operated equipment, such
as heaters, up to 16 amps. A separate conventional switch contact is used as controller (e.g.
thermostat, hygrostat). The electronic relay is available in DC 24 V and DC 48 V versions.
Contact type NO - normally open (Relay/MOSFET)
Service life > 100,000 cycles
Max. inrush current DC 16 A
Connection 6-pole terminal, clamping torque 0.5 Nm max.:
solid wire - AWG 14 max. (2.5 mm²)
stranded wire (w/ wire end ferrule) - AWG 16 max. (1.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 2.6 x 2.0 x 1.8” (67 x 50 x 46 mm)
Weight approx. 3.0 oz. (85 g)
Protection type IP20
Approvals VDE, UL File No. E342261
Part No. Operating voltage Max. Switching capacity Signal current
01000.0-01 DC 48 V (DC 38-56 V) 16 A @ DC 56 V 10 mA @ DC 38 V / 18 mA @ DC 56 V
01001.0-01 DC 24 V (DC 20-28 V) 16 A @ DC 28 V 13 mA @ DC 20 V / 22 mA @ DC 28 V
Load, e.g. heater,
cooling device with
temperature limiter
SM 010
Electronic
relay
Control contact,
e.g. thermostat,
hygrostat, or pressure
regulator
SM 010
Electronic
relay
Control contact,
e.g. thermostat,
hygrostat, or pressure
regulator
Load, e.g. heater,
cooling device without
temperature limiter
Wiring examples
Technical Data
||
REx011/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
REx 011 Explosion-proof Thermostat
Compact design
Fixed temperature setpoints
High switching capacity
DIN rail mountable
The design of the REx 011 thermostat ensures high accuracy, small switching difference (hys-
teresis) and a long service life.
Because of the high switching capacity of the thermostat, heaters can usually be directly con-
nected and switched without the need for additional relays.
Explosion proof according to EN LCIE (Laboratoire Central des Industries Electriques)
Conformity certificate 01 ATEX 6074/02, LCIE N°06 ATEX Q8011, IECEx LCI 07. 0021
Sensor element thermostatic bimetal
Contact type NC - normally closed (opens on temperature rise)
Service life > 100,000 cycles
Max. switching capacity 4 A resistive / 1 A inductive @ AC 250 V
Connection Si HF - JZ 3 x AWG 18 (0.75 mm²), length 3.3 ft (1 m)
Housing aluminum, black anodized
Mounting mounting bracket with M8 nut and clip for 35 mm DIN rail
Mounting position variable
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Weight approx. 7 oz. (200 g)
Protection class I(grounded)
Protection type IP65
Part No. Ex protection type Switch-off temperature Switching difference
01180.0-00 Ex d IIC T6 - Ex tD A21 IP6X T85°C 59 °F ± 7 °F tolerance (15 °C ± 4 K tolerance) 7 °F ± 2 °F tolerance (4 K ± 1 K tolerance)
01181.0-00 Ex d IIC T6 - Ex tD A21 IP6X T85°C 77 °F ± 7 °F tolerance (25 °C ± 4 K tolerance) 7 °F ± 2 °F tolerance (4 K ± 1 K tolerance)
4.33” (110 mm)
0.87” (22 mm)
M8
0.33” (8.5 mm)
1.97”
0.94”
0.79”
0.79”
1.38”
0.08”
Ø0.35”
Ø0.165” Ø0.14”
Aluminum
Mounting Bracket
1.02”
Regulating
Ø 0.9” (2.4mm)
Technical Data
||
RCE016/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Compact size
Wide voltage range
Heating power adjusts to ambient temperature
Energy saving
The RCE 016 small heaters have been designed to prevent condensation and to ensure a mini-
mum operating temperature in small enclosures.
Heating
Operating voltage see table below
Heating element PTC resistor - temperature limiting
Heater body aluminum, anodized
Insulation PTFE / Kapton
Mounting 2 pressure clips included (mounting screws not included)
Mounting position variable
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP54
L
N
19.7” (500 mm)
1.97” (50 mm)
1.77” (45 mm)
2 x AWG 22 (0.25 mm²)
Ø 0.39”
(10 mm)
Part No. Heating capacity1) Operating voltage2) Max. current (inrush) Surface temperature (approx.)1) Weight (approx.) Approvals
01622.0-03 5 W AC/DC 120-240 V 2.0 A 329 °F (165 °C) 0.7 oz. (20 g) UL File No. E234324, VDE
01623.0-01 9 W AC/DC 120-240 V 2.5 A 347 °F (175 °C) 0.7 oz. (20 g) UL File No. E234324, VDE
01624.0-03 5 W AC/DC 12-30 V 5.8 A 284 °F (140 °C) 0.7 oz. (20 g) UL File No. E234324
01625.0-02 9 W AC/DC 12-30 V 2.4 A 360 °F (182 °C) 0.7 oz. (20 g) UL File No. E234324
RCE 016 PTC Heater 5 & 9 W
Mounting clip
Measured in open air
(W)
2
3
4
5
6
7
8
9
10
-20-30-40 -
10 0 102030405060 (°C)
01622.0-03
01623.0-01
Power / Ambient Temperature Diagram
AC/DC 120 - 240 V
Wiring example
Thermostat RCE 016 Heater
1) at 68 °F (20 °C) ambient temperature
2) operating high voltage heaters below AC/DC 140 V reduces heating performance by approx. 10% (min. 110 V, max 265 V).
∅∅0.09” (2.4 mm)
Technical Data
Heating
||
RC016/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
RC 016 PTC Heater 8 - 13 W
Compact size
Wide voltage range
Heating power adjusts to ambient temperature
Energy saving
The RC 016 small heaters are designed to prevent condensation and to ensure a minimum oper-
ating temperature in small enclosures.
Operating voltage see table below
Heating element PTC resistor - temperature limiting
Heater body aluminum, anodized
Insulation PTFE / Kapton
Mounting screw (mounting screws not included)
Mounting position variable
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP54
Part No. Heating capacity1) Operating voltage2) Max. current (inrush) Surface temperature (approx.)1) Weight (approx.) Approvals
01602.0-00 8 W AC/DC 120-240 V 2.0 A 302 °F (150 °C) 0.7 oz. (20 g) UL File No. E234324, VDE
01602.0-03 8 W AC/DC 12-30 V 3.7 A 273 °F (134 °C) 0.7 oz. (20 g) UL File No. E234324
01609.0-00 10 W AC/DC 120-240 V 2.5 A 311 °F (155 °C) 1.0 oz. (28 g) UL File No. E234324, VDE
01609.0-01 10 W AC/DC 12-30 V 5.7 A 270 °F (132 °C) 1.0 oz. (28 g) UL File No. E234324
01610.0-00 13 W AC/DC 120-240 V 3.0 A 338 °F (170 °C) 1.2 oz. (34 g) UL File No. E234324, VDE
01610.0-01 13 W AC/DC 12-30 V 10.0 A 298 °F (148 °C) 1.2 oz. (34 g) UL File No. E234324
L
N
Part. No. 01610.0-00
1.57” (40 mm)
2.36”(60 mm)
0.49” (12.5 mm)
0.07”
(1.8
mm)
0.49” (12.5 mm)
0.18”
(4.5mm)
0.18”
(4.5mm)
0.2”
(5mm)
13” (340 mm)
2 x AWG 22 (0.25 mm²)
Part. No. 01609.0-00
1.2" (30 mm)
1.97" (50 mm) 13” (340 mm)
2 x AWG 22 (0.25 mm²)
0.18”
(4.5
mm)
0.2”
(5mm)
0.18”
(4.5
mm)
0.07”
(1.8
mm)
0.49” (12.5 mm)
0.49” (12.5 mm)
Part. No. 01602.0-00
0.12”
(3.2
mm)
0.7" (18 mm)
1.2" (30 mm) 11.8" (300 mm)
2 x AWG 18 (0.75 mm²)
0.12" (3.2 mm)
0.18"
(4.5 mm)
0.07”
(1.8
mm)
0.49” (12.5 mm)
0.49” (12.5 mm)
: measured in open air
: measured with heater mounted on 100 x 100 x 2 mm
(4 x 4 x 0.08")aluminum plate
Heating Power in Relation to Ambient Temperature
AC/DC 120 - 240 V
(W)
(°F)
(°C)
-20
-4 14 32 50 68 86 104 122 140
-
10 0 102030405060
14
6
8
10
12
16
18
20
22
24
26
28
30
01610.0-00
01610.0-00
01609.0-00
01609.0-00
01602.0-00
01602.0-00
Wiring example
1) at 68°F (20°C) ambient temperature
2) operating high voltage heaters below AC/DC 140V reduces heating performance by approx. 10% (min. 110V, max 265V).
Thermostat RC 016 Heater
2 x AWG 24 (0.2 mm2)
24 (0.2
2 x AWG 24 (0.2 mm2)
Technical Data
Heating
||
CSK060/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CSK 060 Touch-Safe PTC Heater 10 & 20 W
Low surface temperature
Compact size
Wide voltage range
Double insulated protection
DIN rail mountable
Heating capacity see table
Heating element PTC resistor - temperature limiting
Surface temperature < 185 °F (85 °C), except upper protective grill
Connection 2-pole terminal AWG 14 max (2.5 mm²), torque 0.8 Nm max.
Mounting clip for 35 mm DIN rail, EN 60715
Housing plastic, UL 94V-0, black
Mounting position vertical
Operating / storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP20
Approvals UL File No. E234324, VDE
Note other voltages available upon request
The CSK 060 is a touch-safe heater for use in enclosures. The design of the heater utilizes nat-
ural convection which results in a circulating current of warm air. The surface temperatures on
the accessible side surfaces of the housing are minimized as a result of the heater design.
Part No. Heating capacity1) Operating voltage2) Max. current (inrush) Dimensions Weight (approx.)
06030.0-00 20 W AC/DC 120-240 V 2.5 A 3.86 x 2.95 x 1.5” (98 x 75 x 38 mm) 6.1 oz. (170 g)
06040.0-00 10 W AC/DC 120-240 V 1.0 A 3.86 x 2.95 x 1.5” (98 x 75 x 38 mm) 5.0 oz. (140 g)
06040.1-00 10 W AC/DC 12-30 V 8 A 3.86 x 2.95 x 1.5” (98 x 75 x 38 mm) 5.0 oz. (140 g)
Wiring example
Thermostat CSK 060 Heater
1) at 68 °F (20 °C) ambient temperature
2) operating high voltage heaters below AC/DC 140 V reduces heating performance by approx. 10% (min. 110 V, max 265 V).
Technical Data
Heating
||
HGK047/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
HGK 047 PTC Heater 10 - 30 W
Compact size
Wide voltage range
Heating power adjusts to ambient temperature
DIN rail mountable
The HGK 047 heaters are used in enclosures to maintain minimum operating temperatures and
to help prevent failure of electronic components caused by condensation and corrosion.
Part No. Heating capacity1) Operating voltage2) Max. current
(inrush) Length (L) Weight (approx.) Approvals
04700.0-00 10 W AC/DC 140-240 V 1.0 A 2.05” (52 mm) 3.0 oz. (85 g) VDE
04701.0-00 20 W AC/DC 140-240 V 2.5 A 2.36” (60 mm) 3.6 oz. (100 g) VDE
04702.0-00 30 W AC/DC 140-240 V 3.0 A 2.76” (70 mm) 4.0 oz. (110 g) VDE
04700.9-00 10 W AC/DC 110-120 V 1.0 A 2.05” (52 mm) 3.0 oz. (85 g) UL File No. E234324
04701.9-00 20 W AC/DC 110-120 V 1.5 A 2.76” (70 mm) 4.0 oz. (110 g) UL File No. E234324
04702.9-00 30 W AC/DC 110-120 V 1.5 A 3.94” (100 mm) 5.2 oz. (150 g) UL File No. E234324
1) at 68 °F (20 °C) ambient temperature
2) operating with voltages below AC/DC 140 V reduces heating performance by approx. 10% (min. 110 V, max 265 V).
L
N
1.97” (50 mm)
0.98” (25 mm)
L
0.47”
(12 mm)
11.8” (300 mm)
Operating voltage see table below
Heating element PTC resistor - temperature limiting
Heater body extruded aluminum profile, anodized
Connection 3 x AWG 20 (0.5 mm²), 12” (300 mm) length
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class I(grounded)
Protection type IP44
Wiring example
Thermostat HGK 047 Heater
Technical Data
Heating
||
CS060/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CS 060 Touch-Safe PTC Heater 50 - 150 W
Low surface temperature
Compact size
Wide voltage range
Double insulated protection
DIN rail mountable
The CS 060 is a touch-safe heater for use in enclosures. The design of the heater utilizes nat-
ural convection which results in a circulating current of warm air. The surface temperatures on
the accessible side surfaces of the housing are minimized as a result of the heater design. The
CS 060 is also available in a version with a plug-in thermostat requiring no additional wiring
(CSF 060).
Operating voltage* AC/DC 120-240 V (min. 110 V, max. 265 V)
Heating capacity see table
Heating element PTC resistor - temperature limiting
Surface temperature < 176 °F (80 °C), except upper protective grill
Connection 4-pole terminal AWG 14 max (2.5 mm²), torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP20
Approvals UL File No. E234324, VDE
Note other voltages available upon request
*Operating with voltages below AC/DC 140 V reduces heating performance by approx. 10%.
Part No. Heating capacity1) Max. current (inrush) Air outlet temperature2) Dimensions Weight (approx.)
06000.0-00 50 W 2.5 A 187 °F (86 °C) 4.3 x 2.36 x 3.54” (110 x 60 x 90 mm) 10.4 oz. (295 g)
06010.0-00 100 W 4.5 A 248 °F (120 °C) 4.3 x 2.36 x 3.54” (110 x 60 x 90 mm) 10.6 oz. (300 g)
06020.0-00 150 W 8 A 293 °F (145 °C) 5.9 x 2.36 x 3.54” (150 x 60 x 90 mm) 15.5 oz. (440 g)
Wiring examples
50
0
200
150
100
Heating Power (W)
-40°C
-40°F -20°C
-4°F 0°C
32°F
Ambient Temperature
20°C
68°F 40°C
104°F
150 W
100 W
50 W
178
160
147
132 119
122
110 102 93 85
66 61 55 50 44
1) see Heating capacity / Ambient temperature diagram
2) measured 2” (50 mm) above protective grill
Thermostat CS 060 Heater
CS 060 Heater
Technical Data
Heating
||
CSF060/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CSF 060 Touch-Safe PTC Heater 50 - 150 W
Low surface temperature
Integrated thermostat
Compact size
Wide voltage range
Double insulated protection
DIN rail mountable
The CSF 060 is a touch-safe heater for use in enclosures. The design of the heater utilizes nat-
ural convection which results in a circulating current of warm air. The surface temperatures on
the accessible side surfaces of the housing are minimized as a result of the heater design. This
model with plug-in thermostat does not require additional wiring. The CSF 060 is also available
in a version without thermostat (CS 060).
Operating voltage* AC/DC 120-240 V (min. 110 V, max. 265 V)
Heating capacity see table
Heating element PTC resistor - temperature limiting
Surface temperature < 176 °F (80 °C), except upper protective grill
Connection 4-pole terminal AWG 14 max (2.5 mm²), torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -40 to +158 °F (-40 to +70 °C) / -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP20
Approvals VDE
*Operating with voltages below AC/DC 140 V reduces heating performance by approx. 10%.
Part No. Heating
capacity1)
Max. current
(inrush)
Air outlet
temperature2)
Switch-off
temperature3)
Switch-on
temperature3) Dimensions Weight
(approx.)
06001.0-00 50 W 2.5 A 187 °F (86 °C) 59 °F (15 °C) 41 °F (5 °C) 5.24 x 2.36 x 3.54” (133 x 60 x 90 mm) 10.8 oz. (305 g)
06002.0-00 50 W 2.5 A 187 °F (86 °C) 77 °F (25 °C) 59 °F (15 °C) 5.24 x 2.36 x 3.54” (133 x 60 x 90 mm) 10.8 oz. (305 g)
06011.0-00 100 W 4.5 A 248 °F (120 °C) 59 °F (15 °C) 41 °F (5 °C) 5.24 x 2.36 x 3.54” (133 x 60 x 90 mm) 11.2 oz. (320 g)
06012.0-00 100 W 4.5 A 248 °F (120 °C) 77 °F (25 °C) 59 °F (15 °C) 5.24 x 2.36 x 3.54” (133 x 60 x 90 mm) 11.2 oz. (320 g)
06021.0-00 150 W 8.0 A 293 °F (145 °C) 59 °F (15 °C) 41 °F (5 °C) 6.8 x 2.36 x 3.54” (173 x 60 x 90 mm) 15.9 oz. (450 g)
06022.0-00 150 W 8.0 A 293 °F (145 °C) 77 °F (25 °C) 59 °F (15 °C) 6.8 x 2.36 x 3.54” (173 x 60 x 90 mm) 15.9 oz. (450 g)
1) see Heating capacity / Ambient temperature diagram
2) measured 2” (50 mm) above protective grill
3) tolerance of ± 5K
50
0
200
150
100
Heating Power (W)
-40°C
-40°F -20°C
-4°F 0°C
32°F
Ambient Temperature
20°C
68°F 40°C
104°F
150 W
100 W
50 W
178
160
147
132 119
122
110 102 93 85
66 61 55 50 44
Wiring example
CSF 060 Heater
Technical Data
Heating
||
HG140/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
HG 140 PTC Heater 15 - 150 W
Compact size
Wide voltage range
Heating power adjusts to ambient temperature
Cage clamp connectors for quick & easy wiring
DIN rail mountable
These heaters are used in enclosures where damage from condensation must be prevented, or
where the temperature must be maintained above a minimum value. The aluminum profile
heater body design has a chimney effect to distribute heat evenly. The cage clamp connectors
save time and simplify installation.
Operating voltage* AC/DC 120-240 V (min. 110 V, max. 265 V)
Heating element PTC resistor - temperature limiting
Heater body extruded aluminum profile, anodized
Connection 3 cage clamps for solid wire AWG 20-14 (0.5-2.5 mm²), and
stranded wire AWG 20-16 (0.5-1.5 mm²) with wire end ferrule
Connection casing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class I(grounded)
Protection type IP20
Approvals UL File No. E234324, VDE
Note other voltages available upon request
*Operating with voltages below AC/DC 140 V reduces heating performance by approx. 10%.
Part No. Heating capacity1) Max. current (inrush) Length (L on dim. dwg.) Weight (approx.)
14000.0-00 15 W 1.5 A 2.56” (65 mm) 7.6 oz. (215 g)
14001.0-00 30 W 3.0 A 2.56” (65 mm) 7.6 oz. (215 g)
14003.0-00 45 W 3.5 A 2.56” (65 mm) 7.6 oz. (215 g)
14005.0-00 60 W 2.5 A 5.5” (140 mm) 14.1 oz. (400 g)
14006.0-00 75 W 4.0 A 5.5” (140 mm) 14.3 oz. (405 g)
14007.0-00 100 W 4.5 A 5.5” (140 mm) 14.3 oz. (405 g)
14008.0-00 150 W 9.0 A 8.66” (220 mm) 21.3 oz. (600 g)
1) at 68 °F (20 °C) ambient temperature
Technical Data
Heating
||
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CS 028 Touch-Safe PTC Fan Heater 150 W
The CS 028 fan heater prevents formation of condensation and provides an evenly distributed
interior air temperature in enclosures. The heater is connected using the internal terminal con-
nectors. The surface temperatures on the accessible side surfaces of the housing are minimized
as a result of the heater design. The CS 028’s small size make it ideal for use in enclosures
where space is at a premium.
Heating element PTC resistor - temperature limiting
Max. current (inrush) 6 A @ AC 120 V, 12 A @ AC 230 V
Surface temperature max. 122 °F (50 °C) at housing, 212 °F (100 °C) at top grill;
measured at 68 °F (20 °C) ambient temperature
Axial fan, ball bearing service life 40,000 h at 104 °F (40 °C)
Air flow, free blowing approx. 8 cfm (13.8 m³/h)
Connection 2-pole terminal AWG 14 max. (2.5 mm²), torque 0.8 Nm max.
Mounting screw mount or clip for 35 mm DIN rail, EN 60715
Housing plastic, UL 94V-0, black
Weight approx. 10.6 oz. (300 g)
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP20
Note other voltages available upon request
Part No. Heating capacity1) Operating voltage Dimensions Mounting Approvals
02800.0-00 150 W AC 230 V, 50/60 Hz 2.95 x 2.56 x 3.54” (75 x 65 x 90 mm) DIN clip UL File No. E234324, VDE
02800.0-01 150 W AC 230 V, 50/60 Hz 4.49 x 2.56 x 3.54” (114 x 65 x 90 mm) Screw mount UL File No. E234324, VDE
02800.9-00 150 W AC 120 V, 50/60 Hz 2.95 x 2.56 x 3.54” (75 x 65 x 90 mm) DIN clip UL File No. E234324
02800.9-01 150 W AC 120 V, 50/60 Hz 4.49 x 2.56 x 3.54” (114 x 65 x 90 mm) Screw mount UL File No. E234324
1) at 68 °F (20 °C) ambient temperature
Ambient Temperature
Heating Power (W)
3.54” (90 mm)
2.95” (75 mm) 2.56” (65 mm)
1.26” (32 mm)
3.74” (95 mm)
2.95” (75 mm)
View: back side
Screw mount DIN clip
30
20
10
0
40
50
60
L
N
4
3
Wiring example
Compact size
Quiet operation
Heating power adjusts to ambient temperature
DIN rail or screw mount available
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
CS028/11-12/US
CS 028 Fan Heater
Thermostat
3.54” (90 mm)
4.37” (111 mm)
Technical Data
Heating
||
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CSL 028 Touch-Safe PTC Fan Heater 250 & 400 W
The CSL 028 fan heater prevents formation of condensation and provides an evenly distributed
interior air temperature in enclosures. The heater is connected using the internal terminal con-
nectors. The surface temperatures on the accessible side surfaces of the housing are minimized
as a result of the heater design. The CSL 028’s small size make it ideal for use in enclosures
where space is at a premium.
Heating element PTC resistor - temperature limiting
Surface temperature 250 W: max. 122 °F (50 °C) except upper protective grill,
400 W: max. 149 °F (65 °C) except upper protective grill;
measured at 68 °F (20 °C) ambient temperature
Axial fan, ball bearing service life 40,000 h at 104 °F (40 °C)
Air flow, free blowing 32 cfm (54 m³/h) at AC 120 V; 26 cfm (45 m³/h) at AC 230 V
Connection 2-pole terminal AWG 14 max. (2.5 mm²) with strain relief,
screw torque 0.8 Nm max.
Mounting screw mount or clip for 35 mm DIN rail, EN 60715
Housing plastic, UL 94V-0, black
Weight approx. 17.6 oz. (500 g)
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class II (double insulated)
Protection type IP20
Part No. Heating capacity1) Operating voltage Max. current (inrush) Dimensions Mounting Approvals
02810.0-00 400 W AC 230 V, 50/60 Hz 15 A 3.54 x 3.35 x 4.37” (90 x 65 x 111 mm) DIN clip UL File No. E234324, VDE
02810.0-01 400 W AC 230 V, 50/60 Hz 15 A 5.08 x 3.35 x 4.37” (129 x 65 x 111 mm) Screw mount UL File No. E234324, VDE
02810.9-00 400 W AC 120 V, 50/60 Hz 9 A 3.54 x 3.35 x 4.37” (90 x 65 x 111 mm) DIN clip UL File No. E234324
02810.9-01 400 W AC 120 V, 50/60 Hz 9 A 5.08 x 3.35 x 4.37” (129 x 65 x 111 mm) Screw mount UL File No. E234324
02811.0-00 250 W AC 230 V, 50/60 Hz 9 A 3.54 x 3.35 x 4.37” (90 x 65 x 111 mm) DIN clip UL File No. E234324, VDE
02811.0-01 250 W AC 230 V, 50/60 Hz 9 A 5.08 x 3.35 x 4.37” (129 x 65 x 111 mm) Screw mount UL File No. E234324, VDE
02811.9-00 250 W AC 120 V, 50/60 Hz 6 A 3.54 x 3.35 x 4.37” (90 x 65 x 111 mm) DIN clip UL File No. E234324
02811.9-01 250 W AC 120 V, 50/60 Hz 6 A 5.08 x 3.35 x 4.37” (129 x 65 x 111 mm) Screw mount UL File No. E234324
1) at 68°F (20°C) ambient temperature
Ambient Temperature
Heating Power (W)
View: back side
Screw mount DIN clip
Wiring
example
Compact size
Quiet operation
Heating power adjusts to ambient temperature
DIN rail or screw mount available
-40°C -20°C 0°C 20°C 40°C 60°C
-40°F -4°F 32°F 68°F 104°F 140°F
CSL028/11-12/US
CSL 028 Fan Heater
Thermostat
1.26” (32 mm)
4.33” (110 mm) 3.35” (85 mm)
Technical Data
Heating
||
HVL031/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
The compact HVL 031 high-performance fan heater prevents formation of condensation and pro-
vides an evenly distributed interior air temperature in enclosures. For large OEM use, this fan
heater can also be provided without the fan, in which case the OEM/customer must provide a
fan which meets the minimum airflow requirements.
Compact size
Flat design
Built-in overheat protection
3-side DIN rail mountable
HVL 031 Fan Heater 100 - 400 W
Heating element high performance cartridge
Overheat protection built-in temperature limiter
Heater body die-cast aluminum, glass bead finish
Connection 3-pole terminal AWG 14 max. (2.5 mm²), torque 0.8 Nm max..
Connection housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position horizontal
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class / Protection type I(grounded) / IP20
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing see table below
Axial fan connection 2-pole terminal AWG 14 max. (2.5 mm²), terminals L2/N2
Approvals UL File No. E187294 (all), VDE (230VAC only)
Part No. - AC 120 V Part No. - AC 230 V Heating capacity Min. airflow
(free blowing) Dimensions (as mounted) Weight (approx.)
03102.9-00 03102.0-00 100 W 20 cfm (35 m³/h) 1.85 x 3.15 x 4.41” (47 x 80 x 112 mm) 1.3 lbs. (600 g)
03103.9-00 03103.0-00 150 W 20 cfm (35 m³/h) 1.85 x 3.15 x 4.41” (47 x 80 x 112 mm) 1.3 lbs. (600 g)
03113.9-00 03113.0-00 200 W 63 cfm (108 m³/h) 1.85 x 4.68 x 5.94” (47 x 119 x 151 mm) 2.0 lbs. (900 g)
03114.9-00 03114.0-00 300 W 63 cfm (108 m³/h) 1.85 x 4.68 x 5.94” (47 x 119 x 151 mm) 2.0 lbs. (900 g)
03115.9-00 03115.0-00 400 W 63 cfm (108 m³/h) 1.85 x 4.68 x 5.94” (47 x 119 x 151 mm) 2.0 lbs. (900 g)
Important! Heater must be operated together with a fan.
Operating without a fan creates the danger of overheating.
Mounting hole for DIN clip
Air flow
Axial fan
Label
100W/ 150W Heater
200W/ 300W/ 400W Heater
0.16” (4.2 mm)
4.68” (119 mm)
3.15” (80 mm)
1.26” (32 mm)
2.68” (68 mm)
0.71” (18 mm)
0.98” (25 mm)
0.87” (22 mm)
0.16” (4.2 mm)
0.16” (4.2 mm)
2.81” (71.5 mm)
4.13” (104.8 mm)
1.26” (32 mm)
2.68” (68 mm)
0.71” (18 mm)
0.98” (25 mm)
0.87” (22 mm)
Mounting hole for DIN clip
Axial fan
Label
Air flow
Shown: 100W - HVL 031 Fan Heater
L
N
12
HVL 031 Fan Heater
Thermostat
Technical Data
Heating
||
HGL046/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
HGL 046 Fan Heater 250 & 400 W
Compact size
Built-in overheat protection
Long service life
DIN rail mountable
The compact HGL 046 fan heater prevents formation of condensation. The integrated high per-
formance axial fan provides forced air circulation and so guarantees an even temperature in
enclosures. The heater is wired using the internal terminal connectors.
Heating element resistance - micanite
Overheat protection built-in temperature limiter
Heater body extruded aluminum, anodized
Surface temperature 400 W heater - max. 167 °F (75 °C)
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing AC: 26 cfm (45 m³/h) - 50 Hz; 32 cfm (54 m³/h) - 60 Hz
DC: 32 cfm (54 m³/h)
Connection 3-pole terminal AWG 16 max. (1.5 mm²) with strain relief,
clamping torque 0.8 Nm max.
Connection housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class I(grounded)
Protection type IP20
Note: In the case of DC 24 V and DC 48 V, the fan heater must be switched via a relay. For this application,
the SM 010 Electronic Relay (Part No. 01000.0-00 or 01001.0-00) is recommended.
3.35” (85 mm)
L
3.35” (85 mm)
3.94” (100 mm)
Part No. Heating capacity Operating voltage Length (L) Weight (approx.) Approvals
04640.0-00 250 W AC 230 V, 50/60 Hz 7.2” (182 mm) 2.4 lbs. (1.1 kg) UL File No. E234324, VDE
04641.0-00 400 W AC 230 V, 50/60 Hz 8.7” (222 mm) 3.1 lbs. (1.4 kg) UL File No. E234324, VDE
04640.9-00 250 W AC 120 V, 50/60 Hz 7.2” (182 mm) 2.4 lbs. (1.1 kg) UL File No. E234324, VDE
04641.9-00 400 W AC 120 V, 50/60 Hz 8.7” (222 mm) 3.1 lbs. (1.4 kg) UL File No. E234324, VDE
04640.1-00 250 W DC 24 V 7.2” (182 mm) 2.4 lbs. (1.1 kg) UL File No. E234324
04640.2-00 250 W DC 48 V 7.2” (182 mm) 2.4 lbs. (1.1 kg) UL File No. E234324
04641.2-00 400 W DC 48 V 8.7” (222 mm) 3.1 lbs. (1.4 kg) UL File No. E234324
Pilot contact
e.g. KT 011 Thermostat
Pilot contact
e.g. KT 011 Thermostat
Heater
Fan Heater HGL 046
(AC 120 V or AC 230 V)
Heater
Fan Heater HGL 046
(DC 24 V or DC 48 V)
SM 010
Electronic
relay
Technical Data
Heating
||
CR027/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CR 027 PTC Fan Heater 400 - 650 W
Compact fan heater
Heating power adjusts to ambient temperature
Integrated adjustable thermostat
Built-in overheat protection
DIN rail mountable
The semiconductor CR 027 fan heater prevents the formation of condensation and ensures an
even temperature in enclosures. The integrated thermostat is used to set the desired tempera-
ture while the high performance axial fan provides forced air circulation. The CR 027 is also
available with a continuously running fan (when powered).
Heating element PTC resistor - temperature limiting
Overheat protection built-in temperature limiter
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing see table below
Connection 2-pole terminal AWG 14 max. (2.5 mm²), torque 0.8 Nm max..
Housing plastic, UL 94V-0, light grey
Optical indicator thermostat control light
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 6.5 x 3.94 x 5.0” (165 x 100 x 128 mm)
Protection class II (double insulated)
Protection type IP20
Approvals UL File No. E204590
Part No. Heating capacity1)
(@ 50 Hz)
Heating capacity1)
(@ 60 Hz) Operating voltage Max. current
(inrush)
Air flow,
free blowing
Thermostat
setting range
Weight
(approx.)
02700.0-00 475 W 550 W AC 220-240 V 11.0 A 20 cfm (35 m³/h) 0 to 60 °C 2.0 lbs. (0.9 kg )
02701.0-00 550 W 650 W AC 220-240 V 13.0 A 26 cfm (45 m³/h) 0 to 60 °C 2.4 lbs (1.1 kg)
02700.9-00 400 W 550 W AC 100-120 V 14.0 A 20 cfm (35 m³/h) 32 to 140 °F 2.0 lbs. (0.9 kg )
02701.9-00 510 W 650 W AC 100-120 V 15.0 A 26 cfm (45 m³/h) 32 to 140 °F 2.4 lbs (1.1 kg)
1) at 68 °F (20 °C) ambient temperature
4.8” (124 mm)
5” (128 mm)
3.94” (100 mm)
6.5” (165 mm)
700
750
800
650
600
550
500
450
400
900
850
650W
550W
-40°C
-40°F
-20°C
-4°F
0°C
32°F
20°C
68°F
40°C
104°F
Heating Power / Ambient Temperature (@ 50 Hz) Heating Power / Ambient Temperature (@ 60 Hz)
Temperature Temperature
Heating Power (W)
Heating Power (W)
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
Wiring note: Only connect the L and N1 terminals - N2 is not
used and Grounding is not required
Technical Data
Heating
||
CR030/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CR 030 Foot-mount Fan Heater 950 W
Compact design
Built-in overheat protection
Integrated adjustable thermostat or fixed hygrostat
Double insulated plastic housing
Heating element high performance cartridge
Overheat protection built-in temperature limiter
Heater body extruded aluminum
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing 94 cfm (160 m³/h)
Connection 2-pole terminal AWG 14 max. (2.5 mm²) with strain relief,
clamping torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting M5 screws (not included)
Mounting position horizontal
Operating* / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 3.9 x 5.7 x 6.6” (100 x 145 x 168 mm)
Weight approx. 3.1 lbs. (1.4 kg)
Protection class II (double insulated)
Protection type IP20
* Operating temperature of heater with integrated hygrostat: +32 to +140 °F (0 to +60 °C)
The compact CR 030 high performance fan heater prevents formation of condensation and pro-
vides an evenly distributed interior air temperature in enclosures. This fan heater is available
with an integrated thermostat for temperature control or a pre-set hygrostat for humidity con-
trol. The CR 030 was designed as a stationary unit for the bottom of the enclosure. For panel
or DIN rail mount, the CR 130 fan heater is recommended.
30
6.6” (168 mm)
3.9” (100 mm) 5.7” (145 mm)
5.1” (130 mm)
4.1” (105 mm)
Part No. Heating capacity Operating voltage Setting range Approvals
03051.0-00 950 W AC 230 V, 50/60 Hz 0 to 60 °C UL File No. E234324, VDE
03051.0-02 950 W AC 230 V, 50/60 Hz 65 %RH, factory-set UL File No. E234324, VDE
03051.0-07 950 W AC 230 V, 50/60 Hz none (no integrated controls) UL File No. E234324, VDE
03059.9-00 950 W AC 120 V, 50/60 Hz 32 to 140 °F UL File No. E234324
03059.9-02 950 W AC 120 V, 50/60 Hz none (no integrated controls) UL File No. E234324
LL
NN
M
Wiring diagram
Technical Data
Heating
||
CR130/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Compact design
Built-in overheat protection
Integrated adjustable thermostat or fixed hygrostat
Double insulated plastic housing
Panel or DIN rail mounting
The compact CR 130 high performance fan heater prevents formation of condensation and pro-
vides an evenly distributed interior air temperature in enclosures. This fan heater is available
with an integrated thermostat for temperature control or a pre-set hygrostat for humidity con-
trol. The CR 130 was designed as a stationary unit for panel or DIN rail mounting. For foot
mounting on the bottom of an enclosure, the CR 030 fan heater is recommended.
Heating element high performance cartridge
Overheat protection built-in temperature limiter
Heater body extruded aluminum
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing 94 cfm (160 m³/h)
Connection 2-pole terminal AWG 14 max. (2.5 mm²) with strain relief,
clamping torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715 or M6 screws (not included)
Mounting position horizontal
Operating* / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 3.9 x 6.3 x 7.2” (99 x 160 x 182 mm)
Weight approx. 3.1 lbs. (1.4 kg)
Protection class II (double insulated)
Protection type IP20
* Operating temperature of heater with integrated hygrostat: +32 to +140 °F (0 to +60 °C)
CR 130 Panel-mount Fan Heater 950 W
30
7.2” (182 mm)
5.6” (142 mm)
3.9” (99 mm) 6.3” (160 mm)
2.6” (67 mm)
Part No. Heating capacity Operating voltage Setting range Approvals
13051.0-00 950 W AC 230 V, 50/60 Hz 0 to 60 °C UL File No. E234324, VDE
13051.0-02 950 W AC 230 V, 50/60 Hz 65 %RH, factory-set UL File No. E234324, VDE
13051.0-03 950 W AC 230 V, 50/60 Hz none (no integrated controls) UL File No. E234324, VDE
13059.9-00 950 W AC 120 V, 50/60 Hz 32 to 140 °F UL File No. E234324
13059.9-02 950 W AC 120 V, 50/60 Hz none (no integrated controls) UL File No. E234324
LL
NN
M
Wiring diagram
Technical Data
Compact design
High heating performance
Double insulated plastic housing
DIN or screw mount
Optional integrated fixed thermostat
The compact CS 032 high performance fan heater prevents the formation of condensation and
provides an evenly distributed interior air temperature in enclosures. The plastic housing pro-
vides protection against contact with current-carrying components via double insulation (pro-
tection class II). The fan heater is also available with an optional fixed-point thermostat as
the CSF 032. These series were designed to accommodate DIN rail or screw mounting.
Heating
CS/CSF 032 Compact PTC Fan Heater 1000 W
||
Heating element PTC resistor - temperature limiting
Overheat protection built-in temperature limiter
Surface temperature max. 176 °F (80 °C), except upper protective grill
at 68 °F (20 °C) ambient temperature
Air outlet temperature max. 257 °F (125 °C), 2” (50 mm) above grill
Axial fan, ball bearing service life 70,000 h at 77 °F (25 °C)
Air flow, free blowing 37 cfm (63 m³/h)
Connection male power insert connector according to IEC320 C18
Fuse 10 A time lag (T) integrated
Housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715, or
screw mount (M5, not included), tightening torque 2 Nm max.
Mounting position air flow directed up
Operating temperature -40 to +140 °F (-40 to +60 °C)
Storage temperature -40 to +158 °F (-40 to +70 °C)
Dimensions 5.9 x 3.5 x 2.6” (150.5 x 88 x 66 mm)
Weight approx. 16.5 oz. (650 g)
Protection class II (double insulated)
Protection type IP20
Approvals UL File No. 234324, VDE
Important note: Connectors and cables for electrical connection are not included with the heater.
Connection cables are available as accessories (see next page).
CS032/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Part No.
DIN rail mount
Part No.
Screw mount Series Operating voltage Heating
capacity1)
Max. current
(inrush)
Switch-off
temperature2)
Switch-on
temperature2)
03200.0-00 03200.0-01 CS 032, no thermostat AC 220-240 V, 50/60 Hz 1000 W 12 A - -
03200.9-00 03200.9-01 CS 032, no thermostat AC 100-120 V, 50/60 Hz 1000 W 18 A - -
03201.0-00 03201.0-01 CSF 032, with thermostat AC 220-240 V, 50/60 Hz 1000 W 12 A 59 °F (15 °C) 41 °F (5 °C)
03201.9-00 03201.9-01 CSF 032, with thermostat AC 100-120 V, 50/60 Hz 1000 W 18 A 77 °F (25 °C) 59 °F (15 °C)
03202.0-00 03202.0-01 CSF 032, with thermostat AC 220-240 V, 50/60 Hz 1000 W 12 A 59 °F (15 °C) 41 °F (5 °C)
03202.9-00 03202.9-01 CSF 032, with thermostat AC 100-120 V, 50/60 Hz 1000 W 18 A 77 °F (25 °C) 59 °F (15 °C)
CS 032 Fan Heater
CSF 032 Fan Heater with Integrated Thermostat
1) at 77 °F (25 °C) ambient temperature
2) tolerance of ± 5 K
Ambient Temperature
Heating Power (W)
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
Lighting
CS/CSF 032 Compact PTC Fan Heater Accessories
CS032A/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Connection cable with female power insert connector according to IEC320 C17
Retaining Clip
Dimensional drawing
Part No. Length
244379 1.0 m
244380 2.0 m
Part No. Note
237009 Suitable for female power insert connection cable 244379 and 244380
Photo: Retaining clip, Part No. 237009
View: back side
Accessories
Technical Data
Compact design
Built-in overheat protection
Integrated adjustable thermostat (optional)
Double insulated plastic housing
The compact CS 030 high performance fan heater prevents formation of condensation and pro-
vides an evenly distributed interior air temperature in enclosures. This fan heater is available
with an optional integrated thermostat for temperature control. The CS 030 was designed as a
stationary unit for the bottom of the enclosure. For panel or DIN rail mount, the CS 130 fan
heater is recommended.
30
6.6” (168 mm)
4.7” (120 mm) 5.7” (145 mm)
5.1” (130 mm)
4.1” (105 mm)
Heating
CS 030 Foot-mount PTC Fan Heater 1200 W
||
Heating element PTC resistor - temperature limiting
Overheat protection built-in temperature limiter
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing 94 cfm (160 m³/h)
Connection 2-pole terminal AWG 14 max. (2.5 mm²) with strain relief,
clamping torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting M5 screws (not included)
Mounting position horizontal
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 4.7 x 5.7 x 6.6” (120 x 145 x 168 mm)
Weight approx. 2.6 lbs. (1.2 kg)
Protection class II (double insulated)
Protection type IP20
CS030/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
LL
NN
M
Wiring diagram
Part No. Heating capacity1) Operating voltage Max. current (inrush) Setting range Approvals
03060.0-00 1200 W AC 230 V, 50/60 Hz 13.0 A 0 to 60 °C UL File No. E234324, VDE
03060.0-01 1200 W AC 230 V, 50/60 Hz 13.0 A none (no integrated controls) UL File No. E234324, VDE
03060.9-00 1200 W AC 120 V, 50/60 Hz 16.0 A 32 to 140 °F UL File No. E234324
03060.9-01 1200 W AC 120 V, 50/60 Hz 16.0 A none (no integrated controls) UL File No. E234324
1) at 68 °F (20 °C) ambient temperature
Ambient Temperature
Heating Power (W)
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
Technical Data
Compact design
Built-in overheat protection
Integrated adjustable thermostat (optional)
Double insulated plastic housing
Panel or DIN rail mounting
The compact CS 130 high performance fan heater prevents formation of condensation and pro-
vides an evenly distributed interior air temperature in enclosures. This fan heater is available
with an optional integrated thermostat for temperature control. The CS 130 was designed as a
stationary unit for panel or DIN rail mounting. For foot mounting on the bottom of an enclosure,
the CS 030 fan heater is recommended.
30
5.6” (142 mm)
2.6” (67 mm)
4.7” (120 mm)
7.2” (182 mm)
6.3” (160 mm)
Heating
CS 130 Panel-mount PTC Fan Heater 1200 W
||
Heating element PTC resistor - temperature limiting
Overheat protection built-in temperature limiter
Axial fan, ball bearing service life 50,000 h at 77 °F (25 °C)
Air flow, free blowing 94 cfm (160 m³/h)
Connection 2-pole terminal AWG 14 max. (2.5 mm²) with strain relief,
clamping torque 0.8 Nm max.
Housing plastic, UL 94V-0, black
Mounting clip for 35 mm DIN rail, EN 60715 or M6 screws (not included)
Mounting position horizontal
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 4.7 x 6.3 x 7.2” (120 x 160 x 182 mm)
Weight approx. 2.6 lbs. (1.2 kg)
Protection class II (double insulated)
Protection type IP20
CS130/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Part No. Heating capacity1) Operating voltage Max. current (inrush) Setting range Approvals
13060.0-00 1200 W AC 230 V, 50/60 Hz 13.0 A 0 to 60 °C UL File No. E234324, VDE
13060.0-01 1200 W AC 230 V, 50/60 Hz 13.0 A none (no integrated controls) UL File No. E234324, VDE
13060.9-00 1200 W AC 120 V, 50/60 Hz 16.0 A 32 to 140 °F UL File No. E234324
13060.9-01 1200 W AC 120 V, 50/60 Hz 16.0 A none (no integrated controls) UL File No. E234324
1) at 68 °F (20 °C) ambient temperature
LL
NN
M
Wiring diagram
Ambient Temperature
Heating Power (W)
-40 °C -20 °C 0 °C 20 °C 40 °C
-40 °F -4 °F 32 °F 68 °F 104 °F
Technical Data
Heating
||
CREx020/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
CREx 020 Explosion-proof Heater 50 & 100 W
Large convection surface
Maintenance free
DIN rail mountable
The CREx 020 convection heaters are used in areas with explosion hazard to maintain minimum
operating temperatures to help prevent failure of electronic components caused by condensa-
tion and corrosion.
Explosion protection according to EN LCIE (Laboratoire Central des Industries Electriques)
Conformity certificate 01 ATEX 6073/03, LCIE N°06 ATEX Q8011, IECEx LCI 07. 0021
Heating element high performance cartridge
Heater body aluminum profile, black anodized
Connection Si HF - JZ 3 x AWG 18 (0.75 mm²), length 3.3 ft (1 m)
Connection PE 4 mm²
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Protection class I(grounded)
Protection type IP65
Part No. Operating voltage Heating capacity Ex protection type Surface temperature Length (L) Weight (approx.)
02010.0-00 AC 230-240 V 50 W d IIC T5 - Ex tD A21 IP6x T100°C 212 °F (100 °C) 5.9” (150 mm) 2.9 lbs. (1.3 kg)
02010.0-01 AC 110-120 V 50 W d IIC T5 - Ex tD A21 IP6x T100°C 212 °F (100 °C) 5.9” (150 mm) 2.9 lbs. (1.3 kg)
02011.0-00 AC 230-240 V 100 W d IIC T4 - Ex tD A21 IP6x T100°C 275 °F (135 °C) 7.1” (180 mm) 3.3 lbs. (1.5 kg)
02011.0-01 AC 110-120 V 100 W d IIC T4 - Ex tD A21 IP6x T100°C 275 °F (135 °C) 7.1” (180 mm) 3.3 lbs. (1.5 kg)
4.65” (118 mm)
2.7” (69 mm)
5.9 / 7.1” (150 / 180 mm)
DIN clip can alternatively
be mounted to other side
Type: CREx 050W
EEx d IIC T5
AC 230-240V / 50W
Art. Nr. 02010.0-00
L.C.I.E. 98.E 6110
Serial No.:
France S.A.
Ne pas ouvrir sous tension.
Attendre 15 min. avant ouverture.
Nicht unter Spannung öffnen.
Vor öffnen 15 min. warten.
Do not open while energized.
Wait 15 min. before opening.
Technical Data
Ventilating
||
FF018/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Very low noise
Minimal mounting depth
Functional design
Time-saving installation
Weather and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior temperature of
an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus
expelling heated internal air. The resulting air flow prevents formation of localized heat pock-
ets and protects the electronic components from overheating. The plastic used for the hood of
this filter fan series is highly weather resistant, as well as impact and UV light resistant.
Axial fan, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, plastic rotor
Connection 2 wires w/cage clamps, AWG 14 (2.5 mm²), length 4” (100 mm)
Housing (filter fan and exhaust filter) Plastic, UL 94V-0, light grey
Hood (filter fan and exhaust filter) Plastic, UL 94V-0, light grey;
weather and UV light resistant according to UL 746C (f1)
Mounting frame with double-sided industrial adhesive for mounting to the
outside of enclosure; certain operating circumstances may
make the additional use of screws necessary; cut-out
template included
Filter media rating G4 acc. to DIN EN 779, filtering degree 94 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH, reusable - can be cleaned by
washing or vacuuming
Operating / Storage temperature +14 to +158 °F (-10 to +70 °C) / -40 to +158 °F (-40 to 70 °C)
Protection class I(grounded)
Protection type IP55 (according to VDE), UL Type 1
Note: Using fine filter mat F5 increases the protection to UL Type 12 but reduces the air flow
Part No. Operating
voltage
Air volume,
free blowing
Air volume
with
exhaust filter
Power
consumption
Average noise level
(DIN EN ISO 4871)
Mounting
depth
Enclosure
cut-out
Weight
(approx.) Approvals
01800.0-00 AC 230 V, 5 0Hz1) 12 cfm (21 m³/h ) 9 cfm (16 m³/h) 13 W 31 dB (A) 1.8” (45 mm) 3.8 x 3.8” 1.3 lbs. (0.6 kg) UL File No. E234324, VDE
01800.0-01 AC 120 V, 60 Hz 14 cfm (24 m³/h) 11 cfm (18 m³/h) 13 W 31 dB (A) 1.8” (45 mm) 3.8 x 3.8” 1.3 lbs. (0.6 kg) UL File No. E234324
01801.0-00 AC 230 V, 5 0Hz1) 32 cfm (55 m³/h) 25 cfm (42 m³/h) 15 W 40 dB (A) 2.3” (58 mm) 4.9 x 4.9” 2.2 lbs. (1.0 kg) UL File No. E234324, VDE
01801.0-01 AC 120 V, 60 Hz 37 cfm (63 m³/h) 28 cfm (48 m³/h) 15 W 40 dB (A) 2.3” (58 mm) 4.9 x 4.9” 2.2 lbs. (1.0 kg) UL File No. E234324
01802.0-00 AC 230 V, 5 0Hz1) 60 cfm (102 m³/h) 40 cfm (68 m³/h) 15 W 39 dB (A) 3.4” (86 mm) 6.9 x 6.9” 2.9 lbs. (1.3 kg) UL File No. E234324, VDE
01802.0-01 AC 120 V, 60 Hz 69 cfm (117 m³/h) 46 cfm (78 m³/h) 15 W 39 dB (A) 3.4” (86 mm) 6.9 x 6.9” 2.9 lbs. (1.3 kg) UL File No. E234324
Special features
The self-adhesive seal of the mounting frame prevents dust and water from entering the cabinet.
Functional design of the intake and exhaust fan hoods very effectively prevents direct infiltration of falling water and dust. The advantage is that the filter mat does not rapidly become contaminated with dirt
and therefore does not need to be exchanged as often.
The air channeling makes the filter fan particularly quiet in operation.
All filter fan models are also available with integrated airflow monitor.
The direction of air flow can easily be switched by reversing the axial fan.
EMC versions and other voltages are available upon request.
FF 018 Filter Fan 14 - 69 cfm
Enclosure ventilation using a filter fan and exhaust filter
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
Ventilating
FF 018 Filter Fan 14 - 69 cfm
FF018/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Time-saving assembly and maintenance
STEGO's filter fans are easily installed by one person from outside the cabinet.
1.) Make cut-out in the cabinet wall. The cut edge of the cabinet opening should be free of
dirt, filings and grease. A template for the enclosure cut-out is included with the filter fan.
2.) Remove protective film from the sealing strips on the mounting frame. Press mounting
frame into the cabinet opening. The frame stays permanently in the cabinet.
3.) Electrically connect the axial fan using the cage clamp connectors. Push the unit into the
mounting frame. Affix using screws if necessary.
4.) Insert the filter mat in the hood. Clip on. Finished.
To change the filter mat, simply remove the filter hood, insert the new mat and snap the hood
back again. No tools are required. Maintenance of the fan can easily be performed without
removing the mounting frame (2).
Installation sketch
Dimensional Drawing
5.1”
5.3”
1.8”
3.8”
6.2”
6.7”
2.3”
4.9”
8.2”
8.9”
3.4”
6.9”
1.4” 1.6” 2.0”
Filter mat 3.5 x 3.5” (89 x 89 mm) 4.6 x 4.6” (118 x 118 mm) 6.6 x 6.6” (168 x 168 mm)
G4 (1 packing unit = 3 pcs.) Part No. 08600.0-00 Part No. 08601.0-00 Part No. 08602.0-00
F5 (1 packing unit = 3 pcs.) Part No. 08603.0-00 Part No. 08604.0-00 Part No. 08605.0-00
Part No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type Approvals
11800.0-00 0.6” (16 mm) 3.8 x 3.8” 0.6 lbs. (0.3 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55* UL File No. E234324
11801.0-00 0.6” (16 mm) 4.9 x 4.9” 0.8 lbs. (0.4 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55* UL File No. E234324
11802.0-00 0.6” (16 mm) 6.9 x 6.9” 1.3 lbs. (0.6 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55* UL File No. E234324
Drilling template for mounting frame
*according to VDE
5.4” (137 mm)
5.4” (137 mm)
Ø1/8” (3mm)
7.4” (188 mm)
7.4” (188 mm)
4.3” (109 mm)
4.3” (109 mm)
Ø1/8” (3mm)
Ø1/8” (3mm)
EF 118 Exhaust Filter
FM 086 Filter Mats
Technical Data
8.2” (209 mm)
8.9” (226 mm)
6.8” (172 mm)
3.7” (95 mm)
2.0”
(50 mm)
2.0”
(50 mm)
6.8” (172 mm)
Ventilating
FF018-136/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
High air volume
Functional design
Time-saving installation
Weather and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior temperature of
an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus
expelling heated internal air. The resulting air flow prevents formation of localized heat pock-
ets and protects the electronic components from overheating. The plastic used for the hood of
this filter fan series is highly weather resistant, as well as impact and UV light resistant.
Axial fan, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, metal rotor
Connection 3-pole term., AWG 14 (2.5 mm²), clamping torque 0.8 Nm max.
Housing (filter fan and exhaust filter) Plastic, UL 94V-0, light grey
Hood (filter fan and exhaust filter) Plastic, UL 94V-0, light grey;
weather and UV light resistant according to UL 746C (f1)
Mounting frame with double-sided industrial adhesive for mounting to the
outside of enclosure; certain operating circumstances may
make the additional use of screws necessary; cut-out
template included
Filter media rating G4 acc. to DIN EN 779, filtering degree 94 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH, reusable - can be cleaned by
washing or vacuuming
Operating / Storage temperature -13 to +140 °F (-25 to +60 °C)
Protection class I(grounded)
Protection type IP55 (according to VDE), UL Type 1
Note: Using fine filter mat F5 increases the protection to UL Type 12 but reduces the air flow
Filter mat 6.6 x 6.6” (168 x 168 mm)
G4 (1 packing unit = 3 pcs.) Part No. 08602.0-00
F5 (1 packing unit = 3 pcs.) Part No. 08605.0-00
FM 086 Filter Mats
*according to VDE
Part. No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type Approvals
11802.0-00 0.6” (16 mm) 6.9 x 6.9” 1.3 lbs. (0.6 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55* UL File No. E234324
Part No. Operating
voltage
Air volume,
free blowing
Air volume
with exhaust filter
Power
consumption
Average noise level
(DIN EN ISO 4871)
Mounting
depth
Enclosure
cut-out
Weight
(approx.) Approvals
01804.0-00 AC 230 V, 50 Hz1) 118 cfm (200 m³/h) 74 cfm (125 m³/h) 45 W 52 dB (A) 3.7” (95 mm) 6.9 x 6.9” 3.7 lbs. (1.7 kg) UL File No. E234324
01804.0-01 AC 120 V, 60 Hz 136 cfm (230 m³/h) 84 cfm (143 m³/h) 39 W 52 dB (A) 3.7” (95 mm) 6.9 x 6.9” 3.7 lbs. (1.7 kg) UL File No. E234324
7.4” (188 mm)
7.4” (188 mm)
Ø1/8”
(3 mm)
Filter Fan
View from rear
Drilling template for mounting frame
FF 018 Filter Fan
EF 118 Exhaust Filter
FF 018 Filter Fan 136 cfm
||
Exhaust Filter
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
Technical Data
11.2” (284 mm)
2.6”
(65 mm)
9.8” (250 mm)
1.8”
(45 mm)
0.9”
(22 mm)
9.8” (250 mm)
1.8”
(45 mm)
Ventilating
FF018-202/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Minimal mounting depth
High air volume
Functional design
Time-saving installation
Weather and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior temperature of
an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus
expelling heated internal air. The resulting air flow prevents formation of localized heat pock-
ets and protects the electronic components from overheating. Four integrated axial fans pro-
vide a particularly high and uniform air circulation which contributes to higher reliability. The
plastic used for the hood of this filter fan series is highly weather and UV light resistant.
Axial fan, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, plastic rotor
Connection 3-pole term., AWG 14 (2.5 mm²), clamping torque 0.8 Nm max.
Housing (filter fan and exhaust filter) Plastic, UL 94V-0, light grey
Hood (filter fan and exhaust filter) Plastic, UL 94V-0, light grey;
weather and UV light resistant according to UL 746C (f1)
Mounting frame with double-sided industrial adhesive for mounting to the
outside of enclosure; certain operating circumstances may
make the additional use of screws necessary; cut-out
template included
Filter media rating G4 acc. to DIN EN 779, filtering degree 94 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH, reusable - can be cleaned by
washing or vacuuming
Operating / Storage temperature +14 to +158 °F (-10 to +70 °C) / -40 to +158 °F (-40 to +70 °C)
Protection class I(grounded)
Protection type IP55 (according to VDE), UL Type 1
Note: Using fine filter mat F5 increases the protection to UL Type 12 but reduces the air flow
FM 086 Filter Mats
*according to VDE
EF 118 Exhaust Filter
FF 018 Filter Fan
FF 018 Filter Fan 202 cfm
4 axial fans
View from rear
Filter fan
Exhaust filter
10.4” (263 mm)
10.4” (263 mm)
Ø1/8”
(3 mm)
||
Drilling template for
mounting frame
Filter mat 9.7 x 9.7” (247 x 247 mm)
G4 (1 packing unit = 3 pcs.) Part No. 08608.0-00
F5 (1 packing unit = 3 pcs.) Part No. 08609.0-00
Part. No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type
11803.0-00 0.9” (22 mm) 9.8 x 9.8” 2.2 lbs. (1.0 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55*
Part No. Operating
voltage
Air volume,
free blowing
Air volume
with exhaust filter
Power
consumption
Average noise level
(DIN EN ISO 4871)
Mounting
depth
Enclosure
cut-out
Weight
(approx.) Approvals
01803.0-00 AC 230 V, 50 Hz1) 177 cfm (300 m³/h) 135 cfm (230 m³/h) 60 W 53 dB (A) 2.6” (65 mm) 9.8 x 9.8” 7.3 lbs. (3.3 kg) UL File No. E234324
01803.0-01 AC 120 V, 60 Hz 202 cfm (345 m³/h) 155 cfm (264 m³/h) 60 W 53 dB (A) 2.6” (65 mm) 9.8 x 9.8” 7.3 lbs. (3.3 kg) UL File No. E234324
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
Technical Data
4.2”
(107 mm)
11.2” (284 mm)
1.8”
(45 mm)
9.8” (250 mm)
0.9”
(22 mm)
9.8” (250 mm)
1.8”
(45 mm)
Ventilating
FF018-371/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
High air volume
Functional design
Time-saving installation
Weather and UV resistant
Filter fans are used to provide an optimum climate in enclosures. The interior temperature of
an enclosure can be reduced by channeling cooler filtered outside air into the enclosure thus
expelling heated internal air. The resulting air flow prevents formation of localized heat pock-
ets and protects the electronic components from overheating. The plastic used for the hood of
this filter fan series is highly weather and UV light resistant.
Axial fan, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, metal rotor
Connection 3-pole term., AWG 14 (2.5 mm²), clamping torque 0.8 Nm max.
Housing (filter fan and exhaust filter) Plastic, UL 94V-0, light grey
Hood (filter fan and exhaust filter) Plastic, UL 94V-0, light grey;
weather and UV light resistant according to UL 746C (f1)
Mounting frame with double-sided industrial adhesive for mounting to the
outside of enclosure; certain operating circumstances may
make the additional use of screws necessary; cut-out
template included
Filter media rating G4 acc. to DIN EN 779, filtering degree 94 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH, reusable - can be cleaned by
washing or vacuuming
Operating / Storage temperature -13 to +158 °F (-25 to +70 °C)
Protection class I(grounded)
Protection type IP55 (according to VDE), UL Type 1
Note: Using fine filter mat F5 increases the protection to UL Type 12 but reduces the air flow
*according to VDE
FF 018 Filter Fan 373 cfm
Filter fan
View from rear Exhaust filter
10.4” (263 mm)
10.4” (263 mm)
Ø1/8”
(3 mm)
Drilling template for mounting frame
||
Filter mat 9.7 x 9.7” (247 x 247 mm)
G4 (1 packing unit = 3 pcs.) Part No. 08608.0-00
F5 (1 packing unit = 3 pcs.) Part No. 08609.0-00
FM 086 Filter Mats
Part. No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type
11803.0-00 0.9” (22 mm) 9.8 x 9.8” 2.2 lbs. (1.0 kg) G4 acc. to DIN EN 779, filtering degree 94 % IP55*
Part No. Operating
voltage
Air volume,
free blowing
Air volume
with exhaust filter
Power
consumption
Average noise level
(DIN EN ISO 4871)
Mounting
depth
Enclosure
cut-out
Weight
(approx.) Approvals
01805.0-00 AC 230 V, 50 Hz1) 324 cfm (550 m³/h) 177 cfm (300 m³/h) 64 W 52 dB (A) 4.2” (107 mm) 9.8 x 9.8” 5.9 lbs. (2.7 kg) UL File No. E234324
01805.0-01 AC 120 V, 60 Hz 373 cfm (633 m³/h) 203 cfm (345 m³/h) 85 W 52 dB (A) 4.2” (107 mm) 9.8 x 9.8” 5.9 lbs. (2.7 kg) UL File No. E234324
FF 018 Filter Fan
EF 118 Exhaust Filter
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
Technical Data
0.7”
(18 mm)
6.5” (165 mm)
8.8” (224 mm)
5.6” (142 mm)
+0.2
7.3” (185 mm)
+0.2
2.6” (65 mm)2.4” (62 mm)
4.9” (125 mm)
Ventilating
||
FF01821/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
FF 01821 Outdoor Filter Fan 14 cfm
Quick and easy filter change
Lockable outer door
Impact resistant
Weather and UV resistant
This filter fan can be used in outdoor enclosures where warm air has to be dissipated. To clean
and exchange the filter mat, it is only necessary to open the lockable door of the outdoor hood
eliminating the need to allow interior access to the enclosure. A protection type of IP55 is
achieved due to the special design of the hood and the use of fine filter mats. The plastic used
for the hood of this filter fan is highly weather and UV light resistant.
Axial fan, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, plastic rotor
Connection 2 wires w/cage clamps, AWG 14 (2.5 mm²), length 4” (100 mm)
Filter fan and exhaust filter housing high impact ASA plastic, light grey
burning behavior according to UL 94H-B;
high resistance to weather and UV light
Mounting frame with double-sided industrial adhesive for mounting to the
outside of enclosure; certain operating circumstances may
make the additional use of screws necessary; cut-out
template included
Filter media rating F5 acc. to DIN EN 779, filtering degree 98 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH
Operating / Storage temperature +14 to +158 °F (-10 to +70 °C) / -40 to +158 °F (-40 to +70 °C)
Protection class I(grounded)
Protection type IP55
Note: EMC version and other voltages are available upon request
The hood is attached permanently to the enclosure from the inside using provided screws. Filter mats can be
easily changed from outside the enclosure through the lockable door in the hood.
Filter mat 4.6 x 4.6” (118 x 118 mm)
F5 (1 packing unit = 3 pcs.) Part No. 08604.0-00
FFM 086 Filter Mats
Part No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type
11821.0-00 0.6” (16 mm) 4.9 x 4.9” 1.6 lbs. (0.6 kg) F5 acc. to DIN EN 779, filtering degree 98 % IP55
EF 11821 Exhaust Filter
Part No. Operating
voltage
Air volume,
free blowing
Power
consumption
Average noise level
(DIN EN ISO 4871) Mounting depth Enclosure
cut-out
Weight
(approx.) Approvals
01821.0-00 AC 230 V, 50 Hz1) 12 cfm (20 m³/h) 15 W 40 dB (A) 2.4” (62 mm) 4.9 x 4.9” 2.6 lbs. (1.2 kg) UL File No. E234324
01821.0-02 AC 120 V, 60 Hz 14 cfm (23 m³/h) 15 W 40 dB (A) 2.4” (62 mm) 4.9 x 4.9” 2.6 lbs. (1.2 kg) UL File No. E234324
FF 01821 Outdoor Filter Fan
Outdoor Filter Fan
View from rear Outdoor Exhaust Filter
5.4” (137 mm)
5.4” (137 mm)
Ø0.12”
(3 mm)
Drilling template for
mounting frame
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
13.9” (354 mm)
9.8” (250 mm)
2.0”
(52 mm)
2.9”
(73 mm)
2.9”
(73 mm)
4.2”
(107 mm)
13.9” (354 mm)
9.8” (250 mm)
Ventilating
||
RFF018/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
RFP 018 Roof Filter Fan 177 - 338 cfm
Roof filter fans and roof exhaust filters are used in enclosures from which warm air must be
diverted due to increased heat development. The ready-to-connect and low-noise roof filter fan
is used to expel warm air from within the enclosure. Alternatively, the roof exhaust filter pro-
vides passive ventilation. The RFP 018 series comes in two versions: one utilizes four small
axial fans, improving reliability and maintaining continuous operations even if one of the fans
should fail; the second uses a larger single high capacity fan.
Axial fans, ball bearing service life min. 50,000 h at 77 °F (25 °C) and 65 %RH
aluminum fan body, plastic rotor
Connection 3-pole term., AWG 14 (2.5 mm²), clamping torque 0.8 Nm max.
Housing Plastic, UL 94V-0, light grey;
weather and UV light resistant according to UL 746C (f1)
Filter mat G3 acc. to DIN EN 779, filtering degree 85 %
Filter material synthetic fiber with progressive construction, temperature
resistant to 212 °F, self-extinguishing class F1;
moisture resistant to 100 %RH, reusable - can be cleaned by
washing or vacuuming
Operating / Storage temperature dependent on fan type
Protection class I(grounded)
Protection type IP32
Approvals VDE (230V only)
Important note: For reasons of pressure compensation, the roof filter fan must always be operated in combi-
nation with another filter fan (e.g. Part No. 01803.0-00) or a passive intake filter (e.g. Part No. 11803.0-00).
Filter mat 11.1 x 11.1” (282 x 282 mm)
G3 (1 packing unit = 3 pcs.) Part No. 08613.0-01
FM 086 Filter Mats
Part No. Mounting depth Enclosure cut-out Weight (approx.) Filter mat Protection type
11860.0-00 0.43” (11 mm) 9.8 x 9.8” 2.2 lbs. (1.0 kg) G3 acc. to DIN EN 779, filtering degree 85 % IP32
REP 118 Roof Exhaust Filter
Part No. Operating
voltage
Air volume, free blowing
(w/ G3 filter mat)
Power
consumption
Average noise level
(DIN EN ISO 4871) Mounting depth Enclosure
cut-out
Weight
(approx.)
01860.0-00 AC 230 V, 50 Hz1) 177 cfm (300 m³/h) - 4 fans 68 W 55 db (A) 2.0” (52 mm) 9.8 x 9.8” 7.3 lbs. (3.3 kg)
01860.0-02 AC 120 V, 60 Hz 203 cfm (345 m³/h) - 1 fan 60 W 55 db (A) 2.0” (52 mm) 9.8 x 9.8” 5.7 lbs. (2.6 kg)
01861.0-00 AC 230 V, 50 Hz1) 294 cfm (500 m³/h) - 4 fans 64 W 67 db (A) 4.2” (107 mm) 9.8 x 9.8” 7.3 lbs. (3.3 kg)
01861.0-02 AC 120 V, 60 Hz 338 cfm (575 m³/h) - 1 fan 85 W 67 db (A) 4.2” (107 mm) 9.8 x 9.8” 5.7 lbs. (2.6 kg)
RFP 018 Roof Filter Fan
Very low noise
Minimal mounting depth
High air volume
High reliability
Time-saving installation
Ø0.12”
(3 mm)
Enclosure cut out
10.1” (256 mm)
9.8” (250 mm)
Hole
centers
Use included template for precise cut-out dimensions
Technical Data
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
2.9”
(73 mm)
0.4”
(11 mm)
9.8” (250 mm)
Roof Exhaust Filter
Technical Data
13” (330 mm)
17.8” (452 mm)
16.9” (430 mm)
19" (482.6 mm)
8.2” (208 mm)
1.7”
(43.6 mm)
1.25”
(31.8 mm)
18.3” (465.1 mm)
Ventilating
||
LE019/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
LE 019 19" Fan Tray 286 - 1017 cfm
High air volume
Long service life
Easy installation and connection
Function control light
Optional integrated thermostat
The LE 019 is a compact high performance fan tray for forced circulation of air in enclosures and
for cooling of 19" rack mount applications. Natural convection is improved and the formation of
hot zones is prevented. Also available with integrated thermostat (see photo).
Axial fans, ball bearing service life 50,000 h at 77 °F (25 °C) and 65 %RH
fan body aluminium, rotor plastic
Material front panel aluminium, bright anodised
casing steel sheet, electrogalvanized
Optical indicator integrated in front panel
Connection power inlet on rear of casing, plug included (no cable)
Mounting position horizontal (direction of air upward)
Operating / Storage temperature -4 to +158 °F (-20 to +70 °C)
Protection type IP20
Protection class I(grounded)
Approvals UL File No. E234324
Note
The use of a thermostat, whether integrated or external, is recommended.
When using a fan tray with integrated thermostat, an additional thermostat (e.g. KT 011 Part No. 01141.9-00)
may be used if it is desired to switch a signal device should the enclosure interior temperature rise above a set
limit (e.g. in case of fan failure).
For models without integrated thermostat, the use of a dual thermostat (e.g. ZR 011 Part No. 01176.0-00) pro-
vides the same overheat protection, i.e. one thermostat to control the fan tray operation, one thermostat for a
signal device.
Part No. Model No. of
fans
Operating
voltage
Air flow,
free blowing
Power
consumption
Average noise level
(DIN EN ISO 4871) Speed (rpm-1)Static
pressure Weight (approx.)
01930.0-00 w/out thermostat 3AC 230 V, 50 Hz1) 286 cfm (486 m³/h) 45 W 55 db (A) 2600 min-1 (50 Hz) 74 Pa 6.6 lbs. (3.0 kg)
01930.1-00 w/ thermostat (0 to 60°C) 3AC 230 V, 50 Hz1) 286 cfm (486 m³/h) 45 W 55 db (A) 2600 min-1 (50 Hz) 74 Pa 7.5 lbs. (3.4 kg)
01931.0-00 w/out thermostat 3AC 120 V, 60 Hz 339 cfm (576 m³/h) 45 W 55 db (A) 2900 min-1 (60 Hz) 88 Pa 6.6 lbs. (3.0 kg)
01931.1-00 w/ thermostat (0 to 60°C) 3AC 120 V, 60 Hz 339 cfm (576 m³/h) 45 W 55 db (A) 2900 min-1 (60 Hz) 88 Pa 7.5 lbs. (3.4 kg)
01940.0-00 w/out thermostat 6AC 230 V, 50 Hz1) 572 cfm (972 m³/h) 90 W 57 db (A) 2600 min-1 (50 Hz) 74 Pa 11.7 lbs. (5.3 kg)
01940.1-00 w/ thermostat (0 to 60°C) 6AC 230 V, 50 Hz1) 572 cfm (972 m³/h) 90 W 57 db (A) 2600 min-1 (50 Hz) 74 Pa 12.5 lbs. (5.7 kg)
01941.0-00 w/out thermostat 6AC 120 V, 60 Hz 678 cfm (1152 m³/h) 90 W 57 db (A) 2900 min-1 (60 Hz) 88 Pa 11.7 lbs. (5.3 kg)
01941.1-00 w/ thermostat (0 to 60°C) 6AC 120 V, 60 Hz 678 cfm (1152 m³/h) 90 W 57 db (A) 2900 min-1 (60 Hz) 88 Pa 12.5 lbs. (5.7 kg)
01950.0-00 w/out thermostat 9AC 230 V, 50 Hz1) 858 cfm (1458 m³/h) 135 W 58 db (A) 2600 min-1 (50 Hz) 74 Pa 17.2 lbs. (7.8 kg)
01950.1-00 w/ thermostat (0 to 60°C) 9AC 230 V, 50 Hz1) 858 cfm (1458 m³/h) 135 W 58 db (A) 2600 min-1 (50 Hz) 74 Pa 17.4 lbs. (7.9 kg)
01951.0-00 w/out thermostat 9AC 120 V, 60 Hz 1017 cfm (1728 m³/h) 135 W 58 db (A) 2900 min-1 (60 Hz) 88 Pa 17.2 lbs. (7.8 kg)
01951.1-00 w/ thermostat (0 to 60°C) 9AC 120 V, 60 Hz 1017 cfm (1728 m³/h) 135 W 58 db (A) 2900 min-1 (60 Hz) 88 Pa 17.4 lbs. (7.9 kg)
1) air volume increases by 15% when operating AC 230 V filter fans at 60 Hz
Technical Data
Ventilating
DA 284 Vent Plug
DA284/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
UL Type 1, 4, 4X & IP66 protection
Waterproof membrane
Easy to install
Two sizes - M40 & M12
Pressure differentials in a hermetically sealed enclosure are a result of the heat generated by
electrical and electronic components in the enclosure, as well as the fluctuation of the outside
temperature. In the case of negative pressure or vacuum, for example, dust and humidity can
enter the enclosure through the door seal.
The DA 284 Vent Plug provides a protected enclosure environment for valuable and crucial com-
ponents with a UL 4X rated degree of protection. A waterproof membrane inside the device
allows air and humidity to leave the enclosure. Conversely, it only allows dry air into the enclo-
sure while not allowing humidity and dust from the outside to enter.
Part No. Model Thread length
(depth in enclosure) Protection type Air permeability1) 1 packing unit Weight (approx.)
28405.0-00 M40 x 1.5 approx. 16 mm IP66 (EN 60529) / IPX9K (EN 40050-9) 1200 liters/hr 2 pieces 3.2 oz. (90 g) total
28406.0-00 M12 x 1.5 approx. 10 mm IP66 (EN 60529) 120 liters/hr 2 pieces 0.14 oz. (4 g) total
Mounting thread with nut (see below), torque 10 Nm max.
Material plastic, PA66, light grey
Sealing NBR gasket
Filter waterproof membrane
Operating / Storage temperature -49 to +158 °F (-45 to 70 °C)
Protection type see below
Agency approvals UL File No. E234324
Environmental rating Type 1, 4 and 4X
Installation
Make cut-out in enclosure wall of 1.58” (40 - 40.2 mm) for size M40 or 0.48” (12 - 12.2 mm) for size M12, and
mount vent plug with nut. Make sure that the sealing gasket is placed on the outer side of the enclosure. For
optimal pressure compensation, it is recommended to use two devices on opposite sides towards the top of
the enclosure.
1) at a pressure difference of min. 70 mbar
Photo: DA 284, M40
Dimensional drawing: DA 284, M40
Dimensional drawing: DA 284, M12
(drawing is not proportional to M40)
Photo: DA 284, M12
Technical Data
High degree of protection (IP66)
Semipermeable membrane
Corrosion resistant
Easy to install
Two sizes - M40 & M12
Pressure differentials in a hermetically sealed enclosure are a result of the heat generated by
electrical and electronic components in the enclosure, as well as the fluctuation of the outside
temperature. In the case of negative pressure or vacuum, for example, dust and humidity can
enter the enclosure through the door seal.
The DA 284S Stainless Steel Vent Plug provides a protected enclosure environment for valu-
able and crucial components with an IP66 rated degree of protection. A waterproof membrane
inside the device allows air and humidity to leave the enclosure. Conversely, it only allows dry
air into the enclosure while not allowing humidity and dust from the outside to enter.
Ventilating
DA 284S Stainless Steel Vent Plug
Part No. Model Thread length
(depth in enclosure) Protection type Air permeability1) 1 packing unit Weight (approx.)
28401.0-00 M40 x 1.5 approx. 9 mm IP66 (EN 60529) / IPX9K (EN 40050-9) 1200 liters/hr 1 piece 5.6 oz. (160 g)
28402.0-01 M12 x 1.5 approx. 4 mm IP66 (EN 60529) 120 liters/hr 1 piece 0.6 oz. (17 g)
Mounting thread with nut, torque 10 Nm max.
Material stainless steel V2A (DIN 1.4305 / AISI 303)
Sealing NBR gasket
Filter waterproof membrane
Operating / Storage temperature -31 to +158 °F (-35 to 70 °C)
Protection type see below
Installation
A hole with a diameter of 1.58” (40 - 40.2 mm) is required for installation. Make sure that the sealing gasket
is placed on the outer side of the enclosure. For optimal pressure compensation, it is recommended to use two
devices on opposite sides towards the top of the enclosure.
DA284S/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
2.28” (58 mm)
0.79” (20 mm)
1.22” (31 mm)
M40 x 1.5
40 mm)Ø1.57” (Ø
Dimensional drawing: DA 284S, M40
Photos: DA 284S, M40
1) at a pressure difference of min. 70 mbar
Technical Data
Ventilating
DA084/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
DA 084 Vent Plug
High degree of protection (IP55)
Easy to install
It has become increasingly important to provide a protected enclosure environment for valuable
and crucial electrical and electronic components. In a tightly closed enclosure, pressure differ-
entials can occur during extreme temperature variations, such as day/night operation. When
this occurs, the risk of dust and humidity ingression into the control panel increases dramatical-
ly. The specially designed DA 084 vent plug permits a controlled change in pressure and can
easily be installed in any enclosure. The vent plug is suitable for the use in enclosures and elec-
trical cabinets in accordance with DIN EN 62208.
Mounting PG 29 thread with union nut, torque 10 Nm max.
Mounting position vertical*
Material plastic, UL 94V-0
Sealing NBR gasket
Air Interface Approx. 2.8 in2(7 cm2)
Operating / Storage temperature -49 to +158 °F (-45 to 70 °C)
Dimensions Ø 2.58” x 1.2” (Ø 65.5 x 30.5 mm)
* Protection type is restricted to IP54 if mounting position is not vertical
Installation
A hole with a diameter of 1.46” (37 mm) is required for mounting. Make sure that the sealing gasket is placed
on the outer side panel of the enclosure. For optimal pressure compensation, it is recommended to use two
devices on opposite sides towards the top of the enclosures.
Part No. Protection type 1 packing unit Weight (approx.)
08400.9-01 IP55 1 piece 1.1 oz. (31 g)
0.61” (15.5 mm)
1.2” (30.5 mm)
2.58” (65.6 mm)
Ø1.46” (37 mm)
0.61” (15.5 mm)
Technical Data
Energy saving LED technology
Wide voltage range
Integrated power unit
Magnet or screw mount
Wide variety of connections
On/off switch or motion sensor
The LED 025 light series is suitable for all types of panels and enclosures, especially where
space is at a premium. These lights have a very long service life due to the use of LED tech-
nology. They are available with powerful non-slip rubberized magnets allowing them to be
easily positioned in any steel enclosure. Screw mounting is also available as an option. The
power output allows up to 10 lights to be connected to each other (daisy chain) with both the
input and output plugs snap-locking into place.
Lighting
LED 025 Light
||
Power consumption max. 5 W (~ 75 W incandescent bulb)
Luminosity 290 Lm
Lamp type LED, 120° angle of radiation
light color - daylight, color temperature - 6,500 K
Service life 60,000 hrs. at 68 °F (20 °C)
Connection 2-pole plug with snap lock
AC: max. 2.5 A / AC 240 V, white cable
DC: max. 2.5 A / DC 60 V, blue cable
Housing plastic, transparent
Mounting magnet or M5 screws (not included), 9.8” (250 mm) centers;
screw torque 2 Nm max.
Operating temperature -22 to +140 °F (-30 to +60 °C)
Storage temperature -40 to +185 °F (-40 to +85 °C)
Dimensions magnet mount - 13.8 x 1.3 x 1.3” (351 x 34 x 32 mm)
screw mount - 13.8 x 1.4 x 1.3” (351 x 36 x 32 mm)
Protection class II (double insulated)
Protection type IP20
Accessories input and output plug, cable for supply or connection
Approvals UL File No. E234324, VDE
Note available with a 19” front panel
LED025/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Part No. - magnet mount Part No. - screw mount Operating voltage Switch type Weight
02540.0-00 02540.0-01 AC 100-240 V, 50/60 Hz (min. AC 90 V, max. AC 265 V) on/off switch 4.8 oz. (135 g)
02540.1-00 02540.1-01 DC 24-48 V (min. DC 20 V, max. DC 60 V) on/off switch 4.8 oz. (135 g)
02541.0-00 02541.0-01 AC 100-240 V, 50/60 Hz (min. AC 90 V, max. AC 265 V) PIR motion sensor 1) 5.0 oz. (140 g)
02541.1-00 02541.1-01 DC 24-48 V (min. DC 20 V, max. DC 60 V) PIR motion sensor 1) 5.0 oz. (140 g)
LED 025 Light with magnet mount
LED 025 Light with screw mount
1) Passive Infrared (PIR) motion sensor is factory pre-set to turn the light off 6 minutes after all motion ceases
On/off switch light w/magnet mount
Screw mount end view
Motion sensor light w/magnet mount
Screw mount end view
Magnet mount end view
Magnet mount end view
Lighting
LED 025 Light - Accessories
LED025A/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Photo: Connection cable, Part No. 244357
Extension cable with 2 connectors for daisy chain (input & output) connection
Input / output connectors
Connection cable with input connector and wire leads
Part No. Model Length Voltage Color Approvals
244357 connection cable 2 x AWG 16 with input connector 2.0 m AC connector: white - cable: white UL, VDE
244361 connection cable 2 x AWG 16 with input connector 2.0 m DC connector: blue - cable: white UL, VDE
Photo: Connection cable, Part No. 244359
Part No. Model Length Voltage Color Approvals
244359 extension cable 2 x AWG 16 with 2 connectors 1.0 m AC connectors: white - cable: white UL, VDE
244363 extension cable 2 x AWG 16 with 2 connectors 1.0 m DC connectors: blue - cable: white UL, VDE
Part No. Model Voltage Color Approvals
264057 input connector AC white UL, VDE
264058 output connector AC white UL, VDE
264059 input connector DC blue UL, VDE
264060 output connector DC blue UL, VDE
Photo: Input connector, Part No. 264057 Photo: Output connector, Part No. 264058
1
The lights are easily connected via quick connection plugs or extension cables -- up to 10 lights can be daisy-chained this way. The snap-lock connectors ensure a stable electrical connection even
when subjected to vibration.
Connection example
1
2
2 2
Part No. - magnet mount Part No. - screw mount Operating voltage Switch type Weight
02540.0-00-0003 02540.0-01-0003 AC 100-240 V, 50/60 Hz (min. AC 90 V, max. AC 265 V) on/off switch 4.8 oz. (135 g)
02540.1-00-0003 02540.1-01-0003 DC 24-48 V (min. DC 20 V, max. DC 60 V) on/off switch 4.8 oz. (135 g)
02541.0-00-0003 02541.0-01-0003 AC 100-240 V, 50/60 Hz (min. AC 90 V, max. AC 265 V) PIR motion sensor 1) 5.0 oz. (140 g)
02541.1-00-0003 02541.1-01-0003 DC 24-48 V (min. DC 20 V, max. DC 60 V) PIR motion sensor 1) 5.0 oz. (140 g)
1) Passive Infrared (PIR) motion sensor is factory pre-set to turn the light off 6 minutes after all motion ceases
Light kit with input connector included
Technical Data
Lighting
||
SL025/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
SL 025 Slimline Light
Compact design
Electronic ballast
Optional integrated receptacle
Screw or magnet mount
Long-life energy saving lamp
On/off switch or motion sensor
The SL 025 light was designed to fit in tight spaces in enclosures. It features an optional inte-
grated receptacle so that electrical devices (e.g. power tools) can be easily plugged in when
needed. The standard light can be screw mounted in a variety of positions, or the light can be
fitted with an available magnet mount. The motion sensor version was designed to eliminate
the need for a door switch.
Power consumption 11 W (~ 75 W incandescent bulb)
Luminosity 900 Lm
Lamp type compact fluorescent, 2G7 base, electronic ballast
Service life 10,000 hrs.
Switch (for light only) on/off switch or PIR motion sensor1)
Connection 3-pole terminal AWG 16 max. (1.5 mm²) with strain relief only
(cable not included), clamping torque 0.8Nm max.
Housing plastic, UL 94V-0, light grey
Mounting M5 screws (not included), 11.8” (300 mm) hole distance or
optional attached magnet (see part nos. below)
Operating temperature -4 to +122 °F (-20 to +50 °C)
Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 13.6 x 3.6 x 1.6” (345 x 91 x 40 mm)
Weight approx. 0.9 lbs. (400 g), 1.3 lbs (600 g) with magnet
Protection type IP20
Note DC 24-48 V available upon request
Part No. with
On/Off Switch
Part No. with
Motion Sensor Model Operating voltage Receptacle Rec. max.
current Protection class Approvals
02520.0-00 02520.0-03 without magnet AC 230 V, 50/60 Hz Germany/Russia 16 A I(grounded) VDE
02520.1-00 02520.1-03 with magnet AC 230 V, 50/60 Hz Germany/Russia 16 A I(grounded) VDE
02521.0-00 02521.0-03 without magnet AC 230 V, 50/60 Hz France/Poland 16 A I(grounded) VDE
02521.1-00 02521.1-03 with magnet AC 230 V, 50/60 Hz France/Poland 16 A I(grounded) VDE
02522.0-00 02522.0-03 without magnet AC 230 V, 50/60 Hz Switzerland 10 A I(grounded) VDE
02522.1-00 02522.1-03 with magnet AC 230 V, 50/60 Hz Switzerland 10 A I(grounded) VDE
02523.0-00 02523.0-03 without magnet AC 230 V, 50/60 Hz UK/Ireland 13 A I(grounded) VDE
02523.1-00 02523.1-03 with magnet AC 230 V, 50/60 Hz UK/Ireland 13 A I(grounded) VDE
02524.0-01 02524.0-04 without magnet AC 120 V, 50/60 Hz USA/Canada 15 A I(grounded) UL File No. E234324
02524.1-01 02524.1-04 with magnet AC 120 V, 50/60 Hz USA/Canada 15 A I(grounded) UL File No. E234324
02527.0-00 02527.0-04 without magnet AC 230 V, 50/60 Hz none -II (double insulated) UL File No. E234324, VDE
02527.1-00 02527.1-04 with magnet AC 230 V, 50/60 Hz none -II (double insulated) UL File No. E234324, VDE
02527.0-10 02527.0-12 without magnet AC 120 V, 50/60 Hz none -II (double insulated) UL File No. E234324
02527.1-10 02527.1-12 with magnet AC 120 V, 50/60 Hz none -II (double insulated) UL File No. E234324
Magnet (optional)
13.6” (345 mm)
3.6” (91mm)
1.6” (40mm)
11.8” (300 mm)
0.5” (12.5 mm)
0.8” (20 mm)
1) The Passive Infrared (PIR) motion sensor detects the motion of the enclosure door being opened and automat-
ically turns on the light. The sensor is factory pre-set to turn the light off 6 minutes after all motion ceases. The
motion sensor does not detect movement through glass, allowing for installation in enclosures with glass doors.
Note: electrical cable not included
Technical Data
Lighting
||
SL025-19/11-12/US
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
SL 025 19” Rack-mount Slimline Light
Compact design
Electronic ballast
Optional integrated receptacle
Long-life energy saving lamp
On/off switch
This SL 025 light is suitable for 19" rack mounting, e.g. for keyboards. Because of the flat design
of the light, only one rack unit in height (“1U”) is needed. Additionally, it is fitted with a reflec-
tor which serves as a glare shield, thereby illuminating the area below the light only.
The light also features an optional integrated receptacle, allowing for the use of additional elec-
trical devices, such as power tools.
Power consumption 11 W (~ 75 W incandescent bulb)
Luminosity 900 Lm
Lamp type compact fluorescent, 2G7 base, electronic ballast
Service life 10,000 hrs.
Switch (for light only) on/off switch (PIR motion sensor also available)
Connection 3-pole terminal AWG 16 max. (1.5 mm²) with strain relief only
(cable not included), clamping torque 0.8 Nm max.
Housing plastic, UL 94V-0, light grey
Mounting max. M6 screws (not included)
Mounting bracket aluminum, with cable bushing
Operating temperature -4 to +122 °F (-20 to +50 °C)
Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions lamp - 13.6 x 3.6 x 1.6” (345 x 91 x 40 mm), total length - 19”
Weight approx. 1.1 lbs. (500 g)
Protection type IP20
Note DC 24-48 V available upon request
1.7” (44 mm)
19” (483 mm)
3.5” (88 mm)
Note: electrical cable not included
Part No. Operating voltage Receptacle Receptacle max. current Protection class Approvals
02520.0-02 AC 230 V, 50/60 Hz Germany/Russia 16.0 A I(grounded) VDE
02521.0-02 AC 230 V, 50/60 Hz France/Poland 16.0 A I(grounded) VDE
02522.0-02 AC 230 V, 50/60 Hz Switzerland 10.0 A I(grounded) VDE
02523.0-02 AC 230 V, 50/60 Hz UK/Ireland 13.0 A I(grounded) VDE
02524.0-05 AC 120 V, 50/60 Hz USA/Canada 15.0 A I(grounded) UL File No. E234324
02527.0-02 AC 230 V, 50/60 Hz none -II (double insulated) UL File No. E234324, VDE
02527.0-11 AC 120 V, 50/60 Hz none -II (double insulated) UL File No. E234324
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
Technical Data
Lighting
||
KL025/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
KL 025 Compact Enclosure Light
Magnet or DIN rail mounting
Energy-saving lamp
Integrated receptacle
On/off switch
Power consumption see table below
Luminosity 900 Lm
Lamp type compact fluorescent, G23 base, inductive ballast
Service life 5,000 hrs.
Switch on/off switch (for light only)
Connection 3-pole terminal AWG 14 max. (2.5 mm²) with strain relief only
(cable not included), clamping torque 0.8 Nm max.
Housing plastic, light grey
Mounting magnet mounting or on 35 mm DIN rail, EN 60715
Operating temperature -4 to +122 °F (-20 to +50 °C)
Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 13.98 x 2.56 x 2.76” (355 x 65 x 70 mm)
Weight approx. 2.2 lbs (1.0 kg)
Protection type IP20
The compact KL 025 light was designed for use in industrial enclosures and control cabinets. A
strong magnet allows simple and quick installation and flexibility for various mounting posi-
tions. The light also features an optional integrated receptacle so that electrical devices can
easily be plugged in when needed.
Part No. Operating voltage Receptacle Power consumption Receptacle Max. Current Protection class Approvals
02500.0-14 AC 230 V, 60 Hz Germany 11 W (~ 75 W incandescent bulb) 16 A I(grounded) VDE
02500.0-21 AC 120 V, 60 Hz none 9 W (~ 60 W incandescent bulb) -II (double insulated) -
02505.9-02 AC 120 V, 60 Hz USA/Canada 9 W (~ 60 W incandescent bulb) 15 A I(grounded) -
Drawing shows mounting on two 7 inch long pieces of 35mm DIN rail.
Technical Data
Lighting
||
DL026/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
DL 026 Dual Light
Versatile – base lamp or hand lamp
Long-life energy saving lamp
On/off switch or motion sensor
The DL 026 dual light is available with on/off switch or motion sensor (the motion sensor ver-
sion was designed to eliminate the need for a door switch). The lamp is removable from its
base and, with the use of an optional additional power cord, can be used as a hand lamp.
This versatile light was also designed to include a variety of mounting options.
Power consumption 20 W (~ 100 W incandescent bulb)
Luminosity 1000 Lm
Lamp type compact fluorescent, E27 base, electronic ballast
Service life 10,000 hrs.
Switch on/off push switch or PIR motion sensor1)
Connection 6-pole terminal, AWG 14 max (2.5 mm²) - torque 0.5 Nm max.
for hard wiring of 1 light or 2 lights in parallel
Housing plastic, UL 94V-0, light grey
Standard mounting (included) screw mounting on 35 mm DIN rail or sheet metal
Optional mounting with self-adhesive or magnet mounting plates (see below)
Mounting position variable
Operating temperature -4 to +122 °F (-20 to +50 °C)
Storage temperature -49 to +158 °F (-45 to +70 °C)
Weight approx. 1.3 lbs. (600 g)
Protection class II (double insulated)
Protection type IP20
Accessories see below
Part No. Operating voltage Switch type
02600.0-00 AC 230 V, 50/60 Hz on/off
02600.9-00 AC 120 V, 50/60 Hz on/off
02601.0-00 AC 230 V, 50/60 Hz motion sensor
02601.9-00 AC 120 V, 50/60 Hz motion sensor
2.6” (67 mm)
3.93” (100 mm)
15.6” (396 mm)
(1) Standard screw mounting to DIN rail
(2) 2 self-adhesive (Part No. 09515.0-00) or magnet (Part No. 09516.0-00) mounting plates
(3) Self-adhesive light holder with hook and 6 ft. power cord (AC 230 V - Part No. 03410.0-00,
AC 120 V - Part No. 03411.0-00). By using the holder/power cord kit, the light can be used as a hand lamp.
1) The Passive Infrared (PIR) motion sensor detects the motion of the enclosure door being opened and automat-
ically turns on the light. The sensor is factory pre-set to turn the light off 3 minutes after all motion ceases. The
motion sensor does not detect movement through glass, allowing for installation in enclosures with glass doors.
Light with on/off switch Light with motion sensor
Note: electrical cable not included
Technical Data
Lighting
||
DL026HL/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
DL 026 Hand Lamp
Long-life energy saving lamp
Wall-mount lamp holder
Power consumption 20 W (~ 100 W incandescent bulb)
Luminosity 1000 Lm
Lamp type compact fluorescent, E27 base, electronic ballast
Service life 10,000 hrs.
Connection integrated power cable (6 ft.) with US or Euro plug
Housing plastic, UL 94V-0, light grey
Mounting screws or self-adhesive mounting plate (included)
Mounting position variable
Operating temperature -4 to +122 °F (-20 to +50 °C)
Storage temperature -49 to +158 °F (-45 to +70 °C)
Weight approx. 1.3 lbs. (600 g)
Protection class II (double insulated)
Protection type IP20
Part No. Operating voltage Plug type
02610.0-00 AC 230 V, 50/60 Hz Euro
02610.9-00 AC 120 V, 50/60 Hz US
41
3.3” (84 mm)
2.7” (68 mm)
13.3” (337 mm)
Technical Data
Electrical Receptacles
SD 035 Enclosure Receptacle
SD035/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Quick connections
Available with or without fuse
DIN rail mountable
The DIN rail mounted electrical receptacle can be quickly fitted and connected in enclosures
allowing the use of auxiliary products such as hand lamps and power tools. The unit is available
with and without fuse, and in many world outlet standards.
Connection 3 cage clamps for solid and stranded wire AWG 20-14
(0.5-2.5 mm²)
Housing plastic, UL 94V-0, light grey
Mounting clip for 35 mm DIN rail, EN 60715
Mounting position vertical
Operating / Storage temperature -49 to +158 °F (-45 to 70 °C)
Dimensions 3.6 x 2.4 x 1.9” (92 x 62 x 48 mm)
Weight approx. 7.1 oz. (200 g)
Protection class I(grounded)
Protection type IP20
Part No. Operating Voltage max. Socket Model Nominal Current Approvals
03500.0-00 AC 250 V Germany/Russia (1) with fuse* 6.3 A -
03500.0-01 AC 250 V Germany/Russia (1) without fuse 16.0 A -
03501.0-00 AC 250 V France/Poland (2) with fuse* 6.3 A -
03501.0-01 AC 250 V France/Poland (2) without fuse 16.0 A -
03502.0-00 AC 250 V Switzerland (3) with fuse* 6.3 A -
03502.0-01 AC 250 V Switzerland (3) without fuse 10.0 A -
03503.0-00 AC 250 V UK/Ireland (4) with fuse* 6.3 A -
03503.0-01 AC 250 V UK/Ireland (4) without fuse 13.0 A -
03504.0-00 AC 125 V USA/Canada (5) with fuse* 6.3 A UL File No. E222026
03504.0-01 AC 125 V USA/Canada (5) without fuse 15.0 A UL File No. E222026
03505.0-00 AC 250 V Italy (6) with fuse* 6.3 A -
03505.0-01 AC 250 V Italy (6) without fuse 16.0 A -
(1)
N
F
U
S
E
N
F
U
S
E
N
F
U
S
E
N
F
U
S
E
N
F
U
S
E
N
F
U
S
E
(2) (3)
(4) (5) (6)
N
F
U
S
E
2.4” (62 mm)
3.6” (92 mm)
1.9” (48 mm)
* fuse Ø 5 x 20 mm
Technical Data
Variety of uses
Locking door
High impact resistance
Weather and UV resistant
The access door on the multi-purpose protective cover is equipped with a lock enabling easy
access while providing security from unauthorized persons. The cover utilizes a labyrinth seal
for protection against dirt and moisture, and the unit is permanently attached to the enclosure
from the inside.
11 12 23 24
30
20
10
0
40
50
60 °C
30
20
10
0
40
50
60
1
2
3
4
5
12345
1
4
7
*
2
5
8
0
3
6
9
#
Accessories
MA 086 Multi-purpose Protective Cover
Part No. Weight
08611.0-00 approx. 0.9 lbs. (0.4 kg)
Housing High impact ASA plastic, light grey
burning behavior according to UL 94H-B;
high resistance to weather and UV light
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Dimensions 8.8 x 6.5 x 2.6” (224 x 165 x 65 mm)
Protection type IP20
MA086/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Protection for ventilation openings
(i.e. pressure compensation)
As a cover for thermostats
and regulators
As a tamper-proof cover for
electronic input devices
Protection for electronic locks and
security system keypads
Protection for power outlets Cover and protection for data
interfaces
Application examples
Bottom view
Technical Data
Accessories
STEGOFIX/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Part No. 1 packing unit Weight (approx.)
09510.0-01 5 pieces 2.1 oz. (60 g) total / 0.42 oz. (12 g) per piece
STEGO FIX Self-adhesive Mounting Aid
Load 1.1 lbs. (500 g) after a 24 hour waiting period*
Mounting self-adhesive (non-aging, high-performance adhesive strip)
Material plastic UL 94V-0, black
Hole pattern 0.5” distance, Ø 0.14” (12.8 mm; Ø 3.6 mm)
Operating / Storage temperature -49 to +158 °F (-45 to 70 °C)
Dimensions 1.7 x 1.5 x 0.55” (43 x 38 x 14 mm)
*depending on the conditions of use (e.g. surface condition, size of the device to be mounted, etc.) higher
loads can be achieved.
Installation
STEGOFIX can only be mounted on smooth surfaces, e.g. metals, lacquered surfaces and plastics (except
polyethylene, polypropylene and rubber). The surfaces must be dry and free from dust, oil, separating agents
and other contamination.
STEGOFIX is a small aid specially designed to make mounting of smaller DIN rail mountable
components easier. It can be used whenever the installation of a DIN rail is impractical, or
when there is not enough space left in an enclosure.
Because of its industrial grade self-adhesive it can be installed much easier and quicker than a
conventional DIN rail, without the effort of hole drilling and screw mounting. This is especially
practical for subsequent changes or additions in an already equipped enclosure.
STEGOFIX can hold components up to 1.1 lbs in weight. Some of the many applications include
the mounting of timing relays, series terminals, thermostats, cable channels and even small
heaters. In addition, DIN rails can be mounted simply by using several STEGOFIX units.
If the weight of attached components exceeds the load limit, or if a more secure mounting is
desired, (e.g. on rough surfaces), it can also be screw-mounted. All that is necessary to install
STEGOFIX is a smooth and clean surface. The initial adhesive power is 40%, and after 24 hours,
it has its full holding power of 1.1 lbs.
Application examples
1.7” (43 mm)
1.5” (38 mm)
0.55” (13.5 mm)
0.5” (12.8 mm)
1.1” (27.5 mm)
Technical Data
IP66 / IP67 / IP69K protection
Good drainage performance
Easy to install
Weather and UV resistant
Condensation can occur in enclosures with high protection types by variations in temperature.
The use of the DD 084 drainage device allows the removal of the condensate without losing
the maximum IP66 protection type.
The specific characteristic of the water permeable membrane ensures the drainage of the con-
densate via capillary action. The unique construction also prohibits the ingression of splash
water into the enclosure. Additionally, the drainage device effectively provides pressure com-
pensation with variations in temperature.
Accessories
DD 084 Drainage Device
Mounting thread M50 x 1.5 with nut (wrench size 60 mm)
torque 6 Nm max.
Mounting position vertical, lowest point
Depth in enclosure approx. 0.7” (17.5 mm)
Material plastic, UL 94V-0, RAL 7022,
weather and UV light resistant according to UL 746C (f1)
Water entry height 0 mm (at 0.5 mm wall thickness)
Sealing NBR gasket
Water flow-through approx. 200 ml/h at 5 mm water column
Dimensions Ø 2.36 x 1.9” (60 x 49.5 mm)
Operating / Storage temperature -49 to +158 °F (-45 to +70 °C)
Installation
Make cut-out in enclosure bottom of Ø 2.0 inches (50.5+0.5 mm) and mount the drainage device with nut.
Make sure that the sealing gasket is placed on the outer side of the enclosure.
DD084/11-12/US
Specifications are subject to change without notice. Suitability of this product for its intended use and any associated risks must be determined by the end customer/ buyer in its final application.
STEGO, Inc. · 1395 South Marietta Parkway · Building 800 · Marietta, GA 30067 · Tel: (770) 984-0858 · Fax: (770) 984-0615
Toll free: 1-888-783-4611 (US & Canada only) · www.stegousa.com
Part No. Protection type Enclosure wall thickness 1 packing unit Weight
08410.0-00 IP66 / IP67 (EN 60529) / IP69K (EN 40050-9) 0.02 - 0.22” (0.5 - 5.5 mm) 1 piece approx. 2 oz. (60 g)
Mounting position
HEATER CALCULATION SHEET
Project: Project No.:
Follow Steps 1-5 to determine the heating requirement of an enclosure (US units - left column, metric - right)
STEP 1: Determine the Surface Area (A) of your enclosure which is exposed to open ai
r
Enclosure Dimensions: height = feet meters
width = feet meters
depth = feet meters
Choose Mounting Option from next page, and calculate the surface area as indicated
A = ________ ft2or ________ m2
STEP 2: Choose the Heat Transmission Coefficient (k) for your enclosure's material of construction
painted steel = 0.511 W/(ft2•K) 5.5 W/(m2•K)
stainless steel = 0.344 W/(ft2•K) 3.7 W/(m2•K)
aluminum = 1.115 W/(ft2•K) 12 W/(m2•K)
l ti ( i ltd til )
0 325
W/(ft
2
K)
35
W/(
2
K)
plastic (or insulated stainless) = 0.325 W/(ft
2
•K) 3.5 W/(m
2
•K)
k = ________ W/(ft2•K) or ________ W/(m2•K)
STEP 3: Determine the Temperature Differential (
Δ
T)
A. Desired enclosure interior temp. = oFoC
B. Lowest ambient (outside) temp. = oFoC
Subtract B from A = Temp. differential (ΔT) = oFoC
For these calculations, ΔT must be in degrees Kelvin (K). Enter
Δ
T (oC) below
Therefore, divide ΔT (oF) by 1.8 ΔT = ________ Kor ________ K
STEP 4: Determine Heating Power (PV), if any (generated from existing components, i.e. transformer)
PV = ________ Wor ________ W
STEP 5: Calculate the Required Heating Power (PH) for your enclosure based on the above values
If enclosure is located inside: PH = (A x k x
Δ
T) - PV = __________ W
If enclosure is located outside: PH = 2 x (A x k x
Δ
T) - PV = __________ W
Δ
T (oC) = ΔT (K)
W
H
D
ENCLOSURE MOUNTING OPTIONS
and SURFACE AREA CALCULATIONS
1. Free-Standing
Area (A) = 1.8(H x W)
+ 1.8(H x D) + 1.8(W x D)
Area (A) = 1.8(H x W)
+ 1.4(H x D) + 1.8(W x D)
Area (A) = 1.8(H x W)
+ (H x D) + 1.8(W x D)
2. Wall-Mounted
Area (A) = 1.4(H x W)
+ 1.8(H x D) + 1.8(W x D)
Area (A) = 1.4(H x W)
+ 1.4(H x D) + 1.8(W x D)
Area (A) = 1.4(H x W)
+ (H x D) + 1.8(W x D)
3. Ground
Area (A) = 1.8(H x W)
+ 1.8(H x D) + 1.4(W x D)
Area (A) = 1.8(H x W)
+ 1.4(H x D) + 1.4(W x D)
Area (A) = 1.8(H x W)
+ (H x D) + 1.4(W x D)
Area (A) = 1.4(H x W)
+ 1.8(H x D) + 1.4(W x D)
Area (A) = 1.4(H x W)
+ 1.4(H x D) + 1.4(W x D)
Area (A) = 1.4(H x W)
+ (H x D) + 1.4(W x D)
4. Ground & Wall
Mounting Options-06-08/US
FILTER FAN SIZING SHEET
Project: Project No.:
To determine the Filter Fan size for a given enclosure, use the following calculation:
Internal heat load (Pv)
Required air volume (V) = x Air constant (f)
Temperature difference (
Δ
T)
US Metric
STEP 1: Determine the Internal Heat Load of the enclosure (Pv)
Internal heat load, Pv (Watts) = _________ W= ________
_
W
[Note: 1 Watt = 3.413 BTU/hr.]
STEP 2: Determine the Temperature Differential (
Δ
T)
Temperature difference (ΔT) = _________ °F = ________
_
°C = K
[Max. temperature outside enclosure minus max. allowable temperature inside enclosure]
STEP 3: Choose the Air Constant (f)
Air constant (f) = _________ ft3y°F/W min = ________
_
m3yK/W hr
[Based on elevation, see below]
0 - 100 m ⇒ 3.3 ft3y°F/W min or 3.1 m3yK/W hr
100 - 250 m ⇒ 3.4 ft3y°F/W min or 3.2 m3yK/W hr
250 - 500 m ⇒ 3.5 ft3y°F/W min or 3.3 m3yK/W hr
500 - 750 m ⇒ 3.6 ft3y°F/W min or 3.4 m3yK/W hr
750 - 1000 m ⇒ 3.7 ft
3
y°F/W min or 3.5 m
3
yK/W hr
Example: 600 W internal heat load,
Δ
T = 15 K, at 75 m elevation
600 W
V = x 3.3 m3yK/W hr
15 K
V = 132 m3/hr