IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH(R) PRODUCTS 2.5V / 3.3V 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH FEATURES: IDTQS3VH251 DESCRIPTION: * N channel FET switches with no parasitic diode to VCC - Isolation under power-off conditions - No DC path to VCC or GND - 5V tolerant in OFF and ON state * 5V tolerant I/Os typical * Low RON - 4 * Flat RON characteristics over operating range * Rail-to-rail switching 0 - 5V * Bidirectional dataflow with near-zero delay: no added ground bounce * Excellent RON matching between channels * VCC operation: 2.3V to 3.6V * High bandwidth - up to 500MHz * LVTTL-compatible control Inputs * Undershoot Clamp Diodes on all switch and control Inputs * Low Demux capacitance, 4pF typical * Available in QSOP and TSSOP packages The QS3VH251 HotSwitch Quad 2:1 multiplexer/demultiplexer is a high bandwidth bus switch. The QS3VH251 has very low ON resistance, resulting in under 250ps propagation delay through the switch. The Select (Sx) input controls the data flow. The multiplexers/demultiplexers are enabled when the Enable (E) input is low. In the ON state, the switches can pass signals up to 5V. In the OFF state, the switches offer very high impedence at the terminals. The combination of near-zero propagation delay, high OFF impedance, and over-voltage tolerance makes the QS3VH251 ideal for high performance comminucation applications. The QS3VH251 is characterized for operation from -40C to +85C. APPLICATIONS: * * * * * Hot-swapping Multiplexing/demultiplexing Low distortion analog switch Replaces mechanical relay ATM 25/155 switching FUNCTIONAL BLOCK DIAGRAM S0 S1 S2 E I0 I1 I2 I3 Y I4 I5 I6 I7 The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE AUGUST 2002 1 c 2002 Integrated Device Technology, Inc. DSC-5944/7 IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION I3 Symbol 1 16 2 I2 INDUSTRIAL TEMPERATURE RANGE 15 VCC I4 I1 3 14 I5 I0 4 13 I6 Y 5 12 I7 NC 6 11 S0 E GND 7 8 10 9 S1 S2 Max Unit SupplyVoltage to Ground -0.5 to +4.6 V DC Switch Voltage VS -0.5 to +5.5 V VTERM(3) DC Input Voltage VIN -0.5 to +5.5 V VAC AC Input Voltage (pulse width 20ns) -3 V IOUT DC Output Current (max. sink current/pin) 120 mA TSTG Storage Temperature -65 to +150 C VTERM(2) VTERM(3) Description NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VCC terminals. 3. All terminals except VCC . CAPACITANCE (TA = +25C, F = 1MHz, VIN = 0V, VOUT = 0V) Parameter(1) Symbol Typ. CIN Control Inputs CI/O Quickswitch Channels (Switch OFF) QSOP/ TSSOP TOP VIEW CI/O Quickswitch Channels (Switch ON) Demux 25 28 Mux 20 28 PIN DESCRIPTION S1 S0 Y Function H X X X Z Disable L L L L I0 S2 - S0 = 0 L L L H I1 S2 - S0 = 1 E I Enable Input Y O Data Outputs H L I2 S2 - S0 = 2 L L H H I3 S2 - S0 = 3 L H L L I4 S2 - S0 = 4 L H L H I5 S2 - S0 = 5 L H H L I6 S2 - S0 = 6 L H H H I7 S2 - S0 = 7 NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level X = Don't Care Z = High-Impedence 2 pF pF 19 S2 L 5 6 20 E L 3 Mux FUNCTION TABLE(1) Pin Names I/O Description I0 - I7 I Data Inputs S0 - S 2 I Select Input Unit 4 Demux NOTE: 1. This parameter is guaranteed but not production tested. Select Max. pF IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 3.3V 0.3V Symbol VIH VIL Parameter Test Conditions Input HIGH Voltage Input LOW Voltage IIN Input Leakage Current (Control Inputs) Min. Typ.(1) Max. Unit Guaranteed Logic HIGH VCC = 2.3V to 2.7V 1.7 -- -- for Control Inputs VCC = 2.7V to 3.6V 2 -- -- V Guaranteed Logic LOW VCC = 2.3V to 2.7V -- -- 0.7 for Control Inputs VCC = 2.7V to 3.6V -- -- 0.8 0V VIN VCC -- -- 1 A V IOZ Off-State Current (Hi-Z) 0V VOUT 5V, Switches OFF -- -- 1 A I OFF Data Input/Output Power Off Leakage VIN or VOUT 0V to 5V, VCC = 0V -- -- 1 A VCC = 2.3V VIN = 0V ION = 30mA -- 6 8 RON Switch ON Resistance Typical at VCC = 2.5V VIN = 1.7V ION = 15mA -- 7 9 VCC = 3V VIN = 0V ION = 30mA -- 4 6 VIN = 2.4V ION = 15mA -- 5 8 NOTE: 1. Typical values are at VCC = 3.3V and TA = 25C. TYPICAL ON RESISTANCE vs VIN AT VCC = 3.3V 16 14 R ON 12 (ohms) 10 8 6 4 2 0 0.0 0.5 1.0 1.5 2.0 2.5 V IN (Volts) 3 3.0 3.5 4.0 4.5 5.0 IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Test Conditions(1) Parameter Min. Typ. Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or VCC, f = 0 -- 1 4 mA ICC Power Supply Current (2,3) per Input HIGH VCC = Max., VIN = 3V, f = 0 per Control Input -- -- 30 A ICCD Dynamic Power Supply Current VCC = 3.3V, A and B Pins Open, Control Inputs (4) See Typical ICCD vs Enable Frequency graph below Toggling @ 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Per input driven at the specified level. Mux/demux pins do not contribute to Icc. 3. This parameter is guaranteed but not tested. 4. This parameter represents the current required to switch internal capacitance at the specified frequency. The mux/demux inputs do not contribute to the Dynamic Power Supply Current. This parameter is guaranteed but not production tested. TYPICAL ICCD vs ENABLE FREQUENCY CURVE AT VCC = 3.3V 6 ICCD (mA) 4 2 0 0 2 4 6 8 10 12 ENABLE FREQUENCY (MHz) 4 14 16 18 20 IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40C to +85C VCC = 2.5 0.2V (1) Symbol tPLH tPHL tSEL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ tPLZ Parameter Data Propagation Delay(2,3) Y to Ix or Ix to Y Select Time Sx to Y Enable Time S to Ix Disable Time S to Ix Enable Time E to Y or Ix Disable Time E to Y or Ix fEorSx Operating Frequency - Enable(2,5) Min. (4) VCC = 3.3 0.3V (1) Max. 0.2 Min. (4) Max. 0.2 Unit ns 1.5 9 1.5 8 ns 1.5 9 1.5 9 ns 1.5 8 1.5 8 ns 1.5 9 1.5 8 ns 1.5 8 1.5 8 ns 10 20 MHz NOTES: 1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS. 2. This parameter is guaranteed but not production tested. 3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.2ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4. Minimums are guaranteed but not production tested. 5. Maximum toggle frequency for Sx or E control input (pass voltage > VCC, VIN = 5V, RLOAD 1M, no CLOAD). 5 IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH SOME APPLICATIONS FOR HOTSWITCH PRODUCTS Rail-to-Rail Switching Multiplexing/Demultiplexing Hot-Swapping 6 INDUSTRIAL TEMPERATURE RANGE IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS TEST CONDITIONS Symbol VCC = 3.3V 0.3V VCC = 2.5V 0.2V Unit VLOAD 6 2 x Vcc V VIH 3 Vcc V (1) (2) VT 1.5 VCC/2 V VLZ 300 150 mV VHZ 300 150 mV CL 50 30 pF SAM E PHASE INPUT TRANSITION tPLH t PHL t PLH tPHL OUTPUT V IH VT 0V V OH VT V OL V IH VT 0V O PPOSITE PHASE INPUT TRANSITION Propagation Delay V LOAD V CC 500 (1, 2) Pulse Generator V IN CONTRO L INPUT G ND t PZL V OUT D.U.T. RT DISABLE ENABLE Open OUTPUT SW ITCH NORMALLY CLO SED LOW tPZ H OUTPUT SW ITCH NORMALLY OPEN HIGH 500 CL tPLZ V IH VT 0V V LOAD/2 V LO A D /2 VT VOL VOL t PHZ + V LZ VT VOH V O H -V H Z 0V 0V Test Circuits for All Outputs NOTE: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. Enable and Disable Times DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate 10MHz; tF 2.5ns; tR 2.5ns. 2. Pulse Generator for All Pulses: Rate 10MHz; tF 2ns; tR 2ns. SWITCH POSITION Test Switch tPLZ/tPZL VLOAD tPHZ/tPZH GND tPD Open 7 IDTQS3VH251 2.5V / 3.3V QUAD 8:1 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION IDTQS XXXXX Device Type XX Package Q QG PA Quarter Size Outline Package QSOP - Green Thin Shrink Small Outline Package 3VH251 2.5V / 3.3V 8:1 Mux/Demux High Bandwidth Bus Switch DATA SHEET DOCUMENT HISTORY 8/6/2002 Updated according to PCN Logic-0206-11 CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com 8 for Tech Support: logichelp@idt.com (408) 654-6459