05096 PSRDA3.3-4 thru PSRDA15-4 STEERING DIODE/ TVS ARRAY COMBO APPLICATIONS Ethernet - 10/100 Base T Computer I/O Ports - SCSI, FireWire & USB Set-Top Box Protection Video Card IEC COMPATIBILITY (EN61000-4) 61000-4-2 (ESD): Air - 15kV, Contact - 8kV 61000-4-4 (EFT): 40A - 5/50ns 61000-4-5 (Surge): 24A, 8/20s - Level 2(Line-Gnd) & Level 3(Line-Line) SO-8 FEATURES 500 Watts Peak Pulse Power per Line (tp=8/20s) Unidirectional Configuration Available in 4 Voltage Types: 3.3V to 15V Protects Up to Four (4) I/O Ports ESD Protection > 40 kilovolts Low Capacitance: 15pF RoHS Compliant MECHANICAL CHARACTERISTICS Molded JEDEC SO-8 Weight 70 milligrams (Approximate) Available in Lead-Free Pure-Tin Plating(Annealed) Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270C Consult Factory for Leaded Device Availability Flammability Rating UL 94V-0 12mm Tape and Reel Per EIA Standard 481 Marking: Marking Code, Logo, Date Code & Pin One Defined By Dot on Top of Package PIN CONFIGURATION 05096.R9 12/07 GND I/O 4 I/O 3 GND 8 7 6 5 1 2 3 I/O 1 +VREF +VREF 1 4 I/O 2 www.protekdevices.com PSRDA3.3-4 thru PSRDA15-4 DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25C Unless Otherwise Specified SYMBOL VALUE UNITS Peak Pulse Power (tp = 8/20s) - See Figure 1 PPP 500 Watts Operating Temperature TL -55 to 150 C Storage Temperature TSTG -55 to 150 C Maximum Forward Voltage @ 10mA (See Note 1) VF 1.1 Volts PARAMETER Note 1: Measured between pins 8 or 5 to 1, 2, 3, 4, 6 and 7. ELECTRICAL CHARACTERISTICS PER LINE PART NUMBER DEVICE MARKING PRA PRB PRD PRE PSRDA3.3-4 PSRDA05-4 PSRDA12-4 PSRDA15-4 @ 25C Unless Otherwise Specified RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) VWM VOLTS @ 1mA V(BR) VOLTS @ IP = 1A VC VOLTS 3.3 5.0 12.0 15.0 4.0 6.0 13.3 16.7 6.5 9.8 19.0 24.0 MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE (See Note 1) (See Figure 5) @8/20s VC @ IPP @VWM ID A @0V, 1 MHz Cj(SD) pF 10.9V @ 43.0A 13.5V @ 42.0A 25.9V @ 21.0A 30.0V @ 17.0A 125 20 1 1 15 15 15 15 Note 1: Capacitance measured at VWM = VCC connected between I/O pins to pin 8 and 5 (Gnd). VR = VWM @ 1MHz. As shown in Figure 5, REF1 is connected to ground, REF2 is connected to +VCC, and input applies to VCC = 5V, Vsign = mV, F = 1 MHz. 500W 8/20s Waveform 1,000 100 10 0.1 05096.R9 12/07 FIGURE 2 PULSE WAVE FORM 120 IPP - Peak Pulse Current - % of IPP PPP - Peak Pulse Power - Watts 10,000 FIGURE 1 PEAK PULSE POWER VS PULSE TIME tf 100 TEST WAVEFORM PARAMETERS tf = 8s td = 20s Peak Value IPP 80 e-t 60 40 td = t I /2 PP 20 0 1 10 100 td - Pulse Duration - s 1,000 10,000 2 0 5 10 15 t - Time - s 20 25 30 www.protekdevices.com PSRDA3.3-4 thru PSRDA15-4 GRAPHS FIGURE 3 POWER DERATING CURVE 100 40 Peak Pulse Power 8/20s 5 Volts per Division 80 % Of Rated Power FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR PSRDA05-4 60 40 30 20 10 20 0 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - C 150 FIGURE 5 INPUT CAPACITANCE CIRCUIT ESD Test Pulse: 8 kilovolt, 1/30ns (waveshape) FIGURE 6 TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR PSRDA05-4 12 I/O VR +VCC G VC - Clamping Voltage - Volts REF2 8 4 0 0 5 10 15 20 IPP - Peak Pulse Current - Amps REF1 FIGURE 7 INSERTION LOSS - PSRDA12-4 20 db 10 db per Division 10 db per Division 30 FIGURE 8 RETURN LOSS - PSRDA12-4 20 db Ref 0 db -20 db Ref 0 db -20 db -50 db -50 db 100 MHz per Division 100 MHz per Division 05096.R9 12/07 25 3 www.protekdevices.com PSRDA3.3-4 thru PSRDA15-4 APPLICATION NOTE The PSRDAxx-4 Series are low capacitance, unidirectional TVS arrays that are designed to protect I/O or high speed data lines from the damaging effects of ESD or EFT. This product series has a surge capability of 500 Watts PPP per line for an 8/20s waveshape and offers ESD protection > 40kV. DIFFERENTIAL-MODE CONFIGURATION (Figure 1) Figure 1. Typical Differential-Mode USB Protection Ideal for use in USB applications, the PSRDAxx-4 Series provides up to four (4) lines of protection in a differential-mode configuration as depicted in Figure 1. USB PORT VBUS D+ D- Circuit connectivity is as follows: Pins 1, 4, 6 and 7 are connected to the data lines. Pins 5 and 8 are connected to ground. Pins 2 and 3 are connected to the databus. VBUS GND 3 2 1 5 6 7 8 USB CONTROLLER 4 DIFFERENTIAL-MODE CONFIGURATION (Figure 2) The PSRDAxx-4 Series also provides up to four (4) lines of protection in a differential-mode configuration as depicted in Figure 2 for T1/E1 applications. Circuit connectivity is as follows: Pins 1, 4, 6 and 7 are connected to the data lines. Pins 5 and 8 are connected to ground. Pins 2 and 3 are connected to the databus. USB PORT GND GND VBUS D+ D- CIRCUIT BOARD LAYOUT RECOMMENDATIONS GND Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: Figure 2. Typical Differential-Mode T1/E1 Protection The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. PTC RTIP PLC016 The path length between the TVS device and the protected line should be minimized. RRING PTC All conductive loops including power and ground loops should be minimized. The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. T1/E1 TRANSCEIVER GND 4 3 2 1 5 6 7 8 GND PTC TTIP PLC016 TRING PTC 05096.R9 12/07 4 www.protekdevices.com PSRDA3.3-4 thru PSRDA15-4 SO-8 PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE SO-8 -A- 8 5 + 0.010 (0.25 MM) M B M 4 PL -B - P 1 G PACKAGE DIMENSIONS 4 DIM A B C D F G J K P R D C R x 45 0 - 10 -T- K 0.010 (0.25 MM) M T B S A S 8 PL + J F MILLIMETERS MIN MAX 4.80 3.80 1.35 0.35 0.40 1.27 BSC 0.18 0.10 5.80 0.25 INCHES MIN MAX 0.196 5.00 0.189 0.150 0.157 4.00 1.75 0.054 0.068 0.49 0.014 0.019 0.049 1.250 0.016 1.27 BSC 0.05 BSC 0.05 BSC 0.25 0.007 0.009 0.004 0.008 0.25 6.20 0.229 0.244 0.019 0.50 0.010 NOTES 1. 2. 3. 4. 5. 6. MOUNTING PAD 0.050 0.005 0.030 0.005 - T - = Seating Plane and Datum Surface. Dimensions "A" and "B" are Datum. Dimensions "A" and "B" do not include mold protrusion. Maximum mold protrusion is 0.015" (0.380 mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs. TAPE & REEL/BULK ORDERING NOMENCLATURE 0.160 0.005 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 1,000 pieces per 12mm tape, i.e. PSRDA05-4-T7. 3. Suffix-T13 = 13 Inch Reel - 2,500 pieces per 12mm tape, i.e., PSRDA05-4-T13. 4. Suffix - LF = Lead-Free, Pure-Tin Plating, i.e., PSRDA05-4-LF-T7. 5. No Suffix = Product Shipped in Tubes of 98 pcs per Tube. 0.245 MIN 0.045 0.005 Outline & Dimensions: Rev 1 - 11/01, 06009 COPYRIGHT (c) ProTek Devices 2007 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer's and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05096.R9 12/07 5 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com Web Site: www.protekdevices.com www.protekdevices.com