LMH2180 LMH2180 75 MHz Dual Clock Buffer Literature Number: SNAS419C LMH2180 75 MHz Dual Clock Buffer General Description Features The LMH2180 is a high speed dual clock buffer designed for portable communications and applications requiring multiple accurate multi-clock systems. The LMH2180 integrates two 75 MHz low noise buffers with independent shutdown pins into a small package. The LMH2180 ensures superb system operation between the baseband and the oscillator signal path by eliminating crosstalk between the multiple clock signals. Unique technology and design provides the LMH2180 with the ability to accurately drive both large capacitive and resistive loads. Low supply current combined with shutdown pins for each channel means the LMH2180 is ideal for battery powered applications. This part does not use an internal ground reference, thus providing additional system flexibility. The flexible buffers provide system designers the capacity to manage complex clock signals in the latest wireless applications. Each buffer delivers 106 V/s internal slew rate with independent shutdown and duty cycle precision. Each input is internally biased to 1V, removing the need for external resistors. Both channels have rail-to-rail inputs and outputs, a gain of one, and are AC coupled with the use of one capacitor. Replacing a discrete buffer solution with the LMH2180 provides many benefits: simplified board layout, minimized parasitic components, simplified BOM, design durability across multiple applications, simplification of clock paths, and the ability to reduce the number of clock signal generators in the system. The LMH2180 is produced in the tiny packages minimizing the required PCB space. (Typical values are: VSUPPLY = 2.7V and CL = 10 pF, unless otherwise specified.) 78 MHz Small signal bandwidth 2.4V to 5V Supply voltage range -123 dBc/Hz Phase noise (VIN = 1 VPP, fC = 38.4 MHz, f = 1 kHz) 106 V/s Slew rate 2.3 mA Total supply current 30 A Shutdown current Rail-to-rail input and output Individual buffer enable pins Rapid Ton technology Crosstalk rejection circuitry Packages: -- 8-Pin LLP, Solder Bump and no Pullback -- 8-Bump micro SMD -40C to 85C Temperature range Applications 3G mobile applications WLAN-WiMAX modules TD_SCDMA multi-mode MP3 and camera GSM modules Oscillator modules Typical Application 30024602 (c) 2011 National Semiconductor Corporation 300246 www.national.com LMH2180 75 MHz Dual Clock Buffer August 29, 2011 LMH2180 Soldering Information Infrared or Convection (35 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltages (V+ - V-) ESD Tolerance Human Body (Note 4) Machine Model (Note 5) Charged Device Model Storage Temperature Range Junction Temperature (Note 3) Operating Ratings (V+ 235C (Note 1) Supply Voltage - 2.4V to 5.0V Temperature Range (Note 2, Note 3) -40C to 85C Package Thermal Resistance (Note 2, Note 3) 5.5V 2000V 200V 1000V -65C to 150C 150C V-) 8-Pin LLP (JA) 217C/W 8-Bump micro SMD (JA) 90C/W 2.7V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25C, VDD = 2.7V, VSS = 0V, VCM = 1V, Enable1,2 = VDD, CL = 10 pF, RL = 30 k, Load is connected to VSS, CCOUPLING = 10 nF. Boldface limits apply at temperature range extremes of operating condition. See (Note 2) Symbol Parameter Conditions Min (Note 7) Typ (Note 6) Max (Note 7) Units Frequency Domain Response SSBW Small Signal Bandwidth VIN = 100 mVPP; -3 dB LSBW Large Signal Bandwidth GFN Gain Flatness < 0.1 dB 78 MHz VIN = 1.0 VPP; -3 dB 60 MHz f > 100 kHz 4.9 MHz VIN = 1 VPP, fC = 38.4 MHz, f = 1 kHz -123 dBc/Hz VIN = 1 VPP, fC = 38.4 MHz, f = 10 kHz -132 dBc/Hz Distortion and Noise Performance n Phase Noise en Input-Referred Voltage Noise f = 1 MHz, RSOURCE = 50 13 ISOLATION Output to Input f = 1 MHz, RSOURCE = 50 84 dB CT Crosstalk Rejection f = 38.4 MHz, VIN = 1 VPP 41 dB 0.1 VPP Step (10-90%) 6 ns 5 ns nV/ Time Domain Response tr Rise Time tf Fall Time ts Settling Time to 0.1% 1 VPP Step 120 ns OS Overshoot 0.1 VPP Step 37 % SR Slew Rate (Note 8) VIN = 2 VPP 106 V/s Enable1,2 = VDD ; No Load 2.3 2.7 2.9 mA 1.3 1.5 1.6 mA 30 41 46 A Static DC Performance IS Supply Current Enable1 = VDD , Enable2 = VSS , No Load Enable1,2 = VSS ; No Load PSRR Power Supply Rejection Ratio DC (3.0V to 5.0V) ACL Small Signal Voltage Gain VIN = 0.2 VPP VOS Output Offset Voltage TC VOS Temperature Coefficient Output Offset Voltage (Note 9) ROUT Output Resistance 68 0.95 1.0 1.05 V/V -0.5 17 18 mV 2.8 f = 100 kHz dB V/C 0.6 f = 38.4 MHz 166 disabled www.national.com 65 64 High Impedance 2 Parameter Conditions Min (Note 7) Typ (Note 6) Max (Note 7) Units Miscellaneous Performance RIN CIN ZIN VO ISC Input Resistance per Buffer Input Capacitance per Buffer Input Impedance Enable = VDD 137 Enable = VSS 137 Enable = VDD 1.3 Enable = VSS 1.3 f = 38.4 MHz, Enable = VDD 4.5 f = 38.4 MHz, Enable = VSS 4.2 Output Swing Positive VIN = VDD 2.66 2.65 Output Swing Negative VIN = VSS Output Short-Circuit Current (Note 10, Note 11) Sourcing, VIN = VDD, VOUT = VSS -21 -18 -25 Sinking, VIN = VSS, VOUT = VDD 23 15 25 k pF k 2.69 19 V 35 37 mV mA Ven_hmin Enable High Active Minimum Voltage 1.2 Ven_lmax Enable Low Inactive Maximum Voltage 0.6 V 5V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25C, VDD = 5V, VSS = 0V, VCM = 1V, Enable1,2 = VDD, CL = 10 pF, RL = 30 k, Load is connected to VSS, CCOUPLING = 10 nF. Boldface limits apply at temperature range extremes of operating condition. See (Note 2) Symbol Parameter Conditions Min (Note 7) Typ (Note 6) Max (Note 7) Units Frequency Domain Response SSBW Small Signal Bandwidth VIN = 100 mVPP; -3 dB 87 MHz LSBW Large Signal Bandwidth VIN = 1.0 VPP; -3 dB 68 MHz GFN Gain Flatness < 0.1 dB f > 100 kHz 25 MHz VIN = 1 VPP, fC = 38.4 MHz, f = 1 kHz -123 dBc/Hz VIN = 1 VPP, fC = 38.4 MHz, f = 10 kHz -132 dBc/Hz Distortion and Noise Performance n Phase Noise en Input-Referred Voltage Noise f = 1 MHz, RSOURCE = 50 12 ISOLATION Output to Input f = 1 MHz, RSOURCE = 50 84 dB CT Crosstalk Rejection f = 38.4 MHz, PIN = 0 dBm 59 dB 0.1 VPP Step (10-90%) 6 ns 6 ns 70 ns nV/ Time Domain Response tr Rise Time tf Fall Time ts Settling Time to 0.1% 1 VPP Step OS Overshoot 0.1VPP Step 13 % SR Slew Rate (Note 8) VIN = 2 VPP 124 V/s Enable1,2 = VDD ; No Load 3.4 4.0 4.1 mA 1.8 2.2 2.3 mA 32 43 49 A Static DC Performance IS Supply Current Enable1 = VDD, Enable2 = VSS ; No Load Enable1,2 = VSS ; No Load 3 www.national.com LMH2180 Symbol LMH2180 Symbol Parameter Conditions PSRR Power Supply Rejection Ratio DC (3.0V to 5.0V) ACL Small Signal Voltage Gain VIN = 0.2 VPP VOS Output Offset Voltage TC VOS Temperature Coefficient Output Offset Voltage (Note 9) ROUT Output Resistance Min (Note 7) Typ (Note 6) Max (Note 7) 65 64 68 0.95 1.0 1.05 V/V -1.4 21 22 mV dB 2.4 f = 100 kHz 0.5 f = 38.4 MHz 126 disabled Units V/C High Impedance Miscellaneous Performance RIN CIN ZIN VO ISC Input Resistance per Buffer Input Capacitance per Buffer Input Impedance Enable = VDD 138 Enable = VSS 138 Enable = VDD 1.3 Enable = VSS 1.3 f = 38.4 MHz, Enable = VDD 4.3 f = 38.4 MHz, Enable = VSS 4.2 Output Swing Positive VIN = VDD 4.96 4.95 Output Swing Negative VIN = VSS Output Short-Circuit Current (Note 10, Note 11) Sourcing, VIN = VDD, VOUT = VSS -80 -62 -90 Sinking, VIN = VSS, VOUT = VDD 60 43 65 k pF k 4.99 10 V 35 50 mV mA Ven_hmin Enable High Active Minimum Voltage 1.2 Ven_lmax Enable Low Inactive Maximum Voltage 0.6 V Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of the device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. All voltages are measured with respect to the ground pin, unless otherwise specified. Note 2: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJ(MAX), JA , and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA) / JA or the number given in the Absolute Maximum Ratings, whichever is lower. Note 4: Human body model, applicable std. JESD22-A114C. Note 5: Machine model, applicable std. JESD22-A115-A. Note 6: Typical values represent the most likely parametric norms at TA = +25C, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 7: Datasheet min/max specification limits are guaranteed by test or statistical analysis. Note 8: Slew rate is the average of the rising and falling slew rates. Note 9: Average Temperature Coefficient is determined by dividing the changing in a parameter at temperature extremes by the total temperature change. Note 10: Short-Circuit test is a momentary test. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Note 11: Positive current corresponds to current flowing into the device. www.national.com 4 LMH2180 Block Diagram 30024601 Pin Descriptions Pin No. LLP Pin No. microSMD 1 A3 VDD Voltage supply connection 2 A2 IN 1 Input 1 3 A1 IN 2 Input 2 4 B1 ENABLE 2 5 C1 VSS 6 C2 OUT 2 Output 2 7 C3 OUT 1 Output 1 8 B3 ENABLE 1 Pin Name Description Enable buffer 2 Ground connection Enable buffer 1 Connection Diagrams 8-Pin LLP 8-Bump micro SMD 30024631 Top View 30024649 Top View Ordering Information Package Part Number 8-Pin LLP Solder Bump LMH2180YD 8-Pin LLP No Pullback 8-Bump micro SMD LMH2180YDX Package Marking 2180Y 4.5k Units Tape and Reel LMH2180SD LMH2180SDE LMH2180TMX NSC Drawing YDA08A 1k Units Tape and Reel 2180S 250 Units Tape and Reel LMH2180SDX LMH2180TM Transport Media 1k Units Tape and Reel SDA08A 4.5k Units Tape and Reel 250 Units Tape and Reel CA 3k Units Tape and Reel 5 TMD08AAA www.national.com LMH2180 Typical Performance Characteristics TA = 25C, VDD = 2.7V, VSS = 0V, Enable1,2 = VDD, CL = 10 pF, RL = 30 k and CCOUPLING = 10 nF, unless otherwise specified. Frequency Response Phase Response 30024603 30024604 Frequency Response Over Temperature Frequency Response Over Temperature 30024605 30024606 Phase Response Over Temperature Phase Response Over Temperature 30024607 www.national.com 30024608 6 LMH2180 Large Signal Bandwidth Gain Flatness < 0.1 dB (GFN) 30024609 30024610 Voltage Noise Phase Noise 30024611 30024612 Isolation Output to Input vs. Frequency Crosstalk Rejection vs. Frequency 30024613 30024614 7 www.national.com LMH2180 Transient Response Positive Transient Response Negative 30024615 30024616 Small Signal Pulse Response Small Signal Pulse Response 30024617 30024618 Large Signal Response Large Signal Response 30024619 www.national.com 30024620 8 LMH2180 ISUPPLY vs. VSUPPLY ISUPPLY vs. VSUPPLY 30024622 30024621 ISUPPLY vs. VSUPPLY PSRR vs. Frequency 30024623 30024624 VOS vs. VSUPPLY ROUT vs. Frequency 30024625 30024626 9 www.national.com LMH2180 Input Impedance vs. Frequency VOUT vs. IOUT (Sourcing) 30024628 30024627 VOUT vs. IOUT (Sourcing) VOUT vs. IOUT (Sinking) 30024630 30024629 VOUT vs. IOUT (Sinking) ISC Sourcing vs. VSUPPLY Over Temperature 30024633 30024632 www.national.com 10 LMH2180 ISC Sinking vs. VSUPPLY Over Temperature ISUPPLY vs. VENABLE 30024634 30024635 ISUPPLY vs. VENABLE 30024636 11 www.national.com LMH2180 teristic graphic entitled Isolation Output to Input vs. Frequency. A block diagram of the isolation is shown in Figure 2. Crosstalk rejection between buffers prevents signals from affecting each other. Figure 2 shows a Baseband IC and a Bluetooth module as an example. See the characteristic graphic labeled Crosstalk Rejection vs. Frequency for more information. Application Information GENERAL The LMH2180 is designed to minimize the effects of spurious signals from the base chip to the oscillator. Also the influence of varying load resistance and capacitance to the oscillator is minimized, while the drive capability is increased. The inputs of the LMH2180 are internally biased at 1V, making AC coupling possible without external bias resistors. To optimize current consumption, a buffer that is not in use can be disabled by connecting it's enable pin to VSS. The LMH2180 has no internal ground reference; therefore, either single or split supply configurations can be used. The LMH2180 is an easy replacement for discrete circuitry. It simplifies board layout and minimizes the effect of layout related parasitic components. INPUT CONFIGURATION The internal 1V input biasing allows AC coupling of the input signal. This biasing avoids the use of external resistors, as depicted in Figure 1. The biasing prevents a large DC load at the oscillators output that creates a load impedance and may affect it's oscillating frequency. As a result of this biasing, the maximum amplitude of the AC signal is 2VPP. The coupling capacitance C1 should be large enough to let the AC signal pass. This is a unity gain buffer with rail-to-rail inputs and outputs. 30024645 FIGURE 2. Isolation Block Diagram DRIVING CAPACITIVE LOADS Each buffer can drive a capacitive load. Be aware that every capacitor directly connected to the output becomes part of the loop of the buffer. In most applications the load consists of the capacitance of copper tracks and the input capacitance of the application blocks. Capacitance reduces the gain/phase margin and decreases the stability. This leads to peaking in the frequency response and in extreme situations oscillations can occur. To drive a large capacitive load it is recommended to include a series resistor between the buffer and the load capacitor. The best value for this isolation resistance can be found by experimentation. The LMH2180 datasheet reflects measurements with capacitive loads of 10 pF at the output of the buffers. Most common applications will probably use a lower capacitive load, which will result in lower peaking and significantly greater bandwidth, see Figure 3. 30024644 FIGURE 1. Input Configuration FREQUENCY PULLING Frequency pulling is the frequency variation of an oscillator caused by a varying load. In the typical application, the load of the oscillator is a fixed capacitor (C1) in series with the input impedance of the buffer. To keep the input impedance as constant as possible, the input is biased at 1V, even when the part is disabled. A simplified schematic of the input configuration is shown in Figure 1. ISOLATION AND CROSSTALK Output to input isolation prevents the clock signal of the oscillator from being affected by spurious signals generated by the digital blocks behind the output buffer. See the charac- www.national.com 30024646 FIGURE 3. Bandwidth and Peaking 12 LAYOUT DESIGN RECOMMENDATION Careful consideration during circuit design and PCB layout will eliminate problems and will optimize the performance of the LMH2180. It is best to have the same ground plane on the PCB for all decoupling and other ground connections. To ensure a clean supply voltage it is best to place decoupling capacitors close to the LMH2180, between VDD and VSS. Another important issue is the value of the components, because this also determines the sensitivity to disturbances. Resistor values have to be low enough to avoid a significant noise contribution and large enough to avoid a significant increase in power consumption while loading inputs or outputs to heavily. 30024648 FIGURE 4. Phase Noise 30024647 FIGURE 5. Measurement Setup 13 www.national.com LMH2180 Figure 5 shows the setup used to measure the LMH2180 phase noise. The clock driving the LMH2180 is a state of the art 38.4MHz TCXO. Both the TCXO phase noise and the phase noise at the LMH2180 output were measured. At offset frequencies of 1 kHz and higher from the carrier, the TCXO phase noise is sufficiently low to accurately calculate the LMH2180 contribution to the phase noise at the output. The LMH6559, whose phase noise contribution can be neglected, is used to drive the 50 input impedance of the Signal Source Analyzer. PHASE NOISE A clock buffer adds noise to the clock signal. This noise causes uncertainty in the phase of the clock signal. This uncertainty is described by jitter (time domain) or phase noise (frequency domain). Communication systems, such as Wireless LAN, require a low jitter/phase noise clock signal to obtain a low Bit Error Rate. Figure 4 shows the frequency domain representation of a clock signal with frequency fC. Without Phase Noise the entire signal power would only be located at the frequency fC. Phase Noise spreads some of the power to adjacent frequencies. Phase Noise is usually specified in dBc/Hz at a given frequency offset f from the carrier, where dBc is the power level in dB relative to the carrier. The noise power is measured within a 1 Hz bandwidth. LMH2180 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin LLP NS Package Number YDA08A 8-Pin LLP NS Package Number SDA08A www.national.com 14 LMH2180 8-Bump micro SMD NS Package Number TMD08AAA X1 = 1.215 0.030 mm, X2 = 1.215 0.030 mm, X3 = 0.600 0.075 mm 15 www.national.com LMH2180 75 MHz Dual Clock Buffer Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated