OPB980T51Z - OPTEK TECHNOLOGY - Datasheet.Directory

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 1 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Features:

• Choice of logic and output driver circuits

• Choice of aperture size, covered or open

• Wire or PCB leads

• Choice of mounting features

• Direct TTL, LSTTL, CMOS Interface

Description:

The OPB960/ 970/ 980/ 990 series of non-contact Photologic® slotted optical switches provides flexibility in meeting application

specific requirements for the design engineer.

Building from a standard housing with a 0.125” (3.18mm) wide slot, the user can specify output logic state, output driver circuit,

aperture width, aperture surface and mounting tab locations. Furthermore, an option of wire or PCB leads allows electrical

interface flexibility.

The device body is an opaque plastic which minimizes sensitivity to both visible and near-infrared external light sources which

may impact operation. Aperture width choices provide different optical resolution for motion sensing. A covered aperture

provides dust protection, while an open aperture provides maximum protection against external light sources.

Electrical operation is over a wide supply voltage range. LED emissions are near-infrared (850—940nm).

Detector digital output logic choices of buffer or inverter with totem-pole or open-collector driver circuit simplify interface for

various electrical requirements.

Custom electrical, wire and cabling services are available.

Contact your local representative or OPTEK for more information. Compliant to EU RoHS Directive 2002/95/EC .

RoHS

OPTEK Assembly

Photologic® Sensor Family

Slot Aperture Surface and Lead Options:

6 — Covered (apertures not visible), PCB leads

7 — Open (apertures visible), PCB leads

8 — Covered (apertures not visible), Wires

9 — Open (apertures visible), Wires

Logic and Output Driver Types:

0 — Buffer Totem-Pole

1 — Buffer Open-Collector

2 — Inverter Totem-Pole

3 — Inverter Open-Collector

Z = Wires only, None for PCB leads

Aperture Width Guide Opti ons :

55, 51, 11 ( See Aperture Width Guide )

Mounting Tab Location:

L — Emitter

N — None

P — Sensor

T — Both (two mounting tabs)

Part Number Guide

OPB 9XX X XX X

Logic Type Input

LED Output

Logic State

Buffer OFF LOW = 0

Inverter OFF HIGH = 1

Applications:

• Speed and direction indication

• Rotary encoders

• Mechanical switch replacement

• Mechanical limit indication

• Printers - Top of form, End of travel, Home position.

• Sliding Door Automotive and Lift gate applications

For more information see Application notes 201, 213

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 2 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Lead No. Function

1 Anode

2 Cathode

3 Vcc

4 Output

5 Ground

TABLE 1

PACKAGE OUTLINE for OPB960 and OPB970 Seri es

APERTURE WIDTH GUIDE

CODE LED SENSOR

55 .050” [1.27mm] .050” [1.27mm]

51 .050” [1.27mm] .010” [0.25mm]

11 .010” [0.25mm] .010” [0.25mm]

Lengths are .050” [1.27mm]

Notes:

(1) RMA flux recommended. Duration can be extended to 10 seconds max.

(2) Feature controlled at body.

(3) Highly activated water soluble fluxes may attack plastic. Recommend trial to verify application.

(4) Maximum lead soldering temperature [1.6mm from case for 5 seconds with soldering iron] 260° C.

(5) Cathode lead may be shorter.

(6) Part number marking may be on any side.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 3 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Wire Color Function

Red Anode

Black Cathode

White Vcc

Blue Output

Green Ground

TABLE 2

Notes:

(7) Wire is 26AWG, UL Rated PVC insulation.

(8) Ideal torque for bolt or screw 0,45 to 0,68 Nm ( 4 to 6 Lb-in ).

(9) When using a thread lock compound, ND Industries ”ND Vibra-Tite® Formula 3” will avoid stress cracking plastic.

(10) Plastic is soluble in chlorinated hydrocarbons and ketones. Methanol or isopropanol are recommended as cleaning agents.

PACKAGE OUTLINE for OPB980 and OPB990 Seri es

APERTURE WIDTH GUIDE

CODE LED SENSOR

55 .050” [1.27mm] .050” [1.27mm]

51 .050” [1.27mm] .010” [0.25mm]

11 .010” [0.25mm] .010” [0.25mm]

Lengths are .050” [1.27mm]

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 4 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Absolute Maximum Ratings

Storage Temperature Range -40°C to +85° C

Operating Temperature Range -40°C to +70° C

Input Diode (E)

Input Diode Power Dissipation 100 mW ( 11)

Input Diode Forward D.C. Current, TA = 25°C 40 mA( 14)

Input Diode Reverse D.C. Voltage, TA = 25°C 2 V

Sensor (S)

Supply Voltage (VCC to Ground) 18 V ( 13)

Output Photologic® Power Dissipation 200 mW ( 12)

Voltage at Output Lead (Open-Collector Output), TA = 25°C 35V

Short Circuit Output Current to Ground (IOS ) 1 sec Max. 30 mA

Notes:

(11) Derate linearly 2.22 mW / °C above 25° C.

(12) Derate linearly 4.44 mW / °C above 25° C.

(13) Prior to 2004 Vcc was limited to 5.5V maximum.

(14) Do not connect input diode directly to a voltage source without an external current limiting resistor.

Block Diagram

Buffer Totem-Pole

OPB960/ OPB970/ OPB980/ OPB990

Inverter Totem-Pole

OPB962/ OPB972/ OPB982/ OPB992

Buffer Open-Collector

OPB961/ OPB971/ OPB981/ OPB991

Inverter Open-Collector

OPB963/ OPB973/ OPB983/ OPB993

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 5 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Electrical Characteristics (TA = -40° C to +70° C unless otherwise noted)

SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS

Input Diode (See OP140 / OP240 LED for additional information)

VF Forward Voltage - - 1.70 V IF = 20 mA, TA = 25° C

IR Reverse Current - - 100 µA VR = 2.0 V, TA = 25° C

Coupled (See OPL560 Detector for additional information)

VCC Operating D.C. Supply Voltage 4.5 - 16 V

ICC Supply Current - - 12 mA VCC = 4.5V to 16V

VOL Low Level Output Voltage:

Buffer Totem-Pole OPB960,OPB970

OPB980,OPB990

Buffer Open-Collector OPB961,OPB971

OPB981,OPB991 - - 0.4 V

VCC = 4.5V, IOL = 12.8mA

IF = 0 mA (14)

Inverter Totem-Pole OPB962,OPB972

OPB982,OPB992

Inverter Open-Collector OPB963,OPB973

OPB983,OPB993

VCC = 4.5V, IOL = 12.8mA

IF = 15 mA

VOH High Level Output Voltage:

Buffer Totem-Pole OPB960,OPB970

OPB980,OPB990 VCC -2.1 - - V

VCC = 4.5V to 16V, IOH = -800µA

IF = 15 mA

Inverter Totem-Pole OPB962,OPB972

OPB982,OPB992

VCC = 4.5V to 16V, IOH = -800µA

IF = 0 mA (14)

IOH High Level Output Current:

Buffer Open-Collector OPB961,OPB971

OPB981,OPB991 - - 100 µA

VCC = 4.5V to 16V, VOH = 30V

IF = 15 mA

Inverter Open-Collector OPB963,OPB973

OPB981,OPB991

VCC = 4.5V to 16V, VOH = 30V

IF = 0 mA (14)

IF(+) LED Positive-Going Threshold Current(16) - - 15 mA VCC = 5.0V, TA = 25° C

IF(+) / IF(-) Hysteresis Ratio - 1.5 - - VCC = 5.0V

tR, tF Output Rise Time, Output Fall Time - 70 - ns

tPLH, tPHL Propagation Delay Time

Low to High, High to Low - 5.0 - µs

VCC = 5.0V, IF peak= 15 mA, TA = 25° C

100 kHz square wave, C = 10pF max.

RL = 360 Ω to GND (Totem-Pole)

RL = 1KΩ pull-up (Open-Collector)

Notes:

14) Normal application would be with light source blocked, simulated by IF = 0 mA.

15) All parameters are tested using pulse techniques.

16) An increasing current applied to the LED which causes the output logic state to change.

For proper application IF(+), LED current, should be more than the stated maximum.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006

Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com

Issue C.1 1/10

Page 6 of 6

Photologic® Slotted Optical Switch

OPB960, OPB970, OPB980, OPB990 Series

OPTEK reserves the right to make any changes at any time in order to improve design and to supply the best product possible.

Logic Output vs Left to Right Bocking Distance (X-Axis Blocked)

0.0

1.0

2.0

3.0

4.0

5.0

0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.200 0.225 0.250

Distance (inches)

Logic Output (V)

Aperture Width 11

Aperture Width 51

Aperture Width 55

VCC = 5 Volts

IF = 20mA

Buffer Totem-Pole

Logic Output vs Top to Bottom Bocking Distance (Y-Axis Blocked)

0.0

1.0

2.0

3.0

4.0

5.0

0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.200 0.225 0.250

Distance (inches)

Logic Output (V)

VCC = 5 Volts

IF = 20mA

Buffer Totem-Pole