DATE REV ECN APF'D. BY 2/2/06 A2 7458 dM * | 635 [16.13] MAX |~.850 [21.59] MAX \ 550 [13.97] MAX | | D =.125 [3.17}.010 [0.25] t NOTES: | . cath RY wo gee DAD [1.02]+| - CONTACTS/SHIELD: COPPER ALLOY SHIELD PLATING: NICKEL OR TIN CONTACT PLATING: SELECTIVE GOLD IN CONTACT AREA [<a Z I SEE CHART FOR PART NUMBER z 2. FOR PRODUCT SPEGFICATIONS SEE PRO22-(i. = a 3, TOLERANCES COMPLY WITH F.C.C. DIMENSION RECUIREMENTS. uf S 4, THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE LU f -D25 [0.64] x USER THE ABILITY TO HAVE REASONABLE JACK/PANEL ( | 100 [2.54] TYP mp CLEARANCES, YET MAINTAIN GROUNDING GAPAEILITY. Bameeen NON-ACQUM Si THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION 9.035 [0.89] (8) | = BUT MAY GARRY SOME CONSEQUENCES IN THE FORM OF yay By 7 a LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. + 4 2 + 6 a +444 ae =i 30 MICRO-INCHES [0.76um] SS7288SFR1A-NF-1 128 128 [3.25] (2) 1 #125 [318] PART NUMHER .120 [3.05] CONTACT PLATING IN MATING AREA #.062 [1.57] (2) _ er THIRD ANGLE PROJECTION Bel Stewart Connector *610 [15.49] 11118 Susquehanna Trail South REV. 6/3/05 P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED @ = Glen Rock, PA 17527-9199 (717) 235-7512 Fox: (717) 235-7954 _ http: //www.stewartconnector.com DO NOT SCALE DRAWING DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE EIGHT CONTACT, EIGHT POSITION, SHIELDED FILTER JACK DIMENSIONS: INCHES [METRIC] UNLESS OTHERWISE SPECIFIED TOLERANCES ARE +.005 [0.13] ANGLES ARE + 1 HETNA 4 OF 2 THSS DRAWING AND THE SUBJECT WATIER SHOWN THEREON | DRM BY: DATE ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF KRL 2/ 2/ 06 BEL STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, | APD BY WM GATE 9-3-06 COPED, OR USED IN ANY MANNER WITHOUT PRR WRITTEN CONSENT OF BEL STEWART CONNECTOR. THE SUBUECT DWE NO. REV. MATTER MAY BE PATENTED GR A PATENT MAY BE PENDING. CT720015 { AutoCADREV. 6/3/05 OHMS FERRITE MATERIAL CHARACTERISTICS FERRITE NOISE INITIAL VOLUME MATERIAL SUPPRESSION | PERMEABILITY | RESISTIVITY DESIGNATION RANGE @B<10gouss| OHM-CM. 30 MHz 500 FRI TO TO >108 200 MHz 1500 200 we 180 oF = 160 mal A Lr 140 A NG. y vT 120 1 Tp 100 7 mie 80 ye ae 60 UM ya 1 40 I r rT | | LL < CAT LEH 20 bes 0 1 10 100 1000 MHz IMPEDANCE CURVE for 7288FR1 INSERT AVERAGE IMPEDANCE CURVE wnonnnn- MAX. & MIN. IMPEDANCE CURVES NOTE: MAXIMUM AND MINIMUM IMPEDANCE VALUES ARE DEPENDENT ON: 1) HOLE POSITION WITHIN THE INSERTS GEOMETRY, AND 2) FERRITE MATERIALS IMPEDANCE VALUE TOLERANCE OF +25% 30 MICRO-INCHES [0.76um] SS-7288SFR1I-A-NF-1 CONTACT PLATING IN MATING AREA PART NUMBER THIRD ANGLE PROJECTION @ = Bel Stewart Connector 11118 Susquehanna Trail South Glen Rock, PA 17527-9199 (717) 235-7512 Fox: (717) 235-7954 http: //www.stewartconnector.com DO NOT SCALE DRAWING DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE EIGHT CONTACT, EIGHT POSITION, SHIELDED FILTER JACK DIMENSIONS: INCHES [METRIC] UNLESS OTHERWISE SPECIFIED TOLERANCES ARE +.005 [0.13] ANGLES ARE + 1 SETNO > OF 2 THIS DRAWING AND THE SUBVECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF BEL STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, COPED, OR USED IN ANY MANNER WITHOUT PRR WRITTEN CONSENT OF BEL STEWART CONNECTOR. THE SUBUECT MATTER MAY BE PATENTED GR A PATENT MAY BE PENDING. mer KRL | 2/2/06 APPD BY: M | "9-3-06 DWE NO, REV. CT720015 A2 1 AutoCAD