D 9 S M 9 B O6 ST A 9 3 X0
2|2
IP67 D-SUB Connectors
Part Number Creator
Product Line
6 = Shell brass tin plated with die-cast frame
4* = Shell brass tin plated with plastic frame or without frame
8* = Shell stainless steel with or without die-cast frame
9* = Shell stainless steel with plastic frame
* on request
Variations
STD = D-SUBMINIATURE, Standard
HDD = D-SUBMINIATURE, High Density
Position for STD Position for HDD
09 = 9 pos. 15 = 15 pos.
15 = 15 pos. 26 = 26 pos.
25 = 25 pos. 44 = 44 pos.
37 = 37 pos. 62 = 62 pos.
50 = 50 pos. 78 = 78 pos.
Contact type
P = Plug connector
S = Socket connector
A = Adapter
Quality class for contacts
A = Quality class 3 = 50 mating cycles
B = Quality class 2 = 200 mating cycles
C = Quality class 1 = 500 mating cycles
OX = Standard
E2 = Threaded rear spacer with PCB clip, PCB 1,60 mm
S1 = Metal bracket, M3 threaded insert
S2 = Metal bracket, 4-40 UNC threaded insert
S3 = Metal bracket, M3 threaded insert and PCB clip
S4 = Metal bracket, 4-40 UNC threaded insert and PCB clip
R1 = Metal bracket, M3 threaded insert
R2 = Metal bracket, 4-40 UNC threaded insert
R3 = Metal bracket, M3 threaded insert and PCB clip
R4 = Metal bracket, 4-40 UNC threaded insert and PCB clip
Mounting style
A1 = Riveted for wire assembly shell without sealing frame
B2 = M3 threaded insert
B3 = 4-40 UNC threaded insert
B4 = M3 front spacer
B5 = 4-40 UNC front spacer
B7 = 4-40 UNC front spacer and rear mounting stud
B8 = M3 threaded lock
B9 = 4-40 UNC front spacer
E1 = M3 threaded rear spacer with PCB clip .063" 1.60 mm
Termination
M = Solder cup
R = Solder pin, straight
T = Solder pin, angled, .189" 4.80 mm
U = Solder pin, angled, .276“ 7.00 mm
Z = Solder pin, angled, .465“ 11.8 mm
Y = Solder pin, angled, .220“ 5.60 mm (high density design only)
A = Adapter
Capacitance
99 = Without filter for STD and HDD
2|3
IP67 D-SUB Connectors
Technical Data
Technical alterations are subject to change without notice.
Insulator
Contacts
Contact plating
Shell
Test voltage U eff NN
Working voltage
Current rating
Contact resistance
Insulation resistance
Clearance and creepage distance
Operating temperature
Mating and unmating forces
Quality class
Materials
Polyester GF UL94 V-0
CU alloy
Gold plated over nickel
Brass tin plated (Standard)
Stainless steel on request
1000 V
125 V ≈ 60 V ≈
depending on isolation coordination (refer to DIN VDE 0110 IEC 664-1)
7.5 A (UL) 5 A (CSA,VDE) 3 A (UL,VDE) 2.5 A (CSA)
max. 10 mΩ prior to stressing, ∆ R max. 10 mΩ after stressing
per DIN 41652, Part 2
≥ 5 G
Ω
contact – contact ≥ .004" 1.0 mm ≥ .024“ 0.6 mm
contact – earth ≥ .047“ 1.2 mm
– 25 °C to + 105 °C
9 pos. ≤ 30 N 15 pos. ≤ 50 N
15 pos. ≤ 50 N 26 pos. ≤ 84 N
25 pos. ≤ 83 N 44 pos. ≤ 120 N
37 pos. ≤ 123 N 62 pos. ≤ 70 N
50 pos. ≤ 167 N 78 pos. ≤ 200 N
A = Quality class 3 = 50 mating cycles
B = Quality class 2 = 200 mating cycles
C = Quality class 1 = 500 mating cycles
D-Subminiature, Standard
9, 15, 25, 37 and 50 position D-Subminiature, High Density
15, 26, 44, 62 and 78 position
Mechanical and electrical characteristics
2|4
IP67 D-SUB Connectors
IP-Code figure definitions
Explanation to spray water protected (IP) systems and their environment.
This system, described in IEC 60529, was developed to represent standard values for respective protection:
a) Contact with, and ingress of, fixed foreign objects
b) The ingress of liquids to which the inside is to be exposed.
The first digit describes the level of protection for life, contacting objects and the intrusion of foreign bodies. The second digit describes the level of protection against
the ingress of liquids. The larger the first and second digits are, the greater afforded protection is, e.g. IP55 must also meet the requirements of all lower protection
levels, such as IP22, IP23, IP34 and IP54.
1. Code figure Definition Remark
0 Not protected
1 Protected against access to hazardous parts by the back of the hand.
Protected against fixed foreign objects Ø ≥ 1.969” 50 mm.
2 Protected against access to hazardous parts with a finger.
Protected against fixed foreign objects Ø ≥ .492” 12.5 mm.
3 Protected against access to hazardous parts with a tool.
Protected against fixed foreign objects Ø ≥ .098” 2.5 mm.
4 Protected against access to hazardous parts with a wire.
Protected against fixed foreign objects Ø ≥ .039” 1 mm.
5 Protected against access to hazardous parts with a wire. Ingress of dust is not completely blocked. But dust
Dust protected. may not penetrate to the extent that satisfactory
operation of the device or safety is impaired.
6 Protected against access to hazardous parts with a wire.
Dustproof. No ingress of dust.
0 Not protected
1 Protected against dropper.
2 Protected against dropper when the shell is tipped as much as 15°.
3 Protected against spray water Up to 60° of either side of the vertical, such spray
water shall have no harmful effects.
4 Protected against splash water On the shell from all directions, no harmful effects
shall be incurred.
5 Protected against jets of water.
6 Protected against strong jets of water.
7 Protected against the effects of temporary submersion in water. Water may not ingress in a volume that would cause
harmful effects when the shell is submerged in water
for 30 min at a depth of 1 m.
8 Protected against the effects of continuous submersion in water. Water may not ingress in a volume that would
cause harmful effects when the shell is continuously
submerged in water under conditions agreed between
manufacturer and user.
However, these conditions must be more stringent
than those described under code figure 7.
9k Protected against water from high-pressure or steam cleaning.
2. Code figure Definition Remark
2|5
IP67 D-SUB Connectors
Mating conditions
Rigid mount tolerance guideFloat mount tolerance guide
Rear panel mounting IP67 D-SUB Connectors
Rigid mount vertical to tolerance guide
Front panel mounting IP67 D-SUB Connectors
Panel cut-out
Shell size A ±0.1 B ±0.1 C ±0.1 D ±0.1 E ±0.1
1 20.50 20.90 25.00 11.40 13.00
228.80 29.20 33.30 11.40 13.00
3 42.50 42.90 47.04 11.40 13.00
4 59.10 59.40 63.50 11.40 13.00
5 56.30 57.00 61.10 14.10 15.80
2|6
Panel Mounting
Front panel mounting
Rear panel mounting
The hex bolts illustrated here (4-40 UNC or M3 threads) are included in the delivery complement of every connector with a
sealing frame. The length of this spacer has been selected to accommodate a panel thickness of .063”/1.6 mm such that it does
not extend beyond the plug-in height. Furthermore, the hex bolts outside threads are shorter than standard hex bolts. Material:
stainless steel.
IP67 D-SUB Connectors
2|24
IP67 D-SUB Connectors
Solder profile
Connector Type Preheating Solder terminal dipping parameters
max. Temperature Duration max. Solder bath Temperature max. Terminal Immersion Time
Filter D-SUB 100°C 30s 260°C 5s
Combo D-SUB Filter 120°C 120s 260°C 5s
Filter D-SUB Water Resistant 100°C 30s 240°C 5s
Combo D-SUB Water Resistant 120°C 120s 240°C 5s
D-SUB Water Resistant 120°C 120s 240°C 5s
D-SUB Solid Body Type Water Resistant 150°C 180s 265°C 8s
RJ45 Modular Jack Filtered 150°C 180s 265°C 8s
Filter Plates 150°C 180s 265°C 8s
Recommended wave-solder parameters for CONEC connectors.
