MTG14C-Series - Yamatake Corporation

Specifications are subject to change without notice. - 1 - First issue: May. 2003 Rev.1: Mar. 2004

No. SS2-MTG200-0100 (Rev.1)

MagneW Two-wire PLUS

Smart Two-wire Electromagnetic Flowmeter

Model MTG18A (Integral type)

Model MTG14C/MTG18B (Remote type)

Integral type

Remote type

OVERVIEW

The MagneW Two-wire PLUS is a high perfor-

mance electromagnetic flowmeter based on field

proven Yamatake two-wire loop powered tech-

nology . The MagneW Two-wire PLUS offers the

stable and accurate measurement of a traditional

magflow meter with low power consumption.

The result is a lower overall cost of ownership.

FEATURES

Two-wire operation

MagneW Two-wire PLUS significantly reduces

installation costs when compared to a traditional

four wired magnetic flowmeter.

High accuracy and stable output

MagneW Two-wire PLUS provides high accu-

racy (± 0.5% of rate) and its output is as stable as

current four wired magnetic flowmeters.

Minimum measurable fluid conductivity

The MagneW Two-wire PLUS offers a mini-

mum process fluid conductivity of 10 µS/cm

which is the best among two-wire magflow

meters thereby maximizing applicability.

Wider range in size

MagneW Two-wire PLUS offers wider range in

detector size.

Detector size: 2.5 to 200 mm.

Wafer and flange style, integral and

remote style available

The MagneW Two-wire PLUS is available inte-

gral or remote. Flange or wafer, making the

selection of the right meter for the application

simple.

APPLICATION

(1) Corrosive liquid measurement

(2) Chemical solution measurement

(3) Drainage/waste disposal fluid measurement

(4) Drinking water and waste water service

(5) Industrial/agricultural water measurement

(6) Seawater measurement

The above flow measurements are applicable.

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 2 -

FUNCTIONAL SPECIFICATIONS

Enclosure rating

NEMA TYPE 4X, IEC IP67

Hazardous Areas certifications

The following is planned to make approval applications.

FM CL I,II,III, DIV 1, Groups A,B,C,D,E,F&G,T4

FM NI for CL I,II,III, DIV 2, GPs A,B,C,D,F&G, T4

Output signal

Analog output

4 to 20mA DC

Digital output

Analog or Digital output is selectable.

Pulse output

Open collector output (30V DC, 100 mA max.)

Pulse frequency: 0.0001 to 200 Hz

Pulse width: 1 ms to 1 s

Contact output

Open collector output (30V DC, 100 mA max.)

Pulse or contact output is selectable

Communication protocol

SFC communication and HART® communication

Load resistance characteristic of communi-

cation

External power supply 21.05 to 42V DC for com-

munication.

Note) The load resistance of 250

Ω

or more is

necessary for communications of SFC and

the HART® communicator.

Flow unit

Volume flow: m3, L, cm3, G (gallon), mG, kG,

B (barrel), IG (imperial gallon), mIG,

kIG

Mass flow: t, kg, g, lb

Time: d, h, m, s

Display

Display: LCD

Main display: 7-segment, 8 di gits

Sub display: 16 digi ts, 2 lines

Display contents:

Demonstrates three values simultaneously

% flow rate, Actual flow rate, Totalized value

Data setting

Operation by four key switches

Damping

Adjustable between 0.5 and 199.9 seconds.

Low flow cutoff

Adjustable between 0 and 10% of setting range.

Below selected value, output is driven to the zero

flow rate signal level.

Dropout

Adjustable between 0 and 10% of setting range.

Below selected value, pulse output is cut.

Lightning protection

12 kV, 1000A

Equipped with the lightning arrester in the power

source and external output terminals.

Power failure

An EEPROM retains data record of totalized value

when pulse output is used (retention period approxi-

mately 10 years).

Power supply

15.6 to 42V DC (without communication)

21.05 to 42V DC (with communication)

Size

Wafer style

25, 40, 50, 65, 80, 100 mm (1, 1½, 2, 2½, 3, 4 inches)

Flange style

2.5, 5 mm (0.1, 0.2 inch) (Model MTG18A only)

10, 15, 25, 40, 50, 65, 80, 100, 150, 200 mm (3/8,

1/2, 1, 1½, 2, 2½, 3, 4, 6, 8 inches)

Flange rati ng

ANSI150, ANSI300, DIN PN10, DIN PN16, DIN

PN25, JIS10K, JIS20K, JIS30K

Ambient temperature limits

-20 to 60°C (-4 to 140°F)

Ambient humidity limits

10 to 90% RH

Load resistance (Ω)

Power supply (V DC )

0.0218

V-15.6

21.05<V<301

R= 0.02383

V-14.25

30<V<422

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 3 -

Temperature range and pressure range of process fluid

Refer to the following.

Measurable electrical conductivity

10 µS/cm or greater

50 µS/cm or greater (10 mm (3/8 inch), 15 mm (1/2 inch) for remote type)

Measurement flow range

Velocity V (m/s) = K × QK = Conversion factor = 1/3600 × 4/(

D2) × 10002

D = Size (mm)

Q = Flow rate (m3/h)

PERFORMANCE SPECIFICATIONS

Analog output accuracy

<Size: 2.5, 5 mm (0.1, 0.2 inch)> Vs = velocity of setting range (m/s)

<Size: 10, 15 mm (3/8, 1/2 inch)> Vs = velocity of setting range (m/s)

<Size: 25 to 200 mm (1 to 8 inches)> Vs = velocity of setting range (m/s)

Size: 2.5 to 10 mm (0.1 to 3/8 inch) Size: 15 to 200 mm (1/2 to 8 inches)

Size Maximum flow velocity range is

0 to 0.3 m/s (0 to 0.98 ft/s) Maximum flow velocity range is

0 to 10 m/s (0 to 32.8 ft/s) Conversion

factor K

Minimum range Maximum range

mm inches m3/h GPM m3/h GPM

2.5 0.1 0 to 0.00531 0 to 0.02335 0 to 0.1767 0 to 0.778 56.59

5 0.2 0 to 0.02121 0 to 0.09337 0 to 0.7068 0 to 3.112 14.15

10 3/8 0 to 0.08483 0 to 0.3735 0 to 2.827 0 to 12.44 3.537

15 1/2 0 to 0.1909 0 to 0.8404 0 to 6.361 0 to 28.01 1.572

25 1 0 to 0.5302 0 to 2.335 0 to 17.67 0 to 77.80 0.5659

40 1½ 0 to 1.358 0 to 5.976 0 to 45.23 0 to 199.1 0.2210

50 2 0 to 2.121 0 to 9.337 0 to 70.68 0 to 311.2 0.1415

65 2½ 0 to 3.584 0 to 15.78 0 to 119.4 0 to 525.9 0.08371

80 3 0 to 5.429 0 to 23.90 0 to 180.9 0 to 796.7 0.05526

100 4 0 to 8.483 0 to 37.35 0 to 282.7 0 to 1244 0.03537

150 6 0 to 19.09 0 to 84.04 0 to 636.1 0 to 2801 0.01572

200 8 0 to 33.93 0 to 149.4 0 to 1130 0 to 4979 0.008842

Vs (m/s) Velocity during measurement > Vs×50% Velocity during measurement < Vs×50%

±0.5% of rate ±0.5% of Vs

±% of rate ±%

Vs (m/s) Velocity during measurement > Vs×40% Velocity during measurement < Vs×40%

±0.5% of rate ±0.5% of Vs

±% of rate ±%

Vs (m/s) Velocity during measurement > Vs×30% Velocity during measurement < Vs×30%

±0.5% of rate ±0.5% of Vs

±% of rate ±%

2.94 MPa

(426 psi)

1.96 MPa

(284 psi)

-0.098 MPa

(-14.2 psi)

-20 C

(-4 F)

80 C

(176 F)

100 C

(212 F)

2.94 MPa

(426 psi)

-0.098 MPa

(-14.2 psi)

0.98 MPa

(142 psi)

-20 C

(-4 F)

80 C

(176 F)

120 C

(248 F)

130 C

(266 F)

1.0 Vs 10≤≤

0.3 Vs 1.0≤≤ 0.5

------- 0.5 0.5

-------





1.0 Vs 10≤≤

0.3 Vs 1.0≤≤ 0.5

------- 0.4 0.5

-------





1.0 Vs 10≤≤

0.3 Vs 1.0≤≤ 0.5

------- 0.3 0.5

-------





No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 4 -

PHYSICAL SPECIFICATIONS

Converter case finishing

Standard

Baked acryl pa int

Corrosion-proof

Baked epoxy paint

Converter case material

Aluminum alloy

Display cover material

Tempered glass

Terminal box finishing (Model MTG18B only)

Standard

Baked acryl pa int

Corrosion-proof

Baked epoxy paint

Terminal box material (Model MTG18B only)

Aluminum alloy

Detector main body materials

Case material

Size 2.5 to 15 mm (0.1 to 1/2 inch):

SCS13 stainless steel

Size 25 to 200 mm (1 to 8 inches):

SUS304 stainless steel

Measuring pipe material

SUS304 stainless steel

Flange

SUS304 stainless steel (size 2.5 to 65 mm (0.1 to

2½ inches))

Carbon steel + corrosion-preventive painting (size

80 to 200 mm (3 to 8 inches))

Process wetted materials

Lining

PFA

Electrode

SUS316L, Hastelloy C, Titanium, Tantalum,

Nickel, Zirconium, Platinum-Iridium

Grounding ring

SUS316, Hastelloy C, Titanium, Tantalum, Zirco-

nium, Platinum

INSTALLATION

Electrical connection

1/2NPT internal thread (must be selected for FM

approval)

CM20 internal thread

G1/2 internal thread

Remote converter mounting

Wall mounting, 2-inch pipe mounting

Grounding

Grounding resistance should be less than 100 Ω.

Pipe connection

Wafer style (Size: 25 to 100 m m (1 to 4 inches))

Flange style (Size: 2.5 to 200 mm (0.1 to 8 inches))

Length of straight pipe

Required straight pipe length clearance on the

upstream side and the downstream side, while install-

ing the detector.

Upstream side

A minimum 5D straight pipe length is required.

A minimum 10D straight pipe length is required if a

diffuser/valve/pump is installed upstream side.

Downstream side

2D straight pipe length is recommended.

(Where D is the nominal bore diameter of the

detector)

Cable between converter and detector

(Remote type)

Length

70 m (233 ft) or under

(25 mm (1 inch) to 200 mm (8 inches))

30 m (98 ft) or under

(10 mm (3/8 inch), 15 mm (1/2 inch))

Outside diameter

11.4 mm (0.45 inch)

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 5 -

MODEL SELECTION

MagneW Two-wire PLUS

Model MTG18A - I II III IV V VI VII VIII IX X XI - XII XIII - Options (some options can be selected per each model)

Basic model no. Selections Optional selectionsOptions

MTG18A --

I Line size 2.5 mm (0.1 inch) (flange type only) 002 *1 X None

Options

5 mm (0.2 inch) (flange type only) 005 *1 A Test report

10 mm (3/8 inch) (flange type only) 010 *1 B Traceability cer ti fi cat e

15 mm (0.5 inch) (flange type only) 015 *1 C Material certificate (elec-

trode/grounding ring)

25 mm (1 inch) 025

40 mm (1½ inches) 040 G Gasket for plastic piping

50 mm (2 inches) 050 J Tropical treatment

65 mm (2½ inches) 065 K with tagging on the converter

housing *3

80 mm (3 inches) 080

100 mm (4 inches) 100 L with tag number plate wired

to the flowmeter

150 mm (6 inches) (flange type only) 150

200 mm (8 inches) (flange type only) 200

II Lining PFA P X Finish /

paint XII

III Pipe connec-

tion Wafer JIS10K 11 2 Corrosion-proof finish

Wafer JIS16/20K 12

Wafer JIS30K 13 X Bolt and

nut None XIII

Wafer ANSI 150 21 2 SUS304 (only for wafer type)

Wafer ANSI 300 22

Wafer DIN PN10 41

Wafer DIN PN16 42

Wafer DIN PN25 43

Wafer DIN PN40 44

Flange JIS10K J1

Flange JIS20K J2

Flange JIS30K J3

Flange JIS10K for 10 mm size flange *2 J4

Flange JIS20K for 10 mm size flange *2 J5

Flange ANSI 150 A1

Flange ANSI 300 A2

Flange DIN PN10 D1

Flange DIN PN16 D2

Flange DIN PN25 D3

Flange DIN PN40 D4

IV Electrode SUS316L L

Hastelloy C C

Titanium K

Zirconium H

Tantalum T

Nickel N

Platinum-iridium P

V Grounding

ring SUS316 S

Hastelloy C C

Titanium K

Zirconium H

Tantalum T

Note) *1: Flange of size 2.5 to 15 mm detector

is 15 mm flange.

*2: Available for size 2.5 to 10 mm detec-

tor.

*3: Must be selected if tagging is

required.

Platinum P

Nickel N

VI Wiring con-

nection G1/2 internal thread A

G1/2 internal thread with plastic water tight gland B

G1/2 internal thread with brass Ni-plated watertight gland C

1/2NPT internal thread (must be selected for FM approval) D

CM20 internal thread E

G1/2 internal thread with two plastic watertight glands J

G1/2 internal thread with two brass Ni-plated watertight gland

VII Face to face

dimension Standard A

Replacement for SMT3000 (for wafer type 40 to 100 mm) S

VIII Installation /

Display

direction

Horizontal piping / Right side viewed from upstream A

Horizontal piping / Left side viewed from upstream B

Horizontal piping / Downstream side C

Horizontal piping / Upstream side D

Vertical piping / Right side of piping / Flow direction: Upward E

Vertical piping mounting / Left side of piping / Flow direction: Upward F

IX Calibration Standard A

X Output /

communica-

tion

Volume flow 4-20mA DC output/with SFC communication A

Volume flow DE output/with communication C

Volume flow 4-20mA DC output with HART communication H

XI Approval None X

FM approval, CL I, II, III, DIV.1, GPs A, B, C, D, E, F & G, T4 1

FM approval, CL I, II, III, DIV.2, GPs A, B, C, D, F & G, T4 2

Direction

of flow

Direction

of flow

Direction

of flow Direction

of flow

Direction

of flow

Direction

of flow

Display direction code "A" Display direction code "B"

Display direction code "C" Display direction code "D"

Display direction code "E" Display direction code "F"

Display

Display Display

Display

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 6 -

MagneW Two-wire PLUS Wafer/Flange remote type converter

Model MTG14C - I II III IV - Options (some op tions can be selected per each model)

Basic model no. Selections

MagneW Two-wire PLUS Wafer/Flange remote type cable

Model SMC11 - I II III

Basic model no. Selections

MTG14C

I Analog output / communication Volume flow 4-20 mA DC output / with SFC communication A

Volume flow DE output / with communication C

Volume flow 4-20 mA DC output / with HART communication H

II Wiring connection G1/2 internal thread A

G1/2 internal thread with a plastic water-tight gland B

G1/2 internal thread with a brass Ni-plated water-tight gland C

1/2NPT internal thread D

CM20 internal thread E

III Converter mounting Wall mounting with standard bracket G

2-inch pipe mounting with standard bracket H

IV Approval None X -

V Option None X

Traceability ce rtificate B

With the Tag number plate on the converter housing K

Corrosion-proof paint 2

SMC11

I Cable 2 m (6 feet 8 inches) 02

3 m (10 feet) 03

4 m (13 feet 4 inches) 04

5 m (16 feet 8 inches) 05

10 m (33 feet 4 inches) 10

15 m (50 feet) 15

20 m (66 feet 8 inches) 20

30 m (100 feet) 30

40 m (133 feet 4 inches) 40

50 m (166 feet 8 inches) 50

60 m (200 feet) 60

70 m (233 feet 4 inches) 70

II Terminals for detector With terminals A

III Terminals for converter With terminals A

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 7 -

MagneW Two-wire PLUS Wafer/Flange remote type detector

Model MTG18B - I II III IV V VI VII VIII IX - Options (some options can be selected per each model)

Basic model no. Selections Options

MTG18B

I Diameter 10 mm (3/8 inch) 010 XNone

Options

15 mm (1/2 inch) 015 A Test report

25 mm (1 inch) 025 B T raceability certificate

40 mm (1½ inches) 040 C Material certificate (electrode/ ground-

ing ring)

50 mm (2 inches) 050

65 mm (2½ inches) 065 G Gasket for plastic piping

80 mm (3 inches) 080 K With the Tag number plate on the termi-

nal box

100 mm (4 inches) 100

150 mm (6 inches) 150 2 Corrosion-proof paint

200 mm (8 inches) 200 4 Attached stainless steel 304 bolts and

nuts for installation *1

II Lining PFA P

III Pipe con-

nection Wafer JIS10K 11 *1: Available for wafer type.

Wafer JIS16/20K 12

Wafer JIS30K 13

Wafer JIS 3451 F12 (Size: 80 mm or larger) 51

Wafer ANSI 150 21

Wafer ANSI 300 22

Wafer JPI 150 61

Wafer JPI 300 62

Wafer DIN PN10 41

Wafer DIN PN16 42

Wafer DIN PN25 43

Flange JIS10K J1

Flange JIS20K J2

Flange JIS30K J3

Flange JIS10K for 10 mm size flange J4

Flange JIS20K for 10 mm size flange J5

Flange JIS3451 F12 (Size: 80 mm or larger) G1

Flange ANSI 150 A1

Flange ANSI 300 A2

Flange JPI 150 P1

Flange JPI 300 P2

Flange DIN PN10 D1

Flange DIN PN16 D2

Flange DIN PN25 D3

IV Electrode SUS316L L

Hastelloy C C

Titanium K

Zirconium H

Tantalum T

Nickel N

Platinum-iridium P

V Grounding

ring SUS316 S

Hastelloy C C

Titanium K

Zirconium H

Tantalum T

Platinum P

VI Wiring con-

nection G1/2 internal thread A

G1/2 internal thread with plastic water-tight gland B

G1/2 internal thread with brass Ni-plated water-tight gland C

1/2NPT internal thread D

CM20 internal thread E

VII Face to face

dimension Standard A

Yamatake SMT3000 wafer type S

VIII

Calibration Standard calibration A

IX Approval None X

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 8 -

DIMENSIONS

All dimensions are in millimeters, dimensions in brackets ( ) are in inches (inch).

Model MTG18A - Flange type size 2.5 mm (0.1 inch) to 15 mm (1/2 inch)

- Flange type size 25 mm (1 inch)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included to

the face-to-face dimension.

Table 1

Size mm

(inch)

Model no. J1 J2 J3 J4 J5 A1 A2 D1/D2 D3/D4

Flange rating JIS ANSI DIN

10K 20K 30K 10K

10 mm flange 20K

10 mm flange 150 300 PN 10/16 PN 25/40

2.5 to 10

(0.1 to3/8) Dimension L 160 160 160 160 160 1 60 (6.3) 160 (6.3) 160 160

Weight (kg) 6.8 7 8 6.7 6.8 6.4 (14.1 lb) 6.9 (15.2 lb) 6.9 7.1

(1/2) Dimension L 200 200 200 20 0 200 200 (7.87) 200 (7.87) 200 200

Weight (kg) 7 7.2 8.2 6.9 7 6.6 (14.6 lb) 7.1 (15.7 lb) 7.1 7.3

(1) Dimension H267 267 269 - - 258 (10.16) 266 (10.47) 262 262

H1 63 63 65 - - 54 (2.13) 62 (2.44) 58 58

Weight (kg) 9.2 9.5 10.3 - - 8.4 (18.5 lb) 9.5 (20.9 lb) 9.1 9.4

( )

Case

M4 Grounding

terminal

Electrode

Flange

Name plate

( 0.35 ( 2)) Refer to Note 1

Grounding ring

(5.33)

(3.37)

(1.97)

(1.85)

(0.98)

(2.76)

(3.54)

(4.33)

(0.08)

(10.63)

(2.83)

(5)

(2.80)

( 4.41)

(5.35) Flange type

Size 2.5 mm to 15 mm

(0.1 inch to 1/2 inch)

Flange type

Size 25 mm

(1 inch )

Symbol Description

Flow rate

signal

Grounding

Pulse output or

contact output

(selectable)

Terminal

Case

M4 Grounding

terminal

Electrode

Flange

Name plate

Refer to Note 1

Grounding

ring

(7.87)

(5.35)

(0.98)

(2.76)

(5.33)

(3.37)

(1.85)

(1.97)

( 4.41)

(5)

(3.03)

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 9 -

Model MTG18A - Flange type size 40 mm (1½ inch) to 100 mm (4 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316 , a 3 mm of Teflon gasket dimen sion is included

to the face-to-face dimension.

Table 2

Size mm

(inches)

Model no. J1 J2 J3 A1 A2 D1/D2 D3/D4

Flange rating JIS ANSI DIN

10K 20K 30K 150 300 PN 10/16 PN 25/4 0

(1.5) Dimension H296 296 307 288 (11.34) 305 (12.01) 302 302

H1 85 85 96 77 (3.03) 94 (3.7) 91 91

H2 84 84 84 84 (3.31) 84 (3.31) 84 84

Weight (kg) 8.3 8.6 11 7.8 (17.2 lb) 10.1 (22.3 lb) 8.7 9.7

(2) Dimension H310 310 316 308 (1 2.13) 316 (12.44) 316 316

H1 90 90 96 88 (3.46) 96 (3.78) 96 96

H2 93 93 93 93 (3.66) 93 (3.66) 93 93

Weight (kg) 11.9 12 13.7 12.3 (2 7.1 lb) 13.8 (30.4 lb) 13.3 13.8

(2.5) Dimension H329 329 343 330 (1 2.99) 388 (13.31) 334 334

H1 102 102 116 103 (4.06) 111 (4.37) 107 107

H2 100 100 100 100 (3.94) 100 (3.94) 100 100

Weight (kg) 13.9 14 15.7 14 .3 (31.5 lb) 15.8 (34 . 8 lb) 15.3 15.8

(3) Dimension H345 354 359 346 (1 3.62) 359 (14.13) 354 354

H1 110 119 124 113 (4.45) 124 (4.88) 119 119

H2 108 108 108 108 (4.25) 108 (4.25) 108 108

Weight (kg) 14.4 16.7 20.4 17.3 (38.1 lb) 21.3 (47.0 lb) 14.4 16.5

100

(4) Dimension H367.5 376.5 384.5 378.5 (14.90 ) 392.5 (15.45) 373.5 381.5

H1 120 129 137 131 (5.16) 145 (5.71) 126 134

H2 120.5 1 20.5 120.5 120.5 (4.74) 120.5 (4.74) 1 20.5 120.5

Weight (kg) 20.2 23.7 28.6 25.1 (55.3 lb) 34.2 (75.4 lb) 19.6 23.4

Case

M4 Grounding

terminal

Electrode

Flange

Name plate

Refer to Note 1

Grounding

ring

(5.33)

(5)

(3.37)

(1.85)

(1.97)

(0.98)(2.76)

( 4.41)

(5.35)

(7.87)

Symbol Description

Flow rate

signal

Grounding

Pulse output or

contact output

(selectable)

Terminal

Flange type

Size 40 mm to 100 mm

(11/2 inch to 4 inches)

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 10 -

Model MTG18A - Flange type size 150 mm (6 inches) and 200 mm (8 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included

to the face-to-face dimension.

Table 3

Size mm

(inches)

Model no. J1J2J3 A1 A2 D1/D2D3 D4

Flange rating JIS ANSI DIN

10K 20K 30K 150 300 PN 10/16 PN 25 PN40

150

(6)

Dimension L 300 300 300 300 (11.81) 300 (11.81) 300 300 300

H462 476 487 461 (18.15) 483 (19.02) 465 473 473

H1 175 189 200 174 (6.85) 196 (7.72) 178 186 186

H2 160 160 160 160 (6.3) 160 (6.3 ) 160 160 160

Weight (kg) 34.4 41.7 54.3 37.2 (82.0 lb) 56.2 (123.9 lb) 30.7 38.6 38.6

200

(8)

Dimension L 350 350 350 350 (13.78) 350 (13.78) 350 350 350

H508 515 531 516 (20.31) 537 (21.14) 514 526 534

H1 196 203 219 204 (8.03) 225 (8.86) 202 214 222

H2 185 185 185 185 (7.28) 185 (7.28) 185 185 185

Weight (kg) 49.8 59.8 87 61.8 (136.2 lb) 90.8 (200.2 lb) 48.1 68.5 72

Flange type

Size 150 mm and 200 mm

(6 inches and 8 inches)

Symbol Description

Flow rate

signal

Grounding

Pulse output or

contact output

(selectable)

Terminal

Case

M4 Grounding

terminal

Electrode

Flange

Refer to Note 1

Grounding

ring

(5.33)

(3.37)

(1.85)

(1.97)

(0.98)

(2.76)

( 4.41)

(5)

(5.35)

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 11 -

Model MTG18A - Wafer type size 25 mm (1 inch) to 100 mm (4 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316 , a 3 mm of Teflon gasket dimen sion is included

to the face-to-face dimension.

Table 4

Flange rating 25 mm

(1 inch) 40 mm

(1½ inch) 50 mm

(2 inches) 65 mm

(2½

inches)

80 mm

(3 inches) 100 mm

(4 inches)

Face-to-face

dimension code AASAS A ASAS

Dimension

size

L94 (3.7)

80 (3.15) 98 (3.86) 86 (3.39)

104 (4.09)

96 (3.78)

106 (4.17) 130 (5.12) 120 (4.72) 150 (5.91)

H238 (9.37) 254.5 (10.02) 272 (10.71) 289 (11.38) 302 (11.89) 327 (12.87)

H1 34 (1.34) 43.5 (1.71) 52 (2.05) 62 (2.44) 67 (2.64) 79.5 (3.13)

H2 77 (3.03) 84 (3.31) 93 (3.66) 100 (3.94) 108 (4.25) 120.5 (4.74)

D68 (2.68) 87 (3.43) 104 (4.09) 124 (4.88) 134 (5.28) 159 (6.26)

Weight (kg) 3.7

(8.2 lb) 3.8

(8.4 lb) 4.3

(9.5 lb) 4.4

(9.7 lb) 5.0

(11.0 lb) 5.5

(12.1 lb) 6.4

(14.1 lb ) 7.1

(15.7 lb ) 8.2

(18.1 lb ) 9.2

(20.3 lb)

Wafer type

Size 25 mm and 100 mm

(1 inch and 4 inches)

Symbol Description

Flow rate

signal

Grounding

Pulse output or

contact output

(selectable)

Terminal

Name plate

M4 grounding

terminal

Case

Electrode L

Refer to note1

Grounding

ring

(5.33)

(3.37)

(1.97)

(1.85)

(0.98)

(2.76)

( 4.41)

(5)

(H1) H2

(5.35)

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 12 -

Model MTG14C - Converter

Wall mounting dimension

Wall mounting

Plate

Terminal

Symbol Description

I-OUT

PULSE/

STATUS

OUT

Flow rate signal

Grounding

Pulse output

or contact

(selectable)

Excitation output

Flow rate

signal input

2-inch pipe mounting

* Terminal screw: M4

(R0.16)

(0.75)

(R0.49)

(R0.31)

(10.67 )

+0.04

(R0.49)

(2.91+0.02)

(0.77)

(4.41)

(10.12)(10.12)

(0.63)

(1.19 max.)(1.19 max.)

(4.36)

(2.74)

(4.36)

(2.74)

(9.92)

(1.77) (1.77)

(4.92)

(1.77) (1.77)

(3.63)

(0.13)

(1.23)

(6.30)

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 13 -

Model MTG18B - Detector - Flange type size 10 mm (3/8 inch) and 15 mm (1/2 inch)

- Flange type size 25 mm (1 inch)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316 , a 3 mm of Teflon gasket dimen sion is included

to the face-to-face dimension.

Table 5

Size mm

(inches)

Model no. J1J2J3 J4 J5 A1 A2 D1/D2D3/D4

Flange rating JIS ANSI DIN

10K 20K 30K 10K

10 mm flange 20K

10 mm flange 150 300 PN 10/16 PN 25/40

(3/8) Dimension L 160 160 160 160 160 160 (6.3) 160 (6.3) 160 160

Weight (kg) 5 5.2 6.2 4.9 5 4.6 (10.1 lb) 5.1 (11.2 lb) 5.1 5.3

(1/2) Dimension L 200 200 200 2 00 200 200 (7.87) 200 (7.87) 200 200

Weight (kg) 5.2 5.4 6.4 5.1 5.2 4.8 (10.6 lb) 5.3 (11.7 lb) 5.3 5.5

(1) Dimension H187 187 189 - - 188 (7.4) 186 (7.32) 182 182

H1 63 63 65 - - 54 (2.13) 62 (2.44) 58 58

Weight (kg) 7.4 7.7 8.5 - - 6.6 (14.6 lb) 7.7 (17.0 lb) 7.3 7.6

9 ( 2)

0.35 ( 2)

()

Waterproof gland

Terminal box

Tag plate

Nameplate

Grounding ring

Electrode

(3.31)

(0.98)

(3.31)

(1.19 max.)

(7.48)

(1.85)

(2.80)(2.83)

(0.08)

(2.05)

(4.43)

(3.54)

(3.31)

(optional)

Waterproof gland

(optional)

Symbol Description

Excitation input

Flow rate signal

output

Grounding

* Terminal screw: M4

Terminal

Flange type

Size 10 mm and 15 mm

(3/8 and 1/2 inch)

Flange type

Size 25 mm (1 inch)

(1.85)

(3.03)

Terminal box

Tag plate

Nameplate

Grounding ring

(1.19 max.)

(3.31)

(0.98)

Blind plug

(7.89)

Electrode

Refer to note 1

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 14 -

Model MTG18B - Detector - Flange type size 40 mm (1½ inch) to 100 mm (4 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included

to the face-to-face dimension.

Table 6

Size mm

(inches)

Model no. J1J2J3 A1 A2 D1/D2D3/D4

Flange rating JIS ANSI DIN

10K 20K 30K 150 300 PN 10/16 PN 25/40

(1.5) Dimension H216 216 227 208 (8.19) 225 (8.86) 222 222

H1 85 85 96 77 (3.03) 94 (3.7) 91 91

H2 84 84 84 84 (3.31) 84 (3.31) 84 84

Weight (kg) 6.5 6.8 9.2 6 (13.2 lb) 8.3 (18.3 lb) 6.9 7.9

(2) Dimension H230 230 236 228 (8.98) 236 (9.29) 236 2 36

H1 90 90 96 88 (3.46) 96 (3.78) 96 96

H2 93 93 93 93 (3.66) 93 (3.66) 93 93

Weight (kg) 10.1 10.2 11.9 10.5 (23.1 lb) 12 (26.5 lb) 11.5 12

(2.5) Dimension H249 2 49 263 250 (9.84) 258 (10.16) 254 254

H1 102 102 116 103 (4.06) 111 (4.37) 107 107

H2 100 100 100 100 (3.94) 100 (3.94) 100 1 00

Weight (kg) 12.1 12.2 13.9 12.5 (27.6 lb) 14 (30.9 lb) 13.5 14

(3) Dimension H265 274 279 266 (10.47) 279 (10.98) 274 274

H1 110 119 124 113 (4.45) 124 (4.88) 119 1 19

H2 108 108 108 108 (4.25) 108 (4.25) 108 1 08

Weight (kg) 16.6 14.9 18.6 15.5 (34.2 lb) 19.5 (43.0 lb) 12.6 14.7

100

(4) Dimension H287.5 296.5 304.5 298.5 (11.75) 312.5 (12.30) 293.5 301.5

H1 120 129 137 131 (5.16) 145 (5.71) 126 1 34

H2 120.5 120.5 120.5 120.5 (4.74) 120.5 (4.74) 120.5 12 0.5

Weight (kg) 18.4 21.9 26.8 23.3 (51.4 lb) 32.4 (71.4 lb) 17.8 21.6

Case

Electrode

Flange

Refer to Note 1

Grounding

ring

(7.87)

(1.19 max.) (3.31)

(3.31)

Nameplate

Tag plate

Terminal box

Waterproof gland

(optional)

(1.85)

Symbol Description

Excitation input

Flow rate signal

output

Grounding

* Terminal screw: M4

Terminal

Flange type

Size 40 mm to 100 mm

(11/2 inch to 4 inches)

(0.98)

Blind plug

Yamatake Corporation No. SS2-MTG200-0100 (Rev.1)

- 15 -

Model MTG18B - Detector - Flange type size 150 mm (6 inches) and 200 mm (8 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316 , a 3 mm of Teflon gasket dimen sion is included

to the face-to-face dimension.

Table 7

Size mm

(inches)

Model no. J1J2J3 A1 A2 D1/D2D3D4

Flange rating JIS ANSI DIN

10K 20K 30K 150 300 PN 10/16 PN 25 PN 40

150

(6) Dimension

L300 300 300 300 (11.81) 300 (11.81) 300 300 300

H382 396 40 7 381 (15) 403 (15.87) 385 393 393

H1 175 189 200 174 (6.85) 196 (7.72) 178 186 186

H2 160 160 160 160 (6.3) 160 (6.3) 160 160 160

Weight (kg) 32.6 39.9 52.5 35.4 (78 lb) 54.4 (119.9 lb) 28.9 36.8 36.8

200

(8) Dimension

L350 350 3 50 350 (13.7 8) 350 (13.78) 350 350 350

H428 435 4 51 436 (17.1 7) 457 (17.99) 434 446 454

H1 196 203 219 204 (8.03) 225 (8.86) 202 214 222

H2 185 185 185 185 (7.28) 185(7.28) 185 185 185

Weight (kg) 48 58 85.2 60 (132.3 lb) 89 (196.2 lb) 46.3 66.7 70.2

Case

Electrode

Flange

Refer to Note 1

Grounding

ring

Symbol Description

Excitation input

Flow rate signal

output

Grounding

* Terminal screw: M4

Terminal

Flange type

Size 150 mm and 200 mm

(6 inches and 8 inches)

(1.19 max.) (3.31)

Nameplate

Tag plate

Terminal box

Waterproof gland

(optional)

(3.31)

(1.85)

(0.98)

Blind plug

No. SS2-MTG200-0100 (Rev.1) Yamatake Corporation

- 16 -

Model MTG18B - Detector - Wafer type size 25 mm (1 inch) to 100 mm (4 inches)

Note 1 • When grounding ring material is SUS316, gasket dimension is not included to the face-to-face dimension.

• When grounding ring material is other than SUS316, a 3 mm of Teflon gasket dimension is included

to the face-to-face dimension.

Table 8

Flange rating 25 mm

(1 inch) 40 mm

(1½ inch) 50 mm

(2 inches) 65 mm

(2½ inches) 80 mm

(3 inches) 100 mm

(4 inches)

Face-to-face

dimension code A ASAS A ASAS

Dimen-

sion size

L94 (3.7)

80 (3.15) 98 (3.86) 86 (3.39)

104 (4.09)

96 (3.78)

106 (4.17) 130 (5.12) 120 (4.72) 150 (5.91)

H158 (6.22) 174.5 (6.87) 192 (7.56) 209 (8.23) 222 (8.74) 2 47 (9.72)

H1 34 (1.34) 4 3.5 (1.71) 52 (2.05) 62 (2.44) 67 (2.64) 79.5 (3.13)

H2 77 (3.03) 84 (3.31) 93 (3.66) 100 (3.94) 108 (4.25) 120.5 (4.74)

D68 (2.68) 87 (3.43) 104 (4.09) 124 (4.88) 134 (5.28) 159 (6.26)

Weight (kg) 2

(4.4 lb) 2

(4.4 lb) 2.5

(5.5 lb) 2.6

(5.7 lb) 3.2

(7.1 lb) 3.7

(8.2 lb) 4.6

(10.1 lb ) 5.3

(11.7 lb) 6.4

(14.1 lb ) 7.4

(16.3 lb )

Symbol Description

Excitation input

Flow rate signal

output

Grounding

* Terminal screw: M4

Terminal

Wafer type

Size 25 mm to 100 mm

(1 inch to 4 inches)

Waterproof gland

(optional)

Terminal box

Tag plate

Nameplate

Grounding ring

Electrode

(1.19 max.)

(3.31)

(1.85)

Refer to Note 1

(0.98)

Case

Blind plug

2-12-19 S

hib

Shib

u, To

o 150-831

Tel

Fax

3486

2310

3486

2593

This has been printed on rec

cled paper

http://www.

amatake.com

avemation

Savin

rou

Automatio