CC1110Fx / CC1111Fx Low-Power SoC (System-on-Chip) with MCU, Memory, Sub-1 GHz RF Transceiver, and USB Controller Applications Low-power SoC wireless applications operating in the 315/433/868/915 MHz ISM/SRD bands Wireless alarm and security systems Industrial monitoring and control Wireless sensor networks AMR - Automatic Meter Reading Home and building automation Low power telemetry CC1111Fx: USB dongles Product Description The CC1110Fx/CC1111Fx is a true low-power sub1 GHz system-on-chip (SoC) designed for lowpower wireless applications. The CC1110Fx/CC1111Fx combines the excellent performance of the state-of-the-art RF transceiver CC1101 with an industry-standard enhanced 8051 MCU, up to 32 kB of in-system programmable flash memory and up to 4 kB of RAM, and many other powerful features. The small 6x6 mm package makes it very suited for applications with size limitations. VDD (2.0 - 3.6 V) DIGITAL DCOUPL ANALOG MIXED RESET_N XOSC_Q2 XOSC_Q1 P2_4 P2_3 P2_2 P2_1 P2_0 P1_7 P1_6 P1_5 P1_4 P1_3 P1_2 The CC1110Fx/CC1111Fx is highly suited for systems where very low power consumption is required. This is ensured by several advanced low-power operating modes. The CC1111Fx adds a full-speed USB 2.0 interface to the feature set of the CC1110Fx. Interfacing to a PC using the USB interface is quick and easy, and the high data rate (12 Mbps) of the USB interface avoids the bottlenecks of RS-232 or low-speed USB interfaces. P1_1 P1_0 P0_7 P0_6 P0_5 P0_4 P0_3 P0_2 P0_1 P0_0 RF_P DP RF_N DM Key Features Radio o o o o o o o o High-performance RF transceiver based on the market-leading CC1101 Excellent receiver selectivity and blocking performance High sensitivity (-110 dBm at 1.2 kBaud) Programmable data rate up to 500 kBaud Programmable output power up to 10 dBm for all supported frequencies Frequency range: 300 - 348 MHz, 391 - 464 MHz and 782 - 928 MHz Digital RSSI / LQI support MCU, Memory, and Peripherals o o o o o o o o o o o o o Low Power o o o Low current consumption (RX: 16.2 mA @ 1.2 kBaud, TX: 15.2 mA @ -6 dBm output power) 0.3 A in PM3 (the operating mode with the lowest power consumption) 0.5 A in PM2 (operating mode with the second lowest power consumption, timer or external interrupt wakeup) High performance and low power 8051 microcontroller core. Powerful DMA functionality 8/16/32 KB in-system programmable flash, and 1/2/4 KB RAM Full-Speed USB Controller with 1 KB FIFO (CC1111Fx ) 128-bit AES security coprocessor 7 - 12 bit ADC with up to eight inputs 2 I S interface Two USARTs 16-bit timer with DSM mode Three 8-bit timers Hardware debug support 21 (CC1110Fx ) or 19 (CC1111Fx ) GPIO pins SW compatible with CC2510Fx/CC2511Fx General SWRS033G o o Wide supply voltage range (2.0V - 3.6V) RoHS compliant 6x6 mm QFN 36 package Page 1 of 244 CC1110Fx / CC1111Fx Table of Contents ABBREVIATION.................................................................................................................................................. 4 1 REGISTER CONVENTIONS .................................................................................................................. 5 2 KEY FEATURES (IN MORE DETAILS) .............................................................................................. 5 2.1 HIGH-PERFORMANCE AND LOW-POWER 8051-COMPATIBLE MICROCONTROLLER....................................... 5 2.2 8/16/32 KB NON-VOLATILE PROGRAM MEMORY AND 1/2/4 KB DATA MEMORY ........................................ 5 2.3 FULL-SPEED USB CONTROLLER (CC1111FX )................................................................................................. 5 2.4 I2S INTERFACE .............................................................................................................................................. 5 2.5 HARDWARE AES ENCRYPTION/DECRYPTION ............................................................................................... 6 2.6 PERIPHERAL FEATURES ................................................................................................................................ 6 2.7 LOW POWER ................................................................................................................................................. 6 2.8 SUB-1 GHZ RADIO WITH BASEBAND MODEM .............................................................................................. 6 3 ABSOLUTE MAXIMUM RATINGS ...................................................................................................... 7 4 OPERATING CONDITIONS .................................................................................................................. 8 4.1 CC1110FX OPERATING CONDITIONS ............................................................................................................... 8 4.2 CC1111FX OPERATING CONDITIONS ............................................................................................................... 8 5 GENERAL CHARACTERISTICS.......................................................................................................... 8 6 ELECTRICAL SPECIFICATIONS ........................................................................................................ 9 6.1 CURRENT CONSUMPTION ............................................................................................................................. 9 6.2 RF RECEIVE SECTION ................................................................................................................................. 13 6.3 RF TRANSMIT SECTION .............................................................................................................................. 17 6.4 CRYSTAL OSCILLATORS ............................................................................................................................. 19 6.5 32.768 KHZ CRYSTAL OSCILLATOR ........................................................................................................... 20 6.6 LOW POWER RC OSCILLATOR .................................................................................................................... 20 6.7 HIGH SPEED RC OSCILLATOR .................................................................................................................... 21 6.8 FREQUENCY SYNTHESIZER CHARACTERISTICS ........................................................................................... 21 6.9 ANALOG TEMPERATURE SENSOR ............................................................................................................... 22 6.10 7 - 12 BIT ADC ........................................................................................................................................... 23 6.11 CONTROL AC CHARACTERISTICS ............................................................................................................... 25 6.12 SPI AC CHARACTERISTICS ......................................................................................................................... 26 6.13 DEBUG INTERFACE AC CHARACTERISTICS ................................................................................................ 27 6.14 PORT OUTPUTS AC CHARACTERISTICS ...................................................................................................... 27 6.15 TIMER INPUTS AC CHARACTERISTICS ........................................................................................................ 28 6.16 DC CHARACTERISTICS ............................................................................................................................... 28 7 PIN AND I/O PORT CONFIGURATION ............................................................................................ 29 8 CIRCUIT DESCRIPTION ..................................................................................................................... 33 8.1 CPU AND PERIPHERALS ............................................................................................................................. 34 8.2 RADIO ........................................................................................................................................................ 36 9 APPLICATION CIRCUIT ..................................................................................................................... 36 9.1 BIAS RESISTOR ........................................................................................................................................... 36 9.2 BALUN AND RF MATCHING ........................................................................................................................ 36 9.3 CRYSTAL .................................................................................................................................................... 36 9.4 REFERENCE SIGNAL ................................................................................................................................... 37 9.5 USB (CC1111FX) .......................................................................................................................................... 37 9.6 POWER SUPPLY DECOUPLING ..................................................................................................................... 37 9.7 PCB LAYOUT RECOMMENDATIONS ............................................................................................................ 41 10 8051 CPU.................................................................................................................................................. 41 10.1 8051 INTRODUCTION .................................................................................................................................. 41 10.2 MEMORY .................................................................................................................................................... 42 10.3 CPU REGISTERS ......................................................................................................................................... 54 10.4 INSTRUCTION SET SUMMARY ..................................................................................................................... 56 10.5 INTERRUPTS................................................................................................................................................ 60 11 DEBUG INTERFACE............................................................................................................................. 70 11.1 DEBUG MODE ............................................................................................................................................. 70 11.2 DEBUG COMMUNICATION........................................................................................................................... 70 11.3 DEBUG LOCK BIT ....................................................................................................................................... 71 SWRS033G Page 2 of 244 CC1110Fx / CC1111Fx 11.4 12 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8 12.9 12.10 12.11 12.12 12.13 12.14 12.15 12.16 13 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 13.11 13.12 13.13 13.14 13.15 13.16 13.17 13.18 13.19 14 14.1 15 16 17 17.1 17.2 17.3 17.4 18 19 20 20.1 20.2 21 22 DEBUG COMMANDS.................................................................................................................................... 72 PERIPHERALS....................................................................................................................................... 76 POWER MANAGEMENT AND CLOCKS.......................................................................................................... 76 RESET ......................................................................................................................................................... 83 FLASH CONTROLLER .................................................................................................................................. 84 I/O PORTS................................................................................................................................................... 90 DMA CONTROLLER ................................................................................................................................. 101 16-BIT TIMER, TIMER 1............................................................................................................................. 112 MAC TIMER (TIMER 2) ............................................................................................................................ 124 SLEEP TIMER ............................................................................................................................................ 126 8-BIT TIMERS, TIMER 3 AND TIMER 4 ....................................................................................................... 129 ADC......................................................................................................................................................... 140 RANDOM NUMBER GENERATOR ............................................................................................................... 146 AES COPROCESSOR .................................................................................................................................. 147 WATCHDOG TIMER ................................................................................................................................... 150 USART .................................................................................................................................................... 152 I2S ............................................................................................................................................................ 161 USB CONTROLLER ................................................................................................................................... 169 RADIO.................................................................................................................................................... 185 COMMAND STROBES ................................................................................................................................ 185 RADIO REGISTERS .................................................................................................................................... 187 INTERRUPTS.............................................................................................................................................. 187 TX/RX DATA TRANSFER ......................................................................................................................... 189 DATA RATE PROGRAMMING ..................................................................................................................... 190 RECEIVER CHANNEL FILTER BANDWIDTH ................................................................................................ 190 DEMODULATOR, SYMBOL SYNCHRONIZER, AND DATA DECISION ............................................................ 191 PACKET HANDLING HARDWARE SUPPORT ............................................................................................... 192 MODULATION FORMATS........................................................................................................................... 195 RECEIVED SIGNAL QUALIFIERS AND LINK QUALITY INFORMATION ......................................................... 196 FORWARD ERROR CORRECTION WITH INTERLEAVING .............................................................................. 200 RADIO CONTROL ...................................................................................................................................... 201 FREQUENCY PROGRAMMING .................................................................................................................... 204 VCO......................................................................................................................................................... 205 OUTPUT POWER PROGRAMMING .............................................................................................................. 205 SHAPING AND PA RAMPING ..................................................................................................................... 206 SELECTIVITY ............................................................................................................................................ 207 SYSTEM CONSIDERATIONS AND GUIDELINES ........................................................................................... 208 RADIO REGISTERS .................................................................................................................................... 211 VOLTAGE REGULATORS ................................................................................................................ 229 VOLTAGE REGULATOR POWER-ON ........................................................................................................... 229 RADIO TEST OUTPUT SIGNALS..................................................................................................... 229 REGISTER OVERVIEW ..................................................................................................................... 231 PACKAGE DESCRIPTION (QFN 36)................................................................................................ 235 RECOMMENDED PCB LAYOUT FOR PACKAGE (QFN 36).......................................................................... 236 SOLDERING INFORMATION ........................................................................................................................ 236 TRAY SPECIFICATION ............................................................................................................................... 236 CARRIER TAPE AND REEL SPECIFICATION ................................................................................................ 237 ORDERING INFORMATION............................................................................................................. 237 REFERENCES ...................................................................................................................................... 238 GENERAL INFORMATION............................................................................................................... 239 DOCUMENT HISTORY ............................................................................................................................... 239 PRODUCT STATUS DEFINITIONS ............................................................................................................... 242 ADDRESS INFORMATION ................................................................................................................ 243 TI WORLDWIDE TECHNICAL SUPPORT..................................................................................... 243 SWRS033G Page 3 of 244 CC1110Fx / CC1111Fx Abbreviation Delta-Sigma LFSR Linear Feedback Shift Register ADC Analog to Digital Converter LNA Low-Noise Amplifier AES Advanced Encryption Standard LO Local Oscillator AGC Automatic Gain Control LQI Link Quality Indication ARIB Association of Radio Industries and Businesses LSB Least Significant Bit / Byte MAC Medium Access Control ASK Amplitude Shift Keying MCU Microcontroller Unit BCD Binary Coded Decimal MISO Master In Slave Out BER Bit Error Rate MOSI Master Out Slave In BOD Brown Out Detector MSB Most Significant Bit / Byte CBC Cipher Block Chaining NA Not Applicable CBC-MAC Cipher Block Chaining Message Authentication Code OFB Output Feedback (encryption) OOK On-Off Keying PA Power Amplifier PCB Printed Circuit Board PER Packet Error Rate PLL Phase Locked Loop PM{0 - 3} Power Mode 0 -3 PMC Power Management Controller POR Power On Reset PQI Preamble Quality Indicator PWM Pulse Width Modulator QLP Quad Leadless Package RAM Random Access Memory RCOSC RC Oscillator RF Radio Frequency RoHS Restriction on Hazardous Substances RSSI Receive Signal Strength Indicator RX Receive SCK Serial Clock SFD Start of Frame Delimiter Federal Communications Commission SFR Special Function Register FIFO First In First Out SINAD Signal-to-noise and distortion ratio GPIO General Purpose Input / Output SPI Serial Peripheral Interface HSSD High Speed Serial Debug SRAM Static Random Access Memory HW Hardware SW Software I/O Input / Output T/R Transmit / Receive I/Q In-phase / Quadrature-phase TX Transmit Inter-IC Sound UART Universal Asynchronous Receiver/Transmitter IF Intermediate Frequency USART IOC I/O Controller Universal Synchronous/Asynchronous Receiver/Transmitter ISM Industrial, Scientific and Medical USB Universal Serial Bus VCO Voltage Controlled Oscillator VGA Variable Gain Amplifier WDT Watchdog Timer XOSC Crystal Oscillator CCA Clear Channel Assessment CCM Counter mode + CBC-MAC CFB Cipher Feedback CFR Code of Federal Regulations CMOS Complementary Metal Oxide Semiconductor CPU CRC Central Processing Unit Cyclic Redundancy Check CTR Counter mode (encryption) DAC Digital to Analog Converter DMA Direct Memory Access DSM Delta-Sigma Modulator ECB Electronic Code Book EM Evaluation Module ENOB Effective Number of Bits EP{0 - 5} USB Endpoints 0 - 5 ESD ESR ETSI FCC 2 IS Electro Static Discharge Equivalent Series Resistance European Telecommunications Standard Institute ISR Interrupt Service Routine IV Initialization Vector JEDEC Joint Electron Device Engineering Council KB Kilo Bytes (1024 bytes) kbps kilo bits per second SWRS033G Page 4 of 244 CC1110Fx / CC1111Fx 1 Register Conventions Each SFR is described in a separate table. The table heading is given in the following format: REGISTER NAME (SFR Address) - Register Description. Each RF register is described in a separate table. The table heading is given in the following format: XDATA Address: REGISTER NAME - Register Description All register descriptions include a symbol denoted R/W describing the accessibility of each bit in the register. The register values are always given in binary notation unless prefixed by `0x', which indicates hexadecimal notation. Symbol Access Mode R/W Read/write R Read only R0 Read as 0 R1 Read as 1 W Write only W0 Write as 0 W1 Write as 1 H0 Hardware clear H1 Hardware set Table 1: Register Bit Conventions 2 Key Features (in more details) 2.1 High-Performance and Low-Power 8051-Compatible Microcontroller 2.3 5 bi-directional endpoints in addition to control endpoint 0 Optimized 8051 core which typically gives 8x the performance of a standard 8051 Full-Speed, 12 Mbps transfer rate Support for Bulk, Interrupt, Isochronous endpoints Two data pointers In-circuit interactive debugging is supported by the IAR Embedded Workbench through a simple two-wire serial interface and 1024 bytes of dedicated endpoint FIFO memory 8 - 512 byte data packet size supported SW compatible with CC2510Fx/CC2511Fx 2.2 Full-Speed USB Controller (CC1111Fx ) Configurable FIFO size for IN and OUT direction of endpoint 8/16/32 KB Non-volatile Program Memory and 1/2/4 kB Data Memory 2.4 2 I S Interface 8, 16, or 32 KB of non-volatile flash memory, in-system programmable through a simple two-wire interface or by the 8051 core Industry standard I S interface transfer of digital audio data Minimum flash memory 1000 write/erase cycles Mono and stereo support endurance: Programmable read and write lock of portions of flash memory for software security 2 for Full duplex Configurable sample rate and sample size Support for -law compression and expansion 1, 2, or 4 kB of internal SRAM SWRS033G Page 5 of 244 CC1110Fx / CC1111Fx 2.5 Typically used to connect to external DAC or ADC The high speed crystal oscillator must be used when the radio is active. Hardware AES Encryption/Decryption Clock source for ultra-low power operation can be either a low-power RC oscillator or an optional 32.768 kHz crystal oscillator 128-bit AES supported in hardware coprocessor 2.6 Very fast transition to active mode from power modes enables ultra low average power consumption in low duty-cycle systems Peripheral Features Powerful DMA Controller Power On Reset/Brown-Out Detection ADC with eight individual input channels, single-ended or differential (CC1111Fx has six channels) and configurable resolution 2.8 Programmable watchdog timer Five timers: one general 16-bit timer with DSM mode, two general 8-bit timers, one MAC timer, and one sleep timer Two programmable USARTs for master/slave SPI or UART operation 21 configurable general-purpose digital I/O-pins (CC1111Fx has 19) Random number generator Sub-1 GHz Radio with Baseband Modem Based on the industry leading CC1101 radio core Few external components: On-chip frequency synthesizer, no external filters or RF switch needed Flexible support for packet oriented systems: On-chip support for sync word detection, address check, flexible packet length, and automatic CRC handling Supports use of DMA for both RX and TX resulting in minimal CPU intervention even on high data rates 2.7 Low Power Four flexible power modes for reduced power consumption System can wake up on external interrupt or when the Sleep Timer expires 0.5 A current consumption in PM2, where external interrupts or the Sleep Timer can wake up the system 0.3 A current consumption in PM3, where external interrupts can wake up the system Low-power fully static CMOS design System clock source is either a high speed crystal oscillator (26 - 27 MHz for CC1110Fx and 48 MHz for CC1111Fx) or a high speed RC oscillator (13 - 13.5 MHz for CC1110Fx and 12 MHz for CC1111Fx). SWRS033G Programmable channel filter bandwidth 2-FSK, GFSK, MSK, ASK, and OOK modulation formats supported Optional automatic whitening and dewhitening of data Programmable indicator Carrier Sense (CS) Programmable Preamble Quality Indicator (PQI) for detecting preambles and improved protection against sync word detection in random noise Support for automatic Clear Channel Assessment (CCA) before transmitting (for listen-before-talk systems) Support for per-package Link Quality Indication (LQI) Page 6 of 244 CC1110Fx / CC1111Fx 3 Absolute Maximum Ratings Under no circumstances must the absolute maximum ratings given in Table 2 be violated. Stress exceeding one or more of the limiting values may cause permanent damage to the device. Parameter Min Max Units Supply voltage (VDD) -0.3 3.9 V Voltage on any digital pin -0.3 VDD + 0.3, max 3.9 V Voltage on the pins RF_P, RF_N and DCOUPL -0.3 2.0 V Voltage ramp-up rate 120 kV/s Input RF level 10 dBm 150 C Device not programmed Solder reflow temperature 260 C According to IPC/JEDEC J-STD-020D ESD CC1110Fx 1000 V According to JEDEC STD 22, method A114, Human Body Model (HBM) ESD CC1110Fx 750 V According to JEDEC STD 22, C101C, Charged Device Model (CDM) ESD CC1111x 750 V According to JEDEC STD 22, method A114, Human Body Model (HBM) ESD CC1111x 750 V According to JEDEC STD 22, C101C, Charged Device Model (CDM) Storage temperature range -50 Condition All supply pins must have the same voltage Table 2: Absolute Maximum Ratings Caution! ESD sensitive device. Precaution should be used when handling the device in order to prevent permanent damage. SWRS033G Page 7 of 244 CC1110Fx / CC1111Fx 4 Operating Conditions 4.1 CC1110Fx Operating Conditions The operating conditions for CC1110Fx are listed in Table 3 below. Parameter Min Max Unit Operating ambient temperature, TA -40 85 C Operating supply voltage (VDD) 2.0 3.6 V Condition All supply pins must have the same voltage Table 3: Operating Conditions for CC1110Fx 4.2 CC1111Fx Operating Conditions The operating conditions for CC1111Fx are listed in Table 4 below. Parameter Min Max Unit 0 85 C 3.0 3.6 V Operating ambient temperature, TA Operating supply voltage (VDD) Condition All supply pins must have the same voltage Table 4: Operating Conditions for CC1111Fx 5 General Characteristics TA = 25C, VDD = 3.0 V if nothing else stated Parameter Min Typ Max Unit 300 348 MHz 391 464 MHz 782 928 MHz 1.2 500 kBaud 1.2 250 kBaud 26 500 kBaud Condition/Note Radio part Frequency range Data rate 2-FSK (500 kBaud only characterized @ 915 MHz on CC1110Fx) GFSK, OOK, and ASK (Shaped) MSK (also known as differential offset QPSK) 500 kBaud only characterized @ 915 MHz Optional Manchester encoding (the data rate in kbps will be half the baud rate) Wake-Up Timing PM1 Active Mode 4 s Digital regulator on. HS RCOSC and high speed crystal oscillator off. 32.768 kHz XOSC or low power RCOSC running. SLEEP.OSC_PD=1 and CLKCON.OSC=1 PM2/3 Active Mode 100 s Digital regulator off. HS RCOSC and high speed crystal oscillator off. 32.768 kHz XOSC or low power RCOSC running (PM2). No crystal oscillators or RC oscillators are running in PM3 SLEEP.OSC_PD=1 and CLKCON.OSC=1 Table 5: General Characteristics SWRS033G Page 8 of 244 CC1110Fx / CC1111Fx 6 Electrical Specifications 6.1 Current Consumption TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference design ([1]). Parameter Active mode, full speed (high speed crystal oscillator)1. Min Typ Max Unit Condition 5.0 mA System clock running at 26 MHz. 4.8 mA System clock running at 24 MHz. Digital regulator on. High speed crystal oscillator and low power RCOSC running. No peripherals running. Low CPU activity. Low CPU activity: No flash access (i.e. only cache hit), no RAM access Active mode, full speed (HS RCOSC)1. 2.5 mA System clock running at 13 MHz. Digital regulator on. HS RCOSC and low power RCOSC running. No peripherals running. Low CPU activity. Low CPU activity: No flash access (i.e. only cache hit), no RAM access Active mode with radio in RX, 315 MHz Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in RX mode (sensitivity optimized MDMCFG2.DEM_DCFILT_OFF=0) 19 mA 1.2 kBaud, input at sensitivity limit, system clock running at 26 MHz. 19.5 mA 1.2 kBaud, input at sensitivity limit, system clock running at 24 MHz 16.2 mA 1.2 kBaud, input at sensitivity limit, system clock running at 203 kHz. 19 mA 1.2 kBaud, input well above sensitivity limit, system clock running at 26 MHz 19.4 mA 1.2 kBaud, input well above sensitivity limit, system clock running at 24 MHz 19 mA 38.4 kBaud, input at sensitivity limit, system clock running at 26 MHz. 16.2 mA 38.4 kBaud, input at sensitivity limit, system clock running at 203 kHz. 19 mA 38.4 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 20 mA 250 kBaud, input at sensitivity limit, system clock running at 26 MHz 21 mA 250 kBaud, input at sensitivity limit, system clock running at 24 MHz. 17.2 mA 250 kBaud, input at sensitivity limit, system clock running at 1.625 MHz. 20 mA 20 mA 250 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 250 kBaud, input well above sensitivity limit, system clock running at 24 MHz. 1 Note: In order to reduce the current consumption in active mode, the clock speed can be reduced by setting CLKCON.CLKSPD000 (see section 12.1 for details).Figure 1 shows typical current consumption in active mode for different clock speeds SWRS033G Page 9 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in RX mode (sensitivity optimized MDMCFG2.DEM_DCFILT_OFF=0) Active mode with radio in RX, 433 MHz 19.8 mA 1.2 kBaud, input at sensitivity limit, system clock running at 26 MHz. 19.7 mA 1.2 kBaud, input at sensitivity limit, system clock running at 24 MHz. 17.1 mA 1.2 kBaud, input at sensitivity limit, system clock running at 203 kHz. 19.8 mA 1.2 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 19.7 mA 1.2 kBaud, input well above sensitivity limit, system clock running at 24 MHz. 19.8 mA 38.4 kBaud, input at sensitivity limit, system clock running at 26 MHz. 17.1 mA 38.4 kBaud, input at sensitivity limit, system clock running at 203 kHz 19.8 mA 38.4 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 20.5 mA 250 kBaud, input at sensitivity limit, system clock running at 26 MHz. 21.5 mA 250 kBaud, input at sensitivity limit, system clock running at 24 MHz. 18.1 mA 250 kBaud, input at sensitivity limit, system clock running at 1.625 MHz. 20.5 mA 250 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 20.2 mA 250 kBaud, input well above sensitivity limit, system clock running at 24 MHz See Figure 2 for typical variation over operating conditions Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in RX mode (sensitivity optimized MDMCFG2.DEM_DCFILT_OFF=0). 24 MHz system clock not measured Active mode with radio in RX, 868, 915 MHz 19.7 mA 1.2 kBaud, input at sensitivity limit, system clock running at 26 MHz. 17.0 mA 1.2 kBaud, input at sensitivity limit, system clock running at 203 kHz. 18.7 mA 1.2 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 19.7 mA 38.4 kBaud, input at sensitivity limit, system clock running at 26 MHz. 17.0 mA 38.4 kBaud, input at sensitivity limit, system clock running at 203 kHz. 18.7 mA 38.4 kBaud, input well above sensitivity limit, system clock running at 26 MHz. 20.4 mA 250 kBaud, input at sensitivity limit, system clock running at 26 MHz. 18.0 mA 250 kBaud, input at sensitivity limit, system clock running at 1.625 MHz. 19.1 mA 250 kBaud, input well above sensitivity limit, system clock running at 26 MHz. System clock running at 26 MHz or 24 MHz. Active mode with radio in TX, 315 MHz Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in TX mode 31.5 mA 10 dBm output power (PA_TABLE0=0xC2) 19 mA 0 dBm output power (PA_TABLE0=0x51) 18 mA -6 dBm output power (PA_TABLE0=0x2A) SWRS033G Page 10 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition System clock running at 26 MHz or 24 MHz. Active mode with radio in TX, 433 MHz Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in TX mode 33.5 mA 10 dBm output power (PA_TABLE0=0xC0) 20 mA 0 dBm output power (PA_TABLE0=0x60) 19 mA -6 dBm output power (PA_TABLE0=0x2A) System clock running at 26 MHz or 24 MHz. Active mode with radio in TX, 868, 915 MHz Digital regulator on. High speed crystal oscillator and low power RCOSC running. Radio in TX mode 36.2 mA 10 dBm output power (PA_TABLE0=0xC2). See Table 7 for typical variation over operating conditions 21 mA 0 dBm output power (PA_TABLE0=0x50) 20 mA -6 dBm output power (PA_TABLE0=0x2B) Power mode 0 4.3 mA Same as active mode, but the CPU is not running (see 12.1.2.2 for details). System clock at 26 MHz or 24 MHz Power mode 1 220 A Digital regulator on. HS RCOSC and high speed crystal oscillator off. 32.768 kHz XOSC or low power RCOSC running (see 12.1.2.3 for details) Power mode 2 0.5 A Digital regulator off. HS RCOSC and high speed crystal oscillator off. Low power RCOSC running (see 12.1.2.4 for details) Power mode 3 0.3 A Digital regulator off. No crystal oscillators or RC oscillators are running (see 12.1.2.5 for details) 1.0 Peripheral Current Consumption Add to the figures above if the peripheral unit is activated Timer 1 2.7 A/MHz When running Timer 2 1.3 A/MHz When running Timer 3 1.6 A/MHz When running Timer 4 2 A/MHz When running 1.2 mA ADC During conversion Table 6: Current Consumption SWRS033G Page 11 of 244 CC1110Fx / CC1111Fx Current Consumption Active Mode. No Peripherals Running. fxosc = 26 MHz 6,0 5,0 Current [mA] 4,0 HS XOSC 3,0 HS RCOSC 2,0 1,0 0,0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 Clock Speed [MHz] Measurements done for all valid CLKCON.CLKSPD settings (000 - 111 for HS XOSC, 001 - 111 for HS RCOSC) Figure 1: Current Consumption (Active Mode) vs. Clock Speed Typical Variation in RX Current Consumption over Temperature and Input Power Level Data Rate = 250 kBaud, Frequency Band = 433 MHz Current [mA] 25 Avg -40C 23 Avg 25C Avg 85C 21 19 -110 -100 -90 -80 -70 -60 -40 -50 -30 -20 -10 Input Power Level [dBm] Figure 2: Typical Variation in RX Current Consumption over Temperature and Input Power Level. Data Rate = 250 kBaud, Frequency Band = 433 MHz Supply Voltage, VDD = 2 V Supply Voltage, VDD = 3 V Supply Voltage, VDD = 3.6 V Temperature [C] -40 25 85 -40 25 85 -40 25 85 Current [mA] 37 36 35.4 37.2 36.2 35.6 37.5 36.4 35.8 Table 7: Typical Variation in TX Current Consumption over Temperature and Supply Voltage, @ 868 MHz and 10 dBm Output Power. SWRS033G Page 12 of 244 CC1110Fx / CC1111Fx 6.2 RF Receive Section TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference design ([1]) if nothing else is stated. Parameter Digital channel filter bandwidth Min Typ 58 Max Unit Condition/Note 812 kHz User programmable (see Section 13.6). The bandwidth limits are proportional to crystal frequency (given values assume a 26 MHz system clock). 315 MHz, 1.2 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 5.2 kHz deviation, 58 kHz digital channel filter bandwidth) Receiver sensitivity -110 dBm System clock running at 26 MHz -112 dBm System clock running at 24 MHz The RX current consumption can be reduced by approximately 2.0 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -107 dBm. 315 MHz, 38.4 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 20 kHz deviation, 100 kHz digital channel filter bandwidth) Receiver sensitivity -102 dBm System clock running at 26 MHz -103 dBm System clock running at 24 MHz The RX current consumption can be reduced by approximately 2.1 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -99 dBm. 315 MHz, 250 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (MDMCFG2.DEM_DCFILT_OFF=1 cannot be used for data rates > 100 kBaud) (GSK, 1% packet error rate, 20 bytes packet length, 127 kHz deviation, 540 kHz digital channel filter bandwidth) Receiver sensitivity -94 dBm System clock running at 26 MHz -94 dBm System clock running at 24 MHz 433 MHz, 1.2 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 5.2 kHz deviation, 58 kHz digital channel filter bandwidth) Receiver sensitivity -110 dBm System clock running at 26 MHz -110 dBm System clock running at 24 MHz The RX current consumption can be reduced by approximately 2.6 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -107 dBm. 433 MHz, 38.4 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 20 kHz deviation, 100 kHz digital channel filter bandwidth) Receiver sensitivity -102 dBm System clock running at 26 MHz -101 dBm System clock running at 24 MHz The RX current consumption can be reduced by approximately 2.7 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -99 dBm. Parameter Min Typ Max Unit Condition/Note 433 MHz, 250 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (MDMCFG2.DEM_DCFILT_OFF=1 cannot be used for data rates > 100 kBaud) (GSK, 1% packet error rate, 20 bytes packet length, 127 kHz deviation, 540 kHz digital channel filter bandwidth) Receiver sensitivity -95 dBm System clock running at 26 MHz -93 dBm System clock running at 24 MHz See Table 9 for typical variation over operating conditions SWRS033G Page 13 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition/Note 868 MHz, 1.2 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 5.2 kHz deviation, 58 kHz digital channel filter bandwidth) Receiver sensitivity -110 dBm System clock running at 26 MHz -110 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock The RX current consumption can be reduced by approximately 2.0 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -107 dBm. Saturation -14 dBm MCSM0.CLOSE_IN_RX=00 Adjacent channel rejection 38 dB Desired channel 3 dB above the sensitivity limit. 100 kHz channel spacing Alternate channel rejection 35 dB Desired channel 3 dB above the sensitivity limit. 100 kHz channel spacing See Figure 58 for plot of selectivity versus frequency offset Image channel rejection, 868 MHz 33 dB IF frequency 152 kHz Desired channel 3 dB above the sensitivity limit. 868 MHz, 38.4 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (GSK, 1% packet error rate, 20 bytes packet length, 20 kHz deviation, 100 kHz digital channel filter bandwidth) Receiver sensitivity -102 dBm System clock running at 26 MHz -101 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock The RX current consumption can be reduced by approximately 2.2 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -100 dBm. Saturation -14 dBm Adjacent channel rejection 19 dB Desired channel 3 dB above the sensitivity limit. 200 kHz channel spacing Alternate channel rejection 32 dB Desired channel 3 dB above the sensitivity limit. 200 kHz channel spacing MCSM0.CLOSE_IN_RX=00 See Figure 59 for plot of selectivity versus frequency offset Image channel rejection, 868 MHz 28 dB IF frequency 152 kHz Desired channel 3 dB above the sensitivity limit. SWRS033G Page 14 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition/Note 868 MHz, 250 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (MDMCFG2.DEM_DCFILT_OFF=1 cannot be used for data rates > 100 kBaud) (GSK, 1% packet error rate, 20 bytes packet length, 127 kHz deviation, 540 kHz digital channel filter bandwidth) Receiver sensitivity -94 dBm System clock running at 26 MHz -91 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock MCSM0.CLOSE_IN_RX=00 Saturation -16 dBm Adjacent channel rejection 27 dB Desired channel 3 dB above the sensitivity limit. 750 kHz channel spacing Alternate channel rejection 36 dB Desired channel 3 dB above the sensitivity limit. 750 kHz channel spacing Image channel rejection, 868 MHz 17 dB See Figure 60 for plot of selectivity versus frequency offset IF frequency 304 kHz Desired channel 3 dB above the sensitivity limit. 915 MHz, 1.2 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (2-FSK, 5.2 kHz deviation, 1% packet error rate, 20 bytes packet length, 58 kHz digital channel filter bandwidth) Receiver sensitivity -108 dBm System clock running at 26 MHz -110 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock The RX current consumption can be reduced by approximately 2.0 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -107 dBm. 915 MHz, 38.4 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (2-FSK, 1% packet error rate, 20 bytes packet length, 100 kHz digital channel filter bandwidth) Receiver sensitivity -100 dBm System clock running at 26 MHz -100 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock The RX current consumption can be reduced by approximately 2.1 mA by setting MDMCFG2.DEM_DCFILT_OFF=1. The typical sensitivity is then -99 dBm. 915 MHz, 250 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (MDMCFG2.DEM_DCFILT_OFF=1 cannot be used for data rates > 100 kBaud) (MSK, 1% packet error rate, 20 bytes packet length, 540 kHz digital channel filter bandwidth) Receiver sensitivity -93 dBm System clock running at 26 MHz -91 dBm Tested conducted on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock 915 MHz, 500 kBaud data rate, sensitivity optimized, MDMCFG2.DEM_DCFILT_OFF=0 (MDMCFG2.DEM_DCFILT_OFF=1 cannot be used for data rates > 100 kBaud) (MSK, 1% packet error rate, 20 bytes packet length, 812 kHz digital channel filter bandwidth) Receiver sensitivity -86 dBm System clock running at 26 MHz. Not tested on [4] CC1111 USB-Dongle Reference Design, 24 MHz clock SWRS033G Page 15 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition/Note Blocking Blocking at 2 MHz offset, 1.2 kBaud, 868 MHz -45 dBm Desired channel 3 dB above the sensitivity limit. Blocking at 2 MHz offset, 250 kBaud, 868 MHz -50 dBm Desired channel 3 dB above the sensitivity limit Blocking at 10 MHz offset, 1.2 kBaud, 868 MHz -33 dBm Desired channel 3 dB above the sensitivity limit. Blocking at 10 MHz offset, 250 kBaud, 868 MHz -40 dBm Desired channel 3 dB above the sensitivity limit. General Conducted measurement in a 50 single ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66. Numbers are from CC1101 (same radio on CC1110 and CC1111) Typical radiated spurious emission is -49 dB measured at the VCO frequency. Spurious emissions 25 MHz 1 GHz -68 -57 dBm Maximum figure is the ETSI EN 300 220 limit Above 1 GHz -66 -47 dBm Maximum figure is the ETSI EN 300 220 limit Table 8: RF Receive Section Supply Voltage, VDD = 2 V Supply Voltage, VDD = 3 V Supply Voltage, VDD = 3.6 V Temperature [C] -40 25 85 -40 25 85 -40 25 85 Sensitivity [dBm] -96.4 -94.9 -92.6 -96.1 -95.0 -92.2 -96.1 -94.5 -92.2 Table 9: Typical Variation in Sensitivity over Temperature and Supply Voltage @ 433 MHz and 250 kBaud Data Rate SWRS033G Page 16 of 244 CC1110Fx / CC1111Fx 6.3 RF Transmit Section TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]) if nothing else is stated. Parameter Min Typ Max Unit Differential load impedance 315 MHz 122 + j31 433 MHz 116 + j41 868/915 MHz 86.5 + j43 Output power, highest setting 10 dBm Condition/Note Differential impedance as seen from the RF-port (RF_P and RF_N) towards the antenna. Follow the CC1110EM reference designs ([1], [2] and [3]) available from the TI website. Output power is programmable, and full range is available in all frequency bands Output power may be restricted by regulatory limits. See AN050 [13]. Note that this application note is for CC1101 but the same limitations apply to CC1110Fx and CC1111Fx as well. For CC1111Fx see in addition DN016 [14] for information on antenna solution and additional regulatory restrictions See Figure 3 for typical variation over operating conditions Delivered to 50 single-ended load via CC1110EM reference design [3] RF matching network. Output power, lowest setting -30 dBm Output power is programmable and is available across the entire frequency band Delivered to 50 single-ended load via CC1110EM reference design [3] RF matching network. Harmonics, radiated nd 2 Harm, 433 MHz 3rd Harm, 433 MHz nd 2 Harm, 868 MHz 3rd Harm, 868 MHz -51 -42 dBm dBm -37 -43 dBm dBm Harmonics, radiated nd 2 Harm, 868 MHz 3rd Harm, 868 MHz -55 dBm -55 dBm Harmonics, conducted Measured on CC1110EM reference designs ([2] and [3]) with CW, 10 dBm output power The antennas used during the radiated measurements (SMAFF-433 from R.W. Badland and Nearson S331 868/915) play a part in attenuating the harmonics Measured on [4] CC1111 USB-Dongle Reference Design, with CW, 10 dBm output power. The chip antenna used during the radiated measurements play a part in attenuating the harmonics Measured on CC1110EM reference designs ([1], [2] and [3]) with CW, 10 dBm output power, TX frequency at 315.00 MHz, 433.00 MHz, 868.00 MHz, or 915.00 MHz 315 MHz < -35 < -52 dBm Frequencies below 960 MHz Frequencies above 960 MHz 433 MHz < -44 < -35 dBm Frequencies below 1 GHz Frequencies above 1 GHz 868 MHz < -35 dBm Frequencies above 1 GHz 915 MHz < -34 dBm Frequencies above 1 GHz SWRS033G Page 17 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Spurious emissions radiated, Harmonics not included Condition/Note Measured on CC1110EM reference designs ([1], [2] and [3]) with 10 dBm CW, TX frequency at 315.00 MHz, 433.00 MHz, 868.00 or 915.00 MH. For CC1111Fx see DN016 [14] Please refer to register TEST1 on Page 225 for required settings in RX and TX 315 MHz < -58 < -53 dBm Frequencies below 960 MHz Frequencies above 960 MHz 433 MHz < -50 < -54 < -56 dBm Frequencies below 1 GHz Frequencies above 1 GHz Frequencies within 47 - 74, 87.5 - 118, 174 - 230, 470 - 862 MHz 868 MHz < -56 < -54 < -56 dBm Frequencies below 1 GHz Frequencies above 1 GHz Frequencies within 47 - 74, 87.5 - 118, 174 - 230, 470 - 862 MHz. 915 MHz < -51 < -60 dBm Frequencies below 960 MHz Frequencies above 960 MHz Table 10: RF Transmit Section Typical Variation in Output Power (10dBm) over Frequency and Temperature Output Power [dBm] 12 11 10 Avg -40C 9 Avg 25C 8 Avg 85C 7 6 750 800 850 900 950 Frequency [MHz] Figure 3: Typical Variation in Output Power over Frequency and Temperature (10 dBm output power) SWRS033G Page 18 of 244 CC1110Fx / CC1111Fx 6.4 6.4.1 Crystal Oscillators CC1110Fx Crystal Oscillator TA = 25C, VDD = 3.0 V if nothing else is stated. Parameter Crystal frequency Min Typ Max Unit Condition/Note 26 26 27 MHz Referred to as fXOSC. ppm This is the total tolerance including a) initial tolerance, b) crystal loading, c) aging, and d) temperature dependence. Crystal frequency accuracy requirement 40 The acceptable crystal tolerance depends on RF frequency and channel spacing / bandwidth. C0 1 5 Load capacitance 10 13 ESR Start-up time 7 pF Simulated over operating conditions 20 pF Simulated over operating conditions 100 Simulated over operating conditions s fXOSC = 26 MHz 250 Note: A Ripple counter of 12 bit is included to ensure duty-cycle requirements. Start-up time includes ripple counter delay until SLEEP.XOSC_STB is asserted Power Down Guard Time 3 ms The crystal oscillator must be in power down for a guard time before it is used again. This requirement is valid for all modes of operation. The need for power down guard time can vary with crystal type and load. Minimum figure is valid for reference crystal NDK, AT-41CD2 and load capacitance according to Table 29. If power down guard time is violated, one of the consequences can be increased PER when using the radio immediately after the crystal oscillator has been reported stable. Table 11: CC1110Fx Crystal Oscillator Parameters 6.4.2 CC1111Fx Crystal Oscillator TA = 25C, VDD = 3.0 V if nothing else is stated. Parameter Min Crystal frequency Typ Max 48 Unit Condition/Note MHz Referred to as fXOSC. 48 MHz crystal gives a system clock of 24 MHz. Please note that there is restricted usage in the frequency bands 863 870 MHz (due to spurious emission). See DN016 Compact Antenna Solutions for 868/915 MHz [14] Crystal frequency accuracy requirement 40 ppm This is the total tolerance including a) initial tolerance, b) crystal loading, c) aging, and d) temperature dependence. The acceptable crystal tolerance depends on RF frequency and channel spacing / bandwidth. C0 Fundamental Load capacitance 0.85 1 1.15 pF Simulated over operating conditions. Variation given by reference crystal NX2520SA from NDK (fundamental). 15 16 17 pF Simulated over operating conditions 60 Simulated over operating conditions ESR Start-up time Fundamental Note: A Ripple counter of 14 bit is included to ensure duty-cycle requirements. Start-up time includes ripple counter delay until SLEEP.XOSC_STB is asserted 650 s Table 12: CC1111Fx Crystal Oscillator Parameters SWRS033G Page 19 of 244 CC1110Fx / CC1111Fx 6.5 32.768 kHz Crystal Oscillator TA = 25C, VDD = 3.0V if nothing else is stated. Parameter Min Crystal frequency Typ Max 32.768 Unit Condition/Note kHz C0 0.9 2.0 pF Simulated over operating conditions Load capacitance 12 16 pF Simulated over operating conditions ESR 40 130 k Simulated over operating conditions Start-up time 400 ms Value is simulated Table 13: 32.768 kHz Crystal Oscillator Parameters 6.6 Low Power RC Oscillator TA = 25C, VDD = 3.0 V if nothing else is stated. Parameter 2 Calibrated frequency Min Typ Max Unit Condition/Note 34.7 34.7 36.0 kHz CC1110Fx 32.0 32.0 32.0 CC1111Fx Calibrated low power RC oscillator frequency is fRef / 750 Frequency accuracy after calibration Temperature coefficient 1 % +0.5 %/C Frequency drift when temperature changes after calibration Supply voltage coefficient +3 %/V Frequency drift when supply voltage changes after calibration Initial calibration time 2 ms When the low power RC oscillator is enabled, calibration is continuously done in the background as long as the high speed crystal oscillator is running. Table 14: Low Power RC Oscillator Parameters fRef = fXOSC for CC1110Fx and fRef = fXOSC /2 for CC1111Fx For CC1110Fx Min figures are given using fXOSC = 26 MHz. Typ figures are given using fXOSC = 26 MHz, and Max figures are given using fXOSC = 27 MHz. For CC1111Fx, fXOSC = 48 MHz 2 SWRS033G Page 20 of 244 CC1110Fx / CC1111Fx 6.7 High Speed RC Oscillator TA = 25C, VDD = 3.0 V if nothing else is stated. Parameter 2 Calibrated frequency Min Typ Max Unit Condition/Note 12 13 13.5 MHz Calibrated HS RCOSC frequency is fXOSC / 2 15 Uncalibrated frequency accuracy % Calibrated frequency accuracy 1 % Start-up time 10 s -325 ppm/C Frequency drift when temperature changes after calibration 28 ppm/V Frequency drift when supply voltage changes after calibration Temperature coefficient Supply voltage coefficient Calibration time 65 s The HS RCOSC will be calibrated once when the high speed crystal oscillator is selected as system clock source (CLKCON.OSC is set to 0), and also when the system wakes up from PM{1 - 3} if CLKCON.OSC was set to 0 when entering PM{1 - 3}. See 12.1.5.1 for details). Table 15: High Speed RC Oscillator Parameters 6.8 Frequency Synthesizer Characteristics TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Typ Max Unit Programmed frequency resolution3 397 397 412 Hz 366 366 366 Condition/Note CC1110Fx CC1111Fx Frequency resolution = fRef/ 216 Synthesizer frequency tolerance 40 ppm Given by crystal used. Required accuracy (including temperature and aging) depends on frequency band and channel bandwidth / spacing. RF carrier phase noise -92 dBc/Hz @ 50 kHz offset from carrier RF carrier phase noise -93 dBc/Hz @ 100 kHz offset from carrier RF carrier phase noise -93 dBc/Hz @ 200 kHz offset from carrier RF carrier phase noise -98 dBc/Hz @ 500 kHz offset from carrier RF carrier phase noise -107 dBc/Hz @ 1 MHz offset from carrier RF carrier phase noise -113 dBc/Hz @ 2 MHz offset from carrier RF carrier phase noise -119 dBc/Hz @ 5 MHz offset from carrier RF carrier phase noise -129 dBc/Hz @ 10 MHz offset from carrier fRef = fXOSC for CC1110Fx and fRef = fXOSC /2 for CC1111Fx For CC1110Fx Min figures are given using fXOSC = 26 MHz. Typ figures are given using fXOSC = 26 MHz, and Max figures are given using fXOSC = 27 MHz. For CC1111Fx, fXOSC = 48 MHz 3 SWRS033G Page 21 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit PLL turn-on / hop time4 72.4 75.2 75.2 s 81.4 81.4 81.4 Condition/Note CC1110Fx CC1111Fx Time from leaving the IDLE state until arriving in the RX, FSTXON, or TX state, when not performing calibration. Crystal oscillator running. RX to TX switch 4 29.0 30.1 30.1 32.6 32.6 32.6 CC1110Fx s CC1111Fx Settling time for the 1IF frequency step from RX to TX TX to RX switch 4 30.0 31.1 31.1 33.6 33.6 33.6 CC1110Fx s CC1111Fx Settling time for the 1IF frequency step from TX to RX PLL calibration time 4 707 735 735 796 796 796 CC1110Fx s CC1111Fx Calibration can be initiated manually or automatically before entering or after leaving RX/TX. Note: This is the PLL calibration time given that TEST0=0x0B and FSCAL3.CHP_CURR_CAL_EN=10 (max calibration time). Please see DN110 [15] for more details Table 16: Frequency Synthesizer Parameters 6.9 Analog Temperature Sensor TA= 25C, VDD = 3.0V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Typ Max Unit Output voltage at -0C 0.660 V Output voltage at 0C 0.755 V Output voltage at 40C 0.859 V Output voltage at 80C 0.958 V Temperature coefficient Error in calculated temperature, calibrated 2.47 -2 * 0 mV/C 2 * C Condition/Note Fitted from -20C to 80C From -20C to 80C when using 2.47 mV/C, after 1-point calibration at room temperature * The indicated minimum and maximum error with 1-point calibration is based on measured values for typical process parameters Current consumption increase when enabled 0.3 mA Table 17: Analog Temperature Sensor Parameters fRef = fXOSC for CC1110Fx and fRef = fXOSC /2 for CC1111Fx For CC1110Fx Min figures are given using fXOSC = 27 MHz. Typ figures are given using fXOSC = 26 MHz, and Max figures are given using fXOSC = 26 MHz. For CC1111Fx, fXOSC = 48 MHz The system clock frequency is equal to fRef and the data rate is 250 kBaud. No PA ramping is used. See DN110 [15] for more details. 4 SWRS033G Page 22 of 244 CC1110Fx / CC1111Fx 6.10 7 - 12 bit ADC TA = 25C, VDD = 3.0 V if nothing else stated. The numbers given here are based on tests performed in accordance with IEEE Std 1241-2000 [8]. The ADC data are from CC2430 characterization. As the CC1110Fx/C1111Fx uses the same ADC, the numbers listed in Table 18 should be good indicators of the performance to be expected from CC1110Fx and CC1111Fx. Note that these numbers will apply for 24 MHz operated systems (CC1111Fx using a 48 MHz crystal). Performance will be slightly different for other crystal frequencies (e.g. 26 MHz and 27 MHz). Parameter Min Typ Max Unit Condition/Note Input voltage 0 VDD V VDD is the voltage on the AVDD pin (2.0 - 3.6 V) External reference voltage 0 VDD V VDD is the voltage on the AVDD pin (2.0 - 3.6 V) External reference voltage differential 0 VDD V VDD is the voltage on the AVDD pin (2.0 - 3.6 V) Simulated using 4 MHz clock speed (see Section 12.10.2.7) Input resistance, signal 197 k Full-Scale Signal5 2.97 V 5.7 bits ENOB 5 Single ended input ENOB 5 Useful Power Bandwidth 7-bits setting 7.5 9-bits setting 9.3 10-bits setting 10.8 12-bits setting 6.5 Differential input Peak-to-peak, defines 0 dBFS bits 7-bits setting 8.3 9-bits setting 10.0 10-bits setting 11.5 12-bits setting 0 - 20 kHz 7-bits setting, both single and differential -Single ended input -75.2 dB 12-bits setting, -6 dBFS -Differential input -86.6 5 THD Signal To Non-Harmonic Ratio -Single ended input 70.2 -Differential input Spurious Free Dynamic Range -Single ended input 12-bits setting, -6 dBFS 5 dB 79.3 12-bits setting 5 78.8 dB 12-bits setting, -6 dBFS -Differential input 88.9 CMRR, differential input <-84 dB 12- bit setting, 1 kHz Sine (0 dBFS), limited by ADC resolution Crosstalk, single ended input <-84 dB 12- bit setting, 1 kHz Sine (0 dBFS), limited by ADC resolution -3 mV Mid. Scale Gain error 0.68 % 5 0.05 LSB Offset DNL 12-bits setting, -6 dBFS 0.9 INL5 4.6 12-bits setting, mean 12-bits setting, max LSB 13.3 5 12-bits setting 12-bits setting, mean 12-bits setting, max Measured with 300 Hz Sine input and VDD as reference. SWRS033G Page 23 of 244 CC1110Fx / CC1111Fx Parameter Min Typ Max Unit Condition/Note SINAD5 35.4 dB 7-bits setting Single ended input 46.8 dB 9-bits setting (-THD+N) 57.5 10-bits setting 66.6 12-bits setting 5 SINAD 40.7 Differential input 51.6 9-bits setting (-THD+N) 61.8 10-bits setting 70.8 12-bits setting Conversion time Current consumption 20 dB s 7-bits setting 7-bits setting 36 9-bits setting 68 10-bits setting 132 12-bits setting 1.2 mA Table 18: 7 - 12 bit ADC Characteristics SWRS033G Page 24 of 244 CC1110Fx / CC1111Fx 6.11 Control AC Characteristics TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Typ Max Unit Condition/Note CC1110Fx System clock, fSYSCLK tSYSCLK= 1/ fSYSCLK 0.1875 26 27 MHz High speed crystal oscillator used as source (HS XOSC). 0.1875 13 13.5 MHz Calibrated HS RCOSC used as source. HS XOSC HS RCOSC Min: fXOSC = 24 MHz, CLKCON.CLKSPD = 111 111 Typ: fXOSC = 26 MHz, CLKCON.CLKSPD = 000 001 Max: fXOSC = 27 MHz, CLKCON.CLKSPD = 000 001 HS XOSC HS RCOSC Min: fXOSC = 48 MHz, CLKCON.CLKSPD = 111 111 Typ: fXOSC = 48 MHz, CLKCON.CLKSPD = 000 001 Max: fXOSC = 48 MHz, CLKCON.CLKSPD = 000 001 CC1111Fx RESET_N low width 0.1875 24 24 MHz High speed crystal oscillator used as source 0.1875 12 12 MHz HS RCOSC used as source 250 ns See item 1, Figure 4. This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Note: Shorter pulses may be recognized but will not lead to complete reset of all modules within the chip. Interrupt pulse width tSYSCLK See item 2, Figure 4. This is the shortest pulse that is guaranteed to be recognized as an interrupt request. In PM2/3 the internal synchronizers are bypassed so this requirement does not apply in PM2/3. Table 19: Control Inputs AC Characteristics Figure 4: Control Inputs AC Characteristics SWRS033G Page 25 of 244 CC1110Fx / CC1111Fx 6.11.1 Filtering of RESET_N pin The RESET_N pin is sensitive to noise and can cause unintended reset of the chip. For a long reset line add an external RC filter with values 1 nF and 2.7 k close to the RESET_N pin. When doing this, note that the RESET_N low width (the shortest pulse that is guaranteed to be recognized as a reset pin request) is longer than stated in Table 19. 6.12 SPI AC Characteristics TA = 25C, VDD = 3.0V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min SCK period SCK duty cycle Typ Max Unit Condition/Note See Section 12.14.3 ns Master. See item 1, Figure 5 50 % Master. SSN low to SCK 2tSYSCLK See item 5, Figure 5 SCK to SSN high 30 ns See item 6, Figure 5 MISO setup 10 ns Master. See item 2, Figure 5 MISO hold 10 ns Master. See item 3, Figure 5 ns Master. See item 4, Figure 5, load = 10 pF ns Slave. See item 1, Figure 5 % Slave. SCK to MOSI SCK period 25 100 SCK duty cycle 50 MOSI setup 10 ns Slave. See item 2, Figure 5 MOSI hold 10 ns Slave. See item 3, Figure 5 ns Slave. See item 4, Figure 5, load = 10 pF SCK to MISO 25 Table 20: SPI AC Characteristics Figure 5: SPI AC Characteristics SWRS033G Page 26 of 244 CC1110Fx / CC1111Fx 6.13 Debug Interface AC Characteristics TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Debug clock period 125 Typ Max Unit Condition/Note ns See item 1, Figure 6 Note: CLKCON.CLKSPD must be 000 or 001 when using the debug interface Debug data setup 5 Debug data hold 5 Clock to data delay 10 RESET_N inactive after P2_2 rising 10 ns See item 2, Figure 6 ns See item 3, Figure 6 ns See item 4, Figure 6, load = 10 pF ns See item 5, Figure 6 Table 21: Debug Interface AC Characteristics 1 DEBUG CLK P2_2 3 2 DEBUG DATA P2_1 4 DEBUG DATA P2_1 5 RESET_N Figure 6: Debug Interface AC Characteristics 6.14 Port Outputs AC Characteristics TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Typ Max Unit Condition/Note P0_[0:7], P1_[2:7], P2_[0:4] Port output rise time (IOCFG1.GDO_DS=0 / IOCFG1.GDO_DS=1) 3.15 / 1.34 ns Load = 10 pF Timing is with respect to 10% VDD and 90% VDD levels. Values are estimated P0_[0:7], P1_[2:7], P2_[0:4] Port output fall time (IOCFG1.GDO_DS=0 / IOCFG1.GDO_DS=1) 3.2 / 1.44 ns Load = 10 pF Timing is with respect to 90% VDD and 10% VDD. Values are estimated Table 22: Port Outputs AC Characteristics SWRS033G Page 27 of 244 CC1110Fx / CC1111Fx 6.15 Timer Inputs AC Characteristics TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Parameter Min Input capture pulse width Typ Max Unit tSYSCLK Condition/Note Synchronizers determine the shortest input pulse that can be recognized. The synchronizers operate from the current system clock rate (see Table 19) Table 23: Timer Inputs AC Characteristics 6.16 DC Characteristics The DC Characteristics of CC1110Fx/CC1111Fx are listed in Table 24 below. TA = 25C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1110EM reference designs ([1]). Digital Inputs/Outputs Min Typ Logic "0" input voltage Max Unit Condition 30 % Of VDD supply (2.0 - 3.6 V) % Of VDD supply (2.0 - 3.6 V) Logic "1" input voltage 70 Logic "0" input current per pin N/A 12 nA Input equals 0 V Logic "1" input current per pin N/A 12 nA Input equals VDD Total logic "0" input current all pins 70 nA Total logic "1" input current all pins 70 nA I/O pin pull-up and pull-down resistor 20 k Table 24: DC Characteristics SWRS033G Page 28 of 244 CC1110Fx / CC1111Fx 7 Pin and I/O Port Configuration GUARD AVDD_DREG DCOUPL RESET_N P1_7 P1_6 P1_5 P1_4 P1_3 The CC1110Fx pin-out is shown in Figure 7 and Table 25. See Section 12.4 for details on the I/O configuration. 36 35 34 33 32 31 30 29 28 P1_2 1 27 RBIAS DVDD 2 26 AVDD P1_1 3 25 AVDD P1_0 4 24 RF_N P0_0 5 P0_1 6 23 RF_P 22 AVDD P0_2 7 21 XOSC_Q1 P0_3 8 20 XOSC_Q2 P0_4 9 19 AVDD 10 11 12 13 14 15 16 17 18 P2_4/XOSC32_Q2 P2_3/XSOC32_Q1 P2_2 P2_1 P2_0 P0_7 P0_6 P0_5 DVDD AGND Exposed die attached pad Figure 7: CC1110Fx Pinout Top View Note: The exposed die attach pad must be connected to a solid ground plane as this is the ground connection for the chip. SWRS033G Page 29 of 244 CC1110Fx / CC1111Fx Pin Pin Name Pin Type Description - AGND Ground The exposed die attach pad must be connected to a solid ground plane 1 P1_2 D I/O Port 1.2 2 DVDD Power (Digital) 2.0 V - 3.6 V digital power supply for digital I/O 3 P1_1 D I/O Port 1.1 4 P1_0 D I/O Port 1.0 5 P0_0 D I/O Port 0.0 6 P0_1 D I/O Port 0.1 7 P0_2 D I/O Port 0.2 8 P0_3 D I/O Port 0.3 9 P0_4 D I/O Port 0.4 10 DVDD Power (Digital) 2.0 V - 3.6 V digital power supply for digital I/O 11 P0_5 D I/O Port 0.5 12 P0_6 D I/O Port 0.6 13 P0_7 D I/O Port 0.7 14 P2_0 D I/O Port 2.0 15 P2_1 D I/O Port 2.1 16 P2_2 D I/O Port 2.2 17 P2_3/XOSC32_Q1 D I/O Port 2.3/32.768 kHz crystal oscillator pin 1 18 P2_4/XOSC32_Q2 D I/O Port 2.4/32.768 kHz crystal oscillator pin 2 19 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 20 XOSC_Q2 Analog I/O Crystal oscillator pin 2 21 XOSC_Q1 Analog I/O Crystal oscillator pin 1, or external clock input 22 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 23 RF_P RF I/O Positive RF input signal to LNA in receive mode Positive RF output signal from PA in transmit mode 24 RF_N RF I/O Negative RF input signal to LNA in receive mode Negative RF output signal from PA in transmit mode 25 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 26 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 27 RBIAS Analog I/O External precision bias resistor for reference current 28 GUARD Power (Digital) Power supply connection for digital noise isolation 29 AVDD_DREG Power (Digital) 2.0 V - 3.6 V digital power supply for digital core voltage regulator 30 DCOUPL Power decoupling 1.8 V digital power supply decoupling 31 RESET_N DI Reset, active low 32 P1_7 D I/O Port 1.7 33 P1_6 D I/O Port 1.6 34 P1_5 D I/O Port 1.5 35 P1_4 D I/O Port 1.4 36 P1_3 D I/O Port 1.3 Table 25: CC1110Fx Pin-out Overview SWRS033G Page 30 of 244 CC1110Fx / CC1111Fx GUARD AVDD_DREG DCOUPL RESET_N P1_7 P1_6 P1_5 P1_4 P1_3 The CC1111Fx pin-out is shown in Figure 8 and Table 26. See Section 12.4 for details on the I/O configuration. 36 35 34 33 32 31 30 29 28 P1_2 1 27 R_BIAS DVDD 2 26 AVDD P1_1 3 25 AVDD P1_0 4 24 RF_N P0_0 5 P0_1 6 23 RF_P 22 AVDD P0_2 7 21 XOSC_Q1 P0_3 8 20 XOSC_Q2 P0_4 9 19 AVDD 10 11 12 13 14 15 16 17 18 P2_4/XOSC32_Q2 P2_3/XSOC32_Q1 P2_2 P2_1 P2_0 P0_5 DVDD DM DP AGND Exposed die attached pad Figure 8: CC1111Fx Pin-out Top View Note: The exposed die attach pad must be connected to a solid ground plane as this is the ground connection for the chip. SWRS033G Page 31 of 244 CC1110Fx / CC1111Fx Pin Pin Name Pin Type Description - AGND Ground The exposed die attach pad must be connected to a solid ground plane 1 P1_2 D I/O Port 1.2 2 DVDD Power (Digital) 2.0 V - 3.6 V digital power supply for digital I/O 3 P1_1 D I/O Port 1.1 4 P1_0 D I/O Port 1.0 5 P0_0 D I/O Port 0.0 6 P0_1 D I/O Port 0.1 7 P0_2 D I/O Port 0.2 8 P0_3 D I/O Port 0.3 9 P0_4 D I/O Port 0.4 10 DP USB I/O USB Differential Data Bus Plus 11 DM USB I/O USB Differential Data Bus Minus 12 DVDD Power (Digital) 2.0 V - 3.6 V digital power supply for digital I/O 13 P0_5 D I/O Port 0.5 14 P2_0 D I/O Port 2.0 15 P2_1 D I/O Port 2.1 16 P2_2 D I/O Port 2.2 17 P2_3/XOSC32_Q1 D I/O Port 2.3/32.768 kHz crystal oscillator pin 1 18 P2_4/XOSC32_Q2 D I/O Port 2.4/32.768 kHz crystal oscillator pin 2 19 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 20 XOSC_Q2 Analog I/O Crystal oscillator pin 2 21 XOSC_Q1 Analog I/O Crystal oscillator pin 1, or external clock input 22 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 23 RF_P RF I/O Positive RF input signal to LNA in receive mode Positive RF output signal from PA in transmit mode 24 RF_N RF I/O Negative RF input signal to LNA in receive mode Negative RF output signal from PA in transmit mode 25 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 26 AVDD Power (Analog) 2.0 V - 3.6 V analog power supply connection 27 RBIAS Analog I/O External precision bias resistor for reference current 28 GUARD Power (Digital) Power supply connection for digital noise isolation 29 AVDD_DREG Power (Digital) 2.0 V - 3.6 V digital power supply for digital core voltage regulator 30 DCOUPL Power decoupling 1.8 V digital power supply decoupling 31 RESET_N DI Reset, active low 32 P1_7 D I/O Port 1.7 33 P1_6 D I/O Port 1.6 34 P1_5 D I/O Port 1.5 35 P1_4 D I/O Port 1.4 36 P1_3 D I/O Port 1.3 Table 26: CC1111Fx Pin-out Overview SWRS033G Page 32 of 244 CC1110Fx / CC1111Fx 8 Circuit Description Figure 9:C C1110Fx/CC1111Fx Block Diagram A block diagram of CC1110Fx/CC1111Fx is shown in Figure 9. The modules can be divided into one out of three categories: CPU-related modules, radio-related modules, and modules related to power, test, and clock distribution. In the following sub-sections, a short description of each module that appears in Figure 9. SWRS033G Page 33 of 244 CC1110Fx / CC1111Fx 8.1 CPU and Peripherals 2 The 8051 CPU core is a single-cycle 8051compatible core. It has three different memory access buses (SFR, DATA and CODE/XDATA), a debug interface, and an extended interrupt unit servicing 18 interrupt sources. See Section 1 for details on the CPU. access to the radio registers and I S registers in the radio register bank even though these are indeed mapped into XDATA memory space. The 1/2/4 KB SRAM maps to the DATA memory space and part of the XDATA and CODE memory spaces. The memory is an ultra-low-power SRAM that retains its contents even when the digital part is powered off (PM2 and PM3). The memory crossbar/arbitrator is at the heart of the system as it connects the CPU and DMA controller with the physical memories and all peripherals through the SFR bus. The memory arbitrator has four memory access points, access at which can map to one of three physical memories on the CC2510Fx and one of four physical memories on the CC2511Fx: a 1/2/4 KB SRAM, 8/16/32 KB 2 flash memory, RF/I S registers, and USB registers (CC2511Fx). The memory arbitrator is responsible for performing arbitration and sequencing between simultaneous memory accesses to the same physical memory. The 8/16/32 KB flash block provides in-circuit programmable non-volatile program memory for the device and maps into the CODE and XDATA memory spaces. Table 27 shows the available devices in the CC1110/CC1111 family. The available devices differ only in flash memory size. Writing to the flash block is performed through a Flash Controller that allows page-wise (1024 byte) erasure and 2byte-wise reprogramming. See Section 12.3 for details. The SFR bus is drawn conceptually in the block diagram as a common bus that connects all hardware peripherals, except USB, to the memory arbitrator. The SFR bus also provides Device Flash [KB] CC1110F8 8 CC1111F8 8 CC1110F16 16 CC1111F16 16 CC1110F32 32 CC1111F32 32 Table 27: CC1110Fx/CC1111Fx Flash Memory Options A versatile five-channel DMA controller is available in the system. It accesses memory using a unified memory space and has therefore access to all physical memories. Each channel is configured (trigger event, priority, transfer mode, addressing mode, source and destination pointers, and transfer count) with DMA descriptors anywhere in memory. Many of the hardware peripherals rely on the DMA controller for efficient operation (AES core, Flash Controller, USARTs, Timers, and ADC interface) by performing data transfers between a single SFR address and flash/SRAM. See Section 12.5 for details. The interrupt controller services 18 interrupt sources, divided into six interrupt groups, each of which is associated with one out of four interrupt priorities. An interrupt request is serviced even if the device is in PM1, PM2, or PM3 by bringing the CC1110Fx/CC1111Fx back to active mode. The debug interface implements a proprietary two-wire serial interface that is used for incircuit debugging. Through this debug interface it is possible to perform an erasure of the entire flash memory, control which oscillators are enabled, stop and start execution of the user program, execute supplied instructions on the 8051 core, set code breakpoints, and single step through instructions in the code. Using these techniques it is possible to perform in-circuit debugging and external flash programming. See Section 11 for details. SWRS033G Page 34 of 244 CC1110Fx / CC1111Fx The I/O-controller is responsible for all general-purpose I/O pins. The CPU can configure whether peripheral modules control certain pins or if they are under software control. In the latter case, each pin can be configured as an input or output and it is also possible to configure the input mode to be pullup, pull-down, or tristate. Each peripheral that connects to the I/O-pins can choose between two different I/O pin locations to ensure flexibility in various applications. See Section 12.4 for details. The Sleep Timer is an ultra low-power timer which uses a 32.768 kHz crystal oscillator or a low power RC oscillator as clock source. The Sleep Timer runs continuously in all operating modes except active mode and PM3 and is typically used to get out of PM0, PM1, or PM2. See Section 12.8 for details. A built-in watchdog timer allows the CC1110Fx/CC1111Fx to reset itself in case the firmware hangs. When enabled, the watchdog timer must be cleared periodically, otherwise it will reset the device when it times out. See Section 12.13 for details. Timer 1 is a 16-bit timer which supports typical timer/counter functions such as input capture, output compare, and PWM functions. The timer has a programmable prescaler, a 16-bit period value, and three independent capture/compare channels. Each of the channels can be used as PWM outputs or to capture the timing of edges on input signals. A second order Delta-Sigma noise shaper mode is also supported for audio applications. See Section 12.6 for details. Timer 2 (MAC timer) is specially designed to support time-slotted protocols in software. The timer has a configurable timer period and a programmable prescaler range. See Section 12.7 for details. Timers 3 and Timer 4 are two 8-bit timers which supports typical timer/counter functions such as output compare and PWM functions. They have a programmable prescaler, an 8-bit period value, and two compare channels each, which can be used as PWM outputs. See Section 12.9 for details. USART 0 and USART 1 are each configurable as either an SPI master/slave or a UART. They provide hardware flow-control and double buffering on both RX and TX and are thus well suited for high-throughput, fullduplex applications. Each has its own highprecision baud-rate generator, hence leaving the ordinary timers free for other uses. When configured as an SPI slave they sample the input signal using SCK directly instead of using some over-sampling scheme and are therefore well-suited for high data rates. See Section 12.14 for details. The AES encryption/decryption core allows the user to encrypt and decrypt data using the AES algorithm with 128-bit keys. See Section 12.12 for details. The ADC supports 7 to 12 bits of resolution in a 30 kHz to 4 kHz bandwidth respectively. DC and audio conversions with up to eight input channels (P0) are possible (CC1111Fx is limited to six channels). The inputs can be selected as single ended or differential. The reference voltage can be internal, VDD, or a single ended or differential external signal. The ADC also has a temperature sensor input channel. The ADC can automate the process of periodic sampling or conversion over a sequence of channels. See Section 12.10 for details. The USB allows the CC1111Fx to implement a Full-Speed USB 2.0 compatible device. The USB has a dedicated 1 KB SRAM that is used for the endpoint FIFOs. 5 endpoints are available in addition to control endpoint 0. Each of these endpoints must be configured as Bulk/Interrupt or Isochronous and can be used as IN, OUT or IN/OUT. Double buffering of packets is also supported for endpoints 1 5. The maximum FIFO memory available for each endpoint is as follows: 32 bytes for endpoint 0, 32 bytes for endpoint 1, 64 bytes for endpoint 2, 128 bytes for endpoint 3, 256 bytes for endpoint 4, and 512 bytes for endpoint 5. When an endpoint is used as IN/OUT, the FIFO memory available for the endpoint can be distributed between IN and OUT depending on the demands of the application. The USB does not exist on the CC1110Fx. See Section 12.16 for details. 2 The I S can be used to send/receive audio samples to/from an external sound processor or DAC and may operate at full or half duplex. Samples of up to 16-bits resolution can be 2 used although the I S can be configured to send more low order bits if necessary to be compliant with the resolution of the receiver (up to 32 bit). The maximum bit-rate supported 2 is 3.5 Mbps. The I S can be configured as a master or slave device and supports both mono and stereo. Automatic -Law expansion and compression can also be configured. See Section 12.4.6.6 for details. SWRS033G Page 35 of 244 CC1110Fx / CC1111Fx 8.2 Radio CC1110Fx/CC1111Fx features an RF transceiver based on the industry-leading CC1101, 9 requiring very few external components. See Section 9 for details. Application Circuit Only a few external components are required for using the CC1110Fx/CC1111Fx. The recommended application circuit for CC1110Fx is shown in Figure 10. The recommended application circuits for CC1111Fx are shown in 9.1 Figure 12. The recommended CC1111Fx circuit uses a fundamental crystal. The external components are described in Table 28, and typical values are given in Table 29. Bias Resistor The bias resistor R271 is used to set an accurate bias current. 9.2 Balun and RF Matching The balanced RF input and output of CC1110Fx/CC1111Fx share two common pins and are designed for a simple, low-cost matching and balun network on the printed circuit board. The receive- and transmit switching at the CC1110Fx/CC1111Fx front-end are controlled by a dedicated on-chip function, eliminating the need for an external RX/TX-switch. A few passive external components combined with the internal RX/TX switch/termination circuitry ensure match in both RX and TX mode. Although CC1110Fx/CC1111Fx has a balanced RF input/output, the chip can be connected to a single-ended antenna with few external low cost capacitors and inductors. 9.3 The passive matching/filtering network connected to CC1110Fx/CC1111Fx should have the following differential impedance as seen from the RF-port (RF_P and RF_N) towards the antenna: Zout @ 315 MHz = 122 + j31 Zout @ 433 MHz = 116 + j41 Zout @ 868 MHz = 86.5 + j43 To ensure optimal matching of the CC1110Fx/CC1111Fx differential output it is highly recommended to follow the CC1110EM reference designs [1] or the CC1111 USBDongle Reference Design [4] as closely as possible. Gerber files and schematics for the reference designs are available for download from the TI website. Crystal The crystal oscillator for the CC1110Fx uses an external crystal X1, with two loading capacitors (C201 and C211) while the crystal oscillator for the CC1111Fx uses an external crystal X3, with two loading capacitors (C203 and C214) (see Figure 10, Figure 11, Figure 12, and Table 28). Note: The high speed crystal oscillator must be stable (SLEEP.XOSC_STB=1) before using the radio. The recommended application circuits also show the connections for an optional 32.768 kHz crystal oscillator with external crystal X2 and loading capacitors C181 and C171. This crystal can be used by the Sleep Timer if more accurate wake-up intervals are needed than what the internal RC oscillator can provide. When not using X2, P2_3 and P2_4 may be used as general IO pins. The loading capacitor values depend on the total load capacitance, CL, specified for the crystal. The total load capacitance seen between the crystal terminals should equal CL for the crystal to oscillate at the specified frequency. For the CC1110Fx using the crystal X1, the load capacitance CL is given as: CL 1 C Parasitic 1 1 C 211 C 201 The parasitic capacitance is constituted by pin input capacitance and PCB stray capacitance. SWRS033G Page 36 of 244 CC1110Fx / CC1111Fx Total parasitic capacitance is typically 2.5 pF. The crystal oscillator is amplitude regulated. This means that a high current is used to start up the oscillations. When the amplitude builds up, the current is reduced to what is necessary 9.4 Reference Signal The chip can alternatively be operated with a reference signal from 26 to 27 MHz (CC1110Fx) or 48 MHz (CC1111Fx) instead of a crystal. This input clock can either be a full-swing digital signal (0 V to VDD) or a sine wave of maximum 1 V peak-peak amplitude. The reference signal must be connected to the XOSC_Q1 input. The sine wave must be 9.5 connected to XOSC_Q1 using a serial capacitor. When using a full-swing digital signal this capacitor can be omitted. The XOSC_Q2 line must be left un-connected. The crystal loading capacitors and crystal inductor (if using X4) can be omitted when using a reference signal USB (CC1111Fx) For the CC1111Fx, the DP and DM pins need series resistors R262 and R263 for impedance matching and the D+ line must have a pull-up resistor, R264. The series resistors should match the 90 15% characteristic impedance of the USB bus. Notice that the pull-up resistor must be tied to a voltage source between 3.0 and 3.6 V (typically 3.3 V). The voltage source must be derived from or controlled by the VBUS power supply provided by the USB cable. In this way, 9.6 to maintain approximately 0.4 Vpp signal swing. This ensures a fast start-up, and keeps the drive level to a minimum. The ESR of the crystal should be within the specification in order to ensure a reliable start-up the pull-up resistor does not provide current to the D+ line when VBUS is removed. The pull-up resistor may be connected directly between VBUS and the D+ line. As an alternative, if the CC1111Fx firmware needs the ability to disconnect from the USB bus, an I/O pin on the CC1111Fx can be used to control the pull-up resistor. Power Supply Decoupling The power supply must be properly decoupled close to the supply pins. Note that decoupling capacitors are not shown in the application circuit. The placement and the size of the decoupling capacitors are very important to achieve the optimum performance. TI provides reference designs that should be followed closely ([1], [2], [3] and [4]). SWRS033G Page 37 of 244 CC1110Fx / CC1111Fx Figure 10: Application Circuit for CC1110Fx 315/433 MHz (excluding supply decoupling capacitors) 2.0 V - 3.6 V power supply RBIAS 27 AVDD_DREG 29 GUARD 28 R271 AVDD 26 AVDD 25 L241 L242 C235 L233 RF_N 24 2,10 DVDD L231 C233 L232 21 XOSC_Q1 20 XOSC_Q2 17 XOSC32_Q1 18 XOSC32_Q2 AVDD 22 L234 C231 C232 RF_P 23 DIE ATTACH PAD: 19 AVDD 30 DCOUPL C301 Antenna (50 Ohm) C241 C234 C235' L235 C236 Optional: C181 X2 X1 C171 Alternative filter that can be used to reduce the emission at 699 MHz below -54 dBm, for conducted measurements. C211 C201 Figure 11: Application Circuit for CC1110Fx 868/915 MHz (excluding supply decoupling capacitors) SWRS033G Page 38 of 244 CC1110Fx / CC1111Fx 3.0 V - 3.6 V power supply R264 RBIAS 27 GUARD 28 AVDD_DREG 29 4 P1_0 R271 AVDD 26 R262 C235 L233 RF_N 24 10 DP AVDD 22 L231 C233 C234 X2 X3 C171 L235 C236 Alternative filter that can be used to reduce the emission at 699 MHz below -54 dBm, for conducted measurements. Optional: C181 C235' L232 21 XOSC_Q1 17 XOSC32_Q1 18 XOSC32_Q2 30 DCOUPL C301 19 AVDD DIE ATTACH PAD: L234 C231 C232 RF_P 23 11 DM R263 20 XOSC_Q2 D- L242 L241 AVDD 25 2,12 DVDD D+ Antenna (50 Ohm) C241 C214 C203 Figure 12: Application Circuit for CC1111Fx 868/915 MHz with Fundamental Crystal (excluding supply decoupling capacitors) Component Description C301 Decoupling capacitor for on-chip voltage regulator to digital part C203/C214 Crystal loading capacitors (X3) C201/C211 Crystal loading capacitors (X1) L231/L241/C231 Low-pass filter/match L232/L242/C234/C241 Balun L233/L234/C233 Filter C234 DC block L235/C236 Alternative filter to reduce the emission at 699 MHz C235/C235' DC block or part of filter to reduce emission at 699 MHz C181/C171 Crystal loading capacitors if X2 is used. L281 Crystal inductor R271 Resistor for internal bias current reference R264 D+ Pull-up resistor R262/R263 D+ / D- series resistors for impedance matching X1 26 - 27 MHz crystal X2 32.768 kHz crystal, optional X3 48 MHz crystal (fundamental) Table 28: Overview of External Components (excluding supply decoupling capacitors) SWRS033G Page 39 of 244 CC1110Fx / CC1111Fx Component Value at 315 MHz Value at 433 MHz Value at 868/915 MHz Manufacturer C301 1 F 10%, 0402 X5R Murata GRM1555C series C201/C211 27 pF 5%, 0402 NP0 Murata GRM1555C series C203/C214 22 pF 5%, 0402 NP0 Murata GRM1555C series C231 6.8 pF 0.5 pF, 0402 NP0 3.9 pF 0.25 pF, 0402 NP0 1.0 pF 0.25 pF, 0402 NP0 Murata GRM1555C series C232 12 pF 5%, 0402 NP0 8.2 pF 0.5 pF, 0402 NP0 1.5 pF 0.25 pF, 0402 NP0 Murata GRM1555C series C233 6.8 pF 0.5 pF, 0402 NP0 5.6 pF 0.5 pF, 0402 NP0 3.3 pF 0.25 pF, 0402 NP0 Murata GRM1555C series C234 220 pF 5%, 0402 NP0 220 pF 5%, 0402 NP0 100 pF 5%, 0402 NP0 Murata GRM1555C series C235 220 pF 5%, 0402 NP0 220 pF 5%, 0402 NP0 100 pF 5%, 0402 NP0 Murata GRM1555C series C235' 12 pF 5%, 0402 NP0 Murata GRM1555C series C236 47 pF 5%, 0402 NP0 Murata GRM1555C series 1.5 pF 0.25 pF, 0402 NP0 Murata GRM1555C series C241 6.8 pF 0.5 pF, 0402 NP0 C171/C181 3.9 pF 0.25 pF, 0402 NP0 15pF 5%, 0402 NP0 Murata GRM1555C series L231 33 nH 5%, 0402 monolithic 27 nH 5%, 0402 monolithic 12 nH 5%, 0402 monolithic Murata LQG15HS series L232 18 nH 5%, 0402 monolithic 22 nH 5%, 0402 monolithic 18 nH 5%, 0402 monolithic Murata LQG15HS series L233 33 nH 5%, 0402 monolithic 27 nH 5%, 0402 monolithic 12 nH 5%, 0402 monolithic Murata LQG15HS series 12 nH 5%, 0402 monolithic Murata LQG15HS series 12 nH 5%, 0402 monolithic Murata LQG15HS series L242 18 nH 5%, 0402 monolithic Murata LQG15HS series L235 3.3 nH 5%, 0402 monolithic Murata LQG15HS series R262/R263 33 2%, 0402 Koa RK73 series 1.5 k 1%, 0402 Koa RK73 series L234 L241 33 nH 5%, 0402 monolithic 27 nH 5%, 0402 monolithic R264 R271 56 k 1%, 0402 Koa RK73 series X1 26.0 MHz surface mount crystal NDK, AT-41CD2 X2 32.768 kHz surface mount crystal (optional) Epson MC-306 Crystal Unit X3 48 MHz surface mount crystal Abracon ABM8 series Table 29: Bill of Materials for the CC1110Fx/CC1111Fx Application Circuits (subject to changes) SWRS033G Page 40 of 244 CC1110Fx / CC1111Fx 9.7 PCB Layout Recommendations The top layer should be used for signal routing, and the open areas should be filled with metallization connected to ground using several vias. The area under the chip is used for grounding and shall be connected to the bottom ground plane with several vias for good thermal performance and sufficiently low inductance to ground. In the CC1110EM reference designs [1] 9 vias are placed inside the exposed die attached pad. These vias should be "tented" (covered with solder mask) on the component side of the PCB to avoid migration of solder through the vias during the solder reflow process. The solder paste coverage should not be 100%. If it is, out gassing may occur during the reflow process, which may cause defects (splattering, solder balling). Using "tented" vias reduces the solder paste coverage below 100%. See Figure 13 for top solder resist and top paste masks. Each decoupling capacitor should be placed as close as possible to the supply pin it is supposed to decouple. The best routing is from the power line to the decoupling capacitor and then to the CC1110Fx supply pin. Supply power filtering is very important. Each decoupling capacitor ground pad should be connected to the ground plane using a separate via. Direct connections between neighboring power pins will increase noise coupling and should be avoided unless absolutely necessary. The external components should ideally be as small as possible (0402 is recommended) and surface mount devices are highly recommended. Please note that components smaller than those specified may have differing characteristics. Schematic, BOM, and layout Gerber files are all available from the TI website for both the CC1110EM reference designs [1], [2], [3] and the CC1111 USB Dongle reference design [4]. Figure 13: Left: Top Solder Resist Mask (negative). Right: Top Paste Mask. Circles are Vias. 10 8051 CPU This section describes the 8051 CPU core, with interrupts, memory, and instruction set. 10.1 8051 Introduction The CC1110Fx/CC1111Fx includes an 8-bit CPU core which is an enhanced version of the industry standard 8051 core. One clock per instruction cycle is used as opposed to 12 clocks per instruction cycle in the standard 8051. The enhanced 8051 core uses the standard 8051 instruction set. Instructions execute faster than the standard 8051 due to the following: Wasted bus states are eliminated. Since an instruction cycle is aligned with memory fetch when possible, most of the single byte instructions are performed in a single clock cycle. In addition to the speed SWRS033G Page 41 of 244 CC1110Fx / CC1111Fx improvement, the enhanced 8051 core also includes architectural enhancements: A second data pointer Extended 18-source interrupt unit The 8051 core is object code compatible with the industry standard 8051 microcontroller. That is, object code compiled with an industry standard 8051 compiler or assembler executes on the 8051 core and is functionally equivalent. However, because the 8051 core uses a different instruction-timing than many other 8051 variants, existing code with timing loops may require modification. Also because the peripheral units such as timers and serial ports differ from those on other 8051 cores, code which includes instructions using the peripheral units SFRs will not work correctly. 10.2 Memory The 8051 CPU architecture has four different memory spaces. The 8051 has separate memory spaces for program memory and data memory. The 8051 memory spaces are the following (see Section 10.2.1 and 10.2.2 for details): CODE. A 16-bit read-only memory space for program memory. DATA. An 8-bit read/write data memory space, which can be directly or indirectly, accessed by a single cycle CPU instruction, thus allowing fast access. The lower 128 bytes of the DATA memory space can be addressed either directly or indirectly, the upper 128 bytes only indirectly. XDATA. A 16-bit read/write data memory space, which usually requires 4 - 5 CPU instruction cycles to access, thus giving slow access. XDATA assesses is also slower in hardware than DATA accesses as the CODE and XDATA memory spaces share a common bus on the CPU core (instruction pre-fetch from CODE can not be performed in parallel with XDATA accesses). DMA transfers operation. and hardware debugger How the different memory spaces are mapped onto the three physical memories (8/16/32 KB flash program memory, 1/2/4 KB SRAM, and 2 hardware registers (SFR, radio, I S, and USB (CC1111Fx)) is described in Sections 10.2.1 and 10.2.2. 10.2.1 Memory Map This section gives an overview of the memory map. Both the DATA and the SFR memory space is mapped to the XDATA and CODE memory space as shown in Figure 14, Figure 15, and Figure 16 (the CODE and XDATA memory spaces are mapped identically), and CC1110FX/CC1111FX has what can be called a unified memory space. SFR. A 7-bit read/write register memory space, which can be directly accessed by a single CPU instruction. For SFRs whose address is divisible by eight, each bit is also individually addressable. Mapping all the memory spaces to XDATA allows the DMA controller access to all physical memory and thus allows DMA transfers between the different 8051 memory spaces. This also means that any instruction that read, write, or manipulate an XDATA variable can be used on the entire unified memory space, except writing to or changing data in flash. The four different memory spaces are distinct in the 8051 architecture, but are partly overlapping in the CC1110Fx/CC1111Fx to ease Mapping all memory spaces to the CODE memory space is primarily done to allow program execution out of the SRAM/XDATA. SWRS033G Page 42 of 244 CC1110Fx / CC1111Fx 0xFF 0x00 DATA Memory Space 0xFFFF Fast Access RAM 0xFF00 0xFEFF Unimplemented 0xF300 0xF2FF 0xF000 0xEFFF 0xFF 0x80 SFR Memory Space 0xE000 0xDFFF 0xDF80 0xDF00 0xDEFF 0xFFFF 0xDE40 0xDE3F Slow Access RAM / Program Memory in RAM 1 KB SRAM Unimplemented Hardware SFR Registers Hardware Registers Hardware Radio Registers / I2S Registers Unimplemented USB Register ( ) 0xDE00 0xDDFF USB Registers ( ) Unimplemented XDATA Memory Space 0x2000 0x1FFF 0x0000 Non-Volatile Program Memory 8 KB Flash 0x0000 0xFFFF CODE Memory Space 0x0000 Figure 14: CC1110F8/CC1111F8 Memory Mapping SWRS033G Page 43 of 244 CC1110Fx / CC1111Fx 0xFF 0x00 DATA Memory Space 0xFFFF 0xFF00 0xFEFF 0xF700 0xF6FF Fast Access RAM Unimplemented Slow Access RAM / Program Memory in RAM 0xF000 0xEFFF 0xFF 0x80 SFR Memory Space 0xE000 0xDFFF 0xDF80 0xDF00 0xDEFF 0xFFFF 0xDE40 0xDE3F 0xDE00 0xDDFF XDATA Memory Space 2 KB SRAM Unimplemented Hardware SFR Registers Hardware Registers Hardware Radio Registers / I2S Registers Unimplemented USB Register ( ) USB Registers ( ) Unimplemented 0x4000 0x3FFF Non-Volatile Program Memory 16 KB Flash 0x0000 0x0000 0xFFFF CODE Memory Space 0x0000 Figure 15: CC1110F16/CC1111F16 Memory Mapping SWRS033G Page 44 of 244 CC1110Fx / CC1111Fx 0xFF 0xFFFF DATA Memory Space 0x00 Fast Access RAM 0xFF00 0xFEFF 4 KB SRAM Slow Access RAM / Program Memory in RAM 0xF000 0xEFFF 0xFF 0x80 0xE000 0xDFFF SFR Memory Space 0xDF80 0xDF00 0xDEFF 0xFFFF 0xDE40 0xDE3F 0xDE00 0xDDFF Unimplemented Hardware SFR Registers Hardware Registers Hardware Radio Registers / I2S Registers Unimplemented USB Register ( USB Registers ( ) ) Unimplemented 0x8000 0x7FFF XDATA Memory Space Non-Volatile Program Memory 32 KB Flash 0x0000 0x0000 0xFFFF CODE Memory Space 0x0000 Figure 16: CC1110F32/CC1111F32 Memory Mapping Details about the mapping of all 8051 memory spaces are given in the next section. 10.2.2 8051 Memory Space This section describes the details of each standard 8051 memory space. Any differences between the standard 8051 and CC1110Fx/CC1111Fx is described. 10.2.2.1 XDATA Memory Space On a standard 8051 this memory space would hold any extra RAM available. consideration that the first address of usable SRAM start at 0xF000 instead of 0x0000. The 350 bytes of XDATA in location 0xFDA2 0xFEFF on CC1110F32 and CC1111F32 do not retain data when power modes PM2 or PM3 are entered. Refer to Section 12.1.2 on Page 77 for a detailed description of power modes. The 256 bytes from 0xFF00 to 0xFFFF are the DATA memory space mapped to XDATA. These bytes are also reached through the DATA memory space. In addition the following is mapped into the XDATA memory space: The 8, 16, and 32 KB flash program memory is mapped into the address ranges 0x0000 0x1FFF, 0x0000 - 0x3FFF, and 0x0000 0x7FFF respectively. The CC1110Fx/CC1111Fx has a total of 1, 2, or 4 KB SRAM, starting at address 0xF000. Compilers/assemblers must take into SWRS033G Radio registers are mapped address range 0xDF00 - 0xDF3D. into I S registers are mapped into the address range 0xDF40 - 0xDF48. 2 All SFR except the registers shown in gray in Table 30 are mapped into address range 0xDF80 - 0xDFFF. Page 45 of 244 CC1110Fx / CC1111Fx The USB registers are mapped into the address range 0xDE00 - 0xDE3F on the CC1111Fx, but are not implemented on the CC1110Fx. Unlike on a standard 8051, the SFRs are also accessible through the XDATA and CODE memory space at the address range 0xDF80 0xDFFF. This memory mapping allows the DMA controller (and the CPU) access to all the physical memories in a single unified address space. Some CPU-specific SFRs reside inside the CPU core and can only be accessed using the SFR memory space and not through the duplicate mapping into XDATA/CODE memory space. These registers are shown in gray in Table 30. Be aware that these registers can not be accessed using DMA. Be aware that access to unimplemented areas in the unified memory space will give an undefined result. 10.2.2.2 10.2.3 CODE Memory Space On a standard 8051 this memory space would hold the program memory, where the MCU reads the program/instructions. All memory spaces are mapped into the CODE memory space and the mapping is identical to the XDATA memory space, hence the CC1110Fx/CC1111Fx has what can be referred to as a unified memory space. Due to this, the CC1110Fx/CC1111Fx allows execution of a program stored in SRAM. This allows the program to be easily updated without writing to flash (which have a limited erase/write cycles) This is particularly useful on the CC1111Fx, where parts of the firmware can be downloaded from the windows USB driver. Executing a program from SRAM instead of flash will also result in a lower power consumption and may be interesting for battery powered devices. 10.2.2.3 DATA Memory Space The 8-bit address range of DATA memory space is mapped into address 0xFF00 0xFFFF and is accessible through the unified memory space. Just like on a standard 8051, the upper 128 byte share address with the SFR and can only be accessed indirectly, the stack is normally located here. The lower 48 bytes are reserved, and hold 4 register banks used by the MCU. The 16 bytes on addresses 0x20 to 0x2F are bit addressable. The DATA memory will retain its contents in all four power modes. 10.2.2.4 SFR Memory Space The SFR memory space is identical to a standard 8051. The 128 hardware SFRs are accessed through this memory space. 10.2.3.1 Physical Memory SRAM The CC1110Fx/CC1111Fx contains static RAM. At power-on the contents of RAM is undefined. The RAM size is 1, 2, or 4 KB in total, mapped to the memory range 0xF000 - 0xFFFF. In the F8 version, memory range 0xF300 - 0xFEFF is unimplemented while on the F16 version, memory range 0xF700 - 0xFEFF is unimplemented. The memory locations 0xFDA2 - 0xFEFF on the F32 version consist of 350 bytes in unified memory space which do not retain data when power modes PM2 or PM3 is entered. All other RAM memory locations are retained in all power modes. 10.2.3.2 Flash Memory The on-chip flash memory 16384, or 32768 bytes (F8, flash memory is primarily program code. The flash following features: consists of 8192, F16, and F32). The intended to hold memory has the Flash page erase time: 20 ms Flash chip (mass) erase time: 200 ms Flash write time (2 bytes): 20 s Data retention (at room temperature): 100 years Program/erase 1,000 cycles endurance: Minimum The flash memory consists of the Flash Main Pages (up to 32 times 1 KB) which are where the CPU reads program code and data. The flash memory also contains a Flash Information Page (1 KB) which contains the Flash Lock Bits. The lock protect bits are written as a normal flash write to FWDATA but the Debug Interface needs to select the Flash Information Page first instead of the Flash Main Page. The Information Page is selected through the Debug Configuration which is SWRS033G Page 46 of 244 CC1110Fx / CC1111Fx written through the Debug Interface only. The Flash Controller (see Section 12.3) is used to write and erase the contents of the flash main memory. control features that are not available in the standard 8051. The additional SFRs are used to interface with the peripheral units and RF transceiver. When the CPU reads instructions from flash memory, it fetches the next instruction through a cache. The instruction cache is provided mainly to reduce power consumption by reducing the amount of time the flash memory itself is accessed. The use of the instruction cache may be disabled with the MEMCTR.CACHDIS register bit, but doing so will increase power consumption. Table 30 shows the address to all SFRs in CC1110Fx/CC1111Fx. The 8051 internal SFRs are shown with grey background, while the other SFRs are specific to CC1110Fx/CC1111Fx. 10.2.3.3 Note: All internal SFRs (shown with grey background in Table 30, can only be accessed through SFR memory space as these registers are not mapped into XDATA memory space. Table 31 lists the additional SFRs that are not standard 8051 peripheral SFRs or CPUinternal SFRs. The additional SFRs are described in the relevant sections for each peripheral function. Special Function Registers The Special Function Registers (SFRs) control several of the features of the 8051 CPU core and/or peripherals. Many of the 8051 core SFRs are identical to the standard 8051 SFRs. However, there are additional SFRs that 8 Bytes 80 P0 SP DPL0 DPH0 DPL1 DPH1 88 TCON P0IFG P1IFG P2IFG PICTL P1IEN 90 P1 RFIM DPS MPAGE 98 S0CON IEN2 S1CON T2CT T2PR T2CTL 9F A0 P2 WORIRQ WORCTRL WOREVT0 WOREVT1 WORTIME0 WORTIME1 A7 A8 IEN0 IP0 FWT FADDRL FADDRH FCTL B0 U0CSR PCON 87 P0INP 8F ENDIAN 97 FWDATA AF ENCDI ENCDO ENCCS ADCCON1 ADCCON2 ADCCON3 B7 ADCH RNDL RNDH SLEEP BF U0UCR U0GCR CLKCON MEMCTR C7 B8 IEN1 IP1 ADCL C0 IRCON U0DBUF U0BAUD WDCTL T3CNT T3CTL T3CCTL0 T3CC0 T3CCTL1 T3CC1 CF C8 D0 PSW DMAIRQ DMA1CFGL DMA1CFGH DMA0CFGL DMA0CFGH DMAARM DMAREQ D7 D8 TIMIF RFD T1CC0L T1CC0H T1CC1L T1CC1H T1CC2L T1CC2H DF E0 ACC RFST T1CNTL T1CNTH T1CTL T1CCTL0 T1CCTL1 T1CCTL2 E7 E8 IRCON2 RFIF T4CNT T4CTL T4CCTL0 T4CC0 T4CCTL1 T4CC1 EF F0 B PERCFG ADCCFG P0SEL P1SEL P2SEL P1INP P2INP F7 F8 U1CSR U1DBUF U1BAUD U1UCR U1GCR P0DIR P1DIR P2DIR FF Table 30: SFR Address Overview SWRS033G Page 47 of 244 CC1110Fx / CC1111Fx Register Name SFR Address Module Description Retention6 ADCCON1 0xB4 ADC ADC Control 1 Y ADCCON2 0xB5 ADC ADC Control 2 Y ADCCON3 0xB6 ADC ADC Control 3 Y ADCL 0xBA ADC ADC Data Low Y ADCH 0xBB ADC ADC Data High Y RNDL 0xBC ADC Random Number Generator Data Low Y RNDH 0xBD ADC Random Number Generator Data High Y ENCDI 0xB1 AES Encryption/Decryption Input Data N ENCDO 0xB2 AES Encryption/Decryption Output Data N ENCCS 0xB3 AES Encryption/Decryption Control and Status N DMAIRQ 0xD1 DMA DMA Interrupt Flag Y DMA1CFGL 0xD2 DMA DMA Channel 1 - 4 Configuration Address Low Y DMA1CFGH 0xD3 DMA DMA Channel 1 - 4 Configuration Address High Y DMA0CFGL 0xD4 DMA DMA Channel 0 Configuration Address Low Y DMA0CFGH 0xD5 DMA DMA Channel 0 Configuration Address High Y DMAARM 0xD6 DMA DMA Channel Arm Y DMAREQ 0xD7 DMA DMA Channel Start Request and Status Y FWT 0xAB FLASH Flash Write Timing Y FADDRL 0xAC FLASH Flash Address Low Y FADDRH 0xAD FLASH Flash Address High Y FCTL 0xAE FLASH Flash Control [7:1]Y, [1:0]N FWDATA 0xAF FLASH Flash Write Data Y P0IFG 0x89 IOC Port 0 Interrupt Status Flag Y P1IFG 0x8A IOC Port 1 Interrupt Status Flag Y P2IFG 0x8B IOC Port 2 Interrupt Status Flag Y PICTL 0x8C IOC Port Pins Interrupt Mask and Edge Y P1IEN 0x8D IOC Port 1 Interrupt Mask Y P0INP 0x8F IOC Port 0 Input Mode Y PERCFG 0xF1 IOC Peripheral I/O Control Y ADCCFG 0xF2 IOC ADC Input Configuration Y P0SEL 0xF3 IOC Port 0 Function Select Y P1SEL 0xF4 IOC Port 1 Function Select Y P2SEL 0xF5 IOC Port 2 Function Select Y P1INP 0xF6 IOC Port 1 Input Mode Y P2INP 0xF7 IOC Port 2 Input Mode Y P0DIR 0xFD IOC Port 0 Direction Y P1DIR 0xFE IOC Port 1 Direction Y P2DIR 0xFF IOC Port 2 Direction Y MEMCTR 0xC7 MEMORY Memory System Control Y 6 Registers without retention are in their reset state after PM2 or PM3. This is only applicable for registers / bits that are defined as R/W SWRS033G Page 48 of 244 CC1110Fx / CC1111Fx Register Name SFR Address Module Description Retention6 SLEEP 0xBE PMC Sleep Mode Control [6:2]Y, [7,1:0]N CLKCON 0xC6 PMC Clock Control Y RFIM 0x91 RF RF Interrupt Mask Y RFD 0xD9 RF RF Data N RFIF 0xE9 RF RF Interrupt flags Y RFST 0xE1 RF RF Strobe Commands NA WORIRQ 0xA1 Sleep Timer Sleep Timer Interrupts Y WORCTRL 0xA2 Sleep Timer Sleep Timer Control Y WOREVT0 0xA3 Sleep Timer Sleep Timer Event 0 Timeout Low Byte Y WOREVT1 0xA5 Sleep Timer Sleep Timer Event 0 Timeout High Byte Y WORTIME0 0xA4 Sleep Timer Sleep Timer Low Byte Y WORTIME1 0xA6 Sleep Timer Sleep Timer High Byte Y T1CC0L 0xDA Timer1 Timer 1 Channel 0 Capture/Compare Value Low Y T1CC0H 0xDB Timer1 Timer 1 Channel 0 Capture/Compare Value High Y T1CC1L 0xDC Timer1 Timer 1 Channel 1 Capture/Compare Value Low Y T1CC1H 0xDD Timer1 Timer 1 Channel 1 Capture/Compare Value High Y T1CC2L 0xDE Timer1 Timer 1 Channel 2 Capture/Compare Value Low Y T1CC2H 0xDF Timer1 Timer 1 Channel 2 Capture/Compare Value High Y T1CNTL 0xE2 Timer1 Timer 1 Counter Low Y T1CNTH 0xE3 Timer1 Timer 1 Counter High Y T1CTL 0xE4 Timer1 Timer 1 Control and Status Y T1CCTL0 0xE5 Timer1 Timer 1 Channel 0 Capture/Compare Control Y T1CCTL1 0xE6 Timer1 Timer 1 Channel 1 Capture/Compare Control Y T1CCTL2 0xE7 Timer1 Timer 1 Channel 2 Capture/Compare Control Y T2CT 0x9C Timer2 Timer 2 Timer Count N T2PR 0x9D Timer2 Timer 2 Prescaler N T2CTL 0x9E Timer2 Timer 2 Control N T3CNT 0xCA Timer3 Timer 3 Counter Y T3CTL 0xCB Timer3 Timer 3 Control Y,[2]N T3CCTL0 0xCC Timer3 Timer 3 Channel 0 Capture/Compare Control Y T3CC0 0xCD Timer3 Timer 3 Channel 0 Capture/Compare Value Y T3CCTL1 0xCE Timer3 Timer 3 Channel 1 Capture/Compare Control Y T3CC1 0xCF Timer3 Timer 3 Channel 1 Capture/Compare Value Y T4CNT 0xEA Timer4 Timer 4 Counter Y T4CTL 0xEB Timer4 Timer 4 Control Y,[2]N T4CCTL0 0xEC Timer4 Timer 4 Channel 0 Capture/Compare Control Y T4CC0 0xED Timer4 Timer 4 Channel 0 Capture/Compare Value Y T4CCTL1 0xEE Timer4 Timer 4 Channel 1 Capture/Compare Control Y T4CC1 0xEF Timer4 Timer 4 Channel 1 Capture/Compare Value Y TIMIF 0xD8 TMINT Timers 1/3/4 Joint Interrupt Mask/Flags Y U0CSR 0x86 USART0 USART 0 Control and Status Y U0DBUF 0xC1 USART0 USART 0 Receive/Transmit Data Buffer Y SWRS033G Page 49 of 244 CC1110Fx / CC1111Fx Register Name SFR Address Module Description Retention6 U0BAUD 0xC2 USART0 USART 0 Baud Rate Control Y U0UCR 0xC4 USART0 USART 0 UART Control Y,[7]N U0GCR 0xC5 USART0 USART 0 Generic Control Y U1CSR 0xF8 USART1 USART 1 Control and Status Y U1DBUF 0xF9 USART1 USART 1 Receive/Transmit Data Buffer Y U1BAUD 0xFA USART1 USART 1 Baud Rate Control Y U1UCR 0xFB USART1 USART 1 UART Control Y,[7]N U1GCR 0xFC USART1 USART 1 Generic Control Y ENDIAN 0x95 MEMORY USB Endianess Control (CC1111Fx) Y WDCTL 0xC9 WDT Watchdog Timer Control Y Table 31: CC1110Fx/CC1111Fx Specific SFR Overview 10.2.3.4 Radio Registers The radio registers are all related to Radio configuration and control. The RF registers can only be accessed through XDATA memory space and reside in address range 0xDF00 0xDF3D. Table 32 gives a descriptive overview of these registers. Each register is described in detail in Section 13.19, starting on Page 210. XDATA Address Register Description Retention7 0xDF00 SYNC1 Sync word, high byte Y 0xDF01 SYNC0 Sync word, low byte Y 0xDF02 PKTLEN Packet length Y 0xDF03 PKTCTRL1 Packet automation control Y 0xDF04 PKTCTRL0 Packet automation control Y 0xDF05 ADDR Device address Y 0xDF06 CHANNR Channel number Y 0xDF07 FSCTRL1 Frequency synthesizer control Y 0xDF08 FSCTRL0 Frequency synthesizer control Y 0xDF09 FREQ2 Frequency control word, high byte Y 0xDF0A FREQ1 Frequency control word, middle byte Y 0xDF0B FREQ0 Frequency control word, low byte Y 0xDF0C MDMCFG4 Modem configuration Y 0xDF0D MDMCFG3 Modem configuration Y 0xDF0E MDMCFG2 Modem configuration Y 0xDF0F MDMCFG1 Modem configuration Y 0xDF10 MDMCFG0 Modem configuration Y 0xDF11 DEVIATN Modem deviation setting Y 0xDF12 MCSM2 Main Radio Control State Machine configuration Y 0xDF13 MCSM1 Main Radio Control State Machine configuration Y 7 Registers without retention are in their reset state after PM2 or PM3. This is only applicable for registers / bits that are defined as R/W SWRS033G Page 50 of 244 CC1110Fx / CC1111Fx XDATA Address Register Description Retention7 0xDF14 MCSM0 Main Radio Control State Machine configuration Y 0xDF15 FOCCFG Frequency Offset Compensation configuration Y 0xDF16 BSCFG Bit Synchronization configuration Y 0xDF17 AGCCTRL2 AGC control Y 0xDF18 AGCCTRL1 AGC control Y 0xDF19 AGCCTRL0 AGC control Y 0xDF1A FREND1 Front end RX configuration Y 0xDF1B FREND0 Front end TX configuration Y 0xDF1C FSCAL3 Frequency synthesizer calibration N 0xDF1D FSCAL2 Frequency synthesizer calibration N 0xDF1E FSCAL1 Frequency synthesizer calibration N 0xDF1F FSCAL0 Frequency synthesizer calibration Y Reserved Y 0xDF20 0xDF22 0xDF23 TEST2 Various Test Settings Y 0xDF24 TEST1 Various Test Settings Y 0xDF25 TEST0 Various Test Settings Y 0xDF27 PA_TABLE7 PA output power setting 7 Y 0xDF28 PA_TABLE6 PA output power setting 6 Y 0xDF29 PA_TABLE5 PA output power setting 5 Y 0xDF2A PA_TABLE4 PA output power setting 4 Y 0xDF2B PA_TABLE3 PA output power setting 3 Y 0xDF2C PA_TABLE2 PA output power setting 2 Y 0xDF2D PA_TABLE1 PA output power setting 1 Y 0xDF2E PA_TABLE0 PA output power setting 0 Y 0xDF2F IOCFG2 Radio test signal configuration (P1_7) Y 0xDF30 IOCFG1 Radio test signal configuration (P1_6) Y 0xDF31 IOCFG0 Radio test signal configuration (P1_5) Y 0xDF36 PARTNUM Chip ID[15:8] NA 0xDF37 VERSION Chip ID[7:0] NA 0xDF38 FREQEST Frequency Offset Estimate NA 0xDF39 LQI Link Quality Indicator NA 0xDF3A RSSI Received Signal Strength Indication NA 0xDF3B MARCSTATE Main Radio Control State NA 0xDF3C PKTSTATUS Packet status NA 0xDF3D VCO_VC_DAC PLL calibration current NA Table 32: Overview of RF Registers 10.2.3.5 2 2 I S Registers 2 The I S registers are all related to I S 2 configuration and control. The I S registers can only be accessed through XDATA memory space and reside in address range 0xDF40 0xDF48. Table 33 gives a descriptive overview of these registers. Each register is described in detail in Section 12.15.13, starting on Page 165. SWRS033G Page 51 of 244 CC1110Fx / CC1111Fx XDATA Address Register Description Retention8 0xDF40 I2SCFG0 I2S Configuration Register 0 Y 0xDF41 I2SCFG1 I2S Configuration Register 1 Y 0xDF42 0xDF43 0xDF44 0xDF45 0xDF46 0xDF47 0xDF48 I2SDATL 2 N 2 N 2 NA 2 NA 2 Y 2 Y 2 Y I S Data Low Byte I2SDATH I S Data High Byte I2SWCNT I2SSTAT I S Word Count Register I S Status Register I2SCLKF0 I2SCLKF1 I2SCLKF2 I S Clock Configuration Register 0 I S Clock Configuration Register 1 I S Clock Configuration Register 2 2 Table 33: Overview of I S Registers 8 Registers without retention are in their reset state after PM2 or PM3. This is only applicable for registers / bits that are defined as R/W 10.2.3.6 USB Registers The USB registers are all related to USB configuration and control. The USB registers can only be accessed through XDATA memory space and reside in address range 0xDE00 - 0xDE3F. These registers can be divided into three groups: The Common USB Registers (Table 34), The Indexed Endpoint Registers (Table 35), and the Endpoint FIFO XDATA Address Register Description 0xDE00 USBADDR Function Address 0xDE01 USBPOW Power/Control Register 0xDE02 USBIIF IN Endpoints and EP0 Interrupt Flags 0xDE03 0xDE04 Registers (Table 36). Each register is described in detail in Section 12.16.11, starting on Page 177. Notice that the upper register addresses 0xDE2C - 0xDE3F are reserved. Note: All USB registers lose data in PM2 and PM3, meaning that these power modes cannot be used on the CC1111Fx Reserved USBOIF 0xDE05 OUT Endpoints Interrupt Flags Reserved 0xDE06 USBCIF Common USB Interrupt Flags 0xDE07 USBIIE IN Endpoints and EP0 Interrupt Enable Mask 0xDE08 0xDE09 Reserved USBOIE 0xDE0A Out Endpoints Interrupt Enable Mask Reserved 0xDE0B USBCIE Common USB Interrupt Enable Mask 0xDE0C USBFRML Current Frame Number (Low byte) 0xDE0D USBFRMH Current Frame Number (High byte) 0xDE0E USBINDEX Selects current endpoint. Make sure this register has the required value before any of the registers in Table 35 are accessed. This register must be set to a value in the range 0 - 5. Table 34: Overview of Common USB Registers SWRS033G Page 52 of 244 CC1110Fx / CC1111Fx XDATA Address Register Description Valid USBINDEX 0xDE10 USBMAXI Max. packet size for IN endpoint 1-5 USBCS0 EP0 Control and Status (USBINDEX = 0) 0 USBCSIL IN EP{1 - 5} Control and Status Low 1-5 0xDE12 USBCSIH IN EP{1 - 5} Control and Status High 1-5 0xDE13 USBMAXO Max. packet size for OUT endpoint 1-5 0xDE14 USBCSOL OUT EP{1 - 5} Control and Status Low 1-5 0xDE15 USBCSOH OUT EP{1 - 5} Control and Status High 1-5 USBCNT0 Number of received bytes in EP0 FIFO (USBINDEX = 0) 0 USBCNTL Number of bytes in OUT FIFO Low 1-5 USBCNTH Number of bytes in OUT FIFO High 1-5 Value(s) 0xDE11 0xDE16 0xDE17 Table 35: Overview of Indexed Endpoint Registers XDATA Address Register Description 0xDE20 USBF0 Endpoint 0 FIFO 0xDE22 USBF1 Endpoint 1 FIFO 0xDE24 USBF2 Endpoint 2 FIFO 0xDE26 USBF3 Endpoint 3 FIFO 0xDE28 USBF4 Endpoint 4 FIFO 0xDE2A USBF5 Endpoint 5 FIFO Table 36: Overview of Endpoint FIFO Registers 10.2.4 XDATA Memory Access The CC1110Fx/CC1111Fx provides an additional SFR named MPAGE. This register is used during instructions MOVX A,@Ri and MOVX @Ri,A. MPAGE gives the 8 most significant address bits, while the register Ri gives the 8 least significant bits. In some 8051 implementations, this type of XDATA access is performed using P2 to give the most significant address bits. Existing software may therefore have to be adapted to make use of MPAGE instead of P2. MPAGE (0x93) - Memory Page Select Bit Field Name Reset R/W Description 7:0 MPAGE[7:0] 0x00 R/W Memory page, high-order bits of address in MOVX instruction 10.2.5 Memory Arbiter The CC1110Fx/CC1111Fx includes a memory arbiter which handles CPU and DMA access to all memory space. A control register MEMCTR is used to control the flash cache. The MEMCTR register is described below. SWRS033G Page 53 of 244 CC1110Fx / CC1111Fx MEMCTR (0xC7) - Memory Arbiter Control Bit Field Name 7:2 1 0 CACHDIS Reset R/W Description 0 R/W Not used 0 R/W Flash cache disable. Invalidates contents of instruction cache and forces all instruction read accesses to read straight from flash memory. Disabling will increase power consumption and is provided for debug purposes. 1 PREFDIS R/W 0 Cache enabled 1 Cache disabled Flash prefetch disable. When set prefetch of flash data is disabled, when cleared the next two bytes in flash are fetched when last byte in cache is read. 0 Prefetch enabled 1 Prefetch disabled 10.3 CPU Registers This section describes the internal registers found in the CPU. 10.3.1 Data Pointers The CC1110Fx/CC1111Fx has two data pointers, DPTR0 and DPTR1, to accelerate the movement of data blocks to/from memory. The data pointers are generally used to access CODE or XDATA space e.g. The data pointer select bit, bit 0 in the Data Pointer Select register DPS, chooses which data pointer to use during the execution of an instruction that uses the data pointer, e.g. in one of the above instructions. The data pointers are two bytes consisting of the following SFRs: MOVC A,@A+DPTR wide DPTR0 - DPH0:DPL0 DPTR1 - DPH1:DPL1 MOV A,@DPTR. DPH0 (0x83) - Data Pointer 0 High Byte Bit Field Name Reset R/W Description 7:0 DPH0[7:0] 0 R/W Data pointer 0, high byte DPL0 (0x82) - Data Pointer 0 Low Byte Bit Field Name Reset R/W Description 7:0 DPL0[7:0] 0 R/W Data pointer 0, low byte DPH1 (0x85) - Data Pointer 1 High Byte Bit Field Name Reset R/W Description 7:0 DPH1[7:0] 0 R/W Data pointer 1, high byte DPL1 (0x84) - Data Pointer 1 Low Byte Bit Field Name Reset R/W Description 7:0 DPL1[7:0] 0 R/W Data pointer 1, low byte SWRS033G Page 54 of 244 CC1110Fx / CC1111Fx DPS (0x92) - Data Pointer Select Bit Field Name 7:1 0 DPS 10.3.2 Reset R/W Description 0 R/W Not used 0 R/W Data pointer select 0 DPTR0 1 DPTR1 Registers R0 - R7 10.3.3 The CC1110Fx/CC1111Fx provides four register banks of eight registers each. These register banks are in the DATA memory space at addresses 0x00 - 0x07, 0x08 - 0x0F, 0x10 0x17 and 0x18 - 0x1F and are mapped to address range 0xFF00 to 0xFF1F in the unified memory space. Each register bank contains the eight 8-bit register R0 - R7. The register bank to be used is selected through the Program Status Word PSW.RS[1:0]. Program Status Word The Program Status Word (PSW) contains several bits that show the current state of the CPU. The Program Status Word is accessible as an SFR and it is bit-addressable. The PSW register contains the Carry flag, Auxiliary Carry flag for BCD operations, Register Select bits, Overflow flag, and Parity flag. Two bits in PSW are uncommitted and can be used as userdefined status flags. PSW (0xD0) - Program Status Word Bit Field Name Reset R/W Description 7 CY 0 R/W Carry flag. Set to 1 when the last arithmetic operation resulted in a carry (during addition) or borrow (during subtraction), otherwise cleared to 0 by all arithmetic operations. 6 AC 0 R/W Auxiliary carry flag for BCD operations. Set to 1 when the last arithmetic operation resulted in a carry into (during addition) or borrow from (during subtraction) the high order nibble, otherwise cleared to 0 by all arithmetic operations. 5 F0 0 R/W User-defined, bit-addressable 4:3 RS[1:0] 00 R/W Register bank select bits. Selects which set of R7 - R0 registers to use from four possible register banks in DATA space. 00 Bank 0, 0x00 - 0x07 01 Bank 1, 0x08 - 0x0F 10 Bank 2, 0x10 - 0x17 11 Bank 3, 0x18 - 0x1F 2 OV 0 R/W Overflow flag, set by arithmetic operations. Set to 1 when the last arithmetic operation resulted in a carry (addition), borrow (subtraction), or overflow (multiply or divide). Otherwise, the bit is cleared to 0 by all arithmetic operations. 1 F1 0 R/W User-defined, bit-addressable 0 P 0 R/W Parity flag, parity of accumulator set by hardware to 1 if it contains an odd number of 1's, otherwise it is cleared to 0 10.3.4 Accumulator ACC is the accumulator. This is the source and destination of most arithmetic instructions, data transfer and other instructions. The mnemonic for the accumulator (in instructions involving the accumulator) refers to A instead of ACC. SWRS033G Page 55 of 244 CC1110Fx / CC1111Fx ACC (0xE0) - Accumulator Bit Field Name Reset R/W Description 7:0 ACC[7:0] 0x00 R/W Accumulator 10.3.5 B Register The B register is used as the second 8-bit argument during execution of multiply and divide instructions. When not used for these purposes it may be used as a scratch-pad register to hold temporary data. B (0xF0) - B Register Bit Field Name Reset R/W Description 7:0 B[7:0] 0x00 R/W B register. Used in MUL and DIV instructions. 10.3.6 Stack Pointer The stack resides in DATA memory space and grows upwards. The PUSH instruction first increments the Stack Pointer (SP) and then copies the byte into the stack. The Stack Pointer is initialized to 0x07 after a reset and it is incremented once to start from location 0x08, which is the first register (R0) of the second register bank. Thus, in order to use more than one register bank, the SP should be initialized to a different location not used for data storage. SP (0x81) - Stack Pointer Bit Field Name Reset R/W Description 7:0 SP[7:0] 0x07 R/W Stack Pointer 10.4 Instruction Set Summary The 8051 instruction set is summarized in Table 37. All mnemonics copyrighted Intel Corporation 1980. can be anywhere within the 8/16/32 KB CODE memory space. addr11 - 11-bit destination address. Used by ACALL and AJMP. The branch will be within the same 2 KB page of program memory as the first byte of the following instruction. The following conventions are used in the instruction set summary: Rn - Register R7 - R0 of the currently selected register bank. rel - Signed (two's complement) 8-bit offset byte. Used by SJMP and all conditional jumps. Range is -128 to +127 bytes relative to first byte of the following instruction. direct - 8-bit internal data location's address. This can be DATA area (0x00 0x7F) or SFR area (0x80 - 0xFF). @Ri - 8-bit internal data location, DATA area (0x00 - 0xFF) addressed indirectly through register R1 or R0. #data - 8-bit constant included in instruction. #data16 - 16-bit constant included in instruction. bit - direct addressed bit in DATA area or SFR. The instructions that affect CPU flag settings located in PSW are listed in Table 38 on Page 60. Note that operations on the PSW register or bits in PSW will also affect the flag settings. addr16 - 16-bit destination address. Used by LCALL and LJMP. A branch SWRS033G Page 56 of 244 CC1110Fx / CC1111Fx Mnemonic Description Hex Opcode Bytes Cycles ADD A,Rn Add register to accumulator 0x28 - 0x2F 1 1 ADD A,direct Add direct byte to accumulator 0x25 2 2 ADD A,@Ri Add indirect RAM to accumulator 0x26 - 0x27 1 2 ADD A,#data Add immediate data to accumulator 0x24 2 2 ADDC A,Rn Add register to accumulator with carry flag 0x38 - 0x3F 1 1 ADDC A,direct Add direct byte to A with carry flag 0x35 2 2 ADDC A,@Ri Add indirect RAM to A with carry flag 0x36 - 0x37 1 2 ADDC A,#data Add immediate data to A with carry flag 0x34 2 2 SUBB A,Rn Subtract register from A with borrow 0x98 - 0x9F 1 1 SUBB A,direct Subtract direct byte from A with borrow 0x95 2 2 SUBB A,@Ri Subtract indirect RAM from A with borrow 0x96 - 0x97 1 2 SUBB A,#data Subtract immediate data from A with borrow 0x94 2 2 INC A Increment accumulator 0x04 1 1 INC Rn Increment register 0x08 - 0x 0F 1 2 INC direct Increment direct byte 0x05 2 3 INC @Ri Increment indirect RAM 0x06 - 0x07 1 3 INC DPTR Increment data pointer 0xA3 1 1 DEC A Decrement accumulator 0x14 1 1 DEC Rn Decrement register 0x8 - 0x1F 1 2 DEC direct Decrement direct byte 0x15 2 3 DEC @Ri Decrement indirect RAM 0x16 - 0x17 1 3 MUL AB Multiply A and B 0xA4 1 5 DIV Divide A by B 0x84 1 5 DA A Decimal adjust accumulator 0xD4 1 1 ANL A,Rn AND register to accumulator 0x58 - 0x5F 1 1 ANL A,direct AND direct byte to accumulator 0x55 2 2 ANL A,@Ri AND indirect RAM to accumulator 0x56 - 0x57 1 2 ANL A,#data AND immediate data to accumulator 0x54 2 2 ANL direct,A AND accumulator to direct byte 0x52 2 3 ANL direct,#data AND immediate data to direct byte 0x53 3 4 ORL A,Rn OR register to accumulator 0x48 - 0x4F 1 1 ORL A,direct OR direct byte to accumulator 0x45 2 2 ORL A,@Ri OR indirect RAM to accumulator 0x46 - 0x47 1 2 ORL A,#data OR immediate data to accumulator 0x44 2 2 ORL direct,A OR accumulator to direct byte 0x42 2 3 ORL direct,#data OR immediate data to direct byte 0x43 3 4 XRL A,Rn Exclusive OR register to accumulator 0x68 - 0x6F 1 1 XRL A,direct Exclusive OR direct byte to accumulator 0x65 2 2 XRL A,@Ri Exclusive OR indirect RAM to accumulator 0x66 - 0x67 1 2 XRL A,#data Exclusive OR immediate data to accumulator 0x64 2 2 XRL direct,A Exclusive OR accumulator to direct byte 0x62 2 3 Arithmetic Operations Logical Operations SWRS033G Page 57 of 244 CC1110Fx / CC1111Fx Mnemonic Description Hex Opcode Bytes Cycles XRL direct,#data Exclusive OR immediate data to direct byte 0x63 3 4 CLR A Clear accumulator 0xE4 1 1 CPL A Complement accumulator 0xF4 1 1 RL A Rotate accumulator left 0x23 1 1 RLC A Rotate accumulator left through carry 0x33 1 1 RR A Rotate accumulator right 0x03 1 1 RRC A Rotate accumulator right through carry 0x13 1 1 SWAP A Swap nibbles within the accumulator 0xC4 1 1 MOV A,Rn Move register to accumulator 0xE8 - 0xEF 1 1 MOV A,direct Move direct byte to accumulator 0xE5 2 2 MOV A,@Ri Move indirect RAM to accumulator 0xE6 - 0xE7 1 2 MOV A,#data Move immediate data to accumulator 0x74 2 2 MOV Rn,A Move accumulator to register 0xF8 - 0xFF 1 2 MOV Rn,direct Move direct byte to register 0xA8 - 0xAF 2 4 MOV Rn,#data Move immediate data to register 0x78 - 0x7F 2 2 MOV direct,A Move accumulator to direct byte 0xF5 2 3 MOV direct,Rn Move register to direct byte 0x88 - 0x8F 2 3 MOV direct1,direct2 Move direct byte to direct byte 0x85 3 4 MOV direct,@Ri Move indirect RAM to direct byte 0x86 - 0x87 2 4 MOV direct,#data Move immediate data to direct byte 0x75 3 3 MOV @Ri,A Move accumulator to indirect RAM 0xF6 - 0xF7 1 3 MOV @Ri,direct Move direct byte to indirect RAM 0xA6 - 0xA7 2 5 MOV @Ri,#data Move immediate data to indirect RAM 0x76 - 0x77 2 3 MOV DPTR,#data16 Load data pointer with a 16-bit constant 0x90 3 3 MOVC A,@A+DPTR Move code byte relative to DPTR to accumulator 0x93 1 3 MOVC A,@A+PC Move code byte relative to PC to accumulator 0x83 1 3 MOVX A,@Ri Move external RAM (8-bit address) to A 0xE2 - 0xE3 1 3 - 10 MOVX A,@DPTR Move external RAM (16-bit address) to A 0xE0 1 3 - 10 MOVX @Ri,A Move A to external RAM (8-bit address) 0xF2 - 0xF3 1 4 - 11 MOVX @DPTR,A Move A to external RAM (16-bit address) 0xF0 1 4 - 11 PUSH direct Push direct byte onto stack 0xC0 2 4 POP direct Pop direct byte from stack 0xD0 2 3 XCH A,Rn Exchange register with accumulator 0xC8 - 0xCF 1 2 XCH A,direct Exchange direct byte with accumulator 0xC5 2 3 XCH A,@Ri Exchange indirect RAM with accumulator 0xC6 - 0xC7 1 3 XCHD A,@Ri Exchange low-order nibble indirect. RAM with A 0xD6 - 0xD7 1 3 Data Transfers SWRS033G Page 58 of 244 CC1110Fx / CC1111Fx Mnemonic Description Hex Opcode Bytes Cycles ACALL addr11 Absolute subroutine call xxx119 2 6 LCALL addr16 Long subroutine call 0x12 3 6 RET Return from subroutine 0x22 1 4 RETI Return from interrupt 0x32 1 4 Program Branching 9 AJMP addr11 Absolute jump xxx01 2 3 LJMP addr16 Long jump 0x02 3 4 SJMP rel Short jump (relative address) 0x80 2 3 JMP @A+DPTR Jump indirect relative to the DPTR 0x73 1 2 JZ rel Jump if accumulator is zero 0x60 2 3 JNZ rel Jump if accumulator is not zero 0x70 2 3 JC rel Jump if carry flag is set to 1 0x40 2 3 JNC Jump if carry flag is 0 0x50 2 3 JB bit,rel Jump if direct bit is set to 1 0x20 3 4 JNB bit,rel Jump if direct bit is 0 0x30 3 4 JBC bit,direct rel Jump if direct bit is set to 1 and clear the bit to 0 0x10 3 4 CJNE A,direct rel Compare direct byte to A and jump if not equal 0xB5 3 4 CJNE A,#data rel Compare immediate to A and jump if not equal 0xB4 3 4 CJNE Rn,#data rel Compare immediate to reg. and jump if not equal 0xB8 - 0xBF 3 4 CJNE @Ri,#data rel Compare immediate to indirect and jump if not equal 0xB6 -0xB7 3 4 DJNZ Rn,rel Decrement register and jump if not zero 0xD8 - 0xDF 2 3 DJNZ direct,rel Decrement direct byte and jump if not zero 0xD5 3 4 NOP No operation 0x00 1 1 Boolean Variable Operations CLR C Clear carry flag 0xC3 1 1 CLR bit Clear direct bit 0xC2 2 3 SETB C Set carry flag to 1 0xD3 1 1 SETB bit Set direct bit to 1 0xD2 2 3 CPL C Complement carry flag 0xB3 1 1 CPL bit Complement direct bit 0xB2 2 3 ANL C,bit AND direct bit to carry flag 0x82 2 2 ANL C,/bit AND complement of direct bit to carry 0xB0 2 2 ORL C,bit OR direct bit to carry flag 0x72 2 2 ORL C,/bit OR complement of direct bit to carry 0xA0 2 2 MOV C,bit Move direct bit to carry flag 0xA2 2 2 MOV bit,C Move carry flag to direct bit 0x92 2 3 Set SW breakpoint in debug mode 0xA5 1 1 Miscellaneous TRAP Table 37: Instruction Set Summary 9 addr11[10:8] is mapped into bits 7:5 of the first instruction byte (i.e. the opcode). addr11[7:0] is mapped into the second instruction byte SWRS033G Page 59 of 244 CC1110Fx / CC1111Fx Instruction CY OV AC ADD x x x ADDC x x x SUBB x x x MUL 0 x - DIV 0 x - DA x - - RRC x - - RLC x - - SETB C 1 - - CLR C x - - CPL C x - - ANL C,bit x - - ANL C,/bit x - - ORL C,bit x - - ORL C,/bit x - - MOV C,bit x - - CJNE x - - "0" = Clear to 0, "1" = Set to 1, "x" = Set to 1/Clear to 0, "-" = Not affected Table 38: Instructions that Affect Flag Settings 10.5 Interrupts The CPU has 18 interrupt sources. Each source has its own request flag located in a set of Interrupt Flag SFRs. Each interrupt can be individually enabled or disabled. The definitions of the interrupt sources and the interrupt vectors are given in Table 39. 2 I S and USART1 share interrupts. On the CC1111Fx USB shares interrupt with Port 2 2 inputs. The interrupt aliases for I S and USB are listed in Table 40. However, in the following sections the original interrupt names, masks, and flags listed in Table 39 are the ones used. The interrupts are grouped into a set of priority level groups with selectable priority levels. Note that some peripherals have several events that can generate the interrupt request associated with that peripheral. This applies to P0, P1, P2, DMA, Timer 1, Timer 2, Timer 3, Timer 4, and Radio. These peripherals have interrupt mask bits for each internal interrupt source in the corresponding SFRs. Note that 2 I S has its own interrupt enable bits even if it has only one event per interrupt. For the peripherals that have their own mask bits, one or more of these bits must be set for the associated CPU interrupt flag to be asserted. In order to use any of the interrupts in the CC1110Fx/CC1111Fx the following steps must be taken: The interrupt enable registers are described in Section 10.5.1 and the interrupt priority settings are described in Section 10.5.3 on Page 68. 10.5.1 Interrupt Masking Each interrupt can be individually enabled or disabled by the interrupt enable bits in the Interrupt Enable SFRs IEN0, IEN1, and IEN2. The Interrupt Enable SFRs are described below and summarized in Table 39. SWRS033G 1. Clear interrupt 10.5.2) flags (see Section 2. Set individual interrupt enable bit in the peripherals SFR, if any 3. Set the corresponding individual, interrupt enable bit in the IEN0, IEN1, or IEN2 registers to 1 4. Enable global interrupt by setting the IEN0.EA = 1 Page 60 of 244 CC1110Fx / CC1111Fx 5. Begin the interrupt service routine at the corresponding vector address of that interrupt. See Table 39 for addresses Note: An interrupt must not be enabled without having proper code located at the corresponding interrupt vector address Interrupt Number Description Interrupt Name Interrupt Vector CPU Interrupt Mask CPU Interrupt Flag 0 RF TX done / RX ready RFTXRX 0x03 IEN0.RFTXRXIE TCON.RFTXRXIF10 1 ADC end of conversion ADC 0x0B IEN0.ADCIE TCON.ADCIF10 2 USART0 RX complete URX0 0x13 IEN0.URX0IE TCON.URX0IF10 3 USART1 RX complete URX1 0x1B IEN0.URX1IE TCON.URX1IF10 2 (Note: I S RX complete, see Table 40) 4 AES encryption/decryption complete ENC 0x23 IEN0.ENCIE S0CON.ENCIF 5 Sleep Timer compare ST 0x2B IEN0.STIE IRCON.STIF11 6 Port 2 inputs P2INT 0x33 IEN2.P2IE IRCON2.P2IF11 (Note: Also used for USB on CC1111Fx,, see Table 40) 7 USART0 TX complete UTX0 0x3B IEN2.UTX0IE IRCON2.UTX0IF 8 DMA transfer complete DMA 0x43 IEN1.DMAIE IRCON.DMAIF 9 Timer 1 (16-bit) capture/Compare/overflow T1 0x4B IEN1.T1IE IRCON.T1IF10,11 10 Timer 2 (MAC Timer) overflow T2 0x53 IEN1.T2IE IRCON.T2IF10, 11 11 Timer 3 (8-bit) compare/overflow T3 0x5B IEN1.T3IE IRCON.T3IF10, 11 12 Timer 4 (8-bit) compare/overflow T4 0x63 IEN1.T4IE IRCON.T4IF10, 11 13 Port 0 inputs P0INT 0x6B IEN1.P0IE IRCON.P0IF11 UTX1 0x73 IEN2.UTX1IE IRCON2.UTX1IF (Note: P0_7 interrupt used for USB Resume interrupt on CC1111Fx) 14 USART1 TX complete 2 (Note: I S TX complete, see Table 40) 15 Port 1 inputs P1INT 0x7B IEN2.P1IE IRCON2.P1IF11 16 RF general interrupts RF 0x83 IEN2.RFIE S1CON.RFIF11 17 Watchdog overflow in timer mode WDT 0x8B IEN2.WDTIE IRCON2.WDTIF Table 39: Interrupts Overview 10 Cleared by HW when the CPU vectors to the ISR 11 Additional interrupt mask bits and/or interrupt flags found in the peripheral's SFRs SWRS033G Page 61 of 244 CC1110Fx / CC1111Fx Interrupt Number Description Interrupt Name Interrupt Vector CPU Interrupt Mask Alias CPU Interrupt Flag Alias 3 I2S RX complete URX1/ I2SRX 0x1Bh IEN0.I2SRXIE TCON.I2SRXIF12 6 USB Interrupt pending (CC1111Fx ) P2INT/ USB 0x33h IEN2.USBIE IRCON2.USBIF13 13 USB resume interrupt (CC1111Fx ). P0INT 0x6B IEN1.P0IE IRCON.P0IF UTX1/ I2STX 0x73h IEN2.I2STXIE IRCON2.I2STXIF12 P0_6 and P0_7 does not exist on CC1110Fx. USB resume interrupt configured like P0_7 interrupt on CC1110Fx I2S TX complete 14 2 Table 40: Shared Interrupt Vectors (I S and USB) 12 The I S module has its own interrupt enable bits and interrupt flags (no masking) 2 13 Additional interrupt mask bits and interrupt flags found in the peripheral's SFRs IEN0 (0xA8) - Interrupt Enable 0 Register Bit Field Name Reset R/W Description 7 EA 0 R/W Enable All 6 5 4 3 2 1 0 STIE ENCIE URX1IE / I2SRXIE URX0IE ADCIE RFTXRXIE 0 No interrupt will be acknowledged 1 Each interrupt source is individually enabled or disabled by setting its corresponding enable bit 0 R/W Not used 0 R/W Sleep Timer interrupt enable 0 0 0 0 0 R/W R/W R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled AES encryption/decryption interrupt enable 0 Interrupt disabled 1 Interrupt enabled USART1 RX interrupt enable / I2S RX interrupt enable 0 Interrupt disabled 1 Interrupt enabled USART0 RX interrupt enable 0 Interrupt disabled 1 Interrupt enabled ADC interrupt enable 0 Interrupt disabled 1 Interrupt enabled RF TX/RX done interrupt enable 0 Interrupt disabled 1 Interrupt enabled SWRS033G Page 62 of 244 CC1110Fx / CC1111Fx IEN1 (0xB8) - Interrupt Enable 1 Register Bit Reset R/W Description 7 0 R/W Not used 6 0 R0 Not used 0 R/W Port 0 interrupt enable 5 Field Name P0IE 0 Interrupt disabled 1 Interrupt enabled 4 T4IE 0 R/W Timer 4 interrupt enable 0 Interrupt disabled 1 Interrupt enabled 3 T3IE 0 R/W Timer 3 interrupt enable 0 Interrupt disabled 1 Interrupt enabled 2 T2IE 0 R/W Timer 2 interrupt enable 0 Interrupt disabled 1 Interrupt enabled 1 T1IE 0 R/W Timer 1 interrupt enable 0 Interrupt disabled 1 Interrupt enabled 0 DMAIE 0 R/W DMA transfer interrupt enable 0 Interrupt disabled 1 Interrupt enabled SWRS033G Page 63 of 244 CC1110Fx / CC1111Fx IEN2 (0x9A) - Interrupt Enable 2 Register Bit Field Name 7:6 5 4 3 2 1 0 10.5.2 WDTIE P1IE UTX1IE / I2STXIE UTX0IE P2IE / USBIE RFIE Reset R/W Description 0 R/W Not used 0 R/W Watchdog timer interrupt enable 0 0 0 0 0 R/W R/W R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Port 1 interrupt enable 0 Interrupt disabled 1 Interrupt enabled USART1 TX interrupt enable / I2S TX interrupt enable 0 Interrupt disabled 1 Interrupt enabled USART0 TX interrupt enable 0 Interrupt disabled 1 Interrupt enabled Port 2 interrupt enable (Also used for USB interrupt enable on CC1111Fx) 0 Interrupt disabled 1 Interrupt enabled RF general interrupt enable 0 Interrupt disabled 1 Interrupt enabled Interrupt Processing When an interrupt occurs, the CPU will vector to the interrupt vector address shown in Table 39, if this particular interrupt has been enabled. Once an interrupt service has begun, it can be interrupted only by a higher priority interrupt. The interrupt service is terminated by a RETI (return from interrupt) instruction. When a RETI is performed, the CPU will return to the instruction that would have been next when the interrupt occurred. When the interrupt condition occurs, an interrupt flag bit will be set in one of the CPU interrupt flag registers and in the peripherals interrupt flag register, if this is available. These bits are asserted regardless of whether the interrupt is enabled or disabled. If the interrupt is enabled when an interrupt flag is asserted, then on the next instruction cycle the interrupt will be acknowledged by hardware forcing an LCALL to the appropriate vector address. Interrupt response will require a varying amount of time depending on the state of the CPU when the interrupt occurs. If the CPU is performing an interrupt service with equal or greater priority, the new interrupt will be pending until it becomes the interrupt with highest priority. In other cases, the response time depends on the current instruction. The fastest possible response to an interrupt is seven instruction cycles. This includes one machine cycle for detecting the interrupt and six cycles to perform the LCALL. Clearing interrupt flags must be done correctly to ensure that no interrupts are lost or processed more than once. For pulsed or edge shaped interrupt sources one should clear the CPU interrupt flag prior to clearing the module interrupt flag, if available, for flags that are not automatically cleared. For level triggered interrupts (port interrupts) one has to clear the module interrupt flag prior to clearing the CPU interrupt flag. When handling interrupts where the CPU interrupt flag is cleared by hardware, the software should only clear the module interrupt flag. The following interrupts are cleared by hardware: RFTXRX T1 ADC T2 URX0 T3 URX1/I2SRX T4 One or more module flags can be cleared at once. However the safest approach is to only handle one interrupt source each time the interrupt is triggered, hence clearing only one SWRS033G Page 64 of 244 CC1110Fx / CC1111Fx module flag. When any module flag is cleared the chip will check if there are any module interrupt flags left that are both enabled and asserted, if so the CPU interrupt flag will be asserted and a new interrupt triggered. The following code example shows how only one module flag is handled and cleared each time the interrupt occurs: #pragma vector = RF_VECTOR __interrupt void rf_interrupt (void) { S1CON &= ~0x03; // Clear CPU interrupt flag if(RFIF & 0x80) // TX underflow { irq_txunf(); // Handle TX underflow RFIF &= ~0x80; // Clear module interrupt flag } else if(RFIF & 0x40) // RX overflow { irq_rxovf(); // Handle RX overflow RFIF &= ~0x40; // Clear module interrupt flag } // Use "else if" to check and handle other RFIF flags } TCON (0x88) - CPU Interrupt Flag 1 Bit Field Name Reset R/W Description 7 URX1IF / I2SRXIF 0 R/W H0 USART1 RX interrupt flag / I2S RX interrupt flag 6 5 ADCIF 4 3 URX0IF 2 1 0 RFTXRXIF Set to 1 when USART1 RX interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 0 R/W Not used 0 R/W H0 ADC interrupt flag. Set to 1 when ADC interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 0 R/W Not used 0 R/W H0 USART0 RX interrupt flag. Set to 1 when USART0 interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 1 R/W Reserved. Must always be set to 1. 0 R/W H0 RF TX/RX complete interrupt flag. Set to 1 when RFTXRX interrupt occurs and cleared when CPU vectors to the interrupt service routine. 1 R/W 0 Interrupt not pending 1 Interrupt pending Reserved. Must always be set to 1. SWRS033G Page 65 of 244 CC1110Fx / CC1111Fx S0CON (0x98) - CPU Interrupt Flag 2 Bit Field Name 7:2 1 0 ENCIF_1 ENCIF_0 Reset R/W Description 0 R/W Not used 0 R/W AES interrupt. ENCIF has two interrupt flags, ENCIF_1 and ENCIF_0. Interrupt source sets both ENCIF_1 and ENCIF_0, but setting one of these flags in SW will generate an interrupt request. Both flags are set when the AES co-processor requests the interrupt. 0 R/W 0 Interrupt not pending 1 Interrupt pending AES interrupt. ENCIF has two interrupt flags, ENCIF_1 and ENCIF_0. Interrupt source sets both ENCIF_1 and ENCIF_0, but setting one of these flags in SW will generate an interrupt request. Both flags are set when the AES co-processor requests the interrupt. 0 Interrupt not pending 1 Interrupt pending S1CON (0x9B) - CPU Interrupt Flag 3 Bit Field Name 7:6 1 0 RFIF_1 RFIF_0 Reset R/W Description 0 R/W Not used 0 R/W RF general interrupt. RFIF has two interrupt flags, RFIF_1 and RFIF_0. Interrupt source sets both RFIF_1 and RFIF_0, but setting one of these flags in SW will generate an interrupt request. Both flags are set when the radio requests the interrupt. 0 R/W 0 Interrupt not pending 1 Interrupt pending RF general interrupt. RFIF has two interrupt flags, RFIF_1 and RFIF_0. Interrupt source sets both RFIF_1 and RFIF_0, but setting one of these flags in SW will generate an interrupt request. Both flags are set when the radio requests the interrupt. 0 Interrupt not pending 1 Interrupt pending SWRS033G Page 66 of 244 CC1110Fx / CC1111Fx IRCON (0xC0) - CPU Interrupt Flag 4 Bit Field Name Reset R/W Description 7 STIF 0 R/W Sleep Timer interrupt flag 0 Interrupt not pending 1 Interrupt pending 6 5 P0IF 0 R/W Reserved. Must always be set to 0. Failure to do so will lead to ISR toggling (interrupt routine sustained) 0 R/W Port 0 interrupt flag 0 Interrupt not pending 1 Interrupt pending 4 T4IF 0 R/W H0 Timer 4 interrupt flag. Set to 1 when Timer 4 interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 3 T3IF 0 R/W H0 Timer 3 interrupt flag. Set to 1 when Timer 3 interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 2 T2IF 0 R/W H0 Timer 2 interrupt flag. Set to 1 when Timer 2 interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 1 T1IF 0 R/W H0 Timer 1 interrupt flag. Set to 1 when Timer 1 interrupt occurs and cleared when CPU vectors to the interrupt service routine. 0 Interrupt not pending 1 Interrupt pending 0 DMAIF 0 R/W DMA complete interrupt flag. 0 Interrupt not pending 1 Interrupt pending SWRS033G Page 67 of 244 CC1110Fx / CC1111Fx IRCON2 (0xE8) - CPU Interrupt Flag 5 Bit Field Name 7:5 4 3 2 1 0 10.5.3 WDTIF P1IF UTX1IF / I2STXIF UTX0IF P2IF / USBIF Reset R/W Description 0 R/W Not used 0 R/W Watchdog timer interrupt flag 0 R/W 0 R/W 0 R/W 0 R/W 0 Interrupt not pending 1 Interrupt pending Port 1 interrupt flag. 0 Interrupt not pending 1 Interrupt pending USART1 TX interrupt flag / I2S TX interrupt flag 0 Interrupt not pending 1 Interrupt pending USART0 TX interrupt flag 0 Interrupt not pending 1 Interrupt pending Port2 interrupt flag / USB interrupt flag 0 Interrupt not pending 1 Interrupt pending Interrupt Priority The interrupts are grouped into six interrupt priority groups and the priority for each group is set by the registers IP0 and IP1. The interrupt priority groups with assigned interrupt sources are shown in Table 42. Each group is assigned one of four priority levels, and by default all six interrupt priority groups are assign the lowest priority. In order to assign a higher priority to an interrupt, i.e. to its interrupt group, the corresponding bits in IP0 and IP1 must be set as shown in Table 41 on Page 69. While an interrupt service request is in progress, it cannot be interrupted by a lower or same level interrupt. In the case when interrupt requests of the same priority level are received simultaneously, the polling sequence shown in Table 43 is used to resolve the priority of each requests. IP1 (0xB9) - Interrupt Priority 1 Bit Field Name 7:6 Reset R/W Description 0 R/W Not used 5 IP1_IPG5 0 R/W Interrupt group 5, priority control bit 1, refer to Table 41 4 IP1_IPG4 0 R/W Interrupt group 4, priority control bit 1, refer to Table 41 3 IP1_IPG3 0 R/W Interrupt group 3, priority control bit 1, refer to Table 41 2 IP1_IPG2 0 R/W Interrupt group 2, priority control bit 1, refer to Table 41 1 IP1_IPG1 0 R/W Interrupt group 1, priority control bit 1, refer to Table 41 0 IP1_IPG0 0 R/W Interrupt group 0, priority control bit 1, refer to Table 41 SWRS033G Page 68 of 244 CC1110Fx / CC1111Fx IP0 (0xA9) - Interrupt Priority 0 Bit Field Name 7:6 Reset R/W Description 0 R/W Not used 5 IP0_IPG5 0 R/W Interrupt group 5, priority control bit 0, refer to Table 41 4 IP0_IPG4 0 R/W Interrupt group 4, priority control bit 0, refer to Table 41 3 IP0_IPG3 0 R/W Interrupt group 3, priority control bit 0, refer to Table 41 2 IP0_IPG2 0 R/W Interrupt group 2, priority control bit 0, refer to Table 41 1 IP0_IPG1 0 R/W Interrupt group 1, priority control bit 0, refer to Table 41 0 IP0_IPG0 0 R/W Interrupt group 0, priority control bit 0, refer to Table 41 IP1_x IP0_x Priority Level 0 0 0 (lowest) 0 1 1 1 0 2 1 1 3 (highest) Table 41: Priority Level Setting Group Interrupts IPG0 RFTXRX RF DMA IPG1 ADC T1 P2INT / USB IPG2 URX0 T2 UTX0 IPG3 URX1 / I2SRX T3 UTX1 / I2STX IPG4 ENC T4 P1INT IPG5 ST P0INT (USB Resume) WDT Table 42: Interrupt Priority Groups SWRS033G Page 69 of 244 CC1110Fx / CC1111Fx Interrupt Number Interrupt Name 0 RFTXRX 16 RF 8 DMA 1 ADC 9 T1 2 URX0 10 T2 3 URX1 / I2SRX 11 T3 4 ENC 12 T4 5 ST 13 P0INT / (USB Resume) 6 P2INT / USB 7 UTX0 14 URX1 / I2STX 15 P1INT 17 WDT Polling sequence Table 43: Interrupt Polling Sequence 11 Debug Interface The CC1110Fx/CC1111Fx includes an on-chip debug module which communicates over a two-wire interface. The debug interface allows programming of the on-chip flash. It also provides access to memory and registers contents, and debug features such as breakpoints, single-stepping, and register modification. The debug interface uses the I/O pins P2_1 as Debug Data and P2_2 as Debug Clock during Debug mode. These I/O pins can be used as general purpose I/O only while the device is not in Debug mode. Thus the debug interface does not interfere with any peripheral I/O pins. 11.1 Debug Mode Debug mode is entered by forcing two rising edge transitions on pin P2_2 (Debug Clock) while the RESET_N input is held low. Note: Debugging of PM2 and PM3 is not supported. Also note that CLKCON.CLKSPD must be 000 or 001 when using the debug interface While in Debug mode pin P2_1 is the Debug Data bi-directional pin and P2_2 is the Debug Clock input pin. 11.2 Debug Communication The debug interface uses an SPI-like two-wire interface consisting of the P2_1 (Debug Data) and P2_2 (Debug Clock) pins. Data is driven on the bi-directional Debug Data pin at the positive edge of Debug Clock and data is sampled on the negative edge of this clock. Debug commands are sent by an external host and consist of 1 to 4 output bytes (including command byte) from the host and an optional input byte read by the host. Command and data is transferred with MSB first. Figure 17 shows a timing diagram of data on the debug interface. SWRS033G Page 70 of 244 CC1110Fx / CC1111Fx Figure 17: Debug Interface Timing Diagram 11.3 Debug Lock Bit For software and/or access protection, a set of lock bits can be written. This information is contained in the Flash Information Page (see Section 10.2.3.2), at location 0x000. The Flash Information Page can only be accessed through the debug interface. There are three kinds of lock protect bits as described in this section. The lock size bits LSIZE[2:0] are used to define which section of the flash memory should be write protected, if any. The size of the write protected area can be set to 0 (no pages), 1, 2, 4, 8, 16, 24, or 32 KB (all pages), starting from top of flash memory and defining a section below this. Note that for CC1110F8, CC1111F8, CC1110F16, and CC1111F16, the only supported value for LSIZE[2:0]is 0 and 7 (all or no pages respectively). The second type of lock protect bits is BBLOCK, which is used to lock the boot sector page (page 0 ranging from address 0x0000 to 0x03FF). When BBLOCK is set to 0, the boot sector page is locked. The third type of lock protect bit is DBGLOCK, which is used to disable hardware debug support through the Debug Interface. When DBGLOCK is set to 0, almost all debug commands are disabled. When the Debug Lock bit, DBGLOCK, is set to 0 (see Table 44) all debug commands except CHIP_ERASE, READ_STATUS and GET_CHIP_ID are disabled and will not function. The status of the Debug Lock bit can be read using the READ_STATUS command (see Section 11.4.2). Note that after the Debug Lock bit has changed due to a Flash Information Page write or a flash mass erase, a HALT, RESUME, DEBUG_INSTR, STEP_INSTR, or STEP_REPLACE command must be executed so that the Debug Lock value returned by READ_STATUS shows the updated Debug Lock value. For example a dummy NOP DEBUG_INSTR command could be executed. The Debug Lock bit will also be updated after a device reset so an alternative is to reset the chip and reenter debug mode. The CHIP_ERASE command will set all bits in flash memory to 1. This means that after issuing a CHIP_ERASE command the boot sector will be writable, no pages will be writeprotected, and all debug commands are enabled. The lock protect bits are written as a normal flash write to FWDATA (see Section 12.3.2), but the Debug Interface needs to select the Flash Information Page first instead of the Flash Main Page which is the default setting. The Information Page is selected through the Debug Configuration which is written through the Debug Interface only. Refer to Section 11.4.1 and Table 46 for details on how the Flash Information Page is selected using the Debug Interface. Table 44 defines the byte containing the flash lock protection bits. Note that this is not an SFR, but instead the byte stored at location 0x000 in Flash Information Page. SWRS033G Page 71 of 244 CC1110Fx / CC1111Fx Bit Field Name 7:5 4 3:1 0 Description Reserved, write as 0 BBLOCK LSIZE[2:0] DBGLOCK Boot Block Lock 0 Page 0 is write protected 1 Page 0 is writeable, unless LSIZE is 000 Lock Size. Sets the size of the upper flash area which is write-protected. Byte sizes are listed below 000 32 KB (all pages) 001 24 KB CC1110F32 and CC1111F32 only 010 16 KB CC1110F32 and CC1111F32 only 011 8 KB CC1110F32 and CC1111F32 only 100 4 KB CC1110F32 and CC1111F32 only 101 2 KB CC1110F32 and CC1111F32 only 110 1 KB CC1110F32 and CC1111F32 only 111 0 bytes (no pages) Debug lock bit 0 Disable debug commands 1 Enable debug commands Table 44: Flash Lock Protection Bits Definition 11.4 Debug Commands The debug commands are shown in Table 45. Some of the debug commands are described in further detail in the following sections 11.4.1 Debug Configuration The commands WR_CONFIG and RD_CONFIG are used to access the debug configuration data byte. The format and description of this configuration data is shown in Table 46 11.4.2 Debug Status A debug status byte is read using the READ_STATUS command. The format and description of this debug status is shown in Table 47. CC1110Fx/CC1111Fx supports up to four hardware breakpoints. When a hardware breakpoint is enabled it will compare the CPU address bus with the breakpoint. When a match occurs, the CPU is halted. When issuing the SET_HW_BRKPNT debug command, the external host must supply three data bytes that define the hardware breakpoint. The hardware breakpoint itself consists of 18 bits while three bits are used for control purposes. The format of the three data bytes for the SET_HW_BRKPNT command is as follows. The first data byte consists of the following: The READ_STATUS command is used e.g. for polling the status of flash chip erase after a CHIP_ERASE command or oscillator stable status required for debug commands HALT, RESUME, DEBUG_INSTR, STEP_REPLACE, and STEP_INSTR. Bit Description 7:5 Unused 4:3 Breakpoint number; 0 - 3 2 Breakpoint enable 1:0 11.4.3 0 Disable 1 Enable Reserved. Must be 00. Hardware Breakpoints The debug command SET_HW_BRKPNT is used to set a hardware breakpoint. The The second data byte consists of bits 15 - 8 of the hardware breakpoint while the third data byte consists of bits 7 - 0 of the hardware SWRS033G Page 72 of 244 CC1110Fx / CC1111Fx breakpoint. This means that the second and third data byte sets the CPU CODE address where the CPU is halted. 11.4.4 Flash Programming Programming of the on-chip flash is performed via the debug interface. The external host must initially send instructions using the DEBUG_INSTR debug command to perform the flash programming with the Flash Controller as described in Section 12.3. Command Instruction Code Description CHIP_ERASE 0001 0100 Perform flash chip erase (mass erase). The debug interface will be enabled and no parts of flash will be write-protected after issuing this command. Do not use any other commands than READ_STATUS until mass erase has completed. Return 1 status byte to host WR_CONFIG 0001 1101 Write configuration data. Return 1 status byte to host. Refer to Table 46 for details. RD_CONFIG 0010 0100 Read configuration data. Return value set by WR_CONFIG command GET_PC 0010 1000 Return value of 16-bit program counter READ_STATUS 0011 0100 Read status byte. Refer to Table 47 SET_HW_BRKPNT 0011 1011 Set hardware breakpoint HALT 0100 0100 Halt CPU operation. Return 1 status byte to host RESUME 0100 1100 Resume CPU operation. To run this command, the CPU must have been halted. Return 1 status byte to host DEBUG_INSTR 0101 01yy Run debug instruction. The supplied instruction will be executed by the CPU without incrementing the program counter. To run this command, the CPU must have been halted. Return 1 status byte to host. yy: Number of bytes in the CPU instruction (see Table 37). Valid values are 01, 10, and 11 STEP_INSTR 0101 1100 Step CPU instruction. The CPU will execute the next instruction from program memory and increment the program counter after execution. To run this command, the CPU must have been halted. Return 1 status byte to host STEP_REPLACE 0110 01 yy Step and replace CPU instruction. The supplied instruction will be executed by the CPU instead of the next instruction in program memory. The program counter will be incremented after execution. To run this command, the CPU must have been halted. Return 1 status byte to host. yy: Number of bytes in the CPU instruction (see Table 37). Valid values are 01, 10, and 11 GET_CHIP_ID 0110 1000 Return value of 16-bit chip ID (PARTNUM:VERSION). Table 45: Debug Commands SWRS033G Page 73 of 244 CC1110Fx / CC1111Fx Bit Field Name Description 7:4 3 2 1 0 Not used. Must be set to 0000 TIMERS_OFF Disable timer operation (Timer 1/2/3/4). This overrides the TIMER_SUSPEND bit and its function. DMA_PAUSE 0 Do not disable timers 1 Disable timers DMA pause TIMER_SUSPEND 0 Enable DMA transfers 1 Pause all DMA transfers Suspend timers (Timer 1/2/3/4). Timer operation is suspended for debug instructions and if a step instruction is a branch. If not suspended, these instructions would result an extra timer count during the clock cycle in which the branch is executed SEL_FLASH_INFO_PAGE 0 Do not suspend timers 1 Suspend timers Select Flash Information Page in order to write flash lock bits (1 KB lowest part of flash) 0 Select flash Main Page 1 Select Flash Information Page Table 46: Debug Configuration SWRS033G Page 74 of 244 CC1110Fx / CC1111Fx Bit Field Name Description 7 CHIP_ERASE_DONE Flash chip erase done 6 5 4 3 2 1 0 PCON_IDLE CPU_HALTED POWER_MODE_0 HALT_STATUS DEBUG_LOCKED OSCILLATOR_STABLE STACK_OVERFLOW 0 Chip erase in progress 1 Chip erase done PCON idle 0 CPU is running 1 CPU is idle (clock gated) CPU halted 0 CPU running 1 CPU halted Power Mode 0 0 Power Mode 1 - 3 selected 1 Power Mode 0 selected (active mode if the CPU is running) Halt status. Returns cause of last CPU halt 0 CPU was halted by HALT debug command 1 CPU was halted by software or hardware breakpoint Debug locked. Returns value of DBGLOCK bit 0 Debug interface is not locked 1 Debug interface is locked Oscillators stable. This bit represents the status of the SLEEP.XSOC_STB and SLEEP.HFRC_STB register bits. 0 Oscillators not stable 1 Oscillators stable Stack overflow. This bit indicates when the CPU writes to DATA memory space at address 0xFF, which is possibly a stack overflow 0 No stack overflow 1 Stack overflow Table 47: Debug Status SWRS033G Page 75 of 244 CC1110Fx / CC1111Fx 12 Peripherals In the following sub-sections, each CC1110Fx/CC1111Fx peripheral is described in detail. 12.1 Power Management and Clocks This section describes the Power Management Controller. The Power Management Controller controls the use of active mode, power modes, and clock control. 12.1.1 (leakage) power consumption and also by using clock gating and turning off oscillators to reduce dynamic power consumption. The CC1110Fx/CC1111Fx has one active mode and four power modes, called PM0, PM1, PM2 and PM3, where PM3 has the lowest power consumption. Please note the minimum requirement on high speed crystal oscillator power down time in all modes of operation for CC1110Fx, see Table 11. The different operating modes are shown in Table 48. Power Management Introduction The CC1110Fx/CC1111Fx uses different operating modes to allow low-power operation. Ultra-lowpower operation is obtained by turning off power supply to modules to avoid static Operating Mode High-speed Oscillator Low-speed Oscillator Configuration A None A None B High speed XOSC B Low power RCOSC C HS RCOSC C 32.768 kHz XOSC Digital Voltage Regulator CPU Active B and / or C B or C On Running PM0 B and / or C B or C On Idle PM1 A B or C On Idle PM2 A B or C Off Idle PM3 A A Off Idle Table 48: Operating Modes Active mode: The full functional mode. The voltage regulator to the digital core is on and either the high speed RC oscillator or the high speed crystal oscillator or both are running. Either the Low power RC oscillator or the 32.768 kHz crystal oscillator is running. PM0: Same as active mode, but the CPU is idle, meaning that no code is being executed. PM1: The voltage regulator to the digital part is on. Neither the high speed crystal oscillator nor the high speed RC oscillator is running. Either the low power RC oscillator or the 32.768 kHz crystal oscillator is running. The system will go to active mode on reset or an external interrupt or when the Sleep Timer expires. PM2: The voltage regulator to the digital core is turned off. Neither the high speed crystal oscillator nor the high speed RC oscillator is running. Either the low power RC oscillator or the 32.768 kHz crystal oscillator is running. The system will go to active mode on reset or an external interrupt or when the Sleep Timer expires. The CC1111Fx will lose all USB state information when PM2 is entered. Thus, PM2 should not be used with USB. PM3: The voltage regulator to the digital core is turned off. None of the oscillators are running. The system will go to active mode on reset or an external interrupt. The CC1111Fx will lose all USB state information when PM3 is entered. Thus, PM3 should not be used with USB. When an external interrupt occurs in PM1, PM2, or PM3, or a Sleep Timer interrupt occur in PM1 and PM2, active mode will be entered and the code will start executing from where it entered PM1/2/(3). Any enabled interrupt will take the device from PM0 to active mode, and also in this case the code will start executing from where it entered PM0. A reset, however, will take the chip from any of the four power modes to active mode, but the code will start executing from the start of the program. SWRS033G Page 76 of 244 CC1110Fx / CC1111Fx 12.1.2 Active Mode and Power Modes 12.1.2.5 The different operating modes are described in detail in the five following sections. 12.1.2.1 Active Mode This is the full functional mode of operation where the CPU, peripherals, and RF transceiver are active. The voltage regulator to the digital core is on and either the high speed RC oscillator or the high speed crystal oscillator or both are running together with either the Low power RC oscillator or the 32.768 kHz crystal oscillator. 12.1.2.2 PM0 If the PCON.IDLE bit is set to 1 while in active mode, the CPU will be idle (clock gated) until any interrupt occur. All other peripherals will function as normal while the CPU is halted. 12.1.2.3 PM1 In PM1, the high speed oscillators (high speed XOSC and HS RCOSC) are powered down thereby halting the CPU and peripherals. The digital voltage regulator, the power-on reset, external interrupts, the low power RC oscillator or the 32.768 kHz crystal oscillator and Sleep Timer peripherals are active. I/O pins retain the I/O mode and output value set before entering PM1. When PM1 is entered, a power down sequence is run. PM1 is used when the expected time until a wakeup event is relatively short since PM1 uses a fast power down/up sequence. 12.1.2.4 PM2 PM2 has the second lowest power consumption. In PM2, the power-on reset, external interrupts, the low power RC oscillator or the 32.768 kHz crystal oscillator and Sleep Timer peripherals are active. I/O pins retain the I/O mode and output value set before entering PM2. The content of RAM and most registers is preserved in this mode (see Table 31, Table 32, and Table 33). All other internal circuits are powered down. When PM2 is entered, a power down sequence is run. PM2 is typically entered when using the Sleep Timer as the wakeup event. Please see Section 12.8.1 for minimum sleep time when using the Sleep Timer. PM3 In PM3 the internal voltage regulator and all oscillators are turned off. This power mode is used to achieve the operating mode with the lowest power consumption. In PM3 all internal circuits that are powered from internal voltage regulators are turned off. Reset (POR, or external) and external I/O port interrupts are the only functions that are operating in this mode. I/O pins retain the I/O mode and output value set before entering PM3. A reset or external interrupt condition will wake the device and make it enter active mode. The content of RAM and registers is preserved in this mode. PM3 uses the same power down/up sequence as PM2. PM3 is used to achieve ultra low power consumption when waiting for an external event. When entering active mode from PM1, PM2, or PM3, the high-speed oscillators, which where running when entering PM{1 - 3}, are started. If the high speed crystal oscillator is selected as source for the system clock (CLKCON.OSC=0), the system clock will use the HS RCOSC as clock source until the high speed crystal oscillator is stable (SLEEP.XOSC_STB=1). 12.1.3 Power Management Control The required power mode is selected by the SLEEP.MODE setting. Setting the IDLE bit in the PCON SFR after setting the MODE bits, makes the CC1111Fx/CC1111Fx enter the selected power mode. The following procedure must be followed to be able to safely put the device into one of the power modes PM{1 - 3}: // Pseudo Code SLEEP.MODE = PM{1-3} NOP(); NOP(); NOP(); If (SLEEP_MODE != 0) PCON.IDLE = 1; An interrupt from port pins or Sleep Timer (not PM3), or a power-on reset will wake the device and bring it into active mode by resetting the MODE bits and clear the IDLE bit. Since an interrupt can occur before the device has actually entered PM{1 - 3}, it is necessary to clear the MODE bits before returning from all ISRs associated with interrupts that can be SWRS033G Page 77 of 244 CC1110Fx / CC1111Fx used to wake the device from PM{1 - 3}. It should be noted that all port interrupts and Sleep Timer interrupt are blocked when SLEEP.MODE is different from 00, thus the time between setting SLEEP.MODE00 and asserting PCON.IDLE should be as short as possible. The SLEEP.MODE will be cleared to 00 by HW when power mode is entered, thus interrupts are enabled during power modes. All interrupts not to be used to wake up from power modes must be disabled before setting SLEEP.MODE00. It should be noted that after enabling the HS XOSC (CLKCON.OSC=0) one has to ensure that the HS XOSC is stable (SLEEP.XOSC_STB=1) before entering PM{1 - 3}. If the low power RCOSC is enabled (CLKCON.OSC32K=1) and the HS XOSC is selected as clock source for the system clock, the time between succeeding PM{1 - 3} modes (i.e. the time in active mode) must be larger than the startup time for the HS XOSC (see Table 11 and Table 12) plus the initial calibration time for the low power RCOSC (Table 14). 12.1.4 Power Management Registers This section describes the Power Management registers. All register bits retain their previous values when entering PM2 or PM3 unless otherwise stated. PCON (0x87) - Power Mode Control Bit Reset R/W Description 7:2 0 R/W Not used 1 0 R0/W1 Reserved. Must not be written to 1. Doing so will stop CPU from operating. 0 R0/W1 Power mode control. Writing a 1 to this bit forces CC1110Fx/CC1111Fx to enter the power mode set by SLEEP.MODE. This bit is always read as 0. 0 Field Name IDLE H0 All interrupt requests will clear this bit and CC1110Fx/CC1111Fx will reenter active mode. Note: see Section 12.1.3 for details on how this bit should be used. SWRS033G Page 78 of 244 CC1110Fx / CC1111Fx SLEEP (0xBE) - Sleep Mode Control Bit Field Name Reset R/W Description 7 USB_EN 0 R/W USB Enable (CC1111Fx). This bit is unused for CC1110Fx 0 Disable (Setting this bit to 0 will reset the USB controller) 1 Enable This bit will be 0 when returning from PM2 and PM3 6 5 4:3 2 XOSC_STB HFRC_STB RST[1:0] OSC_PD 0 0 XX 1 R R R R/W H0 1:0 MODE[1:0] 00 R/W High speed crystal oscillator (fXOSC) stable status 0 Oscillator is not powered up or not yet stable 1 Oscillator is powered up and stable High speed RC oscillator (HS RCOSC) stable status 0 Oscillator is not powered up or not yet stable 1 Oscillator is powered up and stable Status bit indicating the cause of the last reset. If there are multiple resets, the register will only contain the last event. 00 Power-on reset or Brown-out reset 01 External reset 10 Watchdog timer reset High speed XOSC and HS RCOSC power down setting. The bit is cleared if the CLKCON.OSC bit is toggled. If there is a calibration in progress (of the low power RC oscillator and/or the HS RC oscillator) and one attempts to set this bit, the oscillator not selected by the CLKCON.OSC bit will be powered down, and the bit will be set, at the end of calibration. 0 Both oscillators powered up 1 Oscillator not selected by CLKCON.OSC bit powered down Power mode setting 00 PM0 01 PM1 10 PM2 11 PM3 These bits will be set to 00 when entering PM{1 - 3} Note: It is necessary to clear the MODE bits before returning from all ISRs associated with interrupts that can be used to wake the device from PM{1 - 3}. See Section 12.1.3 for details 12.1.5 Oscillators and Clocks The CC1110Fx/CC1111Fx has one internal system clock. The source for the system clock can be either a high speed RC oscillator or a high speed crystal oscillator. The crystal oscillator for CC1110Fx operates at 26 - 27 MHz while the crystal oscillator for CC1111Fx operates at 48 MHz. The 26 - 27 MHz clock is used directly as the system clock for CC1110Fx. On CC1111Fx, the 48 MHz clock is used by the USB Controller only while a derived 24 MHz clock is used as the system clock. The source for the system clock is selected by the CLKCON.OSC bit. There is also one 32 kHz clock source that can either be a low power RCOSC or a 32.768 kHz crystal oscillator. This is controlled by the CLKCON.OSC32K bit. The choice of oscillator allows a trade-off between high-accuracy in the case of the crystal oscillator and low power consumption when the RC oscillator is used. Note that operation of the RF transceiver requires that the high speed crystal oscillator is used. SWRS033G Note: The high speed crystal oscillator must be stable (SLEEP.XOSC_STB=1) before using the radio. Page 79 of 244 CC1110Fx / CC1111Fx 12.1.5.1 High Speed Oscillators Two high speed oscillators are present in the device: High speed crystal oscillator (26 - 27 MHz for CC1110Fx and 48 MHz for CC1111Fx) High speed RC oscillator (13 - 13.5 MHz for CC1110Fx and 12 MHz for CC1111Fx) The high speed crystal oscillator startup time may be too long for some applications, and the device can therefore run on the high speed RCOSC until the crystal oscillator is stable. The HS RCOSC consumes less power than the crystal oscillator, but since it is not as accurate as the crystal oscillator it can not be used for RF transceiver operation. The CLKCON.OSC bit selects the source of the system clock (high speed crystal oscillator, HS XOSC, or high speed RC oscillator, HS RCOSC). The system clock will not change clock source before the selected clock source is stable (indicated by SLEEP.XOSC_STB and SLEEP.HFRC_STB). It should be noted that once the clock source change has been initiated the clock source should not be changed or updated again until the clock source change has taken place. When SLEEP.OSC_PD is 0, both oscillators are powered up and running. Be aware that SLEEP.OSC_PD is cleared if the CLKCON.OSC bit is toggled. A calibration of the HS RCOSC will be initiated by selecting the HS XOSC as system clock source (CLKCON.OSC is set to 0). The calibration will only be performed once. It is not possible to enter PM{1 - 3}, change system clock source back to HS RCOSC, or power down the HS RCOSC before the calibration is completed. Note that even if the calibration of the HS RCOSC is completed, a calibration of the low power RC oscillator might still be in progress and changing system clock source back to HS RCOSC will not be possible before also this calibration has completed. If SLEEP.OSC_PD=0, the HS RCOSC will run on the calibrated value once the calibration is completed (see Table 15 for initial calibration time). If SLEEP.OSC_PD=1, the HS RCOSC will be turned off after calibration, but the calibration value will be stored and used when the HS RCOSC is started again. In order to calibrate the HS RCOSC regularly (if so found necessary based on the drift parameters listed in Table 15) one should switch between using the HS RCOSC and the high speed crystal oscillator as system clock source. If CLKCON.OSC is set to 0 when entering PM{1 - 3}, the HS RCOSC will be calibrated once when returning to active mode. (the calibration will start once the HS XOSC is stable and act as the clock source for the system clock). Note: When changing system clock source from HS XOSC to HS RCOSC, there might be a delay from the assertion of SLEEP.HFRC_STB until the actual change of the system clock source (assertion of CLKCON.OSC). This delay is present if the HS RCOSC and/or low power RCOSC is being calibrated when the system clock source change is being initiated. The oscillator not selected as the system clock source, will be set in power-down mode by setting SLEEP.OSC_PD to 1 (the default state). SLEEP.OSC_PD should not be set to 1 before the oscillator selected as the system clock source is reported stable (SLEEP.HFRC_STB=1 or SLEEP.XOSC_STB=1). Please note the minimum requirement on high speed crystal oscillator power down guard time in all modes of operation for CC1110Fx, see Table 11. The HS RCOSC may be turned off when the high speed crystal oscillator has been selected as system clock source and vice versa. Note: HS RCOSC calibration value gets reset to its default value upon waking up from PM{2 - 3}, meaning that any previous calibration result is lost. 12.1.5.2 System Clock Speed and Radio Operation of the RF transceiver requires that the high speed crystal oscillator is used. The CLKCON.CLKSPD setting will limit the maximum data rate, as shown in Table 49. Note that when using FEC (MDMCFG1.FEC_EN=1) CLKCON.CLKSPD must be set to 000. SWRS033G Page 80 of 244 CC1110Fx / CC1111Fx 6.5 and 6.6 for characteristics of these oscillators. Maximum Data Rate [kBaud] CLKCON.CLKSPD MSK GFSK, OOK and ASK 2-FSK 000 500 250 500 001 500 250 500 010 500 250 500 011 500 250 500 100 400 250 400 101 200 200 200 110 100 100 100 111 50 50 50 The CLKCON.OSC32K bit selects the source of the 32 kHz clock. This bit must only be changed while using the HS RCOSC as the system clock source. If CLKCON.OSC32K=1, changing the system clock source to the HS XOSC will initiate the calibration of the low power RC oscillator. The calibration of the low power RC oscillator is continuously performed as long as CLKCON.OSC=0 and the device is in active mode or PM0. The result of the calibration is a RC clock running at 34.667 - 36 kHz for CC1110Fx and 32 kHz for CC1111Fx. Table 49: System Clock Speed vs. Data Rate 12.1.5.3 Low Speed Oscillators (32 kHz clock source) Two low speed oscillators are present in the device: The low power RCOSC calibration takes approximately 2 ms. Except for the initial calibration (first calibration after the HS XOSC was set as source for the system clock (CLKCON.OSC=0)), a calibration will be aborted if one of the following actions is initiated by SW: Low speed crystal oscillator (32.768 kHz) a) Switching the clock source for the system clock from HS XOSC to HS RCOSC by setting CLKCON.OSC=1 Low power RC oscillator (34.667 - 36 kHz for CC1110Fx and 32 kHz for CC1111Fx) b) Entering PM{1 - 3}. The low speed crystal oscillator is designed to operate at 32.768 kHz and provide a stable clock signal for systems requiring time accuracy. The low power RC oscillator run at fXOSC / 750 for CC1110Fx and fXOSC / 1500 for CC1111Fx, when calibrated. The calibration can only take place when the low power RC oscillator is running and the high speed crystal oscillator is enabled and stable, and is initiated by selecting the HS XOSC as the clock source for the system clock (CLKCON.OSC=0). The low power RC oscillator should be used to reduce cost and power consumption compared to the 32.768 kHz crystal oscillator solution. The two low speed oscillators can not be operated simultaneously. If a) or b) is initiated during the initial calibration, the calibration will complete before a) or b) will take place (i.e., the HS XOSC will continue as the clock source for the system clock for up to 2 ms before the switching takes place or PM{1 - 3} is entered). If a) or b) is initiated after the initial calibration has completed, there will be a delay of typically 130 s from SW initiates a) or b), until the calibration is being aborted and the system clock source is changed or PM{1 - 3} is entered (see Figure 18). By default, after a reset, the low power RC oscillator is enabled and selected as the 32 kHz clock source. The RC oscillator consumes less power, but is less accurate than the 32.768 kHz crystal oscillator. Refer to Section Note: During the initial calibration a) or b) can only be initiated once. After the initial calibration has completed and a) or b) is initiated, one must not try to initiate a) or b) again within the next 130 s. Figure 18: Low Power RCOSC Calibration SWRS033G Page 81 of 244 CC1110Fx / CC1111Fx CLKCON (0xC6) - Clock Control Bit Field Name Reset R/W Description 7 OSC32K 1 R/W 32 kHz clock oscillator select. The HS RCOSC must be clock source for the system clock (CLKCON.OSC=1) when this bit is to be changed. 0 32.768 kHz crystal oscillator 1 Low power RC oscillator (32 - 36 kHz for CC1110Fx and 32 kHz for CC1111Fx) Note: This bit is not retained in PM2 and PM3. After re-entry to active mode from one of these power modes this bit will be at the reset value 1. 6 OSC 1 R/W System clock oscillator select. 0 High speed crystal oscillator 1 High speed RC oscillator If the selected oscillator is not already powered up when this bit is set/cleared, it will be powered up by selecting it. This setting will only take effect when the selected oscillator is powered up and stable and when the calibration of the HS RCOSC and initial calibration of the low power RC oscillator is completed. Note: It is not possible to change from high speed RC oscillator to high speed crystal oscillator when SLEEP.MODE00. 5:3 TICKSPD[2:0] 001 R/W Timer tick speed setting. The value of TICKSPD cannot be higher than CLKSPD. CLKCON.OSC=0 HS XOSC used as clock source for system clock CLKCON.OSC=1 Calibrated HS RCOSC used as clock source for system clock 000 fRef 26 MHz NA NA 001 fRef /2 13 MHz fRef /2 13 MHz 010 fRef /4 6.5 MHz fRef /4 6.5 MHz 011 fRef /8 3.25 MHz fRef /8 3.25 MHz 100 fRef /16 1.625 MHz fRef /16 1.625 MHz 101 fRef /32 812.5 kHz fRef /32 812.5 kHz 110 fRef /64 406.25 kHz fRef /64 406.25 kHz 111 fRef /128 203.125 kHz fRef /128 203.125 kHz fRef = fxosc for CC1110Fx and fRef = fxosc/2 for CC1111Fx Numbers above is for CC1110Fx with fxosc = 26 MHz 2:0 CLKSPD[2:0] 001 R/W System clock speed setting. When a new CLKSPD value is written, the new setting is read when the clock has changed. CLKCON.OSC=0 HS XOSC used as clock source for system clock CLKCON.OSC=1 Calibrated HS RCOSC used as clock source for system clock 000 fRef 26 MHz NA NA 001 fRef /2 13 MHz fRef /2 13 MHz 010 fRef /4 6.5 MHz fRef /4 6.5 MHz 011 fRef /8 3.25 MHz fRef /8 3.25 MHz 100 fRef /16 1.625 MHz fRef /16 1.625 MHz 101 fRef /32 812.5 kHz fRef /32 812.5 kHz 110 fRef /64 406.25 kHz fRef /64 406.25 kHz 111 fRef /128 203.125 kHz fRef /128 203.125 kHz fRef = fxosc for CC1110Fx and fRef = fxosc/2 for CC1111Fx Numbers above is for CC1110Fx with fxosc = 26 MHz SWRS033G Page 82 of 244 CC1110Fx / CC1111Fx 12.1.6 Timer Tick Generation The power management controller generates a tick or enable signal for the peripheral timers, thus acting as a prescaler for the timers. This is a global clock division for Timer 1, Timer 2, Timer 3, and Timer 4. The tick speed is programmed from 0.203 to 26 MHz for CC1110Fx assuming a 26 MHz crystal or from 0.1875 to 24 MHz for CC1111Fx by setting the CLKCON.TICKSPD register appropriately. The XDATA memory locations 0xFDA2 0xFEFF (350 bytes) will lose all data when PM2 or PM3 is entered. These locations will contain undefined data when active mode is re-entered. The registers which retain their contents are the CPU registers, peripheral registers and RF registers, unless otherwise specified for a given register bit field. Switching to power modes PM2 and PM3 appears transparent to software with the following exception: Note: CLKCON.TICKSPD cannot be set higher than CLKCON.CLKSPD. 12.1.7 Watchdog timer 15-bit counter is reset to 0x0000 when entering PM2 or PM3 HS RCOSC calibration value gets reset to its default value upon waking up from PM2 and PM3. Data Retention In PM2 and PM3, power is removed from most of the internal circuitry. However, parts of SRAM will retain its contents. The content of internal registers is also retained in PM2 and PM3, with some exceptions (see Table 31, Table 32, and Table 33). The XDATA memory locations 0xF000 0xFFFF (4096 bytes) retain data in PM2 and PM3. Please note the following exception: 12.1.8 I/O and Radio I/O port pins P1_0 and P1_1 do not have internal pull-up/pull-down resistors. These pins should therefore be set as outputs or pulled high/low externally to avoid leakage current. To save power, the radio should be turned off when it is not used. 12.2 Reset The CC1110Fx/CC1111Fx has four reset sources. The following events generate a reset: Forcing RESET_N input pin low A power-on reset condition A brown-out reset condition Watchdog timer reset condition The initial conditions after a reset are as follows: I/O pins are configured as inputs with pull-up, except P1_0 and P1_1. CPU program counter is loaded with 0x0000 and program execution starts at this address All peripheral registers are initialized to their reset values (refer to register descriptions) Watchdog timer is disabled 12.2.1 Power On Reset and Brown Out Detector Brown Out Detector (BOD) operating on the regulated 1.8 V digital power supply only, The BOD will protect the memory contents during supply voltage variations which cause the regulated 1.8 V power to drop below the minimum level required by flash memory and SRAM. When power is initially applied to the CC1110Fx/CC1111Fx the Power On Reset (POR) and Brown Out Detector (BOD) will hold the device in reset state until the supply voltage reaches above the Power On Reset and Brown Out voltages. Figure 19 shows the POR/BOD operation with the 1.8 V (typical) regulated supply voltage together with the active low reset signals BOD_RESET and POR_RESET shown in the bottom of the figure (note that these signals are not available but are included on the figure for illustration purposes). The cause of the last reset can read from the register bits SLEEP.RST. It should be noted that a BOD reset will be read as a POR reset. The CC1110Fx/CC1111Fx includes a Power On Reset (POR) providing correct initialization during device power-on. Also included is a SWRS033G Page 83 of 244 CC1110Fx / CC1111Fx 1.8V REGULATED SUPPLY VOLT UNREGULATED SUPPLY BOD RESET ASSERT POR RESET DEASSERT RISING VDD POR RESET ASSERT FALLING VDD 0 POR OUTPUT BOD RESET POR RESET X X X X X X Figure 19: Power-On-Reset and Brown Out Detector Operation 12.3 Flash Controller The CC1110Fx/CC1111Fx contains 8, 16 or 32 KB flash memory for storage of program code. The flash memory is programmable from the user software and through the debug interface. See Table 27 on Page 34 for flash memory size options. address written to the address registers FADDRH:FADDRL. The Flash Controller handles writing to the embedded flash memory and erasing of the same memory. The embedded flash memory consists of 8, 16, or 32 pages (each page is 1024 bytes) depending on the total flash size. Note the difference in addressing the flash memory; when accessed by the CPU to read code or data, the flash memory is byteaddressable. When accessed by the Flash Controller, the flash memory is wordaddressable, where a word consists of 16 bits. The Flash features: Controller has the following 16-bit word programmable When performing page erase operations, the flash memory page to be erased is addressed through the register bits FADDRH[5:1]. The next sections describe the procedures for flash write and flash page erase in detail. Page erase 12.3.2 Lock bits for write-protection and code security Data is written to the flash memory by using a program command initiated by writing a 1 to FCTL.WRITE. Flash write operations can program any number of words in the flash memory, single words or block of words in sequence starting at the address set by FADDRH:FADDRL. A bit in a word can be changed from 1 to 0, but not from 0 - 1 (writing a 1 to a bit that is 0 will be ignored). The only way to change a 0 to a 1 is by doing a page erase or chip erase through the debug interface, as the erased bits are set to 1. Flash page erase time: 20 ms Flash chip erase time: 200 ms Flash write time (2 bytes): 20 s Auto power-down during low-frequency CPU clock read access (divided clock source, CLKCON.CLKSPD) 12.3.1 Flash Memory Organization The flash memory is divided into 8, 16, or 32 flash pages consisting of 1 KB each. A flash page is the smallest erasable unit in the memory, while a 16-bit word is the smallest writable unit that may be addressed through the Flash Controller. When performing write operations, the flash memory is word-addressable using a 14-bit Flash Write A write operation is performed using one out of two methods; Through DMA transfer Through CPU SFR access The DMA transfer method is the preferred way to write to the flash memory. A write operation is initiated by writing a 1 to FCTL.WRITE. The address to start writing at is SWRS033G Page 84 of 244 CC1110Fx / CC1111Fx given by FADDRH:FADDRL. During each single write operation FCTL.SWBSY is set high. During a write operation, the data written to the FWDATA register is forwarded to the flash memory. The flash memory is 16-bit wordprogrammable, meaning data is written as 16bit words. The first byte written to FWDATA is the LSB of the 16-bit word. The actual writing to flash memory takes place each time two bytes have been written to FWDATA, meaning that the number of bytes written to flash must be a multiple of two. 0x7FFE 0x7FFF (unified) and not exceed maximum range for the device in use (F8, F16, or F32). When using the DMA to write to flash, the code can be executed from within flash memory. When a flash write operation is executed from RAM, the CPU continues to execute code from the next instruction after initiation of the flash write operation (FCTL.WRITE=1). The FCTL.SWBSY bit must be 0 before accessing the flash after a flash write, otherwise an access violation occurs. This means that FCTL.SWBSY must be 0 before program execution can continue from a location in flash memory. PAGE 32 0x7C00 12.3.2.1 0x7C01 . . . 0x0BFE 0x0BFF . . . PAGE 2 . . . 0x0800 0x0801 . . . 0x03FE 0x03FF . . . 0x0000 PAGE 0 . . . 0x0001 Figure 20: Flash Address (in unified memory space) When accessed by the Flash Controller, the flash memory is word-addressable. Each page in flash consists of 512 words, addressed through FADDRH[0]:FADDRL[7:0]. FADDRH[5:1] is used to indicate the page number. That means that if one wants to write to the byte in flash mapped to address 0x0BFE, FADDRH:FADDRL should be 0x05FF (page 2, word 511). The CPU will not be able to access the flash, e.g. to read program code, while a flash write operation is in progress. Therefore the program code executing the flash write must be executed from RAM, meaning that the program code must reside in the area starting from address 0xF000 in CODE memory space DMA Flash Write When using the DMA to write to flash, the data to be written is stored in the XDATA memory space (RAM or flash). A DMA channel should be configured to have the location of the stored data as source address and the Flash Write Data register, FWDATA, as the destination address. The DMA trigger event FLASH should be selected (TRIG[4:0]=10010). Please see Section 12.5 for more details regarding DMA operation. Thus the Flash Controller will trigger a DMA transfer when the Flash Write Data register, FWDATA, is ready to receive new data. When the DMA channel is armed, starting a flash write by setting FCTL.WRITE to 1 will trigger the first DMA transfer. Figure 21 shows an example on how a DMA channel is configured and how a DMA transfer is initiated to write a block of data from a location in XDATA to flash memory. The DMA channel should be configured to operate in single transfer mode, the transfer count should be equal the size of the data block to be transferred (must be a multiple of 2), and each transfer should be a byte. Source address should be incremented by one for each transfer, while the destination address should be fixed. SWRS033G Page 85 of 244 CC1110Fx / CC1111Fx Figure 21: Flash Write using DMA When performing DMA flash write while executing code from within flash memory, the instruction that triggers the first DMA trigger event FLASH (TRIG[4:0]=10010) must be aligned on a 2-byte boundary. Figure 22 shows an example of code that correctly aligns the instruction for triggering DMA (Note that this code is IAR specific). The code below is shown for CC1110Fx, but will also work for CC1111Fx if the include file is being replaced by ioCC1111.h ; Write flash and generate FLASH DMA trigger ; Code is executed from flash memory ; #include "ioCC1110.h" MODULE flashDmaTrigger.s51 RSEG RCODE (1) PUBLIC halFlashDmaTrigger FUNCTION halFlashDmaTrigger, 0203H halFlashDmaTrigger: ORL FCTL, #0x02; RET; END; Figure 22: DMA Flash Write Executed from within Flash Memory 12.3.2.2 CPU Flash Write The CPU can also write directly to the flash when executing program code from RAM using unified memory space. The CPU writes data to the Flash Write Data register, FWDATA. The flash memory is written each time two bytes have been written to FWDATA, if a write has been enabled by setting FCTL.WRITE to 1. The CPU can poll the FCTL.SWBSY status to determine when the flash is ready for two new bytes to be written to FWDATA. Note that there exist a timeout period of 40 s for writing one flash word to FWDATA, thus writing two bytes to the FWDATA register has to end within 40 s after FCTL.SWBSY went low and also within 40 s after a write has been initiated by writing a 1 to FCTL.WRITE (see Figure 24). Failure to do so will clear the FCTL.BUSY bit. FADDRH:FADDRL will contain the address of the location where the write operation failed. A new write operation can be started by setting FCTL.WRITE to 1 again and write two bytes to FWDATA. If one wants to do the whole write operation over again and not just start from where it failed, one has to erase the page, writing the start address to FADDRH:FADDRL, and setting FCTL.WRITE to 1 (see Section 1.1.1). SWRS033G Page 86 of 244 CC1110Fx / CC1111Fx The steps required to start a CPU flash write operation are shown in Figure 23. Note that code must be run from RAM in unified memory space. Figure 23: CPU Flash Write Executed from RAM Figure 24. Flash Write Timeout 12.3.3 Flash Page Erase Note: If flash erase operations are performed from within flash memory and the watchdog timer is enabled, a watchdog timer interval must be selected that is longer than 20 ms, the duration of the flash page erase operation, so that the CPU will manage to clear the watchdog timer. After a flash page erase, all bytes in the erased page are set to 1. A page erase is initiated by setting FCTL.ERASE to 1. The page addressed by FADDRH[5:1] is erased when a page erase is initiated. Note that if a page erase is initiated simultaneously with a page write, i.e. FCTL.WRITE is set to 1, the page erase will be performed before the page write operation. The FCTL.BUSY bit can be polled to see when the page erase has completed. The steps required to perform a flash page erase from within flash memory are outlined in Figure 25. Note that, while executing program code from within flash memory, when a flash erase or write operation is initiated, program execution SWRS033G Page 87 of 244 CC1110Fx / CC1111Fx will resume from the next instruction when the Flash Controller has completed the operation. The flash erase operation requires that the instruction that starts the erase i.e. writing to ; Erase page ; Assumes 26 ; CLR C1: MOV JB MOV MOV MOV NOP RET FCTL.ERASE is followed by a NOP instruction as shown in the example code. Omitting the NOP instruction after the flash erase operation will lead to undefined behavior. 1 in flash memory MHz system clock is used EA A,FCTL ACC.7,C1 FADDRH,#02h FWT,#2Ah FCTL,#01h ; Mask interrupts ; Wait until flash controller is ready ; ; ; ; ; Setup flash address (FADDRH[5:1]=1) Setup flash timing Erase page Must always execute a NOP after erase Continues here when flash is ready Figure 25: Flash Page Erase Performed from Flash Memory 12.3.4 Flash DMA trigger When the DMA channel is armed and the FLASH trigger selected TRIG[4:0]=10010, starting a flash write by setting FCTL.WRITE to 1 will trigger the first DMA transfer. The following DMA transfers will be triggered by the Flash Controller when the Flash Write Data register, FWDATA, is ready to receive new data. 12.3.5 Flash Write Timing The Flash Controller contains a timing generator, which controls the timing sequence of flash write and erase operations. The timing generator uses the information set in the Flash Write Timing register, FWT.FWT[5:0], to set the internal timing. FWT.FWT[5:0] must be set to a value according to the currently selected system clock frequency. The value used for FWT.FWT[5:0] is given by the following equation: FWT 21000 F 16 109 where F is the system clock frequency. The initial value held in FWT.FWT[5:0] after a reset is 0x11, which corresponds to 13 MHz system clock frequency (calibrated HS RCOSC frequency for CC1110Fx when using a 26 MHz XOSC). 12.3.6 Flash Controller Registers The Flash Controller registers are described in this section. SWRS033G Page 88 of 244 CC1110Fx / CC1111Fx FCTL (0xAE) - Flash Control Bit Field Name Reset R/W Description 7 BUSY 0 R Indicates that write or erase is in operation when set to 1 6 SWBSY 0 R Indicates that a flash write is in progress. This byte is set to 1 after two bytes has been written to FWDATA. Do not write to FWDATA register while this bit is set. 5 4 CONTRD 3:2 1 WRITE R/W R0 Not used 0 Continuous read enable 0 Disable. To avoid wasting power, continuous read should only be enabled when needed 1 Enable. Reduces internal switching of read enables, but greatly increases power consumption. 00 R0 Not used 0 R0/W When set to 1, a program command used to write data to flash memory is initiated. If ERASE is set to 1at the same time as this bit is set to 1, a page erase of the whole page addressed by FADDRH[6:1] is performed before the write. This bit will be 0 when returning from PM2 and PM3 0 ERASE 0 R0/W Page Erase. Erase page given by FADDRH[5:1]. This bit will be 0 when returning from PM2 and PM3 FWDATA (0xAF) - Flash Write Data Bit Field Name Reset R/W Description 7:0 FWDATA[7:0] 0x00 R/W If FCTL.WRITE is set to 1, writing two bytes in a row to this register starts the actual writing to flash memory. FCTL.SWBSY will be 1 during the actual flash write FADDRH (0xAD) - Flash Address High Byte Bit Field Name 7:6 5:0 FADDRH[5:0] Reset R/W Description 0 R/W Not used 000000 R/W Page address / High byte of flash word address Bits 5:1 will select which page to access. FADDRL (0xAC) - Flash Address Low Byte Bit Field Name Reset R/W Description 7:0 FADDRL[7:0] 0x00 R/W Low byte of flash address FWT (0xAB) - Flash Write Timing Bit Field Name 7:6 5:0 FWT[5:0] Reset R/W Description 0 R/W Not used 0x11 R/W Flash Write Timing. Controls flash timing generator. FWT 21000 F , where F is the system clock frequency (see Section 12.3.5) 16 10 9 SWRS033G Page 89 of 244 CC1110Fx / CC1111Fx 12.4 I/O Ports Note: P0_6 and P0_7 do not exist on CC1111Fx. The CC1111Fx has 19 digital input/output pins available and the ADC inputs A6 and A7 can not be used. Apart from this, all information in this section applies to both CC1111Fx and CC1110Fx. For all registers in this section, an x in the register name can be replaced by 0, 1, or, 2, referring to the port number, if nothing else is stated. The CC1110Fx has 21 digital input/output pins that can be configured as general purpose digital I/O or as peripheral I/O signals 2 connected to the ADC, Timers, I S, or USART peripherals. The usage of the I/O ports is fully configurable from user software through a set of configuration registers. The I/O ports have the following key features: 21 digital input/output pins General purpose I/O or peripheral I/O Pull-up or pull-down capability on inputs, except on P1_0 and P1_1. External interrupt capability The external interrupt capability is available on all 21 I/O pins. Thus, external devices may generate interrupts if required. The external interrupt feature can also be used to wake up from all four power modes (PM{0 - 3}). 12.4.1 General Purpose I/O When used as general purpose I/O, the pins are organized as three 8-bit ports, port 0, 1, and 2, denoted P0, P1, and P2. P0 and P1 are complete 8-bit wide ports while P2 has only five usable bits (P2_0 to P2_4). All ports are both bit- and byte addressable through the SFRs P0, P1 and P2. Each port pin can individually be set to operate as a general purpose I/O or as a peripheral I/O. Note: P1_0 and P1_1 have LED driving capabilities. To use a port as a general purpose I/O pin the pin must first be configured. The registers PxSEL are used to configure each pin in a port either as a general purpose I/O pin or as a peripheral I/O signal. All digital input/output pins are configured as general-purpose I/O 2 pins by default. Note that when the I S interface is enabled (I2SCFG0.ENAB=1), the 2 I S interface will control its corresponding pins even if these are selected to be general purpose I/O pins in the PxSEL register. By default, all general-purpose I/O pins are configured as inputs. To change the direction of a port pin, at any time, the registers PxDIR are used to set each port pin to be either an input or an output. Thus by setting the appropriate bit within PxDIR to 1, the corresponding pin becomes an output. When reading the port registers P0, P1, and P2, the logic values on the input pins are returned regardless of the pin configuration. This does not apply during the execution of read-modify-write instructions. The readmodify-write instructions are: ANL, ORL, XRL, JBC, CPL, INC, DEC, DJNZ, and MOV, CLR, or SETB. Operating on a port registers the following is true: When the destination is an individual bit in a port register P0, P1 or P2 the value of the register, not the value on the pin, is read, modified, and written back to the port register. When used as an input, the general purpose I/O port pins can be configured to have a pullup, pull-down, or tri-state mode of operation. By default, inputs are configured as inputs with pull-up. To de-select the pull-up/pull-down function on an input the appropriate bit within the PxINP must be set to 1. The I/O port pins P1_0 and P1_1 do not have pull-up/pull-down capability. In PM1, PM2, and PM3 the I/O pins retain the I/O mode and output value (if applicable) that was set when PM{1 - 3} was entered. 12.4.2 Unused I/O Pins Unused I/O pins should have a defined level and not be left floating. One way to do this is to leave the pin unconnected and configure the pin as a general purpose I/O input with pull-up resistor. This is the default state of all pins after reset except for P1_0 and P1_1 which do not have pull-up/pull-down resistors (note that only P2_2 has pull-up during reset). Alternatively the pin can be configured as a general purpose I/O output. In both cases the pin should not be connected directly to VDD or GND in order to avoid excessive power consumption. SWRS033G Page 90 of 244 CC1110Fx / CC1111Fx 12.4.3 Low I/O Supply Voltage P1IEN: P1 interrupt enables PICTL: P0/P2 interrupt enables and P0, P1, and P2 edge configuration In applications where the digital I/O power supply voltage VDD on pin DVDD is below 2.6 V, the register bit IOCFG1.GDO_DS should be set to 1. P0IFG: P0 interrupt status flags P1IFG: P1 interrupt status flags 12.4.4 General Purpose I/O Interrupts P2IFG: P2 interrupt status flags General purpose I/O pins configured as inputs can be used to generate interrupts. The interrupts can be configured to trigger on either a rising or falling edge of the external signal. Each of the P0, P1 and P2 ports have separate interrupt enable bits common for all bits within the port located in the IENx registers as follows: IEN1.P0IE : P0 interrupt enable IEN2.P1IE : P1 interrupt enable IEN2.P2IE : P2 interrupt enable In addition to these common interrupt enables, the bits within each port have interrupt enable bits located in I/O port SFRs. Each bit within P1 has an individual interrupt enable bit, P1_xIEN, where x is 0 - 7, located in the P1IEN register. For P0, the low-order nibble and the high-order nibble have their individual interrupt enables, P0IENL and P0IENH respectively, found in the PICTL register. For the P2_0 - P2_4 inputs there is a common interrupt enable, P2IEN, in the PICTL register. When an interrupt condition occurs on one of the general purpose I/O pins, the corresponding interrupt status flag in the P0 P2 interrupt status flag registers, P0IFG , P1IFG, or P2IFG will be set to 1. The interrupt status flag is set regardless of whether the pin has its interrupt enable set. The CPU interrupt flags located in IRCON2 for P1 and P2, and IRCON for P0, will only be asserted if one or more of the interrupt enable bits found in P1IEN (P1) and PICTL (P0 and P2) are set to 1. Note that the module interrupt flag needs to be cleared prior to clearing the CPU interrupt flag. Note: All port interrupts are blocked when SLEEP.MODE00 12.4.5 General Purpose I/O DMA When used as general purpose I/O pins, the P0_1 and P1_3 pins are each associated with one DMA trigger. These DMA triggers are IOC_0 for P0_1 and IOC_1 for P1_3 as shown in Table 51 on Page 107. The IOC_0 DMA trigger is activated when there is a rising edge on P0_1 (P0SEL.SELP0_1 and P0DIR.P0_1 must be 0) and IOC_1 is activated when there is a falling edge on P1_3 (P1SEL.SELP1_3 and P1DIR.P1_3 must be 0). Note that only input transitions on pins configured as general purpose I/O, inputs will produce a DMA trigger. 12.4.6 Peripheral I/O This section describes how the digital input/output pins are configured as peripheral I/Os. For each peripheral unit that can interface with an external system through the digital input/output pins, a description of how peripheral I/Os are configured is given in the following sub-sections. In general, setting the appropriate PxSEL bits to 1 is required to select peripheral I/O function on a digital I/O pin. Note that peripheral units have two alternative locations for their I/O pins. Please see Table 50. The SFRs used for I/O interrupts are described in Section 10.5 on Page 60. The registers are the following: SWRS033G Page 91 of 244 CC1110Fx / CC1111Fx Periphery / P0 P1 P2 Function ADC 714 614 5 4 3 2 1 0 A7 A6 A5 A4 A3 A2 A1 A0 C SS M0 MI USART0 Alt. 1 SPI CT TX RX MI M0 C SS RX TX RT CT Alt. 2 USART1 Alt. 1 UART RT Alt. 2 USART1 Alt. 1 SPI 6 Alt. 2 USART0 Alt. 1 UART 7 Alt. 2 TIMER1 Alt. 1 2 1 5 4 3 2 MO MI C SS TX RX RT CT MI M0 C SS RX TX RT CT 1 0 1 2 1 0 4 2 1 0 TIMER3 Alt. 1 1 Alt. 2 1 0 0 TIMER4 Alt. 1 Alt. 2 1 Alt. 1 0 0 Alt. 2 I2S 3 CK WS RX 0 TX Alt. 2 CK 32.768 kHz XOSC Q2 DEBUG WS RX DC DD TX Q1 Table 50: Peripheral I/O Pin Mapping 14 This pin is only found on CC1110Fx ,it does not exist on CC1111Fx. 12.4.6.1 USART0 The SFR bit PERCFG.U0CFG selects whether to use alternative 1 or alternative 2 locations. In Table 50, the USART0 signals are shown as follows: SPI: SCK: C SSN: SS 15 MOSI: MO MISO: MI P2DIR.PRIP0 selects the order of precedence when assigning two peripherals to the same pin location on P0. When set to 00, USART0 has precedence if both USART0 and USART1 are assigned to the same pins. Note that if USART0 is configured to operate in UART mode with hardware flow control disabled, USART1 or timer 1 will have precedence to use ports P0_4 and P0_5. It is the user's responsibility to not assign more than two peripherals to the same pin locations, as P2DIR.PRIP0 will not give a conclusive order of precedence if more than two peripherals are in conflict on a pin. UART: RXDATA: RX TXDATA: TX RTS: RT CTS: CT 15 SSN should only be configured as a peripheral when using SPI slave mode P2SEL.PRI3P1, P2SEL.PRI2P1, P2SEL.PRI1P1, and P2SEL.PRI0P1 select the order of precedence when assigning two, and in some cases three, peripherals to P1. An example is if both the USARTs are assign to P1 together with Timer 1 (channel 2, 1, and 0). By setting both PRI3P1 and PRI0P1 to 0, USART0 will have precedence. Note that if USART0 is configured to operate in UART mode with hardware flow control disabled, USART1 can still use P1_7 and P1_6, while Timer 1 can use P1_2, P1_1, and P1_0. Also SWRS033G Page 92 of 244 CC1110Fx / CC1111Fx on P1 it is the user's responsibility to make sure that there is a conclusive order of precedence based on the PERCFG and P2SEL settings. 12.4.6.2 responsibility to avoid configurations where the order of precedence is not conclusive. 12.4.6.3 PERCFG.T1CFG selects whether to alternative 1 or alternative 2 locations. USART1 The SFR bit PERCFG.U1CFG selects whether to use alternative 1 or alternative 2 locations. In Table 50, the USART1 signals are shown as follows: Channel 0 capture/compare pin: 0 Channel 1 capture/compare pin: 1 SCK: C Channel 2 capture/compare pin: 2 16 P2DIR.PRIP0 selects the order of precedence when assigning two peripherals to the same pin location on P0. When set to 10 or 11, Timer 1 has precedence over USART1 and USART0 respectively. It is the user's responsibility to not assign more than two peripherals to the same pin locations MOSI: MO MISO: MI UART: RXDATA: RX TXDATA: TX RTS: RT CTS: CT P2DIR.PRIP0 selects the order of precedence when assigning two peripherals to the same pin location on P0. When set to 01, USART1 has precedence if both USART0 and USART1 are assigned to the same pins. Note that if USART1 is configured to operate in UART mode with hardware flow control disabled, USART0 or timer 1 will have precedence to use ports P0_3 and P0_2. It is the user's responsibility to not assign more than two peripherals to the same pin locations, as P2DIR.PRIP0 will not give a conclusive order of precedence if more than two peripherals are in conflict on a pin. P2SEL.PRI3P1, P2SEL.PRI2P1, P2SEL.PRI1P1, and P2SEL.PRI0P1 select the order of precedence when assigning two, and in some cases three, peripherals to P1. By setting PRI3P1 to 1 and PRI2P1 to 0, USART1 will have precedence over both USART0 and Timer 3. However, if USART1 is configured to operate in UART mode with hardware flow control disabled, there will be a conflict on P1_4 between USART0 and Timer 3 (channel 1), which the P2SEL register settings do not solve. It is the user's 16 use In Table 50, the Timer 1 signals are shown as follows: SPI: SSN: SS Timer 1 SSN should only be configured as a peripheral when using SPI slave mode P2SEL.PRI3P1, P2SEL.PRI2P1, P2SEL.PRI1P1, and P2SEL.PRI0P1 select the order of precedence when assigning two, and in some cases three, peripherals to P1. When P2SEL.PRI1P1=0 and P2SEL.PRI0P1=1, Timer 1 has precedence over Timer 4 and USART0 respectively. It is the user's responsibility to avoid configurations where the order of precedence is not conclusive. 12.4.6.4 Timer 3 PERCFG.T3CFG selects whether to alternative 1 or alternative 2 locations. use In Table 50, the Timer 3 signals are shown as follows: Channel 0 compare pin: 0 Channel 1 compare pin: 1 P2SEL.PRI3P1, P2SEL.PRI2P1, P2SEL.PRI1P1, and P2SEL.PRI0P1 select the order of precedence when assigning two, and in some cases three, peripherals to P1. Setting P2SEL.PRI2P1=1 gives Timer 3 precedence over USART1. It is the user's responsibility to avoid configurations where the order of precedence is not conclusive. 12.4.6.5 Timer 4 PERCFG.T4CFG selects whether to alternative 1 or alternative 2 locations. use In Table 50, the Timer 4 signals are shown as follows: SWRS033G Page 93 of 244 CC1110Fx / CC1111Fx Channel 0 compare pin: 0 configured as a general-purpose I/O in input mode, when being used for ADC external trigger. Channel 1 compare pin: 1 P2SEL.PRI3P1, P2SEL.PRI2P1, P2SEL.PRI1P1, and P2SEL.PRI0P1 select the order of precedence when assigning two, and in some cases three, peripherals to P1. Setting P2SEL.PRI12P1=1 gives Timer 4 precedence over Timer 1. It is the user's responsibility to avoid configurations where the order of precedence is not conclusive. 2 12.4.6.6 IS 2 The IS configuration register bit I2SCFG1.IOLOC selects whether to use alternative 1 or alternative 2 locations. 2 In Table 50, the I S signals are shown as follows: Continuous Serial Clock (SCK): CK Word Select: WS Serial Data In: RX Serial Data Out: TX Refer to Section 12.10 on Page 140 for a detailed description on how to use the ADC. 12.4.6.8 Debug Interface Ports P2_1 and P2_2 are used for debug data and clock signals, respectively. These are shown as DD (debug data) and DC (debug clock) in Table 50. The state of P2SEL is overridden by the debug interface. Also, P2DIR.DIRP2_1 and P2DIR.DIRP2_2 is overridden when the chip changes the direction to supply the external host with data. 12.4.6.9 32.768 kHz XOSC Input Ports P2_3 and P2_4 are used to connect to an external 32.768 kHz crystal. These port pins will be set in analog mode and used by the 32.768 kHz crystal oscillator when CLKCON.OSC32K is low, regardless of the configurations of these pins. 2 If the IS interface is enabled 2 (I2SCFG0_ENAB=1), the I S interface will have precedence in cases where other peripherals (except for the debug interface) are configured to be on the same location. This is the case even if the pins are configured to be general purpose I/O pins. 12.4.6.7 ADC When using the ADC in an application, some or all of the P0 pins must be configured as ADC inputs. The port pins are mapped to the ADC inputs so that P0_7 - P0_0 corresponds to AIN7 - AIN0. To configure a P0 pin to be used as an ADC input the corresponding bit in the ADCCFG register must be set to 1. The default values in this register select the Port 0 pins as non-ADC input i.e. digital input/outputs. 12.4.6.10 Radio Test Output Signals For debug and test purposes, a number of internal status signals in the radio may be output on the port pins P1_7 - P1_5. This debug option is controlled through the RF registers IOCFG2 - IOCFG0 (see Section 15 for more details). Setting IOCFGx.GDOx_CFG to a value other than 0 will override the P1SEL_SELP1_7, P1SEL_SELP1_6, and P1SEL_SELP1_5 settings, and the pins will automatically become outputs. These pins cannot be used 2 when the I S interface is enabled. 12.4.7 I/O Registers The registers for the IO ports are described in this section. The registers are: P0 Port 0 Note: P0_6 and P0_7 do not exist on CC1111Fx, hence six input channels are available (AIN0 - AIN5) P1 Port 1 P2 Port 2 The settings in the ADCCFG register override the settings in P0SEL (the register used to select a pin to be either GPIO or to have a peripheral function). The ADC can be configured to use the general-purpose I/O pin P2_0 as an external trigger to start conversions. P2_0 must be SWRS033G PERCFG Peripheral Control ADCCFG ADC Input Configuration P0SEL Port 0 Function Select P1SEL Port 1 Function Select P2SEL Port 2 Function Select Page 94 of 244 CC1110Fx / CC1111Fx P0DIR Port 0 Direction P0IFG Port 0 Interrupt Status Flag P1DIR Port 1 Direction P1IFG Port 1 Interrupt Status Flag P2DIR Port 2 Direction P2IFG Port 2 Interrupt Status Flag P0INP Port 0 Input Mode PICTL Port Interrupt Control P1INP Port 1 Input Mode P1IEN Port 1 Interrupt Mask P2INP Port 2 Input Mode P0 (0x80) - Port 0 Bit Field Name Reset R/W Description 7:0 P0[7:0] 0xFF R/W Port 0. General purpose I/O port. Bit-addressable. P1 (0x90) - Port 1 Bit Field Name Reset R/W Description 7:0 P1[7:0] 0xFF R/W Port 1. General purpose I/O port. Bit-addressable. Reset R/W Description 111 R/W Not used 11111 R/W Port 2. General purpose I/O port. Bit-addressable. P2 (0xA0) - Port 2 Bit Field Name 7:5 4:0 P2[4:0] PERCFG (0xF1) - Peripheral Control Bit Field Name 7 6 5 4 T1CFG T3CFG T4CFG 3:2 1 0 U1CFG U0CFG Reset R/W Description 0 R0 Not used 0 R/W Timer 1 I/O location 0 0 R/W R/W 0 Alternative 1 location 1 Alternative 2 location Timer 3 I/O location 0 Alternative 1 location 1 Alternative 2 location Timer 4 I/O location 0 Alternative 1 location 1 Alternative 2 location 00 R0 Not used 0 R/W USART1 I/O location 0 R/W 0 Alternative 1 location 1 Alternative 2 location USART0 I/O location 0 Alternative 1 location 1 Alternative 2 location SWRS033G Page 95 of 244 CC1110Fx / CC1111Fx ADCCFG (0xF2) - ADC Input Configuration Bit Field Name Reset R/W Description 7:0 ADCCFG[7:0] 0x00 R/W ADC input configuration. ADCCFG[7:0] select P0_7 - P0_0 as ADC inputs AIN7 - AIN0 0 ADC input disabled 1 ADC input enabled P0SEL (0xF3) - Port 0 Function Select Bit Field Name Reset R/W Description 7:0 SELP0_[7:0] 0x00 R/W P0_7 to P0_0 function select 0 General purpose I/O 1 Peripheral function P1SEL (0xF4) - Port 1 Function Select Bit Field Name Reset R/W Description 7:0 SELP1_[7:0] 0 R/W P1_7 to P1_0 function select 0 General purpose I/O 1 Peripheral function SWRS033G Page 96 of 244 CC1110Fx / CC1111Fx P2SEL (0xF5) - Port 2 Function Select Bit Field Name 7 6 5 4 3 2 1 0 PRI3P1 PRI2P1 PRI1P1 PRI0P1 SELP2_4 SELP2_3 SELP2_0 Reset R/W Description 0 R0 Not used 0 R/W Port 1 peripheral priority control. These bits shall determine the order of precedence in the case when PERCFG assigns USART0 and USART1 to the same pins. 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W 0 USART0 has priority 1 USART1 has priority Port 1 peripheral priority control. These bits shall determine the order of precedence in the case when PERCFG assigns USART1 and timer 3 to the same pins. 0 USART1 has priority 1 Timer 3 has priority Port 1 peripheral priority control. These bits shall determine the order of precedence in the case when PERCFG assigns timer 1 and timer 4 to the same pins. 0 Timer 1 has priority 1 Timer 4 has priority Port 1 peripheral priority control. These bits shall determine the order of precedence in the case when PERCFG assigns USART0 and timer 1 to the same pins. 0 USART0 has priority 1 Timer 1 has priority P2_4 function select 0 General purpose I/O 1 Peripheral function P2_3 function select 0 General purpose I/O 1 Peripheral function P2_0 function select 0 General purpose I/O 1 Peripheral function P0DIR (0xFD) - Port 0 Direction Bit Field Name Reset R/W Description 7:0 DIRP0_[7:0] 0x00 R/W P0_7 to P0_0 I/O direction 0 Input 1 Output P1DIR (0xFE) - Port 1 Direction Bit Field Name Reset R/W Description 7:0 DIRP1_[7:0] 0x00 R/W P1_7 to P1_0 I/O direction 0 Input 1 Output SWRS033G Page 97 of 244 CC1110Fx / CC1111Fx P2DIR (0xFF) - Port 2 Direction Bit Field Name Reset R/W Description 7:6 PRIP0[1:0] 00 R/W Port 0 peripheral priority control. These bits shall determine the order of precedence in the case when PERCFG assigns two peripherals to the same pins 5 4:0 DIRP2_[4:0] 00 USART0 - USART1 01 USART1 - USART0 10 Timer 1 channels 0 and 1 - USART1 11 Timer 1 channel 2 - USART0 0 R0 Not used 00000 R/W P2_4 to P2_0 I/O direction 0 Input 1 Output P0INP (0x8F) - Port 0 Input Mode Bit Field Name Reset R/W Description 7:0 MDP0_[7:0] 0x00 R/W P0_7 to P0_0 I/O input mode 0 Pull-up / pull-down 1 Tristate P1INP (0xF6) - Port 1 Input Mode Bit Field Name Reset R/W Description 7:2 MDP1_[7:2] 00000 0 R/W P1_7 to P1_2 I/O input mode, note that P1_1 and P1_0 do not have pull capability 1:0 00 R0 0 Pull-up / pull-down 1 Tristate Not used P2INP (0xF7) - Port 2 Input Mode Bit Field Name Reset R/W Description 7 PDUP2 0 R/W Port 2 pull-up/down select. Selects function for all Port 2 pins configured as pullup/pull-down inputs. 6 5 4:0 PDUP1 PDUP0 MDP2_[4:0] 0 0 00000 R/W R/W R/W 0 Pull-up 1 Pull-down Port 1 pull-up/down select. Selects function for all Port 1 pins configured as pullup/pull-down inputs, except for P1_0 and P1_1, which do not have pull-up/down capability. 0 Pull-up 1 Pull-down Port 0 pull-up/down select. Selects function for all Port 0 pins configured as pullup/pull-down inputs. 0 Pull-up 1 Pull-down P2_4 to P2_0 I/O input mode 0 Pull-up / pull-down 1 Tristate SWRS033G Page 98 of 244 CC1110Fx / CC1111Fx P0IFG (0x89) - Port 0 Interrupt Status Flag CC1110Fx Bit Field Name Reset R/W Description 7:0 P0IF[7:0] 0x00 R/W0 Port 0, inputs 7 to 0 interrupt status flags. 0 No interrupt pending 1 Interrupt pending CC1111Fx Bit Field Name Reset R/W Description 7 USB_RESUME 0 R/W0 USB resume detected during suspend mode 0 R/W0 Not used 0 R/W0 Port 0, inputs 5 to 0 interrupt status flags. 6 5:0 P0IF[5:0] 0 No interrupt pending 1 Interrupt pending P1IFG (0x8A) - Port 1 Interrupt Status Flag Bit Field Name Reset R/W Description 7:0 P1IF[7:0] 0x00 R/W0 Port 1, inputs 7 to 0 interrupt status flags. 0 No interrupt pending 1 Interrupt pending P2IFG (0x8B) - Port 2 Interrupt Status Flag Bit Field Name 7:5 4:0 P2IF[4:0] Reset R/W Description 0 R0 Not used 0 R/W0 Port 2, inputs 4 to 0 interrupt status flags. 0 No interrupt pending 1 Interrupt pending SWRS033G Page 99 of 244 CC1110Fx / CC1111Fx PICTL (0x8C) - Port Interrupt Control Bit Reset R/W Description 7 0 R0 Not used 6 0 R/W Not Used 0 R/W Port 2, inputs 4 to 0 interrupt enable. 5 4 3 2 1 0 Field Name P2IEN P0IENH P0IENL P2ICON P1ICON P0ICON 0 0 0 0 0 R/W R/W R/W R/W R/W 0 Interrupts are disabled 1 Interrupts are enabled Port 0, inputs 7 to 4 interrupt enable. 0 Interrupts are disabled 1 Interrupts are enabled Port 0, inputs 3 to 0 interrupt enable. 0 Interrupts are disabled 1 Interrupts are enabled Port 2, inputs 4 to 0 interrupt configuration. This bit selects the interrupt request condition for all port 2 inputs 0 Rising edge on input gives interrupt 1 Falling edge on input gives interrupt Port 1, inputs 7 to 0 interrupt configuration. This bit selects the interrupt request condition for all port 1 inputs 0 Rising edge on input gives interrupt 1 Falling edge on input gives interrupt Port 0, inputs 7 to 0 interrupt configuration. This bit selects the interrupt request condition for all port 0 inputs. For CC1111Fx , this bit must be set to 0 when USB is used, since the internal USB resume interrupt mapped to P0[7] uses rising edge. 0 Rising edge on input gives interrupt 1 Falling edge on input gives interrupt P1IEN (0x8D) - Port 1 Interrupt Mask Bit Field Name Reset R/W Description 7:0 P1_[7:0]IEN 0x00 R/W Port P1_7 to P1_0 interrupt enable 0 Interrupts are disabled 1 Interrupts are enabled SWRS033G Page 100 of 244 CC1110Fx / CC1111Fx 12.5 DMA Controller The CC1110Fx/CC1111Fx includes a direct memory access (DMA) controller, which can be used to relieve the 8051 CPU core of handling data movement operations. Because of this, the CC1110Fx/CC1111Fx can achieve high overall performance with good power efficiency. The DMA controller can move data from a peripheral unit such as the ADC or RF transceiver to memory with minimum CPU intervention. The DMA controller coordinates all DMA transfers, ensuring that DMA requests are prioritized appropriately relative to each other and CPU memory access. The DMA controller contains 5 programmable DMA channels for data movement. The DMA controller controls data movement over the entire XDATA memory space. Since most of the SFRs are mapped into the XDATA memory space these flexible DMA channels can be used to unburden the CPU in 2 innovative ways, e.g. feed a USART and I S with data from memory, periodically transfer samples between ADC and memory, transfer data to and from USB FIFOs (CC1111Fx) etc. Use of the DMA can also reduce system power consumption by keeping the CPU idle and not have it to wake up to move data to or from a peripheral unit (see Section 12.1.2). Note that Section 10.2.3.3 describes which SFRs are not mapped into XDATA memory space. The main features of the DMA controller are as follows: Five independent DMA channels Three configurable channel priority levels of DMA 30 configurable trigger events Independent control of source and destination address Single, block, and repeated transfer modes Supports variable transfer count length by including the length field in the data to be transferred Can operate in either word-size or bytesize mode 12.5.1 DMA Operation There are five DMA channels available in the DMA controller numbered channel 0 to channel 4. Each DMA channel can move data from one place within XDATA memory space to another i.e. between XDATA locations. Some CPU-specific SFRs reside inside the CPU core and can only be accessed using the SFR memory space and can therefore not be accessed using DMA. These registers are shown in gray in Table 30 on Page 47. Note: In the following sections, an n in the register name represent the channel number 0, 1, 2, 3, or 4 if nothing else is stated In order to use a DMA channel it must first be configured as described in Sections 0 and 12.5.3. Once a DMA channel has been configured it must be armed before any transfers are allowed to be initiated. A DMA channel is armed by setting the appropriate bit DMAARMn in the DMA Channel Arm register DMAARM. When a DMA channel is armed it will start to move data when the configured DMA trigger event occurs. When a DMA channel is armed a transfer will begin when the configured DMA trigger event occurs. Note that it takes 9 system clocks from the arm bit is set until the new configuration is loaded. While the new configuration is being loaded, the DMA channel will be able to accept triggers. This will, however, not be the trigger stored in the configuration data that are currently loaded, but the trigger last used with this channel (after a reset this will be trigger number 0, manual trigger using the DMAREQ.DMAREQn bit). If n channels are armed at the same time, loading the configuration takes n x 9 clock cycles. Channel 1 will first be ready, then channel 2, and finally channel 0. It can not be assumed that channel 1 is ready after 9 clock cycles, channel 2 after 18 clock cycles, etc. To avoid having the DMA channels starting to move data on unwanted triggers when changing configuration, a dummy configuration should be loaded in-between configuration changes, setting TRIG to 0. Alternatively, abort the currently armed DMA channel before rearming it. There are 30 possible DMA trigger events, e.g. UART transfer, Timer overflow etc. The DMA trigger events are listed in Table 51. Figure 26 shows a DMA operation flow chart. SWRS033G Page 101 of 244 CC1110Fx / CC1111Fx Initialization Write DMA channel configuration Yes No Reconfigure? DMA Channel Idle No Setting DMAARM.ABORT=1 will abort all channels where the DMAARMn bit is set simultaneously. I.e., setting DMAARM=0x85 will abort channel 0 and channel 2 DMAARM.DMAARMn=1? Yes DMA Channel Armed Load DMA Channel configuration Trigger or DMAREQ.DMAREQn=1? No Yes Transfer one byte or word when channel is granted access Modify source/destination address Yes Reached transfer count? Yes Set interrupt flag. (IRCON.DMAIF=1 DMAIRQ.DMAIFn=1 if IRQMASK=1) Repetitive transfer mode? No DMAARMn=0 No Yes Repetitive transfer mode? No Figure 26: DMA Operation SWRS033G Page 102 of 244 CC1110Fx / CC1111Fx 12.5.2 DMA Configuration Parameters Setup and control of the DMA operation is performed by the user software. This section describes the parameters which must be configured before a DMA channel can be used. Section 12.5.3 on Page 105 describes how the parameters are set up in software and passed to the DMA controller. Variable Length Transfer Count: When VLEN000 and VLEN111, the transfer count is given by the value of the first byte/word in source data, n, + a constant given by the VLEN setting. This allows for variable length transfer count. Note: For byte size transfers (see Section 12.5.2.4), n is defined as the first byte in source data or the 7 LSB of the first byte in source data, depending on the M8 setting (see Section 12.5.2.9). For word size transfers, n is the 13 LSB of the first word in source data. The behavior of each of the five DMA channels is configured with the following parameters: 12.5.2.1 Source Address (SRCADDR) The address of the location in XDATA memory space where the DMA channel shall start to read data. 12.5.2.2 There are four possible configurations: 1. VLEN=001 Transfer number of commanded by n + 1 Destination Address (DESTADDR) 2. VLEN=010 The address of the location in XDATA memory space where the DMA channel will write the data read from the source address. The user must ensure that the destination is writable. 12.5.2.3 Transfer number commanded by n Fixed Length Transfer Count: When VLEN=000 or VLEN=111, the transfer count is set by the LEN setting. of bytes/words Transfer number of commanded by n + 2 bytes/words 3. VLEN=011 Transfer Count The number of bytes/words needed to be moved from source to destination. When the transfer count is reached, the DMA controller rearms or disarms the DMA channel (depending on transfer mode) and alert the CPU by setting the DMAIRQ.DMAIFn bit to 1. If IRQMASK=1, IRCON.DMAIF will also be set and an interrupt request is generated if IEN1.DMAIE=1. The transfer count can be of fixed or variable length depending on how the DMA channel is configured. bytes/words 4. VLEN=100 Transfer number of commanded by n + 3 bytes/words For all of the above configurations, the transfer count will be limited to LEN bytes/words when n LEN. In cases where n < LEN, the transfer count is given by the VLEN setting. This means that when VLEN=010, LEN should be equal to nmax, while in the other three cases, LEN should be set to nmax + 1. Figure 27 shows the different VLEN options. SWRS033G Page 103 of 244 CC1110Fx / CC1111Fx Byte/Word n+2 Byte/Word n+1 Byte/Word n+1 Byte/Word n+1 Byte/Word n+1 Byte/Word n Byte/Word n Byte/Word n Byte/Word n Byte/Word n-1 Byte/Word n-1 Byte/Word n-1 Byte/Word n-1 Byte/Word n-2 Byte/Word n-2 Byte/Word n-2 Byte/Word n-2 . . . . . . . . Byte/Word 2 Byte/Word 1 Byte/Word 2 Byte/Word 1 . . . . Byte/Word 3 Byte/Word 2 Byte/Word 1 Byte/Word 3 n < LEN Byte/Word 3 n < LEN n < LEN Byte/Word 3 n < LEN . . . . LEN = n + 1 Byte/Word n+3 Byte/Word n+2 LEN = n + 1 Byte/Word n+3 Byte/Word n+2 LEN = n + 1 Byte/Word n+3 Byte/Word n+2 LEN = n + 1 Byte/Word n+3 Byte/Word 2 Byte/Word 1 Length = n Length = n Length = n Length = n VLEN = 001 VLEN = 010 VLEN = 011 VLEN = 100 If n LEN, LEN bytes/words are being transferred. The dotted line shows the case where LEN = n + 1 Figure 27: Variable Length Transfer Count Options 12.5.2.4 Byte or (WORDSIZE) Word Transfers Determines whether each transfer should be 8-bit (byte) or 16-bit (word). 12.5.2.5 Repeated block. On a trigger the number of byte/word transfers specified by the transfer count is performed as quickly as possible, after which the CPU is notified (DMAIRQ.DMAIFn=1) and the DMA channel is rearmed. Transfer Mode (TMODE) The transfer mode determines how the DMA channel behaves when transferring data. There are four different transfer modes. Single. On a trigger a single byte/word transfer occurs and the DMA channel awaits the next trigger. After completing the number of transfers specified by the transfer count, the CPU is notified (DMAIRQ.DMAIFn=1) and the DMA channel is disarmed. Block. On a trigger the number of byte/word transfers specified by the transfer count is performed as quickly as possible, after which the CPU is notified (DMAIRQ.DMAIFn=1) and the DMA channel is disarmed. Repeated single. On a trigger a single byte/word transfer occurs and the DMA channel awaits the next trigger. After completing the number of transfers specified by the transfer count, the CPU is notified (DMAIRQ.DMAIFn=1) and the DMA channel is rearmed. 12.5.2.6 Trigger Event (TRIG) A DMA trigger event will initiate a single byte/word transfer, a block transfer, or repeated versions of these. Each DMA channel can be set up to sense on a single trigger. The TRIG field in the configuration determines which trigger the DMA channel is to use. In addition to the configured trigger, a DMA channel can always be triggered by setting its designated DMAREQ.DMAREQn flag. The DMA trigger sources are described in Table 51 on Page 107. 12.5.2.7 Source and Destination Increment (SRCINC and DESTINC) When the DMA channel is armed or rearmed, the source and destination addresses are transferred to internal address pointers. These pointers, and hence the source and destination addresses, can be controlled to increment, decrement, or not change between byte/word transfers in order to give good SWRS033G Page 104 of 244 CC1110Fx / CC1111Fx flexibility. The possibilities increment/decrement are: for address Increment by zero. The address pointer shall remain fixed after each byte/word transfer. Increment by one. The address pointer shall increment one count after each byte/word transfer. Increment by two. The address pointer shall increment two counts after each byte/word transfer. Decrement by one. The address pointer shall decrement one count after each byte/word transfer. 12.5.2.8 Interrupt Mask (IRQMASK) configured before a DMA channel can be armed and activated. The parameters are not configured directly through SFRs, but instead they are written in a special DMA configuration data structure in memory. Each DMA channel in use requires its own DMA configuration data structure. The DMA configuration data structure consists of eight bytes and is described in Table 52. A DMA configuration data structure may reside at any location in unified memory space decided upon by the user software, and the address location is passed to the DMA controller through a set of SFRs DMAxCFGH:DMAxCFGL (x is 0 or 1). Once a channel has been armed, the DMA controller will read the configuration data structure for that channel, given by the address in DMAxCFGH:DMAxCFGL. If this bit is set to 1, the CPU interrupt flag IRCON.DMAIF=1 will be asserted when the transfer count is reached. An interrupt request is being generated if IEN1.DMAIE=1. It is important to note that the method for specifying the start address for the DMA configuration data structure differs between DMA channel 0 and DMA channels 1 - 4 as follows: 12.5.2.9 DMA0CFGH:DMA0CFGL gives the start address for DMA channel 0 configuration data structure. Mode 8 Setting (M8) When variable length transfer count is used (VLEN000 and VLEN111) this field determines whether to use seven or eight bits of the first byte in source data to determine the transfer count. This configuration is only applicable when doing byte transfers. 12.5.2.10 DMA Priority (PRIORITY) A DMA priority is associated with each DMA channel. The DMA priority is used to determine the winner in the case of multiple simultaneous internal memory requests, and whether the DMA memory access should have priority or not over a simultaneous CPU memory access. In case of an internal tie, a round-robin scheme is used to ensure access for all. There are three levels of DMA priority: DMA1CFGH:DMA1CFGL gives the start address for DMA channel 1 configuration data structure followed by channel 2 - 4 configuration data structures. This means that the DMA controller expects the DMA configuration data structures for DMA channels 1 - 4 to lie in a contiguous area in memory, starting at the address held in DMA1CFGH:DMA1CFGL and consisting of 32 bytes. 12.5.4 Aborting Transfers Ongoing byte/word transfers or armed DMA channels will be aborted using the DMAARM register to disarm the DMA channel. Low: Lowest internal priority. DMA access will always defer to a CPU access. One or more DMA channels are aborted by writing a 1 to DMAARM.ABORT register bit, and at the same time select which DMA channels to abort by setting the corresponding, DMAARM.DMAARMn bits to 1. When setting DMAARM.ABORT to 1, the DMAARM.DMAARMn bits for non-aborted channels must be written as 0. 12.5.3 An example of DMA channel arm and disarm is shown in Figure 28. High: Highest internal priority. DMA access will always prevail over CPU access. Normal: Second highest internal priority. Guarantees that DMA access prevails over CPU on at least every second try. DMA Configuration Setup The DMA channel parameters such as address mode, transfer mode and priority described in the previous section have to be SWRS033G Page 105 of 244 CC1110Fx / CC1111Fx MOV DMAARM, #0x03 MOV DMAARM, #0x81 ; Arm DMA channel 0 and 1 ; Disarm DMA channel 0, channel 1 is still armed Figure 28: DMA Arm/Disarm Example 12.5.5 DMA Interrupts 12.5.6 Each DMA channel can be configured to generate an interrupt to the CPU when the transfer count is reached. This is accomplished by setting the IRQMASK bit in the channel configuration to 1. When this bit is set to 1, IRCON.DMAIF=1 will be set to 1 when reaching the transfer count. An interrupt request is being generated if IEN1.DMAIE=1. Regardless of the IRQMASK bit in the channel configuration, DMAIRQ.DMAIFn will be set upon DMA channel complete. Thus software should always check (and clear) this register when rearming a channel with a changed IRQMASK setting. Failure to do so could generate an interrupt based on the stored interrupt flag. DMA Memory Access The byte/word transfer is affected by endian convention. This as the memory system use Big-Endian in XDATA memory, while LittleEndian is used in SFR memory. This must be accounted for in compilers. 12.5.7 DMA USB Endianess (CC1111Fx) When a USB FIFO is accessed using word transfer, the endianess of the word read/written can be controlled by setting the ENDIAN.USBWLE and ENDIAN.USBRLE configuration bits in the ENDIAN register. See Section 12.16 for details. DMA Trigger Number DMA Trigger Name Functional Unit Description 0 NONE DMA No trigger, setting DMAREQ.DMAREQx bit starts a single byte/word transfer or a block transfer 1 PREV DMA DMA channel is triggered by completion of previous channel 2 T1_CH0 Timer 1 Timer 1, capture/compare, channel 0 3 T1_CH1 Timer 1 Timer 1, capture/compare, channel 1 4 T1_CH2 Timer 1 Timer 1, capture/compare, channel 2 5 Not in use. 6 T2_OVFL Timer 2 Timer 2, timer count reaches 0x00 7 T3_CH0 Timer 3 Timer 3, compare, channel 0 8 T3_CH1 Timer 3 Timer 3, compare, channel 1 9 T4_CH0 Timer 4 Timer 4, compare, channel 0 10 T4_CH1 Timer 4 Timer 4, compare, channel 1 11 Do not use 12 IOC_0 IO Controller P0_1 input transition17 13 IOC_1 IO Controller P1_3 input transition18 14 URX0 USART0 USART0 RX complete 15 UTX0 USART0 USART0 TX complete 16 URX1 USART1 USART1 RX complete 17 UTX1 USART1 USART1 TX complete 17 18 Trigger on rising edge. P0SEL.SELP0_1 and P0DIR.P0_1 must be 0 Trigger on falling edge. P1SEL.SELP1_3 and P1DIR.P1_3 must be 0 SWRS033G Page 106 of 244 CC1110Fx / CC1111Fx DMA Trigger Number DMA Trigger Name Functional Unit Description 18 FLASH Flash Controller Flash data write complete 19 RADIO Radio RF packet byte received/transmit 20 ADC_CHALL ADC ADC end of a conversion in a sequence, sample ready 21 ADC_CH0 ADC ADC end of conversion (AIN0, single-ended or AIN0 - AIN1, differential). Sample ready 22 ADC_CH1 ADC ADC end of conversion (AIN1, single-ended or AIN0 - AIN1, differential). Sample ready 23 ADC_CH2 ADC ADC end of conversion (AIN2, single-ended or AIN2 - AIN3, differential). Sample ready 24 ADC_CH3 ADC ADC end of conversion (AIN3, single-ended or AIN2 - AIN3, differential). Sample ready 25 ADC_CH4 ADC ADC end of conversion (AIN4, single-ended or AIN4 - AIN5, differential). Sample ready 26 ADC_CH5 ADC ADC end of conversion (AIN5, single-ended or AIN4 - AIN5, differential). Sample ready ADC_CH6 ADC ADC end of conversion (AIN6, single-ended or AIN6 - AIN7, differential). Sample ready I2SRX I2S I2S RX complete ADC_CH7 ADC ADC end of conversion (AIN7, single-ended or AIN6 - AIN7, differential). Sample ready I2STX I2S I2S TX complete 29 ENC_DW AES AES encryption processor requests download input data 30 ENC_UP AES AES encryption processor requests upload output data 27 28 Table 51: DMA Trigger Sources SWRS033G Page 107 of 244 CC1110Fx / CC1111Fx Byte Offset Bit Field Name Description 0 7:0 SRCADDR[15:8] The DMA channel source address, high byte 1 7:0 SRCADDR[7:0] The DMA channel source address, low byte 2 7:0 DESTADDR[15:8] The DMA channel destination address, high byte. Note that flash memory is not directly writeable. 3 7:0 DESTADDR[7:0] The DMA channel destination address, low byte. Note that flash memory is not directly writeable. 4 7:5 VLEN[2:0] Transfer count mode. 000 Use LEN for transfer count 001 Transfer number of bytes/words commanded by n + 1 010 Transfer number of bytes/words commanded by n 011 Transfer number of bytes/words commanded by n + 2 100 Transfer number of bytes/words commanded by n + 3 101 Reserved 110 Reserved 111 Alternative for using LEN as transfer count Note: For byte size transfers (see Section 12.5.2.4), n is defined as the first byte in source data or the 7 LSB of the first byte in source data, depending on the M8 setting (see Section12.5.2.9). For word size transfers, n is the 13 LSB of the first word in source data 4 4:0 LEN[12:8] 5 7:0 LEN[7:0] This value is used as transfer count when VLEN=000 or VLEN=111 (fixed length transfer count). For all cases where VLEN000 and VLEN111 (variable length transfer count), the transfer count will be limited to LEN bytes/words when n LEN. In cases where n < LEN, the transfer count is given by the VLEN setting. 6 7 WORDSIZE Selects whether each transfer shall be 8-bit (0) or 16-bit (1). 6 6:5 TMODE[1:0] Transfer mode: 6 7 7 4:0 7:6 5:4 TRIG[4:0] SRCINC[1:0] DESTINC[1:0] 00 Single 01 Block 10 Repeated single 11 Repeated block Select DMA trigger 00000 No trigger (writing to DMAREQ is only trigger) 00001 The previous DMA channel finished 00010 11111 Selects one of the triggers shown in Table 51. The trigger is selected in the order shown in the table. Source address increment mode (after each transfer) 00 0 bytes/words 01 1 bytes/words 10 2 bytes/words 11 -1 bytes/words Destination address increment mode (after each transfer) 00 0 bytes/words 01 1 bytes/words 10 2 bytes/words 11 -1 bytes/words SWRS033G Page 108 of 244 CC1110Fx / CC1111Fx Byte Offset Bit Field Name Description 7 3 IRQMASK Interrupt Mask for this channel. 7 7 2 1:0 M8 0 Disable interrupt generation 1 Enable interrupt generation upon reaching transfer count When variable length transfer count is used (VLEN000 and VLEN111) this field determines whether to use seven or eight bits of the first byte in source data to determine the transfer count. Only applicable when WORDSIZE=0. PRIORITY[1:0] 0 Use all 8 bits 1 Use 7 LSB The DMA channel priority: 00 Low, DMA access will always defer to a CPU access 01 Normal, guarantees that DMA access prevails over CPU on at least every second try. 10 High, DMA access will always prevail over CPU access. 11 Reserved Table 52: DMA Configuration Data Structure 12.5.8 DMA Registers This section describes the SFRs associated with the DMA Controller. DMAARM (0xD6) - DMA Channel Arm Bit Field Name Reset R/W Description 7 ABORT 0 R0/W DMA abort. Ongoing byte/word transfers or armed DMA channels will be aborted when writing a 1 to this bit, and at the same time select which DMA channels to abort by setting the corresponding, DMAARM.DMAARMn bits to 1 6:5 4 DMAARM4 0 Normal operation 1 Abort channels all selected channels 0 R0 Not used 0 R/W DMA arm channel 4 This bit must be set to 1 in order for any byte/word transfers to occur on the channel. For non-repetitive transfer modes, the bit is automatically cleared when the transfer count is reached 3 DMAARM3 0 R/W DMA arm channel 3 This bit must be set to 1 in order for any byte/word transfers to occur on the channel. For non-repetitive transfer modes, the bit is automatically cleared when the transfer count is reached 2 DMAARM2 0 R/W DMA arm channel 2 This bit must be set to 1 in order for any byte/word transfers to occur on the channel. For non-repetitive transfer modes, the bit is automatically cleared when the transfer count is reached 1 DMAARM1 0 R/W DMA arm channel 1 This bit must be set to 1 in order for any byte/word transfers to occur on the channel. For non-repetitive transfer modes, the bit is automatically cleared when the transfer count is reached 0 DMAARM0 0 R/W DMA arm channel 0 This bit must be set to 1 in order for any byte/word transfers to occur on the channel. For non-repetitive transfer modes, the bit is automatically cleared when the transfer count is reached SWRS033G Page 109 of 244 CC1110Fx / CC1111Fx DMAREQ (0xD7) - DMA Channel Start Request and Status Bit Field Name 7:5 4 DMAREQ4 Reset R/W Description 000 R0 Not used 0 R/W1 H0 DMA channel 4, manual trigger Setting this bit to 1 will have the same effect as a single trigger event. This bit is cleared when the DMA channel is granted access. 3 DMAREQ3 0 R/W1 H0 DMA channel 3, manual trigger Setting this bit to 1 will have the same effect as a single trigger event. This bit is cleared when the DMA channel is granted access. 2 DMAREQ2 0 R/W1 H0 DMA channel 2, manual trigger Setting this bit to 1 will have the same effect as a single trigger event. This bit is cleared when the DMA channel is granted access. 1 DMAREQ1 0 R/W1 H0 DMA channel 1, manual trigger Setting this bit to 1 will have the same effect as a single trigger event. This bit is cleared when the DMA channel is granted access. 0 DMAREQ0 0 R/W1 H0 DMA channel 0, manual trigger Setting this bit to 1 will have the same effect as a single trigger event. This bit is cleared when the DMA channel is granted access. DMA0CFGH (0xD5) - DMA Channel 0 Configuration Address High Byte Bit Field Name Reset R/W Description 7:0 DMA0CFG[15:8] 0x00 R/W The DMA channel 0 configuration address, high byte DMA0CFGL (0xD4) - DMA Channel 0 Configuration Address Low Byte Bit Field Name Reset R/W Description 7:0 DMA0CFG[7:0] 0x00 R/W The DMA channel 0 configuration address, low byte DMA1CFGH (0xD3) - DMA Channel 1 - 4 Configuration Address High Byte Bit Field Name Reset R/W Description 7:0 DMA1CFG[15:8] 0x00 R/W The DMA channel 1 - 4 configuration address, high byte DMA1CFGL (0xD2) - DMA Channel 1 - 4 Configuration Address Low Byte Bit Field Name Reset R/W Description 7:0 DMA1CFG[7:0] 0x00 R/W The DMA channel 1 - 4 configuration address, low byte SWRS033G Page 110 of 244 CC1110Fx / CC1111Fx DMAIRQ (0xD1) - DMA Interrupt Flag Bit Field Name 7:5 4 3 2 1 0 DMAIF4 DMAIF3 DMAIF2 DMAIF1 DMAIF0 Reset R/W Description 0 R0 Not used 0 R/W0 DMA channel 4 interrupt flag. 0 0 0 0 R/W0 R/W0 R/W0 R/W0 0 Transfer count not reached 1 Transfer count reached/interrupt pending DMA channel 3 interrupt flag. 0 Transfer count not reached 1 Transfer count reached/interrupt pending DMA channel 2 interrupt flag. 0 Transfer count not reached 1 Transfer count reached/interrupt pending DMA channel 1 interrupt flag. 0 Transfer count not reached 1 Transfer count reached/interrupt pending DMA channel 0 interrupt flag. 0 Transfer count not reached 1 Transfer count reached/interrupt pending ENDIAN (0x95) - USB Endianess Control (CC1111Fx) Bit Field Name 7:2 1 0 USBWLE USBRLE Reset R/W Description 0 R/W Not used 0 R/W USB Write Endianess setting for DMA channel word transfers to USB. 0 R/W 0 Big Endian 1 Little Endian USB Read Endianess setting for DMA channel word transfers from USB. 0 Big Endian 1 Little Endian SWRS033G Page 111 of 244 CC1110Fx / CC1111Fx 12.6 16-bit Timer, Timer 1 Timer 1 is an independent 16-bit timer which supports typical timer/counter functions such as input capture, output compare, and PWM functions. The timer has three independent capture/compare channels and uses one I/O pin per channel. The features of Timer 1 are as follows: Three capture/compare channels Rising, falling, or any edge input capture Set, clear, or toggle output compare Free-running, modulo counter operation or up/down Clock prescaler for divide by 1, 8, 32, or 128 Interrupt request generation on capture/compare and when reaching the terminal count value Capture triggered by radio The counter operates as either a free-running counter, a modulo counter, or as an up/down counter for use in centre-aligned PWM. It can also be used in DSM mode. It is possible to read the 16-bit counter value through the two 8-bit SFRs; T1CNTH and T1CNTL, containing the high-order byte and low-order byte respectively. When the T1CNTL register is read, the high-order byte of the counter at that instant is buffered in T1CNTH so that the high-order byte can be read from T1CNTH. Thus T1CNTL shall always be read first before reading T1CNTH. All write accesses to the T1CNTL register will reset the 16-bit counter. The counter may produce an interrupt request when the terminal count value (overflow) is reached (see Section 12.6.2.1 - 12.6.2.3). It is possible to start and halt the counter with T1CTL control register settings. The counter is started when a value other than 00 is written to T1CTL.MODE. If 00 is written to T1CTL.MODE the counter halts at its present value. DMA trigger function Delta-Sigma Modulator (DSM) mode Note: In the following sections, an n in the register name represent the channel number 0, 1, or 2 if nothing else is stated 12.6.1 used as system clock source, the highest clock frequency used by Timer 1 is fXOSC/2 for CC1110Fx and 12 MHz for CC1111Fx, given that the HS RCOSC has been calibrated. 12.6.2 16-bit Timer Counter The timer consists of a 16-bit counter that increments or decrements at each active clock edge. The frequency of the active clock edges is given by CLKCON.TICKSPD and T1CTL.DIV. CLKCON.TICKSPD is used to set the timer tick speed. The timer tick speed will vary from 203.125 kHz to 26 MHz for CC1110Fx and 187.5 kHz to 24 MHz for CC1111Fx (given the use of a 26 MHz or 48 MHz crystal respectively). Note that the clock speed of the system clock is not affected by the TICKSPD setting. The timer tick speed is further divided in Timer 1 by the prescaler value set by T1CTL.DIV. This prescaler value can be 1, 8, 32, or 128. Thus the lowest clock frequency used by Timer 1 is 1.587 kHz and the highest is 26 MHz when a 26 MHz crystal oscillator is used as system clock source (CC1110Fx). The lowest clock frequency used by Timer 1 is 1.465 kHz and the highest is 24 MHz for CC1111Fx. When the high speed RC oscillator is Timer 1 Operation In general, the control register T1CTL is used to control the timer operation. The various modes of operation are described in the following three sections. 12.6.2.1 Free-running Mode In free-running mode the counter starts from 0x0000 and increments at each active clock edge. When the counter reaches the terminal count value 0xFFFF (overflow), the counter is loaded with 0x0000 on the next timer tick and continues incrementing its value as shown in Figure 29. When 0xFFFF is reached, the T1CTL.OVFIF flag is set. The IRCON.T1IF flag is only asserted if the corresponding interrupt mask bit TIMIF.OVFIM is set. An interrupt request is generated when both TIMIF.OVFIM and IEN1.T1EN are set to 1. The free-running mode can be used to generate independent time intervals and output signal frequencies. SWRS033G Page 112 of 244 CC1110Fx / CC1111Fx 0xFFFF 0x0000 OVFIF = 1 OVFIF = 1 Figure 29: Free-running Mode 12.6.2.2 Modulo Mode T1CTL.OVFIF flag is set. The IRCON.T1IF flag is only asserted if the corresponding interrupt mask bit TIMIF.OVFIM is set. An interrupt request is generated when both TIMIF.OVFIM and IEN1.T1EN are set to 1. The modulo mode can be used for applications where a period other than 0xFFFF is required. In modulo mode the counter starts from 0x0000 and increments at each active clock edge. When the counter reaches the terminal count value T1CC0 (overflow), held in the registers T1CC0H:T1CC0L, the counter is loaded with 0x0000 on the next timer tick and continues incrementing its value as shown in Figure 30. When T1CC0 is reached, the T1CC0 0x0000 OVFIF = 1 OVFIF = 1 Figure 30: Modulo Mode 12.6.2.3 Up/Down Mode In up/down mode the counter starts from 0x0000 and increments at each active clock edge. When the counter value matches the terminal count value T1CC0, held in the registers T1CC0H:T1CC0L, the counter counts down until 0x0000 is reached and it starts counting up again as shown in Figure 31. When 0x0000 is reached, the T1CTL.OVFIF flag is set. The IRCON.T1IF flag is only asserted if the corresponding interrupt mask bit TIMIF.OVFIM is set. An interrupt request is generated when both TIMIF.OVFIM and IEN1.T1EN are set to 1. The up/down mode can be used when symmetrical output pulses are required with a period other than 0xFFFF, and therefore allows implementation of centrealigned PWM output applications. Figure 31: Up/Down Mode 12.6.3 Channel Mode Control The channel mode is set with each channel's control and status register T1CCTLn. The settings include input capture and output compare modes. Note: Before an I/O pin can be used by the timer, the required I/O pin must be configured as a Timer 1 peripheral pin as described in Section 12.4.6 on Page 91 . SWRS033G Page 113 of 244 CC1110Fx / CC1111Fx 12.6.4 Input Capture Mode When a channel is configured as an input capture channel, the I/O pin associated with that channel, is configured as an input. After the timer has been started, a rising edge, falling edge or any edge on the input pin will trigger a capture of the 16-bit counter contents into the associated capture register. Thus the timer is able to capture the time when an external event takes place. The channel input pin is synchronized to the internal system clock. Thus pulses on the input pin must have a minimum duration greater than the system clock period. The contents of the 16-bit capture register can be read from registers T1CCnH:T1CCnL. When the capture takes place, the interrupt flag for the appropriate channel (T1CTL.CH0IF, T1CTL.CH1IF, or T1CTL.CH2IF for channel 0, 1, and 2 respectively) is asserted. The IRCON.T1IF flag is only asserted if the corresponding interrupt mask bit T1CCTL0.IM, T1CCTL1.IM, or T1CCTL2.IM is set to 1. An interrupt request is generated if the corresponding interrupt mask bit is set together with IEN1.T1EN. 12.6.4.1 RF Event Capture Each timer channel may be configured so that the RF events associated with the RF interrupt (interrupt #16) will trigger a capture instead of the normal input pin capture. This is done by setting T1CCTLn.CPSEL=1. When this configuration is chosen, the RF event(s) enabled by RFIM (see Section 13.3.1 on Page 187) will trigger a capture. This way the timer can be used to capture a value when e.g. a start of frame delimiter (SFD) is detected. Note: When using an RF event to trigger a capture, both CLKCON.CLKSPD and CLKCON.TICKSPD must be set to 000. 12.6.5 Output Compare Mode In output compare mode the I/O pin associated with a channel is set as an output. After the timer has been started, the contents of the counter are compared with the contents of the channel compare register T1CCnH:T1CCnL. If the compare register equals the counter contents, the output pin is set, reset, or toggled according to the compare output mode setting of T1CCTLn.CMP. Note that all edges on output pins are glitch-free when operating in a given output compare mode. Writing to the compare register T1CCnL is buffered so that a value written to T1CCnL does not take effect until the corresponding high order register, T1CCnH is written. For output compare modes 0 - 2, a new value written to the compare register T1CCnH:T1CCnL takes effect after the registers have been written. For other output compare modes the new value written to the compare register takes effect when the timer reaches 0x0000. Note that channel 0 has fewer output compare modes than channel 1 and 2 because T1CC0H:T1CC0L has a special function in modes 5 and 6, meaning these modes would not be useful for channel 0. When a compare occurs, the interrupt flag for the appropriate channel (T1CTL.CH0IF, T1CTL.CH1IF, or T1CTL.CH2IF for channel 0, 1, and 2 respectively) is asserted. The IRCON.T1IF flag is only asserted if the corresponding interrupt mask bit T1CCTL0.IM, T1CCTL1.IM, or T1CCTL2.IM is set to 1. An interrupt request is generated if the corresponding interrupt mask bit is set together with IEN1.T1EN. When operating in up-down mode, the interrupt flag for channel 0 is set when the counter reaches 0x0000 instead of when a compare occurs. Examples of output compare modes in various timer modes are given in Figure 32, Figure 33, and Figure 34. Edge-aligned: PWM output signals can be generated using the timer modulo mode and channels 1 and 2 in output compare mode 5 or 6 (defined by T1CCTLn.CMP bits, where n is 1 or 2) as shown in Figure 33. The period of the PWM signal is determined by the setting in T1CC0 and the duty cycle is determined by T1CCn. PWM output signals can also be generated using the timer free-running mode and channels 1 and 2 in output compare mode 5 or 6 as shown in Figure 32. In this case the period of the PWM signal is determined by CLKCON.TICKSPD and the prescaler divider value in T1CTL.DIV and the duty cycle is determined by T1CCn (n = 1 or 2). The polarity of the PWM signal is determined by whether output compare mode 5 or 6 is used. For both modulo mode and free-running mode it is also possible to use compare mode 3 or 4 to generate a PWM output signal (see Figure 32 and Figure 33). SWRS033G Page 114 of 244 CC1110Fx / CC1111Fx The polarity of the PWM signal is determined by whether output compare mode 3 or 4 is used. Centre-aligned: PWM outputs can be generated when the timer up/down mode is selected. The channel output compare mode 3 or 4 (defined by T1CCTLn.CMP bits, where n is 1 or 2) is selected depending on required polarity of the PWM signal (see Figure 34). The period of the PWM signal is determined by T1CC0 and the duty cycle for the channel output is determined by T1CCn (n = 1 or 2). 0xFFFF T1CC0 T1CCn 0x0000 0: Set output on compare 1: Clear output on compare 2: Toggle output on compare 3: Set output on compare-up, clear on 0 4: Clear output on compare-up, set on 0 5: Set when T1CCn, clear when T1CC0 6: Clear when T1CCn, set when T1CC0 T1CCn T1CC0 T1CCn T1CC0 Figure 32: Output Compare Modes, Timer Free-running Mode SWRS033G Page 115 of 244 CC1110Fx / CC1111Fx T1CC0 T1CCn 0x0000 0: Set output on compare 1: Clear output on compare 2: Toggle output on compare 3: Set output on compare-up, clear on 0 4: Clear output on compare-up, set on 0 5: Set when T1CCn, clear when T1CC0 6: Clear when T1CCn, set when T1CC0 T1CCn T1CC0 T1CCn T1CC0 Figure 33: Output Compare Modes, Timer Modulo Mode SWRS033G Page 116 of 244 CC1110Fx / CC1111Fx T1CC0 T1CCn 0x0000 0: Set output on compare 1: Clear output on compare 2: Toggle output on compare 3: Set output on compare-up, clear on compare down 4: Clear output on compare-up, set on compare-down 5: Set when T1CCn, clear when T1CC0 6: Clear when T1CCn, set when T1CC0 T1CCn T1CC0 T1CCn T1CCn T1CC0 T1CCn Figure 34: Output Modes, Timer Up/Down Mode 12.6.6 Timer 1 Interrupts There is one interrupt vector assigned to the timer. This is T1 (Interrupt #9, see Table 39). The following timer events may generate an interrupt request: Counter reaches terminal count value (overflow) or turns around on zero Input capture event Output compare event The register bits T1CTL.OVFIF, T1CTL.CH0IF, T1CTL.CH1IF, and T1CTL.CH2IF contains the interrupt flags for the terminal count value event (overflow), and the three channel compare/capture events, respectively. These flags will be asserted regardless off the channel n interrupt mask bit (T1CCTLn.IM). The CPU interrupt flag, IRCON.T1IF will only be asserted if one or more of the channel n interrupt mask bits are set to 1. An interrupt request is only generated when the corresponding interrupt mask bit is SWRS033G Page 117 of 244 CC1110Fx / CC1111Fx set together with IEN1.T1EN. The interrupt mask bits are T1CCTL0.IM, T1CCTL1.IM, T1CCTL2.IM, and TIMIF.OVFIM. Note that enabling an interrupt mask bit will generate a new interrupt request if the corresponding interrupt flag is set. When the timer is used in Free-running Mode or Modulo Mode the interrupt flags are set as follows: T1CTL.CH0IF, T1CTL.CH1IF, T1CTL.CH2IF are set compare/capture event and on T1CTL.OVFIF is set when counter reaches terminal count value (overflow) When the timer is used in Up/Down Mode the interrupt flags are set as follows: In compare mode: T1CTL.CH0IF and T1CTL.OVFIF are set when counter turns around on zero T1CTL.CH1IF and T1CTL.CH2IF are set on compare event In capture mode: T1CTL.OVFIF is set when counter turns around on zero T1CTL.CH0IF, T1CTL.CH1IF, and T1CTL.CH2IF are set on capture event I addition, the CPU interrupt flag, IRCON.T1IF will be asserted if the channel n interrupt mask bit (T1CCTLn.IM) is set to 1. 12.6.7 Timer 1 DMA Triggers There are three DMA triggers associated with Timer 1, one for each channel. These are DMA triggers T1_CH0, T1_CH1 and T1_CH2, which are generated on timer capture/compare events as follows: T1_CH0 - Channel 0 capture/compare T1_CH1 - Channel 1 capture/compare T1_CH2 - Channel 2 capture/compare 12.6.8 DSM Mode Timer 1 also contains a 1-bit Delta-Sigma Modulator (DSM) of second order that can be used to produce a mono audio output PWM signal. The DSM removes the need for high order external filtering required when using regular PWM mode. The DSM operates at a fixed speed of either 1/4 or 1/8 of the timer tick speed set by CLKCON.TICKSPD. The DSM speed is set by T1CCTL1.MODE. The input samples are updated at a configurable sampling rate set by the terminal count value T1CC0. An interpolator is used to match the sampling rate with the DSM update rate. This interpolator is of first order with a scaling compensation. The scaling compensation is due to variable gain defined by the difference in sampling speed and DSM speed. This interpolation mechanism can be disabled by setting T1CCTL1.CAP=10 or T1CCTL1.CAP=11, thus using a zeroth order interpolator. In addition to the interpolator, a shaper can be used to account for differences in rise/fall times in the output signal. Also the shaper is enabled/disabled using the two CAP bits in the T1CCTL1 register. This shaper ensures a rising and a falling edge per bit and will thus limit the output swing to 1/8 to 7/8 of I/O VDD when the DSM operates at 1/8 of the timer tick speed or 1/4 to 3/4 of I/O VDD when the DSM operates at 1/4 of the timer tick speed. The DSM is used as in PWM mode where the terminal count value T1CC0 defines the period/sampling rate. The DSM can not use the Timer 1 prescaler to further slow down the period. Timer 1 must be configured to operate in modulo mode (T1CTL.MODE=10) and channel 0 must be configured to compare mode (T1CCTL0.MODE=1). The terminal count value T1CC0, held in the registers T1CC0H:T1CC0L, defines the sample rate. Table 53 shows some T1CC0 settings for different sample rates (CLKCON.TICKSPD=000). SWRS033G Page 118 of 244 CC1110Fx / CC1111Fx Sample Rate T1CC0H T1CC0L 8 kHz @ 24 MHz 0x0B 0xB7 8 kHz @ 26 MHz 0x0C 0xB1 16 kHz @ 24 MHz 0x05 0xDB 16 kHz @ 26 MHz 0x06 0x59 48 kHz @ 24 MHz 0x01 0xF3 48 kHz @ 26 MHz 0x02 0x1D 64 kHz @ 24 MHz 0x01 0x76 64 kHz @ 26 MHz 0x01 0x96 Table 53: Channel 0 Period Setting for some Sampling Rates (CLKCON.TICKSPD=000) Since the DSM starts immediately after DSM mode has been enabled by setting T1CCTL1.CMP=111, all configuration should have been performed prior to enabling DSM mode. Also, the Timer 1 counter should be cleared and started just before starting the DSM operation (all write accesses to the T1CNTL register will reset the 16-bit counter while writing a value other than 00 to T1CTL.MODE will start the counter). A simple procedure for setting up DSM mode should then be as follows: 1. Suspend timer 1 (T1CTL.MODE=00) 2. Clear timer counter by writing any value to T1CNTL, (CNT=0x0000) On each Timer 1 IRQ or Timer 1 DMA trigger, write a new sample to the T1CC1H:T1CC1L registers. The least significant bits must be written to T1CC1L before the most significant bits are written to T1CC1H. The samples written must be signed 2's complement values. The 2 least significant bits will always be treated as 0, thus the effective sample size is 14 bits. 12.6.9 Timer 1 Registers This section describes the following Timer 1 registers: T1CNTH - Timer 1 Counter High 3. Set the sample rate by writing to T1CC0. T1CNTL - Timer 1 Counter Low 4. Set Timer 1 channel 0 compare mode (T1CCTL0.MODE=1) T1CTL - Timer 1 Control and Status T1CCTLn - Timer 1 Capture/Compare Control 5. Load first sample if available (or zero if no sample available) into T1CC1H:T1CC1L. 6. Set timer operation to modulo mode (T1CTL.MODE=10) 7. Configure the DSM by setting the MODE and CAP fields of the T1CCTL1 register. 8. Enable DSM (T1CCTL1.CMP=111) mode Channel n T1CCnH - Timer 1 Channel Capture/Compare Value High n T1CCnL Timer 1 Channel Capture/Compare Value Low n The TIMIF register is described in Section 12.9.8. SWRS033G Page 119 of 244 CC1110Fx / CC1111Fx T1CNTH (0xE3) - Timer 1 Counter High Bit Field Name Reset R/W Description 7:0 CNT[15:8] 0x00 R Timer count high order byte. Contains the high byte of the 16-bit timer counter buffered at the time T1CNTL is read. T1CNTL (0xE2) - Timer 1 Counter Low Bit Field Name Reset R/W Description 7:0 CNT[7:0] 0x00 R/W Timer count low order byte. Contains the low byte of the 16-bit timer counter. Writing anything to this register results in the counter being cleared to 0x0000. T1CTL (0xE4) - Timer 1 Control and Status Bit Field Name Reset R/W Description 7 CH2IF 0 R/W 0 Timer 1 channel 2 interrupt flag 6 5 4 3:2 CH1IF CH0IF OVFIF DIV[1:0] 0 0 0 00 R/W 0 R/W 0 R/W 0 R/W 0 No interrupt pending 1 Interrupt pending Timer 1 channel 1 interrupt flag 0 No interrupt pending 1 Interrupt pending Timer 1 channel 0 interrupt flag 0 No interrupt pending 1 Interrupt pending Timer 1 counter overflow interrupt flag. Set when the counter reaches the terminal count value in free-running or modulo mode or when counter turns around on zero in up/down mode 0 No interrupt pending 1 Interrupt pending Prescaler divider value. Generates the active clock edge used to update the counter as follows: 00 Tick frequency/1 01 Tick frequency/8 10 Tick frequency/32 11 Tick frequency/128 Note: The prescaler counter is not reset when writing these bits, hence one prescaler period may be needed before updated data is used. 1:0 MODE[1:0] 00 R/W Timer 1 mode select. The timer operating mode is selected as follows: 00 Operation is suspended 01 Free-running, repeatedly count from 0x0000 to 0xFFFF 10 Modulo, repeatedly count from 0x0000 to T1CC0 11 Up/down, repeatedly count from 0x0000 to T1CC0 and from T1CC0 down to 0x0000 SWRS033G Page 120 of 244 CC1110Fx / CC1111Fx T1CCTL0 (0xE5) - Timer 1 Channel 0 Capture/Compare Control Bit Field Name Reset R/W Description 7 CPSEL 0 R/W Timer 1 channel 0 capture select 6 5:3 2 1:0 IM CMP[2:0] MODE CAP[1:0] 1 000 0 00 R/W R/W R/W R/W 0 Use normal capture input 1 Use RF event(s) enabled in the RFIM register to trigger a capture Channel 0 interrupt mask 0 Interrupt disabled 1 Interrupt enabled Channel 0 compare mode select. Selects action on output when timer value equals compare value in T1CC0 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Reserved 110 Reserved 111 Reserved Mode. Select Timer 1 channel 0 capture or compare mode 0 Capture mode 1 Compare mode Channel 0 capture mode select 00 No capture 01 Capture on rising edge 10 Capture on falling edge 11 Capture on both edges T1CC0H (0xDB) - Timer 1 Channel 0 Capture/Compare Value High Bit Field Name Reset R/W Description 7:0 T1CC0[15:8] 0x00 R/W Timer 1 channel 0 capture/compare value, high order byte. Set the DSM sample rate in DSM mode T1CC0L (0xDA) - Timer 1 Channel 0 Capture/Compare Value Low Bit Field Name Reset R/W Description 7:0 T1CC0[7:0] 0x00 R/W Timer 1 channel 0 capture/compare value, low order byte Set the DSM sample rate in DSM mode SWRS033G Page 121 of 244 CC1110Fx / CC1111Fx T1CCTL1 (0xE6) - Timer 1 Channel 1 Capture/Compare Control Bit Field Name Reset R/W Description 7 CPSEL 0 R/W Timer 1 channel 1 capture select 6 5:3 2 1:0 IM CMP[2:0] MODE CAP[1:0] 1 000 0 00 R/W R/W R/W 0 Use normal capture input 1 Use RF event(s) enabled in the RFIM register to trigger a capture Channel 1 interrupt mask 0 Interrupt disabled 1 Interrupt enabled Channel 1 compare mode select. Selects action on output when timer value equals compare value in T1CC1 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set when equal to T1CC1, clear when equal to T1CC0 110 Clear when equal to T1CC1, set when equal to T1CC0 111 DSM mode enable CMP 111 CMP = 111 Select Timer 1 channel 1 capture or compare mode Set the DSM speed 0 Capture mode 1/8 of timer tick speed 1 Compare mode 1/4 of timer tick speed Channel 1 capture mode select (timer mode) DSM interpolator and output shaping configuration (DSM mode) 00 No capture DSM interpolator and output shaping enabled 01 Capture on rising edge DSM interpolator enabled and output shaping disabled 10 Capture on falling edge DSM interpolator disabled and output shaping enabled 11 Capture on both edges DSM interpolator and output shaping disabled R/W T1CC1H (0xDD) - Timer 1 Channel 1 Capture/Compare Value High Bit Field Name Reset R/W Description 7:0 T1CC1[15:8] 0x00 R/W Timer 1 channel 1 capture/compare value, high order byte DSM data high order byte (DSM mode) T1CC1L (0xDC) - Timer 1 Channel 1 Capture/Compare Value Low Bit Field Name Reset R/W Description 7:0 T1CC1[7:0] 0x00 R/W Timer 1 channel 1 capture/compare value, low order byte DSM data low order byte. The two least significant bits are not used. (DSM mode) SWRS033G Page 122 of 244 CC1110Fx / CC1111Fx T1CCTL2 (0xE7) - Timer 1 Channel 2 Capture/Compare Control Bit Field Name Reset R/W Description 7 CPSEL 0 R/W Timer 1 channel 2 capture select 6 5:3 2 1:0 IM CMP[2:0] MODE CAP[1:0] 1 000 0 00 R/W R/W R/W R/W 0 Use normal capture input 1 Use RF event(s) enabled in the RFIM register to trigger a capture Channel 2 interrupt mask 0 Interrupt disabled 1 Interrupt enabled Channel 2 compare mode select. Selects action on output when timer value equals compare value in T1CC2 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set when equal to T1CC2, clear when equal to T1CC0 110 Clear when equal to T1CC2, set when equal to T1CC0 111 Not used Mode. Select Timer 1 channel 2 capture or compare mode 0 Capture mode 1 Compare mode Channel 2 capture mode select 00 No capture 01 Capture on rising edge 10 Capture on falling edge 11 Capture on both edges T1CC2H (0xDF) - Timer 1 Channel 2 Capture/Compare Value High Bit Field Name Reset R/W Description 7:0 T1CC2[15:8] 0x00 R/W Timer 1 channel 2 capture/compare value, high order byte T1CC2L (0xDE) - Timer 1 Channel 2 Capture/Compare Value Low Bit Field Name Reset R/W Description 7:0 T1CC2[7:0] 0x00 R/W Timer 1 channel 2 capture/compare value, low order byte SWRS033G Page 123 of 244 CC1110Fx / CC1111Fx 12.7 MAC Timer (Timer 2) The MAC timer is designed for slot timing operations used by the MAC layer in an RF protocol. The timer includes a highly tunable prescaler allowing the user to select a timer interval that equals, or is an integer fraction of, a transmission slot. 8-bit timer the 18 bit counter and thus set the maximum value. The timer 2 interval / time slot, T, can be given as: T = T2PR Val(T2CTL.TIP)/ timer tick speed, where the function Val(x) is set by T2CTL.TIP and defined as 18-bit tunable prescaler Val(00) = 64 12.7.1 Timer Operation Val(01) = 128 This section describes the operation of the timer. The timer count can be read from the T2CT SFR. At each active clock edge, the timer count is decremented by one. When the timer count reaches 0x00, the register bit T2CTL.TEX is set to 1. When T2CTL.TIG=0, the timer will not wrap around when the timer count reaches 0x00. When T2CTL.TIG=1, timer count will wrap around and start counting down from 0xFF. If T2CTL.INT=1, IRCON.T2IF will also be asserted when T2CTL.TEX is set to 1. An interrupt request will be generated if both T2CTL.INT and IEN1.T2IE are set to 1. When a new value is written to the timer count register, T2CT, this value is stored in the counter immediately. If an active clock edge and a write to T2CT occur at the same time, the written value will be decremented before it is stored. Val(10) = 256 Val(11) = 1024 Example: T2PR = 0x09 T2CTL.TIP = 10 CLKCON.TICKSPD = 101 (812.5 kHz @ when fxosc = 26 MHz) -3 T = 9 256 / 812.5 kHz = 2.84 10 s 12.7.2 Timer 2 DMA Trigger There is one DMA trigger associated with Timer 2. This is the DMA trigger T2_OVFL, which is generated when T2CTL.TEX is set to 1. 12.7.3 Timer 2 Registers The SFRs associated with Timer 2 are listed in this section. These registers are the following: The 18 bit prescaler is controlled by: T2CTL - Timer 2 Control T2PR - Timer 2 Prescaler T2CT - Timer 2 Count Timer tick speed (CLKCON.TICKSPD) T2CTL.TIP Prescaler value (T2PR) All events in timer 2 are aligned to timer tick speed given by CLKCON.TICKSPD. T2CTL.TIP defines how fast the prescaler counter counts up towards its maximum value where it is reset and starts over again. The prescaler value, T2PR, defines the 8 MSB of SWRS033G Note: These registers will be in their reset state when returning to active mode from PM2 and PM3. Page 124 of 244 CC1110Fx / CC1111Fx T2CTL (0x9E) - Timer 2 Control Bit Field Name 7 6 TEX 5 4 INT 3 2 1:0 TIG TIP[1:0] Reset R/W Description 0 R/W 0 Reserved 0 R/W 0 This bit is set to 1 when the timer count reaches 0x00. Writing a 1 to this bit has no effect 0 R/W Reserved. Always set to 0. 0 R/W Timer 2 Interrupt enable 0 Interrupt disable 1 Interrupt enable 0 R/W Reserved. Always set to 0 0 R/W Tick generator mode 00 R/W 0 Tick generator is running when T2CT not equal to 0x00. The tick generator will always start running form its null state. 1 Tick generator is in free-running mode. If it is not already running it will start from its null state when this bit is set to 1 This value is used to calculate the timer 2 interval / time slot, T T = T2PR Val(T2CTL.TIP)/ timer tick speed, 00 64 01 128 10 256 11 1024 T2CT (0x9C) - Timer 2 Count Bit Field Name Reset R/W Description 7:0 CNT[7:0] 0x00 R/W Timer count. Contents of 8-bit counter. T2PR (0x9D) - Timer 2 Prescaler Bit Field Name Reset R/W Description 7:0 PR[7:0] 0x00 R/W Timer prescaler multiplier. 0x00 is interpreted as 256 SWRS033G Page 125 of 244 CC1110Fx / CC1111Fx 12.8 Sleep Timer The Sleep Timer is used to control when the CC1110Fx/CC1111Fx exits from PM{0 - 2} and hence the Sleep Timer can be used to implement a wake up functionality which enables CC1110Fx/CC1111Fx to periodically wake up to active mode and listen for incoming RF packets. Note: The Sleep timer should not be used in active mode 12.8.1 given by WOREVT1.EVENT0 and WOREVT0.EVENT0, and an exponent value set by WORCTRL.WOR_RES. When using the low power RC oscillator to clock the Sleep Timer, tEvent0 is given by: t Event 0 750 EVENT 0 2 5WOR _ RES f ref If the 32.768 kHz crystal oscillator is used to clock the Sleep Timer, tEvent0 is calculated as follows: Sleep Timer Operation t Event 0 This section describes the operation of the timer. 1 EVENT 0 25WOR _ RES 32768 The time from the CC1110Fx/CC1111Fx enters PM2 until the next Event 0 is programmed to appear (tSLEEPmin) should be larger than 11.08 ms when fref is 26 MHz and 12 ms when fref is 24 MHz (Sleep Timer clocked by the low power RC oscillator). Note: In this section of the document, fRef is used to denote the reference frequency for the synthesizer. For CC1110Fx freffXOSCand for CC1111Fx, f ref f XOSC 2 When referring to the low power RCOSC, calibrated values are assumed t SLEEPmin The Sleep Timer consists of a 31-bit counter. The appropriate bits of this counter are selected according to a resolution setting determined by the WORCTRL.WOR_RES register bits. The Sleep Timer is either clocked by the 32.768 kHz crystal oscillator or by the low power RC oscillator (fref / 750). The timer can only be used in PM0, PM1, and PM2. The Sleep Timer has a programmable timing event called Event 0. While in PM0, PM1, or PM2, reaching Event 0 will make the CC1110Fx/CC1111Fx enter active mode. The time between two consecutive Event 0's (tEvent0) is programmed with a mantissa value 750 384 f ref When the Sleep Timer is clocked by the 32.768 kHz crystal oscillator, tSLEEPmin = 11.72 ms (384/32768). 12.8.2 Sleep Timer and Power Modes Entering PM{0 - 2} and/or updating EVENT0 and has to be aligned to a positive edge on the 32 kHz clock source. The following code examples should be used in order to update EVENT0 and/or entering PM{0 - 2} correctly: Please note that the update rate of the WORTIME0 register will depend on the Sleep Timer resolution, configured through WORCTRL.WOR_RES. // Alignment of entering PM{0 - 2} to a positive edge on the 32 kHz clock source char temp = WORTIME0; while(temp == WORTIME0); // Wait until a positive 32 kHz edge PCON |= 0x01; // Enter PM{0 - 2} // Alignment of updating EVENT0 to a positive edge on the 32 kHz clock source char temp = WORTIME0; while(temp == WORTIME0); // Wait until a positive 32 kHz edge WOREVT1 = desired event0 >> 8; // Set EVENT0, high byte WOREVT0 = desired event0; // Set EVENT0, low byte // Alignment of both updating EVENT0 // on the 32 kHz clock source char temp = WORTIME0; while(temp == WORTIME0); WOREVT1 = desired event0 >> 8; WOREVT0 = desired event0; PCON |= 0x01; and entering PM{0 - 2}to a positive edge // // // // Wait until a positive 32 kHz edge Set EVENT0, high byte Set EVENT0, low byte Enter PM{0 - 2} SWRS033G Page 126 of 244 CC1110Fx / CC1111Fx If EVENT0 is changed to a value lower than the current counter value, WORCTRL.WOR_RESET has to be asserted first to reset the timer. The assertion of WORCTRL.WOR_RESET must be // Reset timer and enter PM{0 - 2} WORCTRL |= 0x04; char temp = WORTIME0; while(temp == WORTIME0); temp = WORTIME0; while(temp == WORTIME0); PCON |= 0x01; // Reset timer and update EVENT0 WORCTRL |= 0x04; char temp = WORTIME0; while(temp == WORTIME0); temp = WORTIME0; while(temp == WORTIME0); WOREVT1 = desired event0 >> 8; WOREVT0 = desired event0; followed by two positive edges on the 32 kHz clock source. The code below shows how to reset the Sleep Timer in combination with updating EVENT0 and/or entering PM{0 - 2}. // Reset Sleep Timer // Wait until a positive 32 kHz edge // Wait until a positive 32 kHz edge // Enter PM{0 - 2} // Reset Sleep Timer // Wait until a positive 32 kHz edge // Wait until a positive 32 kHz edge // Set EVENT0, high byte // Set EVENT0, low byte // Reset timer, update EVENT0, and enter PM{0 - 2} WORCTRL |= 0x04; // Reset Sleep Timer char temp = WORTIME0; while(temp == WORTIME0); // Wait until a positive 32 kHz edge temp = WORTIME0; while(temp == WORTIME0); // Wait until a positive 32 kHz edge WOREVT1 = desired event0 >> 8; // Set EVENT0, high byte WOREVT0 = desired event0; // Set EVENT0, low byte PCON |= 0x01; // Enter PM{0 - 2} 12.8.3 Low Power RC Oscillator and Timing This section applies to using the low power RC oscillator as clock source for the Sleep Timer. The frequency of the low-power RC oscillator, which can be used as clock source for the Sleep Timer, varies with temperature and supply voltage. In order to keep the frequency as accurate as possible, the RC oscillator will be calibrated whenever possible, which is when the high speed crystal oscillator is running and the chip is in active mode or PM0. When the chip goes to PM1 or PM2, the RC oscillator will use the last valid calibration result. The frequency of the low power RC oscillator is therefore locked to fref / 750. 12.8.4 Sleep Timer Interrupt the corresponding mask bit, EVENT0_MASK, is set in the WORIRQ register, the CPU interrupt flag IRCON.STIF will also be asserted in addition to the interrupt flag in WORIRQ. If IEN0.STIE=1 when IRCON.STIF is asserted, and ST interrupt request will be generated. Note: All port interrupts are blocked when SLEEP.MODE00 12.8.5 There is one DMA trigger associated with the Sleep Timer. This is the DMA trigger ST, which is generated when Event 0 occurs. 12.8.6 When Event 0 occurs, the WORIRQ.EVENT0_FLAG bit will be asserted. If Sleep Timer DMA Trigger Sleep Timer Registers This section describes the SFRs associated with the Sleep Timer. WORTIME0 (0xA5) - Sleep Timer Low Byte Bit Field Name Reset R/W Description 7:0 WORTIME[7:0] 0x00 R 8 LSB of the16 bits selected from the 31-bit Sleep Timer according to the setting of WORCTRL.WOR_RES[1:0] SWRS033G Page 127 of 244 CC1110Fx / CC1111Fx WORTIME1 (0xA6) - Sleep Timer High Byte Bit Field Name Reset R/W Description 7:0 WORTIME[15:8] 0x00 R 8 MSB of the16 bits selected from the 31-bit Sleep Timer according to the setting of WORCTRL.WOR_RES[1:0] WOREVT1 (0xA4) - Sleep Timer Event0 Timeout High Bit Field Name Reset R/W Description 7:0 EVENT0[15:8] 0x87 R/W High byte of Event 0 timeout register Sleep Timer clocked by low power RCOSC t Event 0 750 EVENT 0 25WOR _ RES f ref Sleep Timer clocked by 32.768 kHz crystal oscillator t Event0 1 EVENT 0 2 5WOR _ RES 32768 WOREVT0 (0xA3) - Sleep Timer Event0 Timeout Low Bit Field Name Reset R/W Description 7:0 EVENT0[7:0] 0x6B R/W Low byte of Event 0 timeout register WORCTRL (0xA2) - Sleep Timer Control Bit Field Name Reset R/W Description 7 - R0 Not used 6:4 111 R/W Reserved. Always write 000 3 - R0 Not used 2 WOR_RESET 0 R0/W1 Reset timer. The timer will be reset to 4. 1:0 WOR_RES[1:0] 00 R/W Sleep Timer resolution Controls the resolution and maximum timeout for the Sleep Timer. Adjusting the resolution does not affect the clock cycle counter: Setting Resolution (1 LSB) Bits selected from the 31-bit Sleep Timer 00 1 period 15:0 5 01 2 periods 20:5 10 210 periods 25:10 15 11 2 periods 30:15 WORIRQ (0xA1) - Sleep Timer Interrupt Control Bit Reset R/W 7:6 00 R0 5 0 R/W Reserved. Always write 0 0 R/W Event 0 interrupt mask 4 Field Name EVENT0_MASK Description 0 Interrupt is disabled 1 Interrupt is enabled 3:2 00 R0 1 0 R/W0 Reserved 0 R/W0 Event 0 interrupt flag 0 EVENT0_FLAG 0 No interrupt is pending 1 Interrupt is pending SWRS033G Page 128 of 244 CC1110Fx / CC1111Fx 12.9 8-bit Timers, Timer 3 and Timer 4 Timer 3 and Timer 4 are two 8-bit timers which supports typical timer/counter functions such as output compare and PWM functions. The timers have two independent compare channels each and use one I/O pin per channel. highest is 24 MHz for CC1111Fx. When the high speed RC oscillator is used as system clock source, the highest clock frequency used by Timer 3/4 is fXOSC/2 for CC1110Fx and 12 MHz for CC1111Fx, given that the HS RCOSC has been calibrated. The features of Timer 3/4 are as follows: The counter operates as either a free-running counter, a modulo counter, a down counter, or as an up/down counter for use in centrealigned PWM. Two compare channels Set, clear, or toggle output compare Free-running, modulo, down, up/down counter operation or It is possible to read the 8-bit counter value through the SFR TxCNT. Clock prescaler for divide by 1, 2, 4, 8, 16, 32, 64, 128 Writing a 1 to TxCTL.CLR will reset the 8-bit counter. Interrupt request generation on compare and when reaching the terminal count value The counter may produce an interrupt request when the terminal count value (overflow) is reached (see Section 12.9.3 - 12.9.3.3). It is possible to start and halt the counter with the TxCTL.START bit. The counter is started when a 1 is written to TxCTL.START. If a 0 is written to TxCTL.START, the counter halts at its present value. DMA trigger function Note: In the following sections, an n in the register name represent the channel number 0 or 1 if nothing else is stated. An x in the register name refers to the timer number, 3 or 4 12.9.1 12.9.2 8-bit Timer Counter Both timers consist of an 8-bit counter that increments or decrements at each active clock edge. The frequency of the active clock edges is given by CLKCON.TICKSPD and TxCTL.DIV. CLKCON.TICKSPD is used to set the timer tick speed. The timer tick speed will vary from 203.125 kHz to 26 MHz for CC1110Fx and 187.5 kHz to 24 MHz for CC1111Fx (given the use of a 26 MHz or 48 MHz crystal respectively). Note that the clock speed of the system clock is not affected by the TICKSPD setting. The timer tick speed is further divided in Timer 3/4 by the prescaler value set by TxCTL.DIV. This prescaler value can be 1, 2, 4, 8, 16, 32, 64, or 128. Thus the lowest clock frequency used by Timer 3/4 is 1.587 kHz and the highest is 26 MHz when a 26 MHz crystal oscillator is used as system clock source (CC1110Fx). The lowest clock frequency used by Timer 3/4 is 1.465 kHz and the Timer 3/4 Operation In general, the control register TxCTL is used to control the timer operation. The timer modes are described in the following four sections. 12.9.3 Free-running Mode In free-running mode the counter starts from 0x00 and increments at each active clock edge. When the counter reaches the terminal count value 0xFF (overflow), the counter is loaded with 0x00 on the next timer tick and continues incrementing its value as shown in Figure 35. When 0xFF is reached, the TIMIF.TxOVFIF flag is set. The IRCON.TxIF flag is only asserted if the corresponding interrupt mask bit TxCTL.OVFIM is set. An interrupt request is generated when both TxCTL.OVFIM and IEN1.TxEN are set to 1. The free-running mode can be used to generate independent time intervals and output signal frequencies. SWRS033G Page 129 of 244 CC1110Fx / CC1111Fx Figure 35: Free-running Mode 12.9.3.1 Modulo Mode TIMIF.TxOVFIF flag is set. The IRCON.TxIF flag is only asserted if the corresponding interrupt mask bit TxCTL.OVFIM is set. An interrupt request is generated when both TxCTL.OVFIM and IEN1.TxEN are set to 1. Modulo mode can be used for applications where a period other than 0xFF is required. In modulo mode the counter starts from 0x00 and increments at each active clock edge. When the counter reaches the terminal count value TxCC0 (overflow), the counter is loaded with 0x00 on the next timer tick and continues incrementing its value as shown in Figure 36. When TxCC0 is reached, the TxCC0 0x00 OVFIF = 1 OVFIF = 1 Figure 36: Modulo Mode 12.9.3.2 Down Mode IRCON.TxIF is only asserted if the corresponding interrupt mask bit TxCTL.OVFIM is set. An interrupt request is generated when both TxCTL.OVFIM and IEN1.TxEN are set to 1. The timer down mode can generally be used in applications where an event timeout interval is required. In down mode, after the timer has been started, the counter is loaded with the contents in TxCC0. The counter then counts down to 0x00 (terminal count value) and remains at 0x00 as shown in Figure 37. The flag TIMIF.TxOVFIF is set when 0x00 is reached. TxCC0 0x00 OVFIF = 1 Figure 37: Down Mode 12.9.3.3 Up/Down Mode In up/down mode the counter starts from 0x00 and increments at each active clock edge. When the counter value matches the terminal count value TxCC0, the counter counts down until 0x00 is reached and it starts counting up again as shown in Figure 38. When 0x00 is reached, the TIMIF.TxOVFIF flag is set. The IRCON.TxIF flag is only asserted if the corresponding interrupt mask bit TxCTL.OVFIM is set. An interrupt request is generated when both TxCTL.OVFIM and IEN1.TxEN are set to 1. The up/down mode can be used when symmetrical output pulses are required with a period other than 0xFF, and therefore allows implementation of centrealigned PWM output applications. SWRS033G Page 130 of 244 CC1110Fx / CC1111Fx Figure 38: Up/Down Mode 12.9.4 Channel Mode Control The channel mode is set with each channel's control and status register TxCCTLn. Note: before an I/O pin can be used by the timer, the required I/O pin must be configured as a Timer 3/4 peripheral pin as described in section 12.4.6 on Page 64. 12.9.5 may generate an interrupt Counter reaches terminal count value (overflow) or turns around on zero / reach zero Output compare event Output Compare Mode In output compare mode the I/O pin associated with a channel is set as an output. After the timer has been started, the contents of the counter are compared with the contents of the channel compare register TxCCn. If the compare register equals the counter contents, the output pin is set, reset, or toggled according to the compare output mode setting of TxCCTLn.CMP. Note that all edges on output pins are glitch-free when operating in a given compare output mode. Writing to the compare register TxCC0 does not take effect on the output compare value until the counter value is 0x00. Writing to the compare register TxCC1 takes effect immediately. When a compare occurs, the interrupt flag for the appropriate channel (TIMIF.TxCHnIF) is asserted. The IRCON.TxIF flag is only asserted if the corresponding interrupt mask bit TxCCTLn.IM is set to 1. An interrupt request is generated if the corresponding interrupt mask bit is set together with IEN1.TxEN. When operating in up-down mode, the interrupt flag for channel 0 is set when the counter reaches 0x00 instead of when a compare occurs. For simple PWM use, output compare modes 3 and 4 are preferred. 12.9.6 timer events request: The register bits TIMIF.T3OVFIF, TIMIF.T4OVFIF, TIMIF.T3CH0IF, TIMIF.T3CH1IF, TIMIF.T4CH0IF, and TIMIF.T4CH1IF contains the interrupt flags for the two terminal count value event (overflow), and the four channel compare events, respectively. These flags will be asserted regardless off the channel n interrupt mask bit (TxCCTLn.IM). The CPU interrupt flag, IRCON.TxIF will only be asserted if one or more of the channel n interrupt mask bits are set to 1. An interrupt request is only generated when the corresponding interrupt mask bit is set together with IEN1.TxEN. The interrupt mask bits are T3CCTL0.IM, T3CCTL1.IM, T4CCTL0.IM, T4CCTL1.IM, T3CTL.OVFIM, and T4CTL.OVFIM. Note that enabling an interrupt mask bit will generate a new interrupt request if the corresponding interrupt flag is set. When the timer is used in Free-running Mode or Modulo Mode the interrupt flags are set as follows: TIMIF.TxCH0IF and TIMIF.TxCH1IF are set on compare event TIMIF.TxOVFIF is set when counter reaches terminal count value (overflow) When the timer is used in Down Mode the interrupt flags are set as follows: Timer 3 and 4 Interrupts There is one interrupt vector assigned to each of the timers. These are T3 and T4 (interrupt #11 and #12, see Table 39). The following SWRS033G TIMIF.TxCH0IF and TIMIF.TxCH1IF are set on compare event TIMIF.TxOVFIF is set when counter reaches zero Page 131 of 244 CC1110Fx / CC1111Fx When the timer is used in Up/Down Mode the interrupt flags are set as follows: TIMIF.TxCH0IF and TIMIF.TxOVFIF are set when the counter turns around on zero TIMIF.TxCH1IF is set on compare event 12.9.8 Timer 3 and 4 Registers This section describes the following Timer 3 and Timer 4 registers: In addition, the CPU interrupt flag, IRCON.TxIF will be asserted if the channel n interrupt mask bit (TxCCTLn.IM) is set to 1. T3CNT - Timer 3 Counter T3CTL - Timer 3 Control T3CCTLn - Timer 3 Channel n Compare Control T3CCn - Timer 3 Channel n Compare Value T4CNT - Timer 4 Counter 12.9.7 Timer 3 and Timer 4 DMA Triggers There are two DMA triggers associated with Timer 3 and two DMA triggers associated with Timer 4. These are DMA triggers T3_CH0, T3_CH1, T4_CH0, and T4_CH1, which are generated on timer compare events as follows: T3_CH0: Timer 3 channel 0 compare T4CTL - Timer 4 Control T4CCTLn - Timer 4 Channel n Compare Control T4CCn - Timer 4 Channel n Compare Value TIMIF - Timer 1/3/4 Interrupt Mask/Flag T3_CH1: Timer 3 channel 1 compare T4_CH0: Timer 4 channel 0 compare T4_CH1: Timer 4 channel 1 compare T3CNT (0xCA) - Timer 3 Counter Bit Field Name Reset R/W Description 7:0 CNT[7:0] 0x00 R Timer count byte. Contains the current value of the 8-bit counter SWRS033G Page 132 of 244 CC1110Fx / CC1111Fx T3CTL (0xCB) - Timer 3 Control Bit Field Name Reset R/W Description 7:5 DIV[2:0] 000 R/W Prescaler divider value. Generates the active clock edge used to update the counter as follows: 000 Tick frequency /1 001 Tick frequency /2 010 Tick frequency /4 011 Tick frequency /8 100 Tick frequency /16 101 Tick frequency /32 110 Tick frequency /64 111 Tick frequency /128 Note: Changes to these bits has immediate effect on the frequency of the active clock edges. 4 3 2 START OVFIM CLR 0 1 0 R/W R/W0 R0/W1 Start timer 0 Suspended 1 Normal operation Overflow interrupt mask 0 Interrupt disabled 1 Interrupt enabled Clear counter. Writing a 1 resets the counter to 0x00. This bit will be 0 when returning from PM2 and PM3 1:0 MODE[1:0] 00 R/W Timer 3 mode select. The timer operating mode is selected as follows: 00 Free running, repeatedly count from 0x00 to 0xFF 01 Down, count from T3CC0 to 0x00 10 Modulo, repeatedly count from 0x00 to T3CC0 11 Up/down, repeatedly count from 0x00 to T3CC0 and from T3CC0 down to 0x00 SWRS033G Page 133 of 244 CC1110Fx / CC1111Fx T3CCTL0 (0xCC) - Timer 3 Channel 0 Compare Control Bit Field Name 7 6 5:3 2 IM CMP[2:0] MODE 1:0 Reset R/W Description - R0 Not used 1 R/W Channel 0 interrupt mask 000 0 00 R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Channel 0 compare output mode select. Specified action on output when timer value equals compare value in T3CC0 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set output on compare, clear on 0xFF 110 Clear output on compare, set on 0x00 111 Not used Timer 3 channel 0 compare mode enable 0 Disable 1 Enable Reserved. Always write 00 T3CC0(0xCD) - Timer 3 Channel 0 Compare Value Bit Field Name Reset R/W Description 7:0 VAL[7:0] 0x00 R/W Timer 3 channel 0 compare value SWRS033G Page 134 of 244 CC1110Fx / CC1111Fx T3CCTL1 (0xCE) - Timer 3 Channel 1 Compare Control Bit Field Name 7 6 5:3 2 IM CMP[2:0] MODE 1:0 Reset R/W Description - R0 Not used 1 R/W Channel 1 interrupt mask 000 0 00 R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Channel 1 compare output mode select. Specified action on output when timer value equals compare value in T3CC1 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set output on compare, clear on T3CC0 110 Clear output on compare, set on T3CC0 111 Not used Timer 3 channel 1 compare mode enable 0 Disable 1 Enable Reserved. Always write 00 T3CC1 (0xCF) - Timer 3 Channel 1 Compare Value Bit Field Name Reset R/W Description 7:0 VAL[7:0] 0x00 R/W Timer 3 channel 1 compare value T4CNT (0xEA) - Timer 4 Counter Bit Field Name Reset R/W Description 7:0 CNT[7:0] 0x00 R Timer count byte. Contains the current value of the 8-bit counter SWRS033G Page 135 of 244 CC1110Fx / CC1111Fx T4CTL (0xEB) - Timer 4 Control Bit Field Name Reset R/W Description 7:5 DIV[2:0] 000 R/W Prescaler divider value. Generates the active clock edge used to update the counter as follows: 000 Tick frequency /1 001 Tick frequency /2 010 Tick frequency /4 011 Tick frequency /8 100 Tick frequency /16 101 Tick frequency /32 110 Tick frequency /64 111 Tick frequency /128 Note: Changes to these bits has immediate effect on the frequency of the active clock edges. 4 3 2 START OVFIM CLR 0 1 0 R/W R/W0 R0/W1 Start timer 0 Suspended 1 Normal operation Overflow interrupt mask 0 Interrupt disabled 1 Interrupt enabled Clear counter. Writing a 1 resets the counter to 0x00. This bit will be 0 when returning from PM2 and PM3 1:0 MODE[1:0] 00 R/W Timer 4 mode select. The timer operating mode is selected as follows: 00 Free running, repeatedly count from 0x00 to 0xFF 01 Down, count from T4CC0 to 0x00 10 Modulo, repeatedly count from 0x00 to T4CC0 11 Up/down, repeatedly count from 0x00 to T4CC0 and from T4CC0 down to 0x00 SWRS033G Page 136 of 244 CC1110Fx / CC1111Fx T4CCTL0 (0xEC) - Timer 4 Channel 0 Compare Control Bit Field Name 7 6 5:3 2 IM CMP[2:0] MODE 1:0 Reset R/W Description - R0 Not used 1 R/W Channel 0 interrupt mask 000 0 00 R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Channel 0 compare output mode select. Specified action on output when timer value equals compare value in T4CC0 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set output on compare, clear on 0xFF 110 Clear output on compare, set on 0x00 111 Not used Timer 4 channel 0 compare mode enable 0 Disable 1 Enable Reserved. Always write 00 T4CC0 (0xED) - Timer 4 Channel 0 Compare Value Bit Field Name Reset R/W Description 7:0 VAL[7:0] 0x00 R/W Timer 4 channel 0 compare value SWRS033G Page 137 of 244 CC1110Fx / CC1111Fx T4CCTL1 (0xEE) - Timer 4 Channel 1 Compare Control Bit Field Name 7 6 5:3 2 IM CMP[2:0] MODE 1:0 Reset R/W Description - R0 Not used 1 R/W Channel 0 interrupt mask 000 0 00 R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Channel 0 compare output mode select. Specified action on output when timer value equals compare value in T4CC0 000 Set output on compare 001 Clear output on compare 010 Toggle output on compare 011 Set output on compare-up, clear on 0 (clear on compare-down in up/down mode) 100 Clear output on compare-up, set on 0 (set on compare-down in up/down mode) 101 Set output on compare, clear on T4CC0 110 Clear output on compare, set on T4CC0 111 Not used Timer 4 channel 1 compare mode enable 0 Disable 1 Enable Reserved. Always write 00 T4CC1 (0xEF) - Timer 4 Channel 1 Compare Value Bit Field Name Reset R/W Description 7:0 VAL[7:0] 0x00 R/W Timer 4 channel 1 compare value SWRS033G Page 138 of 244 CC1110Fx / CC1111Fx TIMIF (0xD8) - Timers 1/3/4 Interrupt Mask/Flag Bit Field Name 7 6 5 4 3 2 1 0 OVFIM T4CH1IF T4CH0IF T4OVFIF T3CH1IF T3CH0IF T3OVFIF Reset R/W Description - R0 Not used 1 R/W Timer 1 overflow interrupt mask 0 0 0 0 0 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 0 Interrupt disabled 1 Interrupt enabled Timer 4 channel 1 interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending Timer 4 channel 0 interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending Timer 4 overflow interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending Timer 3 channel 1 interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending Timer 3 channel 0 interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending Timer 3 overflow interrupt flag. Writing a 1 has no effect 0 No interrupt is pending 1 Interrupt is pending SWRS033G Page 139 of 244 CC1110Fx / CC1111Fx 12.10 ADC Eight individual input channels, singleended or differential (CC1111Fx has only six channels) 12.10.1 ADC Introduction The ADC supports up to 12-bit analog-todigital conversion. The ADC includes an analog multiplexer with up to eight individually configurable channels, reference voltage generator, and conversion results written to memory through DMA. Several modes of operation are available. All references to VDD applies to voltage on the pin AVDD. Reference voltage selectable as internal, external single ended, external differential, or VDD. Interrupt request generation DMA triggers at end of conversions The main features of the ADC are as follows: Temperature sensor input Selectable decimation rates which also sets the resolution (7 to 12 bits). Battery measurement capability Figure 39: ADC Block Diagram 12.10.2 ADC Operation This section describes the general setup and operation of the ADC and describes the usage of the ADC control and status registers accessed by the CPU. 12.10.2.1 ADC Core The ADC is capable of converting an analog input into a digital representation with up to 12 bits resolution. The ADC uses a selectable positive reference voltage. 12.10.2.2 ADC Inputs The signals on the P0 port pins can be used as ADC inputs. Note: P0_6 and P0_7 do not exist on CC1111Fx, hence only six input channels are available (AIN0 - AIN5) To configure a P0 pin to be used as an ADC input the corresponding bit in the ADCCFG register must be set to 1. The default value in this register disables the ADC inputs. Please see Section 12.4.6.7 on Page 94 for more details on how to configure the ADC input pins. In the following these port pin will be referred to as the AIN0 - AIN7 pins. The ADC can be set up to automatically perform a sequence of conversions and optionally perform an extra conversion. It is possible to configure the inputs as singleended or differential inputs. In the case where differential inputs are selected, the differential inputs consist of the input pairs AIN0 - AIN1, AIN2 - AIN3, AIN4 - AIN5, and AIN6 - AIN7. Note that neither a negative supply, nor a supply larger than VDD (unregulated power) can be applied to these pins. It is the difference between the pairs that are converted in differential mode. In addition to the input pins AIN0 - AIN7, the output of an on-chip temperature sensor can be selected as an input to the ADC for temperature measurements. SWRS033G Page 140 of 244 CC1110Fx / CC1111Fx It is also possible to select a voltage corresponding to VDD/3 as an ADC input. This input allows the implementation of e.g. a battery monitor in applications where this feature is required. 12.10.2.3 ADC Conversion Sequences The ADC will perform a sequence of conversions, and the results can be moved to memory (through DMA) without any interaction from the CPU. The ADCCON2.SCH register bits are used to define an ADC conversion sequence from the ADC inputs. If some of the inputs in this sequence are not configured to be analog input signals in the ADCCFG register, these will be skipped. For differential inputs both input pins must be configured to be analog input signals. 0000 ADCCON2.SCH 0111: Singleended inputs 1000 ADCCON2.SCH Differential inputs 1011: 1100 ADCCON2.SCH 1111: GND, internal voltage reference, temp. sensor, and VDD/3 When ADCCON2.SCH is set to a value less than 1000 a conversion sequence will contain a conversion from each ADC input, starting at AIN0 and ending at the input programmed in ADCCON2.SCH. When ADCCON2.SCH is set to a value ranging from 1000 to 1011, the sequence will start at the differential input pair (AIN0 - AIN1) and stop at the input pair given by ADCCON2.SCH. For even higher settings, only single conversions are performed. In addition to this sequence of conversions, the ADC can be programmed to perform a single conversion (see next section). ADCCON1.STSEL=11, and no conversion is currently running. When the sequence is completed, this bit is automatically cleared. The ADCCON1.STSEL bits select which event that will start a new sequence of conversions. The options which can be selected are rising edge on external pin P2_0, end of previous sequence, a Timer 1 channel 0 compare event, or ADCCON1.ST is 1. ADCCON2.SREF is used to select the reference voltage. The reference voltage should only be changed when no conversion is running. The ADCCON2.SDIV bits select the decimation rate (and thereby also the resolution and time required to complete a conversion and sample rate). The decimation rate should only be changed when no conversion is running. The ADCCON2.SCH register bits are used to define an ADC conversion sequence. The ADC can be programmed to perform a single conversion (single-ended, differential, GND, internal voltage reference, temperature sensor, or VDD/3). This is called an extra conversion and is controlled with the ADCCON3 register. This conversion is triggered by writing to ADCCON3. If this register is written while the ADC is running, the conversion will take place as soon as the sequence has completed. If the register is written while the ADC is not running, the conversion will take place immediately after the ADCCON3 register is updated. The ADCCON3 register controls which input to use, reference voltage, and decimation rate for the extra conversion. The coding of the register bits is exactly as for ADCCON2. Note: If a sequence of conversions is started without setting any of the P0 pins as analog inputs, ADCCON2.SCH and ADCCON1.EOC will still be updated, as if the conversions had taken place. 12.10.2.4 ADC Operating Modes This section describes the operating modes and initialization of conversions. The ADC has three control registers: ADCCON1, ADCCON2, and ADCCON3. These registers are used to configure the ADC and to report status. The ADCCON1.EOC bit is a status bit that is set high when a conversion ends and cleared when ADCH is read. The ADCCON1.ST bit is used to start a sequence of conversions. A sequence will start when this bit is set high, 12.10.2.5 ADC Reference Voltage The positive reference voltage for analog-todigital conversions is selectable as either an internally generated 1.25 V voltage, VDD on the AVDD pin, an external voltage applied to the AIN7 input pin, or a differential voltage applied to the AIN6 - AIN7 inputs (AIN6 must have the highest input voltage). It is possible to select the reference voltage as the input to the ADC in order to perform a conversion of the reference voltage e.g. for calibration purposes. Similarly, it is possible to select the ground terminal GND as an input. SWRS033G Page 141 of 244 CC1110Fx / CC1111Fx presented within this data sheet assume the use of the high speed crystal oscillator. Note: P0_6 and P0_7 do not exist on CC1111Fx, hence it is not possible to use external voltage reference for the ADC on the CC1111Fx. 12.10.2.6 ADC Conversion Results The digital conversion result is represented in two's complement form. For single ended configurations the result is always positive (the result is the difference between ground and the input signal AINn, where n is 0, 1, 2, ..., 7) and will be a value between 0 and 2047. The maximum value is reached when the input amplitude is equal VREF, the selected voltage reference. For differential configurations the difference between two pin pairs are converted and this difference can be negatively signed. For 12-bit resolution the digital conversion result is 2047 when the analog input is equal to VREF, and the conversion result is -2048 when the analog input is equal to -VREF. The time required to perform a conversion depends on the selected decimation rate. When, for instance, the decimation rate is set to 128, the decimation filter uses exactly 128 ADC clock periods to calculate the result. When a conversion is started, the input multiplexer is allowed 16 ADC clock periods to settle in case the channel has been changed since the previous conversion. The 16 clock cycles settling time applies to all decimation rates. This means that the conversion time, Tconv, is given by: Tconv = (decimation rate + 16) x T where 0.22 s T 0.23 s for CC1110Fx, depending on the frequency of the high speed crystal oscillator T = 0.25 s for CC1111Fx The digital conversion result is available in ADCH and ADCL when ADCCON1.EOC is set to 1. Note that the conversion result always resides in MSB section of ADCH:ADCL. 12.10.2.8 ADC Interrupts When reading the ADCCON2.SCH bits, the number returned will indicate what the last conversion was. Notice that when the value written to ADCCON2.SCH is less than 1100, the number returned will be the number written + 1. For example, after a sequence of conversions from AIN0 to AIN4 has completed, ADCCON2.SCH will be read as 0101, while after a single conversion of the temperature sensor has completed, the register field will be read as 1110 (same as the value written to it). If an extra conversion has been initiated by writing to ADCCON3.ECH, ADCCON2.SCH will be updated, after the conversion has completed, with the same value as written to ADCCON3.ECH, even if this value was less than 1100. 12.10.2.9 ADC DMA Triggers 12.10.2.7 ADC Conversion Timing The DMA triggers are listed in Table 51 on age 107. The high speed crystal oscillator should be selected as system clock when the ADC is used and CLKCON.CLKSPD should be 000. The ADC runs on a clock which is the system clock divided by 6 to give a 4.33/4 MHz ADC clock. Both the delta-sigma modulator and the decimation filter use the ADC clock for their calculations. Using other frequencies will affect the results, and conversion time. All data The ADC will only generate an interrupt when an extra conversion has completed. DMA triggers 20 - 28 are associated with single-ended or differential conversion sequences (ADCCON2.SCH 1100). The ADC will generate a DMA trigger event when a new sample is ready from a conversion in the sequence. The same is the case if a single conversion is completed (ADCCON2.SCH 1100). Be aware that DMA trigger number 27 2 and 28 are shared with the I S module. In addition there is one DMA trigger, ADC_CHALL, which is active when new data is ready from any of the conversions in the ADC conversion sequence and from the single conversion defined by ADCCON2.SCH. A completion of an extra conversion will not generate a trigger event. 12.10.3 ADC Registers This section describes the ADC registers. SWRS033G Page 142 of 244 CC1110Fx / CC1111Fx ADCL (0xBA) - ADC Data Low Bit Field Name Reset R/W Description 7:4 ADC[3:0] 0000 R Least significant part of ADC conversion result. The decimation rate configures through ADCCON2.SDIV determines how many of these bits are relevant to use. 0000 R 3:0 ADCH (0xBB) - ADC Data High Bit Field Name Reset R/W Description 7:0 ADC[11:4] 0x00 R Most significant part of ADC conversion result. The decimation rate configures through ADCCON2.SDIV determines how many of these bits are relevant to use. ADCCON1 (0xB4) - ADC Control 1 Bit Field Name Reset R/W Description 7 EOC 0 R H0 End of conversion. Cleared when ADCH has been read. If a new conversion is completed before the previous data has been read, the EOC bit will remain high. 6 5:4 3:2 1:0 ST STSEL[1:0] RCTRL[1:0] 0 11 00 11 R/W1 R/W R/W R/W 0 Conversion not complete 1 Conversion completed Start conversion. Read as 1 until conversion has completed 0 No conversion in progress 1 Start a conversion sequence if ADCCON1.STSEL=11 and no sequence is running. Start select. Selects which event that will start a new conversion sequence. 00 External trigger on P2_0 pin. 01 Full speed. Do not wait for triggers. 10 Timer 1 channel 0 compare event 11 ADCCON1.ST=1 Controls the 16 bit random generator. When set to 01, the setting will automatically return to 00 when operation has completed. 00 Operation completed 01 Clock the LFSR once (13x unrolling) 10 Reserved 11 Reserved Reserved. Always write 11 SWRS033G Page 143 of 244 CC1110Fx / CC1111Fx ADCCON2 (0xB5) - ADC Control 2 Bit Field Name Reset R/W Description 7:6 SREF[1:0] 00 R/W Selects reference voltage used for the sequence of conversions 5:4 3:0 SDIV[1:0] SCH[3:0] 01 00 R/W R/W 00 Internal 1.25V reference 01 External reference on AIN7 pin (only CC1110Fx) 10 VDD on the AVDD pin 11 External reference on AIN6 - AIN7 differential input (only CC1110Fx) Sets the decimation rate for channels included in the sequence of conversions. The decimation rate also determines the resolution and time required to complete a conversion. 00 64 dec rate (7 bits resolution) 01 128 dec rate (9 bits resolution) 10 256 dec rate (10 bits resolution) 11 512 dec rate (12 bits resolution) Sequence Channel Select. Selects the end of the sequence. SCH 0111: A conversion sequence will contain a conversion from each ADC input, starting at AIN0 and ending at the input programmed in ADCCON2.SCH. 1000 SCH 1011: The sequence will start at the differential input pair (AIN0 AIN1) and stop at the input pair given by ADCCON2.SCH. SCH 1100: Only single conversions are performed. When reading the ADCCON2.SCH bits, the number returned will indicate what the last conversion was. Please see Section 12.10.2.6 for details. 0000 AIN0 0001 AIN1 0010 AIN2 0011 AIN3 0100 AIN4 0101 AIN5 0110 AIN6 0111 AIN7 1000 AIN0 - AIN1 1001 AIN2 - AIN3 1010 AIN4 - AIN5 1011 AIN6 - AIN7 1100 GND 1101 Positive voltage reference 1110 Temperature sensor 1111 VDD/3 SWRS033G Page 144 of 244 CC1110Fx / CC1111Fx ADCCON3 (0xB6) - ADC Control 3 Bit Field Name Reset R/W Description 7:6 EREF[1:0] 00 R/W Selects reference voltage used for the extra conversion 5:4 3:0 EDIV[1:0] ECH[3:0] 00 0000 R/W R/W 00 Internal 1.25V reference 01 External reference on AIN7 pin (only CC1110Fx) 10 VDD on the AVDD pin 11 External reference on AIN6 - AIN7 differential input (only CC1110Fx) Sets the decimation rate used for the extra conversion. The decimation rate also determines the resolution and time required to complete the conversion. 00 64 dec rate (7 bits resolution) 01 128 dec rate (9 bits resolution) 10 256 dec rate (10 bits resolution) 11 512 dec rate (12 bits resolution) Extra channel select. An extra conversion will be triggered by writing to these bits. If they are written while the ADC is running, the conversion will take place as soon as the sequence has completed. If the bits are written while the ADC is not running, the conversion will take place immediately after this register has been updated. The bits are automatically cleared when the extra conversion has finished. 0000 AIN0 0001 AIN1 0010 AIN2 0011 AIN3 0100 AIN4 0101 AIN5 0110 AIN6 0111 AIN7 1000 AIN0 - AIN1 1001 AIN2 - AIN3 1010 AIN4 - AIN5 1011 AIN6 - AIN7 1100 GND 1101 Positive voltage reference 1110 Temperature sensor 1111 VDD/3 SWRS033G Page 145 of 244 CC1110Fx / CC1111Fx 12.11 Random Number Generator 12.11.1 Introduction The random number following features. generator has The random number generator is a 16-bit Linear Feedback Shift Register (LFSR) with the Generate pseudo-random bytes which can be read by the CPU. polynomial X X X 1 (i.e. CRC16). It uses different levels of unrolling depending on the operation it performs. The basic version (no unrolling) is shown below. Calculate CRC16 of bytes that are written to RNDH. The random number generator is turned off when ADCCON1.RCTRL=11. 16 15 2 Seeded by value written to RNDL. 15 in_bit + 14 13 12 11 10 9 8 7 6 5 4 3 2 + 1 0 + Figure 40: Basic Structure of the Random Number Generator 12.11.2 Random Operation Number Generator The operation of the random number generator is controlled by the ADCCON1.RCTRL bits. The current value of the 16-bit shift register in the LFSR can be read from the RNDH and RNDL registers. 12.11.2.1 Semi Random Sequence Generation To generate pseudo-random bytes, ADCCON1.RCTRL should be set to 01. This will clock the LFSR once (13x unrolling) and the ADCCON1.RCTRL bits will automatically be cleared when the operation has completed. 12.11.2.3 CRC16 The LFSR can also be used to calculate the CRC value of a sequence of bytes. Writing to the RNDH register will trigger a CRC calculation. The new byte is processed from the MSB end and an 8x unrolling is used, so that a new byte can be written to RNDH every clock cycle. Note that the LFSR must be properly seeded by writing to RNDL twice, before the CRC calculations start. Usually the seed value should be 0x0000 or 0xFFFF. Using 0xFFFF as seed value will give the CRC used by the radio. For the following byte sequence: 0x03, 0x41, 0x42, 0x43 12.11.2.2 Seeding The LFSR can be seeded by writing to the RNDL register twice. Each time the RNDL register is written, the 8 LSB of the LFSR is copied to the 8 MSB and the 8 LSBs are replaced with the new data byte that was written to RNDL. The CRC will be 0xB4BC when using 0xFFFF as seed value. 12.11.3 Registers The random number generator registers are described in this section. SWRS033G Page 146 of 244 CC1110Fx / CC1111Fx RNDL (0xBC) - Random Number Generator Data Low Byte Bit Field Name Reset R/W Description [7:0] RNDL[7:0] 0xFF R/W Random value/seed or CRC result, low byte When used for random number generation writing this register twice will seed the random number generator. Writing to this register copies the 8 LSBs of the LFSR to the 8 MSBs and replaces the 8 LSBs with the data value written. The value returned when reading from this register is the 8 LSBs of the LFSR. When used for random number generation, reading this register returns the 8 LSBs of the random number. When used for CRC calculations, reading this register returns the 8 LSBs of the CRC result. RNDH (0xBD) - Random Number Generator Data High Byte Bit Field Name Reset R/W Description [7:0] RNDH[7:0] 0xFF R/W Random value or CRC result/input data, high byte When written, a CRC16 calculation will be triggered, and the data value written is processed starting with the MSB bit. The value returned when reading from this register is the 8 MSBs of the LFSR. When used for random number generation, reading this register returns the 8 MSBs of the random number. When used for CRC calculations, reading this register returns the 8 MSBs of the CRC result. 12.12 AES Coprocessor The CC1110Fx/CC1111Fx data encryption is performed using a dedicated coprocessor which supports the Advanced Encryption Standard, AES. The coprocessor allows encryption/decryption to be performed with minimal CPU usage. The coprocessor has the following features: ECB, CBC, CFB, OFB, CTR, and CBC- MAC modes. Hardware support for CCM mode 128-bits key and IV/Nonce 12.12.2 Key and IV Before a key or IV/nonce load starts, an appropriate load key or IV/nonce command must be issued to the coprocessor. When loading the IV it is important to also set the correct mode. A key load or IV load operation aborts any processing that could be running. The key, once loaded, stays valid until a key reload takes place. The IV must be downloaded before the beginning of each message (not block). DMA transfer trigger capability Both key and IV are cleared by a reset of the device and when PM2 or PM3 are entered. 12.12.1 AES Operation To encrypt a message, procedure must be followed: the following AES works on blocks of 128 bits. If a block contains less than 128 bits, it must be padded with zeros when written to the coprocessor. Load key Load initialization vector (IV)/nonce Download and upload encryption/decryption. data 12.12.3 Padding of Input Data for The AES coprocessor works on blocks of 128 bits. A block of data is loaded into the coprocessor, encryption is performed, and the result must be read out before the next block can be processed. Before each block load, a dedicated start command must be sent to the coprocessor. 12.12.4 Interface to CPU The CPU communicates coprocessor using three SFRs: with the ENCCS, Encryption control and status register ENCDI, Encryption input register ENCDO, Encryption output register SWRS033G Page 147 of 244 CC1110Fx / CC1111Fx Read/write to the control and status register is done by the CPU, while read/write the output/input registers is intended for use together with direct memory access (DMA). When using DMA, one channel is used for input data and one for output data. The DMA channels must be initialized before a start command is written to the ENCCS. Writing a start command generates a DMA trigger and the transfer is started. After each block is processed, the interrupt flag, S0CON.ENCIF, is asserted, and an interrupt request generated if IEN0.ENCIE is set to 1. The interrupt is used to issue a new start command to the ENCCS. Before the last block is loaded, the mode must be changed to CBC. The last block is then downloaded and the block uploaded will be the MAC value. CBC-MAC decryption is similar to encryption. The message MAC uploaded must be compared with the MAC to be verified. 12.12.6 AES Interrupts The AES interrupt flag, S0CON.ENCIF, is asserted when encryption or decryption of a block is completed. An interrupt request is generated if IEN0.ENCIE is set to 1 12.12.7 AES DMA Triggers 12.12.5 Modes of Operation ECB and CBC modes are performed as described in Section 12.12.1 When using CFB, OFB, and CTR mode, the 128 bits blocks are divided into four 32 bit blocks. 32 bits are loaded into the AES coprocessor and the resulting 32 bits are read out. This continues until all 128 bits have been encrypted. The only time one has to consider this is if data is loaded/read directly using the CPU. When using DMA, this is handled automatically by the DMA triggers generated by the AES coprocessor, thus DMA is preferred. Both encryption and performed similarly. decryption are The CBC-MAC mode is a variant of the CBC mode. When performing CBC-MAC, data is downloaded to the coprocessor one 128 bits block at a time, except for the last block. There are two DMA triggers associated with the AES coprocessor. These are ENC_DW, which is active when input data needs to be downloaded to the ENCDI register, and ENC_UP, which is active when output data needs to be uploaded from the ENCDO register. The ENCDI and ENCDO registers should be set as destination and source locations for DMA channels used to transfer data to or from the AES coprocessor. 12.12.8 AES Registers The AES coprocessor registers are described below. These registers will be in their reset state when returning to active mode from PM2 and PM3. SWRS033G Page 148 of 244 CC1110Fx / CC1111Fx ENCCS (0xB3) - Encryption Control and Status Bit Field Name 7 6:4 3 2:1 0 MODE[2:0] RDY CMD[1:0] ST Reset R/W Description 0 R0 Not used 000 R/W Encryption/decryption mode 1 0 0 R R/W R/W1 H0 000 CBC 001 CFB 010 OFB 011 CTR 100 ECB 101 CBC MAC 110 Reserved 111 Reserved Encryption/decryption ready status 0 Encryption/decryption in progress 1 Encryption/decryption is completed Command to be performed when a 1 is written to ST. 00 encrypt block 01 decrypt block 10 load key 11 load IV/nonce Start processing command set by CMD. Must be issued for each command or 128 bits block of data. Cleared by hardware ENCDI (0xB1) - Encryption Input Data Bit Field Name Reset R/W Description 7:0 DIN[7:0] 0x00 R/W Encryption input data. ENCDO (0xB2) - Encryption Output Data Bit Field Name Reset R/W Description 7:0 DOUT[7:0] 0x00 R/W Encryption output data. SWRS033G Page 149 of 244 CC1110Fx / CC1111Fx 12.13 Watchdog Timer The watchdog timer (WDT) is intended as a recovery method in situations where the software hangs. The WDT shall reset the system when software fails to clear the WDT within a selected time interval. The watchdog can be used in applications where high reliability is required. If the watchdog function is not needed in an application, it is possible to configure the watchdog timer to be used as an interval timer that can be used to generate interrupts at selected time intervals. The features of the watchdog timer are as follows: Four selectable timer intervals Watchdog mode Timer mode Interrupt request generation in timer mode Clock independent from system clock The operation of the WDT module is controlled by the WDCTL register. The watchdog timer consists of a 15-bit counter clocked by the one of the low speed oscillators. Note that the content of the 15-bit counter is not user-accessible. The content of the 15-bit counter is reset to 0x0000 when a PM2 or PM3 is entered. 12.13.1 Watchdog Mode The watchdog timer is disabled after a system reset. To set the WDT in watchdog mode the WDCTL.MODE bit must be set to 0. The watchdog timer counter starts incrementing when the enable bit WDCTL.EN is set to 1. When the timer is enabled in watchdog mode it is not possible to disable the timer. Therefore, writing a 0 to WDCTL.EN has no effect if a 1 was already written to this bit when WDCTL.MODE was 0. The WDT operates with a watchdog timer clock frequency of 32.768 kHz (low speed crystal oscillator) or 32 - 36 kHz (calibrated low power RC oscillator). The timer interval depend on the count value settings (64, 512, 8192, and 32768 respectively) configured in WDCTL.INT. If the counter reaches the selected timer interval value (watchdog timeout), the watchdog timer generates a reset signal for the system. If a watchdog clear sequence is performed before the counter reaches the selected timer interval value, the counter is reset to 0x0000 and continues incrementing its value. The watchdog clear sequence consists of writing 1010 to WDCTL.CLR[3:0] followed by writing 0101 to the same register bits within one half of a watchdog clock period. If this complete sequence is not performed, the watchdog timer generates a reset signal for the system. Note that as long as a correct watchdog clear sequence begins within the selected timer interval, the counter is reset when the complete sequence has been received. When the watchdog timer has been enabled in watchdog mode, it is not possible to change the mode by writing to the WDCTL.MODE bit. The timer interval value can be changed by writing to the WDCTL.INT[1:0] bits. Note that a change in the timer interval value should be followed by a clearing of the watchdog timer to avoid an unwanted watchdog reset. In watchdog mode, the WDT does not produce an interrupt request. 12.13.2 Timer Mode To set the WDT in normal timer mode, the WDCTL.MODE bit is set to 1. When register bit WDCTL.EN is set to 1, the timer is started and the counter starts incrementing. When the counter reaches the selected interval value, the IRCON2.WDTIF flag is asserted and an interrupt request is generated if watchdog timer interrupt is enabled (IEN2.WDTIE=1). In timer mode, it is possible to clear the timer contents by writing a 1 to WDCTL.CLR[0]. When the timer is cleared the contents of the counter is set to 0x0000. The timer is stopped by setting WDCTL.EN=0 and restarted from 0x000 by setting WDCTL.EN=1. The timer interval is set by the WDCTL.INT[1:0] bits. In timer mode, a reset will not be produced when the timer interval value is reached. 12.13.3 Watchdog Mode and Power Modes In active mode and PM0 the WDT runs and resets the chip upon timeout. To avoid reset, SWRS033G Page 150 of 244 CC1110Fx / CC1111Fx the watchdog timer must be cleared before the counter expires. Power Mode Comments PM1 The WDT runs but does not reset the chip upon timeout. If active mode is entered just as the timer expires, the chip will be reset immediately, hence the WDT needs to be cleared regularly (before timeout) also when in PM1. PM2 and PM3 The WDT is disabled and reset, and the configuration is retained. The counter will start from 0x0000 when active mode is entered from PM2 or PM3 Table 54: Watchdog Mode and Power Modes 12.13.4 Watchdog Timer Register WDCTL (0xC9) - Watchdog Timer Control Bit Field Name Reset R/W Description 7:4 CLR[3:0] 0000 R/W Clear timer. When 1010 followed by 0101 is written to these bits, the counter is reset to 0x0000. Note that the watchdog will only be cleared when 0101 is written within 0.5 watchdog clock period after 1010 was written. Writing to these bits when EN is 0 has no effect. 3 EN 0 R/W Enable timer. When a 1 is written to this bit the timer is enabled and starts incrementing. Writing a 0 to this bit in timer mode stops the timer. Writing a 0 to this bit in watchdog mode has no effect. 2 1:0 MODE INT[1:0] 0 00 R/W R/W 0 Timer disabled 1 Timer enabled Mode select. 0 Watchdog mode 1 Timer mode Timer interval select. These bits select the timer interval defined as a given number of low speed oscillator periods. Timer interval # of periods 32.768 kHz crystal oscillator 32 kHz RCOSC 34.667 kHz RCOSC (calibrated, CC1111Fx) (calibrated, CC1110Fx running @ 26 MHz) 00 32768 1s 1.024 s 0.945 s 01 8192 0.25 s 0.256 s 0.236 s 10 512 15.625 ms 16 ms 14.769 ms 11 64 1.953 ms 2 ms 1.846 ms SWRS033G Page 151 of 244 CC1110Fx / CC1111Fx 12.14 USART USART0 and USART1 are serial communications interfaces that can be operated separately in either asynchronous UART mode or in synchronous SPI mode. The two USARTs are identical in functionality but are assigned to separate I/O pins. Refer to Section 12.4 on Page 90 for I/O configuration. 12.14.1 UART Mode For asynchronous serial interfaces, the UART mode is provided. In UART mode the interface uses a two-wire or four-wire interface consisting of the pins RXD and TXD, and optionally RTS and CTS. The UART mode includes the following features: 8 or 9 data bits Odd, even, or no parity Configurable start and stop bit level Configurable LSB or MSB first transfer Independent interrupts receive and transmit Independent receive and transmit DMA triggers Parity and framing error status The UART mode provides full duplex asynchronous transfers and the synchronization of bits in the receiver does not interfere with the transmit function. A UART byte transfer consists of a start bit, eight data bits, an optional ninth data or parity bit, and one or two stop bits. Note that the data transferred is referred to as a byte, although the data can actually consist of eight or nine bits. The UART operation is controlled by the USART x Control and Status registers, UxCSR, and the USART x UART Control register, UxUCR, where x is the USART number, 0 or 1. The UART mode is UxCSR.MODE is set to 1. selected when 12.14.1.1 UART Transmit A UART transmission is initiated when the USART Receive/Transmit Data Buffer, UxDBUF register is written. The byte is transmitted on the TXDx output pin. The UxDBUF register is double-buffered. The UxCSR.ACTIVE bit goes high when the byte transmission starts and low when it ends. When the transmission ends, the UxCSR.TX_BYTE bit is set to 1. The USARTx TX complete CPU interrupt flag (IRCON2.UTXxIF) is asserted when the UxDBUF register is ready to accept new transmit data, and an interrupt request is generated if IEN2.UTXxIE=1. This happens immediately after the transmission has been started, hence a new data byte value can be loaded into the data buffer while the byte is being transmitted. 12.14.1.2 UART Receive Data reception on the UART is initiated when a 1 is written to the UxCSR.RE bit. The UART will then search for a valid start bit on the RXDx input pin and set the UxCSR.ACTIVE bit high. When a valid start bit has been detected the received byte is shifted into the receive register. The UxCSR.RX_BYTE bit and the CPU interrupt flag, TCON.URXxIF, is set to 1 when the operation has completed and an interrupt request is generated if IEN0.URXxIE=1. At the same time UxCSR.ACTIVE will go low. The received data byte is available through the UxDBUF register. When UxDBUF is read, UxCSR.RX_BYTE is cleared by hardware. 12.14.1.3 UART Hardware Flow Control Hardware flow control is enabled when the UxUCR.FLOW bit is set to 1. The RTS output will then be driven low when the receive register is empty and reception is enabled. Transmission of a byte will not occur before the CTS input go low. 12.14.1.4 UART Character Format If the BIT9 and PARITY bits in register UxUCR are set high, parity generation and detection is enabled. The parity is computed and transmitted as the ninth bit, and during reception, the parity is computed and compared to the received ninth bit. If there is a parity error, the UxCSR.ERR bit is set high. This bit is cleared when UxCSR is read. The number of stop bits to be transmitted is set to one or two bits determined by the register bit UxUCR.SPB. The receiver will always check for one stop bit. If the first stop bit received during reception is not at the expected stop bit level, a framing error is signaled by setting register bit UxCSR.FE high. UxCSR.FE is cleared when SWRS033G Page 152 of 244 CC1110Fx / CC1111Fx UxCSR is read. The receiver will check both stop bits when UxUCR.SPB=1. Note that the USARTx RX complete CPU interrupt flag, TCON.URXxIF, and the UxCSR.RX_BYTE bit will be asserted when the first stop bit is checked OK. If the second stop bit is not OK, the framing error bit, UxCSR.FE, will be asserted. This means that this bit is updated 1 bit duration later than the 2 other above mentioned bits. The UxCSR.ACTIVE bit will be de-asserted after the second stop bit (if UxUCR.SPB=1). 12.14.2 SPI Mode This section describes the SPI mode of operation for synchronous communication. In SPI mode, the USART communicates with an external system through a 3-wire or 4-wire interface. The interface consists of the pins MOSI, MISO, SCK and SSN. Refer to Section 12.4 on Page 90 for I/O configuration. The SPI mode includes the following features: 3-wire (master) and 4-wire SPI interface Master and slave modes Configurable SCK polarity and phase asserted and the received data byte is available in UxDBUF. An interrupt request is generated if IEN0.URXxIE=1 Since UxDBUF is double-buffered, the assertion of the USARTx TX complete CPU interrupt flag (IRCON2.UTXxIF) happens just after a transmission has been initiated, and is therefore not safe to use. Instead, the assertion of the UxCSR.TX_BYTE bit should be used as an indication on when new data can be written to UxDBUF. For DMA transfers this is handled automatically, but with the limitation that the UxGCR.CPHA bit must be set to zero. For systems requiring setting UxGCR.CPHA=1, the DMA can not be used. Also note that the USARTx TX complete interrupt occurs approximately 1 byte period prior to the USARTx RX complete interrupt. In SPI master mode, only the MOSI, MISO, and SCK should be configured as peripherals (see Section 12.4.6.1 and 12.4.6.2). If the external slave requires a slave select signal (SSN) this can be implemented by using a general-purpose I/O pin and control from SW. 12.14.2.2 SPI Slave Operation Configurable LSB or MSB first transfer The SPI mode is selected when UxCSR.MODE is set to 0. In SPI mode, the USART can be configured to operate either as an SPI master or as an SPI slave by setting UxCSR.SLAVE to 0 or 1, respectively. 12.14.2.1 SPI Master Operation An SPI byte transfer in master mode is initiated when the UxDBUF register is written. The USART generates the SCK signal using the baud rate generator (see Section 12.14.3) and shifts the provided byte from the transmit register onto the MOSI output. At the same time the receive register shifts in the received byte from the MISO input pin. The polarity and clock phase of the serial clock SCK is selected by UxGCR.CPOL and UxGCR.CPHA. The order of the byte transfer is selected by the UxGCR.ORDER bit. The UxCSR.ACTIVE bit goes high when the transfer starts and low when the transfer ends. When the transfer ends, the UxCSR.TX_BYTE bit is set to 1. An SPI byte transfer in slave mode is controlled by the external system. The data on the MOSI input is shifted into the receive register controlled by the serial clock SCK, which is an input in slave mode. At the same time the byte in the transmit register is shifted out onto the MISO output. The UxCSR.ACTIVE bit is set to 1 when SNN is asserted and cleared when SNN is deasserted. The UxCSR.RX_BYTE bit is set to 1 when a byte transfer ends. At the end of the transfer, the USARTx RX complete CPU interrupt flag, TCON.URXxIF, is asserted and the received data byte is available in UxDBUF. An interrupt request is generated if IEN0.URXxIE=1. The USARTx TX complete CPU interrupt flag, IRCON2.UTXxIF, is asserted at the start of the operation and an interrupt request is generated if IEN2.UTXxIE=1. The expected polarity and clock phase of SCK is selected by UxGCR.CPOL and UxGCR.CPHA as shown in Figure 41. The expected order of the byte transfer is selected by the UxGCR.ORDER bit. At the end of the transfer, the USARTx RX complete CPU interrupt flag, TCON.URXxIF, is SWRS033G Page 153 of 244 CC1110Fx / CC1111Fx 12.14.2.3 Slave Select pin (SSN) When the USART is operating in SPI slave mode, a 4-wire interface is used with the Slave Select (SSN) pin as an input to the SPI (edge controlled). The SPI slave becomes active after a falling edge on SSN and will receive data on the MOSI input and send data on the MISO output. After a rising edge on SSN, the SPI slave is inactive and will not receive data. Note that the MISO output is not tri-stated when the SPI slave is inactive. Also note that the rising edge on SSN must be aligned to the end of the byte sent / received. If this is not the case, the next received byte will be corrupted. If there is a rising edge on SSN in the middle of a byte, this should be followed by a USART flush to avoid corruption of the following byte. In SPI master mode, the SSN pin is not used. When the USART operates as an SPI master and a slave select signal is needed by an external SPI slave device, a general purpose I/O pin should be used to implement the slave select signal function in software. Figure 41: SPI Dataflow 12.14.3 Baud Rate Generation An internal baud rate generator set up the UART baud rate when operating in UART mode and the SPI master clock frequency when operating in SPI mode. The UxBAUD.BAUD_M[7:0] and UxGCR.BAUD_E[4:0] registers define the baud rate used for UART transfers and the rate of the serial clock (SCK) for SPI transfers. The baud rate is given by the following equation: Baudrate (256 BAUD _ M ) 2 2 28 BAUD _ E F where F is the system clock frequency set by the selected system clock source. The register values required for standard baud rates are shown in Table 55 (F = 26 MHz) and Table 56 (24 MHz). The tables also give the difference in actual baud rate to standard baud rate value as a percentage error. The maximum baud rate for UART mode is F/16 (UxGCR.BAUD_E[4:0]=16 and UxBAUD.BAUD_M[7:0]=0). The maximum baud rate for SPI master mode and thus SCK frequency is F/8 (UxGCR.BAUD_E[4:0]=17 and UxBAUD.BAUD_M[7:0]=0). If SPI master mode does not need to receive data, the SWRS033G Page 154 of 244 CC1110Fx / CC1111Fx maximum SPI rate is F/2 (UxGCR.BAUD_E[4:0]=19 and UxBAUD.BAUD_M[7:0]=0). Setting higher baud rates than this will give erroneous results. For SPI slave mode the maximum baud rate is always F/8. Note that the baud rate must be configured before any other UART or SPI operations take place (the baud rate should never be changed when UxCSR.ACTIVE is asserted). Baud Rate [bps] UxBAUD.BAUD_M UxGCR.BAUD_E Error (%) 2400 131 6 0.04 4800 131 7 0.04 9600 131 8 0.04 14400 34 9 0.13 19200 131 9 0.04 28800 34 10 0.13 38400 131 10 0.04 57600 34 11 0.13 76800 131 11 0.04 115200 34 12 0.13 230400 34 13 0.13 Table 55: Commonly used Baud Rate Settings for 26 MHz System Clock Baud Rate [bps] UxBAUD.BAUD_M UxGCR.BAUD_E Error (%) 2400 163 6 0.08 4800 163 7 0.08 9600 163 8 0.09 14400 59 9 0.13 19200 163 9 0.10 28800 59 10 0.14 38400 163 10 0.10 57600 59 11 0.14 76800 163 11 0.10 115200 59 12 0.14 230400 59 13 0.14 Table 56: Commonly used Baud Rate Settings for 24 MHz System Clock 12.14.4 USART Flushing 12.14.5 USART Interrupts The current operation can be aborted (operation stopped and all data buffers cleared) by setting UxUCR.FLUSH=1.Asserting the FLUSH bit should either be aligned with USART interrupts or a wait time of one bit duration (at current baud rate) should be added after setting the bit to 1 before accessing the USART registers. Each USART has two interrupts. These are the USART x RX complete interrupt (TCON.URXxIF) and the USART x TX complete interrupt (IRCON2.UTXxIF). The interrupts are enabled by setting IEN0.URXxIE=1 and IEN2.UTXxIE=1, respectively. Please see the previous sections on how the interrupt flags are asserted in the different modes of operation (UART RX, UART TX, SPI master, and SPI Slave). SWRS033G Page 155 of 244 CC1110Fx / CC1111Fx The interrupt enables summarized below. and flags are Interrupt enable bits: configured using a USART Receive/transmit buffer, UxDBUF, as source or destination address. USART0 RX : IEN0.URX0IE Note: For systems requiring setting UxGCR.CPHA=1, the DMA can not be used. USART1 RX : IEN0.URX1IE USART0 TX : IEN2.UTX0IE Refer to Table 51 on Page 107 for an overview of the DMA triggers. USART1 TX : IEN2.UTX1IE Interrupt flags: USART0 RX : TCON.URX0IF 12.14.7 USART Registers USART1 RX : TCON.URX1IF The registers for the USART are described in this section. For each USART there are five registers consisting of the following (x refers to USART number i.e. 0 or 1): USART0 TX : IRCON2.UTX0IF USART1 TX : IRCON2.UTX1IF UxCSR USART x Control and Status 12.14.6 USART DMA Triggers UxUCR USART x UART Control There are two DMA triggers associated with each USART (URX0, UTX0, URX1, and UTX1). The DMA triggers are activated by RX complete and TX complete events i.e. the same events that might generate USART interrupt requests. A DMA channel can be UxGCR USART x Generic Control SWRS033G UxDBUF USART x Receive/Transmit Data Buffer UxBAUD USART x Baud Rate Control Page 156 of 244 CC1110Fx / CC1111Fx U0CSR (0x86) - USART 0 Control and Status Bit Field Name Reset R/W Description 7 MODE 0 R/W USART 0 mode select 0 SPI mode 1 UART mode 6 RE 0 R/W UART 0 receiver enable 0 Receiver disabled 1 Receiver enabled 5 SLAVE 0 R/W SPI 0 master or slave mode select 0 SPI master 1 SPI slave 4 FE 0 R/W 0 UART 0 framing error status 0 No framing error detected 1 Byte received with incorrect stop bit level Note: TCON.URX0IF and U0CSR.RX_BYTE bit will be asserted when the first stop bit is checked OK, meaning that if two stop bits are sent and the second stop bit is not OK, this bit is asserted 1 bit duration later than the 2 other above mentioned bits. 3 ERR 0 R/W 0 UART 0 parity error status 0 No parity error detected 1 Byte received with parity error 2 RX_BYTE 0 R/W 0 Receive byte status 0 No byte received 1 Received byte ready 1 TX_BYTE 0 R/W 0 Transmit byte status 0 Byte not transmitted 1 Last byte written to Data Buffer register transmitted 0 ACTIVE 0 R USART 0 transmit/receive active status 0 USART 0 idle 1 USART 0 busy in transmit or receive mode SWRS033G Page 157 of 244 CC1110Fx / CC1111Fx U0UCR (0xC4) - USART 0 UART Control Bit Field Name Reset R/W Description 7 FLUSH 0 R0/ W1 Flush unit. When set to 1, this event will immediately stop the current operation and return the unit to idle state. This bit will be 0 when returning from PM2 and PM3 6 5 FLOW D9 0 0 R/W R/W UART 0 hardware flow control enable. Selects use of hardware flow control with RTS and CTS pins 0 Flow control disabled 1 Flow control enabled UART 0 data bit 9 contents. This value is used when 9 bit transfer is enabled. When parity is disabled the value written to D9 is transmitted as the 9th bit when BIT9=1. If parity is enabled then this bit sets the parity level as follows. 4 3 2 1 0 BIT9 PARITY SPB STOP START 0 0 0 1 0 R/W R/W R/W R/W R/W 0 Even parity 1 Odd parity UART 0 9-bit data enable 0 8 bits transfer 1 9 bits transfer (content of the 9th bit is given by D9 and PARITY.) UART 0 parity enable 0 Parity disabled 1 Parity enabled UART 0 number of stop bits 0 1 stop bit 1 2 stop bits UART 0 stop bit level 0 Low stop bit 1 High stop bit UART 0 start bit level. The polarity of the idle line is assumed to be the opposite of the selected start bit level. 0 Low start bit 1 High start bit U0GCR (0xC5) - USART 0 Generic Control Bit Field Name Reset R/W Description 7 CPOL 0 R/W SPI 0 clock polarity 6 5 4:0 CPHA ORDER BAUD_E[4:0] 0 0 00000 R/W R/W R/W 0 Negative clock polarity (SCK low when idle) 1 Positive clock polarity (SCK high when idle) SPI 0 clock phase 0 Data centered on first edge of SCK period 1 Data centered on second edge of SCK period Bit order for transfers 0 LSB first 1 MSB first Baud rate exponent value. BAUD_E along with BAUD_M decides the UART 0 baud rate and the SPI 0 clock (SCK) frequency SWRS033G Page 158 of 244 CC1110Fx / CC1111Fx U0DBUF (0xC1) - USART 0 Receive/Transmit Data Buffer Bit Field Name Reset R/W Description 7:0 DATA[7:0] 0x00 R/W USART 0 receive and transmit data buffer. Writing data to U0DBUF places the data into the internal transmit buffer. Reading U0DBUF returns the contents of the receive buffer. U0BAUD (0xC2) - USART 0 Baud Rate Control Bit Field Name Reset R/W Description 7:0 BAUD_M[7:0] 0x00 R/W Baud rate mantissa value. BAUD_M along with BAUD_E decides the UART 0 baud rate and the SPI 0 clock (SCK) frequency U1CSR (0xF8) - USART 1 Control and Status Bit Field Name Reset R/W Description 7 MODE 0 R/W USART 1 mode select 0 SPI mode 1 UART mode 6 RE 0 R/W UART 1 receiver enable 0 Receiver disabled 1 Receiver enabled 5 SLAVE 0 R/W SPI 1 master or slave mode select 0 SPI master 1 SPI slave 4 FE 0 R/W 0 UART 1 framing error status 0 No framing error detected 1 Byte received with incorrect stop bit level Note that TCON.URX1IF and U1CSR.RX_BYTE bit will be asserted when the first stop bit is checked OK, meaning that if two stop bits are sent and the second stop bit is not OK, this bit is asserted 1 bit duration later than the 2 other above mentioned bits. 3 ERR 0 R/W 0 UART 1 parity error status 0 No parity error detected 1 Byte received with parity error 2 RX_BYTE 0 R/W 0 Receive byte status 0 No byte received 1 Received byte ready 1 TX_BYTE 0 R/W 0 Transmit byte status 0 Byte not transmitted 1 Last byte written to Data Buffer register transmitted 0 ACTIVE 0 R USART 1 transmit/receive active status 0 USART 1 idle 1 USART 1 busy in transmit or receive mode SWRS033G Page 159 of 244 CC1110Fx / CC1111Fx U1UCR (0xFB) - USART 1 UART Control Bit Field Name Reset R/W Description 7 FLUSH 0 R0/ W1 Flush unit. When set to 1, this event will immediately stop the current operation and return the unit to idle state. This bit will be 0 when returning from PM2 and PM3 6 5 FLOW D9 0 0 R/W R/W UART 1 hardware flow control enable. Selects use of hardware flow control with RTS and CTS pins 0 Flow control disabled 1 Flow control enabled UART 1 data bit 9 contents. This value is used when 9 bit transfer is enabled. When parity is disabled the value written to D9 is transmitted as the 9th bit when BIT9=1 If parity is enabled then this bit sets the parity level as follows. 4 3 2 1 0 BIT9 PARITY SPB STOP START 0 0 0 1 0 R/W R/W R/W R/W R/W 0 Even parity 1 Odd parity UART 1 9-bit data enable 0 8 bits transfer 1 9 bits transfer (content of the 9th bit is given by D9 and PARITY.) UART 1 parity enable 0 Parity disabled 1 Parity enabled UART 1 number of stop bits 0 1 stop bit 1 2 stop bits UART 1 stop bit level 0 Low stop bit 1 High stop bit UART 1 start bit level. The polarity of the idle line is assumed to be the opposite of the selected start bit level. 0 Low start bit 1 High start bit U1GCR (0xFC) - USART 1 Generic Control Bit Field Name Reset R/W Description 7 CPOL 0 R/W SPI 1 clock polarity 6 5 4:0 CPHA ORDER BAUD_E[4:0] 0 0 00000 R/W R/W R/W 0 Negative clock polarity (SCK low when idle) 1 Positive clock polarity (SCK high when idle) SPI 1 clock phase 0 Data centered on first edge of SCK period 1 Data centered on second edge of SCK period Bit order for transfers 0 LSB first 1 MSB first Baud rate exponent value. BAUD_E along with BAUD_M decides the UART 1 baud rate and the SPI 1 clock (SCK) frequency SWRS033G Page 160 of 244 CC1110Fx / CC1111Fx U1DBUF (0xF9) - USART 1 Receive/Transmit Data Buffer Bit Field Name Reset R/W Description 7:0 DATA[7:0] 0x00 R/W USART 1 receive and transmit data buffer. Writing data to U1DBUF places the data into the internal transmit buffer. Reading U1DBUF returns the contents of the receive buffer. U1BAUD (0xFA) - USART 1 Baud Rate Control Bit Field Name Reset R/W Description 7:0 BAUD_M[7:0] 0x00 R/W Baud rate mantissa value. BAUD_M along with BAUD_E decides the UART 1 baud rate and the SPI 1 clock (SCK) frequency 2 12.15 I S The CC1110Fx/CC1111Fx provides an industry 2 2 standard I S interface. The I S interface can be used to transfer digital audio samples between the CC1110Fx/CC1111Fx and an external audio device. 2 The I S interface can be configured to operate as master or slave and may use mono as well as stereo samples. When mono mode is enabled, the same audio sample will be used for both channels. Both full and half duplex is supported and automatic -Law compression and expansion can be used. 2 The I S interface consists of 4 signals: Continuous Serial Clock (SCK) Word Select (WS) Please see Section 12.4.6.6 for details on I/O 2 pin mapping for the I S interface. When the module is in master mode, it drives the SCK 2 and WS lines. When the I S interface is in slave mode, these lines are driven by an external master. The data on the serial data lines is transferred one bit per SCK cycle, most significant bit first. The WS signal selects the channel of the current word transfer (left = 0, right = 1). It also determines the length of each word. There is a transition on the WS line one bit time before the first word is transferred and before the last bit of each word. Figure 42 2 shows the I S signaling. Only a single serial data signal is shown in this figure. The SD signal could be the RX or TX signal depending on the direction of the data. Serial Data In (RX) Serial Data Out (TX) 2 Figure 42: I S Digital Audio Signaling 2 2 12.15.1 Enabling I S 12.15.2 I S Interrupts The I2SCFG0.ENAB bit must be set to 1 to 2 enable the I S transmitter/receiver. However, 2 when I2SCFG0.ENAB is 0, the I S can still be used as a stand-alone -Law compression/expansion engine. Refer to Section 12.15.12 on Page 164 for more details about this. The I S has two interrupts: 2 I S RX complete interrupt (I2SRX) 2 I S TX complete interrupt (I2STX) 2 2 The I S interrupt enable bits are found in the I2SCFG0 register. The interrupt flags are SWRS033G Page 161 of 244 CC1110Fx / CC1111Fx located in the I2SSTAT register. The interrupt enables and flags are summarized below. Interrupt enable bits: I S RX: I2SCFG0.RXIEN 2 I S TX: I2SCFG0.TXIEN 2 Interrupt flags: I S RX: I2SSTAT.RXIRQ 2 Notice that the DMA triggers I2SRX and ADC_CH6 share the same DMA trigger number (# 27) in the same way as I2STX and ADC_CH7 share DMA trigger number 28. This means that I2SRX can not be used together with ADC_CH6 and I2STX can not be used together with ADC_CH7. On the CC1111Fx ADC channels 6 and 7 cannot be used since P0_6 and P0_7 I/O pins are not available. Refer to Table 51 on Page 107 for an overview of the DMA triggers. I S TX: I2SSTAT.TXIRQ 2 The TX interrupt flag I2SSTAT.TXIRQ is asserted together with IRCON2.I2STXIF when the internal TX buffer is empty and the 2 I S fetches the new data previously written to the I2SDATH:I2SDATL registers. The TX interrupt flag, I2SSTAT.TXIRQ, is cleared when I2SDATH register is written. An interrupt request is only generated when I2SCFG0.TXIEN and IEN2.I2STXIE are both set to 1. The RX interrupt flag I2SSTAT.RXIRQ is asserted together with TCON.I2SRXIF when the internal RX buffer is full and the contents of the RX buffer is copied to the pair of internal data registers that can be read from the I2SDATH:I2SDATL registers. The RX interrupt flag, I2SSTAT.RXIRQ, is cleared when the I2SDATH register is read. An interrupt request is only generated when I2SCFG0.RXIEN and IEN0.I2SRXIE are both set to 1. Notice that interrupts will also be generated if the corresponding RXIRQ or TXIRQ flags are set from software, given that the interrupts are enabled. 2 The I S shares interrupt vector with USART 1, and the ISR must take this into account if both modules are used. Refer to 10.5 on Page 60 for more details about interrupts. 12.15.4 Underflow/Overflow 2 If the I S attempts to read from the internal TX buffer when it is empty, an underflow condition 2 occurs. The I S will then continue to read from the data in the TX buffer, and I2SSTAT.TXUNF will be asserted. 2 If the I S attempts to write to the internal RX buffer while it is full, an overflow condition occurs. The contents of the RX buffer will be overwritten and the I2SSTAT.RXOVF flag will be asserted. Thus, when debugging an application, software may check for underflow/overflow when an interrupt is generated or when the application completes. The TXUNF / RXOVF flags should be cleared in software. 12.15.5 Writing a Word (TX) When each sample fits into a single byte or Law compressed samples (always 8 bits) are written, i.e. -Law expansion is enabled (I2SCFG0.ULAWE=1), only the I2SDATH register needs to be written. When each sample is more than 8 bits the low byte must be written to the I2SDATL register before the high byte is written to the I2SDATH register, hence writing the I2SDATH register indicates the completion of the write operation. 2 2 12.15.3 I S DMA Triggers There are two DMA triggers associated with 2 the I S interface, I2SRX and I2STX. The DMA triggers are activated by RX complete and TX complete events, i.e. the same events that can 2 generated the I S interrupt requests. The DMA triggers are not masked by the interrupt enable bits, I2SCFG0.RXIEN and I2SCFG0.TXIEN, hence a DMA channel can be configured to 2 use the I S receive/transmit data registers, I2SDATH:I2SDATL, as source or destination address and let RX and TX complete trigger the DMA. When the I S is configured to send stereo, i.e. I2SCFG0.TXMONO is 0, the I2SSTAT.TXLR flag can be used to determine whether the leftor right-channel sample is to be written to the data registers. 12.15.6 Reading a Word (RX) If each sample fits into a single byte or if -Law compression is enabled (I2SCFG0.ULAWC=1), only the I2SDATH register needs to be read. When each sample is more than 8 bits the low byte must be read from the I2SDATL register before the high byte is being read from the SWRS033G Page 162 of 244 CC1110Fx / CC1111Fx I2SDATH register, hence reading from the I2SDATH register indicates the completion of the read operation. division is given by the 15 bit numerator, NUM , and 9-bit denominator, DENOM, as shown in the following formula: 2 When the I S is configured to receive stereo, i.e. I2SCFG0.RXMONO is 0, the I2SSTAT.RXLR flag can be used to determine whether the sample currently in the data registers is a left- or right-channel sample. 12.15.7 Full vs. Half Duplex 2 The I S interface supports full duplex and half duplex operation. In full duplex both the RX and TX lines will be used. Both the I2SCFG0.TXIEN and I2SCFG0.RXIEN interrupt enable bits must be set to 1 if interrupts are used and both DMA triggers I2STX and I2SRX must be used. When half duplex is used only one of the RX and TX lines are typically connected. Only the appropriate interrupt flag should be set and only one of the DMA triggers should be used. 12.15.8 Master Mode 2 The I S is configured as a master device by setting I2SCFG0.MASTER to 1. When the module is in master mode, it drives the SCK and WS lines. 12.15.8.1 Clock Generation 2 When the I S is configured as master, the frequency of the SCK clock signal must be set to match the sample rate. The clock frequency must be set before master mode is enabled. Fsck where Fclk NUM 2( ) DENOM NUM 3.35 DENOM Fclk is the system clock frequency and Fsck is the 2 I S SCK sample clock frequency. The value of the numerator is set in the I2SCLKF2.NUM[14:8]:I2SCLKF1.NUM[7:0] registers and the denominator value is set in I2SCLKF2.DENOM[8]:I2SCLKF0.DENOM[7:0]. Please note that to stay within the timing 2 requirements of the I S specification [7], a minimum value of 3.35 should be used for the (NUM / DENOM) fraction. The fractional divider is made such that most normal sample rates should be supported for most normal word sizes with a 24 MHz system clock frequency (CC1111Fx). Examples of supported configurations for a 24 MHz system clock are given in Table 57. Table 58 shows the configuration values for a 26 MHz system clock 2 frequency. Notice that the generated I S frequency is not exact for the 44.1 kHz, 16 bits word size configuration at 26 MHz. The numbers are calculated using the following formulas, where Fs is the sample rate and W is the word size: Fs CLKDIV SCK is generated by dividing the system clock using a fractional clock divider. The amount of Fsck 2 W NUM Fclk DENOM 4 W Fs Fs (kHz) Word Size (W) CLKDIV I2SCLKF2 I2SCLKF1 I2SCLKF0 Exact 8 8 93.75 0x01 0x77 0x04 Yes 8 16 46.875 0x01 0x77 0x08 Yes 44.1 16 8.503401 0x04 0xE2 0x93 Yes 48 16 7.8125 0x00 0x7D 0x10 Yes Table 57: Example I S Clock Configurations (CC1111Fx, 24 MHz) 2 Fs (kHz) Word Size (W) CLKDIV I2SCLKF2 I2SCLKF1 I2SCLKF0 Exact 8 8 101.5625 0x06 0x59 0x10 Yes 8 16 50.78125 0x06 0x59 0x20 Yes 44.1 16 9.21201 0x8A 0x2F 0x1B No 48 16 8.46354 0x06 0x59 0xC0 Yes Table 58: Example I S Clock Configurations (CC1110Fx, 26 MHz) 2 SWRS033G Page 163 of 244 CC1110Fx / CC1111Fx 12.15.8.2 Word Size 12.15.11 Word Counter The word size must be set before master mode is enabled. The word size is the number of bits used for each sample and can be set to a value between 1 and 33. To set the word size, write word size - 1 to the I2SCFG1.WORDS[4:0] bits. Setting the word 2 size to a value of 17 or more causes the I S to pad each word with 0's in the least significant bits since the data registers provide maximum 16 bits. This feature allows samples to be sent 2 to an I S device that takes a higher resolution than 16 bits. The I S contains a 10-bit word counter, which is counting transitions on the WS line. The counter can be cleared by triggers or by writing to the I2SWCNT register. When a trigger occurs, or a value is written to I2SWCNT, the current value of the word counter is copied into the I2SSTAT.WCNT[9:8]:I2SWCNT.WCNT[7:0]regi sters and the word counter is cleared. 2 Three triggers can be used to copy/clear the word counter. USB SOF: USB Start of Frame. Occurs every ms (CC1111Fx only) If the size of the received samples exceeds 16 bits, only the 16 most significant bits will be put in the data registers and the remaining low order bits will be discarded. 12.15.9 Slave Mode 2 The I S is configured as a slave device by setting I2SCFG0.MASTER to 0. When in slave mode the SCK and WS signals are generated 2 by an external I S master and are inputs to the 2 I S interface. 12.15.9.1 Word Size 2 When the I S operates in slave mode, the word size is determined by the master that generates the WS signal. 2 The I S will provide bits from the internal 16-bit buffer until the buffer is empty. If the buffer becomes empty and the master still requests 2 more bits, the I S will send 0's (low order bits). If more than 16 bits are being received, the low order bits are discarded. 12.15.10 Mono 2 The I S also supports mono audio samples. To receive mono samples, I2SCFG0.RXMONO should be set to 1. Words from the right channel will then not be read into the data registers. This feature is included because some mono devices repeat their audio data in both channels and the left channel is the default mono channel. To send mono samples, I2SCFG0.TXMONO should be set to 1. Each word will then be repeated in both channels before a new word is fetched from the data registers. This is to enable sending a mono audio signal to a stereo audio sink device. T1_CH0: Timer 1, compare, channel 0 IOC_1: IO pin input transition (P1_3) Which trigger to use is configured through the TRIGNUM field in the I2SCFG1 register. When 2 the I S is configured not to use any trigger (I2SCFG1.TRIGNUM=0), the word counter can only be copied/cleared from software. The word counter will saturate if it reaches its maximum value. Software should configure the trigger-interval and sample-rate to ensure this never happens. CC1111Fx: The word counter is typically used to calculate the average sample rate over a long period of time (e.g. 1 second) needed by adaptive isochronous USB endpoints. The USB SOF event must then be used as trigger. 12.15.12 -Law Compression and Expansion 2 The I S interface can be configured to perform -Law compression and expansion. -Law compression is enabled by setting the I2SCFG0.ULAWC bit to 1 and -Law expansion is enabled by setting the I2SCFG0.ULAWE bit to 1. 2 When the I S interface is enabled, i.e. the I2SCFG0.ENAB bit is 1, and -Law expansion is enabled, every byte of -Law compressed data written to the I2SDATH register is expanded to a 16-bit sample before being 2 transmitted. When the I S interface is enabled and -Law compression is enabled each sample received is compressed to an 8-bit Law sample and put in the I2SDATH register. 2 When the I S interface is disabled, i.e. the I2SCFG0.ENAB bit is 0, it can still be used to perform -Law compression/expansion for other resources in the system. To perform an expansion, I2SCFG0.ULAWE must be 1 and SWRS033G Page 164 of 244 CC1110Fx / CC1111Fx I2SCFG0.ULAWC must be 0 before writing a byte of compressed data to the I2SDATH register. The expansion takes one clock cycle to perform, and then the result can be read from the I2SDATH:I2SDATL registers. To perform a compression I2SCFG0.ULAWE must be 0 and I2SCFG0.ULAWC must be 1. To start the compression, an un-compressed 16bit sample should be written to the I2SDATH:I2SDATL registers. The compression takes one clock cycle to perform, and then the result can be read from the I2SDATH register. Only one of the flags I2SCFG0.ULAWC and I2SCFG0.ULAWE should be set to 1 when the I2SCFG0.ENAB bit is 0. 2 12.15.13 I S Registers This section describes all the registers used for 2 2 I S control and status. The I S registers reside in XDATA memory space in the region 0xDF40 - 0xDF48. Table 33 on Page 52 gives an overview of register addresses while the tables in this section describe each register. Notice that the reset values for the registers reflect a configuration with 16-bit stereo samples and 2 44.1 kHz sample rate. The I S is not enabled at reset. SWRS033G Page 165 of 244 CC1110Fx / CC1111Fx 2 0xDF40: I2SCFG0 - I S Configuration Register 0 Bit Field Name Reset R/W Description 7 TXIEN 0 R/W Transmit interrupt enable 6 5 4 3 2 1 0 RXIEN ULAWE ULAWC TXMONO RXMONO MASTER ENAB 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Receive interrupt enable 0 Interrupt disabled 1 Interrupt enabled -Law expansion enable 0 Expansion disabled 1 Expansion enabled ENAB=0 Expand data written to I2SDATH ENAB=1 Enable expansion of data to transmit -Law compression enable 0 Compression disabled 1 Compression enabled ENAB=0 Compress data written to I2SDATH:I2SDATL ENAB=1 Enable compression of data received TX mono enable 0 Stereo mode 1 Each sample of audio data will be repeated in both channels before a new sample is fetched. This is to enable sending a mono signal to a stereo audio sink device. RX mono enable 0 Stereo mode 1 Data from the right channel will be discarded, i.e. not be read into the data registers. This feature is included because some mono devices repeat their audio data in both channels and left is the default mono channel. Master mode enable 0 Slave (CLK and WS are read from the pads) 1 Master (generate the CLK and WS) 2 I S interface enable 0 Disable (I2S can be used as a -Law compression/expansion unit) 1 Enable SWRS033G Page 166 of 244 CC1110Fx / CC1111Fx 2 0xDF41: I2SCFG1 - I S Configuration Register 1 Bit Field Name Reset R/W Description 7:3 WORDS[4:0] 01111 R/W This field gives the word size - 1. The word size is the bit-length of one sample for one channel. Used to generate the WS signal when in master mode. Reset value 01111 corresponds to 16 bit samples. 2:1 0 TRIGNUM[1:0] IOLOC 00 0 R/W R/W Word counter copy / clear trigger 00 No trigger. Counter copied / cleared by writing to the I2SWCNT register 01 USB SOF (CC1111Fx only) 10 IOC_1 (P1_3) 11 T1_CH0 The pin locations for the I2S signals. This bit selects between the two alternative pin mapping alternatives. Refer to Table 50 on Page 92 for an overview of pin locations. 0 Alt. 1 in Table 50 is used 1 Alt. 2 in Table 50 is used Note: If the I2S interface is enabled (I2SCFG0_ENAB=1), the I2S interface will have precedence in cases where other peripherals (except for the debug interface) are configured to be on the same location. This is the case even if the pins are configured to be general purpose I/O pins. 2 0xDF42: I2SDATL - I S Data Low Byte Bit Field Name Reset R/W Description 7:0 I2SDAT[7:0] 0x00 R/W Data register low byte. If this register is not written between two writes to the I2SDATH register, the low byte of the TX register will be cleared. Note: This register will be in its reset state when returning to active mode from PM2 and PM3. 2 0xDF43: I2SDATH - I S Data High Byte Bit Field Name Reset R/W Description 7:0 I2SDAT[15:8] 0x00 R/W Data register high byte. When this register is read, I2SSTAT.RXIRQ is de-asserted and the RX buffer is considered empty. When this register is written, I2SSTAT.TXIRQ is de-asserted and the TX buffer is considered full. Note: This register will be in its reset state when returning to active mode from PM2 and PM3. 2 0xDF44: I2SWCNT - I S Word Count Register Bit Field Name Reset R/W Description 7:0 WCNT[7:0] 0x00 R/W This register contains the 8 low order bits of the 10-bit internal word counter at the time of the last trigger. If this register is written (any value), the value of the internal word counter is copied into this register and I2SSTAT.WCNT[9:8], and the internal word counter is cleared. Refer to Section 12.15.11 for details about how to use this register. SWRS033G Page 167 of 244 CC1110Fx / CC1111Fx 2 0xDF45: I2SSTAT - I S Status Register Bit Field Name Reset R/W Description 7 TXUNF 0 R/W TX buffer underflow. This bit must be cleared by software 6 RXOVF 0 R/W Rx buffer overflow. This bit must be cleared by software 5 TXLR 0 R 0 Left channel should be placed in transmit buffer 1 Right channel should be placed in transmit buffer 0 Left channel currently in receive buffer 1 Right channel currently in receive buffer 4 3 2 1:0 RXLR TXIRQ RXIRQ WCNT[9:8] 0 0 0 00 R R/W1 H0 R/W1 H0 R TX interrupt flag. This bit is cleared by hardware when the I2SDATH register is written. 0 Interrupt not pending 1 Interrupt pending RX Interrupt flag. This is cleared by hardware when the I2SDATH register is read. 0 Interrupt not pending 1 Interrupt pending Upper 2 bits of the 10-bit internal word counter at the time of the last trigger 2 0xDF46: I2SCLKF0 - I S Clock Configuration Register 0 Bit Field Name Reset R/W Description 7:0 DENOM[7:0] 0x93 R/W The clock division denominator low bits 2 0xDF47: I2SCLKF1 - I S Clock Configuration Register 1 Bit Field Name Reset R/W Description 7:0 NUM[7:0] 0xE2 R/W Clock division numerator low bits 2 0xDF48: I2SCLKF2 - I S Clock Configuration Register 2 Bit Field Name Reset R/W Description 7 DENOM[8] 0 R/W Clock division denominator high bits 6:0 NUM[14:8] 0x04 R/W Clock division numerator high bits SWRS033G Page 168 of 244 CC1110Fx / CC1111Fx 12.16 USB Controller Note: The USB controller is only available on the CC1111Fx. The CC1111Fx contains a Full-Speed USB 2.0 compatible USB controller for serial communication with a PC or other equipment with USB host functionality. firmware. The firmware must be able to reply correctly to all standard requests from the USB host and work according to the protocol implemented in the driver on the PC. The USB Controller has the following features: Full-Speed operation (up to 12 Mbps) 5 endpoints (in addition to endpoint 0) that can be used as IN, OUT, or IN/OUT and can be configured as bulk/interrupt or isochronous. Note: This section will focus on describing the functionality of the USB controller, and it is assumed that the reader has a good understanding of USB and is familiar with the terms and concepts used. Refer to the Universal Serial Bus Specification for details [6]. 1 KB SRAM FIFO available for storing USB packets Endpoints supporting packet sizes from 8 - 512 bytes Standard USB nomenclature is used regarding IN and OUT. I.e., IN is always into the host (PC) and OUT is out of the host (into the CC1111Fx) Support for double buffering of USB packets The USB controller monitors the USB bus for relevant activity and handles packet transfers. The CC1111Fx will always operate as a slave on the USB bus and responds only on requests from the host (a packet can only be sent (or received) when the USB host sends a request in the form of a token). Figure 43 shows a block diagram of the USB controller. The USB PHY is the physical interface with input and output drivers. The USB SIE is the Serial Interface Engine which controls the packet transfer to/from the endpoints. The USB controller is connected to the rest of the system through the Memory Arbiter. Appropriate response to USB interrupts and loading/unloading of packets into/from endpoint FIFOs is the responsibility of the Figure 43: USB Controller Block Diagram 12.16.1 48 MHz Clock A 48 MHz external crystal must be used for the USB Controller to operate correctly. This 48 MHz clock is divided by two internally to generate a maximum system clock frequency of 24 MHz. It is important that the crystal oscillator is stable before the USB Controller is SWRS033G Page 169 of 244 CC1110Fx / CC1111Fx accessed. See 12.1.5.1 for details on how to set up the crystal oscillator. SLEEP.USB_EN controller. 12.16.2 USB Enable 12.16.3 USB Interrupts The USB Controller must be enabled before it is used. This is performed by setting the SLEEP.USB_EN bit to 1. Setting There are 3 interrupt flag registers with associated interrupt enable mask registers. to 0 will reset the USB Interrupt Flag Description Associated Interrupt Enable Mask Register USBCIF Contains flags for common USB interrupts USBCIE USBIIF Contains interrupt flags for endpoint 0 and all the IN endpoints USBIIE USBOIF Contains interrupt flags for all OUT endpoints USBOIE Note: All interrupts except SOF and suspend are initially enabled after reset Table 59: USB Interrupt Flags Interrupt Enable Mask Registers In addition to the interrupt flags in the registers shown in Table 59, there are two CPU interrupt flags associated with the USB controller; IRCON2.USBIF and IRCON.P0IF. For an interrupt request to be generated, IEN1.P0IE and/or IEN2.USBIE must be set to 1 together with the desired interrupt enable bits from the USBCIE, USBIIE, and USBOIE registers. When an interrupt request has been generated, the CPU will start executing the ISR if there are no higher priority interrupts pending. The USB controller uses interrupt #6 for USB interrupts. This interrupt number is shared with Port 2 inputs, hence the interrupt routine must also handle Port 2 interrupts if they are enabled. The interrupt routine should read all the interrupt flag registers and take action depending on the status of the flags. The interrupt flag registers will be cleared when they are read and the status of the individual interrupt flags should therefore be saved in memory (typically in a local variable on the stack) to allow them to be accessed multiple times. At the end of the ISR, after the interrupt flags have been read, the interrupt flags should be cleared to allow for new USB/P2 interrupts to be detected. The port 2 interrupt status flags in the P2IFG register should be cleared prior to clearing IRCON2.P2IF (see Section 10.5.2). Refer to Table 39 and Table 40 for a complete list of interrupts, and Section 10.5 for more details about interrupts. 12.16.3.1 USB Resume Interrupt P0_7 does not exist on the CC1111Fx, but the corresponding interrupt is used for USB resume interrupt. This means that to be able to wake up the CC1111Fx from PM1/suspend when resume signaling has been detected on the USB bus, IEN1.P0IE must be set to 1 together with PICTL.P0IENH. PICTL.P0ICON must be 0 to enable interrupts on rising edge. The P0 ISR should check the P0IFG.USB_RESUME, and resume if this bit is set to 1. If PM1 is entered from within an ISR due to a suspend interrupt, it is important that the priority of the P0 interrupt is set higher than the priority of the interrupt from which PM1 was entered. See Section 12.16.9 for more details about suspend and resume. 12.16.4 Endpoint 0 Endpoint 0 (EP0) is a bi-directional control endpoint and during the enumeration phase all communication is performed across this endpoint. Before the USBADDR register has been set to a value other than 0, the USB controller will only be able to communicate through endpoint 0. Setting the USBADDR register to a value between 1 and 127 will bring the USB function out of the Default state in the enumeration phase and into the Address state. All configured endpoints will then be available for the application. The EP0 FIFO is only used as either IN or OUT and double buffering is not provided for endpoint 0. The maximum packet size for endpoint 0 is fixed at 32 bytes. SWRS033G Page 170 of 244 CC1110Fx / CC1111Fx The USB host tries to send a packet that exceeds the maximum packet size during the OUT Data stage Endpoint 0 is controlled through the USBCS0 register by setting the USBINDEX register to 0. The USBCNT0 register contains the number of bytes received. 12.16.5 Endpoint 0 Interrupts The following events may generate an EP0 interrupt request: A data packet has been received (USBCS0.OUTPKT_RDY=1) A data packet that was loaded into the EP0 FIFO has been sent to the USB host (USBCS0.INPKT_RDY should be set to 1 when a new packet is ready to be transferred. This bit will be cleared by HW when the data packet has been sent) An IN transaction has been completed (the interrupt is generated during the Status stage of the transaction) A STALL has been (USBCS0.SENT_STALL=1) sent A control transfer ends due to a premature end of control transfer (USBCS0.SETUP_END=1) Any of these events will cause the USBIIF.EP0IF to be asserted regardless of the status of the EP0 interrupt mask bit USBIIE.EP0IE. If the EP0 interrupt mask bit is set to 1, the CPU interrupt flag IRCON2.USBIF will also be asserted. An interrupt request is only generated if IEN2.USBIE and USBIIE.EP0IE are both set to 1. 12.16.5.1 Error Conditions When a protocol error occurs, the USB controller sends a STALL handshake. The USBCS0.SENT_STALL bit is asserted and an interrupt request is generated if the endpoint 0 interrupt is properly enabled. A protocol error can be any of the following: An OUT token is received after USBCS0.DATA_END has been set to complete the OUT Data stage (the host tries to send more data than expected) An IN token is received after USBCS0.DATA_END has been set to complete the IN Data stage (the host tries to receive more data than expected) The size of the DATA1 packet received during the Status stage is not 0 The firmware can also terminate the current transaction by setting the USBCS0.SEND_STALL bit to 1. The USB controller will then send a STALL handshake in response to the next requests from the USB host. If an EP0 interrupt is caused by the assertion of the USBCS0.SENT_STALL bit, this bit should be de-asserted and firmware should consider the transfer as aborted (free memory buffers etc.). If EP0 receives an unexpected token during the Data stage, the USBCS0.SETUP_END bit will be asserted and an EP0 interrupt will be generated (if enabled properly). EP0 will then switch to the IDLE state. Firmware should then set the USBCS0.CLR_SETUP_END bit to 1 and abort the current transfer. If USBCS0.OUTPKT_RDY is asserted, this indicates that another Setup Packet has been received that firmware should process. 12.16.5.2 SETUP Transactions (IDLE State) The control transfer consists of 2 - 3 stages of transactions (Setup - Data - Status or Setup Status). The first transaction is a Setup transaction. A successful Setup transaction comprises three sequential packets (a token packet, a data packet, and a handshake packet), where the data field (payload) of the data packet is exactly 8 bytes long and are referred to as the Setup Packet. In the Setup stage of a control transfer, EP0 will be in the IDLE state. The USB controller will reject the data packet if the Setup Packet is not 8 bytes. Also, the USB controller will examine the contents of the Setup Packet to determine whether or not there is a Data stage in the control transfer. If there is a Data stage, EP0 will switch state to TX (IN transaction) or RX (OUT transaction) when the USBCS0.CLR_OUTPKT_RDY bit is set to 1 (if USBCS0.DATA_END=0). When a packet is received, the USBCS0.OUTPKT_RDY bit will be asserted and an interrupt request is generated (EP0 interrupt) if the interrupt has been enabled. Firmware should perform the following when a Setup Packet has been received: SWRS033G Page 171 of 244 CC1110Fx / CC1111Fx 1. Unload the Setup Packet from the EP0 FIFO is working, but temporarily has no data to send. 2. Examine the contents and perform the appropriate operations 12.16.5.4 OUT Transactions (RX state) 3. Set the USBCS0.CLR_OUTPKT_RDY bit to 1. This denotes the end of the Setup stage. If the control transfer has no Data stage, the USBCS0.DATA_END bit must also be set. If there is no Data stage, the USB Controller will stay in the IDLE state. 12.16.5.3 IN Transactions (TX state) If the control transfer requires data to be sent to the host, the Setup stage will be followed by one or more IN transactions in the Data stage. In this case the USB controller will be in TX state and only accept IN tokens. A successful IN transaction comprises two or three sequential packets (a token packet, a data 19 packet, and a handshake packet ). If more than 32 bytes (maximum packet size) is to be sent, the data must be split into a number of 32 byte packets followed by a residual packet. If the number of bytes to send is a multiple of 32, the residual packet will be a zero length data packet, hence a packet size less than 32 bytes denotes the end of the transfer. Firmware should load the EP0 FIFO with the first data packet and set the USBCS0.INPKT_RDY bit as soon as possible after the USBCS0.CLR_OUTPKT_RDY bit has been set. The USBCS0.INPKT_RDY will be cleared and an EP0 interrupt will be generated when the data packet has been sent. Firmware might then load more data packets as necessary. An EP0 interrupt will be generated for each packet sent. Firmware must set USBCS0.DATA_END in addition to USBCS0.INPKT_RDY when the last data packet has been loaded. This will start the Status stage of the control transfer. EP0 will switch to the IDLE state when the Status stage has completed. The Status stage may fail if the USBCS0.SEND_STALL bit is set to 1. The USBCS0.SENT_STALL bit will then be asserted and an EP0 interrupt will be generated as explained in Section 12.16.5.1. If USBCS0.INPKT_RDY is not set when receiving an IN token, the USB Controller will reply with a NAK to indicate that the endpoint If the control transfer requires data to be received from the host, the Setup stage will be followed by one or more OUT transactions in the Data stage. In this case the USB controller will be in RX state and only accept OUT tokens. A successful OUT transaction comprises two or three sequential packets (a token packet, a data packet, and a handshake 20 packet ). If more than 32 bytes (maximum packet size) is to be received, the data must be split into a number of 32 byte packets followed by a residual packet. If the number of bytes to receive is a multiple of 32, the residual packet will be a zero length data packet, hence a data packet with payload less than 32 bytes denotes the end of the transfer. The USBCS0.OUTPKT_RDY bit will be set and an EP0 interrupt will be generated when a data packet has been received. The firmware should set USBCS0.CLR_OUTPKT_RDY when the data packet has been unloaded from the EP0 FIFO. When the last data packet has been received (packet size less than 32 bytes) firmware should also set the USBCS0.DATA_END bit. This will start the Status stage of the control transfer. The size of the data packet is kept in the USBCNT0 registers. Note that this value is only valid when USBCS0.OUTPKT_RDY=1. EP0 will switch to the IDLE state when the Status stage has completed. The Status stage may fail if the DATA1 packet received is not a zero length data packet or if the USBCS0.SEND_STALL bit is set to 1. The USBCS0.SENT_STALL bit will then be asserted and an EP0 interrupt will be generated as explained in Section 12.16.5.1. 12.16.6 Endpoints 1 - 5 Each endpoint can be used as an IN only, an OUT only, or IN/OUT. For an IN/OUT endpoint there are basically two endpoints, an IN endpoint and an OUT endpoint associated with the endpoint number. Configuration and control of IN endpoints is performed through the USBCSIL and USBCSIH registers. The USBCSOL and USBCSOH registers are used to 20 19 For isochronous transfers there would not be a handshake packet from the host SWRS033G For isochronous transfers there would not be a handshake packet from the CC1111Fx Page 172 of 244 CC1110Fx / CC1111Fx configure and control OUT endpoints. Each IN and OUT endpoint can be configured as either Isochronous (USBCSIH.ISO=1 and/or USBCSOH.ISO=1) or Bulk/Interrupt (USBCSIH.ISO=0 and/or USBCSOH.ISO=0) endpoints. Bulk and Interrupt endpoints are handled identically by the USB controller but will have different properties from a firmware perspective. The USBINDEX register must have the value of the endpoint number before the Indexed Endpoint Registers are accessed (see Table 35 on Page 53). 12.16.6.1 FIFO Management Each endpoint has a certain number of FIFO memory bytes available for incoming and outgoing data packets. Table 60 shows the FIFO size for endpoints 1 - 5. It is the firmware that is responsible for setting the USBMAXI and USBMAXO registers correctly for each endpoint to prevent data from being overwritten. the OUT FIFO grows up from the bottom of the endpoint memory region. When the IN or OUT endpoint of an endpoint number use double buffering, the sum of USBMAXI and USBMAXO must not exceed half the FIFO size for the endpoint. Figure 44 b) illustrates the IN and OUT FIFO memory for an endpoint that uses double buffering. Notice that the second OUT buffer starts from the middle of the memory region and grows upwards. The second IN buffer also starts from the middle of the memory region but grows downwards. To configure an endpoint as IN only, set USBMAXO to 0 and to configure an endpoint as OUT only, set USBMAXI to 0. For unused endpoints, both USBMAXO and USBMAXI should be set to 0. When both the IN and the OUT endpoint of an endpoint number do not use double buffering, the sum of USBMAXI and USBMAXO must not exceed the FIFO size for the endpoint. Figure 44 a) shows how the IN and OUT FIFO memory for an endpoint is organized with single buffering. The IN FIFO grows down from the top of the endpoint memory region while EP Number FIFO Size (in bytes) 1 32 2 64 3 128 4 256 5 512 Table 60: FIFO Sizes for EP{1 - 5} 0 0 IN FIFO (Buffer 1) IN FIFO USBMAXI - 1 USBMAXI - 1 USBMAX0 - 1 0 0 OUT FIFO (Buffer 2) IN FIFO (Buffer 2) USBMAXI - 1 USBMAX0 - 1 USBMAX0 - 1 OUT FIFO 0 0 OUT FIFO (Buffer 1) b) a) Figure 44: IN/OUT FIFOs, a) Single Buffering b) Double Buffering 12.16.6.2 Double Buffering To enable faster transfer and reduce the need for retransmissions, CC1111Fx implements double buffering, allowing two packets to be buffered in the FIFO in each direction. This is highly recommended for isochronous endpoints, which are expected to transfer one data packet every USB frame without any retransmission. For isochronous endpoint one data packet will be sent/received every USB frame. However, the data packet may be SWRS033G Page 173 of 244 CC1110Fx / CC1111Fx sent/received at any time during the USB frame period and there is a chance that two data packets may be sent/received at a few micro seconds interval. For isochronous endpoints, an incoming packet will be lost if there is no buffer available and a zero length data packet will be sent if there is no data packet ready for transmission when the USB host requests data. Double buffering is not as critical for bulk and interrupt endpoints as it is for isochronous endpoint since packets will not be lost. Double buffering, however, may improve the effective data rate for bulk endpoints. To enable double buffering for an IN endpoint, USBCSIH.IN_DBL_BUF must be set to 1. To enable double buffering for an OUT endpoint, set USBCSOH.OUT_DBL_BUF to 1. 12.16.6.3 FIFO Access The endpoint FIFOs are accessed by reading and writing to the registers in Table 36 on Page 53. Writing to a register causes the byte written to be inserted into the IN FIFO. Reading a register causes the next byte in the OUT FIFO to be extracted and the value of this byte to be returned. When a data packet has been written to an IN FIFO, the USBCSIL.INPKT_RDY bit must be set to 1. If double buffering is enabled, the USBCSIL.INPKT_RDY bit will be cleared immediately after it has been written and another data packet can be loaded. This will not generate an IN endpoint interrupt, since an interrupt is only generated when a packet has been sent. When double buffering is used firmware should check the status of the USBCSIL.PKT_PRESENT bit before writing to the IN FIFO. If this bit is 0, two data packets can be written. Double buffered isochronous endpoints should only need to load two packets the first time the IN FIFO is loaded. After that, one packet is loaded for every USB frame. To send a zero length data packet, USBCSIL.INPKT_RDY should be set to 1 without loading a data packet into the IN FIFO. A data packet can be read from the OUT FIFO when the USBCSOL.OUTPKT_RDY bit is 1. An interrupt will be generated when this occurs, if enabled. The size of the data packet is kept in the USBCNTH:USBCNTL registers. Note that this value is only valid when USBCSOL.OUTPKT_RDY=1. When the data packet has been read from the OUT FIFO, the USBCSOL.OUTPKT_RDY bit must be cleared. If double buffering is enabled there may be two data packets in the FIFO. If another data packet is ready when the USBCSOL.OUTPKT_RDY bit is cleared the USBCSOL.OUTPKT_RDY bit will be asserted immediately and an interrupt will be generated (if enabled) to signal that a new data packet has been received. The USBCSOL.FIFO_FULL bit will be set when there are two data packets in the OUT FIFO. The AutoClear feature is supported for OUT endpoints. When enabled, the USBCSOL.OUTPKT_RDY bit is cleared automatically when USBMAXO bytes have been read from the OUT FIFO. The AutoClear feature is enabled by setting USBCSOH.AUTOCLEAR=1. The AutoClear feature can be used to reduce the time the data packet occupies the OUT FIFO buffer and is typically used for bulk endpoints. A complementary AutoSet feature is supported for IN endpoints. When enabled, the USBCSIL.INPKT_RDY bit is set automatically when USBMAXI bytes have been written to the IN FIFO. The AutoSet feature is enabled by setting USBCSIH.AUTOSET=1. The AutoSet feature can reduce the overall time it takes to send a data packet and is typically used for bulk endpoints. 12.16.6.4 Endpoint 1 - 5 Interrupts The following events may generate an IN EPx interrupt request (x indicates the endpoint number): A data packet that was loaded into the IN FIFO has been sent to the USB host (USBCSIL.INPKT_RDY should be set to 1 when a new packet is ready to be transferred. This bit will be cleared by HW when the data packet has been sent) A STALL has been sent (USBCSIL.SENT_STALL=1). Only Bulk/Interrupt endpoints can be stalled The IN FIFO is flushed due to the USBCSIH.FLUSH_PACKET bit being set to 1 Any of these events will cause USBIIF.INEPxIF to be asserted regardless of the status of the IN EPx interrupt mask bit USBIIE.INEPxIE. If the IN EPx interrupt mask bit is set to 1, the CPU interrupt flag IRCON2.USBIF will also be asserted. An interrupt request is only generated if IEN2.USBIE and USBIIE.INEPxIE are both set to 1. The x in the register names refer to the endpoint number 1 - 5) SWRS033G Page 174 of 244 CC1110Fx / CC1111Fx The following events may generate an OUT EPx interrupt request: A data packet has been received (USBCSOL.OUTPKT_RDY=1) A STALL has been sent (USBCSIL.SENT_STALL=1). Only Bulk/Interrupt endpoints can be stalled Any of these events will cause USBOIF.OUTEPxIF to be asserted regardless of the status of the OUT EPx interrupt mask bit USBOIE.OUTEPxIE. If the OUT EPx interrupt mask bit is set to 1, the CPU interrupt flag IRCON2.USBIF will also be asserted. An interrupt request is only generated if IEN2.USBIE and USBOIE.OUTEPxIE are both set to 1. 12.16.6.5 Bulk/Interrupt IN Endpoint Interrupt IN transfers occur at regular intervals while bulk IN transfers utilize available bandwidth not allocated to isochronous, interrupt, or control transfers. Interrupt IN endpoints may set the USBCSIH.FORCE_DATA_TOG bit. When this bit is set the data toggle bit is continuously toggled regardless of whether an ACK was received or not. This feature is typically used by interrupt IN endpoints that are used to communicate rate feedback for Isochronous endpoints. A Bulk/Interrupt IN endpoint can be stalled by setting the USBCSIL.SEND_STALL bit to 1. When the endpoint is stalled, the USB controller will respond with a STALL handshake to IN tokens. The USBCSIL.SENT_STALL bit will then be set and an interrupt will be generated, if enabled. A bulk transfer longer than the maximum packet size is performed by splitting the transfer into a number of data packets of maximum size followed by a smaller data packet containing the remaining bytes. If the transfer length is a multiple of the maximum packet size, a zero length data packet is sent last. This means that a packet with a size less than the maximum packet size denotes the end of the transfer. The AutoSet feature can be useful in this case, since many data packets will be of maximum size. 12.16.6.6 Isochronous IN Endpoint An Isochronous IN endpoint is used to transfer periodic data from the USB controller to the host (one data packet every USB frame). If there is no data packet loaded in the IN FIFO when the USB host requests data, the USB controller sends a zero length data packet and the USBCSIL.UNDERRUN bit will be asserted. Double buffering requires that a data packet is loaded into the IN FIFO during the frame preceding the frame where it should be sent. If the first data packet is loaded before an IN token is received, the data packet will be sent during the same frame as it was loaded and hence violate the double buffering strategy. Thus, when double buffering is used, the USBPOW.ISO_WAIT_SOF bit should be set to 1 to avoid this. Setting this bit will ensure that a loaded data packet is not sent until the next SOF token has been received. The AutoSet feature will typically not be used for isochronous endpoints since the packet size will increase or decrease from frame to frame. 12.16.6.7 Bulk/Interrupt OUT Endpoint Interrupt OUT transfers occur at regular intervals while bulk OUT transfers utilize available bandwidth not allocated to isochronous, interrupt, or control transfers. A Bulk/Interrupt OUT endpoint can be stalled by setting the USBCSOL.SEND_STALL bit to 1. When the endpoint is stalled, the USB controller will respond with a STALL handshake when the host is done sending the data packet. The data packet is discarded and is not placed in the OUT FIFO. The USB controller will assert the USBCSOL.SENT_STALL bit when the STALL handshake is sent and generate an interrupt request if the OUT endpoint interrupt is enabled. As the AutoSet feature is useful for bulk IN endpoints, the AutoClear feature is useful for OUT endpoints since many packets will be of maximum size. 12.16.6.8 Isochronous OUT Endpoint An Isochronous OUT endpoint is used to transfer periodic data from the host to the USB controller (one data packet every USB frame). If there is no buffer available when a data packet is being received, the USBCSOL.OVERRUN bit will be asserted and the packet data will be lost. Firmware can reduce the chance for this to happen by using double buffering and use DMA to effectively unload data packets. SWRS033G Page 175 of 244 CC1110Fx / CC1111Fx An isochronous data packet in the OUT FIFO may have bit errors. The hardware will detect this condition and set USBCSOL.DATA_ERROR. Firmware should therefore always check this bit when unloading a data packet. The AutoClear feature will typically not be used for isochronous endpoints since the packet size will increase or decrease from frame to frame. 12.16.7 DMA DMA should be used to fill the IN endpoint FIFOs and empty the OUT endpoint FIFOs. Using DMA will improve the read/write performance significantly compared to using the 8051 CPU. It is therefore highly recommended to use DMA unless timing is not critical or only a few bytes are to be transferred. There are no DMA triggers for the USB controller, meaning that DMA transfers must be triggered by firmware. The word size can be byte (8 bits) or word (16 bits). When word size transfer is used the ENDIAN register must be set correctly (see Section 12.5.7). The ENDIAN.USBRLE bit selects whether a word is read as little or big endian from the OUT FIFOs and the ENDIAN.USBWLE bit selects whether a word is written as little or big endian to the IN FIFOs. Writing and reading words for the different settings is shown in Figure 45 and Figure 46 respectively. Notice that the setting for these bits will be used for all endpoints. Consequently, it is not possible to have multiple DMA channels active at once that use different endianness. The ENDIAN register must be configured to use big endian for both read and write for a word size transfer to produce the same result as a byte size transfer of an even number of bytes. Word size transfers are slightly more efficient than byte transfers. Refer to Section regarding DMA. 12.5 for more details Figure 45: Writing Big/Little Endian Figure 46: Reading Big/Little Endian SWRS033G Page 176 of 244 CC1110Fx / CC1111Fx 12.16.8 USB Reset When reset signaling is detected on the bus, the USBCIF.RSTIF flag will be asserted. If USBCIE.RSTIE is enabled, IRCON2.USBIF will also be asserted and an interrupt request is generated if IEN2.USBIE=1. The firmware should take appropriate action when a USB reset occurs. A USB reset should place the device in the Default state where it will only respond to address 0 (the default address). One or more resets will normally take place during the enumeration phase right after the USB cable is connected. The following actions are performed by the USB controller when a USB reset occurs: USBADDR is set to 0 USBINDEX is set to 0 All endpoint FIFOs are flushed USBCS0, USBCSIL, USBCSIH, USBCSOL, USBCSOH are cleared. All interrupts, except SOF and suspend, are enabled An interrupt request is generated (if IEN2.USBIE=1 and USBCIE.RSTIE=1) Firmware should close all pipes and wait for a new enumeration phase when USB reset is detected. 12.16.9 Suspend and Resume The USB controller will assert USBCIF.SUSPENDIF and enter suspend mode when the USB bus has been continuously idle for 3 ms, provided that USBPOW.SUSPEND_EN=1. IRCON2.USBIF will be asserted if USBCIE.SUSPENDIE is enabled, and an interrupt request is generated if IEN2.USBIE=1. While in suspend mode, only limited current can be sourced from the USB bus. See the USB 2.0 Specification [6] for details about this. To be able to meet the suspend-current requirement, the CC1111Fx should be taken down to PM1 when suspend is detected. The CC1111Fx should not enter PM2 or PM3 since this will reset the USB controller. Any valid non-idle signaling on the USB bus will cause the USBCIF.RESUMEIF to be asserted and an interrupt request to be generated and wake up the system if the USB resume interrupt is configured correctly. Refer to 12.16.3.1 for details about how to set up the USB resume interrupt. Any valid non-idle signaling on the USB bus will cause the USBCIF.RESUMEIF to be asserted and an interrupt request to be generated and wake up the system if the USB resume interrupt is configured correctly. Refer to 12.16.3.1 for details about how to set up the USB resume interrupt. When the system wakes up (enters active mode) from suspend, no USB registers must be accessed before the 48 MHZ crystal oscillator has stabilized. A USB reset will also wake up the system from suspend. A USB resume interrupt request will be generated, if the interrupt is configured as described in 12.16.3.1, but the USBCIF.RSTIF interrupt flag will be set instead of the USBCIF.RESUMEIF interrupt flag. 12.16.10 Remote Wakeup The USB controller can resume from suspend by signaling resume to the USB hub. Resume is performed by setting USBPOW.RESUME to 1 for approximately 10 ms. According to the USB 2.0 Specification [6], the resume signaling must be present for at least 1 ms and no more than 15 ms. It is, however, recommended to keep the resume signaling for approximately 10 ms. Notice that support for remote wakeup must be declared in the USB descriptor, and that the USB host must grant the device the privilege to perform remote wakeup (through a SET_FEATURE request). 12.16.11 USB Registers This section describes all USB registers used for control and status for the USB. The USB registers reside in XDATA memory space in the region 0xDE00 - 0xDE3F. These registers can be divided into three groups: The Common USB Registers, the Indexed Endpoint Registers, and the Endpoint FIFO Registers. Table 34, Table 35, and Table 36 give an overview of the registers in the three groups respectively, while the remaining of this section will describe each register in detail. The Indexed Endpoint Registers represent the currently selected endpoint. The USBINDEX register is used to select the endpoint. Notice that the upper register addresses 0xDE2C - 0xDE3F are reserved. SWRS033G Page 177 of 244 CC1110Fx / CC1111Fx 0xDE00: USBADDR - Function Address Bit Field Name Reset R/W Description 7 UPDATE 0 R This bit is set when the USBADDR register is written and cleared when the address becomes effective. 6:0 USBADDR[6:0] 0000000 R/W Device address 0xDE01: USBPOW - Power/Control Register Bit Field Name Reset R/W Description 7 ISO_WAIT_SOF 0 R/W When this bit is set to 1, the USB controller will send zero length data packets from the time INPKT_RDY is asserted and until the first SOF token has been received. This only applies to isochronous endpoints. 6:4 - R0 Not used 3 RST 0 R During reset signaling, this bit is set to1 2 RESUME 0 R/W Drive resume signaling for remote wakeup. According to the USB Specification the duration of driving resume must be at least 1 ms and no more than 15 ms. It is recommended to keep this bit set for approximately 10 ms. 1 SUSPEND 0 R Suspend mode entered. This bit will only be used when SUSPEND_EN=1. Reading the USBCIF register or asserting RESUME will clear this bit. 0 SUSPEND_EN 0 R/W Suspend Enable. When this bit is set to 1, suspend mode will be entered when USB bus has been idle for 3 ms. 0xDE02: USBIIF - IN Endpoints and EP0 Interrupt Flags Bit Field Name 7:6 Reset R/W Description 00 R0 Reserved 5 INEP5IF 0 R H0 Interrupt flag for IN endpoint 5. Cleared by HW when read 4 INEP4IF 0 R H0 Interrupt flag for IN endpoint 4. Cleared by HW when read 3 INEP3IF 0 R H0 Interrupt flag for IN endpoint 3. Cleared by HW when read 2 INEP2IF 0 R H0 Interrupt flag for IN endpoint 2. Cleared by HW when read 1 INEP1IF 0 R H0 Interrupt flag for IN endpoint 1. Cleared by HW when read 0 EP0IF 0 R H0 Interrupt flag for endpoint 0. Cleared by HW when read 0xDE04: USBOIF - Out Endpoints Interrupt Flags Bit Field Name 7:6 Reset R/W Description 00 R0 Reserved 5 OUTEP5IF 0 R H0 Interrupt flag for OUT endpoint 5. Cleared by HW when read 4 OUTEP4IF 0 R H0 Interrupt flag for OUT endpoint 4. Cleared by HW when read 3 OUTEP3IF 0 R H0 Interrupt flag for OUT endpoint 3. Cleared by HW when read 2 OUTEP2IF 0 R H0 Interrupt flag for OUT endpoint 2. Cleared by HW when read 1 OUTEP1IF 0 R H0 Interrupt flag for OUT endpoint 1. Cleared by HW when read - R0 Not used 0 SWRS033G Page 178 of 244 CC1110Fx / CC1111Fx 0xDE06: USBCIF - Common USB Interrupt Flags Bit Field Name 7:4 Reset R/W Description - R0 Not used 3 SOFIF 0 R H0 Start-Of-Frame interrupt flag. Cleared by HW when read 2 RSTIF 0 R H0 Reset interrupt flag. Cleared by HW when read 1 RESUMEIF 0 R H0 Resume interrupt flag. Cleared by HW when read 0 SUSPENDIF 0 R H0 Suspend interrupt flag. Cleared by HW when read 0xDE07: USBIIE - IN Endpoints and EP0 Interrupt Enable Mask Bit Field Name 7:6 5 4 3 2 1 0 INEP5IE INEP4IE INEP3IE INEP2IE INEP1IE EP0IE Reset R/W Description 00 R/W Reserved. Always write 00 1 R/W IN endpoint 5 interrupt enable 1 1 1 1 1 R/W R/W R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled IN endpoint 4 interrupt enable 0 Interrupt disabled 1 Interrupt enabled IN endpoint 3 interrupt enable 0 Interrupt disabled 1 Interrupt enabled IN endpoint 2 interrupt enable 0 Interrupt disabled 1 Interrupt enabled IN endpoint 1 interrupt enable 0 Interrupt disabled 1 Interrupt enabled Endpoint 0 interrupt enable 0 Interrupt disabled 1 Interrupt enabled SWRS033G Page 179 of 244 CC1110Fx / CC1111Fx 0xDE09: USBOIE - Out Endpoints Interrupt Enable Mask Bit Field Name 7:6 5 4 3 2 1 OUTEP5IE OUTEP4IE OUTEP3IE OUTEP2IE OUTEP1IE 0 Reset R/W Description 00 R/W Reserved. Always write 00 1 R/W OUT endpoint 5 interrupt enable 1 1 1 1 - R/W R/W R/W R/W R0 0 Interrupt disabled 1 Interrupt enabled OUT endpoint 4 interrupt enable 0 Interrupt disabled 1 Interrupt enabled OUT endpoint 3 interrupt enable 0 Interrupt disabled 1 Interrupt enabled OUT endpoint 2 interrupt enable 0 Interrupt disabled 1 Interrupt enabled OUT endpoint 1 interrupt enable 0 Interrupt disabled 1 Interrupt enabled Not used 0xDE0B: USBCIE - Common USB Interrupt Enable Mask Bit Field Name 7:4 3 2 1 0 SOFIE RSTIE RESUMEIE SUSPENDIE Reset R/W Description - R0 Not used 0 R/W Start-Of-Frame interrupt enable 1 1 0 R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled Reset interrupt enable 0 Interrupt disabled 1 Interrupt enabled Resume interrupt enable 0 Interrupt disabled 1 Interrupt enabled Suspend interrupt enable 0 Interrupt disabled 1 Interrupt enabled 0xDE0C: USBFRML - Current Frame Number (Low byte) Bit Field Name Reset R/W Description 7:0 FRAME[7:0] 0x00 R Low byte of 11-bit frame number SWRS033G Page 180 of 244 CC1110Fx / CC1111Fx 0xDE0D: USBFRMH - Current Frame Number (High byte) Bit Field Name 7:3 2:0 FRAME[10:8] Reset R/W Description - R0 Not used 000 R 3 MSB of 11-bit frame number 0xDE0E: USBINDEX - Current Endpoint Index Register Bit Field Name 7:4 3:0 USBINDEX[3:0] Reset R/W Description - R0 Not used 0000 R/W Endpoint selected. Must be set to value in the range 0 - 5 0xDE10: USBMAXI - Max. Packet Size for IN Endpoint{1 - 5} Bit Field Name Reset R/W Description 7:0 USBMAXI[7:0] 0x00 R/W Maximum packet size in units of 8 bytes for IN endpoint selected by USBINDEX register. The value of this register should correspond to the wMaxPacketSize field in the Standard Endpoint Descriptor for the endpoint. This register must not be set to a value grater than the available FIFO memory for the endpoint. 0xDE11: USBCS0 - EP0 Control and Status (USBINDEX=0) Bit Field Name Reset R/W Description 7 CLR_SETUP_END 0 R/W H0 Set this bit to 1 to de-assert the SETUP_END bit of this register. This bit will be cleared automatically. 6 CLR_OUTPKT_RDY 0 R/W H0 Set this bit to 1 to de-assert the OUTPKT_RDY bit of this register. This bit will be cleared automatically. 5 SEND_STALL 0 R/W H0 Set this bit to 1 to terminate the current transaction. The USB controller will send the STALL handshake and this bit will be de-asserted. 4 SETUP_END 0 R This bit is set if the control transfer ends due to a premature end of control transfer. The FIFO will be flushed and an interrupt request (EP0) will be generated if the interrupt is enabled. Setting CLR_SETUP_END=1 will deassert this bit 3 DATA_END 0 R/W H0 This bit is used to signal the end of a data transfer and must be asserted in the following three situations: 1 When the last data packet has been loaded and USBCS0.INPKT_RDY is set to 1 2 When the last data packet has been unloaded and USBCS0.CLR_OUTPKT_RDY is set to 1 3 When USBCS0.INPKT_RDY has been asserted without having loaded the FIFO (for sending a zero length data packet). The USB controller will clear this bit automatically 2 SENT_STALL 0 R/W H1 This bit is set when a STALL handshake has been sent. An interrupt request (EP0) will be generated if the interrupt is enabled This bit must be cleared from firmware. 1 INPKT_RDY 0 R/W H0 Set this bit when a data packet has been loaded into the EP0 FIFO to notify the USB controller that a new data packet is ready to be transferred. When the data packet has been sent, this bit is cleared and an interrupt request (EP0) will be generated if the interrupt is enabled. 0 OUTPKT_RDY 0 R Data packet received. This bit is set when an incoming data packet has been placed in the OUT FIFO. An interrupt request (EP0) will be generated if the interrupt is enabled. Set CLR_OUTPKT_RDY=1 to de-assert this bit. SWRS033G Page 181 of 244 CC1110Fx / CC1111Fx 0xDE11: USBCSIL - IN EP{1 - 5} Control and Status Low Bit Field Name 7 Reset R/W Description - R0 Not used 6 CLR_DATA_TOG 0 R/W H0 Setting this bit will reset the data toggle to 0. Thus, setting this bit will force the next data packet to be a DATA0 packet. This bit is automatically cleared. 5 SENT_STALL 0 R/W This bit is set when a STALL handshake has been sent. The FIFO will be flushed and the INPKT_RDY bit in this register will be de-asserted. An interrupt request (IN EP{1 - 5}) will be generated if the interrupt is enabled. This bit must be cleared from firmware. 4 SEND_STALL 0 R/W Set this bit to 1 to make the USB controller reply with a STALL handshake when receiving IN tokens. Firmware must clear this bit to end the STALL condition. It is not possible to stall an isochronous endpoint, thus this bit will only have effect if the IN endpoint is configured as bulk/interrupt. 3 FLUSH_PACKET 0 R/W H0 Set to 1 to flush next packet that is ready to transfer from the IIN FIFO. The INPKT_RDY bit in this register will be cleared. If there are two packets in the IN FIFO due to double buffering, this bit must be set twice to completely flush the IN FIFO. This bit is automatically cleared. 2 UNDERRUN 0 R/W In isochronous mode, this bit is set if an IN token is received when INPKT_RDY=0, and a zero length data packet is transmitted in response to the IN token. In Bulk/Interrupt mode, this bit is set when a NAK is returned in response to an IN token. Firmware should clear this bit. 1 PKT_PRESENT 0 R This bit is 1 when there is at least one packet in the IN FIFO. 0 INPKT_RDY 0 R/W H0 Set this bit when a data packet has been loaded into the IN FIFO to notify the USB controller that a new data packet is ready to be transferred. When the data packet has been sent, this bit is cleared and an interrupt request (IN EP{1 - 5}) will be generated if the interrupt is enabled. 0xDE12: USBCSIH - IN EP{1 - 5} Control and Status High Bit Field Name Reset R/W Description 7 AUTOSET 0 R/W When this bit is 1, the USBCSIL.INPKT_RDY bit is automatically asserted when a data packet of maximum size (specified by USBMAXI) has been loaded into the IN FIFO. 6 ISO 0 R/W Selects IN endpoint type 5:4 3 FORCE_DATA_TOG 2:1 0 IN_DBL_BUF 0 Bulk/Interrupt 1 Isochronous 10 R/W Reserved. Always write 10 0 R/W Setting this bit will force the IN endpoint data toggle to switch and the data packet to be flushed from the IN FIFO even though an ACK was received. This feature can be useful when reporting rate feedback for isochronous endpoints. - R0 Not used 0 R/W Double buffering enable (IN FIFO) 0 Double buffering disabled 1 Double buffering enabled 0xDE13: USBMAXO - Max. Packet Size for OUT{1 - 5} Endpoint Bit Field Name Reset R/W Description 7:0 USBMAXO[7:0] 0x00 R/W Maximum packet size in units of 8 bytes for OUT endpoint selected by USBINDEX register. The value of this register should correspond to the wMaxPacketSize field in the Standard Endpoint Descriptor for the endpoint. This register must not be set to a value grater than the available FIFO memory for the endpoint. SWRS033G Page 182 of 244 CC1110Fx / CC1111Fx 0xDE14: USBCSOL - OUT EP{1 - 5} Control and Status Low Bit Field Name Reset R/W Description 7 CLR_DATA_TOG 0 R/W H0 Setting this bit will reset the data toggle to 0. Thus, setting this bit will force the next data packet to be a DATA0 packet. This bit is automatically cleared. 6 SENT_STALL 0 R/W This bit is set when a STALL handshake has been sent. An interrupt request (OUT EP{1 - 5}) will be generated if the interrupt is enabled. This bit must be cleared from firmware 5 SEND_STALL 0 R/W Set this bit to 1 to make the USB controller reply with a STALL handshake when receiving OUT tokens. Firmware must clear this bit to end the STALL condition. It is not possible to stall an isochronous endpoint, thus this bit will only have effect if the IN endpoint is configured as bulk/interrupt. 4 FLUSH_PACKET 0 R/W H0 Set to 1 to flush next packet that is to be read from the OUT FIFO. The OUTPKT_RDY bit in this register will be cleared. If there are two packets in the OUT FIFO due to double buffering, this bit must be set twice to completely flush the OUT FIFO. This bit is automatically cleared. 3 DATA_ERROR 0 R This bit is set if there is a CRC or bit-stuff error in the packet received. Cleared when OUTPKT_RDY is cleared. This bit will only be valid if the OUT endpoint is isochronous. 2 OVERRUN 0 R/W This bit is set when an OUT packet cannot be loaded into the OUT FIFO. Firmware should clear this bit. This bit is only valid in isochronous mode 1 FIFO_FULL 0 R This bit is asserted when no more packets can be loaded into the OUT FIFO full. 0 OUTPKT_RDY 0 R/W This bit is set when a packet has been received and is ready to be read from OUT FIFO. An interrupt request (OUT EP{1 - 5}) will be generated if the interrupt is enabled. This bit should be cleared when the packet has been unloaded from the FIFO. 0xDE15: USBCSOH - OUT EP{1 - 5} Control and Status High Bit Field Name Reset R/W Description 7 AUTOCLEAR 0 R/W When this bit is set to 1, the USBCSOL.OUTPKT_RDY bit is automatically cleared when a data packet of maximum size (specified by USBMAXO) has been unloaded to the OUT FIFO. 6 ISO 0 R/W Selects OUT endpoint type 0 Bulk/Interrupt 1 Isochronous 5:4 00 R/W Reserved. Always write 00 3:1 - R0 Not used 0 R/W Double buffering enable (OUT FIFO) 0 OUT_DBL_BUF 0 Double buffering disabled 1 Double buffering enabled 0xDE16: USBCNT0 - Number of Received Bytes in EP0 FIFO (USBINDEX=0) Bit Field Name 7:6 5:0 USBCNT0[5:0] Reset R/W Description - R0 Not used 000000 R Number of received bytes into EP 0 FIFO. Only valid when OUTPKT_RDY is asserted 0xDE16: USBCNTL - Number of Bytes in EP{1 - 5} OUT FIFO Low Bit Field Name Reset R/W Description 7:0 USBCNT[7:0] 0x00 R 8 LSB of number of received bytes into OUT FIFO selected by USBINDEX register. Only valid when USBCSOL.OUTPKT_RDY is asserted. SWRS033G Page 183 of 244 CC1110Fx / CC1111Fx 0xDE17: USBCNTH - Number of Bytes in EP{1 - 5} OUT FIFO High Bit Field Name 7:3 2:0 USBCNT[10:8] Reset R/W Description - R0 Not used 000 R 3 MSB of number of received bytes into OUT FIFO selected by USBINDEX register. Only valid when USBCSOL.OUTPKT_RDY is set 0xDE20: USBF0 - Endpoint 0 FIFO Bit Field Name Reset R/W Description 7:0 USBF0[7:0] 0x00 R/W Endpoint 0 FIFO. Reading this register unloads one byte from the EP0 FIFO. Writing to this register loads one byte into the EP0 FIFO. Note: The FIFO memory for EP0 is used for both incoming and outgoing data packets. 0xDE22: USBF1 - Endpoint 1 FIFO Bit Field Name Reset R/W Description 7:0 USBF1[7:0] 0x00 R/W Endpoint 1 FIFO register. Reading this register unloads one byte from the EP1 OUT FIFO. Writing to this register loads one byte into the EP1 IN FIFO. 0xDE24: USBF2 - Endpoint 2 FIFO Bit Field Name Reset R/W Description 7:0 USBF2[7:0] 0x00 R/W See Endpoint 1 FIFO description. 0xDE26: USBF3 - Endpoint 3 FIFO Bit Field Name Reset R/W Description 7:0 USBF3[7:0] 0x00 R/W See Endpoint 1 FIFO description. 0xDE28: USBF4 - Endpoint 4 FIFO Bit Field Name Reset R/W Description 7:0 USBF4[7:0] 0x00 R/W See Endpoint 1 FIFO description. 0xDE2A: USBF5 - Endpoint 5 FIFO Bit Field Name Reset R/W Description 7:0 USBF5[7:0] 0x00 R/W See Endpoint 1 FIFO description. SWRS033G Page 184 of 244 CC1110Fx / CC1111Fx 13 Radio RF_P FREQ SYNTH 0 RF_N MODULATOR 90 PA CPU INTERFACE ADC PACKET HANDLER LNA FEC / INTERLEAVER ADC DEMODULATOR RADIO CONTROL Figure 47: CC1110Fx/CC1111Fx Radio Module A simplified block diagram of the radio module in the CC1110Fx/CC1111Fx is shown in Figure 47. CC1110Fx/CC1111Fx features a low-IF receiver. The received RF signal is amplified by the lownoise amplifier (LNA) and down-converted in quadrature (I and Q) to the intermediate frequency (IF). At IF, the I/Q signals are digitized by the ADCs. Automatic gain control (AGC), fine channel filtering, demodulation bit/packet synchronization are performed digitally. The transmitter part of CC1110Fx/CC1111Fx is based on direct synthesis of the RF frequency. The frequency synthesizer includes a completely on-chip LC VCO and a 90 degrees phase shifter for generating the I and Q LO signals to the down-conversion mixers in receive mode. The 26/48 MHz crystal oscillator generates the reference frequency for the synthesizer, as well as clocks for the ADC and the digital part. An SFR interface is used for data buffer access from the CPU. Configuration and status registers are accessed through registers mapped to XDATA memory. The digital baseband includes support for channel configuration, packet handling, and data buffering. Note: In this section of the document, fRef is used to denote the reference frequency for the synthesizer. For CC1110Fx f ref f XOSC and for CC1111Fx, f ref f XOSC 2 13.1 Command Strobes The CPU uses a set of command strobes to control operation of the radio. Command strobes may be viewed as single byte instructions which each start an internal sequence in the radio. These command strobes are used to enable the frequency synthesizer, enable receive mode, enable transmit mode, etc. (see Figure 48). Note: An SIDLE strobe will clear all pending command strobes until IDLE state is reached. This means that if for example an SIDLE strobe is issued while the radio is in RX state, any other command strobes issued before the radio reached IDLE state will be ignored. The 6 command strobes are listed in Table 61 on Page 187. SWRS033G Page 185 of 244 CC1110Fx / CC1111Fx . Figure 48: Simplified State Diagram with Typical Usage and Current Consumption in Radio at 250 kBaud Data Rate and MDMCFG2.DEM_DCFILT_OFF=1 (current optimized) SWRS033G Page 186 of 244 CC1110Fx / CC1111Fx RFST Value Command Strobe Name Description 0x00 SFSTXON Enable and calibrate frequency synthesizer (if MCSM0.FS_AUTOCAL=01). If in RX (with CCA): Go to a wait state where only the synthesizer is running (for quick RX / TX turnaround). 0x01 SCAL Calibrate frequency synthesizer and turn it off. SCAL can be strobed from IDLE mode without setting manual calibration mode (MCSM0.FS_AUTOCAL=00) 0x02 SRX Enable RX. Perform calibration first if coming from IDLE and MCSM0.FS_AUTOCAL=01. 0x03 STX In IDLE state: Enable TX. Perform calibration first if MCSM0.FS_AUTOCAL=01. If in RX state and CCA is enabled: Only go to TX if channel is clear. 0x04 SIDLE Enter IDLE state (frequency synthesizer turned off). All others SNOP No operation. Table 61: Command Strobes 13.2 Radio Registers The operation of the radio is configured through a set of RF registers. These RF registers are mapped to XDATA memory space as shown in Figure 14 on Page 43 . In addition to configuration registers, the RF registers also provide status information from the radio. Section 10.2.3.4 on Page 50 gives a full description of all RF registers. 13.3 Interrupts There are two interrupt vector assigned to the radio. These are the RFTXRX interrupt (interrupt #0) and the RF interrupt (interrupt #16): RFTXRX: RX data ready or TX data complete (related to the RFD register) issued, meaning that one can not write to the RFD register before issuing an STX strobe. For an interrupt request to be generated when TCON.RFTXRXIF is asserted, IEN0.RFTXRXIE must be 1. Note: When append status is enabled, PKTCTRL1.APPEND_STATUS=1, reading status byte 1 (see Section 13.8) from the RFD register will trigger the assertion of the RFTXRXIF flag for status byte 2. If this flag is cleared AFTER reading status byte 1, the new flag will be cleared as well. One RFTXRXIF assertion will therefore be missed by software. After assertion of the RFTXRXIF flag one should therefore clear the flag BEFORE reading the RFD register. RF: All other general RF interrupts The RF interrupt vector combines the interrupts shown in the RFIM register shown on Page 189. Note that these RF interrupts are rising-edge triggered meaning that an interrupt is generated when e.g. the SFD status flag goes from 0 to 1. The RF interrupt flags are described in the next section. 13.3.1 13.3.1.1 Interrupt Registers 13.3.1.2 RFTXRX The RFTXRX interrupt is related to the RFD register. The CPU interrupt flag RFTXRXIF found in the TCON register is asserted when there are data in the RFD register ready to be read (RX), and when a new byte can be written (TX). In TX, the RFTXRXIF flag will not be asserted before an STX strobe has been RF There are 8 different events that can generate an RF interrupt request. These events are: SWRS033G TX underflow RX overflow RX timeout Packet received/transmitted. Also used to detect overflow/underflow conditions Page 187 of 244 CC1110Fx / CC1111Fx CS PQT reached CCA SFD Each of these events has a corresponding interrupt flag in the RFIF register which is asserted when the event occurs. If the corresponding mask bit is set in the RFIM register, the CPU interrupt flag S1CON.RFIF will also be asserted in addition to the interrupt flag in RFIF. If IEN2.RFIE=1 when S1CON.RFIF is asserted, and interrupt request will be generated. Refer to 0 for details about the interrupts. RFIF (0xE9) - RF Interrupt Flags Bit Field Name Reset R/W Description 7 IRQ_TXUNF 0 R/W0 TX underflow 6 5 4 3 2 1 0 IRQ_RXOVF IRQ_TIMEOUT IRQ_DONE IRQ_CS IRQ_PQT IRQ_CCA IRQ_SFD 0 0 0 0 0 0 0 R/W0 R/W0 R/W0 R/W0 R/W0 R/W0 R/W0 0 No interrupt pending 1 Interrupt pending RX overflow 0 No interrupt pending 1 Interrupt pending RX timeout, no packet has been received in the programmed period 0 No interrupt pending 1 Interrupt pending Packet received/transmitted. Also used to detect underflow/overflow conditions 0 No interrupt pending 1 Interrupt pending Carrier sense 0 No interrupt pending 1 Interrupt pending Preamble quality threshold reached 0 No interrupt pending 1 Interrupt pending Clear Channel Assessment 0 No interrupt pending 1 Interrupt pending Start of Frame Delimiter, sync word detected 0 No interrupt pending 1 Interrupt pending SWRS033G Page 188 of 244 CC1110Fx / CC1111Fx RFIM (0x91) - RF Interrupt Mask Bit Field Name Reset R/W Description 7 IM_TXUNF 0 R/W TX underflow 6 5 4 3 2 1 0 IM_RXOVF IM_TIMEOUT IM_DONE IM_CS IM_PQT IM_CCA IM_SFD 0 0 0 0 0 0 0 R/W R/W R/W R/W R/W R/W R/W 0 Interrupt disabled 1 Interrupt enabled RX overflow 0 Interrupt disabled 1 Interrupt enabled RX timeout, no packet has been received in the programmed period. 0 Interrupt disabled 1 Interrupt enabled Packet received/transmitted. Also used to detect underflow/overflow conditions 0 Interrupt disabled 1 Interrupt enabled Carrier sense 0 Interrupt disabled 1 Interrupt enabled Preamble quality threshold reached. 0 Interrupt disabled 1 Interrupt enabled Clear Channel Assessment 0 Interrupt disabled 1 Interrupt enabled Start of Frame Delimiter, sync word detected 0 Interrupt disabled 1 Interrupt enabled 13.4 TX/RX Data Transfer Data to transmit is written to the RF Data register, RFD. Received data is read from the same register. The RFD register can be viewed as a 1 byte FIFO. That means that if a byte is received in the RFD register, and it is not read before the next byte is received, the radio will enter RX_OVERFLOW state and the RFIF.IRQ_RXOVF flag will be set together with RFIF.IRQ_DONE. In TX, the radio will enter TX_UNDERFLOW state (RFIF.IRQ_TXUVF and RFIF.IRQ_DONE will be asserted) if too few bytes are written to the RFD register compared to what the radio expect. Note that if an STX strobe is issued but no data is written to the RFD register after the following assertion of the RFTXRXIF flag, the radio will start sending preamble without entering TX_UNDERFLOW state. To exit RX_OVERFLOW and/or TX_UNDERFLOW state, an SIDLE strobe command should be issued. Note: The RFD register content will not be retained in PM2 and PM3 RX and TX FIFOs can be implemented in memory and it is recommended to use the DMA to transfer data between the FIFOs and the RF Data register, RFD. The DMA channel used to transfer received data to memory when the radio is in RX mode would have RFD as the source (SRCADDR[15:0]), the RX FIFO in memory as destination (DRSTADDR[15:0]), and RADIO as DMA trigger (TRIG[4:0]). For description on the usage of DMA, refer to Section 12.5 on Page 101. SWRS033G Page 189 of 244 CC1110Fx / CC1111Fx A simple example of transmitting data is shown in Figure 49. This example does not use DMA. ; Transmit the following data: 0x02, 0x12, 0x34 ; (Assume that the radio has already been configured, the high speed ; crystal oscillator is selected as system clock, and CLKCON.CLKSPD=000) C1: C2: C3: MOV JNB CLR MOV JNB CLR MOV JNB CLR MOV RFST,#03H RFTXRXIF,C1 RFTXRXIF RFD,#02H RFTXRXIF,C2 RFTXRXIF RFD,#12H RFTXRXIF,C3 RFTXRXIF RFD,#34H ; ; ; ; ; ; ; ; ; ; ; Start TX with STX command strobe Wait for interrupt flag telling radio is ready to accept data, then write first data byte to radio (packet length = 2) Wait for radio Send first byte in payload Wait for radio Send second byte in payload Done Figure 49: Simple RF Transmit Example 13.5 Data Rate Programming R 2 20 DRATE _ E log 2 DATA f ref 28 RDATA 2 DRATE _ M 256 f ref 2 DRATE _ E The data rate used when transmitting, or the data rate expected in receive is programmed by the MDMCFG3.DRATE_M and the MDMCFG4.DRATE_E configuration registers. The data rate is given by the formula below. RDATA 256 DRATE _ M 2 DRATE _ E f 2 28 ref The following approach can be used to find suitable values for a given data rate: If DRATE_M is rounded to the nearest integer and becomes 256, increment DRATE_E and use DRATE_M=0. Note that the maximum data rate will be limited by the system clock speed. Please see 12.1.5.2 for more details. 13.6 Receiver Channel Filter Bandwidth In order to meet different channel width requirements, the receiver channel filter is programmable. The MDMCFG4.CHANBW_E and MDMCFG4.CHANBW_M configuration registers control the receiver channel filter bandwidth. The following formula gives the relation between the register settings and the channel filter bandwidth: BWchannel f ref 8 (4 CHANBW _ M )*2CHANBW _ E For best performance, the channel filter bandwidth should be selected so that the signal bandwidth occupies at most 80% of the channel filter bandwidth. The channel centre tolerance due to crystal accuracy should also be subtracted from the signal bandwidth. The following example illustrates this: With the channel filter bandwidth set to 500 kHz, the signal should stay within 80% of 500 kHz, which is 400 kHz. Assuming 915 MHz frequency and 20 ppm frequency uncertainty for both the transmitting device and the receiving device, the total frequency uncertainty is 40 ppm of 915 MHz, which is 37 kHz. If the whole transmitted signal bandwidth is to be received within 400 kHz, the transmitted signal bandwidth should be maximum 400 kHz - 2*37 kHz, which is 326 kHz. The CC1110Fx/CC1111Fx supports channel filter bandwidths shown in Table 62 and Table 63 respectively. SWRS033G Page 190 of 244 CC1110Fx / CC1111Fx MDMCFG4. MDMCFG4.CHANBW_E MDMCFG4. CHANBW_M 00 01 10 11 CHANBW_M 00 01 10 11 00 812 406 203 102 00 750 375 188 94 01 650 325 162 81 01 600 300 150 75 10 541 270 135 68 10 500 250 125 63 11 464 232 116 58 11 429 214 107 54 Table 62: Channel Filter Bandwidths [kHz] (assuming fref = 26 MHz) 13.7 Table 63: Channel Filter Bandwidths [kHz] (assuming fref = 24 MHz) Demodulator, Symbol Synchronizer, and Data Decision CC1110Fx/CC1111Fx contains an advanced and highly configurable demodulator. Channel filtering and frequency offset compensation is performed digitally. To generate the RSSI level (see Section 13.10.3 for more information) the signal level in the channel is estimated. Data filtering is also included for enhanced performance. 13.7.1 MDMCFG4.CHANBW_E Frequency Offset Compensation 13.7.2 The bit synchronization algorithm extracts the clock from the incoming symbols. The algorithm requires that the expected data rate is programmed as described in Section 13.5 on Page 190. Re-synchronization is performed continuously to adjust for error in the incoming symbol rate. 13.7.3 When using 2-FSK, GFSK, or MSK modulation, the demodulator will compensate for the offset between the transmitter and receiver frequency, within certain limits, by estimating the centre of the received data. This value is available in the FREQEST status register. Writing the value from FREQEST into FSCTRL0.FREQOFF the frequency synthesizer is automatically adjusted according to the estimated frequency offset. The tracking range of the algorithm is selectable as fractions of the channel bandwidth with the FOCCFG.FOC_LIMIT configuration register. If the FOCCFG.FOC_BS_CS_GATE bit is set, the offset compensator will freeze until carrier sense asserts. This may be useful when the radio is in RX for long periods with no traffic, since the algorithm may drift to the boundaries when trying to track noise. The tracking loop has two gain factors, which affects the settling time and noise sensitivity of the algorithm. FOCCFG.FOC_PRE_K sets the gain before the sync word is detected, and FOCCFG.FOC_POST_K selects the gain after the sync word has been found. Note that frequency offset compensation is not supported for ASK or OOK modulation. Bit Synchronization Byte Synchronization Byte synchronization is achieved by a continuous sync word search. The sync word is a 16 bit configurable field (can be repeated to get a 32 bit) that is automatically inserted at the start of the packet by the modulator in transmit mode. The demodulator uses this field to find the byte boundaries in the stream of bits. The sync word will also function as a system identifier since only packets with the correct predefined sync word will be received if the sync word detection in RX is enabled in register MDMCFG2 (see Section 13.10.1). The sync word detector correlates against the userconfigured 16 or 32 bit sync word. The correlation threshold can be set to 15/16, 16/16, or 30/32 bits match. The sync word can be further qualified using the preamble quality indicator mechanism described below and/or a carrier sense condition. The sync word is configured through the SYNC1 and SYNC0 registers and is sent MSB first. In order to make false detections of sync words less likely, a mechanism called preamble quality indication (PQI) can be used to qualify the sync word. A threshold value for the preamble quality must be exceeded in order for a detected sync word to be accepted. See Section 13.10.2 on Page 196 for more details. SWRS033G Page 191 of 244 CC1110Fx / CC1111Fx 13.8 Packet Handling Hardware Support The CC1110Fx/CC1111Fx has built-in hardware support for packet oriented radio protocols. Whitening of the data with a PN9 sequence. In transmit mode, the packet handler can be configured to add the following elements to the packet: Forward error correction by the use of interleaving and coding of the data (convolutional coding). A programmable number of preamble bytes In receive mode, the packet handling support will de-construct the data packet by implementing the following (if enabled): A two byte synchronization (sync) word. Can be duplicated to give a 4-byte sync word (recommended). It is not possible to only insert preamble or only insert a sync word. Preamble detection Sync word detection CRC computation and CRC check A CRC checksum computed over the data field One byte address check Packet length check (length byte checked against a programmable maximum length) The recommended setting is 4-byte preamble and 4-byte sync word, except for 500 kBaud data rate where the recommended preamble length is 8 bytes. In addition, the following can be implemented on the data field and the optional 2-byte CRC checksum: De-whitening De-interleaving and decoding Optionally, two status bytes (see Table 64 and Table 65) with RSSI value, Link Quality Indication, and CRC status can be appended to the received packet. Bit Field Name Description 7:0 RSSI RSSI value Table 64: Received Packet Status Byte 1 (first byte appended after the data) Bit Field name Description 7 CRC_OK 1: CRC for received data OK (or CRC disabled) 0: CRC error in received data 6:0 LQI The Link Quality Indicator estimates how easily a received signal can be demodulated Table 65: Received Packet Status Byte 2 (second byte appended after the data) Note that register fields that control the packet handling features should only be altered when CC1110Fx/CC1111Fx is in the IDLE state. 13.8.1 Data Whitening From a radio perspective, the ideal over the air data are random and DC free. This results in the smoothest power distribution over the occupied bandwidth. This also gives the regulation loops in the receiver uniform operation conditions (no data dependencies). Real world data often contain long sequences of zeros and ones. Performance can then be improved by whitening the data before transmitting, and de-whitening the data in the receiver. With CC1110Fx/CC1111Fx, this can be done automatically by setting PKTCTRL0.WHITE_DATA=1. All data, except the preamble and the sync word, are then XOR-ed with a 9-bit pseudo-random (PN9) SWRS033G Page 192 of 244 CC1110Fx / CC1111Fx sequence before being transmitted as shown in Figure 50. At the receiver end, the data are XOR-ed with the same pseudo-random sequence. This way, the whitening is reversed, and the original data appear in the receiver. The PN9 sequence is reset to all 1's. Data whitening can only be used when PKTCTRL0.CC2400_EN=0 (default). Figure 50: Data Whitening in TX Mode 13.8.2 Packet Format The format of the data packet can be configured and consists of the following items: Length byte or constant programmable packet length Optional Address byte Preamble Payload Synchronization word Optional 2 byte CRC Data field 16/32 bits 8 bits 8 bits 8 x n bits Legend: Inserted automatically in TX, processed and removed in RX. CRC-16 Address field 8 x n bits Length field Preamble bits (1010...1010) Sync word Optional data whitening Optionally FEC encoded/decoded Optional CRC-16 calculation Optional user-provided fields processed in TX, processed but not removed in RX. Unprocessed user data (apart from FEC and/or whitening) 16 bits Figure 51: Packet Format SWRS033G Page 193 of 244 CC1110Fx / CC1111Fx The preamble pattern is an alternating sequence of ones and zeros (101010101...). The minimum length of the preamble is programmable through the NUM_PREAMBLE field in the MDMCFG1 register. When enabling TX, the modulator will start transmitting the preamble. When the programmed number of preamble bytes have been transmitted, the modulator will send the sync word, and then data from the RFD register. If no data has been written to the RFD register when the radio is done transmitting the programmed number of preamble bytes, the modulator will continue to send preamble bytes until the first byte is written to RFD. It will then send the sync word followed by the data written to RFD. The sync. word is a two-byte value set in the SYNC1 and SYNC0 registers. The sync word provides byte synchronization of the incoming packet. A one-byte sync word can be emulated by setting the SYNC1 value to the preamble pattern. It is also possible to emulate a 32 bit sync word by using MDMCFG2.SYNC_MODE set to 3 or 7. The sync word will then be repeated twice. CC1110Fx/CC1111Fx supports both fixed packet length protocols and variable packet length protocols. Variable or fixed packet length mode can be used for packets up to 255 bytes. Fixed packet length mode is selected by setting PKTCTRL0.LENGTH_CONFIG=0. The desired packet length is set by the PKTLEN register. In variable packet length mode, PKTCTRL0.LENGTH_CONFIG=1, the packet length is configured by the first byte after the sync word. The packet length is defined as the payload data, excluding the length byte and the optional CRC. The PKTLEN register is used to set the maximum packet length allowed in RX. Any packet received with a length byte with a value greater than PKTLEN will be discarded. 13.8.3 Packet Filtering in Receive Mode CC2500 supports two different types of packetfiltering: address filtering and maximum length filtering. 13.8.3.1 Address Filtering Setting PKTCTRL1.ADR_CHK to any other value than zero enables the packet address filter. The packet handler engine will compare the destination address byte in the packet with the programmed node address in the ADDR register and the 0x00 broadcast address when PKTCTRL1.ADR_CHK=10 or both 0x00 and 0xFF broadcast addresses when PKTCTRL1.ADR_CHK=11. If the received address matches a valid address, the packet is accepted and the RFTXRXIF flag is asserted and a DMA trigger is generated. If the address match fails, the packet is discarded and receive mode restarted (regardless of the MCSM1.RXOFF_MODE setting). The RFIF.IRQ_DONE flag will be asserted but the DMA will not be triggered. 13.8.3.2 Maximum Length Filtering In variable packet length mode, PKTCTRL0.LENGTH_CONFIG=1, the PKTLEN.PACKET_LENGTH register value is used to set the maximum allowed packet length. If the received length byte has a larger value than this, the packet is discarded and receive mode restarted (regardless of the MCSM1.RXOFF_MODE setting). The RFIF.IRQ_DONE flag will be asserted but the DMA will not be triggered. 13.8.4 Packet Handling in Transmit Mode The payload that is to be transmitted must be written into RFD. The first byte written must be the length byte when variable packet length is enabled. The length byte has a value equal to the payload of the packet (including the optional address byte). If fixed packet length is enabled, then the first byte written to RFD is interpreted as the destination address, if this feature is enabled in the device that receives the packet. The modulator will first send the programmed number of preamble bytes. If data has been written to RFD, the modulator will send the twobyte (optionally 4-byte) sync word and then the content of the RFD register. If CRC is enabled, the checksum is calculated over all the data pulled from the RFD register and the result is sent as two extra bytes following the payload data. If fewer bytes are written to the RFD registers than what the radio expects the radio will enter TX_UNDERFLOW state and the RFIF.IRQ_TXUNF flag will be set together with RFIF.IRQ_DONE. An SIDLE strobe needs to be issued to return to IDLE state. If whitening is enabled, everything following the sync words will be whitened. This is done before the optional FEC/Interleaver stage. Whitening is enabled by setting PKTCTRL0.WHITE_DATA=1. SWRS033G Page 194 of 244 CC1110Fx / CC1111Fx If FEC/Interleaving is enabled, everything following the sync words will be scrambled by the interleaver and FEC encoded before being modulated. FEC is enabled by setting MDMCFG1.FEC_EN=1. 13.8.5 Packet Handling in Receive Mode In receive mode, the demodulator and packet handler will search for a valid preamble and the sync word. When found, the demodulator has obtained both bit and byte synchronism and will receive the first payload byte. If FEC/Interleaving is enabled, the FEC decoder will start to decode the first payload byte. The interleaver will de-scramble the bits before any other processing is done to the data. If whitening is enabled, the data will be dewhitened at this stage. and receives the number of bytes indicated by the length byte. If fixed packet length mode is used, the packet handler will accept the programmed number of bytes. Next, the packet handler optionally checks the address and only continues the reception if the address matches. If automatic CRC check is enabled, the packet handler computes CRC and matches it with the appended CRC checksum. At the end of the payload, the packet handler will optionally write two extra packet status bytes that contain CRC status, link quality indication and RSSI value. If a byte is received in the RFD register, and it is not read before the next byte is received, the radio will enter RX_OVERFLOW state and the RFIF.IRQ_RXOVF flag will be set together with RFIF.IRQ_DONE. An SIDLE strobe needs to be issued to return to IDLE state. When variable packet length mode is enabled, the first byte is the length byte. The packet handler stores this value as the packet length 13.9 Modulation Formats CC1110Fx/CC1111Fx supports frequency and phase shift modulation formats. The desired modulation format is set in the MDMCFG2.MOD_FORMAT register. Optionally, the data stream can be Manchester coded by the modulator and decoded by the demodulator. This option is enabled by setting MDMCFG2.MANCHESTER_EN=1. Note: Manchester encoding is not supported at the same time as using the FEC/Interleaver option or when using MSK modulation. 13.9.1 When FSK/GFSK modulation is used the DEVIATN register specifies the expected frequency deviation of incoming signal in RX and should be the same as the TX deviation for demodulation to be performed reliably and robustly. The frequency deviation is programmed with the DEVIATION_M and DEVIATION_E values in the DEVIATN register. The value has an exponent/mantissa form, and the resultant deviation is given by: f dev f ref 217 (8 DEVIATION _ M ) 2 DEVIATION _ E The symbol encoding is shown in Table 66. Frequency Shift Keying 2-FSK can optionally be shaped by a Gaussian filter with BT=1, producing a GFSK modulated signal. Format Symbol Coding 2-FSK/GFSK `0' -Deviation `1' +Deviation Table 66: Symbol Encoding for 2-FSK/GFSK Modulation SWRS033G Page 195 of 244 CC1110Fx / CC1111Fx 13.9.2 Minimum Shift Keying 13.9.3 21 Amplitude Modulation When using MSK , the complete transmission (preamble, sync word, and payload) will be MSK modulated. CC1110Fx/CC1111Fx supports two different forms of amplitude modulation: On-Off Keying (OOK) and Amplitude Shift Keying (ASK). Phase shifts are performed with a constant transition time. OOK modulation simply turns on or off the PA to modulate 1 and 0 respectively. The fraction of a symbol period used to change the phase can be modified with the DEVIATN.DEVIATION_M setting. This is equivalent to changing the shaping of the symbol. The ASK variant supported by the CC1110Fx/CC1111Fx allows programming of the modulation depth (the difference between 1 and 0), and shaping of the pulse amplitude. Pulse shaping will produce a more bandwidth constrained output spectrum. The MSK modulation format implemented in CC1110Fx/CC1111Fx inverts the sync word and data compared to e.g. signal generators. Note: The DEVIATN register setting has no effect in either RX or TX when using OOK/ASK. Note: The DEVIATN register setting has no effect in RX when using MSK. Also, when using MSK Manchester encoding/decoding should be disabled (MDMCFG2.MANCHESTER_EN=0) 21 Identical to offset QPSK with half-sine shaping (data coding may differ) 13.10 Received Signal Qualifiers and Link Quality Information CC1110Fx/CC1111Fx has several qualifiers that can be used to increase the likelihood that a valid sync word is detected. MDMCFG2. Sync Word Qualifier Mode SYNC_MODE 13.10.1 Sync Word Qualifier If sync word detection in RX is enabled in register MDMCFG2 the CC1110Fx/CC1111Fx will not start writing received data to the RFD register and perform the packet filtering described in Section 13.8.3 before a valid sync word has been detected. The sync word qualifier mode is set by MDMCFG2.SYNC_MODE and is summarized in Table 67. Carrier sense in Table 67 is described in Section 13.10.4. 000 No preamble/sync 001 15/16 sync word bits detected 010 16/16 sync word bits detected 011 30/32 sync word bits detected 100 No preamble/sync, carrier sense above threshold 101 15/16 + carrier sense above threshold 110 16/16 + carrier sense above threshold 111 30/32 + carrier sense above threshold Table 67: Sync Word Qualifier mode 13.10.2 Preamble Quality Threshold (PQT) The Preamble Quality Threshold (PQT) syncword qualifier adds the requirement that the received sync word must be preceded with a preamble with a quality above a programmed threshold. Another use of the preamble quality threshold is as a qualifier for the optional RX termination SWRS033G Page 196 of 244 CC1110Fx / CC1111Fx timer. See Section 13.12.3 on Page 204 for details. The preamble quality estimator increases an internal counter by one each time a bit is received that is different from the previous bit, and decreases the counter by 8 each time a bit is received that is the same as the last bit. The threshold is configured with the register field PKTCTRL1.PQT. A threshold of 4PQT for this counter is used to gate sync word detection. By setting the value to zero, the preamble quality qualifier of the sync word is disabled. A "Preamble Quality Reached" signal can be observed on P1_5, P1_6, or P1_7 by setting IOCFGx.GDOx_CFG=1000. It is also possible to determine if preamble quality is reached by checking the PQT_REACHED bit in the PKTSTATUS register. This signal / bit asserts when the received signal exceeds the PQT. The RSSI value is in dBm with 1/2 dB resolution. The RSSI update rate, fRSSI, depends on the receiver filter bandwidth (BW channel defined in Section 13.6) and AGCCTRL0.FILTER_LENGTH. f RSSI 2 BWchannel 8 2 FILTER _ LENGTH If PKTCTRL1.APPEND_STATUS is enabled the RSSI value at sync word detection is automatically added to the first byte appended after the data payload. The RSSI value read from the RSSI status register is a 2's complement number. The following procedure can be used to convert the RSSI reading to an absolute power level (RSSI_dBm). 1) Read the RSSI status register 2) Convert the reading from a hexadecimal number to a decimal number (RSSI_dec) 13.10.3 RSSI The RSSI value is an estimate of the signal level in the chosen channel. This value is based on the current gain setting in the RX chain and the measured signal level in the channel. In RX mode, the RSSI value can be read continuously from the RSSI status register until the demodulator detects a sync word (when sync word detection is enabled). At that point the RSSI readout value is frozen until the next time the chip enters the RX state. 3) If RSSI_dec 128 then RSSI_dBm = (RSSI_dec - 256)/2 - RSSI_offset 4) Else if RSSI_dec < 128 then RSSI_dBm = (RSSI_dec)/2 - RSSI_offset Table 68 provides typical values for the RSSI_offset. Figure 52 and Figure 53 shows typical plots of RSSI readings as a function of input power level for different data rates. Note: It takes some time from the radio enters RX mode until a valid RSSI value is present in the RSSI register. Please see DN505 [16] for details on how the RSSI response time can be estimated. Data rate [kBaud] RSSI_offset [dB], 315 MHz RSSI_offset [dB], 433 MHz RSSI_offset [dB], 868 MHz 1.2 74 75 73 38.4 73 74 73 250 74 73 77 Table 68: Typical RSSI_offset Values Figure 52 and Figure 53 show typical plots of RSSI readings as a function of input power level for different data rates. SWRS033G Page 197 of 244 CC1110Fx / CC1111Fx 0 -10 -20 -30 RSSI Readout [dBm] -40 -50 -60 -70 -80 -90 -100 -110 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 Input Power [dBm] 1.2 kBaud 38.4 kBaud 250 kBaud Figure 52: Typical RSSI Value vs. Input Power Level for Different Data Rates at 433 MHz 0 -10 -20 RSSI Readout [dBm] -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -120 -110 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 Input Power [dBm] 1.2 kBaud 38.4 kBaud 250 kBaud Figure 53: Typical RSSI Value vs. Input Power Level for Different Data Rates at 868 MHz 13.10.4 Carrier Sense (CS) The Carrier Sense (CS) flag is used as a sync word qualifier and for CCA. The CS flag can be set based on two conditions, which can be individually adjusted: CS is asserted when the RSSI is above a programmable absolute threshold, and de-asserted when RSSI is below the same threshold (with hysteresis). SWRS033G CS is asserted when the RSSI has increased with a programmable number of dB from one RSSI sample to the next, and de-asserted when RSSI has decreased with the same number of dB. This setting is not dependent on the absolute signal level and is thus useful to detect signals in environments with a time varying noise floor. Page 198 of 244 CC1110Fx / CC1111Fx Carrier Sense can be used as a sync word qualifier that requires the signal level to be higher than the threshold for a sync word search to be performed. The signal can also be observed on P1_5, P1_6, or P1_7 by setting IOCFGx.GDOx_CFG=1110 and in the status register bit PKTSTATUS.CS. MAX_LNA_GAIN[2:0] MAX_DVGA_GAIN[1:0] Other uses of Carrier Sense include the TX-ifCCA function (see Section 13.10.7 on Page 200) and the optional fast RX termination (see Section 13.12.3 on Page 204). CS can be used to avoid interference from other RF sources in the ISM bands. The absolute threshold related to the RSSI value depends on the following register fields: AGCCTRL2.MAX_DVGA_GAIN AGCCTRL1.CARRIER_SENSE_ABS_THR AGCCTRL2.MAGN_TARGET For a given AGCCTRL2.MAX_LNA_GAIN and AGCCTRL2.MAX_DVGA_GAIN setting the absolute threshold can be adjusted 7 dB in steps of 1 dB using CARRIER_SENSE_ABS_THR. The MAGN_TARGET setting is a compromise between blocker tolerance/selectivity and sensitivity. The value sets the desired signal level in the channel into the demodulator. Increasing this value reduces the headroom for blockers, and therefore close-in selectivity. It is (R) strongly recommended to use SmartRF Studio [9] to generate the correct MAGN_TARGET setting. Table 69 and Table 70 show the typical RSSI readout values at the CS threshold at 2.4 kBaud and 250 kBaud data rate respectively. The default CARRIER_SENSE_ABS_THR=0 (0 dB) and MAGN_TARGET=11 (33 dB) have been used. For other data rates the user must generate similar tables to find the CS absolute threshold. 10 11 000 -99 -93 -87 -81.5 001 -97 -90.5 -85 -78.5 010 -93.5 -87 -82 -76 011 -91.5 -86 -80 -74 100 -90.5 -84 -78 -72.5 101 -88 -82.5 -76 -70 110 -84.5 -78.5 -73 -67 111 -82.5 -76 -70 -64 MAX_DVGA_GAIN[1:0] MAX_LNA_GAIN[2:0] AGCCTRL2.MAX_LNA_GAIN 01 Table 69: Typical RSSI Value in dBm at CS Threshold with Default MAGN_TARGET at 2.4 kBaud 13.10.5 CS Absolute Threshold 00 00 01 10 11 000 -96 -90 -84 -78.5 001 -94.5 -89 -83 -77.5 010 -92.5 -87 -81 -75 011 -91 -85 -78.5 -73 100 -87.5 -82 -76 -70 101 -85 -79.5 -73.5 -67.5 110 -83 -76.5 -70.5 -65 111 -78 -72 -66 -60 Table 70: Typical RSSI Value in dBm at CS Threshold with Default MAGN_TARGET at 250 kBaud If the threshold is set high, i.e. only strong signals are wanted, the threshold should be adjusted upwards by first reducing the MAX_LNA_GAIN value and then the MAX_DVGA_GAIN value. This will reduce power consumption in the receiver front end, since the highest gain settings are avoided. 13.10.6 CS Relative Threshold The relative threshold detects sudden changes in the measured signal level. This setting is not dependent on the absolute signal level and is thus useful to detect signals in environments with a time varying noise floor. The register field AGCCTRL1.CARRIER_SENSE_REL_THR is used to enable/disable relative CS, and to select threshold of 6 dB, 10 dB or 14 dB RSSI change SWRS033G Page 199 of 244 CC1110Fx / CC1111Fx Always (CCA disabled, always goes to TX) 13.10.7 Clear Channel Assessment (CCA) The Clear Channel Assessment CCA) is used to indicate if the current channel is free or busy. The current CCA state is viewable on P1_5, P1_6, or P1_7 by setting IOCFGx.GDOx_CFG=1001. If RSSI is below threshold Unless currently receiving a packet Both the above (RSSI below threshold and not currently receiving a packet) MCSM1.CCA_MODE selects the mode to use when determining CCA. When the STX or SFSTXON command strobe is given while CC1110Fx/CC1111Fx is in the RX state, the TX or FSTXON state is only entered if the clear channel requirements are fulfilled. The chip will otherwise remain in RX (if the channel becomes available, the radio will not enter TX or FSTXON state before a new strobe command is being issued). This feature is called TX-if-CCA. Note that when using this function the register TEST1 on Page 225 should be set to 0x31. Four CCA requirements can be programmed: 13.10.8 Link Quality Indicator (LQI) The Link Quality Indicator is a metric of the current quality of the received signal. If PKTCTRL1.APPEND_STATUS is enabled, the value is automatically added to the last byte appended after the payload. The value can also be read from the LQI status register. The LQI gives an estimate of how easily a received signal can be demodulated by accumulating the magnitude of the error between ideal constellations and the received signal over the 64 symbols immediately following the sync word. LQI is best used as a relative measurement of the link quality (a high value indicates a better link than what a low value does), since the value is dependent on the modulation format. 13.11 Forward Error Correction with Interleaving 13.11.1 Forward Error Correction (FEC) CC1110Fx/CC1111Fx has built in support for Forward Error Correction (FEC). To enable this option, set MDMCFG1.FEC_EN to 1. FEC is only supported in fixed packet length mode (PKTCTRL0.LENGTH_CONFIG=0). FEC is employed on the data field and CRC word in order to reduce the gross bit error rate when operating near the sensitivity limit. Redundancy is added to the transmitted data in such a way that the receiver can restore the original data in the presence of some bit errors. The use of FEC allows correct reception at a lower SNR, thus extending communication range. Alternatively, for a given SNR, using FEC decreases the bit error rate (BER). As the packet error rate (PER) is related to BER by: PER 1 (1 BER) packet _ length , a lower BER can be used to allow longer packets, or a higher percentage of packets of a given length, to be transmitted successfully. Finally, in realistic ISM radio environments, transient and time-varying phenomena will produce occasional errors even in otherwise good reception conditions. FEC will mask such errors and, combined with interleaving of the coded data, even correct relatively long periods of faulty reception (burst errors). The FEC scheme adopted for CC1110Fx/CC1111Fx is convolutional coding, in which n bits are generated based on k input bits and the m most recent input bits, forming a code stream able to withstand a certain number of bit errors between each coding state (the m-bit window). The convolutional coder is a rate 1/2 code with a constraint length of m=4. The coder codes one input bit and produces two output bits; hence, the effective data rate is halved. I.e. to transmit at the same effective data rate when using FEC, it is necessary to use twice as high over-the-air data rate. This will require a higher receiver bandwidth, and thus reduce sensitivity. In other words, the improved reception by using FEC and the degraded sensitivity from a higher receiver bandwidth will be counteracting factors. 13.11.2 Interleaving Data received through radio channels will often experience burst errors due to interference and time-varying signal strengths. In order to increase the robustness to errors spanning SWRS033G Page 200 of 244 CC1110Fx / CC1111Fx multiple bits, interleaving is used when FEC is enabled. After de-interleaving, a continuous span of errors in the received stream will become single errors spread apart. control hardware therefore automatically inserts one or two extra bytes at the end of the packet, so that the total length of the data to be interleaved is an even number. Note that these extra bytes are invisible to the user, as they are removed before the received packet enters the RFD data register. CC1110Fx/CC1111Fx employs matrix interleaving, which is illustrated in Figure 54. The on-chip interleaving and de-interleaving buffers are 4 x 4 matrices. In the transmitter, the data bits from the rate 1/2 convolutional coder are written into the rows of the matrix, whereas the bit sequence to be transmitted is read from the columns of the matrix. In the receiver, the received symbols are written into the rows of the matrix, whereas the data passed onto the convolutional decoder is read from the columns of the matrix. When FEC and interleaving is used the minimum data payload is 2 bytes. Note: When using FEC (MDMCFG1.FEC_EN=1), CLKCON.CLKSPD must be set to 000. When FEC and interleaving is used at least one extra byte is required for trellis termination. In addition, the amount of data transmitted over the air must be a multiple of the size of the interleaver buffer (two bytes). The packet Interleaver Write buffer Packet Engine Interleaver Read buffer FEC Encoder Modulator Interleaver Write buffer Interleaver Read buffer FEC Decoder Demodulator Packet Engine Figure 54: General Principle of Matrix Interleaving 13.12 Radio Control CC1110Fx/CC1111Fx has a built-in state machine that is used to switch between different operation states (modes). The change of state is done either by using command strobes or by internal events such as TX FIFO underflow. Figure 48 on Page 186. The complete radio control state diagram is shown in Figure 55. The numbers refer to the state number readable in the MARCSTATE status register. This register is primarily for test purposes. A simplified state diagram, together with typical usage and current consumption, is shown in SWRS033G Page 201 of 244 CC1110Fx / CC1111Fx Figure 55: Complete Radio Control State Diagram SWRS033G Page 202 of 244 CC1110Fx / CC1111Fx 13.12.1 Active Modes The radio has two active modes: receive and transmit. These modes are activated directly by writing the SRX and STX command strobes to the RFST register. The frequency synthesizer must be calibrated regularly. CC1110Fx/CC1111Fx has one manual calibration option (using the SCAL strobe), and three automatic calibration options, controlled by the MCSM0.FS_AUTOCAL setting: Calibrate when going from IDLE to either RX or TX (or FSTXON) Calibrate when going from either RX or TX to IDLE automatically Calibrate every fourth time when going from either RX or TX to IDLE automatically If the radio goes from TX or RX to IDLE by issuing an SIDLE strobe, calibration will not be performed. The calibration takes a constant number of XOSC cycles (see Table 71 for timing details regarding calibration. When RX is activated, the chip will remain in receive mode until a packet is successfully received or the RX termination timer expires (see Section 13.12.3). Note: the probability that a false sync word is detected can be reduced by using PQT, CS, maximum sync word length, and sync word qualifier mode as describe in Section 13.10.1. After a packet is successfully received the radio controller will then go to the state indicated by the MCSM1.RXOFF_MODE setting. The possible destinations are: IDLE FSTXON: Frequency synthesizer on and ready at the TX frequency. Activate TX with STX. TX: Start sending preambles RX: Start search for a new packet Note: When MCSM1.RXOFF_MODE=11 and a packet has been received, it will take some time before a valid RSSI value is present in the RSSI register again even if the radio has never exited RX mode. This time is the same as the RSSI response time discussed in DN505 [16]. Similarly, when TX is active the chip will remain in the TX state until the current packet has been successfully transmitted. Then the state will change as indicated by the MCSM1.TXOFF_MODE setting. The possible destinations are the same as for RX. It is possible to change the state from RX to TX and vice versa by using the command strobes. If the radio controller is currently in transmit and an SRX strobe is written to the RFST register, the current transmission will be ended and the transition to RX will be done. If the radio controller is in RX when the STX or SFSTXON command strobes are used and MCSM1.CCA_MODE00, the TX-if-CCA function will be used. Note that for TX-if-CCA function the register TEST1 on Page 225 TEST1 should be set to 0x31. If the channel is not clear, the chip will remain in RX. For more details on clear channel assessment see Section 13.10.7 on Page 200 for details. The SIDLE command strobe can always be used to force the radio controller to go to the IDLE state. 13.12.2 Timing The radio controller controls most timing in CC1110Fx/CC1111Fx, such as synthesizer calibration, PLL lock time, and RX/TX turnaround times. Table 71 shows the timing for key state transitions when the system clock frequency fSys is equal to fRef and the data rate is 250 kBaud. No PA ramping/shaping is implemented. See DN110 [15] for more details on how the state transition times changes under other conditions. Power on time and XOSC start-up times are variable, but within the limits stated in Table 11 and Table 12 Note that in a frequency hopping spread spectrum or a multi-channel protocol it is possible to reduce the calibration time significantly. This is explained in Section 13.18.2. SWRS033G Page 203 of 244 CC1110Fx / CC1111Fx Transmission Time as a function of fRef and/or fSymbol22 Description Transition Time [s] fRef = 26 MHz fRef = 24 MHz 1953/fSys 75.1 81.4 20768/fSys 799 865 1954/fSys 75.2 81.4 20768/fSys 799 865 TX to RX switch 782/fSys + 0.25/fSymbol 31.1 33.6 RX to TX switch 782/fSys 30.1 32.6 ~0.25/fSymbol ~1 ~1 ~0.25/fSymbol +18815/fSys 725 785 2/fSys 0.1 0.1 18817/fSys 724 784 19098/fSys 735 796 Idle to RX, no calibration 23 Idle to RX, with calibration Idle to TX/FSTXON, no calibration Idle to TX/FSTXON, with calibration TX to IDLE, no calibration TX to IDLE, with calibration 23 RX to IDLE, no calibration RX to IDLE, with calibration 23 Manual calibration 23 Table 71: State Transition Timing 13.12.3 RX Termination Timer CC1110Fx/CC1111Fx has optional functions for automatic termination of RX after a programmable time. The termination timer starts when in RX state. The timeout is programmable with the MCSM2.RX_TIME setting. When the timer expires, the radio controller will check the condition for staying in RX; if the condition is not met, RX will terminate. The programmable conditions are: MCSM2.RX_TIME_QUAL=0: Continue receive if sync word has been found MCSM2.RX_TIME_QUAL=1: Continue receive if sync word has been found or preamble quality is above threshold (PQT) If the system can expect the transmission to have started when enabling the receiver, the MCSM2.RX_TIME_RSSI function can be used. The radio controller will then terminate RX if the first valid carrier sense sample indicates no carrier (RSSI below threshold). See Section 13.10.4 on Page 198 for details on Carrier Sense. For ASK/OOK modulation, lack of carrier sense is only considered valid after eight symbol periods. Thus, the MCSM2.RX_TIME_RSSI function can be used in ASK/OOK mode when the distance between "1" symbols is 8 or less. If RX terminates due to no carrier sense when the MCSM2.RX_TIME_RSSI function is used, or if no sync word was found when using the MCSM2.RX_TIME timeout function, the chip will always go back to IDLE. 13.13 Frequency Programming The frequency programming in CC1110Fx/CC1111Fx is designed to minimize the programming needed in a channel-oriented system. To set up a system with channel numbers, the desired channel spacing is programmed with the MDMCFG0.CHANSPC_M and MDMCFG1.CHANSPC_E registers. The channel spacing registers are mantissa and exponent respectively. The base or start frequency is set by the 24 bit frequency word located in the FREQ2, FREQ1 and FREQ0 registers. This word will typically be 22 fSymbol is the symbol rate for the data transmission (in this case 250 kBaud). Please see DN110 [15] for more details 23 This is the calibration time given that TEST0=0x0B and FSCAL3.CHP_CURR_CAL_EN=10 (max calibration time). Please see DN110 [15] for more details SWRS033G Page 204 of 244 CC1110Fx / CC1111Fx set to the centre of the lowest channel frequency that is to be used. CHANNR.CHAN, which is multiplied by the channel offset. The resultant carrier frequency is given by: The desired channel number is programmed with the 8-bit channel number register, f carrier f ref 216 FREQ CHAN ( 256 CHANSPC _ M ) 2 CHANSPC _ E 2 With a reference frequency, fRef, equal to 26 MHz, the maximum channel spacing is 405 kHz. To get e.g. 1 MHz channel spacing one solution is to use 333 kHz channel spacing and select each third channel in CHANNR.CHAN. The preferred IF frequency is programmed with the FSCTRL1.FREQ_IF register. The IF frequency is given by: f IF f ref 210 FREQ _ IF (R) Note that the SmartRF Studio software [9] automatically calculates the optimum register setting based on channel spacing and channel filter bandwidth. If any frequency programming register is altered when the frequency synthesizer is running, the synthesizer may give an undesired response. Hence, the frequency programming should only be updated when the radio is in the IDLE state. 13.14 VCO The VCO is completely integrated on-chip. 13.14.1 VCO and PLL Self-Calibration The VCO characteristics will vary with temperature and supply voltage changes, as well as the desired operating frequency. In order to ensure reliable operation, CC1110Fx/CC1111Fx includes frequency synthesizer self-calibration circuitry. This calibration should be done regularly, and must be performed after turning on power and before using a new frequency (or channel). The number of fRef periods for completing the PLL calibration is given in Table 71 on Page 204. The calibration can be initiated automatically or manually. The synthesizer can be automatically calibrated each time the synthesizer is turned on, or each time the synthesizer is turned off automatically. This is configured with the MCSM0.FS_AUTOCAL register setting. In manual mode, the calibration is initiated when the SCAL command strobe is activated in the IDLE mode. Note that the calibration values are maintained in power-down modes PM1/2/3, so the calibration is still valid after waking up from these power-down modes (unless supply voltage or temperature has changed significantly). 13.15 Output Power Programming The RF output power level from the device has two levels of programmability, as illustrated in Figure 56. Firstly, the PA_TABLE7 PA_TABLE0 registers can hold up to eight user selected output power settings. Secondly, the 3-bit FREND0.PA_POWER value selects the PA_TABLE7 - PA_TABLE0 register to use. This two-level functionality provides flexible PA power ramp up and ramp down at the start and end of transmission, as well as ASK modulation shaping. All the PA power settings in the PA_TABLE7 - PA_TABLE0 registers, from index 0 up to the index set by FREND0.PA_POWER, values are used. The power ramping at the start and at the end of a packet can be turned off by setting FREND0.PA_POWER to zero and then program the desired output power to PA_TABLE0 register. If OOK modulation is used, the logic 0 and logic 1 power levels shall be programmed to index 0 and 1 respectively, i.e. PA_TABLE0 and PA_TABLE1. Table 72 contains recommended PA_TABLE settings for various output levels and frequency bands. Using PA settings from 0x68 to 0x6F is not recommended. SWRS033G Page 205 of 244 CC1110Fx / CC1111Fx 315 MHz 433 MHz 868 MHz 915 MHz Output Power [dBm] Setting Current Consumption, Typ. [mA] Setting Current Consumption, Typ. [mA] Setting Current Consumption, Typ. [mA] Setting Current Consumption, Typ. [mA] -30 0x12 14 0x12 15 0x03 16 0x03 16 -20 0x0D 15 0x0E 16 0x0E 17 0x0D 16 -15 0x1C 16 0x1D 16 0x1E 17 0x1D 17 -10 0x34 17 0x34 18 0x27 19 0x26 18 -5 0x2B 19 0x2C 20 0x8F 19 0x57 18 0 0x51 19 0x60 20 0x50 21 0x8E 21 5 0x85 22 0x84 23 0x84 25 0x83 25 7 0xCB 25 0xC8 28 0xCB 31 0xC7 31 10 0xC2 31 0xC0 33 0xC2 36 0xC0 36 Table 72: Optimum PA_TABLE Settings for Various Output Power Levels and Frequency Bands 13.16 Shaping and PA Ramping With ASK modulation, up to eight power settings are used for shaping. The modulator contains a counter that counts up when transmitting a one and down when transmitting a zero. The counter counts at a rate equal to 8 times the symbol rate. The counter saturates at FREND0.PA_POWER and 0 respectively. This counter value can be viewed as an index for a lookup table in the power table (see Figure 56). Thus, in order to utilize the whole table, FREND0.PA_POWER should be 7 when ASK is active. The shaping of the ASK signal is dependent on the configuration of PA_TABLE7 - PA_TABLE0 registers. Figure 57 shows some examples of ASK shaping. PA_TABLE7[7:0] The PA uses this setting. PA_TABLE6[7:0] PA_TABLE5[7:0] PA_TABLE4[7:0] Settings 0 to PA_POWER are used during ramp-up at start of transmission and ramp-down at end of transmission, and for ASK/OOK modulation. PA_TABLE3[7:0] PA_TABLE2[7:0] PA_TABLE1[7:0] PA_TABLE0[7:0] Index into PA_TABLE The SmartRF(R) Studio software should be used to obtain optimum PA_TABLE settings for various output powers. e.g 6 PA_POWER[2:0] in FREND0 register Figure 56: PA_POWER and PA_TABLE Output Power PA_TABLE7 PA_TABLE6 PA_TABLE5 PA_TABLE4 PA_TABLE3 PA_TABLE2 PA_TABLE1 PA_TABLE0 1 0 0 1 0 1 1 0 Time Bit Sequence FREND0.PA_POWER = 3 FREND0.PA_POWER = 7 SWRS033G Page 206 of 244 CC1110Fx / CC1111Fx Figure 57: Shaping of ASK Signal 13.17 Selectivity Figure 58 to Figure 60 show the typical selectivity performance (adjacent and alternate rejection). 50.0 40.0 Selectivity [dB] 30.0 20.0 10.0 0.0 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 0.1 0.2 0.4 0.5 -10.0 -20.0 Frequency offset [MHz] Figure 58: Typical Selectivity at 1.2 kBaud @ 868 MHz. IF Frequency is 152 kHz. MDMCFG2.DEM_DCFILT_OFF=0 50.0 40.0 Selectivity [dB] 30.0 20.0 10.0 0.0 -1.0 -0.8 -0.5 -0.4 -0.3 -0.2 -0.1 0.0 0.1 0.2 0.4 0.5 0.8 1.0 -10.0 -20.0 Frequency offset [MHz] Figure 59: Typical Selectivity at 38.4 kBaud@ 868 MHz. IF Frequency is 152 kHz. MDMCFG2.DEM_DCFILT_OFF=0 SWRS033G Page 207 of 244 CC1110Fx / CC1111Fx 50.0 40.0 Selectivity [dB] 30.0 20.0 10.0 0.0 -3.00 -2.25 1.50 -1.00 -0.75 0.00 0.75 1.00 1.50 2.25 3.00 -10.0 -20.0 Frequency offset [MHz] Figure 60: Typical Selectivity at 250 kBaud @ 868 MHz. IF Frequency is 304 kHz. MDMCFG2.DEM_DCFILT_OFF=0 13.18 System Considerations and Guidelines 13.18.1 SRD/ISM Regulations International regulations and national laws regulate the use of radio receivers and transmitters. Short Range Devices (SRDs) for license free operation below 1 GHz are usually operated in the 315 MHz, 433 MHz, 868 MHz or 915 MHz frequency bands. The CC1110Fx/CC1111Fx is specifically designed for such use with its 300 - 348 MHz, 391 - 464 MHz, and 782 - 928 MHz operating ranges. The most important regulations when using the CC1110Fx/CC1111Fx in the 433 MHz, 868 MHz, or 915 MHz frequency bands are EN 300 220 (Europe) and FCC CFR47 part 15 (USA). A summary of the most important aspects of these regulations can be found in [10] or [11]. Please note that compliance with regulations is dependent on complete system performance. It is the customer's responsibility to ensure that the system complies with regulations. 13.18.2 Frequency Hopping Channel Systems and Multi- The 433 MHz, 868 MHz, or 915 MHz are shared by many systems both in industrial, office and home environments. It is therefore recommended to use frequency hopping spread spectrum (FHSS) or a multi-channel protocol because the frequency diversity makes the system more robust with respect to interference from other systems operating in the same frequency band. FHSS also combats multipath fading. Charge pump current, VCO current and VCO capacitance array calibration data is required for each frequency when implementing frequency hopping for CC1110Fx/CC1111Fx. There are 3 ways of obtaining the calibration data from the chip: 1) Frequency hopping with calibration for each hop. The PLL calibration time is approximately 24 735 s and the blanking interval between each frequency hop is then approximately 799 24 s when fRef is 26 MHz. When fRef is 24 MHz, 24 24 these numbers are 796 s and 865 s respectively. 2) Fast frequency hopping without calibration for each hop can be done by calibrating each frequency at startup and saving the resulting FSCAL3, FSCAL2 and FSCAL1 register values in memory. Between each frequency hop, the calibration process can then be replaced by writing the FSCAL3, FSCAL2 and FSCAL1 register values corresponding to the next RF frequency. The PLL turn on time is 24 approximately 75 s when fRef is 26 MHz and 24 81 s when fRef is 24 MHz. The blanking interval between each frequency hop is then approximately equal to the PLL turn on time. The VCO current calibration result is available in FSCAL2 and is not dependent on the RF frequency. Neither is the charge pump current calibration result available in FSCAL3. The same value can therefore be used for all frequencies. 24 The system clock frequency is equal to fRef and no PA ramping/shaping is implemented. Max calibration time is used (TEST0=0x0B and FSCAL3.CHP_CURR_CAL_EN=10) Please see DN110 [15] for more details. SWRS033G Page 208 of 244 CC1110Fx / CC1111Fx 3) Run calibration on a single frequency at startup. Next write 0 to FSCAL3[5:4] to disable the charge pump calibration. After writing to FSCAL3[5:4] strobe SRX (or STX) with MCSM0.FS_AUTOCAL=01 for each new frequency hop. That is, VCO current and VCO capacitance calibration is done but not charge pump current calibration. When charge pump current calibration is disabled the calibration 24 25 time is reduced from 735 s to 168 s 24 when fRef is 26 MHz and from 799 s to 182 25 s when fRef is 24 MHz. The blanking interval between each frequency hop is then 243 s and 263 s respectively. There is a trade off between blanking time and memory space needed for storing calibration data in non-volatile memory. Solution 2) above gives the shortest blanking interval, but requires more memory space to store calibration values. Solution 3) gives 631 s smaller blanking interval than solution 1 when fRef is 26 MHz and 683 s smaller blanking interval than solution 1 when fRef is 24 MHz). 13.18.3 Wideband Modulation Spread Spectrum not Using Digital modulation systems under FCC part 15.247 includes 2-FSK and GFSK modulation. A maximum peak output power of 1 W (30 dBm) is allowed if the 6 dB bandwidth of the modulated signal exceeds 500 kHz. In addition, the peak power spectral density conducted to the antenna shall not be greater than 8 dBm in any 3 kHz band. Pleas refer to DN006 [12] for further details concerning wideband modulation and CC1110Fx/CC1111Fx. Operating with high frequency separation, the CC1110Fx/CC1111Fx is suited for systems targeting compliance with digital modulation systems as defined by FCC part 15.247. An external power amplifier is needed to increase the output above 10 dBm. 13.18.4 Data Burst Transmissions The high maximum data rate of CC1110Fx/CC1111Fx opens up for burst transmissions. A low average data rate link (e.g. 10 kBaud), can be realized using a higher over-the-air data rate. Buffering the data and transmitting in bursts at high data rate (e.g. 500 kBaud) will reduce the time in active mode, and hence also reduce the average current consumption significantly. Reducing the time in active mode will reduce the likelihood of collisions with other systems in the same frequency range. Note that sensitivity and thus transmission range is reduced in high data rate bursts compared to lower data rates. 13.18.5 Crystal Drift Compensation The CC1110Fx/CC1111Fx has a very fine frequency resolution (see Table 16). This feature can be used to compensate for frequency offset and drift. The frequency offset between an `external' transmitter and the receiver is measured in the CC1110Fx/CC1111Fx and can be read back from the FREQEST status register as described in Section 13.7.1. The measured frequency offset can be used to calibrate the frequency using the `external' transmitter as the reference. That is, the received signal of the device will match the receiver's channel filter better. In the same way the centre frequency of the transmitted signal will match the `external' transmitter's signal. 13.18.6 Spectrum Efficient Modulation CC1110Fx/CC1111Fx also has the possibility to use Gaussian shaped 2-FSK (GFSK). This spectrum-shaping feature improves adjacent channel power (ACP) and occupied bandwidth. In `true' 2-FSK systems with abrupt frequency shifting, the spectrum is inherently broad. By making the frequency shift `softer', the spectrum can be made significantly narrower. Thus, higher data rates can be transmitted in the same bandwidth using GFSK. 13.18.7 Low Cost Systems A HC-49 type SMD crystal is used in the CC1110EM reference design [1]. Note that the crystal package strongly influences the price. In a size constrained PCB design a smaller, but more expensive, crystal may be used. 13.18.8 Battery Operated Systems In low power applications, PM2 or PM3 should be used when the CC1110Fx/CC1111Fx is not active. The Sleep Timer can be used in PM2. 25 TEST0=0x0B. Please see DN110 [15] for more details. SWRS033G Page 209 of 244 CC1110Fx / CC1111Fx 13.18.9 Increasing Output Power In some applications it may be necessary to extend the link range. Adding an external power amplifier is the most effective way of doing this. The power amplifier should be inserted between the antenna and the balun, and two T/R switches are needed to disconnect the PA in RX mode. See Figure 61. Antenna Filter PA CC1110Fx / Balun T/R switch CC1111Fx T/R switch Figure 61: Block Diagram of CC1110Fx/CC1111Fx Usage with External Power Amplifier SWRS033G Page 210 of 244 CC1110Fx / CC1111Fx 13.19 Radio Registers This section describes all RF registers used for control and status for the radio. 0xDF2F: IOCFG2 - Radio Test Signal Configuration (P1_7) Bit Field Name 7 Reset R/W Description - R0 Not used 6 GDO2_INV 0 R/W Invert output, i.e. select active low (1) / high (0) 5:0 GDO2_CFG[5:0] 000000 R/W Debug output on P1_7 pin. See Table 73 for a description of internal signals which can be output on this pin for debug purpose 0xDF30: IOCFG1 - Radio Test Signal Configuration (P1_6) Bit Field Name Reset R/W Description 7 GDO_DS 0 R/W Drive strength control for I/O pins in output mode. Selects output drive capability to account for low I/O supply voltage VDD on pin DVDD 6 5:0 GDO1_INV GDO1_CFG[5:0] 0 000000 R/W R/W 0 Minimum drive capability. VDD equal or greater than 2.6 V 1 Maximum drive capability. VDD less than 2.6 V Invert output 0 Active high 1 Active low Debug output on P1_6 pin. See Table 73 for a description of internal signals which can be output on this pin for debug purpose 0xDF31: IOCFG0 - Radio Test Signal Configuration (P1_5) Bit Field Name 7 Reset R/W Description - R0 Not used 6 GDO0_INV 0 R/W Invert output, i.e. select active low (1) / high (0) 5:0 GDO0_CFG[5:0] 000000 R/W Debug output on P1_5 pin. See Table 73 for a description of internal signals which can be output on this pin for debug purpose. 0xDF00: SYNC1 - Sync Word, High Byte Bit Field Name Reset R/W Description 7:0 SYNC[15:8] 0xD3 R/W 8 MSB of 16-bit sync word 0xDF01: SYNC0 - Sync Word, Low Byte Bit Field Name Reset R/W Description 7:0 SYNC[7:0] 0x91 R/W 8 LSB of 16-bit sync word 0xDF02: PKTLEN - Packet Length Bit Field Name Reset R/W Description 7:0 PACKET_LENGTH 0xFF R/W Indicates the packet length when fixed length packets are enabled. If variable length packets are used, this value indicates the maximum length packets allowed SWRS033G Page 211 of 244 CC1110Fx / CC1111Fx 0xDF03: PKTCTRL1 - Packet Automation Control Bit Field Name Reset R/W Description 7:5 PQT[2:0] 000 R/W Preamble quality estimator threshold. The preamble quality estimator increases an internal counter by one each time a bit is received that is different from the previous bit, and decreases the counter by 8 each time a bit is received that is the same as the last bit. A threshold of 4PQT for this counter is used to gate sync word detection. When PQT=0 a sync word is always accepted 4:3 - R0 Not used 2 APPEND_STATUS 1 R/W When enabled, two status bytes will be appended to the payload of the packet. The status bytes contain RSSI and LQI values, as well as the CRC OK flag 1:0 ADR_CHK[1:0] 00 R/W Controls address check configuration of received packages. 00 No address check 01 Address check, no broadcast 10 Address check, 0 (0x00) broadcast 11 Address check, 0 (0x00) and 255 (0xFF) broadcast 0xDF04: PKTCTRL0 - Packet Automation Control Bit Field Name 7 6 5:4 WHITE_DATA PKT_FORMAT[1:0] 3 2 1:0 CRC_EN LENGTH_CONFIG[1:0] Reset R/W Description - R0 Not used 1 R/W Whitening enable. Data whitening can only be used when PKTCTRL0.CC2400_EN=0 (default). 00 R/W 0 Disabled 1 Enabled Packet format of RX and TX data 00 Normal mode 01 Reserved 10 Random TX mode; sends random data using PN9 generator. Used for test. Works as normal mode, setting 00, in RX. 11 Reserved 0 R/W Reserved. Always write 0 1 R/W CRC calculation in TX and CRC check in RX enable 01 R/W 0 Disable 1 Enable Packet Length Configuration 00 Fixed packet length mode. Length configured in PKTLEN register 01 Variable packet length mode. Packet length configured by the first byte after sync word 10 Reserved 11 Reserved SWRS033G Page 212 of 244 CC1110Fx / CC1111Fx 0xDF05: ADDR - Device Address Bit Field Name Reset R/W Description 7:0 DEVICE_ADDR[7:0] 0x00 R/W Address used for packet filtration. Optional broadcast addresses are 0 (0x00) and 255 (0xFF). 0xDF06: CHANNR - Channel Number Bit Field Name Reset R/W Description 7:0 CHAN[7:0] 0x00 R/W The 8-bit unsigned channel number, which is multiplied by the channel spacing setting and added to the base frequency. 0xDF07: FSCTRL1 - Frequency Synthesizer Control Bit Reset R/W Description 7:6 - R0 Not used 5 0 R/W Reserved 01111 R/W The desired IF frequency to employ in RX. Subtracted from FS base frequency in RX and controls the digital complex mixer in the demodulator. 4:0 Field Name FREQ_IF[4:0] f IF f ref 210 FREQ _ IF The default value gives an IF frequency of 381 kHz when fRef = 26 MHz and 352 kHz when fRef = 24 MHz. 0xDF08: FSCTRL0 - Frequency Synthesizer Control Bit Field Name Reset R/W Description 7:0 FREQOFF[7:0] 0x00 R/W Frequency offset added to the base frequency before being used by the FS. (2's complement). Resolution is fRef /214 Range is 202 kHz to 209 kHz for CC1110Fx and 186 kHz for CC1111Fx 0xDF09: FREQ2 - Frequency Control Word, High Byte Bit Field Name Reset R/W Description 7:6 FREQ[23:22] 01 R FREQ[23:22] 5:0 FREQ[21:16] 011110 R/W FREQ[23:0] is the base frequency for the frequency synthesizer in increments of fRef /216. f carrier f ref 216 FREQ23 : 0 0xDF0A: FREQ1 - Frequency Control Word, Middle Byte Bit Field Name Reset R/W Description 7:0 FREQ[15:8] 11000100 R/W Ref. FREQ2 register 0xDF0B: FREQ0 - Frequency Control Word, Low Byte Bit Field Name Reset R/W Description 7:0 FREQ[7:0] 11101100 R/W Ref. FREQ2 register SWRS033G Page 213 of 244 CC1110Fx / CC1111Fx 0xDF0C: MDMCFG4 - Modem configuration Bit Field Name Reset R/W 7:6 CHANBW_E[1:0] 10 R/W 5:4 CHANBW_M[1:0] 00 R/W Description Sets the decimation ratio for the delta-sigma ADC input stream and thus the channel bandwidth. BWchannel f ref 8 (4 CHANBW _ M )*2 CHANBW _ E The default values give 203 kHz channel filter bandwidth when fRef = 26 MHz and 188 kHz when fRef = 24 MHz. 3:0 DRATE_E[3:0] 1100 R/W The exponent of the user specified symbol rate. 0xDF0D: MDMCFG3 - Modem Configuration Bit Field Name Reset R/W Description 7:0 DRATE_M[7:0] 0x22 R/W The mantissa of the user specified symbol rate. The symbol rate is configured using an unsigned, floating-point number with 9-bit mantissa and 4-bit exponent. The 9th bit is a hidden `1'. The resulting data rate is: RDATA 256 DRATE _ M 2 DRATE _ E f 2 28 ref The default values give a data rate of 115.051 kBaud when fRef = 26 MHz and 106.201 kHz when fRef = 24 MHz. SWRS033G Page 214 of 244 CC1110Fx / CC1111Fx 0xDF0E: MDMCFG2 - Modem Configuration Bit Field Name Reset R/W Description 7 DEM_DCFILT_OFF 0 R/W Disable digital DC blocking filter before demodulator. The recommended IF frequency changes when the DC blocking is disabled. Please use SmartRF Studio [9] to calculate correct register setting. 6:4 MOD_FORMAT[2:0] 000 R/W 0 Enable Better Sensitivity 1 Disable Current optimized. Only for data rates 100 kBaud The modulation format of the radio signal 000 2-FSK 001 GFSK 010 Reserved 011 ASK/OOK 100 Reserved 101 Reserved 110 Reserved 111 MSK Note that MSK is only supported for data rates above 26 kBaud and GFSK, ASK , and OOK is only supported for data rate up until 250 kBaud. MSK cannot be used if Manchester encoding/decoding is enabled. 3 MANCHESTER_EN 0 R/W Manchester encoding/decoding enable 0 Disable 1 Enable Note that Manchester encoding/decoding cannot be used at the same time as using the FEC/Interleaver option or when using MSK modulation. 2:0 SYNC_MODE[2:0] 010 R/W Sync-word qualifier mode. The values 000 and 100 disables preamble and sync word transmission in TX and preamble and sync word detection in RX. The values 001, 010, 101 and 110 enables 16-bit sync word transmission in TX and 16-bits sync word detection in RX. Only 15 of 16 bits need to match in RX when using setting 001 or 101. The values 011 and 111 enables repeated sync word transmission in TX and 32-bits sync word detection in RX (only 30 of 32 bits need to match). 000 No preamble/sync 001 15/16 sync word bits detected 010 16/16 sync word bits detected 011 30/32 sync word bits detected 100 No preamble/sync, carrier-sense above threshold 101 15/16 + carrier-sense above threshold 110 16/16 + carrier-sense above threshold 111 30/32 + carrier-sense above threshold SWRS033G Page 215 of 244 CC1110Fx / CC1111Fx 0xDF0F: MDMCFG1 - Modem Configuration Bit Field Name Reset R/W Description 7 FEC_EN 0 R/W Enable Forward Error Correction (FEC) with interleaving for packet payload. FEC is only supported for fixed packet length mode, i.e. PKTCTRL0.LENGTH_CONFIG=0 6:4 NUM_PREAMBLE[2:0] 3:2 1:0 CHANSPC_E[1:0] 010 R/W 0 Disable 1 Enable Sets the minimum number of preamble bytes to be transmitted 000 2 001 3 010 4 011 6 100 8 101 12 110 16 111 24 - R0 Not used 10 R/W 2 bit exponent of channel spacing 0xDF10: MDMCFG0 - Modem Configuration Bit Field Name Reset R/W Description 7:0 CHANSPC_M[7:0] 0xF8 R/W 8-bit mantissa of channel spacing (initial 1 assumed). The channel spacing is multiplied by the channel number CHAN and added to the base frequency. It is unsigned and has the format: f CHANNEL f ref 218 256 CHANSPC _ M 2 CHANSPC _ E The default values give 199.951 kHz channel spacing when fRef = 26 MHz and 184.570 kHz when fRef = 24 MHz. SWRS033G Page 216 of 244 CC1110Fx / CC1111Fx 0xDF11: DEVIATN - Modem Deviation Setting Bit Field Name 7 6:4 DEVIATION_E[2:0] 3 2:0 DEVIATION_M[2:0] Reset R/W Description - R0 Not used 100 R/W Deviation exponent - R0 Not used 111 R/W TX 2-FSK/ GFSK Specifies the nominal frequency deviation from the carrier frequency for a `0' (-DEVIATN) and a `1' (+DEVIATN) in a mantissa-exponent format. The resulting deviation is given by: f dev f ref 217 (8 DEVIATION _ M ) 2 DEVIATION _ E The default values give 47.607 kHz deviation when MHz and 43.945 kHz when fRef = 24 MHz. fRef = 26 MSK Specifies the fraction of a symbol period (1/8-8/8) during which a phase change occurs (`0': +90deg, `1': -90deg). Refer to the SmartRF Studio software [9] for correct DEVIATN setting when using MSK. ASK This settings has no effect RX 2-FSK/ GFSK Specifies the expected frequency deviation of incoming signal, must be approximately right for demodulation to be performed reliably and robustly MSK/ASK This settings has no effect 0xDF12: MCSM2 - Main Radio Control State Machine Configuration Bit Field Name 7:5 Reset R/W Description - R0 Not used 4 RX_TIME_RSSI 0 R/W Direct RX termination based on RSSI measurement (carrier sense). For ASK/OOK modulation, RX times out if there is no carrier sense in the first 8 symbol periods. 3 RX_TIME_QUAL 0 R/W When the RX_TIME timer expires the chip stays in RX mode if sync word is found when RX_TIME_QUAL=0, or either sync word is found or PQT is reached when RX_TIME_QUAL=1. 2:0 RX_TIME[2:0] 111 R/W Timeout for sync word search in RX. The timeout is relative to the programmed tEvent0. The RX timeout in s is given by EVENT0*C(RX_TIME, WOR_RES) *26/X, where C is given by the table below and X is the reference frequency (fRef) in MHz: RX_TIME[2:0] WOR_RES=0 WOR_RES=1 WOR_RES=2 WOR_RES=3 000 3.6058 18.0288 32.4519 46.8750 001 1.8029 9.0144 16.2260 23.4375 010 0.9014 4.5072 8.1130 11.7188 011 0.4507 2.2536 4.0565 5.8594 100 0.2254 1.1268 2.0282 2.9297 101 0.1127 0.5634 1.0141 1.4648 110 0.0563 0.2817 0.5071 0.7324 111 Until end of packet As an example, EVENT0 = 34666, WOR_RES = 0 and RX_TIME = 6 corresponds to 1.96 ms RX timeout SWRS033G Page 217 of 244 CC1110Fx / CC1111Fx 0xDF13: MCSM1 - Main Radio Control State Machine Configuration Bit Field Name 7:6 5:4 3:2 CCA_MODE[1:0] RXOFF_MODE[1:0] Reset R/W Description - R0 Not used 11 R/W Selects CCA_MODE; Reflected in CCA signal 00 R/W 00 Always 01 If RSSI below threshold 10 Unless currently receiving a packet 11 If RSSI below threshold unless currently receiving a packet Select what should happen (next state) when a packet has been received 00 IDLE 01 FSTXON 10 TX 11 Stay in RX It is not possible to set RXOFF_MODE to be TX or FSTXON and at the same time use CCA. 1:0 TXOFF_MODE[1:0] 00 R/W Select what should happen (next state) when a packet has been sent (TX) 00 IDLE 01 FSTXON 10 Stay in TX (start sending preamble) 11 RX 0xDF14: MCSM0 - Main Radio Control State Machine Configuration Bit Field Name 7:6 5:4 FS_AUTOCAL[1:0] Reset R/W Description - R0 Not used 00 R/W Select calibration mode (when to calibrate) 00 Never (manually calibrate using SCAL strobe) 01 When going from IDLE to RX or TX (or FSTXON) 10 When going from RX or TX back to IDLE automatically 11 Every 4th time when going from RX or TX to IDLE automatically 3 0 R/W Reserved. Refer to SmartRF Studio software [9] for settings. 2 1 R/W Reserved. Refer to SmartRF Studio software [9] for settings. 00 R/W Sets RX attenuation. Used in order to avoid saturation in RX when two or more chips are close (within ~3 m). 1:0 CLOSE_IN_RX[1:0] RX attenuation, typical values: 00 0 dB 01 6 dB 10 12 dB 11 18 dB SWRS033G Page 218 of 244 CC1110Fx / CC1111Fx 0xDF15: FOCCFG - Frequency Offset Compensation Configuration Bit Field Name Reset R/W Description 7 - R0 Not used 6 1 R/W Reserved. Always write 0 5 FOC_BS_CS_GATE 1 R/W If set, the demodulator freezes the frequency offset compensation and clock recovery feedback loops until the CARRIER_SENSE signal goes high. 4:3 FOC_PRE_K[1:0] 10 R/W The frequency compensation loop gain to be used before a sync word is detected. 2 1:0 FOC_POST_K FOC_LIMIT[1:0] 1 10 R/W R/W 00 K 01 2K 10 3K 11 4K The frequency compensation loop gain to be used after a sync word is detected. 0 Same as FOC_PRE_K 1 K/2 The saturation point for the frequency offset compensation algorithm: 00 0 (no frequency offset compensation) 01 BWCHAN / 8 10 BW CHAN / 4 11 BW CHAN / 2 Frequency offset compensation is not supported for ASK/OOK; Always use FOC_LIMIT=0 with these modulation formats. SWRS033G Page 219 of 244 CC1110Fx / CC1111Fx 0xDF16: BSCFG - Bit Synchronization Configuration Bit Field Name Reset R/W Description 7:6 BS_PRE_KI[1:0] 01 R/W The clock recovery feedback loop integral gain to be used before a sync word is detected (used to correct offsets in data rate): 5:4 3 2 1:0 BS_PRE_KP[1:0] BS_POST_KI BS_POST_KP BS_LIMIT[1:0] 10 1 1 00 R/W R/W R/W R/W 00 KI 01 2KI 10 3KI 11 4KI The clock recovery feedback loop proportional gain to be used before a sync word is detected 00 KP 01 2KP 10 3KP 11 4KP The clock recovery feedback loop integral gain to be used after a sync word is detected. 0 Same as BS_PRE_KI 1 KI /2 The clock recovery feedback loop proportional gain to be used after a sync word is detected. 0 Same as BS_PRE_KP 1 KP The saturation point for the data rate offset compensation algorithm: 00 0 (No data rate offset compensation performed) 01 3.125% data rate offset 10 6.25% data rate offset 11 12.5% data rate offset SWRS033G Page 220 of 244 CC1110Fx / CC1111Fx 0xDF17: AGCCTRL2 - AGC Control Bit Field Name Reset R/W Description 7:6 MAX_DVGA_GAIN[1:0] 00 R/W Reduces the maximum allowable DVGA gain. 5:3 2:0 MAX_LNA_GAIN[2:0] MAGN_TARGET[2:0] 000 011 R/W R/W 00 All gain settings can be used 01 The highest gain setting can not be used 10 The 2 highest gain settings can not be used 11 The 3 highest gain settings can not be used Sets the maximum allowable LNA + LNA 2 gain relative to the maximum possible gain. 000 Maximum possible LNA + LNA 2 gain 001 Approx. 2.6 dB below maximum possible gain 010 Approx. 6.1 dB below maximum possible gain 011 Approx. 7.4 dB below maximum possible gain 100 Approx. 9.2 dB below maximum possible gain 101 Approx. 11.5 dB below maximum possible gain 110 Approx. 14.6 dB below maximum possible gain 111 Approx. 17.1 dB below maximum possible gain These bits set the target value for the averaged amplitude from the digital channel filter (1 LSB = 0 dB). 000 24 dB 001 27 dB 010 30 dB 011 33 dB 100 36 dB 101 38 dB 110 40 dB 111 42 dB SWRS033G Page 221 of 244 CC1110Fx / CC1111Fx 0xDF18: AGCCTRL1 - AGC Control Bit Field Name 7 Reset R/W Description - R0 Not used 6 AGC_LNA_PRIORITY 1 R/W Selects between two different strategies for LNA and LNA2 gain adjustment. When 1, the LNA gain is decreased first. When 0, the LNA2 gain is decreased to minimum before decreasing LNA gain. 5:4 CARRIER_SENSE_REL_THR[1:0] 00 R/W Sets the relative change threshold for asserting carrier sense 3:0 CARRIER_SENSE_ABS_THR[3:0] 0000 R/W 00 Relative carrier sense threshold disabled 01 6 dB increase in RSSI value 10 10 dB increase in RSSI value 11 14 dB increase in RSSI value Sets the absolute RSSI threshold for asserting carrier sense (Equal to channel filter amplitude when AGC has not decreased gain). The 2-complement signed threshold is programmed in steps of 1 dB and is relative to the MAGN_TARGET setting. 1000 (-8) Absolute carrier sense threshold disabled 1001 (-7) 7 dB below MAGN_TARGET setting ... ... 1111 (-1) 1 dB below MAGN_TARGET setting 0000 (0) At MAGN_TARGET setting 0001 (1) 1 dB above MAGN_TARGET setting ... ... 0111 (7) 7 dB above MAGN_TARGET setting SWRS033G Page 222 of 244 CC1110Fx / CC1111Fx 0xDF19: AGCCTRL0 - AGC Control Bit Field Name Reset R/W Description 7:6 HYST_LEVEL[1:0] 10 R/W Sets the level of hysteresis on the magnitude deviation (internal AGC signal that determines gain changes). 5:4 3:2 1:0 WAIT_TIME[1:0] AGC_FREEZE[1:0] FILTER_LENGTH[1:0] 01 00 01 R/W R/W R/W 00 No hysteresis, small symmetric dead zone, high gain 01 Low hysteresis, small asymmetric dead zone, medium gain 10 Medium hysteresis, medium asymmetric dead zone, medium gain 11 Large hysteresis, large asymmetric dead zone, low gain Sets the number of channel filter samples from a gain adjustment has been made until the AGC algorithm starts accumulating new samples. 00 8 01 16 10 24 11 32 Controls when the AGC gain should be frozen. 00 Normal operation. Always adjust gain when required. 01 The gain setting is frozen when a sync word has been found. 10 Manually freeze the analog gain setting and continue to adjust the digital gain. 11 Manually freezes both the analog and the digital gain settings. Used for manually overriding the gain. Sets the averaging length for the amplitude from the channel filter. Sets the OOK/ASK decision boundary for OOK/ASK reception. Please use the SmartRF Studio software [9] for recommended settings. 00 8 01 16 10 32 11 64 0xDF1A: FREND1 - Front End RX Configuration Bit Field Name Reset R/W Description 7:6 LNA_CURRENT[1:0] 01 R/W Adjusts front-end LNA PTAT current output 5:4 LNA2MIX_CURRENT[1:0] 01 R/W Adjusts front-end PTAT outputs 3:2 LODIV_BUF_CURRENT_RX[1:0] 01 R/W Adjusts current in RX LO buffer (LO input to mixer) 1:0 MIX_CURRENT[1:0] 10 R/W Adjusts current in mixer SWRS033G Page 223 of 244 CC1110Fx / CC1111Fx 0xDF1B: FREND0 - Front End TX Configuration Bit Field Name 7:6 5:4 LODIV_BUF_CURRENT_TX[1:0] 3 2:0 PA_POWER[2:0] Reset R/W Description - R0 Not used 01 R/W Adjusts current TX LO buffer (input to PA). The value to use in this field is given by the SmartRF Studio software [9]. - R0 Not used 000 R/W Selects PA power setting. This value is an index to the PATABLE (PA_TABLE7 - PA_TABLE0 registers), which can be programmed with up to 8 different PA settings. In ASK mode, this selects the PATABLE index to use when transmitting a `1'. PATABLE index zero is used in ASK when transmitting a `0'. The PATABLE settings from index `0' to the PA_POWER value are used for ASK TX shaping, and for power ramp-up/ramp-down at the start/end of transmission in all TX modulation formats. 0xDF1C: FSCAL3 - Frequency Synthesizer Calibration Bit Field Name Reset R/W Description 7:6 FSCAL3[7:6] 10 R/W Frequency synthesizer calibration configuration. The value to write in this register before calibration is given by the SmartRF Studio software [9]. 5:4 CHP_CURR_CAL_EN[1:0] 10 R/W Disable charge pump calibration stage when 0 3:0 FSCAL3[3:0] 1001 R/W Frequency synthesizer calibration result register. Digital bit vector defining the charge pump output current, on an exponential scale: IOUT=I0*2FSCAL3[3:0]/4 Fast frequency hopping without calibration for each hop can be done by calibrating upfront for each frequency and saving the resulting FSCAL3, FSCAL2 and FSCAL1 register values. Between each frequency hop, calibration can be replaced by writing the FSCAL3, FSCAL2 and FSCAL1 register values corresponding to the next RF frequency. Note: This register will be in its reset state when returning to active mode from PM2 and PM3. 0xDF1D: FSCAL2 - Frequency Synthesizer Calibration Bit Field Name 7:6 5 4:0 VCO_CORE_H_EN FSCAL2[4:0] Reset R/W Description - R0 Not used 0 R/W Select VCO 01010 R/W 0 Low 1 High Frequency synthesizer calibration result register. VCO current calibration result and override value Fast frequency hopping without calibration for each hop can be done by calibrating upfront for each frequency and saving the resulting FSCAL3, FSCAL2 and FSCAL1 register values. Between each frequency hop, calibration can be replaced by writing the FSCAL3, FSCAL2 and FSCAL1 register values corresponding to the next RF frequency. Note: This register will be in its reset state when returning to active mode from PM2 and PM3. SWRS033G Page 224 of 244 CC1110Fx / CC1111Fx 0xDF1E: FSCAL1 - Frequency Synthesizer Calibration Bit Field Name 7:6 5:0 FSCAL1[5:0] Reset R/W Description - R0 Not used 100000 R/W Frequency synthesizer calibration result register. Capacitor array setting for VCO coarse tuning. Fast frequency hopping without calibration for each hop can be done by calibrating upfront for each frequency and saving the resulting FSCAL3, FSCAL2 and FSCAL1 register values. Between each frequency hop, calibration can be replaced by writing the FSCAL3, FSCAL2 and FSCAL1 register values corresponding to the next RF frequency. Note: This register will be in its reset state when returning to active mode from PM2 and PM3. 0xDF1F: FSCAL0 - Frequency Synthesizer Calibration Bit Field Name 7 6:0 FSCAL0[6:0] Reset R/W Description - R0 Not used 0001101 R/W Frequency synthesizer calibration control. The value to use in this register is given by the SmartRF Studio software [9]. 0xDF23: TEST2 - Various Test Settings Bit Field Name Reset R/W Description 7:0 TEST2[7:0] 0x88 R/W At low data rates, the sensitivity can be improved by changing it to 0x81 (MDMCFG2.DEM_DCFILT_OFF should be 0). 0xDF24: TEST1 - Various Test Settings Bit Field Name Reset R/W Description 7:0 TEST1[7:0] 0x11 R/W Always set this register to 0x31 when being in TX. At low data rates, the sensitivity can be improved by changing it to 0x35 in RX. (MDMCFG2.DEM_DCFILT_OFF should be 0). 0xDF25: TEST0 - Various Test Settings Bit Field Name Reset R/W Description 7:2 TEST0[7:2] 000010 R/W The value to use in this register is given by the SmartRF Studio software [9]. 1 VCO_SEL_CAL_EN 1 R/W Enable VCO selection calibration stage when 1 0 TEST0[0] 1 R/W The value to use in this register is given by the SmartRF Studio software [9]. 0xDF27: PA_TABLE7 - PA Power Setting 7 Bit Field Name Reset R/W Description 7:0 PA_TABLE7[7:0] 0x00 R/W Power amplifier output power setting 7 0xDF28: PA_TABLE6 - PA Power Setting 6 Bit Field Name Reset R/W Description 7:0 PA_TABLE6[7:0] 0x00 R/W Power amplifier output power setting 6 SWRS033G Page 225 of 244 CC1110Fx / CC1111Fx 0xDF29: PA_TABLE5 - PA Power Setting 5 Bit Field Name Reset R/W Description 7:0 PA_TABLE5[7:0] 0x00 R/W Power amplifier output power setting 5 0xDF2A: PA_TABLE4 - PA Power Setting 4 Bit Field Name Reset R/W Description 7:0 PA_TABLE4[7:0] 0x00 R/W Power amplifier output power setting 4 0xDF2B: PA_TABLE3 - PA Power Setting 3 Bit Field Name Reset R/W Description 7:0 PA_TABLE3[7:0] 0x00 R/W Power amplifier output power setting 3 0xDF2C: PA_TABLE2 - PA Power Setting 2 Bit Field Name Reset R/W Description 7:0 PA_TABLE2[7:0] 0x00 R/W Power amplifier output power setting 2 0xDF2D: PA_TABLE1 - PA Power Setting 1 Bit Field Name Reset R/W Description 7:0 PA_TABLE1[7:0] 0x00 R/W Power amplifier output power setting 1 0xDF2E: PA_TABLE0 - PA Power Setting 0 Bit Field Name Reset R/W Description 7:0 PA_TABLE0[7:0] 0x00 R/W Power amplifier output power setting 0 0xDF36: PARTNUM - Chip ID[15:8] Bit Field Name Reset R/W Description 7:0 PARTNUM[7:0] 0x01 CC1110Fx 0x11 CC1111Fx R Chip part number 0xDF37: VERSION - Chip ID[7:0] Bit Field Name Reset R/W Description 7:0 VERSION[7:0] 0x03 R Chip version number. 0xDF38: FREQEST - Frequency Offset Estimate from Demodulator Bit Field Name Reset R/W Description 7:0 FREQOFF_EST 0x00 R The estimated frequency offset (2's complement) of the carrier. Resolution is fRef/214 Range is 202 kHz to 209 kHz for CC1110Fx and 186 kHz for CC1111Fx Frequency offset compensation is only supported for 2-FSK, GFSK, and MSK modulation. This register will read 0 when using ASK or OOK modulation. SWRS033G Page 226 of 244 CC1110Fx / CC1111Fx 0xDF39: LQI - Demodulator Estimate for Link Quality Bit Field Name Reset R/W Description 7 CRC_OK 0 R The last CRC comparison matched. Cleared when entering/restarting RX mode. 6:0 LQI_EST[6:0] 0000000 R The Link Quality Indicator estimates how easily a received signal can be demodulated. Calculated over the 64 symbols following the sync word. 0xDF3A: RSSI - Received Signal Strength Indication Bit Field Name Reset R/W Description 7:0 RSSI 0x80 R Received signal strength indicator 0xDF3B: MARCSTATE - Main Radio Control State Machine State Bit Field Name 7:5 4:0 MARC_STATE[4:0] Reset R/W Description - R0 Not used 0001 R Main Radio Control FSM State Value State Name State (Figure 55, Page202) 00000 SLEEP SLEEP 00001 IDLE IDLE 00010 Not used 00011 VCOON_MC MANCAL 00100 REGON_MC MANCAL 00101 MANCAL MANCAL 00110 VCOON FS_WAKEUP 00111 REGON FS_WAKEUP 01000 STARTCAL CALIBRATE 01001 BWBOOST SETTLING 01010 FS_LOCK SETTLING 01011 IFADCON SETTLING 01100 ENDCAL CALIBRATE 01101 RX RX 01110 RX_END RX 01111 RX_RST RX 10000 TXRX_SWITCH TXRX_SETTLING 10001 RX_OVERFLO W RX_OVERFLOW 10010 FSTXON FSTXON 10011 TX TX 10100 TX_END TX 10101 RXTX_SWITCH RXTX_SETTLING 10110 TX_UNDERFLO W TX_UNDERFLOW SWRS033G Page 227 of 244 CC1110Fx / CC1111Fx 0xDF3C: PKTSTATUS - Packet Status Bit Field Name Reset R/W Description 7 CRC_OK 0 R The last CRC comparison matched. Cleared when entering/restarting RX mode. 6 CS 0 R Carrier sense 5 PQT_REACHED 0 R Preamble Quality reached 4 CCA 0 R Channel is clear 3 SFD 0 R Asserted when sync word has been sent / received, and de-asserted at the end of the packet. In RX, this bit will de-assert when the optional address check fails or the radio enter RX_OVERFLOW state. In TX this bit will deassert if the radio enters TX_UNDERFLOW state. - R0 Not used 2:0 0xDF3D: VCO_VC_DAC - Current Setting from PLL Calibration Module Bit Field Name Reset R/W Description 7:0 VCO_VC_DAC[7:0] 0x94 R Status register for test only. SWRS033G Page 228 of 244 CC1110Fx / CC1111Fx 14 Voltage Regulators The CC1110Fx/CC1111Fx includes a low drop-out voltage regulator. This is used to provide a 1.8 V power supply to the CC1110Fx/CC1111Fx digital power supply. The voltage regulator should not be used to provide power to external circuits because of limited power sourcing capability and also due to noise considerations. The voltage regulator input pin AVDD_DREG is to be connected to the unregulated 2.0 V to 3.6 V power supply. The output of the digital regulator is connected internally in the CC1110Fx/CC1111Fx to the digital power supply. The voltage regulator requires an external decoupling capacitor connected to the DCOUPL pin as described in Section 9 on Page 36. 14.1 Voltage Regulator Power-on The voltage regulator is disabled when the CC1110Fx/CC1111Fx is placed in power modes PM2 or PM3 (see Section 12.1). When the 15 voltage regulator is disabled, register and RAM contents will be retained while the unregulated 2.0 V - 3.6 V power supply is present. Radio Test Output Signals For debug and test purposes, a number of internal status signals in the radio may be output on the port pins P1_7 - P1_5. This debug option is controlled through the RF registers IOCFG2 - IOCFG0. Table 73 shows the value written to IOCFGx.GDOx_CFG[5:0] with the corresponding internal signals that will be output in each case. Setting IOCFGx.GDOx_CFG to a value other than 0 will override the P1SEL_SELP1_7, P1SEL_SELP1_6, and P1SEL_SELP1_5 settings, and the pins will automatically become outputs. SWRS033G Page 229 of 244 CC1110Fx / CC1111Fx GDO0_CFG[5:0] GDO1_CFG[5:0] GDO2_CFG[5:0] Description 000000 The pin is configured according to the I/O registers. See 12.4.7 000001 - 000111 Reserved 001000 Preamble Quality Reached. Asserts when the PQI is above the programmed PQT value. 001001 Clear channel assessment. High when RSSI level is below threshold (dependent on the current CCA_MODE setting) 001010 - 001101 Reserved 001110 Carrier sense. High if RSSI level is above threshold. 001111 CRC_OK. The last CRC comparison matched. Cleared when entering/restarting RX mode. 010000 - 010101 Reserved 010110 RX_HARD_DATA[1]. Can be used together with RX_SYMBOL_TICK for alternative serial RX output. 010111 RX_HARD_DATA[0]. Can be used together with RX_SYMBOL_TICK for alternative serial RX output. 011000 - 011010 Reserved 011011 PA_PD. Can be used to control an external PA or RX/TX switch. Signal is asserted when the radio enters TX state and de-asserted when the radio exits TX state. The signal is active low 011100 LNA_PD. Can be used to control an external LNA or RX/TX switch. Signal is asserted when the radio enters RX state and de-asserted when the radio exits RX state. The signal is active low 011101 RX_SYMBOL_TICK. Can be used together with RX_HARD_DATA for alternative serial RX output. 011110 - 101110 Reserved 101111 HW to 0 (HW1 achieved by setting GDOx_INV=1). Can be used to control an external LNA/PA or RX/TX switch. 110000 - 111111 Reserved Table 73: Radio Test Output Signals SWRS033G Page 230 of 244 CC1110Fx / CC1111Fx 16 Register Overview MPAGE (0x93) - Memory Page Select ......................................................................................... 53 MEMCTR (0xC7) - Memory Arbiter Control ............................................................................... 54 DPH0 (0x83) - Data Pointer 0 High Byte ...................................................................................... 54 DPL0 (0x82) - Data Pointer 0 Low Byte ....................................................................................... 54 DPH1 (0x85) - Data Pointer 1 High Byte ...................................................................................... 54 DPL1 (0x84) - Data Pointer 1 Low Byte ....................................................................................... 54 DPS (0x92) - Data Pointer Select .................................................................................................. 55 PSW (0xD0) - Program Status Word............................................................................................. 55 ACC (0xE0) - Accumulator ........................................................................................................... 56 B (0xF0) - B Register..................................................................................................................... 56 SP (0x81) - Stack Pointer............................................................................................................... 56 IEN1 (0xB8) - Interrupt Enable 1 Register .................................................................................... 63 IEN2 (0x9A) - Interrupt Enable 2 Register.................................................................................... 64 TCON (0x88) - CPU Interrupt Flag 1............................................................................................ 65 S0CON (0x98) - CPU Interrupt Flag 2 .......................................................................................... 66 S1CON (0x9B) - CPU Interrupt Flag 3 ......................................................................................... 66 IRCON (0xC0) - CPU Interrupt Flag 4.......................................................................................... 67 IRCON2 (0xE8) - CPU Interrupt Flag 5........................................................................................ 68 IP1 (0xB9) - Interrupt Priority 1 .................................................................................................... 68 IP0 (0xA9) - Interrupt Priority 0 .................................................................................................... 69 PCON (0x87) - Power Mode Control ............................................................................................ 78 SLEEP (0xBE) - Sleep Mode Control ........................................................................................... 79 CLKCON (0xC6) - Clock Control................................................................................................. 82 FCTL (0xAE) - Flash Control........................................................................................................ 89 FWDATA (0xAF) - Flash Write Data ........................................................................................... 89 FADDRH (0xAD) - Flash Address High Byte .............................................................................. 89 FADDRL (0xAC) - Flash Address Low Byte ............................................................................... 89 FWT (0xAB) - Flash Write Timing ............................................................................................... 89 P0 (0x80) - Port 0........................................................................................................................... 95 P1 (0x90) - Port 1........................................................................................................................... 95 P2 (0xA0) - Port 2.......................................................................................................................... 95 PERCFG (0xF1) - Peripheral Control............................................................................................ 95 ADCCFG (0xF2) - ADC Input Configuration............................................................................... 96 P0SEL (0xF3) - Port 0 Function Select ......................................................................................... 96 P1SEL (0xF4) - Port 1 Function Select ......................................................................................... 96 P2SEL (0xF5) - Port 2 Function Select ......................................................................................... 97 P0DIR (0xFD) - Port 0 Direction................................................................................................... 97 P1DIR (0xFE) - Port 1 Direction ................................................................................................... 97 P2DIR (0xFF) - Port 2 Direction ................................................................................................... 98 P0INP (0x8F) - Port 0 Input Mode ................................................................................................ 98 P1INP (0xF6) - Port 1 Input Mode ................................................................................................ 98 P2INP (0xF7) - Port 2 Input Mode ................................................................................................ 98 P0IFG (0x89) - Port 0 Interrupt Status Flag .................................................................................. 99 P1IFG (0x8A) - Port 1 Interrupt Status Flag.................................................................................. 99 P2IFG (0x8B) - Port 2 Interrupt Status Flag.................................................................................. 99 PICTL (0x8C) - Port Interrupt Control ........................................................................................ 100 P1IEN (0x8D) - Port 1 Interrupt Mask ........................................................................................ 100 DMAARM (0xD6) - DMA Channel Arm ................................................................................... 109 DMAREQ (0xD7) - DMA Channel Start Request and Status ..................................................... 110 DMA0CFGH (0xD5) - DMA Channel 0 Configuration Address High Byte .............................. 110 DMA0CFGL (0xD4) - DMA Channel 0 Configuration Address Low Byte ............................... 110 DMA1CFGH (0xD3) - DMA Channel 1 - 4 Configuration Address High Byte ......................... 110 DMA1CFGL (0xD2) - DMA Channel 1 - 4 Configuration Address Low Byte .......................... 110 SWRS033G Page 231 of 244 CC1110Fx / CC1111Fx DMAIRQ (0xD1) - DMA Interrupt Flag ..................................................................................... 111 ENDIAN (0x95) - USB Endianess Control (CC1111Fx)................................................................ 111 T1CNTH (0xE3) - Timer 1 Counter High ................................................................................... 120 T1CNTL (0xE2) - Timer 1 Counter Low .................................................................................... 120 T1CTL (0xE4) - Timer 1 Control and Status............................................................................... 120 T1CCTL0 (0xE5) - Timer 1 Channel 0 Capture/Compare Control ............................................. 121 T1CC0H (0xDB) - Timer 1 Channel 0 Capture/Compare Value High........................................ 121 T1CC0L (0xDA) - Timer 1 Channel 0 Capture/Compare Value Low ........................................ 121 T1CCTL1 (0xE6) - Timer 1 Channel 1 Capture/Compare Control ............................................. 122 T1CC1H (0xDD) - Timer 1 Channel 1 Capture/Compare Value High ....................................... 122 T1CC1L (0xDC) - Timer 1 Channel 1 Capture/Compare Value Low......................................... 122 T1CCTL2 (0xE7) - Timer 1 Channel 2 Capture/Compare Control ............................................. 123 T1CC2H (0xDF) - Timer 1 Channel 2 Capture/Compare Value High ........................................ 123 T1CC2L (0xDE) - Timer 1 Channel 2 Capture/Compare Value Low......................................... 123 T2CTL (0x9E) - Timer 2 Control ................................................................................................ 125 T2CT (0x9C) - Timer 2 Count..................................................................................................... 125 T2PR (0x9D) - Timer 2 Prescaler ................................................................................................ 125 WORTIME0 (0xA5) - Sleep Timer Low Byte ............................................................................ 127 WORTIME1 (0xA6) - Sleep Timer High Byte ........................................................................... 128 WOREVT1 (0xA4) - Sleep Timer Event0 Timeout High ........................................................... 128 WOREVT0 (0xA3) - Sleep Timer Event0 Timeout Low............................................................ 128 WORCTRL (0xA2) - Sleep Timer Control ................................................................................. 128 WORIRQ (0xA1) - Sleep Timer Interrupt Control...................................................................... 128 T3CNT (0xCA) - Timer 3 Counter .............................................................................................. 132 T3CTL (0xCB) - Timer 3 Control ............................................................................................... 133 T3CCTL0 (0xCC) - Timer 3 Channel 0 Compare Control.......................................................... 134 T3CC0(0xCD) - Timer 3 Channel 0 Compare Value .................................................................. 134 T3CCTL1 (0xCE) - Timer 3 Channel 1 Compare Control .......................................................... 135 T3CC1 (0xCF) - Timer 3 Channel 1 Compare Value.................................................................. 135 T4CNT (0xEA) - Timer 4 Counter .............................................................................................. 135 T4CTL (0xEB) - Timer 4 Control................................................................................................ 136 T4CCTL0 (0xEC) - Timer 4 Channel 0 Compare Control .......................................................... 137 T4CC0 (0xED) - Timer 4 Channel 0 Compare Value ................................................................. 137 T4CCTL1 (0xEE) - Timer 4 Channel 1 Compare Control .......................................................... 138 T4CC1 (0xEF) - Timer 4 Channel 1 Compare Value .................................................................. 138 TIMIF (0xD8) - Timers 1/3/4 Interrupt Mask/Flag ..................................................................... 139 ADCL (0xBA) - ADC Data Low................................................................................................. 143 ADCH (0xBB) - ADC Data High ................................................................................................ 143 ADCCON1 (0xB4) - ADC Control 1 .......................................................................................... 143 ADCCON2 (0xB5) - ADC Control 2 .......................................................................................... 144 ADCCON3 (0xB6) - ADC Control 3 .......................................................................................... 145 RNDL (0xBC) - Random Number Generator Data Low Byte .................................................... 147 RNDH (0xBD) - Random Number Generator Data High Byte ................................................... 147 ENCCS (0xB3) - Encryption Control and Status......................................................................... 149 ENCDI (0xB1) - Encryption Input Data ...................................................................................... 149 ENCDO (0xB2) - Encryption Output Data.................................................................................. 149 WDCTL (0xC9) - Watchdog Timer Control ............................................................................... 151 U0CSR (0x86) - USART 0 Control and Status ........................................................................... 157 U0UCR (0xC4) - USART 0 UART Control................................................................................ 158 U0GCR (0xC5) - USART 0 Generic Control .............................................................................. 158 U0DBUF (0xC1) - USART 0 Receive/Transmit Data Buffer ..................................................... 159 U0BAUD (0xC2) - USART 0 Baud Rate Control....................................................................... 159 U1CSR (0xF8) - USART 1 Control and Status ........................................................................... 159 U1UCR (0xFB) - USART 1 UART Control ............................................................................... 160 SWRS033G Page 232 of 244 CC1110Fx / CC1111Fx U1GCR (0xFC) - USART 1 Generic Control.............................................................................. 160 U1DBUF (0xF9) - USART 1 Receive/Transmit Data Buffer ..................................................... 161 U1BAUD (0xFA) - USART 1 Baud Rate Control ...................................................................... 161 0xDF40: I2SCFG0 - I2S Configuration Register 0 ...................................................................... 166 0xDF41: I2SCFG1 - I2S Configuration Register 1 ...................................................................... 167 0xDF42: I2SDATL - I2S Data Low Byte..................................................................................... 167 0xDF43: I2SDATH - I2S Data High Byte.................................................................................... 167 0xDF44: I2SWCNT - I2S Word Count Register.......................................................................... 167 0xDF45: I2SSTAT - I2S Status Register...................................................................................... 168 0xDF46: I2SCLKF0 - I2S Clock Configuration Register 0 ......................................................... 168 0xDF47: I2SCLKF1 - I2S Clock Configuration Register 1 ......................................................... 168 0xDF48: I2SCLKF2 - I2S Clock Configuration Register 2 ......................................................... 168 0xDE00: USBADDR - Function Address ................................................................................... 178 0xDE01: USBPOW - Power/Control Register ............................................................................ 178 0xDE02: USBIIF - IN Endpoints and EP0 Interrupt Flags.......................................................... 178 0xDE04: USBOIF - Out Endpoints Interrupt Flags..................................................................... 178 0xDE06: USBCIF - Common USB Interrupt Flags..................................................................... 179 0xDE07: USBIIE - IN Endpoints and EP0 Interrupt Enable Mask ............................................. 179 0xDE09: USBOIE - Out Endpoints Interrupt Enable Mask ........................................................ 180 0xDE0B: USBCIE - Common USB Interrupt Enable Mask ....................................................... 180 0xDE0C: USBFRML - Current Frame Number (Low byte) ....................................................... 180 0xDE0D: USBFRMH - Current Frame Number (High byte) ...................................................... 181 0xDE0E: USBINDEX - Current Endpoint Index Register .......................................................... 181 0xDE10: USBMAXI - Max. Packet Size for IN Endpoint{1 - 5} ............................................... 181 0xDE11: USBCS0 - EP0 Control and Status (USBINDEX=0) ................................................... 181 0xDE11: USBCSIL - IN EP{1 - 5} Control and Status Low ...................................................... 182 0xDE12: USBCSIH - IN EP{1 - 5} Control and Status High ..................................................... 182 0xDE13: USBMAXO - Max. Packet Size for OUT{1 - 5} Endpoint ......................................... 182 0xDE14: USBCSOL - OUT EP{1 - 5} Control and Status Low................................................. 183 0xDE15: USBCSOH - OUT EP{1 - 5} Control and Status High................................................ 183 0xDE16: USBCNT0 - Number of Received Bytes in EP0 FIFO (USBINDEX=0)..................... 183 0xDE16: USBCNTL - Number of Bytes in EP{1 - 5} OUT FIFO Low ..................................... 183 0xDE17: USBCNTH - Number of Bytes in EP{1 - 5} OUT FIFO High .................................... 184 0xDE20: USBF0 - Endpoint 0 FIFO............................................................................................ 184 0xDE22: USBF1 - Endpoint 1 FIFO............................................................................................ 184 0xDE24: USBF2 - Endpoint 2 FIFO............................................................................................ 184 0xDE26: USBF3 - Endpoint 3 FIFO............................................................................................ 184 0xDE28: USBF4 - Endpoint 4 FIFO............................................................................................ 184 0xDE2A: USBF5 - Endpoint 5 FIFO........................................................................................... 184 RFIF (0xE9) - RF Interrupt Flags ................................................................................................ 188 RFIM (0x91) - RF Interrupt Mask ............................................................................................... 189 0xDF2F: IOCFG2 - Radio Test Signal Configuration (P1_7) ..................................................... 211 0xDF30: IOCFG1 - Radio Test Signal Configuration (P1_6) ..................................................... 211 0xDF31: IOCFG0 - Radio Test Signal Configuration (P1_5) ..................................................... 211 0xDF00: SYNC1 - Sync Word, High Byte.................................................................................. 211 0xDF01: SYNC0 - Sync Word, Low Byte .................................................................................. 211 0xDF02: PKTLEN - Packet Length............................................................................................. 211 0xDF03: PKTCTRL1 - Packet Automation Control ................................................................... 212 0xDF04: PKTCTRL0 - Packet Automation Control ................................................................... 212 0xDF05: ADDR - Device Address .............................................................................................. 213 0xDF06: CHANNR - Channel Number....................................................................................... 213 0xDF07: FSCTRL1 - Frequency Synthesizer Control................................................................. 213 0xDF08: FSCTRL0 - Frequency Synthesizer Control................................................................. 213 0xDF09: FREQ2 - Frequency Control Word, High Byte ............................................................ 213 SWRS033G Page 233 of 244 CC1110Fx / CC1111Fx 0xDF0A: FREQ1 - Frequency Control Word, Middle Byte........................................................ 213 0xDF0B: FREQ0 - Frequency Control Word, Low Byte ............................................................ 213 0xDF0C: MDMCFG4 - Modem configuration............................................................................ 214 0xDF0D: MDMCFG3 - Modem Configuration........................................................................... 214 0xDF0E: MDMCFG2 - Modem Configuration ........................................................................... 215 0xDF0F: MDMCFG1 - Modem Configuration ........................................................................... 216 0xDF10: MDMCFG0 - Modem Configuration ........................................................................... 216 0xDF11: DEVIATN - Modem Deviation Setting........................................................................ 217 0xDF12: MCSM2 - Main Radio Control State Machine Configuration...................................... 217 0xDF13: MCSM1 - Main Radio Control State Machine Configuration...................................... 218 0xDF14: MCSM0 - Main Radio Control State Machine Configuration...................................... 218 0xDF15: FOCCFG - Frequency Offset Compensation Configuration ........................................ 219 0xDF16: BSCFG - Bit Synchronization Configuration ............................................................... 220 0xDF17: AGCCTRL2 - AGC Control......................................................................................... 221 0xDF18: AGCCTRL1 - AGC Control......................................................................................... 222 0xDF19: AGCCTRL0 - AGC Control......................................................................................... 223 0xDF1A: FREND1 - Front End RX Configuration ..................................................................... 223 0xDF1B: FREND0 - Front End TX Configuration ..................................................................... 224 0xDF1C: FSCAL3 - Frequency Synthesizer Calibration............................................................. 224 0xDF1D: FSCAL2 - Frequency Synthesizer Calibration ............................................................ 224 0xDF1E: FSCAL1 - Frequency Synthesizer Calibration............................................................. 225 0xDF1F: FSCAL0 - Frequency Synthesizer Calibration ............................................................. 225 0xDF23: TEST2 - Various Test Settings ..................................................................................... 225 0xDF24: TEST1 - Various Test Settings ..................................................................................... 225 0xDF25: TEST0 - Various Test Settings ..................................................................................... 225 0xDF27: PA_TABLE7 - PA Power Setting 7 ............................................................................. 225 0xDF28: PA_TABLE6 - PA Power Setting 6 ............................................................................. 225 0xDF29: PA_TABLE5 - PA Power Setting 5 ............................................................................. 226 0xDF2A: PA_TABLE4 - PA Power Setting 4............................................................................. 226 0xDF2B: PA_TABLE3 - PA Power Setting 3............................................................................. 226 0xDF2C: PA_TABLE2 - PA Power Setting 2............................................................................. 226 0xDF2D: PA_TABLE1 - PA Power Setting 1............................................................................. 226 0xDF2E: PA_TABLE0 - PA Power Setting 0 ............................................................................. 226 0xDF36: PARTNUM - Chip ID[15:8]......................................................................................... 226 0xDF37: VERSION - Chip ID[7:0] ............................................................................................. 226 0xDF38: FREQEST - Frequency Offset Estimate from Demodulator ........................................ 226 0xDF39: LQI - Demodulator Estimate for Link Quality ............................................................. 227 0xDF3A: RSSI - Received Signal Strength Indication ................................................................ 227 0xDF3B: MARCSTATE - Main Radio Control State Machine State ......................................... 227 0xDF3C: PKTSTATUS - Packet Status ...................................................................................... 228 0xDF3D: VCO_VC_DAC - Current Setting from PLL Calibration Module .............................. 228 SWRS033G Page 234 of 244 CC1110Fx / CC1111Fx 17 Package Description (QFN 36) available in RoHS lead-free package only. Compliant with JEDEC: MO-220. All dimensions are in millimeters, angles in degrees. Note: The CC1110Fx/CC1111Fx is Figure 62: Package Dimensions Drawing Quad Leadless Package (QLP) QFN 36 Min Max A A1 A2 D D1 E E1 0.80 0.005 0.60 5.90 5.65 5.90 5.65 0.85 0.025 0.65 6.00 5.75 6.00 5.75 0.90 0.045 0.70 6.10 5.85 6.10 5.85 e 0.50 b L 0.18 0.45 0.23 0.55 0.30 0.65 D2 E2 4.40 4.40 Table 74: Package Dimensions SWRS033G Page 235 of 244 CC1110Fx / CC1111Fx 17.1 Recommended PCB Layout for Package (QFN 36) Figure 63: Recommended PCB Layout for QFN 36 Package Note: The figure is an illustration only and not to scale. There are nine 14 mil diameter via holes distributed symmetrically in the ground pad under the package. See also the CC1110EM reference design [1] and theCC1111 USB-Dongle reference design [4]. Thermal Resistance Air velocity [m/s] 0 Rth,j-a [C/W] 32 Table 75: Thermal Properties of QFN 36 Package 17.2 Soldering information The recommendations for lead-free reflow in IPC/JEDEC J-STD-020D should be followed. The lead finish is annealed (150 C for 1 hr) pure matte tin. 17.3 Tray Specification Tray Specification Package Tray Length Tray Width Tray Height Units per Tray QFN 36 322.6 mm 135.9 mm 7.62 mm 490 Table 76: Tray Specification SWRS033G Page 236 of 244 CC1110Fx / CC1111Fx 17.4 Carrier Tape and Reel Specification Carrier tape and reel is in accordance with EIA Specification 481. Tape and Reel Specification Package Carrier Tape Width Component Pitch Hole Pitch Reel Diameter Reel Hub Diameter Units per Reel QFN 36 16 mm 12 mm 4 mm 13 inches 100 mm 2500 Table 77: Carrier Tape and Reel Specification 18 Ordering Information Ordering Part Number CC1110F8RSP CC1110F8RSPR CC1110F16RSP CC1110F16RSPR CC1110F32RSP CC1110F32RSPR CC1111F8RSP CC1111F8RSPR CC1111F16RSP CC1111F16RSPR CC1111F32RSP CC1111F32RSPR Description Minimum Order Quantity 8 kB flash, 1 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 8 kB flash, 1 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 16 kB flash, 2 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 16 kB flash, 2 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 32 kB flash, 4 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 32 kB flash, 4 kB RAM, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 8 kB flash, 1 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 8 kB flash, 1 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 16 kB flash, 2 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 16 kB flash, 2 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 32 kB flash, 4 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, Tray with 490 pcs per tray. 32 kB flash, 4 kB RAM, full-speed USB, System-on-Chip RF Transceiver. QFN 36 package, RoHS compliant Pb-free assembly, T&R with 2500 pcs per reel. 490 2500 490 2500 490 2500 490 2500 490 2500 490 2500 CC1110-CC1111DK CC1110Fx and CC1111Fx Development Kit 1 CC1110EMK433 CC1110 Evaluation Module Kit, for 433 MHz operation 1 CC1110EMK868-915 CC1110 Evaluation Module Kit, for 868/915 MHz operation 1 CC1111EMK868-915 CC1111 Evaluation Module Kit, for 868/915 MHz operation 1 Table 78: Ordering Information SWRS033G Page 237 of 244 CC1110Fx / CC1111Fx 19 References [1] CC1110EM315 Reference Design (swrr050.zip) [2] CC1110EM433 Reference Design (swrr047.zip) [3] CC1110EM868 - 915 Reference Design (swrr049.zip) [4] CC1111 USB-Dongle Reference Design (swrr049.zip) [5] NIST FIPS Pub 197: Advanced Encryption Standard (AES), Federal Information Processing Standards Publication 197, US Department of Commerce/N.I.S.T., November 26, 2001. Available from the NIST website. http://csrc.nist.gov/publications/fips/fips197/fips-197.pdf [6] Universal Serial Bus Revision 2.0 Specification. Available from the USB Implementors Forum website. http://www.usb.org/developers/docs/ [7] 2 I S bus specification, Philips Semiconductors, Available from the Philips Semiconductors website. http://www.semiconductors.philips.com/acrobat_download/various/I2SBUS.pdf [8] IEEE Std 1241-2000, IEEE standard for terminology and test methods for analog-to-digital converters. [9] SmartRF Studio (swrc046.zip) [10] AN001 SRD regulations for license free transceiver operation(swra090.pdf) [11] ISM-Band and Short Range Device Regulatory Compliance Overview (swra048.pdf) [12] DN006 CC11xx settings for FCC15.247 Solutions (swra123.pdf) [13] AN050 Using the CC1101 in the European 868 MHz SRD band (swra146.pdf) [14] DN016 Compact Antenna Solutions for 868/915MHz (swra160.pdf) [15] DN110 State Transition Times on CC111xFx and CC251xFx(swra191.pdf) (R) [16] DN505 RSSI Interpretation and Timing (swra114.pdf) SWRS033G Page 238 of 244 CC1110Fx / CC1111Fx 20 General Information 20.1 Document History Revision Date Description/Changes SWRS033 2006.01.04 First release SWRS033A 2006.05.11 Preliminary status updated SWRS033B 2007.09.14 First data sheet for released product. Preliminary data sheets exist for engineering samples and pre-production prototype devices, but these data sheets are not complete and may be incorrect in some aspects compared with the released product. SWRS033C 2007.09.20 Data sheet update before release of product. - Operating frequency range changed to 391 - 464 MHz and 782 - 928 MHz - Changed restricted range for PA power in Section 13.15 (now 0x68 to 0x6F) - Added information about register TEST1 when TX-if-CCA is to be used - Changed register FREQEST and FSCTRL0 max range from 20910 to 209 - Added reference to SmartRF Studio for register MCSM0. - Changed bit description for bit FSCAL2.VCO_CORE_H_EN - Added Section 12.1.5.2, describing data rate limitations caused by system clock speed - Added power numbers for RX (Table 6) when using other system clock speeds SWRS033D 2007.10.19 Data sheet update before release of CC1111Fx. - Electrical Specification Section 6 updated with CC1111Fx performance - Minimum power down time of CC1110Fx high speed crystal oscillator stated in Section 6.4.1, Section 6.4.2, Section 12.1.1 and Section 12.1.5.1. - Removed 3rd overtone crystal option for CC1111Fx - Replaced Figure 14, Figure 15, and Figure 16 to correct error in address ranges. - Fixed Table 32 - Fixed bit range for register FADDRH and stated that register WORTIME0 and WORTIME1 defines a combined 16 bit word (WORTIME) - Replaced all occurrences of WORCTL with WORCTRL - Made consistent use of VDD for power with reference to power pin if so needed - Corrected part number for these devices, register PARTNUM - Stated that P1_0 and P1_1 does not have pull capability in register P2INP - Corrected code example in Figure 49 - Corrected unimplemented RAM range in Section 10.2.3.1 - Updated Sections 12.1.3, 12.1.5.1, and 12.1.5.3 with information about system clock source change - Rewrote RAM range in Section 12.3.2 - Updated Section 12.8.2 with information about power modes. Changed code examples - Changed heading text for Section 12.8.5 - Corrected received symbol write and read location in Section 13.11.2 SWRS033E 2007.10.26 - Corrected Table of contents - Updated guard time and stated for which crystal this applies in Table 11 SWRS033G Page 239 of 244 CC1110Fx / CC1111Fx Revision Date Description/Changes SWRS033F 2007.11.23 - Changed title on front page - TX power consumption @ 1.2 kBaud, -6 dBm output power changed to 15.2 mA on front page - "Crystal shunt capacitance" changed to C0 in Table 13 - Temperature coefficient changed to 2.47 mV/C in Table 17 - Zout @ 868/915 MHz = 86.5 + j43 changed to Zout @ 868 MHz = 86.5 + j43 - Changed component name in Figure 10, Figure 11, and Figure 12 in accordance with reference designs and added optional filter in Figure 11 and Figure 12 - Table 28: Made changes to component names and descriptions - Table 29: Changes to component names. Added components for optional filter. R2626/R263 changed to 33 . C203/C214 changed to 22 pF - Table 37: Added footer explaining opcode for ACALL and AJMP - CLKCON.OSC bit. Changed description. It is not longer necessary to set SLEEP.OSC_PD=0 to power up the HS crystal oscillator. - 10.5.1: Added note emphasizing that an interrupt must not be enabled without having proper code located at the corresponding interrupt vector address - :10.5.2: Changes made to code example. - 12.1.5: Changed HS crystal oscillator operating range to 26 - 27 MHz - 12.1.5.1: Changed HS crystal oscillator operating range to 26 - 27 MHz and HS RCOSC operating range to 13 - 13.5 MHz - 12.1.5.1 and 12.1.7: Added info regarding retention of HS RCOSC calibration result. - 12.1.5.2: Rewritten to improve readability - 12.1.5.3: Changed low power RCOSC range to 34.667 - 36 kHz. Added/rewritten info regarding calibration of the low power RCOSC. - 12.5: Chapter rewritten to be more consistent in the use of the terms "transfer" and "transfer count". Added new info regarding the LEN setting. Changes made to Figure 26 and Figure 27 - 12.6.2.1 and 12.6.2.2: Emphasized that the timer wraps around/is loaded with 0x0000 on the next timer tick after the terminal count value is reached - 12.8.4: Added more detailed info about interrupt and associated flags - 12.9.3 and 12.9.3.1 Emphasized that the timer wraps around/is loaded with 0x00 on the next timer tick after the terminal count value is reached - USBCIF.RESUMIF changed to USBCIF.RESUMEIF several places in the document - 13.7.1: Added note saying that frequency offset compensation is not supported for ASK/OOK - 13.11.2: Added note saying that when FEC is used, CLKCON.CLKSPD must be 000 -.PKTCTRL0: Bit 3 set as reserved - FSCTRL0: Changed range to 202 kHz to 209 kHz for CC1110Fx - MDMCFG2.DEM_DCFILT_OFF=1: Only for data rates 100 kBaud: - MDMCFG2.MOD_FORMAT: Added setting for ASK/OOK - MCSM2.RX_TIME_RSSI: Added note regarding ASK/OOK modulation - FOCCFG.FOC_LIMIT: Added note regarding ASK/OOK modulation AGCCTRL0.FILTER_LENGTH Added note regarding ASK/OOK modulation - TEST2: Changed value for improved sensitivity - FREQEST: Changed range to 202 kHz to 209 kHz for CC1110Fx. Added info regarding ASK/OOK modulation - LQI.CRC_OK: Removed reference to CC2400_EN bit, which has been removed SWRS033G Page 240 of 244 CC1110Fx / CC1111Fx Revision Date Description/Changes SWRS033G 2008.07.11 - Changed description of T1CCTL1.MODE bit. - UxGDR changed to UxGCR several places in the document - Changed FREQ2.FREQ[21:16] reset value from 11110 to 011110 - Added changes to the DEVIATN register, and added also info regarding the same register to sections 13.9.1, 13.9.2, and 13.9.3 - 12.14.2.2: Changed description of the UxCSR.ACTIVE bit - 12.8: Added note stating that the Sleep timer should not be used in active mode. This info has in earlier edition only been available in section 8.1 - Added section 9.4: Reference Signal - Table 57 and Table 58: Fsck changed to Fs - 12.8.1: WOREVT1 = desired event0; changed to WOREVT1 = desired event0 >> 8; - Table 39: Added footnote saying that the Sleep Timer compare interrupt has additional interrupt mask bits and interrupt flags found in its SFRs - Updated Figure 26 - Changed the description of PKTSTATUS.SFD - MCSM0.FS_AUTOCAL=1 changed to MCSM0.FS_AUTOCAL=01 and MCSM0.FS_AUTOCAL=0 changed to MCSM0.FS_AUTOCAL=00 throughout the document - 13.1: Added note about SIDLE strobe - Table 16, Table 71, and Section 13.18: Changed the state transition timing - 13.10.3: Added reference to DN505 [16] regarding RSSI response time. - Changes made to the description of I2SCFG0.ULAWE and I2SCFG0.ULAWC - Section 13.9 and 13.9.2 and MDMCFG2 register: Added info saying that Manchester encoding/decoding should not be used when using MSK modulation. - Table 11: Changes done to the condition/note on Power Down Guard Time - Added Section 6.11.1 (info regarding the RESET_N pin being sensitive to noise) - Changes made to the ADCCON1 register. - Changes made to Section 12.11.2.1 regarding how to generate pseudo-random bytes. - Section13.3.1.1: Added note explaining how the RFTXRXIF flag should be cleared when it is not cleared by HW. - The drive strength for I/O pins in output mode is not controlled by the PICTL register but by IOCFG1.GDO_DS. This has been changes several places in the data sheet. - Table 14: Changed the minimum calibrated frequency to 34.7 kHz Removed the Sleep Timer trigger for the DMA since the Sleep Timer should not be used in active mode. - Section 13.12.1: Added note regarding RSSI response time when using MCSM1.RXOFF_MODE=11 - Changed the description of the T2CTL.INT field - Several changes added throughout the document regarding calibration of the two RC oscillators - Added info several places in the document stating that the I2S interface will have precedence in cases where other peripherals (except for the debug interface) are configured to be on the same location even if the pins are configured to be general purpose I/O pins. - Table 78: Changed ordering information for the Development Kits (DKs) - QLP36 / QLP 36 replaced by QFN 36 -12.8.2: Changes made to the description on how entering PM{0 - 2}, updating EVENT0, and resetting the sleep timer should be done with respect to the 32 kHz clock source. Table 79: Document History SWRS033G Page 241 of 244 CC1110Fx / CC1111Fx 20.2 Product Status Definitions Data Sheet Identification Product Status Definition Advance Information Planned or Under Development This data sheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary Experimental and Prototype Devices This data sheet contains preliminary data, and supplementary data will be published at a later date. Texas Instruments reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. The product at this point is not yet fully qualified. No Identification Noted Full Production This data sheet contains the final specifications. Texas Instruments reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Obsolete Not In Production This data sheet contains specifications on a product that has been discontinued by Texas Instruments. The data sheet is printed for reference information only. Table 80: Product Status Definitions SWRS033G Page 242 of 244 CC1110Fx / CC1111Fx 21 Address Information Texas Instruments Norway AS Gaustadalleen 21 N-0349 Oslo NORWAY Tel: +47 22 95 85 44 Fax: +47 22 95 85 46 Web site: http://www.ti.com/lpw 22 TI Worldwide Technical Support Internet TI Semiconductor Product Information Center Home Page: TI Semiconductor KnowledgeBase Home Page: support.ti.com support.ti.com/sc/knowledgebase Product Information Centers Americas Phone: Fax: Internet/Email: +1(972) 644-5580 +1(972) 927-6377 support.ti.com/sc/pic/americas.htm Europe, Middle East and Africa Phone: Belgium (English) Finland (English) France Germany Israel (English) Italy Netherlands (English) Russia Spain Sweden (English) United Kingdom Fax: Internet: +32 (0) 27 45 54 32 +358 (0) 9 25173948 +33 (0) 1 30 70 11 64 +49 (0) 8161 80 33 11 180 949 0107 800 79 11 37 +31 (0) 546 87 95 45 +7 (4) 95 98 10 701 +34 902 35 40 28 +46 (0) 8587 555 22 +44 (0) 1604 66 33 99 +49 (0) 8161 80 2045 support.ti.com/sc/pic/euro.htm Japan Fax International +81-3-3344-5317 Internet/Email Domestic International 0120-81-0036 support.ti.com/sc/pic/japan.htm Domestic www.tij.co.jp/pic SWRS033G Page 243 of 244 CC1110Fx / CC1111Fx Asia Phone Fax Email Internet International +886-2-23786800 Domestic Australia China Hong Kong India Indonesia Korea Malaysia New Zealand Philippines Singapore Taiwan Thailand Toll-Free Number 1-800-999-084 800-820-8682 800-96-5941 +91-80-51381665 (Toll) 001-803-8861-1006 080-551-2804 1-800-80-3973 0800-446-934 1-800-765-7404 800-886-1028 0800-006800 001-800-886-0010 +886-2-2378-6808 tiasia@ti.com or ti-china@ti.com support.ti.com/sc/pic/asia.htm SWRS033G Page 244 of 244 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CC1110F16RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CC1110F32RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CC1110F8RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.5 12.0 16.0 Q2 CC1111F16RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.1 12.0 16.0 Q2 CC1111F32RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.1 12.0 16.0 Q2 CC1111F8RSPR VQFN RSP 36 2500 330.0 16.4 6.3 6.3 1.1 12.0 16.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Jul-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CC1110F16RSPR VQFN RSP 36 2500 378.0 70.0 346.0 CC1110F32RSPR VQFN RSP 36 2500 378.0 70.0 346.0 CC1110F8RSPR VQFN RSP 36 2500 378.0 70.0 346.0 CC1111F16RSPR VQFN RSP 36 2500 378.0 70.0 346.0 CC1111F32RSPR VQFN RSP 36 2500 378.0 70.0 346.0 CC1111F8RSPR VQFN RSP 36 2500 378.0 70.0 346.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP(R) Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee(R) Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2010, Texas Instruments Incorporated