PRODUCT DATASHEET Strada-Module series last update 31/7/2013 Ordering number C11918_STRADA-T-6X1-DNW Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Strada-Module XP-E Clear 119.8 x 25.2 mm 5.6 mm Rectangular PMMA Screw, pin, glue Ready FWHM Efficiency cd/lm Gerber File Asymmetric degrees 93 % 0.410 Available FWHM Efficiency cd/lm Gerber File Asymmetric degrees 93 % 0.300 Available Ordering number C12449_STRADA-T-6X1-DWC Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Strada-Module XP-E Clear 119.8 x 25.2 mm 5.5 mm Rectangular PMMA Screw, pin, glue Ready NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. June 10th 2014 20:10 Copyright Ledil Oy - Subject to change without prior notice - Page 1/2 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001 PRODUCT DATASHEET Strada-Module series last update 31/7/2013 GENERAL INFORMATION - Product series especially designed & optimized for XP-E series of LEDs. - Special care taken to make light distribution as uniform as possible. - Lens material optical grade PMMA with high UV and temperature resistance (105 degrees of Celcius / 220 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used material from below: http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20UL94_Yellow%20Card.pdf http://ledil.fi/sites/default/files/Documents/Technical/Material/PMMA%208N%20PLEXIGLAS-Datasheet.pdf - Fastening to PCB with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. http://www.ledil.com/datasheets/DataSheet_GLUES.pdf NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of PCB surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer -this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the PCB. Further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. June 10th 2014 20:10 Copyright Ledil Oy - Subject to change without prior notice - Page 2/2 Ledil Oy Salorankatu 10 24240 SALO Finland http://www.ledil.com email: ledil@ledil.com FAX: +358-2-733 8001 Location pins 20 3.2 3.2 A B C D 20 4 4 LED in the center of the optic 20 1.19 1.98 2 x 3 3 . 5 Front view . 1.19 5.6 Beam direction 1.2 3 25.2 5 3 20 2 3. 1 3. Note, Ledil Oy won't provide tape or sealing plates for this product. 2x 20 Bottom view Tape option 3. 20 ( 59 ) 3. 2 119.8 Layout fully compatible with individual Stradaseries lenses 2 2 Tolerances for dimensions: 0-20mm tolerance value +-0.1mm 21-45mm tolerance value +-0.2mm 46-90mm tolerance value +-0.3mm 91-100mm tolerance value +-0.4mm 101-mm tolerance value +-0.5mm This drawing is our property. It can't be reproduced or communicated without our written agreement. 1 DRAWN BY pv DATE 120 Screw holes jl DATE 1.11.2012 DESIGNED BY hh DATE 02.12.2010 D Beam direction Ledil Oy Salorankatu 10 FIN-24100 SALO Finland DRAWING TITLE Datasheet Strada-T-6x1-DNW Lens 1.11.2012 CHECKED BY Typical layout Scale: 1:2 25.4 Materials: Lens PMMA SIZE DRAWING NUMBER C11918 A4 SCALE REV 2:1 WEIGHT(g) 6 SHEET A 1/1 1