REV. 6/3/05 . [10.79] ~} O1" PANEL GROUNDING TAB 8.082 [1.57] 128 [3.25] 125 [3.18] 4.035 [0.89] (8) Ny $44 \ |_. R50) [21.59] MAX 1X Lo) 0 }-.125 [3.181.010 [0.25] ~| 560 [13.67] MAX ye LJ 040 [1.02] C = 050 [1.27] TYP TOL NON-ACCUM (2) ey 025 [0.64] 100 [2.54] TYP TOL NON-ACCUM 100 [2.54] be Ae 250 [6.35] (2) - [11.43] - *.810 [16.49] 120 [3,05]}-4 L $ _ P.C.B._ RECOMMENDED HOLE LAYOUT SEEN FROM COMPON ENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED DATE REV ECN APF'D. BY 2/2/06 A2 7458 dM NOTES: 1, SONNECTOR MATERIALS: HOUSING: THERMOPLASTIC UL94 V-6 CONTACTS/SHIELD: COPPER ALLOY SHIELD PLATING: NICKEL OR TIN CONTACT PLATING: SELECTIVE GOLD IN CONTACT AREA SEE CHART FOR PART NUMBER 2. FOR PRODUCT SPEGFICATIONS SEE PRO22-i. . TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS. 4. THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE USER THE ABILITY TO HAVE REASONABLE JACK/PANEL CLEARANCES, YET MAINTAIN GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADWSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. a 30 MICRO-INCHES [0.76um] SS7288SFR1A-NF-01 CONTACT PLATING IN MATING AREA PART NUMHER THIRD ANGLE PROJECTION @ = Bel Stewart Connector 11118 Susquehanna Trail South Glen Rock, PA 17327-9199 (717) 235-7512 Fox: (717) 235-7954 _ http: //www.stewartconnector.com DO NOT SCALE DRAWING DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE = EIGHT CONTACT, EIGHT POSTION, SHIELDED FILTER JACK FERRITE INSERT, NONFLANGED, PANEL GROUNDING TAB DIMENSIONS: INCHES [METRIC] | THIS DRAWING AND THE SUBVEGT MATTER SHOWN THEREON | OR BY: KRL DATE > /2 /06 UNLESS OTHERWISE SPEDIFIED ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF TOLERANCES ARE +.005 [0.13] | BEL STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, | APPO BY: WM DATE 9-3-06 ANGLES ARE + 1 COPED, OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN SHEET NO. CONSENT OF BEL STEWART CONNECTOR. THE SUBJECT | DW6 NO. REV. 1 OF 2 MATTER MAY BE PATENTED GR A PATENT MAY BE PENDING. CT720006 A2 { AutoCADREV. 6/3/05 FERRITE MATERIAL CHARACTERISTICS FERRITE NOISE INITIAL VOLUME MA TERIAL SUPPRESSION | PERMEABILITY | RESISTIMTY DESIGNATION RANGE @ B < 10 gauss OHM-CM, 30 MHz 500 FRI 0 0 2708 200 MHz 1500 2 00 wy 180 a 160 ot 1 a 140 HW ING: 120 7 rT OHMS 100 A 4 LLL | aT 80 i LT 4 UY /| 1 60 oP Hr 40 Ut Pa at 20 ArT LT d 1 10 100 1000 30 MICRO-INCHES [0.76um] SS7288SF R1A-NF01 MHz CONTACT PLATING IN MATING AREA PART NUMBER IMPEDANGE CURVE for 7288FR1 INSERT AVERAGE IMPEDANCE CURVE THIRD ANGLE PROJECTION ------. MAX. a MIN. IMPEDANGE CURVES Bel Stewart Connector NOTE E+] eerree MAXIMUM AND MINIMUM IMPEDANCE VALUES ARE DEPENDENT ON: (717) 235-7512 Fax: (717) 235-7954 _ http: //www.stewartconnector.com 1) HOLE POSITION WITHIN THE INSERTS GEOMETRY, AND DO NOT SCALE DRAWNG |TE FIGHT CONTACT, EIGHT POSTION, SHIELDED FILTER JACK 2) FERRITE MATERIAL'S IMPEDANCE VALUE TOLERANCE OF +25% CN Eo me FERRITE INSERT, NONFLANGED, PANEL GROUNDING TAB DIMENSIONS: INCHES [METRIC] | THIS DRAWING AND THE SUBVEGT MATTER SHOWN THEREON | OR BY: KRL DATE > /2 /06 UNLESS OTHERWISE SPECIFIED ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF TOLERANCES ARE +.005 [0.13] | @L STEWART CONNECTOR AND SHALL NOT BE REPRODUCED, | APPD BY: WM GATE 9-3-06 ANGLES ARE + 1 COPED, OR USED IN ANY MANNER WITHOUT PRE WRITTEN TT 2 OF 2 | wreruntarrsorm ner aa racne [1720006 [x2 9 { AutoCAD