Single Supply, Rail-to-Rail Low Power, FET-Input Op Amp AD824 FEATURES Single Supply Operation: 3 V to 30 V Very Low Input Bias Current: 2 pA Wide Input Voltage Range Rail-to-Rail Output Swing Low Supply Current: 500 A/Amp Wide Bandwidth: 2 MHz Slew Rate: 2 V/s No Phase Reversal APPLICATIONS Photo Diode Preamplifier Battery Powered Instrumentation Power Supply Control and Protection Medical Instrumentation Remote Sensors Low Voltage Strain Gage Amplifiers DAC Output Amplifier PIN CONFIGURATIONS 14-Lead Epoxy SOIC (R Suffix) 14 OUT D OUT A 1 13 -IN D -IN A 2 +IN A 3 AD824 12 +IN D +IN B 5 11 V- TOP VIEW (Not to Scale) 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C V+ 4 16-Lead Epoxy SOIC (R Suffix) 16 OUT D OUT A 1 -IN A 2 +IN A 3 V+ 4 +IN B 5 12 +IN C -IN B 6 11 -IN C OUT B 7 NC 8 15 -IN D 14 +IN D AD824 13 V- 10 OUT C 9 NC NC = NO CONNECT The AD824 is a quad, FET input, single supply amplifier, featuring rail-to-rail outputs. The combination of FET inputs and rail-to-rail outputs makes the AD824 useful in a wide variety of low voltage applications where low input current is a primary consideration. The FET input combined with laser trimming provides an input that has extremely low bias currents with guaranteed offsets below 1 mV. This enables high accuracy designs even with high source impedances. Precision is combined with low noise, making the AD824 ideal for use in battery powered medical equipment. The AD824 is guaranteed to operate from a 3 V single supply up to 15 V dual supplies. AD824AR-3V Parametric Performance at 3 V is fully guaranteed. Applications for the AD824 include portable medical equipment, photo diode preamplifiers and high impedance transducer amplifiers. Fabricated on ADI's complementary bipolar process, the AD824 has a unique input stage that allows the input voltage to safely extend beyond the negative supply and to the positive supply without any phase inversion or latchup. The output voltage swings to within 15 mV of the supplies. Capacitive loads to 350 pF can be handled without oscillation. The ability of the output to swing rail-to-rail enables designers to build multistage filters in single supply systems and maintain high signal-to-noise ratios. GENERAL DESCRIPTION The AD824 is specified over the extended industrial (-40C to +85C) temperature range and is available in narrow 14-lead and 16-lead SOIC packages. REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2003 Analog Devices, Inc. All rights reserved. AD824-SPECIFICATIONS ELECTRICAL SPECIFICATIONS (@ V = 5.0 V, V S Parameter Symbol INPUT CHARACTERISTICS Offset Voltage AD824A VOS CM = 0 V, VOUT = 0.2 V, TA = 25C unless otherwise noted) Conditions Min Typ Max Unit 0.1 1.0 1.5 12 4000 10 10133.3 mV mV pA pA pA pA V dB dB dB WpF TMIN to TMAX Input Bias Current 2 300 2 300 IB TMIN to TMAX Input Offset Current IOS TMIN to TMAX Input Voltage Range Common-Mode Rejection Ratio Input Impedance Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High CMRR AVO DVOS/DT VOH Output Voltage Low VOL Short Circuit Limit ISC Open-Loop Impedance ZOUT POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier PSRR ISY VCM = 0 V to 2 V VCM = 0 V to 3 V TMIN to TMAX -0.2 66 60 60 VO = 0.2 V to 4.0 V RL = 2 kW RL = 10 kW RL = 100 kW TMIN to TMAX, RL = 100 kW 20 50 250 180 40 100 1000 400 2 V/mV V/mV V/mV V/mV mV/C ISOURCE = 20 mA TMIN to TMAX ISOURCE = 2.5 mA TMIN to TMAX ISINK = 20 mA TMIN to TMAX ISINK = 2.5 mA TMIN to TMAX Sink/Source TMIN to TMAX f = 1 MHz, AV = 1 4.975 4.97 4.80 4.75 4.988 4.985 4.85 4.82 15 20 120 140 12 10 100 V V V V mV mV mV mV mA mA W VS = 2.7 V to 12 V TMIN to TMAX TMIN to TMAX 70 66 DYNAMIC PERFORMANCE Slew Rate Full-Power Bandwidth Settling Time Gain Bandwidth Product Phase Margin Channel Separation SR BWP tS GBP fo CS RL = 10 kW, AV = 1 1% Distortion, VO = 4 V p-p VOUT = 0.2 V to 4.5 V, to 0.01% NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density Total Harmonic Distortion en p-p en in THD 3.0 80 74 25 30 150 200 80 500 600 dB dB mA No Load f = 1 kHz, RL = 2 kW 2 150 2.5 2 50 -123 V/ms kHz ms MHz Degrees dB 0.1 Hz to 10 Hz f = 1 kHz f = 1 kHz f = 10 kHz, RL = 0, AV = +1 2 16 0.8 0.005 mV p-p nV//Hz fA//Hz % -2- REV. C AD824 ELECTRICAL SPECIFICATIONS (@ V = 15.0 V, V S Parameter Symbol INPUT CHARACTERISTICS Offset Voltage AD824A VOS Input Bias Current IB Input Offset Current IB IOS OUT = 0 V, TA = 25C unless otherwise noted) Conditions Min TMIN to TMAX VCM = 0 V TMIN to TMAX VCM = -10 V TMIN to TMAX Input Voltage Range Common-Mode Rejection Ratio Input Impedance Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High CMRR AVO DVOS/DT VOH Output Voltage Low VOL Short Circuit Limit Open-Loop Impedance ISC ZOUT POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier PSRR ISY Max Unit 0.5 0.6 4 500 25 3 500 2.5 4.0 35 4000 10133.3 mV mV pA pA pA pA pA V dB dB WpF 20 VCM = -15 V to 13 V TMIN to TMAX -15 70 66 Vo = -10 V to +10 V; RL = 2 kW RL = 10 kW RL = 100 kW TMIN to TMAX, RL = 100 kW 12 50 300 200 50 200 2000 1000 2 V/mV V/mV V/mV V/mV mV/C ISOURCE = 20 mA TMIN to TMAX ISOURCE = 2.5 mA TMIN to TMAX ISINK = 20 mA TMIN to TMAX ISINK = 2.5 mA TMIN to TMAX Sink/Source, TMIN to TMAX f = 1 MHz, AV = 1 14.975 14.970 14.80 14.75 14.988 14.985 14.85 14.82 -14.985 -14.98 -14.88 -14.86 20 100 V V V V V V V V mA W VS = 2.7 V to 15 V TMIN to TMAX VO = 0 V TMIN to TMAX 70 68 DYNAMIC PERFORMANCE Slew Rate Full-Power Bandwidth Settling Time Gain Bandwidth Product Phase Margin Channel Separation SR BWP tS GBP fo CS RL = 10 kW, AV = 1 1% Distortion, VO = 20 V p-p VOUT = 0 V to 10 V, to 0.01% NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density Total Harmonic Distortion en p-p en in THD 0.1 Hz to 10 Hz f = 1 kHz f = 1 kHz f =10 kHz, VO = 3 V rms, RL = 10 kW REV. C Typ f = 1 kHz, RL =2 kW -3- 8 13 80 -14.975 -14.97 -14.85 -14.8 80 560 625 675 dB dB mA mA 2 33 6 2 50 -123 V/ms kHz ms MHz Degrees dB 2 16 1.1 mV p-p nV//Hz fA//Hz 0.005 % AD824-SPECIFICATIONS ELECTRICAL SPECIFICATIONS (@ VS = 3.0 V, VCM = 0 V, VOUT = 0.2 V, TA = 25C unless otherwise noted) Parameter Symbol INPUT CHARACTERISTICS Offset Voltage AD824A -3 V VOS Conditions Min Typ Max Unit 0.2 1.0 1.5 12 4000 10 10133.3 mV mV pA pA pA pA V dB dB WpF TMIN to TMAX Input Bias Current IB 2 250 2 250 TMIN to TMAX Input Offset Current IOS TMIN to TMAX Input Voltage Range Common-Mode Rejection Ratio Input Impedance Large Signal Voltage Gain Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage High CMRR AVO DVOS/DT VOH Output Voltage Low VOL Short Circuit Limit ISC ISC ZOUT Open-Loop Impedance POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier PSRR ISY VCM = 0 V to 1 V TMIN to TMAX 0 58 56 VO = 0.2 V to 2.0 V RL = 2 kW RL = 10 kW RL = 100 kW TMIN to TMAX, RL = 100 kW 10 30 180 90 20 65 500 250 2 V/mV V/mV V/mV V/mV mV/C ISOURCE = 20 mA TMIN to TMAX ISOURCE = 2.5 mA TMIN to TMAX ISINK = 20 mA TMIN to TMAX ISINK = 2.5 mA TMIN to TMAX Sink/Source Sink/Source, TMIN to TMAX f = 1 MHz, AV = 1 2.975 2.97 2.8 2.75 2.988 2.985 2.85 2.82 15 20 120 140 8 6 100 V V V V mV mV mV mV mA mA W VS = 2.7 V to 12 V, TMIN to TMAX VO = 0.2 V, TMIN to TMAX 70 66 DYNAMIC PERFORMANCE Slew Rate Full-Power Bandwidth Settling Time Gain Bandwidth Product Phase Margin Channel Separation SR BWP tS GBP fo CS RL =10 kW, AV = 1 1% Distortion, VO = 2 V p-p VOUT = 0.2 V to 2.5 V, to 0.01% NOISE PERFORMANCE Voltage Noise Voltage Noise Density Current Noise Density Total Harmonic Distortion en p-p en in THD 0.1 Hz to 10 Hz f = 1 kHz f = 1 kHz, RL = 2 kW f = 10 kHz, RL = 0, AV = +1 -4- 1 74 500 25 30 150 200 600 dB dB mA 2 300 2 2 50 -123 V/ms kHz ms MHz Degrees dB 2 16 0.8 0.01 mV p-p nV//Hz fA//Hz % REV. C AD824 WAFER TEST LIMITS (@ V = 5.0 V, V S CM = 0 V, TA = 25C unless otherwise noted) Parameter Symbol Offset Voltage Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Ratio Power Supply Rejection Ratio Large Signal Voltage Gain Output Voltage High Output Voltage Low Supply Current/Amplifier VOS IB IOS VCM CMRR PSRR AVO VOH VOL ISY Conditions Limit Unit VCM = 0 V to 2 V V = + 2.7 V to +12 V RL = 2 kW ISOURCE = 20 mA ISINK = 20 mA VO = 0 V, RL = * 1.0 12 20 -0.2 to 3.0 66 70 15 4.975 25 600 mV max pA max pA V min dB min mV/V V/mV min V min mV max mA max NOTE Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing. ABSOLUTE MAXIMUM RATINGS 1 VCC Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . -VS - 0.2 V to +VS Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . 30 V Output Short Circuit Duration to GND . . . . . . . . . Indefinite Storage Temperature Range R-14, R-16 Packages . . . . . . . . . . . . . . . . -65C to +150C Operating Temperature Range AD824A . . . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C Junction Temperature Range R-14, R-16 Packages . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering 60 sec) . . . . . . . . . 300C Package Type 14-Lead SOIC (R) 16-Lead SOIC (R) qJA2 qJC Unit 120 92 36 27 C/W C/W I5 R1 Package Description AD824AR-14 AD824AR-14-3V AD824AR-16 -40C to +85C 14-Pin SOIC -40C to +85C 14-Pin SOIC -40C to +85C 16-Pin SOIC +IN J1 Q6 C3 Q5 J2 R13 Q20 Q19 R7 Q7 R15 Q23 Q22 C2 -IN C4 VOUT Q24 Q25 Q8 C1 Q2 Q3 Q31 R12 I1 R14 I2 R17 I3 Q28 Q26 I4 VEE Figure 1. Simplified Schematic of 1/4 AD824 Package Option R-14 R-14 R-16 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD824 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. C Q29 Q21 Q27 Q4 ORDERING GUIDE Temperature Range Q18 R9 NOTES 1 Absolute maximum ratings apply to packaged parts unless otherwise noted. 2 qJA is specified for the worst case conditions, i.e., qJA is specified for device in socket for P-DIP packages; qJA is specified for device soldered in circuit board for SOIC package. Model I6 R2 -5- WARNING! ESD SENSITIVE DEVICE AD824 -Typical Performance Characteristics VS = 15V NO LOAD 80 40 45 90 20 135 180 0 100 1k 10k 100k 1M 40 45 90 20 135 180 0 10M 100 100 90 1k 10k 100k 1M PHASE - Degrees GAIN - dB 60 PHASE - Degrees 10M 100 90 10 10 0% 0% 50mV 1s 50mV TPC 1. Open-Loop Gain/Phase and Small Signal Response, VS = 15 V, No Load TPC 3. Open-Loop Gain/Phase and Small Signal Response, VS = 5 V, No Load VS = 15V CL = 100pF 80 1s VS = 5V CL = 220pF 60 60 GAIN - dB 40 45 90 20 135 180 0 100 1k 10k 100k 1M PHASE - Degrees 40 45 90 20 135 180 0 PHASE - Degrees GAIN - dB 60 GAIN - dB VS = 5V NO LOAD 80 -20 10M 1k 10k 100k 1M 10M 100 90 100 90 10 10 0% 0% 50mV 50mV 1s TPC 2. Open-Loop Gain/Phase and Small Signal Response, VS = 15 V, CL = 100 pF 1s TPC 4. Open-Loop Gain/Phase and Small Signal Response, VS = 5 V, CL = 220 pF -6- REV. C AD824 VS = 3V NO LOAD 60 t 45 90 20 135 180 0 9.950s 100 90 PHASE - Degrees GAIN - dB 40 10 0% -20 5V 1k 10k 100k 1M 2s 10M t 100 90 10.810s 100 90 10 10 0% 0% 50mV 1s 5V TPC 5. Open-Loop Gain/Phase and Small Signal Response, VS = 3 V, No Load TPC 7. Slew Rate, RL = 10k VS = 3V CL = 220pF 60 2s 100 90 45 90 20 135 180 0 PHASE - Degrees GAIN - dB 40 VOUT 10 0% 5V 100s TPC 8. Phase Reversal with Inputs Exceeding Supply by 1 V -20 1k 10k 100k 1M 10M 0.8 OUTPUT TO RAIL - Volts 0.7 100 90 10 0.6 0.5 SOURCE 0.4 0.3 0.2 SINK 0% 50mV 0.1 1s 0 1 TPC 6. Open-Loop Gain/Phase and Small Signal Response, VS = 3 V, CL = 220 pF REV. C 5 10 50 100 500 LOAD CURRENT - A 1m 5m 10m TPC 9. Output Voltage to Supply Rail vs. Sink and Source Load Currents -7- AD824 14 COUNT = 60 3V VS 15V 10 60 NUMBER OF UNITS NOISE DENSITY - nV/ Hz 12 40 20 8 6 4 2 5 10 15 FREQUENCY - kHz 20 0 -2.5 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 OFFSET VOLTAGE DRIFT 2.0 2.5 TPC 13. TC VOS Distribution, -55C to +125C, VS = 5, 0 TPC 10. Voltage Noise Density 150 0.1 VS = 5, 0 RL = 0 AV = +1 INPUT OFFSET CURRENT - pA 125 VS = +3 THD+N - % 0.010 VS = +5 0.001 VS = 15 100 75 50 25 0 0.0001 20 100 1k FREQUENCY - Hz 10k -25 -60 20k -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE - C TPC 14. Input Offset Current vs. Temperature TPC 11. Total Harmonic Distortion 280 100k VS = 5, 0 COUNT = 860 10k INPUT BIAS CURRENT - pA NUMBER OF UNITS 240 200 160 1k 100 120 80 40 0 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 OFFSET VOLTAGE - mV 0.3 0.4 0.5 10 1 20 40 60 80 100 TEMPERATURE - C 120 140 TPC 15. Input Bias Current vs. Temperature TPC 12. Input Offset Distribution, VS = 5, 0 -8- REV. C AD824 1k 100 INPUT VOLTAGE NOISE - nV//Hz COMMON-MODE REJECTION - dB 120 80 60 40 20 0 10 100 1k 10k 100k FREQUENCY - Hz 1M POWER SUPPLY REJECTION - dB -80 -100 -120 100 1k 10k FREQUENCY - Hz 100 1k FREQUENCY - Hz 10k 100k 100 80 60 40 20 0 10 100k TPC 17. THD vs. Frequency, 3 V rms 30 80 80 25 60 60 40 3, 0V 20 20 0 0 100 1k 10k 100k FREQUENCY - Hz 1M OUTPUT VOLTAGE - Volts 15V PHASE MARGIN - Degrees 100 40 100 1k 10k 100k FREQUENCY - Hz 1M 10M TPC 20. Power Supply Rejection vs. Frequency 100 20 15 10 5 -20 10M 0 1k TPC 18. Open-Loop Gain and Phase vs. Frequency REV. C 10 120 -60 -20 10 1 TPC 19. Input Voltage Noise Spectral Density vs. Frequency -40 THD - dB 10 1 10M TPC 16. Common-Mode Rejection vs. Frequency OPEN-LOOP GAIN - dB 100 3k 10k 30k 100k INPUT FREQUENCY - Hz 300k 1M TPC 21. Large Signal Frequency Response -9- AD824 -80 -90 CROSSTALK - dB 5V -100 5s 100 90 -110 1 TO 4 -120 1 TO 3 1 TO 2 10 0% -130 -140 10 1k FREQUENCY - Hz 100 10k 100k TPC 22. Crosstalk vs. Frequency TPC 25. Large Signal Response 2750 10k 2500 1k SUPPLY CURRENT - A OUTPUT IMPEDANCE - VS = 15V 100 10 1 2250 2000 VS = 3, 0 1750 1500 .1 1250 .01 10 1k 100 10k 100k FREQUENCY - Hz 1M 1000 -60 10M TPC 23. Output Impedance vs. Frequency, Gain = +1 -40 -20 0 20 40 60 80 TEMPERATURE - C 100 120 140 TPC 26. Supply Current vs. Temperature 20mV OUTPUT SATURATION VOLTAGE - mV 1000 500ns 100 90 10 0% VS = 15V VS = 3, 0 100 VOL - VS 10 0 0.01 TPC 24. Small Signal Response, Unity Gain Follower, 10k100 pF Load VS - VOH 0.10 1.0 LOAD CURRENT - mA 10.0 TPC 27. Output Saturation Voltage -10- REV. C AD824 APPLICATION NOTES INPUT CHARACTERISTICS In the AD824, n-channel JFETs are used to provide a low offset, low noise, high impedance input stage. Minimum input common-mode voltage extends from 0.2 V below -VS to 1 V less than +VS. Driving the input voltage closer to the positive rail will cause a loss of amplifier bandwidth. The AD824 does not exhibit phase reversal for input voltages up to and including +VS. Figure 2a shows the response of an AD824 voltage follower to a 0 V to 5 V (+VS) square wave input. The input and output are superimposed. The output tracks the input up to +VS without phase reversal. The reduced bandwidth above a 4 V input causes the rounding of the output wave form. For input voltages greater than +VS, a resistor in series with the AD824's noninverting input will prevent phase reversal at the expense of greater input voltage noise. This is illustrated in Figure 2b. 1V 2s 100 90 0% (a) 1V The AD824's unique bipolar rail-to-rail output stage swings within 15 mV of the positive and negative supply voltages. The AD824's approximate output saturation resistance is 100 W for both sourcing and sinking. This can be used to estimate output saturation voltage when driving heavier current loads. For instance, the saturation voltage will be 0.5 V from either supply with a 5 mA current load. Direct capacitive loads will interact with the amplifier's effective output impedance to form an additional pole in the amplifier's feedback loop, which can cause excessive peaking on the pulse response or loss of stability. Worst case is when the amplifier is used as a unity gain follower. TPC 4 and 6 show the AD824's pulse response as a unity gain follower driving 220 pF. Configurations with less loop gain, and as a result less loop bandwidth, will be much less sensitive to capacitance load effects. Noise gain is the inverse of the feedback attenuation factor provided by the feedback network in use. 10s 1V 100 90 10 GND OUTPUT CHARACTERISTICS If the AD824's output is overdriven so as to saturate either of the output devices, the amplifier will recover within 2 ms of its input returning to the amplifier's linear operating region. 1V +VS Input voltages less than -VS are a completely different story. The amplifier can safely withstand input voltages 20 V below the minus supply voltage as long as the total voltage from the positive supply to the input terminal is less than 36 V. In addition, the input stage typically maintains picoamp level input currents across that input voltage range. For load resistances over 20 kW, the AD824's input error voltage is virtually unchanged until the output voltage is driven to 180 mV of either supply. 10 GND A current-limiting resistor should be used in series with the input of the AD824 if there is a possibility of the input voltage exceeding the positive supply by more than 300 mV or if an input voltage will be applied to the AD824 when VS = 0. The amplifier will be damaged if left in that condition for more than 10 seconds. A 1 kW resistor allows the amplifier to withstand up to 10 V of continuous overvoltage and increases the input voltage noise by a negligible amount. 0% 1V (b) Figure 3 shows a method for extending capacitance load drive capability for a unity gain follower. With these component values, the circuit will drive 5,000 pF with a 10% overshoot. +5V RP VIN VOUT +VS 0.01F 8 VIN Figure 2. (a) Response with RP = 0; VIN from 0 to +VS (b) VIN = 0 to + VS + 200 m V VOUT = 0 to + VS RP = 49.9 kW Since the input stage uses n-channel JFETs, input current during normal operation is positive; the current flows out from the input terminals. If the input voltage is driven more positive than +VS - 0.4 V, the input current will reverse direction as internal device junctions become forward biased. This is illustrated in TPC 8. REV. C 100 1/4 AD824 VOUT 0.01F 4 CL -VS 20pF 20k Figure 3. Extending Unity Gain Follower Capacitive Load Capability Beyond 350 pF -11- AD824 APPLICATIONS Single Supply Voltage-to-Frequency Converter Table I. AD824 In Amp Performance The circuit shown in Figure 4 uses the AD824 to drive a low power timer, which produces a stable pulse of width t1. The positive going output pulse is integrated by R1-C1 and used as one input to the AD824, which is connected as a differential integrator. The other input (nonloading) is the unknown voltage, VIN. The AD824 output drives the timer trigger input, closing the overall feedback loop. 10V C5 0.1F U4 REF02 2 6 VREF = 5V 5 3 RSCALE** 10k 4 CMOS 74HCO4 U3B 4 3 U1 C1 499k, 1% 0V TO 2.5V FULL SCALE C2 0.01F, 2% VS = 5 V CMRR Common-Mode Voltage Range 3 dB BW, G = 10 G = 100 tSETTLING 2 V Step (VS = 0 V, 3 V) 5 V (VS = 5 V) Noise @ f = 1 kHz, G = 10 G = 100 74 dB 80 dB -0.2 V to +2 V -5.2 V to +4 V 180 kHz 180 kHz 18 kHz 18 kHz 2 ms 5 ms 270 nV//Hz 2.2 mV//Hz 270 nV//Hz 2.2 mV//Hz OUT2 U3A 2 1 5s 100 90 OUT1 U2 CMOS 555 R3* 116k 1/4 R1 VS = 3 V, 0 V C3 0.1F 0.01F, 2% R2 499k, 1% Parameters 4 R 6 THR 8 V+ OUT 3 2 TR AD824 10 CV 5 7 DIS C6 390pF 5% (NPO) 0% 1V GND 1 C4 0.1F Figure 5a. Pulse Response of In Amp to a 500 mV p-p Input Signal; VS = 5 V, 0 V; Gain = 10 NOTES fOUT = V IN/(VREF t1), t1 = 1.1 R3 C6 = 25kHz fS AS SHOWN. * = 1% METAL FILM, <50ppm/C TC VREF ** = 10%, 20T FILM, <100ppm/C TC R1 R2 R3 R4 R5 R6 90k 9k 1k 1k 9k 90k OHMTEK PART # 1043 t1 = 33s FOR fOUT = 20kHz @ V IN = 2.0V G = 10 Figure 4. Single Supply Voltage-to-Frequency Converter Typical AD824 bias currents of 2 pA allow megaohm-range source impedances with negligible dc errors. Linearity errors on the order of 0.01% full scale can be achieved with this circuit. This performance is obtained with a 5 V single supply, which delivers less than 3 mA to the entire circuit. G = 100 G = 100 G = 10 +VS 0.1F 2 6 1/4 VIN1 RP 1k Single Supply Programmable Gain Instrumentation Amplifier VIN2 The AD824 can be configured as a single supply instrumentation amplifier that is able to operate from single supplies down to 5 V or dual supplies up to 15 V. AD824 FET inputs' 2 pA bias currents minimize offset errors caused by high unbalanced source impedances. 3 1/4 1 AD824 5 AD824 11 7 VOUT RP 1k (G = 10) V OUT = (VIN1 - V IN2) (1+ R6 R4 + R5 (G = 100) V OUT = (VIN1 - V IN2) (1+ ) + V REF R5 + R6 R4 ) + V REF FOR R1 = R6, R2 = R5 AND R3 = R4 An array of precision thin-film resistors sets the in amp gain to be either 10 or 100. These resistors are laser-trimmed to ratio match to 0.01% and have a maximum differential TC of 5 ppm/C. Figure 5b. A Single Supply Programmable Instrumentation Amplifier -12- REV. C AD824 3 Volt, Single Supply Stereo Headphone Driver The AD824 exhibits good current drive and THD+N performance, even at 3 V single supplies. At 1 kHz, total harmonic distortion plus noise (THD+N) equals -62 dB (0.079%) for a 300 mV p-p output signal. This is comparable to other single supply op amps that consume more power and cannot run on 3 V power supplies. In Figure 6, each channel's input signal is coupled via a 1 mF Mylar capacitor. Resistor dividers set the dc voltage at the noninverting inputs so that the output voltage is midway between the power supplies (1.5 V). The gain is 1.5. Each half of the AD824 can then be used to drive a headphone channel. A 5 Hz high-pass filter is realized by the 500 mF capacitors and the headphones, which can be modeled as 32 ohm load resistors to ground. This ensures that all signals in the audio frequency range (20 Hz-20 kHz) are delivered to the headphones. 3V 0.1F 0.1F 95.3k 1F CHANNEL 1 1/4 MYLAR AD824 AD824 47.5k 95.3k 500F L 4.99k 10k HEADPHONES 32 IMPEDANCE 10k of 4.5 V can be used to drive an A/D converter front end. The other half of the AD824 is configured as a unity-gain inverter and generates the other bridge input of -4.5 V. Resistors R1 and R2 provide a constant current for bridge excitation. The AD620 low power instrumentation amplifier is used to condition the differential output voltage of the bridge. The gain of the AD620 is programmed using an external resistor RG and determined by: G= A 3.3 V/5 V Precision Sample-and-Hold Amplifier In battery-powered applications, low supply voltage operational amplifiers are required for low power consumption. Also, low supply voltage applications limit the signal range in precision analog circuitry. Circuits like the sample-and-hold circuit shown in Figure 8, illustrate techniques for designing precision analog circuitry in low supply voltage applications. To maintain high signal-to-noise ratios (SNRs) in a low supply voltage application requires the use of rail-to-rail, input/output operational amplifiers. This design highlights the ability of the AD824 to operate rail-to-rail from a single 3 V/5 V supply, with the advantages of high input impedance. The AD824, a quad JFET-input op amp, is well suited to S/H circuits due to its low input bias currents (3 pA, typical) and high input impedances (3 1013 W, typical). The AD824 also exhibits very low supply currents so the total supply current in this circuit is less than 2.5 mA. 3.3/5V 3.3/5V R R1 50k 4.99k 1/4 47.5k 1F AD824 AD824 CHANNEL 2 49.4 kW +1 RG R2 50k 500F MYLAR AD824A 3 0.1F 4 1 A1 2 A1 FALSE GROUND (FG) 11 R4 2k 3.3/5V 13 Figure 6. 3 Volt Single Supply Stereo Headphone Driver Low Dropout Bipolar Bridge Driver R5 2k The AD824 can be used for driving a 350 ohm Wheatstone bridge. Figure 7 shows one half of the AD824 being used to buffer the AD589--a 1.235 V low power reference. The output +VS 6 1 350 350 3 1/4 1/4 12 SAMPLE/ HOLD 5 VREF -4.5V +VS 0.1F +5V 1F GND -VS 0.1F -VS A4 A4 14 4 5 8 AD824C + V - OUT C 500pF FG Figure 8. 3.3 V/5.5 V Precision Sample and Hold 4 -VS R2 20 13 FG A3 6 AD824 AD620 RG 6 8 7 1% AD824 AD824 7 AD824D 2 1F -5V In many single supply applications, the use of a false ground generator is required. In this circuit, R1 and R2 divide the supply voltage symmetrically, creating the false ground voltage at one-half the supply. Amplifier A1 then buffers this voltage creating a low impedance output drive. The S/H circuit is configured in an inverting topology centered around this false ground level. Figure 7. Low Dropout Bipolar Bridge Driver REV. C 3 10 +VS 10k 1% 2 TO A/D CONVERTER REFERENCE INPUT 26.4k, 1% 350 CH 500pF FG 7 9 1/4 1/4 AD824 AD824 350 10k A2 A2 ADG513 9 R1 20 +1.235V 1% 10 \ 49.9k 10k 14 16 11 AD824B 5 AD589 15 -13- AD824 A design consideration in sample-and-hold circuits is voltage droop at the output caused by op amp bias and switch leakage currents. By choosing a JFET op amp and a low leakage CMOS switch, this design minimizes droop rate error to better than 0.1 mV/ms in this circuit. Higher values of CH will yield a lower droop rate. For best performance, CH and C2 should be polystyrene, polypropylene or Teflon capacitors. These types of capacitors exhibit low leakage and low dielectric absorption. Additionally, 1% metal film resistors were used throughout the design. In the sample mode, SW1 and SW4 are closed, and the output is VOUT = -VIN. The purpose of SW4, which operates in parallel with SW1, is to reduce the pedestal, or hold step, error by injecting the same amount of charge into the noninverting input of A3 that SW1 injects into the inverting input of A3. This creates a common-mode voltage across the inputs of A3 and is then rejected by the CMR of A3; otherwise, the charge injection from SW1 would create a differential voltage step error that would appear at VOUT. The pedestal error for this circuit is less than 2 mV over the entire 0 V to 3.3 V/5 V signal range. Another method of reducing pedestal error is to reduce the pulse amplitude applied to the control pins. In order to control the ADG513, only 2.4 V are required for the "ON" state and 0.8 V for the "OFF" state. If possible, use an input control signal whose amplitude ranges from 0.8 V to 2.4 V instead of a full range 0 V to 3.3 V/5 V for minimum pedestal error. Other circuit features include an acquisition time of less than 3 ms to 1%; reducing CH and C2 will speed up the acquisition time further, but an increased pedestal error will result. Settling time is less than 300 ns to 1%, and the sample-mode signal BW is 80 kHz. The ADG513 was chosen for its ability to work with 3 V/5 V supplies and for having normallyopen and normallyclosed precision CMOS switches on a dielectrically isolated process. SW2 is not required in this circuit; however, it was used in parallel with SW3 to provide a lower RON analog switch. -14- REV. C AD824 * AD824 SPICE Macro-model 9/94, Rev. A * ARG/ADI * * Copyright 1994 by Analog Devices, Inc. * * Refer to "README.DOC" file for License Statement. Use of this model indicates your acceptance with the terms and provisions in the License Statement. * * Node assignments * noninverting input * | inverting input * | | positive supply * | | | negative supply * | | | | output * | | | | | .SUBCKT AD824 1 2 99 50 25 * * INPUT STAGE & POLE AT 3.1 MHz * R3 5 99 1.193E3 R4 6 99 1.193E3 CIN 1 2 4E-12 C2 5 6 19.229E-12 I1 4 50 108E-6 IOS 1 2 1E-12 EOS 7 1 POLY(1) (12,98) 100E-6 1 J1 4 2 5 JX J2 4 7 6 JX * * GAIN STAGE & DOMINANT POLE * EREF 98 0 (30,0) 1 R5 9 98 2.205E6 C3 9 25 54E-12 G1 98 9 (6,5) 0.838E-3 V1 8 98 -1 V2 98 10 -1 D1 9 10 DX D2 8 9 DX * * COMMON-MODE GAIN NETWORK WITH ZERO AT 1 kHz * R21 11 12 1E6 R22 12 98 100 C14 11 12 159E-12 E13 11 98 POLY(2) (2,98) (1,98) 0 0.5 0.5 * * POLE AT 10 MHz * R23 18 98 1E6 C15 18 98 15.9E-15 REV. C G15 98 18 (9,98) 1E-6 * * OUTPUT STAGE * ES 26 98 (18,98) 1 RS 26 22 500 IB1 98 21 2.404E-3 IB2 23 98 2.404E-3 D10 21 98 DY D11 98 23 DY C16 20 25 2E-12 C17 24 25 2E-12 DQ1 97 20 DQ Q2 20 21 22 NPN Q3 24 23 22 PNP DQ2 24 51 DQ Q5 25 20 97 PNP 20 Q6 25 24 51 NPN 20 VP 96 97 0 VN 51 52 0 EP 96 0 (99,0) 1 EN 52 0 (50,0) 1 R25 30 99 5E6 R26 30 50 5E6 FSY1 99 0 VP 1 FSY2 0 50VN 1 DC1 25 99 DX DC2 50 25 DX * * MODELS USED * .MODEL JX NJF(BETA=3.2526E-3 VTO=-2.000 IS=2E-12) .MODEL NPN NPN(BF=120 VAF=150 VAR=15 RB=2E3 + RE=4 RC=550 IS=1E-16) .MODEL PNP PNP(BF=120 VAF=150 VAR=15 RB=2E3 + RE=4 RC=750 IS=1E-16) .MODEL DX D(IS=1E-15) .MODEL DY D() .MODEL DQ D(IS=1E-16) .ENDS AD824 -15- AD824 14-Lead Standard Small Outline Package [SOIC] Narrow Body (R-14) 16-Lead Standard Small Outline Package [SOIC] Wide Body (R-16) Dimensions shown in millimeters and (inches) Dimensions shown in millimeters and (inches) 8.75 (0.3445) 8.55 (0.3366) 4.00 (0.1575) 3.80 (0.1496) 10.50 (0.4134) 10.10 (0.3976) 14 8 1 7 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 C00875-0-2/03(C) OUTLINE DIMENSIONS 1.27 (0.0500) BSC 0.51 (0.0201) 0.33 (0.0130) 6.20 (0.2441) 5.80 (0.2283) 7.60 (0.2992) 7.40 (0.2913) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 9 16 8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.19 (0.0075) 1.27 (0.0500) BSC 0.30 (0.0118) 0.10 (0.0039) COMPLIANT TO JEDEC STANDARDS MS-012AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COPLANARITY 0.10 10.65 (0.4193) 10.00 (0.3937) 8 1 0.50 (0.0197) 45 0.25 (0.0098) 0.51 (0.0201) 0.33 (0.0130) 0.75 (0.0295) 45 0.25 (0.0098) 2.65 (0.1043) 2.35 (0.0925) SEATING PLANE 0.32 (0.0126) 0.23 (0.0091) 8 0 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-013AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Revision History Location Page 2/03-Data Sheet changed from REV. B to REV. C. Deleted N Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edits to Figure 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Edits to Figure 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Edits to ELECTRICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2, 3 Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Deleted DICE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 -16- REV. C PRINTED IN U.S.A. 1/02-Data Sheet changed from REV. A to REV. B.