E3X-NA11 - Omron - Datasheet.Directory

E3X-NA6 E3X-SD6

E3X-SD/NA Series

NEW Digital Display – Direct Key Setting

Simple Fiber Amplifiers

Bar Display – Manual Setting

The Series now includes models with digital displays and direct key setting.

Simplicity and High Performance

A design that focuses on simple operation has resulted in an Amplifier that is so simple it can be

operated without the manual.

The Amplifier also uses a large, easy-to-read operation indicator and a simple display for

excess gain (i.e., incident level/operating level).

Essentially anyone can use the Amplifier right away.

With the E3X-SD, settings and

management can be

performed reliably using the

digital display ranging from 0%

to 999% (10 times), and with

the E3X-NA, the same can be

performed intuitively using the

large 5-level bar display.

Operation and Displays So Simple That Anyone Can Use the Amplifier Right Away

Wire-saving Connector to Reduce Work and Stock Management

2• Large reduction in wiring work

• Simple management:

No distinction between master

and slaves

Work efficiency is

also improved during

maintenance.

Gang-mount up to 16 Amplifiers.

Power supply pin

Master Connector

Slave Connector

E3X-NA

E3X-SD

A timer function is provided as a standard feature.

The switch is for the timer only,

so no complicated operation is required.

Compact No modes

10 mm

Small body with width of 10 mm and

simple operation.

Compact size with length of 65 mm.

No manual

No screwdriver

Slide

Intuitive display

for excess gain

(i.e., incident level/operating level)

Large, easy-to-read

operation indicator

120%

· · ·

999%

Operating level

110%

90%

80%

Largest display

in the industry

Large bar display with five levels:

80%, 90%, 100%, 110%, and 120%

100%

Stable light

interruption

Stable incident light

Fine adjustments can be made in

increments of 1% using the Up

and Down Keys.

Setting is completed with a

single press when teaching

with/without the workpiece.

Fine tuning can be

performed using the

8-turn adjuster

(with indicator).

Immediately determine

operation and amount

of light with a simple,

bright display.

Power is supplied through

the connector, so only one

wire for output is required

for expansion.

Simplicity and High Performance

Precision

700 mm

3 m

Distance

14 m

Super-long-distance

Fiber Unit

E32-T17L

Standard Fiber Unit +

Long-distance Lens

E32-TC200+E39-F1

Long-distance Fiber Unit

E32-T11L

The three most important performance

capabilities when selecting a sensor are

achieved to a high standard: distance, speed,

and precision.

A balance is provided between reliable

detection performance and capability for a

broad range of applications.

Distance

Speed

General-purpose Performance for Simple Use

Optical communications is used between Amplifiers.

Interference is reliably prevented for up to five Amplifiers by mutually staggering the light emission timing

(except for the E3X-NA@F).

Optical Communications to Prevent Mutual Interference for Up to Five Amplifiers

400 mm

Standard Fiber Unit

E32-TC200

Sufficient distance performance.

A maximum distance of 14 m

can be achieved by using a

Long-distance Fiber Unit

(through-beam) in combination

with the Amplifier.

Gold wire with a diameter of 30 µm can

be detected.

And minute workpieces can be detected.

Note: The diameter of 30 µm is a typical value

when the sensing distance and sensitivity are

set to their optimal conditions.

The response speed handles 2,500

counts per second to enable detecting

high-speed workpieces

(25,000 counts per second for the E3X-NA@F).

High-speed response of 200 µm

and reliable interference

prevention for up to five Amplifiers

Up to

five Amplifiers

Balanced

application capabilities

E3X-SD

High-speed Models

Long-distance Models

2,500 counts/second

30-µm dia.

200 µs

Optical communications

Simplicity and High Performance

E3X-SD@

Standard

Amplifiers

Super-high-speed

Amplifiers

(20 µs)

Water-resistant

Amplifiers

(IP66)

Standard

Amplifiers

Advanced

Amplifiers

Two-channel

Amplifiers

Color-sensing

Amplifiers

Selecting Fiber Amplifiers

All in One

For multifunctional capability: Select an Advanced Fiber Amplifier.

Simple For simple operation: Select a Simple Fiber Amplifier.

E3X-NA@

E3X-NA@F

E3X-NA@V

E3X-DA@-S

Standard models

E3X-DA@AN-S

Easy measurement control using analog output

E3X-DAC@-S

Color sensing models with white LEDs

Stable detection with resistance against workpiece

movement.

NEW

Digital display and direct setting

Reliable Bar display and adjuster setting

Intuitive

Fastest in class

E3X-MDA@

Save space with two Amplifiers packed

into a single case.

E3X-DA@TW-S

Range determination using twin outputs

E3X-DA@RM-S

Sensor control using external signal

E3X-DA@AT- S

Reliable operation in dust using

automatic threshold control.

World’s first

New concept

World’s first

Simple Fiber Amplifier

E3X-SD/-NA

The Standard for Fiber Amplifiers

with Simple Operation and High

Performance

■Operation so simple that essentially anyone can

use the amplifier right way.

■Immediately determine operation and amount of

light with a simple, bright display.

■General-purpose capabilities to simply handle a

broad range of applications.

Ordering Information

Amplifier Units

Digital Display and Direct Key Setting

Bar Display and Adjuster Setting

Item Appearance Connection

method

Ratings and

Specifications

Model

NPN output PNP output

Standard models

Pre-wired

---

E3X-SD11 E3X-SD41

Wire-saving

connector E3X-SD6 E3X-SD8

Item Appearance Connection

method

Ratings and

Specifications

Model

NPN output PNP output

Standard models

Pre-wired

---

E3X-NA11 E3X-NA41

Wire-saving

connector E3X-NA6 E3X-NA8

High-speed

detection models Pre-wired Response time: 20 µsE3X-NA11F E3X-NA41F

Water-resistant

models

Pre-wired

Degree of protection:

IP66

E3X-NA11V E3X-NA41V

Connector (M8) E3X-NA14V E3X-NA44V

E3X-SD/-NA

Amplifier Unit Connectors (Order Separately) Note: Stickers for Connectors are included as accessories.

Sensor I/O Connectors (Order Separately)

Accessories (Order Separately)

Item Appearance Cable length No. of conductors Model

Master Connector

2 m

3E3X-CN11

Slave Connector 1E3X-CN12

Size Cable specifications Appearance Cable type Model

M8 Standard cable

2 m

Four-

conductor

cable

XS3F-M421-402-A

5 m XS3F-M421-405-A

2 m XS3F-M422-402-A

5 m XS3F-M422-405-A

Combining Amplifier Units and

Connectors

Amplifier Units Applicable Connectors (Order Separately)

Type NPN PNP +Master Connector Slave Connector

(Basically, Amplifier Units and Connectors are sold

separately)

Refer to the following tables when placing an order.

Standard

models

E3X-SD6 E3X-SD8 E3X-CN11 (3-wire) E3X-CN12 (1-wire)

E3X-NA6 E3X-NA8

When Using 5 Amplifier Units

5 Amplifier Units +1 Master Connector + 4 Slave Connectors

Straight

connector

L-shaped

connector

Mounting Brackets

Appearance Applicable models Model Quantity

E3X-SD@

E3X-NA@

E3X-NA@F

E39-L143

E3X-NA@VE39-L148

End Plate

Appearance Model Quantity

PFP-M 1

E3X-SD/-NA

Ratings and Specifications

Amplifier Units

*1. For the E3X-NA, residual voltage is 1 V max.

*2. When there are 8 or more E3X-NA Amplifiers mounted side-by-side, the response time will be 350 µs max.

*3. The E3X-NA does not have output reverse polarity prevention.

*4. Water-resistant models and models with connectors have a dielectric strength of 500 VAC.

*5. Add 10 g for water-resistant models.

Amplifier Unit Connectors

Type

Digital display and direct key setting Bar display and adjuster setting

Standard models Standard models High-speed detection

models Water-resistant models

Model E3X-SD@E3X-NA@E3X-NA@FE3X-NA@V

Item

Light source (wavelength) Red LED (620 nm) Red LED (680 nm)

Power supply voltage 12 to 24 VDC ±10%, ripple (p-p): 10% max.

Current consumption 960 mW max. (Power supply: 24 V,

Current consumption: 40 mA max.) 35 mA max.

Control output

Open-collector output (NPN or PNP)

Load power supply: 26.4 V max., Load current: 50 mA max. (Residual voltage: 1.5 V max.) (*1)

Light-ON/Dark-ON mode selector

Response time Operate or reset: 200 µs max. (*2) Operate: 20 µs max.

Reset: 30 µs max.

Operate or reset: 200 µs

max. (*2)

Sensitivity adjustment UP/DOWN direct key setting, teaching 8-turn sensitivity adjuster (with indicator)

Protection circuits Power supply reverse polarity protection, output short-circuit protection, output reverse polarity protection (*3)

Timer function ON/OFF-delay timer: 10 ms (each fixed) OFF-delay timer: 40 ms (fixed)

Mutual interference

prevention Up to 5 Amplifiers (optically synchronized) None Up to 5 Amplifiers (optical-

ly synchronized)

Ambient illumination

Receiver side

Incandescent lamp: 10,000 lux max.

Sunlight: 20,000 lux max.

Ambient temperature

range

Operating: Groups of 1 to 3 Amplifiers: −25°C to 55°C

Groups of 4 to 11 Amplifiers: −25°C to 50°C

Groups of 12 to 16 Amplifiers: −25°C to 45°C

Storage: −30°C to 70°C (with no icing or condensation)

Ambient humidity range Operating and storage: 35% to 85% (with no condensation)

Insulation resistance 20 MΩ. min. (at 500 VDC)

Dielectric strength 1,000 VAC at 50/60 Hz for 1 minute (*4)

Vibration resistance Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hrs each in X, Y and Z directions

Shock resistance Destruction: 500 m/s2, for 3 times each in X, Y and Z directions

Degree of protection IEC 60529 IP50 (with Protective Cover attached)

IEC 60529 IP66

(with Protective Cover at-

tached)

Connection method Pre-wired (standard cable length: 2 m), or connector

Weight (packed state) Pre-wired model: Approx. 100 g, Model with connector: Approx. 55 g (*5)

Material Case Polybutylene terephthalate (PBT)

Cover Polycarbonate Polyethersulfone (PES)

Accessories Instruction manual

Item Model E3X-CN11 E3X-CN12

Rated current 2.5 A

Rated voltage 50 V

Contact resistance

20 mΩ max. (20 mVDC max., 100 mA max.)

(The above figure is for connection to the Amplifier Unit and the adjacent Connector. It does not include the conductor resistance of the

cable.)

Number of insertions Destruction: 50 times (for connection to the Amplifier Unit and the adjacent Connector)

Material Housing Polybutylene terephthalate (PBT)

Contact Phosphor bronze/gold-plated nickel

Weight (packed state) Approx. 55 g Approx. 25 g

E3X-SD/-NA

Fiber Unit Overview

New Head Shape

No snagging during maintenance.

Fiber flexibility prevents breaking.

L-shaped Attachment

Feature

10 mm*

Through-beam model,

M4 screw

E32-T11N

Reflective model,

M6 screw

E32-D11N

280 mm

90 mm

8 mm*

*For M6 models.

Convenient design

accommodates two wrench sizes.

Allows quick tightening.

No snagging, no breaking:

Right-angle (L-shaped) Models

Reflective Fiber Units

Size: 15 × 10 × 3 mm

Flat and flexible fiber models are easy to mount

and will not break.

20 mm

Flat View

E32-D15ZR

Flexible fiberConventional fiber

Cladding

Cores

No Breaking

Feature

A large number of ultrafine cores are all surrounded by cladding. As

a result, the fiber is flexible and can be bent without significantly

reducing the light intensity. This helps solve problems, such as

fiber being broken by getting caught on other objects.

Through-beam Fiber Units

Size: 15 × 8 × 3 mm

280 mm

110 mm 110 mm

Top View

E32-T15XR

Side View

E32-T15YR

Flat View

E32-T15ZR

E3X-SD/-NA

Sensing Distance

Through-beam Models (Unit: mm)

Model E3X-SD@

E3X-NA@E3X-NA@F

Type Standard

models

High-speed detection

models

Standard

models

Flexible

(new standard)

E32-T11R/E32-T12R/E32-T15XR/E32-TC200BR (B4R) 280 80

E32-T14LR/E32-T15YR/E32-T15ZR 110 33

E32-T21R/E32-T22R/E32-T222R/E32-T25XR/

E32-TC200FR (F4R) 60 18

E32-T24R/E32-T25YR/E32-T25ZR 30 9

Standard

E32-TC200/E32-T12/E32-T15X/E32-TC200B (B4) 400 120

E32-T14L/E32-T15Y/E32-T15Z 240 70

E32-TC200A 360 100

E32-TC200E/E32-T22/E32-T222/E32-T25X/E32-TC200F (F4) 100 30

E32-T24/E32-T25Y/E32-T25Z 90 27

Break resistant

E32-T11/E32-T12B/E32-T15XB 360 100

E32-T21/E32-T221B/E32-T22B 100 30

E32-T25XB 75 20

Fluorine coating E32-T11U 360 100

Special-

beam

models

Long distance,

high power

E32-T17L 14000 4200

E32-TC200 + E39-F1 3000 900

E32-T11R + E39-F1 2100 630

E32-T11 + E39-F1 2000 600

E32-T14 1800 540

E32-T11L/E32-T12L 700 210

E32-T11L + E39-F2 500 150

E32-T11R + E39-F2 220 65

E32-T11 + E39-F2 360 100

E32-T21L/E32-T22L 200 60

Ultracompact,

ultrafine sleeve

E32-T223R 60 18

E32-T33-S5 20 6

E32-T333-S5 5 1.5

E32-T334-S5 2.5 0.8

Fine beam

(narrow vision field)

E32-T22S 1000 300

E32-T24S 700 210

Area sensing

E32-T16PR 450 130

E32-T16P 600 180

E32-T16JR 390 110

E32-T16J 520 150

E32-T16WR 690 200

E32-T16W 920 270

E32-T16 1500 450

E32-M21 300 90

Environment

resistive

models

Heat resistant

E32-T51 400 120

E32-T54 130 35

E32-T81R-S 180 50

E32-T61-S + E39-F2 390 130

E32-T61-S + E39-F1 3000 900

E32-T84S-S 700 210

E32-T61-S 300 90

Chemical

resistant

E32-T11F 1050 380

E32-T12F 1600 480

E32-T14F 200 60

E32-T51F 700 200

E32-T81F-S 350 100

Vacuum

resistant

E32-T51V 100 ---

E32-T51V + E39-F1V 600 ---

E32-T54V 65 ---

E32-T54V + E39-F1V 390 ---

E32-T84SV 250 ---

For information on Fiber Units, refer to the E32 Series Fiber Sensor Best Selection (Cat. No. E354).

E3X-SD/-NA

Reflective Models (Unit: mm)

Model E3X-SD@

E3X-NA@E3X-NA@F

Type Standard

models

High-speed detection

models

Standard

models

Flexible

(new standard)

E32-D11R/E32-D12R/E32-D15XR/E32-DC200BR (B4R) 90 30

E32-D14LR 16 5

E32-D15YR/E32-D15ZR 20 5

E32-D211R/E32-D21R/E32-D22R/E32-D25XR/

E32-DC200FR (F4R) 15 5

E32-D24R 7 2.3

E32-D25YR/E32-D25ZR 4 1.2

Standard

E32-DC200/E32-D15X/E32-DC200B (B4) 150 50

E32-D12 120 40

E32-D14L 40 13

E32-D15Y/E32-D15Z 50 15

E32-D211/E32-DC200E/E32-D22/E32-D25X/

E32-DC200F (F4) 36 12

E32-D24 15 5

E32-D25Y/E32-D25Z 10 3.3

Break resistant

E32-D11/E32-D15XB 90 30

E32-D21B/E32-D221B 35 10

E32-D21/E32-D22B 15 5

E32-D25XB 25 8

Fluorine coating E32-D11U 90 30

Special-

beam

models

Long distance,

high power

E32-D16 40 to 400 55 to 70

E32-D11L 200 65

E32-D21L/E32-D22L 50 17

Ultracompact,

ultrafine sleeve

E32-D33 10 3.3

E32-D331 1.5 0.5

Coaxial, small spot

E32-CC200R 75 25

E32-CC200 150 50

E32-D32L 80 25

E32-C31/E32-D32 40 13

E32-C42 + E39-F3A Spot diameter of 0.1 to 0.6 mm at

6 to 15 mm.

E32-D32 + E39-F3A Spot diameter of 0.5 to 1 mm at

6 to 15 mm.

E32-C41 + E39-F3A-5 Spot diameter of 0.1 mm at 7 mm.

E32-C31 + E39-F3A-5 Spot diameter of 0.5 mm at 7 mm.

E32-C41 + E39-F3B Spot diameter of 0.2 mm at 17 mm.

E32-C31 + E39-F3B Spot diameter of 0.5 mm at 17 mm.

E32-C31 + E39-F3C Spot diameter of 4 mm max. at

0 to 20 mm.

Area sensing E32-D36P1 75 25

Retro-reflective E32-R21 + E39-R3 (provided) 10 to 250

E32-R16 + E39-R1 (provided) 150 to 1500 150 to 1000

Convergent-

reflective

E32-L25/E32-L25A 3.3

E32-L24S 0 to 4

E32-L24L 2 to 6 (center 4)

E32-L25L 5.4 to 9 (center 7.2)

E32-L86 4 to 10

E32-L16 0 to 15 0 to 13

Environ-

ment

resistive

models

Heat resistant

E32-D51 120 40

E32-D81R/E32-D61 45 15

E32-D73 30 10

Chemical resistant E32-D12F 50 16

E32-D14F 20 6.5

For information on Fiber Units, refer to the E32 Series Fiber Sensor Best Selection (Cat. No. E354).

E3X-SD/-NA

I/O Circuit Diagrams

Note: Timing Charts for Timer Settings (T: Set Time)

Plug (Sensor I/O Connector)

Output

form Model

Output

transistor

operation mode

Timing charts Operation

selector Output circuit

NPN

Output

E3X-SD11

E3X-SD6

E3X-NA11

E3X-NA6

E3X-NA11F

E3X-NA11V

E3X-NA14V

Light-ON LIGHT ON

(L-ON)

Dark-ON DARK ON

(D-ON)

PNP

Output

E3X-SD41

E3X-SD8

E3X-NA41

E3X-NA8

E3X-NA41F

E3X-NA41V

E3X-NA44V

Light-ON LIGHT ON

(L-ON)

Dark-ON DARK ON

(D-ON)

ON delay OFF delay

Incident light

No incident light

OFF

Operate

Reset

Operation

indicator

(orange)

(Between brown and black leads)

Output

transistor

Load

(relay)

Black

Brown

Blue

Control output

Operation indicator

(orange)

Photo-

electric

Sensor

main

circuit

Load

12 to

24 VDC

• M8 Connector Pin Arrangement

Note: Pin 2 is not used.

*Not present on the E3X-NA.

Incident light

No incident light

OFF

Operate

Reset

Operation

indicator

(orange)

(Between brown and black leads)

Output

transistor

Load

(relay)

Incident light

No incident light

OFF

Operate

Reset

Operation

indicator

(orange)

(Between blue and black leads)

Output

transistor

Load

(relay)

*Not present on the E3X-NA.

Black

Brown

Blue

Control output

Operation

indicator

(orange) Photo-

electric

Sensor

main

circuit Load

12 to

24 VDC

• M8 Connector Pin Arrangement

Note: Pin 2 is not used.

Incident light

No incident light

OFF

Operate

Reset

Operation

indicator

(orange)

(Between blue and black leads)

Output

transistor

Load

(relay)

Incident light

No incident light

OFF

L-ON

D-ON

Incident light

No incident light

OFF

L-ON

D-ON

Note: Pin 2 is not used.

Classification Wire color Connection pin Application

Brown 1 Power supply (+V)

White 2 ---

Blue 3 Power supply (0 V)

Black 4 Output

Brown

White

Blue

Black

Wire color

Terminal number

XS3F-M421-402-A

XS3F-M421-405-A

XS3F-M422-402-A

XS3F-M422-405-A

E3X-SD/-NA

Nomenclature

Safety Precautions

This product is not designed or rated for

ensuring safety of persons either directly or

indirectly.

Do not use it for such purposes.

Do not exceed the rated voltage.

Excess voltage may result in malfunction or

fire.

Do not use an AC power supply.

Using an AC power supply may result in

rupturing.

High-temperature environments may result in

burn injury.

The following precautions must be observed to ensure safety.

1. Do not use the product in locations where flammable or

explosive gas is present.

2. Do not use the product in locations subject to splashing

water, oil, or chemicals, or in locations subject to steam.

3. Do not attempt to disassemble, repair, or modify the

product.

4. Do not apply voltage or current in excess of the rated

ranges.

5. Do not use the product in atmospheres or environments

that exceed product ratings.

6. Do not wire the product incorrectly, such as using incorrect

power supply polarity.

7. Connect the load properly.

8. Do not short-circuit both ends of the load.

9. Do not use the product if the case is damaged.

10. When disposing of the product, dispose of it as industrial

waste.

11. Do not use the product in locations subject to direct

sunlight.

12. The surface temperature of the product may rise as a

result of the ambient temperature, power supply, or other

usage conditions. Use caution when performing

maintenance and washing. Failure to do so may result in

burn injury.

Incident level

indicators

Lock lever

Operation Keys

Sensitivity adjustment

(UP/DOWN or teaching)

TEACH/RUN Mode Selector

Used to select TEACH or RUN mode.

Operation Indicator

Operation Selector

Use to switch between

Light-ON and Dark-ON

Timer switch

OFF/D: OFF-delay timer

ON/D: ON-delay timer

OFF: Timer function is OFF.

Amplifier Units

E3X-SD@E3X-NA

Incident level indicators

Lock lever

Sensitivity indicator

8-turn sensitivity adjuster

Operation Indicator

Operation Selector

Use to switch between

Light-ON and Dark-ON

Timer switch

ON: Timer function is ON.

OFF: Timer function is OFF.

WARNING

Caution

Precautions for Safe Use

E3X-SD/-NA

Do not use the product in atmospheres or environments that

exceed product ratings.

Amplifier Units

●Designing

Communications Hole

The hole on the side of the Amplifier Unit is a communications

hole for preventing mutual interference when Amplifier Units

are mounted side-by-side. The E3X-MC11 Mobile Console

(order separately) cannot be used.

If an excessive amount of light is received via the Sensor, the

mutual interference prevention function may not work. In this

case, make the appropriate adjustments using the sensitivity

adjuster.

The mutual interference prevention function will not operate

when the E3X-SD/NA is used side-by-side with E3X-DA-N

models.

●Mounting

DIN Track Mounting/Removal

Mounting Amplifier Units

1. Mount the Amplifier Units one at a time onto the DIN track.

2. Slide the Amplifier Units together, line up the clips, and

press the Amplifier Units together until they click into place.

Removing Amplifier Units

Slide Amplifier Units away from each other, and remove from

the DIN track one at a time. (Do not attempt to remove

Amplifier Units from the DIN track without separating them

first.)

Fiber Connection and Disconnection

The E3X Amplifier Unit has a lock lever. Connect or

disconnect the fibers to or from the E3X Amplifier Unit using

the following procedures:

1. Connection

Open the Protective Cover, insert the fibers according to the

fiber insertion marks on the side of the Amplifier Unit, and

lower the lock lever.

2. Disconnection

Remove the Protective Cover and raise the lock lever to pull

out the fiber.

Note:To maintain the fiber properties, confirm that the lock is

released before removing the fiber.

3. Precautions for Fiber Connection/Disconnection

Be sure to lock or unlock the lock lever within an ambient

temperature range between −10°C and 40°C.

●Operating Environment

Ambient Conditions

If dust or dirt adhere to the hole for optical communications, it

may prevent normal communications. Be sure to remove any

dust or dirt before using the Units.

●Other

Protective Cover

Be sure to mount the Protective Cover before use.

Precautions for Correct Use

Note 1. The specifications for ambient temperature will vary according to the

number of Amplifier Units used together. For details, refer to Ratings

and Specifications.

2. Always turn OFF the power supply before mounting or removing

Amplifier Units.

Click into

place

Clip

Lock lever

Fiber Fiber insertion mark 10.7 mm

Insertion position

Locked Unlocked

Protective Cover

E3X-SD/-NA

Amplifier Units with Connectors

●Mounting

Mounting Connectors

1. Insert the Master or Slave Connector into the Amplifier Unit

until it clicks into place.

2. Join Amplifier Units together as required after all the Master

and Slave Connectors have been inserted.

3. Attach the stickers (provided as accessories) to the sides of

Master and Slave Connectors that are not connected to

other Connectors.

Note: Attach the stickers to the sides with grooves.

Removing Connectors

1. Slide the slave Amplifier Unit for which the Connector is to

be removed away from the rest of the group.

2. After the Amplifier Unit has been separated, press down on

the lever on the Connector and remove it. (Do not attempt

to remove Connectors without separating them from other

Amplifier Units first.)

Mounting End Plate (PFP-M)

Depending on how it is mounted, an Amplifier Unit may move

during operation. In this case, use an End Plate.

Before mounting an End Plate, remove the clip from the

master Amplifier Unit using a nipper or similar tool.

The clip can also be removed using the following mechanism,

which is incorporated in the construction of the section

underneath the clip.

1. Insert the clip to be removed into the slit underneath the clip

on another Amplifier Unit.

2. Remove the clip by rotating the Amplifier Unit.

Pull Strengths for Connectors (Including Cables)

E3X-CN11: 30 N max.

E3X-CN12: 12 N max.

Insert

Sticker

Remove

Lever

Press down

Clip

Rotate

E3X-SD/-NA

Dimensions (Unit: mm)

Amplifier Units

10.7

364.3

38.6

31.5

9.9

5.3

3.4

22.4

4.4

4.1

13 34.8

2.4

22.4 16

10.75 16

4.4

3.4

Two,

2.4 dia.

Two, 3.2-dia. holes Mounting bracket (E39-L143) (Order separately)

Stainless steel (SUS304)

A *1

Mounting Holes

Two, M3

Operation indicator

*1. The mounting bracket can also be used on

side A.

*2. There is no hole for E3X-NA@F models.

4-dia. vinyl-insulated round cable with

3 conductors* (Conductor cross section: 0.2 mm2;

Insulator diameter: 1.1 mm),

Standard length: 2 m.

Hole for optical communications *2

Amplifier Units with Cables

E3X-SD11

E3X-SD41

E3X-NA11

E3X-NA11F

E3X-NA41

E3X-NA41F

With Mounting Bracket Attached

Amplifier Units with

onnectors

E3X-SD6

E3X-SD8

E3X-NA6

E3X-NA8

Dimensions with Master Connector Connected Dimensions with Slave Connector Connected

10 64.33

10.7

9.9

3.4

38.6

3.95.1

1.7

4.2

6.2 1.7

36.7

31.5

5.5

1.8

Two, 2.4 dia.

Operation indicator

Hole for optical communications

(for preventing mutual interference)

64.3

67.5

1.5

31.5

1.8 5.1 3.9 34.8

12.95

E3X-CN12: 2.6 dia.

11.55

17.45

1.5

31.5

1.8 5.1 3.9

12.95

64.3

67.5

E3X-CN11:

4.0 dia.

E3X-SD/-NA

9.2

28.65

25.95

10.7

4.3

9.9

3.43.9

23.9

14.4

11.5 67.2

23.9 6.6

11.2

2.8

5.4

3.4

6.9

81.5

A *1

Two,

2.4 dia.

Mounting bracket (E39-L148) (Order separately)

Stainless steel (SUS304)

Two, M3

Mounting Holes

Operation indicator

Incident level indicators

Hole for

optical

communi-

cations

*1. The mounting bracket can also be used on side A.

*2. 4-dia. vinyl-insulated round cable with 3 conductors

(Conductor cross section: 0.45 mm2, Insulator diameter:

1.1 mm), Standard length: 2 m.

Amplifier Units with Cables,

Water-resistant Models

E3X-NA11V

E3X-NA41V

With Mounting Bracket Attached

10.7

4.3

9.9

3.43.9

23.9

14.4

11.5 67.2

23.9

11.2

2.8 M8

5.4

3.4

9.2

28.65

25.95

81.5

Two,

2.4 dia.

Two, M3

Operation indicator

Incident level indicators

Mounting bracket (E39-L148) (Order separately)

Stainless steel (SUS304)

Mounting Holes

6.9

* The mounting bracket can also be

used on this side A.

Hole for

optical

communi-

cations

Ampli

ier Units with

onnectors,

Water-resistant Models

E3X-NA14V

E3X-NA44V

With Mounting Bracket Attached

E3X-SD/-NA

Amplifier Unit Connectors

Accessories (Order Separately)

For information on Fiber Units, refer to the E32 Series Fiber Sensor Best Selection (Cat. No. E354).

Master Connector

E3X-CN11

14.4

2.6

2.9

0.8 8.4

6.8

10.7

50+5

30±2

4 dia.

10±2

15.1

2,000+50

*E3X-CN11: 2.6-dia. vinyl-insulated round cable with 3 conductors (Conductor cross section: 0.2 mm2, Insulator diameter: 1.1 mm)

Slave Connector

E3X-CN12

14.4

2.6

2.9

0.8 8.4

6.8

10.7

2,000+50

50+5

30±2

E3X-CN12: 2.6 dia.

E3X-CN22: 4 dia.

10±2

15.1

*E3X-CN12: 2.6-dia. vinyl-insulated round cable with 1 conductor (Conductor cross section: 0.2 mm2, Insulator diameter: 1.1 mm)

Mounting Brackets

E39-L143

Four, R1.7

3.4

3163

10 max. 710.3

7.3

5.3

(10.3) 2.5

34.8

26.8

Two, 3.2 dia.

3.4

Two, M 3

16±0.1

Mounting Holes

Material: Stainless steel

(SUS304)

End Plates

PFP-M

11.5

M4 × 8

panhead screw

M4 spring washer

4.8

1.3

1.8

6.2 10

35.5

35.3

E3X-SD/-NA

Operating Procedure

E3X-SD@

A 7-segment display showing excess gain is provided in

addition to the orange operation indicator.

Use these when adjusting the light axis and setting the

sensitivity at setup.

The sensitivity can be set with the UP and DOWN Keys similar

to using an adjuster knob. The sensitivity can also be easily

set by using the following three teaching functions.

The sensitivity can be set to the maximum. This is the optimal

setting for resistance against the effects of dust.

Two points (one with the workpiece and the other without) are

detected, and the operating level is set to the midpoint.

Changes within a time are detected, and the operating level is

set to the midpoint between the maximum and the minimum

values of the changes. This setting is optimal for when the

workpieces cannot be stopped.

E3X-NA@

A bar display (with four green and one red) showing excess

gain is provided in addition to the orange operation indicator.

Use these when adjusting the light axis and setting the

sensitivity at setup.

Display/indicator status (for L/ON) Excess gain Description

999%

(10 times)

110% min.

Stable incident

light

100%

90% to 110%

Unstable

incident light or

Unstable

interrupted light

90% max.

Stable

interrupted light

Operation description Switch/Key Display

Set the TEACH/RUN selector

switch to TEACH.

Press the UP Key for 3 s min.

Set the TEACH/RUN selector

switch to RUN (start of mea-

surement).

Operation description Switch/Key Display

Set the TEACH/RUN selector

switch to TEACH.

Press the UP Key with the

workpiece present.

Press the UP Key with the

workpiece not present.

Set the TEACH/RUN selector

switch to RUN (start of mea-

surement).

Operation description Switch/Key Display

Set the TEACH/RUN selector

switch to TEACH.

Press the UP Key.

Displays1

Operation indicator

Excess gain display

Sensitivity Setting2

2-1. Maximum Sensitivity Setting

RUN

TEACH

RUN

TEACH

2-2. Teaching with/without a Workpiece

RUN

TEACH

RUN

TEACH

2-3. Automatic Teaching

RUN

TEACH

Hold down the UP Key during

detection. Let the workpiece

pass while the key is held down.

Set the TEACH/RUN selector

switch to RUN (start of mea-

surement).

Display/indicator status (for L/ON) Excess gain

level Description

Approx.

120% min.

Stable incident

light

Approx.

110% to 120%

Approx.

90% to 110%

Unstable

incident light or

Unstable

interrupted light

Approx.

80% to 90%

Stable

interrupted light

Approx.

80% max.

Operation description Switch/Key Display

RUN

TEACH

Displays1

Operation indicator

Excess gain level display

E3X-SD/-NA

READ AND UNDERSTAND THIS DOCUMENT

Please read and understand this document before using the products. Please consult your OMRON representative if you have any questions or

comments.

WARRANTY

OMRON’s exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if

specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,

MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT

THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR

INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR

COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY,

NEGLIGENCE, OR STRICT LIABILITY.

In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS

OMRON’S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND

NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

SUITABILITY FOR USE

THE PRODUCTS CONTAINED IN THIS DOCUMENT ARE NOT SAFETY RATED. THEY ARE NOT DESIGNED OR RATED FOR ENSURING

SAFETY OF PERSONS, AND SHOULD NOT BE RELIED UPON AS A SAFETY COMPONENT OR PROTECTIVE DEVICE FOR SUCH

PURPOSES. Please refer to separate catalogs for OMRON's safety rated products.

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the

customer’s application or use of the product.

At the customer’s request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply

to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end

product, machine, system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all

possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document.

• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,

safety equipment, and installations subject to separate industry or government regulations.

• Systems, machines, and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT

THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY RATED

AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PERFORMANCE DATA

Performance data given in this document is provided as a guide for the user in determining suitability and does not constitute a warranty. It may

represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject

to the OMRON Warranty and Limitations of Liability.

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons.

It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the product may be changed without any notice. When in doubt, special model numbers may be assigned to fix

or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual

specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,

typographical, or proofreading errors, or omissions.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user’s programming of a programmable product, or any consequence thereof.

This document shall not be copied for sales or promotions without permission.

This document is protected by copyright and is intended solely for use in conjunction with the product. Please notify us before copying or

reproducing this document in any manner, for any other purpose. If copying or transmitting this document to another, please copy or transmit it in

its entirety.

Authorized Distributor:

Note: Specifications subject to change without notice.

Regional Headquarters

Cat. No. E388-E1-01

1007

OMRON Corporation

Industrial Automation Company

Sensing Devices Division H.Q.

Industrial Sensors Division

Shiokoji Horikawa, Shimogyo-ku,

Kyoto, 600-8530 Japan

Tel: (81)75-344-7022/Fax: (81)75-344-7107

OMRON EUROPE B.V.

Sensor Business Unit,

Carl-Benz-Str. 4 D-71154 Nufringen,

Germany

Tel: (49) 7032-811-0/Fax: (49) 7032-811-199

OMRON ELECTRONICS LLC

One Commerce Drive Schaumburg,

IL 60173-5302 U.S.A.

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark, Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

83 Clemenceau Avenue,

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

Pu Dong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

This document provides information mainly for selecting suitable models. Please read the Instruction sheet carefully for information that the user

must understand and accept before purchase, including information on warranty, limitations of liability, and precautions.

2007.12

OMRON Corporation

Industrial Automation Company

In the interest of product improvement, specifications are subject to change without notice.

Cat. No. E388-E1-01