Ordering number : ENN5066B CMOS IC LC75854E, 75854W 1/4 Duty LCD Display Drivers with Key Input Function Overview Package Dimensions The LC75854E and LC75854W are 1/4 duty LCD display drivers that can directly drive up to 164 segments and can control up to four general-purpose output ports. These products also incorporate a key scan circuit that accepts input from up to 30 keys to reduce printed circuit board wiring. unit: mm 3159-QFP64E [LC75854E] 0.8 1.0 17.2 14.0 0.35 1.6 1.0 32 1.6 1.0 49 0.8 3.0max 17 1.0 * Key input function for up to 30 keys (A key scan is performed only when a key is pressed.) * 1/4 duty - 1/2 bias and 1/4 duty - 1/3 bias drive schemes can be controlled from serial data (up to 164 segments). * Sleep mode and all segments off functions that are controlled from serial data * Segment output port/general-purpose output port function switching that is controlled from serial data * Serial data I/O supports CCB format communication with the system controller. * Direct display of display data without the use of a decoder provides high generality. * Provision of an on-chip voltage-detection type reset circuit prevents incorrect displays. * RC oscillator circuit 17.2 14.0 Features 0.15 33 48 64 1 16 15.6 0.1 2.7 0.8 SANYO: QFP64E unit: mm 3190-SQFP64 [LC75854W] 12.0 10.0 1.25 0.5 0.18 1.25 0.15 33 48 49 0.5 12.0 10.0 1.25 32 16 0.1 1.25 1 1.7max 17 64 * CCB is a trademark of SANYO ELECTRIC CO., LTD. 0.5 0.5 SANYO: SQFP64 * CCB is SANYO's original bus format and all the bus addresses are controlled by SANYO. Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Company TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN O3099TH (OT)/N3095HA (OT)/52295TH (OT) No. 5066-1/25 LC75854E, 75854W Specifications Absolute Maximum Ratings at Ta = 25C, VSS = 0 V Parameter Symbol VDD max Maximum supply voltage Input voltage Output voltage Output current Allowable power dissipation Conditions Ratings Unit VDD -0.3 to +7.0 VIN1 CE, CL, DI -0.3 to +7.0 V V VIN2 OSC, KI1 to KI5, TEST, VDD1, VDD2 -0.3 to VDD + 0.3 V VOUT1 DO VOUT2 OSC, S1 to S41, COM1 to COM4, KS1 to KS6, P1 to P4 IOUT1 S1 to S41 300 A IOUT2 COM1 to COM4 3 mA IOUT3 KS1 to KS6 1 mA IOUT4 P1 to P4 5 mA 200 mW Pd max -0.3 to +7.0 V -0.3 to VDD + 0.3 V Ta = 85C Operating temperature Topr -40 to +85 C Storage temperature Tstg -55 to +125 C Allowable Operating Ranges at Ta = -40 to +85C, VSS = 0 V Parameter Supply voltage Input voltage Input high level voltage Input low level voltage Symbol Conditions Ratings min typ max Unit VDD VDD 6.0 V VDD1 VDD1 2/3 VDD VDD V VDD2 VDD2 1/3 VDD VDD V VIH1 CE, CL, DI 0.8 VDD 6.0 V VIH2 KI1 to KI5 0.6 VDD VDD V 0 0.2 VDD V VIL CE, CL, DI, KI1 to KI5 4.5 Recommended external resistance ROSC OSC 62 k Recommended external capacitance COSC OSC 680 pF Guaranteed oscillation range fOSC OSC 25 50 100 kHz Data setup time tds CL, DI: Figure 2 160 Data hold time tdh CL, DI: Figure 2 160 ns ns CE wait time tcp CE, CL: Figure 2 160 ns CE setup time tcs CE, CL: Figure 2 160 ns CE hold time tch CE, CL: Figure 2 160 ns High level clock pulse width toH CL: Figure 2 160 ns Low level clock pulse width toL CL: Figure 2 160 ns Rise time tr CE, CL, DI: Figure 2 160 Fall time tf CE, CL, DI: Figure 2 160 ns ns DO output delay time tdc DO, RPU = 4.7 k, CL = 10 pF*1: Figure 2 1.5 s DO rise time tdr DO, RPU = 4.7 k, CL = 10 pF*1: Figure 2 1.5 s Note: *1. Since DO is an open-drain output, these values depend on the resistance of the pull-up resistor RPU and the load capacitance CL. No. 5066-2/25 LC75854E, 75854W Electrical Characteristics for the Allowable Operating Ranges Parameter Hysteresis Power-down detection voltage Symbol VH CE, CL, DI: VI = 6.0 V IIL CE, CL, DI: VI = 0 V Input floating voltage VIF KI1 to KI5 Pull-down resistance RPD KI1 to KI5: VDD = 5.0 V Output middle level voltage*2 Oscillator frequency Current drain Unit max 0.1 VDD 2.7 IIH Output low level voltage typ CE, CL, DI Input low level current Output high level voltage min VDET Input high level current Output off leakage current Ratings Conditions 3.0 V 3.3 5.0 -5.0 V A A 0.05 VDD V 50 100 250 k 6.0 A VDD - 0.5 VDD - 0.2 IOFFH DO: VO = 6.0 V VOH1 KS1 to KS6: IO = -500 A VDD - 1.2 VOH2 P1 to P4: IO = -1 mA VDD - 1.0 V VOH3 S1 to S41: IO = -20 A VDD - 1.0 V VOH4 COM1 to COM4: IO = -100 A VDD - 1.0 VOL1 KS1 to KS6: IO = 25 A VOL2 0.2 V V 0.5 1.5 V P1 to P4: IO = 1 mA 1.0 V VOL3 S1 to S41: IO = 20 A 1.0 V VOL4 COM1 to COM4: IO = 100 A 1.0 V VOL5 DO: IO = 1 mA 0.1 0.5 V 1/2 VDD + 1.0 V VMID1 COM1 to COM4: 1/2 bias, IO = 100 A 1/2 VDD - 1.0 VMID2 S1 to S41: 1/3 bias, IO = 20 A 2/3 VDD - 1.0 2/3 VDD + 1.0 V VMID3 S1 to S41: 1/3 bias, IO = 20 A 1/3 VDD - 1.0 1/3 VDD + 1.0 V VMID4 COM1 to COM4: 1/3 bias, IO = 100 A 2/3 VDD - 1.0 2/3 VDD + 1.0 V VMID5 COM1 to COM4: 1/3 bias, IO = 100 A 1/3 VDD - 1.0 1/3 VDD + 1.0 V fOSC OSC: R = 62 k, C = 680 pF IDD1 Sleep mode 40 IDD2 VDD = 6.0 V, output open, 1/2 bias, fOSC = 50 kHz IDD3 VDD = 6.0 V, output open, 1/3 bias, fOSC = 50 kHz 50 60 kHz 100 A 250 500 A 200 400 A Note: *2. Excluding the bias voltage generation divider resistor built into VDD1 and VDD2. (See Figure 1.) To the common segment driver Excluding these resistors. Figure 1 No. 5066-3/25 LC75854E, 75854W 1. When CL is stopped at the low level 2. When CL is stopped at the high level Figure 2 No. 5066-4/25 LC75854E, 75854W Block Diagram Pin Assignment No. 5066-5/25 LC75854E, 75854W Pin Functions Pin Pin No. S1/P1 to S4/P4 1 to 4 S5 to S39 5 to 39 COM1 40 COM2 41 COM3 42 COM4 43 KS1/S40, 44 KS2/S41, 45 KS3 to KS6 46 to 49 KI1 to KI5 50 to 54 OSC 60 CE 62 CL 63 DI 64 DO Active I/O Handling when unused -- O Open Common driver outputs The frame frequency fO is given by: fO = (fOSC/512) Hz. -- O Open Key scan outputs Although normal key scan timing lines require diodes to be inserted in the timing lines to prevent shorts, since these outputs are unbalanced CMOS transistor outputs, these outputs will not be damaged by shorting when these outputs are used to form a key matrix. The KS1/S40 and KS2/S41 pins can be used as segment outputs when so specified by the control data. -- O Open Key scan inputs These pins have built-in pull-down resistors. H I GND Oscillator connection An oscillator circuit is formed by connecting an external resistor and capacitor at this pin. -- I/O VDD H I Function Segment outputs for displaying the display data transferred by serial data input. The S1/P1 to S4/P4 pins can be used as general-purpose output ports under serial data control. Serial data interface connections to the controller. Note that DO, being an open-drain output, requires a pull-up resistor. I GND -- I 61 CE: Chip enable CL: Synchronization clock DI: Transfer data DO: Output data -- O Open TEST 55 This pin must be connected to ground. -- I -- VDD1 57 Used for applying the LCD drive 2/3 bias voltage externally. Must be connected to VDD2 when a 1/2 bias drive scheme is used. -- I Open VDD2 58 Used for applying the LCD drive 1/3 bias voltage externally. Must be connected to VDD1 when a 1/2 bias drive scheme is used. -- I Open VDD 56 Power supply connection. Provide a voltage of between 4.5 and 6.0 V. -- -- -- VSS 59 Power supply connection. Connect to ground. -- -- -- No. 5066-6/25 LC75854E, 75854W Serial Data Input 1. When CL is stopped at the low level Display data Display data Display data Display data Control data Fixed data Fixed data Fixed data Note: DD: Direction data No. 5066-7/25 LC75854E, 75854W 2. When CL is stopped at the high level Control data Display data Display data Fixed data Display data Fixed data Display data Fixed data Note: DD: Direction data * * * * * * * CCB address......42H D1 to D164........Display data S0, S1 ................Sleep control data K0, K1...............Key scan output/segment output selection data P0, P1 ................Segment output port/general-purpose output port selection data SC......................Segment on/off control data DR .....................1/2 bias or 1/3 bias drive selection data No. 5066-8/25 LC75854E, 75854W Control Data Functions 1. S0, S1: Sleep control data These control data bits switch between normal mode and sleep mode and set the states of the KS1 to KS6 key scan outputs during key scan standby. Control data Output pin states during key scan standby Mode OSC oscillator Segment outputs Common outputs KS1 KS2 KS3 KS4 KS5 0 Normal Operating Operating H H H H H H 0 1 Sleep Stopped L L L L L L H 1 0 Sleep Stopped L L L L L H H 1 1 Sleep Stopped L H H H H H H S0 S1 0 KS6 Note: This assumes that the KS1/S40 and KS2/S41 output pins are selected for key scan output. 2. K0, K1: Key scan output/segment output selection data These control data bits switch the functions of the KS1/S40 and KS2/S41 output pins between key scan output and segment output. Control data Output pin state Maximum number of input keys K0 K1 KS1/S40 KS2/S41 0 0 KS1 KS2 30 0 1 S40 KS2 25 1 S40 S41 20 : don't care 3. P0, P1: Segment output port/general-purpose output port selection data These control data bits switch the functions of the S1/P1 to S4/P4 output pins between the segment output port and the general-purpose output port. Control data Output pin state P0 P1 S1/P1 S2/P2 S3/P3 S4/P4 0 0 S1 S2 S3 S4 0 1 P1 P2 S3 S4 1 0 P1 P2 P3 S4 1 1 P1 P2 P3 P4 The table below lists the correspondence between the display data and the output pins when these pins are selected to be general-purpose output ports. Output pin Corresponding display data S1/P1 D1 S2/P2 D5 S3/P3 D9 S4/P4 D13 For example, if the S4/P4 output pin is selected to be a general-purpose output port, the S4/P4 output pin will output a high level when the display data D13 is 1. 4. SC: Segment on/off control data This control data bit controls the on/off state of the segments. SC Display state 0 On 1 Off However, note that when the segments are turned off by setting SC to 1, the segments are turned off by outputting segment off waveforms from the segment output pins. No. 5066-9/25 LC75854E, 75854W 5. DR: 1/2 bias or 1/3 bias drive selection data This control data bit switches between LCD 1/2 bias or 1/3 bias drive. DR Drive scheme 0 1/3 bias drive 1 1/2 bias drive Display Data and Output Pin Correspondence COM1 COM2 COM3 COM4 COM1 COM2 COM3 COM4 S1/P1 Output pin D1 D2 D3 D4 S21 Output pin D81 D82 D83 D84 S2/P2 D5 D6 D7 D8 S22 D85 D86 D87 D88 S3/P3 D9 D10 D11 D12 S23 D89 D90 D91 D92 S4/P4 D13 D14 D15 D16 S24 D93 D94 D95 D96 S5 D17 D18 D19 D20 S25 D97 D98 D99 D100 S6 D21 D22 D23 D24 S26 D101 D102 D103 D104 S7 D25 D26 D27 D28 S27 D105 D106 D107 D108 S8 D29 D30 D31 D32 S28 D109 D110 D111 D112 S9 D33 D34 D35 D36 S29 D113 D114 D115 D116 S10 D37 D38 D39 D40 S30 D117 D118 D119 D120 S11 D41 D42 D43 D44 S31 D121 D122 D123 D124 S12 D45 D46 D47 D48 S32 D125 D126 D127 D128 S13 D49 D50 D51 D52 S33 D129 D130 D131 D132 S14 D53 D54 D55 D56 S34 D133 D134 D135 D136 S15 D57 D58 D59 D60 S35 D137 D138 D139 D140 S16 D61 D62 D63 D64 S36 D141 D142 D143 D144 S17 D65 D66 D67 D68 S37 D145 D146 D147 D148 S18 D69 D70 D71 D72 S38 D149 D150 D151 D152 S19 D73 D74 D75 D76 S39 D153 D154 D155 D156 S20 D77 D78 D79 D80 KS1/S40 D157 D158 D159 D160 KS2/S41 D161 D162 D163 D164 For example, the table below lists the segment output states for the S11 output pin. Display data Output pin state D41 D42 D43 D44 S11 0 0 0 0 The LCD segments for COM1, COM2, COM3 and COM4 are off. 0 0 0 1 The LCD segment for COM4 is on. 0 0 1 0 The LCD segment for COM3 is on. 0 0 1 1 The LCD segments for COM3 and COM4 are on. 0 1 0 0 The LCD segment for COM2 is on. 0 1 0 1 The LCD segments for COM2 and COM4 are on. 0 1 1 0 The LCD segments for COM2 and COM3 are on. 0 1 1 1 The LCD segments for COM2, COM3 and COM4 are on. 1 0 0 0 The LCD segment for COM1 is on. 1 0 0 1 The LCD segments for COM1 and COM4 are on. 1 0 1 0 The LCD segments for COM1 and COM3 are on. 1 0 1 1 The LCD segments for COM1, COM3 and COM4 are on. 1 1 0 0 The LCD segments for COM1 and COM2 are on. 1 1 0 1 The LCD segments for COM1, COM2 and COM4 are on. 1 1 1 0 The LCD segments for COM1, COM2 and COM3 are on. 1 1 1 1 The LCD segments for COM1, COM2, COM3 and COM4 are on. No. 5066-10/25 LC75854E, 75854W Serial Data Output 1. When CL is stopped at the low level Output data 2. When CL is stopped at the high level Output data * CCB address...............43H * KD1 to KD30 .............Key data * SA...............................Sleep acknowledge data Note: If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data (SA) will be invalid. Output Data 1. KD1 to KD30: Key data When a key matrix of up to 30 keys is formed from the KS1 to KS6 output pins and the KI1 to KI5 input pins and one of those keys is pressed, the key output data corresponding to that key will be set to 1. The table shows the relationship between those pins and the key data bits. KS1/S40 KI1 KI2 KI3 KI4 KI5 KD1 KD2 KD3 KD4 KD5 KS2/S41 KD6 KD7 KD8 KD9 KD10 KS3 KD11 KD12 KD13 KD14 KD15 KS4 KD16 KD17 KD18 KD19 KD20 KS5 KD21 KD22 KD23 KD24 KD25 KS6 KD26 KD27 KD28 KD29 KD30 When the KS1/S40 and KS2/S41 output pins are selected to be segment outputs by control data bits K0 and K1 and a key matrix of up to 20 keys is formed using the KS3 to KS6 output pins and the KI1 to KI5 input pins, the KD1 to KD10 key data bits will be set to 0. 2. SA: Sleep acknowledge data This output data bit is set to the state when the key was pressed. Also, while DO will be low in this case, if serial data is input and the mode is set (to normal or sleep mode) during this period, that mode will be set. SA will be 1 in sleep mode and 0 in normal mode. No. 5066-11/25 LC75854E, 75854W Sleep Mode Functions Sleep mode is set up by setting S0 or S1 in the control data to 1. The segment outputs will all go low and the common outputs will also go low, and the oscillator on the OSC pin will stop (it will be started by a key press). This reduces power dissipation. This mode is cleared by sending control data with both S0 and S1 set to 0. However, note that the S1/P1 to S4/P4 outputs can be used as general-purpose output ports according to the state of the P0 and P1 control data bits, even in sleep mode. (See the control data description for details.) Key Scan Operation Functions 1. Key scan timing The key scan period is 384 T (s). To reliably determine the on/off state of the keys, the LC75854E/W scans the keys twice and determines that a key has been pressed when the key data agrees. It outputs a key data read request (a low level on DO) 800 T (s) after starting a key scan. If the key data does not agree and a key was pressed at that point, it scans the keys again. Thus the LC75854E/W cannot detect a key press shorter than 800 T (s). Note: *3. In sleep mode the high/low state of these pins is determined by the S0 and S1 bits in the control data. Key scan output signals are not output from pins that are set low. 2. In normal mode * The pins KS1 to KS6 are set high * When a key is pressed a key scan is started and the keys are scanned until all keys are released. Multiple key presses are recognized by determining whether multiple key data bits are set. 1 * If a key is pressed for longer than 800 T (s) (where T = ) the LC75854E/W outputs a key data read request (a fOSC low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if CE is high during a serial data transfer, DO will be set high. * After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75854E/W performs another key scan. Also note that DO, being an open-drain output, requires a pull-up resistor (between 1 and 10 k). No. 5066-12/25 LC75854E, 75854W Key input 1 Key input 2 Key scan Serial data transfer Serial data transfer Key address (43H) Serial data transfer Key data read Key data read request Key address Key data read Key data read request Key address Key data read Key data read request 3. In sleep mode * The pins KS1 to KS6 are set to high or low by the S0 and S1 bits in the control data. (See the control data description for details.) * If a key on one of the lines corresponding to a KS1 to KS6 pin which is set high is pressed, the oscillator on the OSC pin is started and a key scan is performed. Keys are scanned until all keys are released. Multiple key presses are recognized by determining whether multiple key data bits are set. 1 * If a key is pressed for longer than 800 T (s) (where T = ) the LC75854E/W outputs a key data read request (a fOSC low level on DO) to the controller. The controller acknowledges this request and reads the key data. However, if CE is high during a serial data transfer, DO will be set high. * After the controller reads the key data, the key data read request is cleared (DO is set high) and the LC75854E/W performs another key scan. However, this does not clear sleep mode. Also note that DO, being an open-drain output, requires a pull-up resistor (between 1 and 10 k). * Sleep mode key scan example Example: S0 = 0, S1 = 1 (sleep with only KS6 high) When any one of these keys is pressed, the oscillator on the OSC pin is started and the keys are scanned. Note *4. These diodes are required to reliable recognize multiple key presses on the KS6 line when sleep mode state with only KS6 high, as in the above example. That is, these diodes prevent incorrect operations due to sneak currents in the KS6 key scan output signal when keys on the KS1 to KS5 lines are pressed at the same time. No. 5066-13/25 LC75854E, 75854W Key input (KS6 line) Key scan Serial data transfer Serial data transfer Key address (43H) Key data read Key data read request Serial data transfer Key address Key data read Key data read request Multiple Key Presses Although the LC75854E/W is capable of key scanning without inserting diodes for dual key presses, triple key presses on the KI1 to KI5 input pin lines, or multiple key presses on the KS1 to KS6 output pin lines, multiple presses other than these cases may result in keys that were not pressed recognized as having been pressed. Therefore, a diode must be inserted in series with each key. Applications that do not recognize multiple key presses of three or more keys should check the key data for three or more 1 bits and ignore such data. No. 5066-14/25 LC75854E, 75854W 1/4 Duty, 1/2 Bias Drive Technique COM1 COM2 COM3 COM4 LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are turned off. LCD driver output when only LCD segments corresponding to COM1 are on LCD driver output when only LCD segments corresponding to COM2 are on. LCD driver output when LCD segments corresponding to COM1 and COM2 are on. LCD driver output when only LCD segments corresponding to COM3 are on. LCD driver output when LCD segments corresponding to COM1 and COM3 are on. LCD driver output when LCD segments corresponding to COM2 and COM3 are on. LCD driver output when LCD segments corresponding to COM1, COM2 and COM3 are on. LCD driver output when only LCD segments corresponding to COM4 are on. LCD driver output when LCD segments corresponding to COM2 and COM4 are on. LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are on. 1/4 Duty, 1/2 Bias Waveforms No. 5066-15/25 LC75854E, 75854W 1/4 Duty, 1/3 Bias Drive Technique COM1 COM2 COM3 COM4 LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are turned off. LCD driver output when only LCD segments corresponding to COM1 are on LCD driver output when only LCD segments corresponding to COM2 are on. LCD driver output when LCD segments corresponding to COM1 and COM2 are on. LCD driver output when only LCD segments corresponding to COM3 are on. LCD driver output when LCD segments corresponding to COM1 and COM3 are on. LCD driver output when LCD segments corresponding to COM2 and COM3 are on. LCD driver output when LCD segments corresponding to COM1, COM2 and COM3 are on. LCD driver output when only LCD segments corresponding to COM4 are on. LCD driver output when LCD segments corresponding to COM2 and COM4 are on. LCD driver output when all LCD segments corresponding to COM1, COM2, COM3 and COM4 are on. 1/4 Duty, 1/3 Bias Waveforms No. 5066-16/25 LC75854E, 75854W Voltage Detection Type Reset Circuit (VDET) This circuit generates an output signal and resets the system when power is first applied and when the voltage drops, i.e., when the power supply voltage is less than or equal to the power down detection voltage VDET, which is 3.0 V, typical. To assure that this function operates reliably, a capacitor must be added to the power supply line so that the power supply voltage VDD rise time when power is first applied and the power supply voltage VDD fall time when the voltage drops are both at least 1 ms. (See Figure 3.) System Reset 1. Reset method If at least 1 ms is assured as the supply voltage VDD rise time when power is applied, a system reset will be applied by the VDET output signal when the supply voltage is brought up. If at least 1 ms is assured as the supply voltage VDD fall time when power drops, a system reset will be applied in the same manner by the VDET output signal when the supply voltage is lowered. Note that the reset is cleared at the point when all the serial data (the display data D1 to D164 and the control data) has been transferred, i.e., on the fall of the CE signal on the transfer of the last direction data, after all the direction data has been transferred. (See Figure 3.) Display and control data transfer Internal data Undefined Defined System reset period Power supply voltage VDD rise time: t1 1 ms Power supply voltage VDD fall time: t2 1 ms Figure 3 2. LC75854E/W internal block states during the reset period * CLOCK GENERATOR Reset is applied and the base clock is stopped. However the OSC pin state (normal or sleep mode) is determined after the S0 and S1 control data bits are transferred. * COMMON DRIVER, SEGMENT DRIVER & LATCH Reset is applied and the display is turned off. However, display data can be input to the latch circuit in this state. * KEY SCAN Reset is applied, the circuit is set to the initial state, and at the same time the key scan operation is disabled. * KEY BUFFER Reset is applied and all the key data is set to low. * CCB INTERFACE, CONTROL REGISTER, SHIFT REGISTER Since serial data transfer is possible, these circuits are not reset. No. 5066-17/25 LC75854E, 75854W Blocks that are reset 3. Output pin states during the reset period Output pin S1/P1 to S4/P4 State during reset L*5 S5 to S39 L COM1 to COM4 L KS1/S40, KS2/S41 L*5 KS3 to KS5 *6 KS6 H DO H*7 : Don't care Note: * 5. These output pins are forcibly set to the segment output function and held low. * 6. When power is first applied, these output pins are undefined until the S0 and S1 control data bits have been transferred. * 7. Since this output pin is an open-drain output, a pull-up resistor of between 1 and 10 k is required. This pin remains high during the reset period even if a key data read operation is performed. No. 5066-18/25 LC75854E, 75854W Sample Application Circuit 1 (P1) 1/2 bias (for use with normal panels) (P2) (P3) (P4) (general-purpose output ports) Used with the backlight controller or other circuit. OSC COM1 VDD *8 C 0.047 F COM2 COM3 VSS COM4 TEST P1/S1 P2/S2 VDD1 P3/S3 VDD2 P4/S4 S5 C From the controller To the controller To the controller power supply LCD panel (up to 164 segments) +5V *9 CE CL DI K K K K K DO I I I I I 5 4 3 2 1 S 4 1 / KKKKK SSSSS 6 5 4 3 2 S39 S 4 0 / K S 1 (S40) (S41) Key matrix (up to 30 keys) Note: *8.Add a capacitor to the power supply line so that the power supply voltage VDD rise time when power is applied and the power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75854E/W is reset by the VDET. *9.The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 k) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 5066-19/25 LC75854E, 75854W Sample Application Circuit 2 1/2 bias (for use with large panels) (P1) (P2) (P3) (P4) (general-purpose output ports) Used with the backlight controller or other circuit. OSC COM1 VDD *8 C 0.047 F C From the controller To the controller To the controller power supply *9 COM3 VSS COM4 TEST P1/S1 R 10k R 1 k R COM2 LCD panel (up to 164 segments) +5V P2/S2 VDD1 P3/S3 VDD2 P4/S4 S5 CE CL DI K K K K K DO I I I I I 5 4 3 2 1 S 4 1 / KKKKK SSSSS 6 5 4 3 2 S39 S 4 0 / K S 1 (S40) (S41) Key matrix (up to 30 keys) Note: *8.Add a capacitor to the power supply line so that the power supply voltage VDD rise time when power is applied and the power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75854E/W is reset by the VDET. *9.The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 k) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 5066-20/25 LC75854E, 75854W Sample Application Circuit 3 1/3 bias (for use with normal panels) (P1) (P2) (P3) (P4) (general-purpose output ports) Used with the backlight controller or other circuit. OSC COM1 VDD *8 C 0.047 F COM3 VSS COM4 TEST P1/S1 P2/S2 C From the controller To the controller To the controller power supply COM2 LCD panel (up to 164 segments) +5V *9 VDD1 P3/S3 VDD2 P4/S4 S5 C CE CL DI K K K K K DO I I I I I 5 4 3 2 1 S 4 1 / KKKKK SSSSS 6 5 4 3 2 S39 S 4 0 / K S 1 (S40) (S41) Key matrix (up to 30 keys) Note: *8.Add a capacitor to the power supply line so that the power supply voltage VDD rise time when power is applied and the power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75854E/W is reset by the VDET. *9.The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 k) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. No. 5066-21/25 LC75854E, 75854W Sample Application Circuit 4 1/3 bias (for use with large panels) (P1) (P2) (P3) (P4) (general-purpose output ports) Used with the backlight controller or other circuit. OSC COM1 VDD *8 C 0.047 F R C C From the controller To the controller To the controller power supply COM3 VSS COM4 TEST P1/S1 R 10k R 1 k *9 COM2 LCD panel (up to 164 segments) +5V P2/S2 VDD1 P3/S3 VDD2 P4/S4 R S5 CE CL DI K K K K K DO I I I I I 5 4 3 2 1 S 4 1 / KKKKK SSSSS 6 5 4 3 2 S39 S 4 0 / K S 1 (S40) (S41) Key matrix (up to 30 keys) Note: *8.Add a capacitor to the power supply line so that the power supply voltage VDD rise time when power is applied and the power supply voltage VDD fall time when power drops are both at least 1 ms, as the LC75854E/W is reset by the VDET. *9.The DO pin, being an open-drain output, requires a pull-up resistor. Select a resistance (between 1 to 10 k) appropriate for the capacitance of the external wiring so that signal waveforms are not degraded. Notes on transferring display data from the controller The display data (D1 to D164) is transferred to the LC75854E/W in four operations. All of the display data should be transferred within 30 ms to maintain the quality of the displayed image. Notes on the controller key data read techniques 1. Timer based key data acquisition Key data read processing No. 5066-22/25 LC75854E, 75854W * Timing chart Key input Key scan Key address Key data read Key data read request Controller determination (key on) Controller determination Controller determination (key on) (key off) Controller determination (key on) Controller determination (key off) t3: Key scan execution time when the key data agreed for two key scans. (800 T (s)) t4: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1600 T (s)) 1 T= fOSC t5: Key address (43H) transfer time t6: Key data read time * Explanation In this technique, the controller uses a timer to determine key on/off states and read the key data. The controller must check the DO state when CE is low every t7 period without fail. If DO is low, the controller recognizes that a key has been pressed and executes the key data read operation. The period t7 in this technique must satisfy the following condition. t7 > (t5 + t6 + t4) If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data (SA) will be invalid. 2. Interrupt based key data acquisition * Flowchart Key data read processing Wait for at least t8 No. 5066-23/25 LC75854E, 75854W * Timing chart Key input Key scan Key address Key data read Key data read request Controller determination (key on) Controller determination (key off) Controller determination (key on) Controller determination (key on) Controller determination (key on) Controller determination (key off) t3: Key scan execution time when the key data agreed for two key scans. (800 T (s)) t4: Key scan execution time when the key data did not agree for two key scans and the key scan was executed again. (1600 T (s)) 1 T= fOSC t5: Key address (43H) transfer time t6: Key data read time * Explanation In this technique, the controller uses interrupts to determine key on/off states and read the key data. The controller must check the DO state when CE is low. If DO is low, the controller recognizes that a key has been pressed and executes the key data read operation. After that the next key on/off determination is performed after the time t8 has elapsed by checking the DO state when CE is low and reading the key data. The period t8 in this technique must satisfy the following condition. t8 > t4 If a key data read operation is executed when DO is high, the read key data (KD1 to KD30) and sleep acknowledge data (SA) will be invalid. No. 5066-24/25 LC75854E, 75854W Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of October, 1999. Specifications and information herein are subject to change without notice. PS No. 5066-25/25