Photologic(R) Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series Features: * * * * * Choice of logic and output driver circuits Choice of aperture size, covered or open Wire or PCB leads Choice of mounting features Direct TTL, LSTTL, CMOS Interface Description: The OPB960/ 970/ 980/ 990 series of non-contact Photologic(R) slotted optical switches provides flexibility in meeting application specific requirements for the design engineer. Building from a standard housing with a 0.125" (3.18mm) wide slot, the user can specify output logic state, output driver circuit, aperture width, aperture surface and mounting tab locations. Furthermore, an option of wire or PCB leads allows electrical interface flexibility. The device body is an opaque plastic which minimizes sensitivity to both visible and near-infrared external light sources which may impact operation. Aperture width choices provide different optical resolution for motion sensing. A covered aperture provides dust protection, while an open aperture provides maximum protection against external light sources. Electrical operation is over a wide supply voltage range. LED emissions are near-infrared (850--940nm). Detector digital output logic choices of buffer or inverter with totem-pole or open-collector driver circuit simplify interface for various electrical requirements. Custom electrical, wire and cabling services are available. Contact your local representative or OPTEK for more information. Compliant to EU RoHS Directive 2002/95/EC . For more information see Application notes 201, 213 Applications: * Speed and direction indication * Rotary encoders * Mechanical switch replacement * Mechanical limit indication * Printers - Top of form, End of travel, Home position. * Sliding Door Automotive and Lift gate applications Part Number Guide OPB 9XX X XX X OPTEK Assembly Z = Wires only, None for PCB leads (R) Photologic Sensor Family Aperture Width Guide Options: 55, 51, 11 ( See Aperture Width Guide ) Slot Aperture Surface and Lead Options: 6 -- Covered (apertures not visible), PCB leads 7 -- Open (apertures visible), PCB leads 8 -- Covered (apertures not visible), Wires 9 -- Open (apertures visible), Wires Mounting Tab Location: L -- Emitter N -- None P -- Sensor T -- Both (two mounting tabs) Logic and Output Driver Types: 0 -- Buffer Totem-Pole 1 -- Buffer Open-Collector 2 -- Inverter Totem-Pole 3 -- Inverter Open-Collector RoHS Logic Type Input LED Output Logic State Buffer OFF LOW = 0 Inverter OFF HIGH = 1 OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue C.1 1/10 Page 1 of 6 (R) Photologic Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series PACKAGE OUTLINE for OPB960 and OPB970 Series TABLE 1 APERTURE WIDTH GUIDE Lead No. Function 1 CODE LED SENSOR Anode 55 .050" [1.27mm] .050" [1.27mm] 2 Cathode 51 .050" [1.27mm] .010" [0.25mm] 3 Vcc 11 .010" [0.25mm] .010" [0.25mm] 4 Output 5 Ground Notes: (1) (2) (3) (4) (5) (6) Lengths are .050" [1.27mm] RMA flux recommended. Duration can be extended to 10 seconds max. Feature controlled at body. Highly activated water soluble fluxes may attack plastic. Recommend trial to verify application. Maximum lead soldering temperature [1.6mm from case for 5 seconds with soldering iron] 260 C. Cathode lead may be shorter. Part number marking may be on any side. OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. Issue C.1 1/10 Page 2 of 6 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Photologic(R) Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series PACKAGE OUTLINE for OPB980 and OPB990 Series TABLE 2 APERTURE WIDTH GUIDE Wire Color Function Red CODE LED SENSOR Anode 55 .050" [1.27mm] .050" [1.27mm] Black Cathode 51 .050" [1.27mm] .010" [0.25mm] White Vcc 11 .010" [0.25mm] .010" [0.25mm] Blue Output Green Ground Notes: (7) (8) (9) (10) Lengths are .050" [1.27mm] Wire is 26AWG, UL Rated PVC insulation. Ideal torque for bolt or screw 0,45 to 0,68 Nm ( 4 to 6 Lb-in ). When using a thread lock compound, ND Industries "ND Vibra-Tite(R) Formula 3" will avoid stress cracking plastic. Plastic is soluble in chlorinated hydrocarbons and ketones. Methanol or isopropanol are recommended as cleaning agents. OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue C.1 1/10 Page 3 of 6 (R) Photologic Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series Absolute Maximum Ratings Storage Temperature Range -40C to +85 C Operating Temperature Range -40C to +70 C Input Diode (E) 100 mW ( 11) Input Diode Power Dissipation Input Diode Forward D.C. Current, TA = 25C 40 mA( 14) Input Diode Reverse D.C. Voltage, TA = 25C 2V Sensor (S) 18 V ( 13) Supply Voltage (VCC to Ground) (R) 200 mW ( 12) Output Photologic Power Dissipation Voltage at Output Lead (Open-Collector Output), TA = 25C 35V Short Circuit Output Current to Ground (IOS ) 1 sec Max. 30 mA Notes: (11) Derate linearly 2.22 mW / C above 25 C. (12) Derate linearly 4.44 mW / C above 25 C. (13) Prior to 2004 Vcc was limited to 5.5V maximum. (14) Do not connect input diode directly to a voltage source without an external current limiting resistor. Block Diagram Buffer Totem-Pole OPB960/ OPB970/ OPB980/ OPB990 Inverter Totem-Pole OPB962/ OPB972/ OPB982/ OPB992 Buffer Open-Collector OPB961/ OPB971/ OPB981/ OPB991 Inverter Open-Collector OPB963/ OPB973/ OPB983/ OPB993 OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. Issue C.1 1/10 Page 4 of 6 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Photologic(R) Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series Electrical Characteristics (TA = -40 C to +70 C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP140 / OP240 LED for additional information) VF Forward Voltage - - 1.70 V IF = 20 mA, TA = 25 C IR Reverse Current - - 100 A VR = 2.0 V, TA = 25 C 4.5 - 16 V - - 12 mA Coupled (See OPL560 Detector for additional information) VCC Operating D.C. Supply Voltage ICC Supply Current VOL Low Level Output Voltage: Buffer Totem-Pole OPB960,OPB970 OPB980,OPB990 Buffer Open-Collector OPB961,OPB971 OPB981,OPB991 Inverter Totem-Pole OPB962,OPB972 OPB982,OPB992 VCC = 4.5V, IOL = 12.8mA IF = 0 mA (14) - - 0.4 V VCC = 4.5V, IOL = 12.8mA IF = 15 mA Inverter Open-Collector OPB963,OPB973 OPB983,OPB993 VOH High Level Output Voltage: Buffer Totem-Pole Inverter Totem-Pole IOH OPB960,OPB970 OPB980,OPB990 VCC -2.1 - - V OPB961,OPB971 OPB981,OPB991 - - 100 A LED Positive-Going Threshold Current(16) - - 15 mA - 1.5 - - Output Rise Time, Output Fall Time - 70 - ns Propagation Delay Time Low to High, High to Low - 5.0 - s IF(+) / IF(-) Hysteresis Ratio tR, tF tPLH, tPHL VCC = 4.5V to 16V, VOH = 30V IF = 15 mA VCC = 4.5V to 16V, VOH = 30V IF = 0 mA (14) Inverter Open-Collector OPB963,OPB973 OPB981,OPB991 IF(+) VCC = 4.5V to 16V, IOH = -800A IF = 15 mA VCC = 4.5V to 16V, IOH = -800A IF = 0 mA (14) OPB962,OPB972 OPB982,OPB992 High Level Output Current: Buffer Open-Collector VCC = 4.5V to 16V VCC = 5.0V, TA = 25 C VCC = 5.0V VCC = 5.0V, IF peak= 15 mA, TA = 25 C 100 kHz square wave, C = 10pF max. RL = 360 to GND (Totem-Pole) RL = 1K pull-up (Open-Collector) Notes: 14) Normal application would be with light source blocked, simulated by IF = 0 mA. 15) All parameters are tested using pulse techniques. 16) An increasing current applied to the LED which causes the output logic state to change. For proper application IF(+), LED current, should be more than the stated maximum. OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue C.1 1/10 Page 5 of 6 (R) Photologic Slotted Optical Switch OPB960, OPB970, OPB980, OPB990 Series Logic Output vs Left to Right Bocking Distance (X-Axis Blocked) 5.0 VCC = 5 Volts IF = 20m A Buffer Totem -Pole Logic Output (V) 4.0 Aperture Width 11 3.0 Aperture Width 51 Aperture Width 55 2.0 1.0 0.0 0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.200 0.225 0.250 Distance (inches) Logic Output vs Top to Bottom Bocking Distance (Y-Axis Blocked) 5.0 VCC = 5 Volts IF = 20m A Buffer Totem -Pole Logic Output (V) 4.0 3.0 2.0 1.0 0.0 0.000 0.025 0.050 0.075 0.100 0.125 0.150 Distance (inches) 0.175 0.200 0.225 0.250 OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible. Issue C.1 1/10 Page 6 of 6 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com