BCR25RM-12LB Triac Medium Power Use REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Features * * * * * The product guaranteed maximum junction temperature of 150C * Insulated Type * Planar Type IT (RMS) : 25 A VDRM: 600 V IFGTI, IRGTI, IRGTIII: 50 mA Viso: 2000 V Outline RENESAS Package code: PRSS0003ZA-A (Package name: TO-3PFM) 2 1. T1 Terminal 2. T2 Terminal 3. Gate Terminal 3 1 1 2 3 Applications Contactless AC switch, electric heater control, light dimmer, on/off and speed control of small induction motor, on/off control of copier lamp Maximum Ratings Parameter Symbol Note1 Repetitive peak off-state voltage Note1 Non-repetitive peak off-state voltage Notes: 1. Gate open. REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 1 of 7 VDRM VDSM Voltage class 12 600 720 Unit V V BCR25RM-12LB Symbol Ratings Unit RMS on-state current Parameter IT (RMS) 25 A Surge on-state current ITSM 250 A I2t 313 A2s PGM PG (AV) VGM IGM Tj Tstg -- Viso 5 0.5 10 2 -40 to +150 -40 to +150 5.2 2000 W W V A C C g V I2t for fusion Peak gate power dissipation Average gate power dissipation Peak gate voltage Peak gate current Junction Temperature Storage temperature Mass Isolation voltage Conditions Commercial frequency, sine full wave 360 conduction, Tc = 96C 50 Hz sinewave 1 full cycle, peak value, non-repetitive Value corresponding to 1 cycle of half wave 50 Hz, surge on-state current Typical value Ta = 25C, AC 1 minute, T1*T2*G terminal to case Electrical Characteristics Parameter Repetitive peak off-state current On-state voltage Symbol IDRM VTM Min. -- -- Typ. -- -- Max. 3.0/5.0 1.5 Unit mA V Test conditions Tj = 125C /150C, VDRM applied Tc = 25C, ITM = 40 A, instantaneous measurement Gate trigger voltageNote2 VFGT VRGT VRGT -- -- -- -- -- -- 2.0 2.0 2.0 V V V Tj = 25C, VD = 6 V, RL = 6 , RG = 330 Gate trigger curentNote2 IFGT IRGT IRGT -- -- -- -- -- -- 50 50 50 mA mA mA Tj = 25C, VD = 6 V, RL = 6 , RG = 330 VGD Rth (j-c) 0.2/0.1 -- -- -- -- 1.7 V C/W Tj = 125C /150C, VD = 1/2 VDRM Junction to caseNote3 (dv/dt)c 10/1 -- -- V/s Tj = 125C /150C Gate non-trigger voltage Thermal resistance Critical-rate of rise of off-state Note4 commutation voltage Notes: 2. Measurement using the gate trigger characteristics measurement circuit. 3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5C/W. 4. Test conditions of the critical-rate of rise of off-state commutation voltage is shown in the table below. Test conditions 1. Junction temperature Tj = 125/150C 2. Rate of decay of on-state commutating current (di/dt)c = -13 A/ms 3. Peak off-state voltage VD = 400 V REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 2 of 7 Commutating voltage and current waveforms (inductive load) Supply Voltage Time Main Current (di/dt)c Time Main Voltage (dv/dt)c Time VD BCR25RM-12LB Performance Curves Maximum On-State Characteristics Rated Surge On-State Current Surge On-State Current (A) 400 102 Tj = 150C 101 Tj = 25C 100 0.5 1.0 1.5 2.0 2.5 3.0 102 VGT = 2.0 V PGM = 5 W PG(AV) = 0.5 W IGM = 2 A 100 7 5 3 2 VGD = 0.1 V 5 7103 2 3 5 7104 103 Typical Example 102 IFGT I IRGT I IRGT III 101 -40 0 40 80 120 160 Gate Current (mA) Junction Temperature (C) Gate Trigger Voltage vs. Junction Temperature Maximum Transient Thermal Impedance Characteristics (Junction to case) 103 Typical Example 102 101 -40 Gate Trigger Current (Tj = 25C) VGM = 10 V x 100 (%) Gate Trigger Current vs. Junction Temperature 0 40 80 120 Junction Temperature (C) REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 3 of 7 160 Transient Thermal Impedance (C/W) Gate Voltage (V) x 100 (%) Gate Trigger Voltage (Tj = tC) 101 Gate Characteristics (I, II and III) 10-1 IFGT I, IRGT I, IRGT III 7 5 1 10 2 3 5 7 102 2 3 Gate Trigger Voltage (Tj = 25C) 100 Conduction Time (Cycles at 50 Hz) 3 2 3 2 200 On-State Voltage (V) 5 101 7 5 300 0 100 3.5 Gate Trigger Current (Tj = tC) On-State Current (A) 103 102 2.0 103 104 100 101 1.8 1.6 1.4 1.2 1.0 0.8 0.6 1.4 1.0 0 10-1 102 Conduction Time (Cycles at 50 Hz) BCR25RM-12LB Allowable Case Temperature vs. RMS On-State Current Maximum On-State Power Dissipation 160 20 10 360 Conduction Resistive, inductive loads 0 10 40 80 60 40 360 Conduction 20 Resistive, inductive loads 0 0 10 20 30 40 Allowable Ambient Temperature vs. RMS On-State Current Allowable Ambient Temperature vs. RMS On-State Current 160 140 100 Curves apply regardless of conduction angle Resistive, inductive loads Natural convection 80 160 160 t2.3 120 60 Ambient Temperature (C) All fins are blackpainted aluminum and greased 120 120 t2.3 40 100 100 t2.3 20 10 20 30 120 100 80 60 40 20 0 1 2 3 4 5 RMS On-State Current (A) Breakover Voltage vs. Junction Temperature Repetitive Peak Off-State Current vs. Junction Temperature Typical Example 102 0 40 80 120 Junction Temperature (C) REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 4 of 7 160 x 100 (%) RMS On-State Current (A) 103 101 -40 Natural convection No Fins Curves apply regardless of conduction angle Resistive, inductive loads 140 0 40 Repetitive Peak Off-State Current (Tj = tC) Ambient Temperature (C) 30 100 RMS On-State Current (A) 0 0 x 100 (%) 20 120 RMS On-State Current (A) 160 Breakover Voltage (Tj = tC) Case Temperature (C) 30 0 Breakover Voltage (Tj = 25C) Curves apply regardless of conduction angle 140 Repetitive Peak Off-State Current (Tj = 25C) On-State Power Dissipation (W) 40 106 Typical Example 105 104 103 102 -40 0 40 80 120 Junction Temperature (C) 160 BCR25RM-12LB Latching Current vs. Junction Temperature 103 103 Latching Current (mA) Typical Example 102 101 -40 0 40 80 120 T2+, G- Typical Example Distribution 102 101 T2-, G- Typical Example 100 -40 160 T2+, G+ Typical Example 0 40 80 120 160 Junction Temperature (C) Breakover Voltage vs. Rate of Rise of Off-State Voltage (Tj = 125C) Breakover Voltage vs. Rate of Rise of Off-State Voltage (Tj = 150C) 160 Typical Example Tj = 125C 140 120 100 III Quadrant 80 60 40 I Quadrant 20 0 101 102 103 104 Breakover Voltage (dv/dt = xV/s) x 100 (%) Breakover Voltage (dv/dt = 1V/s) Junction Temperature (C) 160 Typical Example Tj = 150C 140 120 100 80 III Quadrant 60 40 I Quadrant 20 0 101 102 103 104 Rate of Rise of Off-State Voltage (V/s) Rate of Rise of Off-State Voltage (V/s) Commutation Characteristics (Tj = 125C) Commutation Characteristics (Tj = 150C) 102 7 5 102 7 5 3 2 Typical Example Tj = 125C IT = 4 A = 500 s VD = 200 V f = 3 Hz Main Voltage (dv/dt)c Time Critical Rate of Rise of Off-State Commutating Voltage (V/s) Holding Current (Tj = tC) Critical Rate of Rise of Off-State Commutating Voltage (V/s) Breakover Voltage (dv/dt = xV/s) x 100 (%) Breakover Voltage (dv/dt = 1V/s) Holding Current (Tj = 25C) x 100 (%) Holding Current vs. Junction Temperature VD Main Current IT (di/dt)c Time I Quadrant 101 7 5 3 2 100 7 3 III Quadrant 5 7 101 2 3 5 7 102 2 Rate of Decay of On-State Commutating Current (A/ms) REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 5 of 7 3 3 2 101 7 5 3 2 Typical Example Tj = 150C IT = 4 A = 500 s VD = 200 V f = 3 Hz Main Voltage (dv/dt)c Time VD Main Current IT (di/dt)c Time III Quadrant I Quadrant Minimum Characteristics 100 Value 7 3 5 7 101 2 3 5 7 102 2 Rate of Decay of On-State Commutating Current (A/ms) 3 BCR25RM-12LB Gate Trigger Current (tw) Gate Trigger Current (DC) x 100 (%) Gate Trigger Current vs. Gate Current Pulse Width 103 7 5 4 3 2 Typical Example IFGT I IRGT III IRGT I 102 7 5 4 3 2 101 0 10 2 3 4 5 7 101 2 3 4 5 7 102 Gate Current Pulse Width (s) Gate Trigger Characteristics Test Circuits 6 Recommended Circuit Values Around The Triac Load 6 C1 A 6V V Test Procedure I V A V 330 Test Procedure III REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 6 of 7 C0 R0 330 Test Procedure II 6 6V R1 A 6V 330 C1 = 0.1 to 0.47F C0 = 0.1F R0 = 100 R1 = 47 to 100 BCR25RM-12LB Package Dimensions Previous Code TO-3PFM / TO-3PFMV 15.6 0.3 + 0.4 - 0.2 2.0 0.3 2.7 0.3 3.2 Unit: mm 5.5 0.3 3.2 0.3 4.0 0.3 2.6 0.86 1.6 0.86 0.66 5.45 0.5 MASS[Typ.] 5.2g 21.0 0.5 RENESAS Code PRSS0003ZA-A 5.0 0.3 JEITA Package Code SC-93 5.0 0.3 19.9 0.3 Package Name TO-3PFM + 0.2 - 0.1 0.2 0.9 +- 0.1 5.45 0.5 Order Code Lead form Straight type Standard packing Magazine (Tube) Quantity 30 Standard order code Type name Note : Please confirm the specification about the shipping in detail. REJ03G1715-0100 Rev.1.00 Jul 10, 2008 Page 7 of 7 Standard order code example BCR25RM-12LB Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7858/7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2377-3473 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 3518-3399 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 (c) 2008. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.2 To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.