A22TK-2LL-02-K01 - OMRON - Datasheet.Directory

Safety Key Selector Switch

A22TK

Key-type Selector Switch with Direct

Opening Mechanism

• Selector Switch for secure equipment activation during

maintenance

• 30 types of exclusive keys make it more difficult to disable.

• The key has the same shape as the following keys.

- The key of the A22LK Guard Lock Safety Key Selector Switch

- The trapped key of the D4JL Guard Lock Safety-door Switch

-The lockout key of the D4JL-NSK10-LK and D4GL-SK10-LK Slide Key

Units

• Common to the switch part of Emergency Stop Switch A22E.

(Non-lighted model only)

Features

Because the A22TK Safety Key Selector Switch uses the same key as the Guard Lock Safety-door Switch, the operator is prevented from forgetting

to remove the key. The result is a safer working environment when performing maintenance.

Be sure to read the "Safety Precautions" on page 12.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Broad range of applications include use with door locks, mode switching, and emergency stops when teaching

Common Key for Door Switch and Selector Switch

With the Selector Switch, it is possible to

switch between normal operation mode

(use of Door Switch is available) and

maintenance mode (use of Enabling

Grip Switch is available).

A22TK

Safety Key

Selector Switch

Safety Key

Selector Switch

Guard Lock

Safety-door Switch

Guard Lock

Safety-door Switch

G9SX-GS

Safety Controllers

such as Safety Guard

Switching Unit

A4EGD4GL-SK10-LK@

D4SL-NSK10-LK@

A22TK

Enabling

Grip Switch

D4JL

D4GL-SK10-LK@

D4SL-NSK10-LK@

Common Key

* To unify keys, specify the same key type.

A22TK

Key: Cannot be removed

I take the key with me when

I enter, so there is no worry

of becoming trapped inside!

Guard Lock

Safety-door Switch

Safety can be ensured, but there is a risk of human error

occurring during operation.

By using a common key, the risk of human error is reduced in operations

from when the door is open/shut until the equipment is started.

From

When only the Door Switch is used, the operator is at risk of being

shut inside the barrier if, for example, he/she forgets to remove the

trapped key and a third party locks the door.

The equipment may also be started up while the operator is inside.

The two locks on the door and equipment use the same key, reducing the likelihood that the user will forget to remove it.

In addition, the key cannot be removed when maintenance is being performed. This prevents the key from being lost and greatly

reduces the risk of an operator becoming trapped inside.

Forgetting to

remove the key

Assumed risks

Being

trapped inside Forgetting to

remove the key Being

trapped inside

Assumed risks

Starting equipment

Guard Lock Safety-door Switch only

The safety level is enhanced by switching to maintenance mode.

However, because two different types of keys are required,

the operator is still at risk of being shut inside if he/she forgets to

remove the trapped key.

Guard Lock Safety-door Switch Key Selector Switch (A22K)

Guard Lock Safety-door Switch Safety Key Selector Switch (A22TK)

I should close it.I should close it.

I'm trapped

inside!

The equipment

started up!

Operation starts

Common key

Furthermore

Different keys

Lock the door

End maintenance

Start maintenance

Operation stopped

RUN

MAINTENANCE

Key: Can be removed

LOCKUNLOCK

RUN

MAINTENANCE

Key: Can be removed

Unlock the door

Operation stopped

Operation double-stopped

Key: Cannot be removed

LOCKUNLOCK

Same Key

A22TK

A22TKD4JL

D4JL

Safety Key

Selector Switch

A22TK

Enabling Grip Switch Safety Laser Scanner

during maintenance and by using a By using the to detect

the presence of operators, equipment malfunctions can be prevented when operators are inside, enabling a higher safety level.

or Safety Mat

A22TK

Model Number Structure

Model Number Legend (Ordering as a set)

The Operation Unit and Switch are delivered as a set. For information on combinations, refer to Ordering Information

on page 5.

The models numbers of only Operation Units are they same as the set model numbers without (2) Contact

Configuration.

Example: The model number of the Operation Unit from the A22TK-2LL-12-K01 Set is A22TK-2LL-K01.

Ask your OMRON representative about parts without model numbers when ordering.

(1) (2) (3) (4)

A22TK- 2LL - 12 - K 01

(1) Operation Unit

Symbol No. of

notches Key release position

Key position of NC contact closing

2LL

2RL

2LR

2RR

(3) Key Availability

Symbol Type

None No key

KWith key

(4) Key Type

01 to 30: 30 types *

(2) Contact Configuration

Symbol Type

01 SPST-NC

11 SPST-NO/SPST-NC

02 DPST-NC

12 DPST-NC + SPST-NO

21 DPST-NO + SPST-NC

03 TPST-NC

* Key can be created up to 30 types. Specify keys in

order starting from 01.

Key drop preventive type

A22TK-@-@-@01-SJ

―

――

(1) (2) (3)

(1) Operation Unit

Symbol No. of

notches Key release position

Key position of NC

contact closing

2LL

2RL

2LR

2RR

(3) Key Availability

Symbol Type

None No key

KWith key

(2) Contact Configuration

Symbol Type

01 SPST-NC

11 SPST-NO/SPST-NC

02 DPST-NC

12 DPST-NC+SPST-NO

21 DPST-NO+SPST-NC

03 TPST-NC

A22TK

Key drop preventive (on the A22TK-2RL-@)

Contact Configuration

A22TK-2@L

A22TK-2@R

Operation Angle

*1. If the key is stopped at a position between FP and TTP, the contacts will not be in the states indicated above.

Always be careful to turn the key completely to the FP (HP) or TTP position to ensure that the contacts are properly switched and the direct

open circuit operation characteristics are obtained.

*2. Key drop preventive type (A22TK-@-SJ or A22TK-@-SJ only)

Key position SPST-NC SPST-NO/SPST-NC DPST-NC DPST-NC + SPST-NO DPST-NO + SPST-NO TPST-NC

Operating rangeOperating range

NC contact: ON

Key: Hold

NC contact: OFF

Key: Removed

NC contact: ON

Key: Hold

NC contact: OFF

Key: Removed

NC contact: OFF

Key: Hold

Key drop preventive typeStandard type

TTP 90° FP

90°

15° 15°

＊1 ＊1

＊2＊2

FP : Free position

TTP

: Total travel position

HP　: Key hold position (drop prevention) *2

A22TK-2L@

A22TK-2L@-SJ

A22TK-2R@

A22TK-2R@-SJ

A22TK

Ordering Information

Switch

List of Models (Completely Assembled)... Shipped as a set which includes the Operation Unit and Switch.

The models numbers of only Operation Units are they same as the set model numbers without (2) Contact Configuration.

Example: The model number of the Operation Unit from the A22TK-2LL-12-K01 Set is A22TK-2LL-K01.

Ask your OMRON representative about parts without model numbers when ordering.

Appearance Key release

position

Key position of NC

contact closing Contact Configuration Key

availability Model

SPST-NC

Yes

A22TK-2LL-01-K01

SPST-NO/SPST-NC A22TK-2LL-11-K01

DPST-NC A22TK-2LL-02-K01

DPST-NC + SPST-NO A22TK-2LL-12-K01

DPST-NO + SPST-NC A22TK-2LL-21-K01

TPST-NC A22TK-2LL-03-K01

SPST-NC A22TK-2RL-01-K01

SPST-NO/SPST-NC A22TK-2RL-11-K01

DPST-NC A22TK-2RL-02-K01

DPST-NC + SPST-NO A22TK-2RL-12-K01

DPST-NO + SPST-NC A22TK-2RL-21-K01

TPST-NC A22TK-2RL-03-K01

SPST-NC A22TK-2LR-01-K01

SPST-NO/SPST-NC A22TK-2LR-11-K01

DPST-NC A22TK-2LR-02-K01

DPST-NC + SPST-NO A22TK-2LR-12-K01

DPST-NO + SPST-NC A22TK-2LR-21-K01

TPST-NC A22TK-2LR-03-K01

SPST-NC A22TK-2RR-01-K01

SPST-NO/SPST-NC A22TK-2RR-11-K01

DPST-NC A22TK-2RR-02-K01

DPST-NC + SPST-NO A22TK-2RR-12-K01

DPST-NO + SPST-NC A22TK-2RR-21-K01

TPST-NC A22TK-2RR-03-K01

SPST-NC

A22TK-2LL-01-01

SPST-NO/SPST-NC A22TK-2LL-11-01

DPST-NC A22TK-2LL-02-01

DPST-NC + SPST-NO A22TK-2LL-12-01

DPST-NO + SPST-NC A22TK-2LL-21-01

TPST-NC A22TK-2LL-03-01

SPST-NC A22TK-2RL-01-01

SPST-NO/SPST-NC A22TK-2RL-11-01

DPST-NC A22TK-2RL-02-01

DPST-NC + SPST-NO A22TK-2RL-12-01

DPST-NO + SPST-NC A22TK-2RL-21-01

TPST-NC A22TK-2RL-03-01

SPST-NC A22TK-2LR-01-01

SPST-NO/SPST-NC A22TK-2LR-11-01

DPST-NC A22TK-2LR-02-01

DPST-NC + SPST-NO A22TK-2LR-12-01

DPST-NO + SPST-NC A22TK-2LR-21-01

TPST-NC A22TK-2LR-03-01

SPST-NC A22TK-2RR-01-01

SPST-NO/SPST-NC A22TK-2RR-11-01

DPST-NC A22TK-2RR-02-01

DPST-NC + SPST-NO A22TK-2RR-12-01

DPST-NO + SPST-NC A22TK-2RR-21-01

TPST-NC A22TK-2RR-03-01

A22TK

Accessories

Note: For information on two-hole and three-hole control boxes, contact your OMRON representative.

The Switch Block, Mounting Latch, Connector, and Lock Plate of A22E can be used.

Appearance Key release

position

Key position of NC

contact closing Contact Configuration Key

availability Model

SPST-NC

Yes

A22TK-2LL-01-K01-SJ

SPST-NO/SPST-NC A22TK-2LL-11-K01-SJ

DPST-NC A22TK-2LL-02-K01-SJ

DPST-NC + SPST-NO A22TK-2LL-12-K01-SJ

DPST-NO + SPST-NC A22TK-2LL-21-K01-SJ

TPST-NC A22TK-2LL-03-K01-SJ

SPST-NC A22TK-2RL-01-K01-SJ

SPST-NO/SPST-NC A22TK-2RL-11-K01-SJ

DPST-NC A22TK-2RL-02-K01-SJ

DPST-NC + SPST-NO A22TK-2RL-12-K01-SJ

DPST-NO + SPST-NC A22TK-2RL-21-K01-SJ

TPST-NC A22TK-2RL-03-K01-SJ

SPST-NC A22TK-2LR-01-K01-SJ

SPST-NO/SPST-NC A22TK-2LR-11-K01-SJ

DPST-NC A22TK-2LR-02-K01-SJ

DPST-NC + SPST-NO A22TK-2LR-12-K01-SJ

DPST-NO + SPST-NC A22TK-2LR-21-K01-SJ

TPST-NC A22TK-2LR-03-K01-SJ

SPST-NC A22TK-2RR-01-K01-SJ

SPST-NO/SPST-NC A22TK-2RR-11-K01-SJ

DPST-NC A22TK-2RR-02-K01-SJ

DPST-NC + SPST-NO A22TK-2RR-12-K01-SJ

DPST-NO + SPST-NC A22TK-2RR-21-K01-SJ

TPST-NC A22TK-2RR-03-K01-SJ

SPST-NC

A22TK-2LL-01-01-SJ

SPST-NO/SPST-NC A22TK-2LL-11-01-SJ

DPST-NC A22TK-2LL-02-01-SJ

DPST-NC + SPST-NO A22TK-2LL-12-01-SJ

DPST-NO + SPST-NC A22TK-2LL-21-01-SJ

TPST-NC A22TK-2LL-03-01-SJ

SPST-NC A22TK-2RL-01-01-SJ

SPST-NO/SPST-NC A22TK-2RL-11-01-SJ

DPST-NC A22TK-2RL-02-01-SJ

DPST-NC + SPST-NO A22TK-2RL-12-01-SJ

DPST-NO + SPST-NC A22TK-2RL-21-01-SJ

TPST-NC A22TK-2RL-03-01-SJ

SPST-NC A22TK-2LR-01-01-SJ

SPST-NO/SPST-NC A22TK-2LR-11-01-SJ

DPST-NC A22TK-2LR-02-01-SJ

DPST-NC + SPST-NO A22TK-2LR-12-01-SJ

DPST-NO + SPST-NC A22TK-2LR-21-01-SJ

TPST-NC A22TK-2LR-03-01-SJ

SPST-NC A22TK-2RR-01-01-SJ

SPST-NO/SPST-NC A22TK-2RR-11-01-SJ

DPST-NC A22TK-2RR-02-01-SJ

DPST-NC + SPST-NO A22TK-2RR-12-01-SJ

DPST-NO + SPST-NC A22TK-2RR-21-01-SJ

TPST-NC A22TK-2RR-03-01-SJ

Name Appearance Classification Model Remarks

Control Box One hole, yellow box

A22Z-B101Y

Material: Polycarbonate resin

The A22Z-B101Y do not support 2NO, 2NC,

or 1NO + 1NC One-piece Switch Blocks. The

A22Z-B201Y do not support A22-series

Alternate-action Switches. They also do not

support 2NO, 2NC, or 1NO + 1NC One-piece

Switch Blocks.

A22Z-B201Y

A22TK

Specifications

Approved Standard Ratings

• UL, cUL (File No. E41515): 6 A at 220 VAC, 10 A at 110 VAC

• TÜV (EN60947-5-1) (Low Voltage Directive): 3 A at 220 VAC

• CCC (GB/T 14048.5): 3 A at 240 VAC, 1.5 A at 24 VDC

Certified Standards

Note: Only models with NC contacts have a direct opening

mechanism.

*1. UL-certification for CSA C22.2 No. 14 has been obtained.

(Certification has been obtained for the Switch Unit only)

Ratings

Contacts (Standard load)

Note: 1. Rated current values are determined according to the

testing conditions. The above ratings were obtained by

conducting tests under the following conditions.

(1) Ambient temperature: 20±2C°

(2) Ambient humidity: 65±5% RH

(3)Operating frequency: 20 operations/minute

2. Minimum applicable load: 10 mA at 5 VDC

Characteristics

*1. Malfunction within 1 ms.

*2. With no icing or condensation.

*3. The degree of protection from the front of the panel.

Note: 1. Do not allow the load current to exceed the rated value.

2. The contact ON/OFF timing is not synchronized. Confirm

performance before application.

3. Once the contacts have been used to switch a load,

however, they cannot be used to switch smaller loads. The

contact surfaces will become rough once they have been

used and contact reliability for smaller loads may be

reduced.

Structure and Nomenclature

Certification body Standards File No.

UL *1 UL508, C22.2 No.14 E41515

TÜV SÜD

EN60947-5-1

(certified direct opening

mechanism) Consult your OMRON

representative for

details.CQC(CCC) GB/T 14048.5

KOSHA EN60947-5-1

Rated

carry

current

(A)

Rated

voltage

(V)

Rated current (A)

AC15

(inductive

load)

AC12

(resistive

load)

DC13

(inductive

load)

DC12

(resistive

load)

24 VAC 10 10

110 5 10

220 3 6

380 2 3

440 1 2

24 VDC

1.5 10

110 0.5

220 0.2

0.6

380 0.1

0.2

Item Model A22TK

Allowable

operating

frequency

Mechanical 30 operations/minute max.

Electrical 30 operations/minute max.

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric

strength

Between terminals of

same polarity

2,500 VAC, 50/60 Hz for 1

min.

Between each

terminal and ground

2,500 VAC, 50/60 Hz for 1

min.

Vibration resistance *1 10 to 55 Hz, 1.5-mm double

amplitude (within 1 ms)

Shock

resistance

Destruction 1000 m/s2

Malfunction *1 250 m/s2 max.

Durability Mechanical 100,000 operations min.

Electrical 100,000 operations min.

Ambient operating temperature *2 -20 to +70°C

Ambient operating humidity 35% to 85%RH

Ambient storage temperature -40 to +70°C

Degree of protection IP65 *3

Electric shock protection class Class II

PTI (tracking characteristic) 175

Degree of contamination 3 (EN60947-5-1)

Key * Two keys are provided.

Contact Ratings

10 A at 110 VAC (resistive load)

10 A at 24 VDC (resistive load)

Contact Configuration

SPST-NC, SPST-NO/SPST-NC, DPST-NC, DPST-NC + SPST-NO, DPST-NO + SPST-NC, and TPST-NC

Switch

Lock Plate (attached with the Switch)

(Refer to "Mounting the Lock Plate" on page 13 for use.)

(The above figures are examples of the model with key.)

Operation Unit

A22TK

Dimensions (Unit: mm)

●Switch

●Accessories

Terminal Arrangement (Bottom View)

Terminal Connection

2 Contacts 3 Contacts

Type Terminal connection (Bottom View)

SPST-NO/SPST-NC DPST-NC DPST-NC + SPST-NO DPST-NO + SPST-NC TPST-NC

Non-lighted

Key

5.9

Lock Plate (included)

(A22Z-3380)

10.9

0.5

54.7

16.5

32.6

32.2

30 dia.

29.5 dia.

27 dia.

Key

5.9

Lock Plate (included)

(A22Z-3380)

10.9

0.5

30 dia.

29.5 dia.

27 dia.

54.7

16.5

32.6

32.2

A22TK-2LL A22TK-2RL

4-4 × 38 tapping screw

22.1±0.3

0.1 dia.

10 (10 × 36) 0.6 depression

20.5±0.1

2.8±0.1

Two, 21 dia.

Side lead draw-out hole

69.5

Control Box

A22Z-B101Y (1 hole)

16±1 dia.

(Side lead draw-out hole) 32

Two, mounting holes

Cable Draw-out Hole (Top View)

Mounting Hole

6.3

2-R3

4.3

Four, M4 Screws

22.1±0.3

0.1 dia.

10 (10 × 36) 0.6 depression

20.5±0.1

2.8±0.1

Two, 21 dia.

Side lead draw-out hole

30.5

Two, 19±1 dia.

(Side lead draw-out hole) 40

Mounting Hole

6.3

2-R3

4.3

Cable Draw-out Hole (Top View)

Two, mounting holes

Control Box

A22Z-B201Y (1 hole)

OPEN

LOC

20.7

16.7

Switch blocks

M3.5 screws

OPEN

LOC

16.7

Switch blocks

A22TK

Installation

Mounting to the Panel

Installing/Removing the Switch Blocks

(1) Preparing the Panel (3) Mounting the Switch on the Operation Unit

(2) Mounting the Operation Unit on the Panel (4) Removing the Switch

(1) Installing the Switch Blocks (2) Removing the Switch Blocks Wiring

• The panel dimensions are shown below.

• Recommended panel thickness: 1 to 5 mm.

• A Lock Ring is provided as a standard feature.

•When painting or coating the panel, make sure that the specified panel

dimensions apply to the panel after painting or coating.

22.3 dia.

3.2 2-R0.8MAX.

+0.4

+0.2

+0.4

24.1

• Insert the Operation Unit into the Switch Unit, aligning the arrow mark

inscribed on the Case with the lever on the Switch Blocks, then move the

lever in the direction indicated by the arrow in the following figure.

Switch Unit

Lever

Arrow mark

Operation Unit

• Insert the Operation Unit from the front surface of the panel, insert the Lock

Ring and the mounting ring from the terminal side, then tighten the ring.

Before tightening, check that the rubber washer is present between the

Operation Unit and the panel.

• Tighten the mounting ring at a torque of 0.98 to 1.96 N·m.

•When using a Lock Ring, insert the projecting part into the lock slot, and

then tighten the mounting ring.

22 dia.

+0.4

24.1+0.4

Key Operation Unit Arrow mark Projecting part Mounting ring

Rubber washer Panel Lock Ring

• Move the lever in the direction indicated by the arrow in the following figure,

then pull the Operation Unit or the Switch Blocks. Since the lever has a hole

with an inside diameter of 6.5 mm, the lever can be moved in the specified

direction by inserting a screwdriver into the hole and then moving the screw-

driver.

OPEN

LOCK

Screwdriver

• Hook the small protrusion on the Mounting Latch

into the groove on the other side of the lever,

then push up the Switch Block in the direction

indicated by the arrow in the figure below.

Switch block

Mounting Latch

Lever

Protrusion

• Insert a screwdriver between the Mounting Latch

and the Switch Block, then push down the

screwdriver in the direction indicated by the

arrow in the following figure.

Use either of the following screwdrivers.

Flat-head screwdriver 3 to 6 mm

3 to 6 mm dia.

Phillips screwdriver

Screwdriver

• Loosen the terminal screw from the Switch

Unit until it completely comes off the groove,

insert a screwdriver as shown in the follow-

ing figure, then push up the washer in the

direction indicated by the arrow to tempo-

rarily secure it. Now, a round crimp terminal

can be connected. After inserting the termi-

nal, tighten the screws to complete wiring.

Screwdriver

Washer

Screw

A22TK

Application Examples

Note: The above PL is only the evaluation result of the example. The PL must be evaluated in an actual application by the customer after confirming

the usage conditions.

●Application Overview

1. When the emergency stop switch S1 is pressed.

•The power supply to the motor M1 and M2 is turned OFF immediately when the emergency stop switch S1 is pressed.

•The power supply to the motor M1 is kept OFF until the reset switch S2 is pressed while the emergency stop switch S1 is released.

•When normal operating mode (M1 = ON, M2 = OFF) is selected on the selector switch S8, the power supply to the motor M2 is kept OFF until the guard is closed

and the reset switch S2 and S7 are pressed while the emergency stop switch S1 is released.

•When maintenance mode (M1 = OFF, M2 = ON) is selected on the selector switch S8, the power supply to the motor M2 is kept OFF until the enabling switch is

gripped to the middle position and the reset switch S2 and S7 are pressed while the emergency stop switch S1 is released.

2. Normal operating mode (the emergency stop switch S1 is released)

•Normal operating mode (M1 = ON, M2 = OFF) is selected on the selector switch S8. The enabling switch S3 is disabled.

•Power is supplied to motor M2 when the guard is closed.

•After opening of the guard is permitted by turning ON of the lock release enable signal, the lock release switch S5 is pressed, then the guard lock is released and the

guard is opened. Opening of the guard is detected by S4 and S6, and the power supply to the motor M2 is turned OFF immediately (The power supply to the motor

M1 is kept ON).

•The power supply to the motor M2 is kept OFF until the guard is closed and the reset switch S7 is pressed.

3. Maintenance mode (the emergency stop switch S1 is released)

•Maintenance mode (M1 = OFF, M2 = ON) is selected on the selector switch S8 after the motor M2 is stopped. S4 and S6 for detecting the opening and closing of

the guard are disabled.

•After opening of the guard is permitted by turning ON of the lock release enable signal, the lock release switch S5 is pressed, then the guard lock is released and the

guard is opened.

•The power supply to the motor M2 is turned ON while the enabling switch is gripped to the middle position.

•If the enabling switch is released or gripped past the middle position, the power supply to the motor M2 is turned OFF immediately.

•The power supply to the motor M2 is kept OFF until the enabling switch is gripped again to the middle position and the reset switch S7 is pressed.

Highest achievable PL/

safety category Model Stop category Reset

PLe/4 equivalent

A22TK-@-11-@@ Safety Key Selector Switch

D4NL / D4SL-N / D4JL Guard Lock Safety-door Switch (Mechanical Lock Type)

D4N / D4F Safety Limit Switch

A4EG Enabling Grip Switch

G9SX-GS226-T15 Safety Guard Switching Unit

G9SX-BC202 Flexible Safety Unit

0 Manual

KM4

KM3

+24V

KM4

KM3

KM4KM3

PLC etc.

Open OpenOpenOpen

Feedback loop

S14

S24 S44 S54

X3X2X1 X4

T11

T12 T21

Y1 Y3

T22 T61 T62

M1 M2

T71

Y2 Y4

T72 T31 T32 T33 T41 T42

OFF

AND

Auto

Manual

G9SX-GS226-T15 (Unit 2)

Control circuit

+24V

S14

S24

L1 L2

X1 X2

T11

T12 T21 T22 T31 T32 T33

KM2

KM1

+24V

KM1 KM2

KM2

KM1

PLC etc.

+24V

Open

Feedback loop

Guard lock

Safety-door Switch

Condition monitoring of

Safety-door Switch

G9SX-BC202 (Unit 1)

Control circuit

Indicator

(Diagnostic check enabled)

Indicator

(Diagnostic check enabled)

Enabling

Switch

OPEN

Lock release enable signal

UA UB

+24V

Selector Switch

A22TK

Guard

Emergency Stop

Switch

(2)

(1)

(4)

(3)

S1: Emergency Stop Switch

S2, S7: Reset switches

S3: Enabling Switch

S4: Guard lock Safety-door Switch

S5: Lock release switch

S6: Safety Limit Switch

S8: A22TK Safety Key Selector

Switch

KM1 to KM4: Magnetic contactors

M1 to M2: Motor

A22TK

Reset switch S2

KM1, KM2

NO contact

Unit 1

Logical AND output L1

Emergency

Stop Switch S1

Unit 1 S14, S24

G9SX-BC202(Unit 1)

G9SX-GS226-T15(Unit 2)

(10)

(8)(3)

(6)(4)

(1) (7)(5) (9)

(2)

KM3, KM4

NO contact

Unit 2

Logical AND input T41

Lock release

switch

Guard Lock

Safety-door Switch

Mode selection input M2

(Selector Switch S8)

Mode selection input M1

(Selector Switch S8)

Reset switch S7

Enabling Switch S3

Unit 2 S14, S24

Timing Chart

(1) Start the unit 2 in normal operating mode.

(2) Switch to maintenance mode by operating the selector switch.

(3) After checking that the motor has stopped, press the lock release switch to release the guard lock, and open the door to perform maintenance.

(4) Grip the enabling switch to the middle position.

(5) Press the reset switch to start the unit 2 in maintenance mode.

(6) Release (or grip) the enabling switch to stop the unit 2.

(7) After closing the guard and switching to operating mode by operating the selector switch, press the reset switch to restart the unit 2.

(8) After checking that the motor has stopped after a stop signal is input during operating mode, press the lock release switch and open the guard to

stop the unit 2.

(9) Close the guard and press the reset switch to restart the unit 2.

(10)Operate the emergency stop switch -> All the units stop.

Note: The lock release enable

signal must be configured so

that it should turn ON after

dangerous movement is

stopped and safety is ensured

for the door to open.

A22TK

Safety Precautions

Be sure to read the precautions for All Pushbutton Switches in the website at:http://www.ia.omron.com/.

Indication and Meaning for Safe Use

Installation Environment

• Do not use the switch in locations where explosive or flammable

gasses may be present.

• Do not use the switch submerged in oil or water or in locations

continuously subject to splashes of oil or water. Doing so may

result in oil or water entering the switch.

Wiring

• Connect a fuse in series with the A22TK to protect it from

shortcircuit damage. The value of the breaking current of the fuse

must be calculated by multiplying the rated current by 150% to

200%.

When using the A22TK for an EN rating, use a 10-A fuse of type gI

or gG that complies with IEC 60269.

• Always make sure that the power is turned OFF before wiring the

Switch.

Also, do not touch the terminals or other current-carrying ports

while power is being supplied.

• Check the contact specifications before mounting the Switch

Block. Use an NC contact for a safety circuit. It may not operate

properly. Check the Switch Block for safe operation before use.

• Check the operating specification before mounting the Operation

Unit. It may not operate properly. Check the Operation Unit for safe

operation before use.

Installation

• Do not drop the Switch. Doing so may prevent the Switch from

functioning to its full capability.

• Make sure the Switch is mounted securely to prevent it from falling

off. Otherwise injury may result.

• Mount the Operation Key so that it will not come into contact with

persons in the area when the door is opened and closed. Injury

may result.

• Do not use a Switch as a stopper. Otherwise, the switch may be

damaged and may not operate properly.

• Be sure to use the supplied Lock Ring. Otherwise, the switch may

rotate and may not operate properly.

Others

• Do not attempt to disassemble or modify the Switch. Doing so may

cause the Switch to malfunction.

• The durability of the Switch is greatly influenced by the switching

conditions. Always test the switch under actual working conditions

before application and use it in a switching circuit for which there

are no problems with performance.

• The user must not maintain or repair equipment incorporating the

Switch. Contact the manufacturer of the equipment for any

maintenance or repairs required.

Operating Environment

• This Switch is designed for use indoors.

Using the Switch outdoors may damage it.

• Do not use the Switch where corrosive gases (e.g., H2S, SO2, NH3,

HNO3, or CI2) are present or in locations subject to high

temperature and humidity. Doing so may result in damage to the

Switch as a result of contact failure or corrosion.

• Do not use the Switch in any of the following locations.

• Locations subject to extreme temperature changes

• Locations subject to high humidity or condensation

• Locations subject to excessive vibration

• Locations where metal dust, processing waste, oil, or chemicals

may enter through the protective door

• Locations subject to detergents, thinners, or other solvents

Storage

• Do not store the Switch where corrosive gases (e.g., H2S, SO2,

NH3, HNO3, or Cl2) or dust is present, or in locations subject to high

temperature or high humidity.

Mounting

• Do not tighten the mounting ring more than necessary using tools

such as pointed-nose pliers. Doing so will damage the mounting

ring. The tightening torque is 0.98 to 1.96 N·m.

• Recommended panel thickness: 1 to 5 mm.

Indicates an imminently hazardous

situation which, if not avoided, is likely to

result in serious injury or may result in

death. Additionally there may be severe

property damage.

Indicates a potentially hazardous situation

which, if not avoided, may result in minor

or moderate injury or in property damage.

Precautions

for Safe Use

Supplementary comments on what to do

or avoid doing, to use the product safely.

Precautions

for Correct

Use

Supplementary comments on what to do

or avoid doing, to prevent failure to

operate, or undesirable effect on product

performance.

DANGER

Always confirm that safety functions are operational

before stating operation. Wiring mistakes, setting

mistakes, switch failure or other factors may prevent

safety functions from operating. This may result in the

machine continuing to operate, possibly resulting in

human accidents.

CAUTION

If the Operation Unit is separated from the Socket Unit,

the equipment will not stop, creating a hazardous

condition.

Secure the lever on the Socket Unit by using the A22Z-

3380 Lock Plate so that the Operation Unit cannot be

easily separated from the Socket Unit.

(Refer to “Mounting the Lock Plate” at the right.)

[Used in combination with a Slide Key]

The machine may operate, possibly causing injury.

Do not disable safety function by using a spare door

switch operation key or spare key with the door

open.

[Used outside/inside hazardous area]

The machine may operate, possibly causing injury.

Do not disable safety function by using a spare key

outside or inside the hazardous area.

Precautions for Safe Use

DANGER

CAUTION

Precautions for Correct Use

A22TK

Mounting the Lock Plate

1. Confirm that the lever on the Mounting Latch is on the side where

the Operation Unit is secured and then insert the protrusion on the

Lock Plate into the hole in the lever on the Mounting Latch.

2. Press the hole on the Lock Plate onto the protrusion on the Mount-

ing Latch until it clicks into place.

After mounting the Lock Plate, check that the lever does not move.

Operating the Key

•When rotating the key to the total travel position or free position,

the operating force must be 1.47 N·m max.

Wiring

• Terminal screws must be Phillips or slotted M3.5 screws with a

square washer.

• The tightening torque is 1.08 to 1.27 N·m.

• Single wires, stranded wires, and crimp terminals can be

connected to the Switch

• Applicable Wiring Materials:

Twisted strands: 2 mm2 max.

Solid wire: 1.6 mm dia. max.

• After wiring the Switch, maintain an appropriate clearance and

creepage distance.

• Do not pull the lead wires with excessive force. Doing so may

disconnect them.

• The cable cannot be bended repeatedly.

•When bending the cable, provide a bending radius of 45 mm min.

so as not to damage the cable insulation or sheath. Excessive

bending may cause fire or leakage current.

Operating Environment

• The IP65 model is designed with a protective structure so that it will

not sustain damage if it is subjected to water from any direction to

the front of the panel.

• The Switch is intended for indoor use only. Using the Switch

outdoor may cause it to fail.

Using the Microload

Contact failure may occur if a Switch designed for a standard load is

used to switch a microload. Use Switches within the application

ranges shown in the following graph. Even within the application

range, insert a contact protection circuit, if necessary, to prevent the

reduction of life expectancy due to extreme wear on the contacts

caused by loads where inrush current occurs when the contact is

opened and closed.

The minimum applicable load is the N-level reference value. This

value indicates the malfunction reference level for the reliability level

of 60% (λ 60) (conforming to JIS C5003).

The equation, λ 60 = 0.5 x 10-6/time indicates that the estimated

malfunction rate is less than 1/2,000,000 with a reliability level of 60%.

Others

• If the panel is to be coated, make sure that the panel meets the

specified dimensions after coating.

• Due to the structure of the Switch, severe shock or vibration may

cause malfunctions or damage to the Switch.

Also, most Switches are made from resin and will be damaged if

they come into contact with sharp objects. Particularly scratches

on the Operation Unit may create visual and operational

obtrusions.

Handle the Switches with care, and do not throw or drop them.

• Perform maintenance inspections periodically.

• Do not use the key switch to stop/start the machine.

• Mode switching by key must be performed by the operator

specified in the operating manual.

• Apply load current not to exceed the rated value.

• The contact ON/OFF timing is not synchronized. Confirm

performance before application.

LOCK

OPEN

Lever Lock Plate

Mounting Latch

Operation Unit

8 mm max.

16.0 mm max. 20.2 mm max.

8 mm dia. max. 8 mm max.

16.0 mm max. 20.2 mm max.

8 mm dia. max.

Naked Crimp Terminals Crimp Terminals with

Insulating Sheaths

Microload area Area of use

Standard

load area

Invalid area

0.1 1 10 100 1,000

10mA

1mA

0.16mA

Voltage (V)

1.6mA 100mA

Current (mA)

Do not place or drop

heavy objects

on the Switch.

Do not operate the Switch

with hard or sharp objects.

Screwdriver

Hammer

Do not allow the Switch

to drop and hit the floor.

MEMO

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have

any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing

by Omron). Omron disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE

PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL

SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products

or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,

to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the

non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price

of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other

claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,

installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by

Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or

unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system

assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in

writing, are not to be construed as an amendment or addition to the above warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is

not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,

or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with

respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it

to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice

to change part numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be

assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to

confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

Authorized Distributor:

In the interest of product improvement,

specifications are subject to change without notice.

Cat. No. A189-E1-02 0917 (0409)

OMRON Corporation Industrial Automation Company

OMRON ELECTRONICS LLC

2895 Greenspoint Parkway, Suite 200

Hoffman Estates, IL 60169 U.S.A.

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69, 2132 JD Hoofddorp

The Netherlands

Tel: (31)2356-81-300/Fax: (31)2356-81-388

Contact: www.ia.omron.com

Kyoto, JAPAN

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark,

Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

CSM_9_3_1018