Features
• Rectangular Light Emitting
Surface
• Excellent for Flush
Mounting on Panels
• Choice of Five Bright Colors
• Long Life: Solid State
Reliability
• Excellent Uniformity of
Light Output
Description
The HLMP-S100, -S201, -5301,
-S400, -S401, -S501, -S600 are
epoxy encapsulated lamps in
rectangular packages which are
easily stacked in arrays or used
for discrete front panel indicators.
Contrast and light uniformity are
enhanced by a special epoxy
diffusion and tinting process.
The HLMP-S100 uses double
heterojunction (DH) absorbing
substrate (AS) aluminum gallium
arsenide (AlGaAs) LEDs to
produce outstanding light output
over a wide range of drive
currents.
2 mm x 5 mm Rectangular
LED Lamps
Technical Data HLMP-S100
HLMP-S201
HLMP-S301
HLMP-S400
HLMP-S401
HLMP-S501
HLMP-S600
Package Dimensions
2
Selection Guide
Luminous Intensity Iv (mcd) at 20 mA
Color Part Number Min. Typ. Max.
AlGaAs Red HLMP-S100 3.4 7.5 –
HER HLMP-S201
HLMP-S201-D00xx 2.1 3.5 –
HLMP-S201-E00xx 3.4 7.5 –
HLMP-S201-EF0xx 3.4 7.5 10.8
Orange HLMP-S400 2.1 3.5 –
HLMP-S401 3.4 7.5 –
Yellow HLMP-S301
HLMP-S301-B00xx 1.4 2.1 –
HLMP-S301-C00xx 2.2 4.0 –
HLMP-S301-CDBxx 2.2 4.0 7.2
Green HLMP-S501
HLMP-S501-C00xx 2.6 4.0 –
HLMP-S501-D00xx 4.2 8.0 –
HLMP-S501-DE0xx 4.2 8.0 13.4
Emerald Green[1] HLMP-S600-A00xx 1.0 3.0 –
Note:
1. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.
Part Numbering System
HLMP - S x xx - x x x xx
Mechanical Option
00: Bulk
02: Tape & Reel, Straight Leads
DG: Ammo Pack
Color Bin Options
0: Full Color Bin Distribution
B: Color Bins 2 & 3 only
Maximum Iv Bin Options
0: Open (no max. limit)
Others: Please refer to the Iv Bin Table
Minimum Iv Bin Options
Please refer to the Iv Bin Table
Brightness Level
00: Less Brightness
01: Higher Brightness
Color Options
1: AlGaAs Red
2: GaP HER
3: GaP Yellow
4: GaP Orange
5: GaP Green
6: GaP Emerald Green
3
Sym. Description Device HLMP- Min. Typ. Max. Units Test Conditions
2θ1/2 Included Angle All 110 Deg. IF = 20 mA
Between Half See Note 1
Luminous
Intensity Points
λPEAK Peak Wavelength AlGaAs Red 645 nm Measurement at
High Efficiency Red 635 Peak
Orange 600
Yellow 583
Green 565
Emerald Green 558
λdDominant AlGaAs Red 637 nm See Note 2
Wavelength High Efficiency Red 626 Time const, e-t/τs
Orange 602
Yellow 585
Green 569
Emerald Green 560
τsSpeed of AlGaAs Red 30 ns
Response High Efficiency Red 90
Orange 280
Yellow 90
Green 500
Emerald Green 3100
C Capacitance AlGaAs Red 30 pF VF = 0; f = 1 MHz
High Efficiency Red 11
Orange 4
Yellow 15
Green 18
Emerald Green 35
RθJ-PIN Thermal All 260 °C/W Junction to Cathode
Resistance Lead at Seating
Plane
VFForward Voltage AlGaAs Red 1.6 1.8 2.2 V IF = 20 mA
HER/Orange 1.5 1.9 2.6
Yellow 1.5 2.1 2.6
Green/Emerald 1.5 2.2 3.0
Green
VRReverse Break- All 5.0 V IR = 100 µA
down Voltage
ηVLuminous AlGaAs Red 80
Efficacy High Efficiency Red 145
Orange 380 lumens/ See Note 3
Yellow 500 watt
Green 595
Emerald Green 656
Electrical/Optical Characteristics at TA = 25°C
Notes:
1. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.
2. The dominant wavelength, λd, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the
color of the device.
3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/ηv, where Iv is the luminous intensity in candelas and ηv
is the luminous efficacy in lumens/watt.
4. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.
4
Figure 1. Relative Intensity vs. Wavelength.
Green/
AlGaAs High Efficiency Emerald
Parameter Red Red/Orange Yellow Green Units
Peak Forward Current 300 90 60 90 mA
Average Forward Current[1] 20 25 20 25 mA
DC Current[2] 30 30 20 30 mA
Transient Forward Current[3] 500 mA
(10 µsec Pulse)
LED Junction Temperature 110 110 110 110 °C
Operating Temperature Range -20 to +100 -20 to +100
-55 to +100 -55 to +100 °C
Storage Temperature Range -55 to +100 -55 to +100
Lead Soldering Temperature
[1.6 mm (0.063 in.) below 260°C for 5 seconds
seating plane]
Notes:
1. See Figure 5 to establish pulsed operating conditions.
2. For AlGaAs Red, Red, Orange, and Green series derate linearly from 50°C at 0.5 mA/°C. For Yellow series derate linearly from 50°C at
0.34 mA/°C.
3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED
die and wire bond. It is not recommended that the device be operated at peak currents beyond the peak forward current listed in the
Absolute Maximum Ratings.
Absolute Maximum Ratings at TA = 25°C
ORANGE AlGaAs RED
HIGH EFFICIENCY RED
WAVELENGTH – nm
RELATIVE INTENSITY
1.0
0.5
0
500 550 600 650 700
YELLOW
EMERALD GREEN
HIGH
PERFORMANCE
GREEN
T = 25° C
A
5
Figure 4. Relative Efficiency
(Luminous Intensity per Unit Current)
vs. LED Peak Current. ηv (300 mA) for
AlGaAs Red = 0.7.
Figure 2. Forward Current vs.
Forward Voltage Characteristics. VF
(300 mA) for AlGaAs Red = 2.6 Volts
Typical.
Figure 3. Relative Luminous Intensity
vs. DC Forward Current.
Figure 5. Maximum Tolerable Peak Current vs. Peak Duration.
(IPEAK MAX Determined from Temperature Derated IDC MAX).
Figure 6. Relative Luminous Intensity vs. Angular Displacement.
6
Intensity Bin Limits
Intensity Range (mcd)
Color Bin Min. Max.
D 2.4 3.8
E 3.8 6.1
F 6.1 9.7
G 9.7 15.5
H 15.5 24.8
I 24.8 39.6
J 39.6 63.4
K 63.4 101.5
L 101.5 162.4
M 162.4 234.6
N 234.6 340.0
Red/Orange O 340.0 540.0
P 540.0 850.0
Q 850.0 1200.0
R 1200.0 1700.0
S 1700.0 2400.0
T 2400.0 3400.0
U 3400.0 4900.0
V 4900.0 7100.0
W 7100.0 10200.0
X 10200.0 14800.0
Y 14800.0 21400.0
Z 21400.0 30900.0
B 1.6 2.5
C 2.5 4.0
D 4.0 6.5
E 6.5 10.3
F 10.3 16.6
G 16.6 26.5
H 26.5 42.3
I 42.3 67.7
J 67.7 108.2
K 108.2 173.2
Yellow L 173.2 250.0
M 250.0 360.0
N 360.0 510.0
O 510.0 800.0
P 800.0 1250.0
Q 1250.0 1800.0
R 1800.0 2900.0
S 2900.0 4700.0
T 4700.0 7200.0
U 7200.0 11700.0
V 11700.0 18000.0
W 18000.0 27000.0
7
Intensity Bin Limits, continued
Intensity Range (mcd)
Color Bin Min. Max.
A 1.1 1.8
B 1.8 2.9
C 2.9 4.7
D 4.7 7.6
E 7.6 12.0
F 12.0 19.1
G 19.1 30.7
H 30.7 49.1
I 49.1 78.5
J 78.5 125.7
Green/ K 125.7 201.1
Emerald Green L 201.1 289.0
M 289.0 417.0
N 417.0 680.0
O 680.0 1100.0
P 1100.0 1800.0
Q 1800.0 2700.0
R 2700.0 4300.0
S 4300.0 6800.0
T 6800.0 10800.0
U 10800.0 16000.0
V 16000.0 25000.0
W 25000.0 40000.0
Maximum tolerance for each bin limit is ±18%.
Color Categories
Lambda (nm)
Color Category # Min. Max.
9 552.5 555.5
Emerald Green 8 555.5 558.5
7 558.5 561.5
6 561.5 564.5
6 561.5 564.5
5 564.5 567.5
Green 4 567.5 570.5
3 570.5 573.5
2 573.5 576.5
1 582.0 584.5
3 584.5 587.0
Yellow 2 587.0 589.5
4 589.5 592.0
5 592.0 593.0
1 597.0 599.5
2 599.5 602.0
3 602.0 604.5
Orange 4 604.5 607.5
5 607.5 610.5
6 610.5 613.5
7 613.5 616.5
8 616.5 619.5
www.semiconductor.agilent.com
Data subject to change.
Copyright © 2001 Agilent Technologies, Inc.
September 24, 2001
Obsoletes 5988-0381EN
5988-4202EN
Tolerance for each bin limit is ±0.5 nm.
Note:
All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent
representative for further clarification/information.
Mechanical Option Matrix
Mechanical Option Code Definition
00 Bulk Packaging, minimum increment 500 pcs/bag
02 Tape & Reel, straight leads, minimum increment 1300 pcs/bag
DG Ammo Pack, straight leads with minimum increment 2K/pack
