POWER
LPT100-M Series
130 Watts
Total Power: 130 Watts
Input Voltage: 90 - 264 Vac
# of Outputs: Triple
SPECIAL FEATURES
Medical and ITE safeties
Active power factor correction
2” x 4” footprint
Less than 1U high
EN61000-3-2 compliant
Remote sense
Power fail
Adjustable main output
Built-in Class B EMI lter
Overvoltage protection
Overload protection
Thermal overload protection
LPX100 enclosure kit available
RoHS compliant
SAFETY
TUV 60950, 60601-1
UL 60950, 60601-1
CSA 60950, 60601-1
NEMKO 60950, 60601-1
AUSTEL 60950, 60601-1
CB Certicate & report
CE Mark (LVD)
Electrical Specications
Input
Input ra nge 90 - 264 Vac; 127 - 300 Vdc
Frequency 47 - 63 Hz
Inrush current 50 A max., cold start @ 25 °C
Efficiency 82% typical at full load
EMI/RFI FCC Class B conducted; CISPR22 Class B conducted;
EN55022 Class B conducted; VDE0878PT3 Class B conducted
Safety ground
leakage current
275 µA @ 50/60 Hz, 264 Vac input
Output
Maximum power 130 W with 200 LFM forced air
Adjustment range
All outputs adjustable: -20%, +10%, except for +24V output on
LPT104-M which will be -10%, +20% and 3.3 V output on the LPT101-
M +10%, -15%
Hold-up time 10 ms @ 130 W load, 120 Vac input
Overload protection Short circuit protection on all outputs. Case overload
protected @ 110 - 160% above rating for V1 & V2, 150 - 250% for V3
Overvoltage protection 15 - 35% above nominal output
Logical Control
Power failure Active LowTTL logic signal goes high 100 - 500 msec after main output;
it goes low at least 6 msec before loss of regulation
Remote sense Compensates for 0.5 V lead drop min. Will operate without remote
sense connected. Reverse connection protected.
Data Sheet
LPT100-M Series Data Sheet
Environmental Specications
Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50 °C to 70 °C. -20 °C start up
Storage temperature -40 °C to +85 °C
Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10% - 95%
Vibration IEC68-2-6 to the levels of IEC721-3-2
MTBF calculated 583,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore
Mechanical Drawing
max lead
protrusion
min stand-o
height
1
8
"
4 places mounting hole
max screw head
diameter 0.22"[5.6]
PIN 1 (LIVE)
PIN 3 (NEUTRAL)
SK1
"
SK3
DETAIL A
1
4(-) REMOTE SENSE
SK2
GND
ADJUST POT'S
OUTPUT VOLTAGE SK3
SEE DETAIL A
POWER FAIL
COMMON
(+) REMOTE SENSE
0.1 "
[2,5]
1.29 "
[32,7]
0.197
[5]
1.72 "
[43,8]
3.72 "
[94,6]
4
[101,6]
0.16
[4]
2
[50,8]
LPT100-M Series Data Sheet
Ordering Information
Model Number Output Voltage Minimum Load Maximum Load with
30CFM Forced Air Peak Load Regulation2Ripple
P/P (PARD)3
LPT101-M
+3.3 V 0 A 18 A 20 A ±2% 50 mV
+5 V 0 A 9 A 10 A ±5% 50 mV
+12 V 0 A 2.3 A 2.3 A ±5% 120 mV
LPT102-M
+5 V 0 A 18 A 20 A ±2% 50 mV
+12 V 0 A 9 A 10 A ±5% 120 mV
-12 V 0 A 2 A 2 A ±5% 120 mV
LPT103-M
+5 V 0 A 18 A 20 A ±2% 50 mV
+15 V 0 A 7.2 A 8 A ±5% 150 mV
-15 V 0 A 1.5 A 2 A ±5% 150 mV
LPT104-M
+5 V 0 A 18 A 20 A ±2% 50 mV
+24 V 0 A 3 A 3.5 A ±7% 240 mV
+12 V 0 A 2.3 A 2.3 A ±5% 120 mV
1. Peak current lasting < 15 seconds with a maximum 10% duty cycle.
2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges.
4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated
as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and
System Integrators, including through Distribution Channels. It is not intended for sale to End Users.
LPT100-M Series Data Sheet
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. © 2018 Artesyn Embedded Technologies, Inc.
All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal.
www.artesyn.com
LPT100-M DS 16Jul2018
Pin Assignments
Connector LPT100-M
SK1 PIN 1 Live
PIN 3 Neutral
SK2 PIN 1 V1out
PIN 2 V1out
PIN 3 GND
PIN 4 GND
PIN 5 GND
PIN 6 GND
PIN 7 V2out
PIN 8 V3out
SK3 PIN 1 Power Fail
PIN 2 GND
PIN 3 + Remote Sense
PIN 4 - Remote Sense
Mating Connectors
AC Input (SK1)
Molex 09-50-3031
PINS: 08-52-0072
AC Ground Molex 01-90020001
DC Output (SK2) JST VHR-8N
PINS: SVH-21T-P1.1
Remote Sense
(SK3)
JST PHR-4; PINS: SPH-002T-PO.5S
OR
LANDWIN 2001S0400; PINS: 2005T
Artesyn Embedded Technologies Connector Kit #70-841-026,
includes all of the above
Notes:
1. Specifications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±.02”.
3. All mounting holes should be grounded for EMI purpose
4. Mounting M1 is safety ground connection
5. This power supply requires mounting on metal standoffs 0.20” (5 m) in
height.
6. For DC input an external DC safety rated fuse must be used.
7. Warranty: 2 year
8. Weight: 0.44 lb. / 0.20 kg
