Series G3T Process Sealed Ultra-Miniature SMT Toggles
A42
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable Rockers
Touch Tilt
A
Toggles
www.nkkswitches.com
General Specifications
Electrical Capacity (Resistive Load)
Logic Level: 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: See Supplement section for explanation of operating range.
Other Ratings
Contact Resistance: 80 milliohms maximum
Insulation Resistance: 500 megohms minimum @ 500V DC
Dielectric Strength: 500V AC minimum for 1 minute minimum
Mechanical Life: 50,000 operations minimum
Electrical Life: 50,000 operations minimum
Nominal Operating Force: 1.6N for momentary & 1.7N for maintained
Angle of Throw: 28°
Materials & Finishes
Actuator: Polyphenylene sulfide (UL94V-0)
Case: Polyphenylene sulfide (UL94V-0)
Sealing Rings: Nitrile butadiene rubber
Movable Contacts: Phosphor bronze with gold plating
Stationary Contacts: Phosphor bronze with gold plating
Base: Polyphenylene sulfide (UL94V-0)
Terminals: Phosphor bronze with gold plating
Environmental Data
Operating Temperature Range: –30°C through +85°C (–22°F through +185°F)
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Installation
Mounting: It is recommended that the body of models for upright mounting without bracket be fastened to a
panel or similar support for protection of solder joints from mechanical stress.
Coplanarity: See specifications in Terms & Acronyms in Supplement section
Processing
Soldering: Reflow Soldering recommended. See Profile B in Supplement section.
Manual Soldering: See Profile B in Supplement section.
Cleaning: Automated cleaning. See Cleaning specifications in Supplement section.
Standards & Certifications
Flammability Standard: UL94V-0 actuator, case & base
The G3T Series toggles have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Series G3T
Process Sealed Ultra-Miniature SMT Toggles
A43
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable
A
Toggles
Rockers
Touch Tilt
www.nkkswitches.com
Distinctive Characteristics
Actual Size
Ultra-miniature size allows high density mounting, and extremely light
weight of 0.6 gram makes these switches ideal for handheld equipment.
Tape-reel and stick-tube packaging allow rapid automated
placement of surface mount devices. Tape-reel packaging
meets EIA-481-D Standard.
Heat resistant resin used for housing, base, and
lever allows vapor phase and infrared convection
reflow soldering.
Combination of design features achieves total seal and
allows automated processing techniques, including flux
cleaning procedures: one-piece bushing and housing,
rubber seals surrounding actuator and base, epoxy at
joint of case and base, and molded-in, epoxy-sealed
terminals.
Award-winning STC contact mechanism with benefits
unavailable in conventional mechanisms: smoother, positive
detent actuation, increased contact stability and unparalleled logic-level
reliability. (Additional STC details in Terms & Acronyms; see Supplement section.)
Gull-wing terminals provide mechanical stability during soldering and simplified solder
joint inspection.
Coplanarity: all considered surfaces must lie between two parallel planes that are a
maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms
and Acronyms in the Supplement section.)
Series G3T Process Sealed Ultra-Miniature SMT Toggles
A44
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable Rockers
Touch Tilt
A
Toggles
www.nkkswitches.com
Toggle Position
( ) = Momentary Connected Terminals Throw & Schematics
Pole Model
Up Center Down Up Center Down
Note: Terminal numbers are
not actually on switch.
SP
G3T12
G3T13
G3T15
G3T18
G3T19
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
5-6 OPEN 5-4 SPDT
DP
G3T22
G3T23
G3T25
G3T28
G3T29
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
5-6 2-3 OPEN 5-4 2-1 DPDT
(COM)
6
4
5
1
2
3
5 (COM)
6
4
Poles
1SPDT
2DPDT
TYPICAL SWITCH ORDERING EXAMPLE
Circuits
2ON NONE ON
3ON OFF ON
5ON NONE (ON)
8(ON) OFF (ON)
9ON OFF (ON)
( ) = Momentary
Actuator
A.150” (3.8mm)
Column Toggle
1G3T A2 H
Terminals
PGull Wing for Upright Mount
BGull Wing for Upright with Bracket Mount
HGull Wing for Right Angle Mount
Packaging
R
Tape-Reel for
Right Angle Only
500 Pieces/Reel
S
Stick-Tube for
Upright Mount
50 Pieces/Stick
No
Code
Partitioned Tray for
Upright & Right Angle
Any Quantity
Packaging details at
end of G3T Series
ACTUATOR
.150” (3.8mm) Column Toggle
POLES & CIRCUITS
A
Gull Wing Terminals for
Right Angle Mount
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
G3T12AH
.150” (3.8mm)
Column Toggle
SPDT
ON-NONE-ON Circuit
(4.0) Dia
.157
(1.7) Dia
.067
28°
(3.8)
.150
Slot
Slot
Series G3T
Process Sealed Ultra-Miniature SMT Toggles
A45
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable
A
Toggles
Rockers
Touch Tilt
www.nkkswitches.com
TYPICAL SWITCH DIMENSIONS
Right Angle Mounting
Single & Double Pole Upright Mounting with Bracket
G3T12AP
G3T22AB
Single & Double Pole Upright Mounting
G3T12AH
Single Pole Double Pole
Pad Layouts for Upright Mounting Upright Mounting with Bracket Right Angle Mounting
Surface Mount
Terminals
Single Pole
Double Throw
Double Pole
Double Throw
(8.5)
.335
(5.08)
.200
Support Legs
4
5
6
(0.5) Ty
p
.020
(7.6)
.299
(3.8)
.150
(9.0)
.354 (0.1)
.004
(1.5)
.059
(0.7)
.028
28°
(1.7) Dia
.067
(4.0) Dia
.157
(0.25) Typ
.010
(0.6) Typ
.024
Slot
(5.0)
.197
1
2
3
4
5
6
(8.5)
.335
(7.6)
.299
(0.5) Ty
p
.020
Slot
(5.0)
(3.8)
.150
(9.0)
.354
(0.1)
.004
(1.5)
.059
(0.7)
.028
28°
(1.7) Dia
.067
(4.0) Dia
.157
(0.25) Ty
p
.010
(5.08)
.200
Support Legs
(3.8)
.150
(1.2) Typ
.047
4
5
6
(11.0)
.433
(0.5) Ty
p
.020
(0.9) Typ
.035
(7.6)
.299
(3.8)
.150
(1.2) Typ
.047
4
5
6
(11.0)
.433
(0.5) Ty
p
.020
(0.9)
Typ
.035
(7.6)
.299
1
2
3
Slot
(8.5)
.335
(0.25)
Typ
.010
28°
(1.7) Dia
.067
(3.8) Typ
.150
(2.54) Typ
.100 (1.25) Ty
p
.049
(11.0)
.433
(0.5) Typ
.020
(0.9) Typ
.035
(0.55)
.022
(9.0)
.354
(3.8)
.150
(1.5)
.059
(4.0) Dia
.157
(0.25)
.010
654
(5.55)
.219
(0.1)
.004
635241
(5.55)
.219
(0.1)
.004
(1.1) Typ
.043
(3.8)
.150 (1.7) Typ
.067
(2.54) Ty
p
.100
(0.635)
.025
(0.7) Typ
.028
(1.55)
Typ
.061
(3.0)
.118
(9.75)
.384
4
5
6
(1.1) Typ
.043
(3.8)
.150 (1.7) Typ
.067 (1.27) Typ
.050
(0.635) Ty
p
.025
(0.7) Typ
.028
(1.55)
Typ
.061
(3.0)
.118
(9.75)
.384
1
4
2
5
3
6
(1.7) Typ
.067
(3.8)
.150 (1.1) Typ
.043
(1.55) Typ
.061
(0.635)
.025
(0.7) Typ
.028
4
5
6
(2.54)
Typ
.100
Support
Pads
(9.75)
.384
(6.0)
.236
(0.635)
.025
(2.54) Typ
.100
(1.7) Typ
.067
(0.635)
.025
(0.7) Typ
.028
4
5
6
(2.54)
Typ
.100
(6.0)
.236
Support
Pads
(0.635)
.025
(2.54) Ty
p
.100
(1.7) Typ
.067
(0.635)
.025
(0.7) Typ
.028
4
5
6
(2.54)
Typ
.100
(6.0)
.236 (0.635)
.025
(2.54) Ty
p
.100
1
2
3
(1.7) Typ
.067
(3.8)
.150 (1.1) Typ
.043
(1.55) Typ
.061
(0.635) Typ
.025
(0.7) Typ
.028
4
5
6
(2.54)
Typ
.100 (9.75)
.384
(6.0)
.236
1
2
3
(0.635)
.025
(2.54) Typ
.100
Series G3T Process Sealed Ultra-Miniature SMT Toggles
A46
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries Pushbuttons
Illuminated PB
Slides Programmable Rockers
Touch Tilt
A
Toggles
www.nkkswitches.com
PACKAGING
RTape-Reel
for Right Angle
500 pieces per reel
Switches must be ordered in
500-piece increments when
tape-reel packaging is selected.
This packaging meets EIA-481-D
Standard for “16mm and 24mm
Embossed Carrier Taping of
Surface Mount Components
for Automatic Handling.”
Partitioned Tray
for Upright & Right Angle
Any quantity
If the G3 upright models are
ordered in less than 50-piece
increments or the right angle
models in less than 500-piece
increments, the switches are
packaged in a partitioned tray.
No code is required.
No
Code
SStick-Tube
for Upright Mount
50 pieces per stick
Switches must be ordered in
50-piece increments when
stick-tube packaging is selected.
PACKAGING
Series G3T
Process Sealed Ultra-Miniature SMT Toggles
A47
Indicators
AccessoriesSupplement Tactiles KeylocksRotaries PushbuttonsIlluminated PBSlides Programmable
A
Toggles
Rockers
Touch Tilt
www.nkkswitches.com
PACKAGING (CONTINUED)
Tape-Reel Packaging for Right Angle Mount
Each tape-reel of 550 pockets contains 500 switches.
Minimum Leader Length: 7.87” (200mm) Minimum Trailer Length: 1.97” (50mm)
Reel Dimensions Tape Dimensions
Stick-Tube Packaging for Upright Mount
Each stick-tube contains 50 switches.
L = Length
G3T Upright (code P)
18.31” (465mm)
G3T Upright with Bracket (code B)
21.26” (540mm)
Stick-Tube Dimensions
(78.49) Di
a
3.090
(2.0)
.079
(24.4)
.961
(13.0) Dia
.512
(2.0) Typ
.079
(21.0) Dia
.827
Overall Dia (330.0)
13.0
Te
rminal #1
Part No.
Direction of Feed
(2.1) Dia Typ
.083
(1.5) Dia Typ
.059
(4.0) Typ
.157
(16.0) Typ
.630
(2.0) Typ
.079
(1.75)
.069
(11.5)
.453
(24.0)
.945
(6.0)
.236
(0.4)
.016
(17.8)
.701
(8.6)
.339
(13.9)
.547
(1.5) R
.059
(2.0)
.079
(9.8)
.386
(15.3)
.602
(7.7)
.303
L
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
NKK Switches:
G3T13AH G3T13AP G3T15AB-S G3T22AB G3T22AP G3T23AH G3T28AB G3T22AH G3T28AP G3T28AH
G3T25AP-S G3T29AB-S G3T23AB-S G3T25AH-R G3T28AP-S G3T18AP-S G3T22AH-R G3T28AH-R G3T23AB
G3T29AH G3T25AP G3T25AH G3T23AP G3T29AP G3T25AB G3T29AB G3T19AB-S G3T19AP-S G3T18AH-R
G3T12AH G3T12AP G3T25AB-S G3T28AB-S G3T18AB-S G3T18AH G3T18AB G3T15AB G3T19AB G3T15AH
G3T19AH G3T18AP G3T19AP G3T15AP G3T23AP-S G3T15AH-R G3T15AP-S G3T19AH-R G3T29AP-S
G3T13AP-S G3T13AH-R G3T12AB-RO G3T13AB G3T22AP-S-RO G3T22AP-RO G3T29AH-R G3T12AH-R
G3T12AB-S G3T12AP-S G3T22AB-S G3T22AP-S G3T23AH-R G3T12AB