I P 6 7 D -S U B Co nnec tor s Part Number Creator 6 S T D 0 9 S A M 9 9 B 3 O X Product Line 6 = Shell brass tin plated with die-cast frame 4* = Shell brass tin plated with plastic frame or without frame 8* = Shell stainless steel with or without die-cast frame 9* = Shell stainless steel with plastic frame * on request Variations STD = D-SUBMINIATURE, Standard HDD = D-SUBMINIATURE, High Density Position for STD 09 = 9 pos. 15 = 15 pos. 25 = 25 pos. 37 = 37 pos. = 50 pos. 50 Position for HDD 15 = 15 pos. 26 = 26 pos. 44 = 44 pos. 62 = 62 pos. 78 = 78 pos. Contact type = Plug connector P S = Socket connector A = Adapter Quality class for contacts A = Quality class 3 B = Quality class 2 = Quality class 1 C = 50 mating cycles = 200 mating cycles = 500 mating cycles Termination M = Solder cup R = Solder pin, straight T = Solder pin, angled, .189" U = Solder pin, angled, .276" Z = Solder pin, angled, .465" Y = Solder pin, angled, .220" A = Adapter 4.80 mm 7.00 mm 11.8 mm 5.60 mm (high density design only) Capacitance = Without filter for STD and HDD 99 Mounting style = Riveted for wire assembly shell without sealing frame A1 B2 = M3 threaded insert = 4-40 UNC threaded insert B3 = M3 front spacer B4 = 4-40 UNC front spacer B5 = 4-40 UNC front spacer and rear mounting stud B7 = M3 threaded lock B8 B9 = 4-40 UNC front spacer E1 = M3 threaded rear spacer with PCB clip .063" 1.60 mm OX 2| 2 = Standard E2 S1 S2 S3 S4 R1 R2 R3 R4 = Threaded rear spacer with PCB clip, PCB 1,60 mm = Metal bracket, M3 threaded insert = Metal bracket, 4-40 UNC threaded insert = Metal bracket, M3 threaded insert and PCB clip = Metal bracket, 4-40 UNC threaded insert and PCB clip = Metal bracket, M3 threaded insert = Metal bracket, 4-40 UNC threaded insert = Metal bracket, M3 threaded insert and PCB clip = Metal bracket, 4-40 UNC threaded insert and PCB clip I P67 D-SUB C o n n e c t o r s Technical Data Materials D-Subminiature, Standard 9, 15, 25, 37 and 50 position D-Subminiature, High Density 15, 26, 44, 62 and 78 position Insulator Polyester GF UL94 V-0 Contacts CU alloy Contact plating Gold plated over nickel Shell Brass tin plated (Standard) Stainless steel on request Mechanical and electrical characteristics Test voltage U eff NN 1000 V Working voltage 125 V 60 V depending on isolation coordination (refer to DIN VDE 0110 IEC 664-1) Current rating 7.5 A (UL) Contact resistance 5 A (CSA,VDE) 5 G contact - contact contact - earth Operating temperature Mating and unmating forces Quality class 2.5 A (CSA) max. 10 m prior to stressing, R max. 10 m after stressing per DIN 41652, Part 2 Insulation resistance Clearance and creepage distance 3 A (UL,VDE) .004" 1.0 mm .047" 1.2 mm .024" 0.6 mm - 25 C to + 105 C 9 pos. 15 pos. 25 pos. 37 pos. 50 pos. 30 N 50 N 83 N 123 N 167 N 15 pos. 26 pos. 44 pos. 62 pos. 78 pos. 50 N 84 N 120 N 70 N 200 N A = Quality class 3 = 50 mating cycles B = Quality class 2 = 200 mating cycles C = Quality class 1 = 500 mating cycles Technical alterations are subject to change without notice. 2| 3 I P 6 7 D- S U B C o nnectors IP-Code figure definitions 1. Code figure 0 1 2 3 4 5 6 2. Code figure Definition Not protected Protected against access to hazardous parts by the back of the hand. Protected against fixed foreign objects O 1.969" 50 mm. Protected against access to hazardous parts with a finger. Protected against fixed foreign objects O .492" 12.5 mm. Protected against access to hazardous parts with a tool. Protected against fixed foreign objects O .098" 2.5 mm. Protected against access to hazardous parts with a wire. Protected against fixed foreign objects O .039" 1 mm. Protected against access to hazardous parts with a wire. Dust protected. Remark Ingress of dust is not completely blocked. But dust may not penetrate to the extent that satisfactory operation of the device or safety is impaired. Protected against access to hazardous parts with a wire. Dustproof. No ingress of dust. Definition 0 1 2 3 Not protected Protected against dropper. Protected against dropper when the shell is tipped as much as 15. Protected against spray water 4 Protected against splash water 5 6 7 Protected against jets of water. Protected against strong jets of water. Protected against the effects of temporary submersion in water. 8 Protected against the effects of continuous submersion in water. 9k Protected against water from high-pressure or steam cleaning. Remark Up to 60 of either side of the vertical, such spray water shall have no harmful effects. On the shell from all directions, no harmful effects shall be incurred. Water may not ingress in a volume that would cause harmful effects when the shell is submerged in water for 30 min at a depth of 1 m. Water may not ingress in a volume that would cause harmful effects when the shell is continuously submerged in water under conditions agreed between manufacturer and user. However, these conditions must be more stringent than those described under code figure 7. Explanation to spray water protected (IP) systems and their environment. This system, described in IEC 60529, was developed to represent standard values for respective protection: a) Contact with, and ingress of, fixed foreign objects b) The ingress of liquids to which the inside is to be exposed. The first digit describes the level of protection for life, contacting objects and the intrusion of foreign bodies. The second digit describes the level of protection against the ingress of liquids. The larger the first and second digits are, the greater afforded protection is, e.g. IP55 must also meet the requirements of all lower protection levels, such as IP22, IP23, IP34 and IP54. 2| 4 I P67 D-SUB C o n n e c t o r s Mating conditions Float mount tolerance guide Rigid mount tolerance guide Rigid mount vertical to tolerance guide Panel cut-out Rear panel mounting IP67 D-SUB Connectors Shell size A 0.1 B 1 2 3 4 5 20.50 28.80 42.50 59.10 56.30 20.90 29.20 42.90 59.40 57.00 0.1 C 0.1 25.00 33.30 47.04 63.50 61.10 Front panel mounting IP67 D-SUB Connectors D 0.1 11.40 11.40 11.40 11.40 14.10 E 0.1 13.00 13.00 13.00 13.00 15.80 2| 5 I P 6 7 D - S U B C o nnectors Panel Mounting Front panel mounting Rear panel mounting The hex bolts illustrated here (4-40 UNC or M3 threads) are included in the delivery complement of every connector with a sealing frame. The length of this spacer has been selected to accommodate a panel thickness of .063"/1.6 mm such that it does not extend beyond the plug-in height. Furthermore, the hex bolts outside threads are shorter than standard hex bolts. Material: stainless steel. 2| 6 I P 6 7 D - S U B C o nne ctors Solder profile Connector Type Preheating Duration max. Solder bath Temperature max. Terminal Immersion Time Filter D-SUB 100C 30s 260C 5s Combo D-SUB Filter 120C 120s 260C 5s Filter D-SUB Water Resistant 100C 30s 240C 5s Combo D-SUB Water Resistant 120C 120s 240C 5s D-SUB Water Resistant 120C 120s 240C 5s D-SUB Solid Body Type Water Resistant 150C 180s 265C 8s RJ45 Modular Jack Filtered 150C 180s 265C 8s Filter Plates 150C 180s 265C 8s Recommended wave-solder parameters for CONEC connectors. 2| 24 Solder terminal dipping parameters max. Temperature I P 6 7 D - S U B C o nne ctors PCB layout, D-SUB High Density Solder pin, angled, .220" 5.6 mm - Socket connector 15 pos. 62 pos. 26 pos. 78 pos. 44 pos. PCB layout Kat1kGVA (View: component side) 2| 16 I P67 D-SUB C o n n e c t o r s PCB layout, D-SUB High Density Solder pin, angled, .220" 5.6 mm - Plug connector 15 pos. 62 pos. 26 pos. 78 pos. 44 pos. PCB layout Kat1kGWA (View: component side) 2| 17