220 EDLC ENYCAPTM www.vishay.com Vishay BCcomponents Electrical Double Layer Energy Storage Capacitors Power and Energy Versions FEATURES * Polarized energy storage capacitor with high capacity and energy density * Energy version with high stability available * Rated voltage: 2.7 V * Available in through-hole (radial) version * Useful life: 1000 h at 85 C * Rapid charge and discharge * Maintenance-free, no service necessary * AEC-Q200 qualified * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS * * * * * Image is not to scale QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (O D x L in mm) Rated capacitance range, CR Rated voltage, UR (65 C / 85 C) Category temperature range Endurance test at 85 C Useful life at 85 C Useful life at 20 C Shelf life at 20 C Cycle life VALUE 10 x 20; 10 x 25; 10 x 30; 12.5 x 20; 12.5 x 25; 12.5 x 30; 12.5 x 40; 16 x 20; 18 x 20; 16 x 25, 18 x 25; 16 x 31; 18 x 31, 18 x 35, 18 x 40 5 F to 60 F 2.7 V / 2.3 V -40 C to +85 C 1000 h 1000 h > 10 years 2 years > 500 000 cycles Power backup Burst power support Storage device for energy harvesting Micro UPS power source Energy recovery MARKING The capacitors are marked (where possible) with the following information: * Rated capacitance (in F) * Rated voltage (in V) * Date code, in accordance with IEC 60062 * Code indicating factory of origin * Logo of manufacturer * Negative terminal identification * Series number (220) PACKAGING Supplied loose in box, taped ammo, or in ESD trays. SELECTION CHART FOR CR, UR, AND RELEVANT NOMINAL CASE SIZES (O D x L in mm) CR (F) UR (V) = 2.7 V 5 7 8 10 12 15 20 22 25 30 10 x 20 10 x 25 12.5 x 20 10 x 30 12.5 x 25 12.5 x 30; 16 x 20 16 x 20; 16 x 25; 18 x 20 12.5 x 40 16 x 25; 18 x 20; 18 x 25 16 x 31; 18 x 25 35 16 x 31, 18 x 31 (1) 40 45, 50 55, 60 18 x 31 (1) 18 x 35 18 x 40 Note (1) Preferred case size Revision: 19-Nov-2019 Document Number: 28421 1 For technical questions, contact: energystorage@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 220 EDLC ENYCAPTM www.vishay.com Vishay BCcomponents DIMENSIONS in millimeters AND AVAILABLE FORMS L Od OD F 5 min. 15 min. Fig. 1 - Form CA / TRAY: Long leads Fig. 2 - Form TFA: Taped in box (ammopack) Table 1 DIMENSIONS in millimeters, MASS, AND PACKAGING QUANTITIES NOMINAL CASE SIZE ODxL PACKAGING QUANTITIES CASE CODE Od O Dmax. Lmax. F MASS (g) FORM CA FORM TFA FORM TRAY 10 x 20 16 0.6 10.5 22 5.0 0.5 2.2 500 800 - 10 x 25 16L 0.6 10.5 27 5.0 0.5 3.0 500 800 - 10 x 30 16LL 0.8 10.5 32 5.0 0.5 3.5 500 800 - 12.5 x 20 17 0.6 13.0 22 5.0 0.5 4.0 500 500 - 12.5 x 25 18 0.6 13.0 27 5.0 0.5 5.0 250 500 - 12.5 x 30 18L 0.8 13.0 33.5 5.0 0.5 5.5 250 500 - 12.5 x 40 18LL 0.8 13.0 42.5 5.0 0.5 7.0 250 - - 16 x 20 19a 0.8 16.5 22 7.5 0.5 6.0 250 250 200 16 x 25 19 0.8 16.5 27 7.5 0.5 8.0 250 250 200 18 x 20 1820 0.8 18.5 22 7.5 0.5 7.0 100 250 200 18 x 25 1825 0.8 18.5 27 7.5 0.5 10.0 100 250 200 16 x 31 20 0.8 16.5 33.5 7.5 0.5 9.0 100 250 200 18 x 31 1831 0.8 18.5 33.5 7.5 0.5 12.5 100 250 200 18 x 35 22 0.8 18.5 37.5 7.5 0.5 14.5 100 250 200 18 x 40 1840 0.8 18.5 42.5 7.5 0.5 16.5 100 - 150 ORDERING EXAMPLE ELECTRICAL DATA SYMBOL DESCRIPTION CR Rated capacitance, tolerance -20 % / +50 % IP Max. peak current IL Max. leakage current after 0.5 h / 72 h at UR Capacitor series 220 EDLC 40 F / 2.7 V Nominal case size: O 18 mm x 31 mm; Form tray Ordering code: MAL222091001E3 Note * Unless otherwise specified, all electrical values in Table 2 apply at Tamb = 20 C, P = 86 kPa to 106 kPa and RH = 45 % to 75 % Revision: 19-Nov-2019 Document Number: 28421 2 For technical questions, contact: energystorage@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 220 EDLC ENYCAPTM www.vishay.com Vishay BCcomponents Table 2 ELECTRICAL DATA AND ORDERING INFORMATION FOR ENERGY VERSION IL MAX. STORED IP NOMINAL MAX. MAX. PEAK LEAKAGE ENERGY UR UCT (1) MAX. (2) CASE ESRAC CURRENT CURRENT E AT UR US CR (V) (V) ESRDC (2) SIZE AFTER (V) 100 Hz INITIAL, (A) (Wh) INITIAL ODxL (< 1 s) (F) 1 kHz (mA) (A) (m) (mm) (m) 65 C 85 C SPECIFIC ENERGY Ed AT UR (Wh/kg) 65 C 85 C 0.5 h 72 h 65 C 85 C 65 C 85 C ORDERING CODE MAL2220....... FORM CA FORM TFA FORM TRAY 2.7 2.3 2.85 15 16 x 20 40 30 25 20 6 75 0.015 0.011 2.5 1.8 50003E3 30003E3 90003E3 2.7 2.3 2.85 20 16 x 25 38 28 25 20 6 75 0.020 0.015 2.5 1.8 50006E3 30006E3 90006E3 2.7 2.3 2.85 20 18 x 20 38 28 25 20 6 75 0.020 0.015 2.9 2.1 50004E3 30004E3 90004E3 2.7 2.3 2.85 25 18 x 25 36 26 25 20 11 115 0.025 0.018 2.5 1.8 50007E3 30007E3 90007E3 2.7 2.3 2.85 30 16 x 31 36 26 25 20 15 150 0.030 0.022 3.4 2.5 50002E3 30002E3 90002E3 2.7 2.3 2.85 35 18 x 31 35 25 25 20 15 150 0.035 0.029 3.5 2.6 50001E3 30001E3 90001E3 2.7 2.3 2.85 45 18 x 35 30 21 25 20 20 200 0.046 0.033 3.2 2.3 50008E3 30008E3 90008E3 2.7 2.3 2.85 55 18 x 40 25 18 25 20 25 250 0.056 0.040 3.4 2.5 50009E3 - 90009E3 Notes (1) U CT = rated voltage at upper category temperature (2) Rated capacitance C and ESR R DC Table 3 ELECTRICAL DATA AND ORDERING INFORMATION FOR POWER VERSION UR UCT (1) (V) (V) IL MAX. IP STORED NOMINAL MAX. MAX. PEAK LEAKAGE ENERGY MAX. (2) CASE ESRAC CURRENT CURRENT E AT UR US CR ESRDC (2) SIZE AFTER (V) 100 Hz INITIAL, (A) (Wh) INITIAL ODxL (< 1 s) (F) 1 kHz (mA) (A) (m) (mm) (m) 65 C 85 C SPECIFIC ENERGY Ed AT UR (Wh/kg) 65 C 85 C 0.5 h 72 h 65 C 85 C 65 C 85 C 2.7 2.3 2.85 5 2.7 2.3 2.85 2.7 2.3 2.85 2.7 2.3 2.7 2.7 ORDERING CODE MAL2220....... FORM CA FORM TFA FORM TRAY 10 x 20 35 28 12 10 2 25 0.005 0.004 2.3 1.8 51011E3 31011E3 - 7 10 x 25 31 24 12 10 3 35 0.007 0.005 2.3 1.7 51012E3 31012E3 - 8 12.5 x 20 28 21 15 12 4 40 0.008 0.006 2.0 1.5 51014E3 31014E3 - 2.85 10 10 x 30 27 20 15 12 4 45 0.009 0.007 2.6 2.0 51013E3 31013E3 - 2.3 2.85 12 12.5 x 25 26 19 17 14 5 55 0.011 0.008 2.2 1.6 51015E3 31015E3 - 2.3 2.85 15 12.5 x 30 23 16 20 17 6 70 0.015 0.011 2.7 2.0 51016E3 31016E3 - 2.7 2.3 2.85 20 16 x 20 24 18 25 20 8 75 0.020 0.015 3.4 2.3 51003E3 31003E3 91003E3 2.7 2.3 2.85 22 12.5 x 40 18 11 25 20 9 75 0.021 0.015 3.0 2.1 51017E3 2.7 2.3 2.85 25 16 x 25 22 16 25 20 8 75 0.025 0.018 3.2 2.3 51006E3 31006E3 91006E3 2.7 2.3 2.85 25 18 x 20 20 15 25 20 8 75 0.025 0.018 3.6 2.6 51004E3 31004E3 91004E3 2.7 2.3 2.85 30 18 x 25 19 13 30 25 12 140 0.030 0.022 3.0 2.2 51007E3 31007E3 91007E3 2.7 2.3 2.85 35 16 x 31 20 14 30 25 15 200 0.035 0.026 3.9 2.9 51002E3 31002E3 91002E3 2.7 2.3 2.85 40 18 x 31 18 12 35 30 20 200 0.041 0.029 3.3 2.3 51001E3 31001E3 91001E3 2.7 2.3 2.85 50 18 x 35 15 10 35 30 25 250 0.051 0.037 3.5 2.6 51008E3 31008E3 91008E3 2.7 2.3 2.85 60 18 x 40 13 9 35 30 30 300 0.061 0.044 3.7 2.7 51009E3 - - - 91009E3 Notes (1) U CT = rated voltage at upper category temperature (2) Rated capacitance C and ESR R DC Revision: 19-Nov-2019 Document Number: 28421 3 For technical questions, contact: energystorage@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 220 EDLC ENYCAPTM www.vishay.com Vishay BCcomponents TEST PROCEDURES AND REQUIREMENTS (1) PROCEDURE (quick reference) NAME OF TEST Capacitance CR and ESRDC Measured by DC discharging method as described in "Measuring of Characteristics". (2) Maximum peak current Non-repetitive current for maximum 1 s at specified operating temperature. Maximum operating voltage (refer to derating table) must not be exceeded. Usually to be tested with constant current discharge from UR to 0.5 x UR. Maximum current should not be used in normal operation and is only provided as reference value. Leakage current IL Measured at UR. Capacitor is charged to the rated voltage at 20 C. Leakage current is the current at specified time that is required to keep the capacitor charged at the rated voltage. After loading the capacitor of specified time at maximum category temperature Tmax. = 85 C and derated permissible maximum operating voltage U = 2.3 V, following parameters are valid within a timeframe of 1000 h: Endurance Capacitance Within 30 % of minimum initial specified value ESR Less than 3 x initial specified value Leakage Within specified value After loading the capacitor of specified time at maximum category temperature Tmax. = 85 C and derated permissible maximum operating voltage U = 2.3 V, following parameters are valid within a timeframe of 1000 h: Useful life Capacitance Within 30 % of minimum initial specified value ESR Less than 3 x initial specified value Leakage Within specified value After loading the capacitor of specified time at maximum category temperature Tmax. = 85 C and without charge and under 40 % RH, following parameters are valid within a timeframe of 1000 h: Storage at upper category temperature Shelf life Capacitance Within 30 % of minimum initial specified value ESR Less than 3 x initial specified value Leakage Within specified value Stored uncharged at 20 C. Parameter within initial specification Cycles at 20 C between rated voltage and half of rated voltage UR with constant current and 1 s rest between charge and discharge: > 500 000 cycles Cycle life Capacitance Within 30 % of minimum initial specified value ESR Less than 3 x initial specified value E [Wh] = 1/2 x C x (UR)2 x 1/3600 Stored energy E, specific energy Ed and Ev Ed [Wh/kg] = 1/2 x C x (UR)2 x 1/3600 x 1/mass Ev [Wh/L] = 1/2 x C x (UR)2 x 1/3600 x 1/volume Soldering Hand or wave soldering allowed. For details refer to soldering requirements for radial aluminum electrolytic capacitors in supplementary document. Cleaning For printed circuit board cleaning apply non-aggressive cleaning agents only. For details refer to cleaning requirements for aluminum electrolytic capacitors in supplementary document. Environmental conditions Do not expose capacitors to * temperatures outside specified range * high humidity atmospheres * corrosive atmospheres, e.g. halogenides, sulphurous or nitrous gases, acid or alkaline solutions, etc. * environments containing oil and grease Notes * General remark: temperatures to be measured at capacitor case (1) Conditions: electrical measurements at 20 C, unless otherwise specified (2) Rated capacitance C and ESR R DC Revision: 19-Nov-2019 Document Number: 28421 4 For technical questions, contact: energystorage@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 220 EDLC ENYCAPTM www.vishay.com Vishay BCcomponents MEASURING OF CHARACTERISTICS CAPACITANCE (C) EQUIVALENT SERIES RESISTANCE (ESRDC) Capacitance shall be measured by constant current discharge method. - Constant current charge to UR - Constant current charge with 10 mA/F to UR - Constant current discharge to 0.1 V - Constant voltage charge at UR U 3 V ESR DC = --------------------ID A - Constant current discharge with 10 mA/F to 0.1 V UR - Constant voltage charge at UR ESRDC UR ID U3 U1 Equivalent series resistance, in Voltage drop at internal resistance, in V Absolute value of discharge current, in A U2 30 min t1 t2 (s) Fig. 3 - Voltage Diagram for Capacitance Measurement Capacitance value CR is given by discharge current ID, time t and rated voltage UR, according to the following equation: ID A x t2 s - t1 s C R F = --------------------------------------------------------------U1 V - U2 V CR UR U1 U2 U3 t1 t2 ID Rated capacitance, in F Rated voltage, in V Starting voltage, 0.8 x UR in V Ending voltage, 0.4 x UR in V Voltage drop at internal resistance, in V Time from start of discharge until voltage U1 is reached, in s Time from start of discharge until voltage U2 is reached, in s Absolute value of discharge current, in A Statements about product lifetime are based on calculations and internal testing. They should only be interpreted as estimations. Also due to external factors, the lifetime in the field application may deviate from the calculated lifetime. In general, nothing stated herein shall be construed as a guarantee of durability. Revision: 19-Nov-2019 Document Number: 28421 5 For technical questions, contact: energystorage@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000