H3DE-M2 AC/DC24-230 - Omron Electronics

Multifunction Timer H3DE

Analog Set Multifunction Timers

In Slim 22.5 mm Design

For Track Mounting

HWide AC/DC power supply range

(24 to 230 VAC/DC) minimizes inventory

H12 VDC available in H3DE-M model

HProgrammable contacts (available in

-M2 and -S2 models) can enable and

disable a self-holding relay circuit

HEight operating modes in the H3DE-M

(four in the H3DE-S) offer wide

application flexibility

HTime setting range 0.10 sec to 120 hrs

HFinger protection terminal block

Ordering Information

JTIMER

Description Part number

Contact output Supply voltage Multifunctional Standard

DPDT (time-limit output SPDT);

and switchable SPDT

(

←

→

)

12 VDC H3DE-M2 DC12 —

(

me-

←→

aneous

)

24 to 230

VAC/DC

H3DE-M2 AC/DC24-230 H3DE-S2 AC/DC24-230

SPDT (time-limit output SPDT) H3DE-M1 AC/DC24-230 H3DE-S1 AC/DC24-230

JMODEL NUMBER LEGEND

H3DE-j-j-j

123

1. M: Multifunction type

S: Standard type

2. 1: SPDT

2: DPDT

3. Supply voltage

JACCESSORIES (ORDER SEPARATELY)

Item Description Part number

Mounting track 50 cm (l) x 7.3 mm (t) PFP-50N

1m(l)x7.3mm(t) PFP-100N

1 m (l) x 16 mm (t) PFP-100N2

End plate PFP-M

Spacer PFP-S

H3DEH3DE

Specifications

JGENERAL

Item H3DE-M2 H3DE-M1 H3DE-S2 H3DE-S1

Operating mode A: ON-delay (Signal or Power)

B: Repeat-cycle OFF start (Signal or Power)

B2: Repeat-cycle ON start (Signal or Power)

C: Signal ON-/OFF-delay

D: Signal OFF-delay

E: Interval (Signal or Power)

G: Signal ON-/OFF-delay

J: One-shot (Signal or Power)

A: ON-delay

B2: Repeat-cycle ON start

E: Interval

J: One-shot

Terminal block Clamps two 2.5 mm2max. bar terminals without sleeves.

Terminal screw tightening

torque

0.98 N Sm max. {approx. 10 kgf Scm max.}

Input type Voltage input ---

Output type Relay: DPDT Relay: SPDT Relay: DPDT Relay: SPDT

Mounting method DIN track mounting (See Note.)

Attachment Nameplate

Approved standards UL508, CSA 22.2 No.14

Conforms to EN61812-1, IEC60664-1 (VDE0110) 4 kV/2, VDE0106/P100

Output category according to IEC60947-5-1 (AC-13; 250 V 5A/AC-15; 250 V 3 A/DC-13; 30 V 0.1 A)

Note: Can be mounted to 35-mm DIN track with a plate thickness of 1 to 2.5 mm.

JTIME RANGES

Time scale display Time unit display

seconds min hrs 10 h

x0.1 0.1to1.2s 0.1to1.2min 0.1to1.2h 1to12h

x1 1to12s 1to12min 1to12h 10 to 120 h

Note: When the main dial is set to “0” for all settings, the output will operate instantaneously.

JRATINGS

Rated supply voltage

(See Notes 1 and 2.)

24 to 230 VAC/DC (50/60 Hz)

12 VDC (H3DE-M2 model only)

Operating voltage range 85% to 110% of rated supply voltage

Power reset Minimum power-off time: 0.1 s

Reset voltage 2.4 VAC/DC max.

Power

consumption

(

)

H3DE-M1 AC: approx. 4.3 VA (2.2 W) at 230 VAC

DC: approx. 0.7 W at 24 VDC

(See Note 3.) H3DE-M2 AC: approx. 4.8 VA (2.4 W) at 230 VAC

DC: approx. 1.0 W at 24 VDC

H3DE-S1 AC: approx. 2.7 VA (1.6 W) at 230 VAC

DC: approx. 0.7 W at 24 VDC

H3DE-S2 AC: approx. 3.2 VA (1.9 W) at 230 VAC

DC: approx. 1.0 W at 24 VDC

Voltage input Max. permissible capacitance between input lines (terminals B1 and A2) : 2000 pF

Load connectable in parallel with inputs (terminals B1 and A2)

H-level: 20.4 to 253 VAC/DC

L-level: 0 to 2.4 VAC/DC

Control output Contact output: 5 A at 250 VAC with resistive load (cosφ= 1); 5 A at 30 VDC with resistive

load (cosφ=1)

Ambient temperature Operating: --10°Cto55°C (14 to 131°F) with no icing

Storage: --25°Cto65°C(--13°F to 149°F) with no icing

Ambient humidity Operating: 35% to 85%

Note: 1. DC ripple rate: 20% max.

2. Since an inrush current of 0.25 A will occur when using the power supply voltage at 24 VDC, pay careful attention when turning

on or off the power supply to the Timer with a solid-state output such as a sensor.

3. The power consumption is for mode A (ON-delay) after the Timer counts the time-up time and for the AC input at 50 Hz. The

power consumption of the H3DE-Mjincludes the input circuit with the B1 and A1 terminals short-circuited.

H3DEH3DE

JCHARACTERISTICS

Accuracy of operating time ±1% max. of FS (±1% ±10 ms max. at 1.2-s range) (See Note 1.)

Setting error ±10% ±50 ms max. of FS (See Note 1.)

Signal input time 50 ms min. (See Note 1.)

Voltage influence ±0.5% max. of FS (±0.5% ±10 ms max. at 1.2-s range)

Temperature influence ±2% max. of FS (±2% ±10 ms max. at 1.2-s range)

Insulation resistance 100 MΩmin. at 500 VDC

Dielectric strength Between current-carrying metal parts and exposed non-current-carrying metal parts: 2,000 VAC for 1 min.

Between control output terminals and operating circuit: 2,000 VAC for 1 min.

Between contacts of different polarities: 2,000 VAC for 1 min.

Between contacts not located next to each other: 1,000 VAC for 1 min.

Vibration resistance Malfunction: 0.5-mm single amplitude at 10 to 55 Hz

Destruction: 0.75-mm single amplitude at 10 to 55 Hz

Shock resistance Malfunction: 100 m/s2(approximately 10G)

Destruction: 1,000 m/s2(approximately 100G)

Contact material AgNi+goldplating(UsetheG6RN-1at12VDC.)

Impulse withstand voltage 3 kV (between power terminals)

4.5 kV (between current-carrying metal parts and exposed non-current-carrying metal parts)

Noise immunity Square-wave noise generated by noise simulator (pulse width: 100 ns/1 µs, 1-ns rise) ±1.5 kV

Static immunity Malfunction: 4 kV

Destruction: 8 kV

Life expectancy Mechanical: 10 million operations min. (under no load at 1,800 operations/h)

Electrical: 100,000 operations min. (5 A at 250 VAC, resistive load at 360 operations/h)

(See Note 2.)

EMC EMI

Emission Enclosure: EN55011 Group 1 class A

Emission AC Mains: EN55011 Group 1 class A

Harmonic Current: EN61000-3-2

Voltage Fluctuation and Flickering EN61000-3-3

EMS

Immunity ESD: EN61000-4-2: 6 kV contact discharge (level 3);

8 kV air discharge (level 3)

Immunity RF-interference from AM Radio Waves: EN61000-4-3: 10 V/m (80 MHz to 1 GHz) (level 3)

Immunity Burst: EN61000-4-4: 2 kV power port and output port (level 3);

1 kV control port with capacitive clamp (level 3)

Immunity Surge: EN61000-4-5: 2 kV common mode (level 3);

1 kV differential mode (level 3)

Enclosure rating IP30 (Terminal block: IP20)

Weight 120 g

Note: 1. With the H3DE-Mj, if the voltage exceeds 26.4 VAC/DC, the following hold at signal OFF for C, D, and G modes:

Accuracy of operating time: ±1% ±50 ms max. at 1.2-s range

Setting error: ±10% +100/--50 ms max.

Signal input time: 100 ms min.

2. For reference : A maximum current of 0.15 A can be switched at 125 VDC (cosφ=1).

A maximum current of 0.1 A can be switched if L/R is 7 ms.

In both cases, a life of 100,000 operations can be expected.

The minimum applicable load is 10 mA at 5 VDC (failure level: P).

H3DEH3DE

Nomenclature

Output type selector switch for

H3DE-M2/-S2 (default setting

is time-limit output)

Setting Output type

Time-limit output (terminal numbers 25, 26 and

28) (default setting)

Instantaneous output

(terminal numbers 21, 22 and 24)

Output Type Selector Switch Settings

Output indicator (orange)

(Lit while Timer gives output.)

Operating mode selector

(select a mode from A, B, C,

B2,D,E,J,andGforthe

H3DE-M1/-M2, from A, E, J,

and B2 for the H3DE-S1/S2)

Power-on indicator (green)

(Lit while the power is on.)

Nameplate (20 x 5.4 mm white panel)

Time unit selector (select one from

sec, min, hrs, and 10 h)

Main dial (for setting a time value)

Time scale selector

(select 0.1 or 1)

Time scale indicator Time unit display window

Operating mode display window

JH3DE-F

Front View

Bottom View

H3DEH3DE

Operation

JBLOCK DIAGRAM

H3DE-M1/-M2

AC (DC) input

Power supply

circuit

Zero setting

detection

circuit

Oscillation

circuit

Time range/

unit selectors

Counting

circuit

Operating

mode selector

Output circuit

Indicator

circuit

Power-ON

indicator

Output

indicator

Start input Input circuit

AC (DC) input

Power supply

circuit

Zero setting

detection

circuit

Oscillation

circuit

Time range/

unit selectors

Counting

circuit

Operating

mode selector

Output circuit

Indicator

circuit

Power-ON

indicator

Output

indicator

H3DE-S1/-S2

JI/O FUNCTIONS

Item H3DE-M1/-M2 H3DE-S1/-S2

Input Start Starts operation. No input is available.

Output Control output Outputs are turned ON according to designated output mode when preset value is reached. (See Note.)

Note: When the output type selector switch on the bottom of the Timer is set to the instantaneous side, the relay R2 (terminal numbers

21/25, 22/26, and 24/28) becomes an instantaneous contact and turns ON/OFF in synchronization with the changes in the power

supply.

H3DEH3DE

JBASIC OPERATION

Selector Setting

The selectors can be turned clockwise and counterclockwise to

select the desired time unit, time scale, or operating mode.

Each selector has a snap mechanism that secures the selector at

a given position. Set the selector at a position at which it is

secured. Do not set it midway between two securing positions or

a malfunction could result from improper setting.

Operating mode selector

Groove for

screwdriver

Operating mode

display window

Operating Mode Selection

The H3DE-M/-S can be set to any one of the operating modes A

to J. Turn the operating mode selector with a screwdriver until the

desired operating mode (A, B, B2, C, D, E, G, or J for the

H3DE-M and A, B2, E, or J for the H3DE-S) appears in the

operating mode display window located below the selector.

Time Unit and Time Scale Selection

The desired time unit (sec, min, hrs, or 10h) can be displayed in

the time unit display window above the time setting dial by

turning the time unit selector located at the upper right corner of

the front panel. The time scale (0.1 or 1) is selected with the time

scale selector at the upper left corner of the front panel. It

appears in the scale range display window above the selector.

Scale range

selector

Scale range display

window

Time unit selector

Time unit display window

JTIMING CHART

Note: 1. The minimum power reset time is 0.1 s and the minimum signal input time is 0.05 s.

2. The letter “t” in the timing charts stands for the set time and “t--a” means that the period is less than the time set.

Operating

mode

Timing chart

A: ON-delay tt

Power (A1and A2)

Output relay: NC

15 and 16

(25 and 26)

Start (B1and A2)

(See Note.)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

t--a

Power indicator

Power

Start

Output

Basic operation

* For power-on operation, impose voltage to the

Start input. The Timer starts operating at the

moment the power is turned on.

** Start input is invalid while the Timer is in opera-

tion.

***

(This table continues on the next page.)

H3DEH3DE

Timing Chart — continued from previous page

Operating

mode

Timing chart

Repeat-

cycle OFF

start Basic operation

Power

Start

Output

t t t t

ttt--a t t t t--a

Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

* For power-on operation, impose voltage to the

Start input. The Timer starts operating at the

moment the power is turned on.

** Start input is invalid while the Timer is in opera-

tion.

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

***

B2:

Repeat-

cycle ON

start Basic operation

Power

Start

Output

t t t t

Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

ttt t -- a t t t -- a

* For power-on operation, impose voltage to the

Start input. The Timer starts operating at the

moment the power is turned on.

** Start input is invalid while the Timer is in opera-

tion.

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

***

Signal

ON/OFF-

delay

Basic operation

Power

Start

Output

tt tt

Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

t t t--a t--a

* Start input is invalid while the Timer is in opera-

tion.

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

Note: The start input of the H3DE-M1 or H3DE-M2 model is activated by applying a voltage to B1 and A2 terminals.

The voltage can be applied by turning on the contact between B1 and A1 (Refer to Terminal Arrangement).

(This table continues on the next page.)

H3DEH3DE

Timing Chart — continued from previous page

Operating

mode

Timing chart

Signal

OFF-delay Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

tt t -- a t -- a t t -- a

Basic operation

Power

Start

Output

* Start input is valid and re-triggerable while the

Timer is in operation.

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

E: Interval

Power

Start

Output

Basic operation

t--a

Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

tt--a

* For power-on operation, impose voltage to the

Start input. The Timer starts operating at the

moment the power is turned on.

** Start input is valid and re-triggerable while the

Timer is in operation.

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

***

Signal

ON/OFF-

delay Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

Power

Start

Output

Basic operation

* Start input is valid and re-triggerable while the

Timer is in operation.

t t t t

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

One-shot

output

(ON delay) Power (A1and A2)

Start (B1and A2)

(See Note.)

Power indicator

Power

Start

Output

Basic operation

* For power-on operation, impose voltage to the

Start input. The Timer starts operating at the

moment the power is turned on.

** Start input is valid and re-triggerable while the

Timer is in operation.

tt tt--a t--a

Approx.

1±0.6 s

(fixed)

Approx.

1±0.6 s

(fixed)

Approx.

1±0.6 s

(fixed)

t Approx. 1±0.6 s

(fixed)

Output relay: NC

15 and 16

(25 and 26)

Output relay: NO

(output indicator)

15 and 18

(25 and 28)

***

Note: The start input of the H3DE-M1 or H3DE-M2 model is activated by applying a voltage to B1 and A2 terminals.

The voltage can be applied by turning on the contact between B1 and A1 (Refer to Terminal Arrangement).

H3DEH3DE

Dimensions

Unit: mm (inch)

JH3DE-M

H3DE-S

(2.95)

100

(3.94)

Terminal block (black)

Surface color: 5Y7/1 (OMRON)

Output type selector switch (default setting: Time-limit output)

Terminal block (black)

(3.11)

36.9

12.7

7°

22.5

(0.89)

Installation

JTERMINAL ARRANGEMENT

25/2115

R1 R2

(See Note 1.)

18 16

18 16 A2

28/24 26/22

A1 15 25/21

25/2115

R1 R2

(See Note 1.)

18 16

18 16 A2

28/24 26/22

A1 15 25/21

H3DE-M1 H3DE-S1H3DE-M2 H3DE-S2

18 16

18 16 A2

A1 15

18 16

18 16 A2

A1 15

(See Note 2.)

-------------------------------------------------

------------

-------------------------------------------------

------------

-------------------------------------------------

(See Note 2.) (See Note 2.) (See Note 2.)

Note: 1. The contact symbol for the H3DE is indicated with because it offers multiple operating modes and is different from

the delayed contact for conventional timers.

2. DC supply voltage does not require the designation of polarity.

3. The relay R2 can be set to either instantaneous or time-limit contact using the switch located on the bottom of the Timer.

H3DEH3DE

JINPUT CONNECTIONS

The inputs of the H3DE-M1/-M2 are voltage (voltage imposition or open) inputs.

No-Contact Input

Connection to PNP output sensor. Contact Input

Sensor

Start

24 VDC

Start

Operates with PNP transistor ON Operates with relay ON

TimerTimer

No-Contact Input

Connection to NPN output sensor.

(+)

(--)

Sensor

24 VDC

(+)

(--)

Operates with NPN transistor ON

Timer

Voltage Input Signal Levels

No-contact input 1. Transistor ON

Residual voltage: 1 V max.; voltage between terminals B1and A2must be more than the rated

“H-level” voltage (20.4 VDC min.)

2. Transistor OFF

Leakage current: 0.01 mA max.; voltage between terminals B1and A2must be less than the

rated “L-level” voltage (2.4 VDC max.)

Contact input Use contacts that can adequately switch 0.1 mA at each voltage to be imposed. When the

contacts are ON or OFF, voltage between terminals B1and A2must be within the following

ranges. When contacts are ON: 20.4 to 253 VAC/DC. When contacts are OFF: 0 to 2.4

VAC/DC

H3DEH3DE

Accessories (Order Separately)

Mounting Track PFP-100N, PFP-50N PFP-100N2

L: Length

End Plate PFP-M Spacer PFP-S

4.5

15 25 25 25 25 *

10 10

7.3±0.15

35±0.3 27±0.15

4.5

15 25 25 25 25 15

10 10

35±0.3 27 24

29.2

11.5

M4 x 8

pan head

screw

6.2 1.8

35.5

1.8

1.3

(0.63)

34.8

(1.37)

50 cm

1m 39.37 in PFP-100N2

PFP-100N

39.37 in

19.69 in PFP-50N

(1.97)

11.5

(0.45)

35.3

(1.39)

4.8

(0.19)

44.3

(1.74)

16.5

(0.65)

Unit: mm (inch)

JDIMENSIONS

Precautions

JSETTING CHANGES

Note: Important: Do not change the time unit, time scale,

operating mode, or output type selector switch while the

Timer is in operation.

JMOUNTING AND REMOVAL

The H3DE should be mounted as horizontally as possible.

When mounting the H3DE on a socket mounting track, hook

portion (A) of the Timer to an edge of the track first, and then

depress the Timer in the direction of (B).

(A)

(B)

When removing the H3DE, pull out portion (C) with a flat-blade

screwdriver and remove the Timer from the mounting track.

Rail stopper

The H3DE can be mounted or removed easily if a distance of

30 mm (1.18 in) or more is kept between the H3DE and the top

surface of other equipment located below the H3DE.

H3DEH3DE

JPOWER SUPPLIES

The H3DE Series is provided with a transformerless power

supply system. An electric shock may be received if the input

terminal or the output type selector switch is touched while power

is being supplied.

Use the bar terminal for wiring the H3DE. Using a stranded-wire

terminal may cause a short-circuit due to a stray wire entering

into the Timer.

Both AC and DC power supplies can be connected to the power

input terminals without regarding polarity.

With the H3DE only, a DC power supply must be connected to

the power input terminals as designated according to the polarity

of the terminals.

A DC power supply can be connected if its ripple factor is 20% or

less and the mean voltage is within the rated operating voltage

range of the Timer.

Connect the power supply voltage through a relay or switch in

such a way that the voltage reaches a fixed value at once or the

Timer may not be reset or a timer error could result.

For the power supply of an input device, use an isolating

transformer, of which the primary and secondary windings are

mutually isolated and the secondary winding is not grounded.

H3DE Power supply

Circuit

Isolation transformer is required.

Rectifier circuit

Start

input

JMOUNTING CLEARANCE

If the load current is continuously being supplied to the Timer for

a long period of time, be sure to provide the mounting clearance

as shown in the figure below. If used under the conditions other

than those specified below, the life of internal components may

be shortened due to an excessive rise in the internal

temperature.

DIN track

t: Mounting clearance (mm)

H3DE H3DE H3DE

JSWITCHING CURRENT VS.

AMBIENT TEMPERATURE

(WHEN MOUNTING TWO OR MORE

H3DE UNITS SIDE-BY-SIDE)

Ambient temperature ( C)

01 2 34 5

Load current (A)

Mounting

clearance: 0 mm

Mounting

clearance: 5 mm

Mounting

clearance: 10 mm

Maximum range of

operating ambient

temperature

Mounting clearance:

50 mm min.

Note: Measurement Condition: Input voltage of 230 VAC.

H3DEH3DE

JINPUT/OUTPUT

Relationship between Input and

Power Supply Circuits

Input circuit Power supply

circuit

AC/DC

power

supply

A1B1

Since the input circuit and the power supply circuit are configured

independently, the input circuit can be turned on or off

irrespective of the on/off state of the power supply.

It must be noted that a voltage equivalent to the power supply

voltage is applied to the input circuit.

When connecting a relay or a transistor as an external signal

input device, pay attention to the following points to prevent

short-circuiting due to a sneak current to the transformerless

power supply.

If a relay or transistor is connected to two or more Timers, the

input terminals of those Timers must be wired properly so that

they will not be different in phase or the terminals will be

short-circuited to one another (refer to the figures below).

Incorrect

Contact or transistor for external input signal

Correct

H3DE Power supply

H3DE

Short-circuit

current

Contact or transistor for external input signal

H3DE Power supply

H3DE

Short-circuit

current

Note: The H3DE Series is provided with a transformerless pow-

er supply system.

JINPUT WIRES

The input wires must be as short as possible. If the floating

capacity of wires exceeds 2,000 pF (approx. 17 m for cables with

120 pF/m), the operation will be affected. Pay particular attention

when using shielded cables.

JVDE CONFORMANCE

The H3DE as a built-in timer conforms to VDE 0435/P2021

provided that the following conditions are satisfied:

The output section of the H3DE is provided only with basic

isolation. To ensure reinforced isolation required by the VDE

standards, provide supplementary basic isolation on the load side

connected to the output.

The H3DE itself is designed according to the following:

•Overvoltage category III

•Pollution degree 2

The following facts are based on the above standards:

•Operation parts on the front and bottom: Reinforced isolation

with clearance of 5.5 mm and creepage distance of 5.5 mm

at 230 VAC

•Output: Basic isolation with clearance of 3 mm and creepage

distance of 3 mm at 230 VAC

H3DEH3DE

JENVIRONMENT

When using the Timer in an area with excess electronic noise,

separate the Timer, wiring, and the equipment which generates

the input signals as far as possible from the noise sources. To

further prevent electronic interference, shield the input signal

wiring.

Organic solvents (such as paint thinner), as well as very acidic or

basic solutions can damage the outer casing of the Timer.

Do not use the Timer in places where it is exposed to dust,

corrosive gas, or direct sunlight.

When storing the Timer, make sure that the ambient temperature

and humidity are within the rated values. Leave the Timer at

room temperature for at least three hours before using the Timer

if it has been stored at an ambient temperature of --10°Cor

below.

JRELAY LIFE EXPECTANCY

Built-in relay for the H3DE: G6RN; 50,000 operations min.

(8 A at 250 VAC, resistive load at 360 operations/h.)

Cat. No. GC TMCN1 3/02 Specifications subject to change without notice. Printed in U.S.A.

OMRON ELECTRONICS LLC

OneEastCommerceDrive

Schaumburg, IL 60173

NOTE: DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters to inches divide by 25.4.

1-800-55-OMRON

OMRON CANADA, INC.

885 Milner Avenue

Scarborough, Ontario M1B 5V8

416-286-6465

OMRON ON--LINE

Global -- http://www.omron.com

USA -- http://www.omron.com/oei

Canada -- http://www.omron.com/oci