MPC9229FA - Freescale Semiconductor / Motorola

MOTOROLA

SEMICONDUCTOR TECHNICAL DATA

Order Number: MPC9229/D

Rev 1 03/2003

Motorola, Inc. 2003

400 MHz Low Voltage PECL

Clock Synthesizer

The MPC9229 is a 3.3V compatible, PLL based clock synthesizer

targeted for high performance clock generation in mid-range to

high-performance telecom, networking and computing applications. With

output frequencies from 25 MHz to 400 MHz and the support of differential

PECL output signals the device meets the needs of the most demanding

clock applications.

Features

•25 MHz to 400 MHz synthesized clock output signal

•Differential PECL output

•LVCMOS compatible control inputs

•On-chip crystal oscillator for reference frequency generation

•3.3V power supply

•Fully integrated PLL

•Minimal frequency overshoot

•Serial 3-wire programming interface

•Parallel programming interface for power-up

•32 lead LQFP and 28 PLCC packaging

•SiGe Technology

•Ambient temperature range 0°Cto+70°C

•Pin and function compatible to the MC12429

Functional Description

The internal crystal oscillator uses the external quartz crystal as the

basis of its frequency reference. The frequency of the internal crystal

oscillator is divided by 16 and then multiplied by the PLL. The VCO within

the PLL operates over a range of 800 to 1600 MHz. Its output is scaled by

a divider that is configured by either the serial or parallel interfaces. The

crystal oscillator frequency fXTAL, the PLL feedback-divider M and the PLL

post-divider N determine the output frequency.

The feedback path of the PLL is internal. The PLL adjusts the VCO output frequency to be 4⋅M times the reference frequency

by adjusting the VCO control voltage. Note that for some values of M (either too high or too low) the PLL will not achieve phase

lock. The PLL will be stable if the VCO frequency is within the specified VCO frequency range (800 to 1600 MHz). The M-value

must be programmed by the serial or parallel interface.

The PLL post-divider N is configured through either the serial or the parallel interfaces, and can provide one of four division

ratios (1, 2, 4, or 8). This divider extends performance of the part while providing a 50% duty cycle. The output driver is driven

differentially from the output divider, and is capable of driving a pair of transmission lines terminated 50Ωto VCC –2.0V.The

positive supply voltage for the internal PLL is separated from the power supply for the core logic and output drivers to minimize

noise induced jitter.

The configuration logic has two sections: serial and parallel. The parallel interface uses the values at the M[8:0] and N[1:0]

inputs to configure the internal counters. It is recommended on system reset to hold the P_LOAD input LOW until power becomes

valid. On the LOW–to–HIGH transition of P_LOAD, the parallel inputs are captured. The parallel interface has priority over the

serial interface. Internal pullup resistors are provided on the M[8:0] and N[1:0] inputs prevent the LVCMOS compatible control

inputs from floating.

The serial interface centers on a fourteen bit shift register. The shift register shifts once per rising edge of the S_CLOCK input.

The serial input S_DATA must meet setup and hold timing as specified in the AC Characteristics section of this document. The

configuration latches will capture the value of the shift register on the HIGH–to–LOW edge of the S_LOAD input. See the

programming section for more information. The TEST output reflects various internal node values, and is controlled by the T[2:0]

bits in the serial data stream. In order to minimize the PLL jitter, it is recommended to avoid active signal on the TEST output.

FA SUFFIX

32 LEAD LQFP PACKAGE

CASE 873A

MPC9229

400 MHZ LOW VOLTAGE

CLOCK SYNTHESIZER

FN SUFFIX

28--LEAD PLCC PACKAGE

CASE 776

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS2

Figure 1. MPC9229 Logic Diagram

GND

TEST

VCC

GND

FOUT

M[3]

M[2]

M[1]

M[0]

P_LOAD

N[1]

N[0]

M[8]

M[7]

M[6]

M[5]

M[4]

S_CLOCK

S_LOAD

VCC_PLL

XTAL_IN

12345678

24 23 22 21 20 19 18 17

Figure 2. MPC9229 28--Lead PLCC Pinout

(Top View)

VCC

XTAL_OUT

XTAL_IN

XTAL_OUT

S_LOAD

÷16

S_DATA

S_CLOCK

M[0:8]

XTAL

PLL

Ref

VCO

800-1600 MHz

÷0to÷511

9-Bit M-Divider

M-Latch N-Latch

10 -- 20 MHz

T-Latch

Te s t

Bit 5-13 Bit 3-4 Bit 0-2

14 Bit Shift Register

Sync

N[1:0]

P/S

÷1

÷2

÷4

÷8

FOUT

TEST

VCC

P_LOAD

÷4

25 24 23 22 21 20 19

11109

Figure 3. MPC9229 32--Lead LQFP Pinout

(Top View)

VCCXTAL_OUT

P_LOAD

M[0]

M[1]

M[2]

M[3]

FOUT

GND

VCC

TEST

GND

S_CLOCK N[1]

N[0]

M[8]

M[7]

M[6]

M[5]

M[4]

S_DATA

S_LOAD

VCC_PLL

XTAL_IN

S_DATA

MPC9229

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

TIMING SOLUTIONS 3 MOTOROLA

Table 1. Pin Configuration

Pin I/O Default Type Function

XTAL_IN, XTAL_OUT Analog Crystal oscillator interface

FOUT, FOUT Output LVPECL Differential clock output

TEST Output LVCMOS Test and device diagnosis output

S_LOAD Input 0LVCMOS Serial configuration control input.

This inputs controls the loading of the configuration latches with the contents of

the shift register. The latches will be transparent when this signal is high, thus the

data must be stable on the high-to-low transition.

P_LOAD Input 1LVCMOS Parallel configuration control input.

This input controls the loading of the configuration latches with the content of the

parallel inputs (M and N). The latches will be transparent when this signal is low,

thus the parallel data must be stable on the low-to-high transition of P_LOAD.

P_LOAD is state sensitive

S_DATA Input 0LVCMOS Serial configuration data input.

S_CLOCK Input 0LVCMOS Serial configuration clock input.

M[0:8] Input 1LVCMOS Parallel configuration for PLL feedback divider (M).

M is sampled on the low-to-high transition of P_LOAD.

N[1:0] Input 1LVCMOS Parallel configuration for Post-PLL divider (N).

N is sampled on the low-to-high transition of P_LOAD

OE Input 1LVCMOS Output enable (active high)

The output enable is synchronous to the output clock to eliminate the possibility of

runt pulses on the FOUT output. OE = L low stops FOUT in the logic low state

(FOUT =L,FOUT=H)

GND Supply Supply Ground Negative power supply (GND)

VCC Supply Supply VCC Positive power supply for I/O and core. All VCC pins must be connected to the

positive power supply for correct operation

VCC_PLL Supply Supply VCC PLL positive power supply (analog power supply)

Table 2. Output frequency range and PLL Post-divider N

1 0 Output division Output frequency range

0 0 1 200 - 400 MHz

0 1 2 100 - 200 MHz

1 0 4 50 - 100 MHz

1 1 8 25 - 50 MHz

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS4

Table 3. General Specifications

Symbol Characteristics Min Typ Max Unit Condition

VTT Output Termination Voltage VCC -2 V

MM ESD protection (Machine Model) 200 V

HBM ESD protection (Human Body Model) 2000 V

LU Latch-Up Immunity 200 mA

CIN Input Capacitance 4.0 pF Inputs

θJA LQFP 32 Thermal resistance junction to ambient

JESD 51-3, single layer test board

JESD 51-6, 2S2P multilayer test board

83.1

73.3

68.9

63.8

57.4

59.0

54.4

52.5

50.4

47.8

86.0

75.4

70.9

65.3

59.6

60.6

55.7

53.8

51.5

48.8

°C/W

Natural convection

100 ft/min

200 ft/min

400 ft/min

800 ft/min

Natural convection

100 ft/min

200 ft/min

400 ft/min

800 ft/min

θJC LQFP 32 Thermal resistance junction to case 23.0 26.3 °C/W MIL-SPEC 883E

Method 1012.1

Table 4. Absolute Maximum Ratingsa

Symbol Characteristics Min Max Unit Condition

VCC Supply Voltage -0.3 3.9 V

VIN DC Input Voltage -0.3 VCC +0.3 V

VOUT DC Output Voltage -0.3 VCC +0.3 V

IIN DC Input Current ±20 mA

IOUT DC Output Current ±50 mA

TSStorage Temperature -65 125 °C

a. Absolute maximum continuous ratings are those maximum values beyond which damage to the device may occur. Exposure to these

conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation at absolute-maximum-rated

conditions is not implied.

Table 5. DC Characteristics (VCC =3.3V ±5%, TA=0°Cto+70°C)

Symbol Characteristics Min Typ Max Unit Condition

LVCMOS control inputs (P_LOAD, S_LOAD, S_DATA, S_CLOCK, M[0:8], N[0:1], OE)

VIH Input High Voltage 2.0 VCC +0.3 VLVCMOS

VIL Input Low Voltage 0.8 VLVCMOS

IIN Input Currenta±200 µA VIN =V

CC or GND

Differential clock output FOUTb

VOH Output High VoltagecVCC--1.02 VCC--0.74 VLVPECL

VOL Output Low VoltagecVCC--1.95 VCC--1.60 VLVPECL

Test and diagnosis output TEST

VOH Output High Voltagec2.0 V IOH =-0.8mA

VOL Output Low Voltagec0.55 V IOL =0.8mA

Supply current

ICC_PLL Maximum PLL Supply Current 20 mA VCC_PLL Pins

ICC Maximum Supply Current 100 mA All VCC Pins

a. Inputs have pull-down resistors affecting the input current.

b. Outputs terminated 50Ωto VTT =V

CC -2V.

c. The MPC9229 TEST output levels are compatible to the MC12429 output levels.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

TIMING SOLUTIONS 5 MOTOROLA

Table 6. AC Characteristics (VCC =3.3V ±5%, TA=0°Cto+70°C)a

Symbol Characteristics Min Typ Max Unit Condition

fXTAL Crystal interface frequency range 10 20 MHz

fVCO VCO frequency rangeb800 1600 MHz

fMAX Output Frequency N = 00 (÷1)

N=01(÷2)

N=10(÷4)

N=11(÷8)

200

100

400

200

100

MHz

DC Output duty cycle 45 50 55 %

tr,t

fOutput Rise/Fall Time 0.05 0.3 ns 20% to 80%

fS_CLOCK Serial interface programming clock frequencyc010 MHz

tP, MI N Minimum pulse width (S_LOAD, P_LOAD)50 ns

tSSetup Time S_DATA to S_CLOCK

S_CLOCK to S_LOAD

M, N to P_LOAD

tSHold Time S_DATA to S_CLOCK

M, N to P_LOAD

tJIT(CC) Cycle--to--cycle jitter N = 00 (÷1)

N=01(÷2)

N=10(÷4)

N=11(÷8)

130

160

190

tJIT(PER) Period Jitter N = 00 (÷1)

N=01(÷2)

N=10(÷4)

N=11(÷8)

120

140

170

tLOCK Maximum PLL Lock Time 10 ms

a. AC characteristics apply for parallel output termination of 50Ωto VTT.

b. The input frequency fXTAL and the PLL feedback divider M must match the VCO frequency range: fVCO =f

XTAL ⋅M÷4.

c. The frequency of S_CLOCK is limited to 10 MHz in serial programming mode. S_CLOCK can be switched at higher frequencies when used

as test clock in test mode 6. See application section for more details.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS6

Programming the MPC9229

Programming the MPC9229 amounts to properly

configuring the internal PLL dividers to produce the desired

synthesized frequency at the output. The output frequency

can be represented by this formula:

fOUT =(f

XTAL ÷16) ⋅(4 ⋅M) ÷(4 ⋅N) or (1)

fOUT =(f

XTAL ÷16) ⋅M÷N(2)

where fXTAL is the crystal frequency, M is the PLL

feedback-divider and N is the PLL post-divider. The input

frequency and the selection of the feedback divider M is limited

by the VCO-frequency range. fXTAL and M must be configured

to match the VCO frequency range of 800 to 1600 MHz in

order to achieve stable PLL operation:

MMIN =4⋅fVCO,MIN ÷fXTAL and (3)

MMAX =4⋅fVCO,MAX ÷fXTAL (4)

For instance, the use of a 16 MHz input frequency requires

the configuration of the PLL feedback divider between M=200

and M = 400. Table 7 shows the usable VCO frequency and

M divider range for other example input frequencies.

Assuming that a 16 MHz input frequency is used, equation (2)

reduces to:

fOUT =M÷N(5)

Table 7. MPC9229 Frequency Operating Range

VCO frequency for an crystal interface frequency of Output frequency for fXTAL=16 MHz and for N =

MM[8:0] 10 12 14 16 18 20 1 2 4 16

160 010100000 800

170 010101010 850

180 010110100 810 900

190 010111110 855 950

200 011001000 800 900 1000 200 100 50 25

210 011010010 840 945 1050 210 105 52.5 26.25

220 011011100 880 990 1100 220 110 55 27.50

230 011100110 805 920 1035 1150 230 115 57.5 28.75

240 011110000 840 960 1080 1200 240 120 60 30

250 011111010 875 100 1125 1250 250 125 62.5 31.25

260 100000100 910 1040 1170 1300 260 130 65 32.50

270 100001110 810 945 1080 1215 1350 270 135 67.5 33.75

280 100011000 840 980 1120 1260 1400 280 140 70 35

290 100100010 870 1015 1160 1305 1450 290 145 72.5 36.25

300 100101100 900 1050 1200 1350 1500 300 150 75 37.5

310 100110110 930 1085 1240 1395 1550 310 155 77.5 38.75

320 101000000 800 960 1120 1280 1440 1600 320 160 80 40

330 101001010 825 990 1155 1320 1485 330 165 82.5 41.25

340 101010100 850 1020 1190 1360 1530 340 170 85 42.5

350 101011110 875 1050 1225 1400 1575 350 175 87.5 43.75

360 101101000 900 1080 1260 1440 360 180 90 45

370 101110010 925 1110 1295 1480 370 185 92.5 46.25

380 101111100 950 1140 1330 1520 380 190 95 47.5

390 110000110 975 1170 1365 1560 390 195 97.5 48.75

400 110010000 1000 1200 1400 1600 400 200 100 50

410 110011010 1025 1230 1435

420 110100100 1050 1260 1470

430 110101110 1075 1290 1505

440 110111000 1100 1320 1540

450 111000010 1125 1350 1575

510 111111110 1275 1530

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

TIMING SOLUTIONS 7 MOTOROLA

Substituting N for the four available values for N (1, 2, 4, 8)

yields:

Table 8. Output Frequency Range for fXTAL =16MHz

NFOUT FOUT range FOUT step

1 0 Value

0 0 1 M 200 - 400 MHz 1MHz

0 1 2 M÷2100 - 200 MHz 500 kHz

1 0 4 M÷450 - 100 MHz 250 kHz

1 1 8 M÷825 - 50 MHz 125 kHz

Example frequency calculation for an 16 MHz input

frequency

If an output frequency of 131 MHz was desired the following

steps would be taken to identify the appropriate M and N

values. According to Table 8, 131 MHz falls in the frequency

set by an value of 2 so N[1:0] = 01. For N = 2 the output

frequency is FOUT =M÷2 and M = FOUT x 2. Therefore M =

2 x 131 = 262, so M[8:0] = 100000110. Following this

procedure a user can generate any whole frequency between

25 MHz and 400 MHz. Note than for N > 2 fractional values of

can be realized. The size of the programmable frequency

steps (and thus the indicator of the fractional output

frequencies achievable) will be equal to:

fSTEP =f

XTAL ÷16 ÷N(6)

Using the parallel and serial interface

The M and N counters can be loaded either through a

parallel or serial interface. The parallel interface is controlled

via the P_LOAD signal such that a LOW to HIGH transition will

latch the information present on the M[8:0] and N[1:0] inputs

into the M and N counters. When the P_LOAD signal is LOW

the input latches will be transparent and any changes on the

M[8:0] and N[1:0] inputs will affect the FOUT output pair. To

use the serial port the S_CLOCK signal samples the

information on the S_DATA line and loads it into a 14 bit shift

serial load operation to function. The Test register is loaded

with the first three bits, the N register with the next two and the

M register with the final eight bits of the data stream on the

S_DATA input. For each register the most significant bit is

loaded first (T2, N1 and M8). A pulse on the S_LOAD pin after

the shift register is fully loaded will transfer the divide values

into the counters. The HIGH to LOW transition on the S_LOAD

input will latch the new divide values into the counters. Figure

4 illustrates the timing diagram for both a parallel and a serial

load of the MPC9229 synthesizer. M[8:0] and N[1:0] are

normally specified once at power–up through the parallel

interface, and then possibly again through the serial interface.

This approach allows the application to come up at one

frequency and then change or fine–tune the clock as the ability

to control the serial interface becomes available.

Using the test and diagnosis output TEST

The TEST output provides visibility for one of the several

internal nodes as determined by the T[2:0] bits in the serial

configuration stream. It is not configurable through the parallel

interface. Although it is possible to select the node that

represents FOUT

, the CMOS output is not able to toggle fast

enough for higher output frequencies and should only be used

for test and diagnosis. The T2, T1 and T0 control bits are

preset to ‘000’ when P_LOAD is LOW so that the PECL FOUT

outputs are as jitter–free as possible. Any active signal on the

TEST output pin will have detrimental affects on the jitter of the

PECL output pair. In normal operations, jitter specifications are

only guaranteed if the TEST output is static. The serial

configuration port can be used to select one of the alternate

functions for this pin. Mostof the signals available on the TEST

output pin are useful only for performance verification of the

MPC9229 itself. However the PLL bypass mode may be of

interest at the board level for functional debug. When T[2:0] is

set to 110 the MPC9229 is placed in PLL bypass mode. In this

mode the S_CLOCK input is fed directly into the M and N

dividers. The N divider drives the FOUT differential pair and the

M counter drives the TEST output pin. In this mode the

S_CLOCK input could be used for low speed board level

functional test or debug. Bypassing the PLL and driving FOUT

directly gives the user more control on the test clocks sent

through the clock tree. Figure 6 shows the functional setup of

the PLL bypass mode. Because the S_CLOCK is a CMOS

level the input frequency is limited to 200 MHz. This means the

fastest the FOUT pin can be toggled via the S_CLOCK is 100

MHz as the divide ratio of the Post-PLL divider is 2 (if N = 1).

Note that the M counter output on the TEST output will not be

a 50% duty cycle.

Table 9. Test and Debug Configuration for TEST

T[2:0] TEST output

T2 T1 T0

0 0 0 14-bit shift register outa

0 0 1 Logic 1

0 1 0 fXTAL ÷16

0 1 1 M-Counter out

1 0 0 FOUT

1 0 1 Logic 0

1 1 0 M-Counter out in PLL-bypass mode

1 1 1 FOUT ÷4

a. Clocked out at the rate of S_CLOCK

Table 10. Debug Configuration for PLL bypassa

Output Configuration

FOUT S_CLOCK ÷N

TEST M-Counter outb

a. T[2:0]=110. AC specifications do not apply in PLL bypass

mode

b. clocked out at the rate of S_CLOCK÷(4⋅N)

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS8

Figure 4. Serial Interface Timing Diagram

S_CLOCK

S_DATA

S_LOAD

M[8:0]

N[1:0]

P_LOAD

T2 T1 T0 N1 N0 M8 M7 M6 M5 M4 M3 M2 M1 M0

M, N

First

Bit

Last

Bit

Power Supply Filtering

The MPC9229 is a mixed analog/digital product. Its analog

circuitry is naturally susceptible to random noise, especially if

this noise is seen on the power supply pins. Random noise on

the VCC_PLL pin impacts the device characteristics. The

MPC9229 provides separate power supplies for the digital

circuitry (VCC) and the internal PLL (VCC_PLL) of the device.

The purpose of this design technique is to try and isolate the

high switching noise digital outputs from the relatively

sensitive internal analog phase–locked loop. In a controlled

environment such as an evaluation board, this level of

isolation is sufficient. However, in a digital system environment

where it is more difficult to minimize noise on the power

supplies a second level of isolation may be required. The

simplest form of isolation is a power supply filter on the

VCC_PLL pin for the MPC9229. Figure 5 illustrates a typical

power supply filter scheme. The MPC9229 is mostsusceptible

to noise with spectral content in the 1 kHz to 1 MHz range.

Therefore, the filter should be designed to target this range.

The key parameter that needs to be met in the final filter design

is the DC voltage drop that will be seen between the VCC

supply and the MPC9229 pin of the MPC9229. From the data

sheet, the VCC_PLL current (the current sourced through the

VCC_PLL pin) is maximum 20 mA, assuming that a minimum

of 2.835 V must be maintained on the VCC_PLL pin. The

resistor shown in Figure 5 must have a resistance of 10-15 Ω

to meet the voltage drop criteria. The RC filter pictured will

provide a broadband filter with approximately 100:1

attenuation for noise whose spectral content is above 20 kHz.

As the noise frequency crosses the series resonant point of an

individual capacitor its overall impedance begins to look

inductive and thus increases with increasing frequency. The

parallel capacitor combination shown ensures that a low

impedance path to ground exists for frequencies well above

the bandwidth of the PLL. Generally, the resistor/capacitor

filter will be cheaper, easier to implement and provide an

adequate level of supply filtering. A higher level of attenuation

can be achieved by replacing the resistor with an appropriate

valued inductor. A 1000 µH choke will show a significant

impedance at 10 kHz frequencies and above. Because of the

current draw and the voltage that must be maintained on the

VCC_PLL pin, a low DC resistance inductor is required (less

than 15 Ω).

Figure 5. VCC PLL Power Supply Filter

VCC_PLL

VCC

MPC9229

C1,C

2= 0.01...0.1 µF

VCC

CF=22µF

RF=10--15Ω

Layout Recommendations

The MPC9229 provides sub–nanosecond output edge

rates and thus a good power supply bypassing scheme is a

must. Figure 6 shows a representative board layout for the

MPC9229. There exists many different potential board layouts

and the one pictured is but one. The important aspect of the

layout in Figure 6 is the low impedance connections between

VCC and GND for the bypass capacitors. Combining good

quality general purpose chip capacitors with good PCB layout

techniques will produce effective capacitor resonances at

frequencies adequate to supply the instantaneous switching

current for the MPC9229 outputs. It is imperative that low

inductance chip capacitors are used; it is equally important

that the board layout does not introduce back all of the

inductance saved by using the leadless capacitors. Thin

interconnect traces between the capacitor and the power

plane should be avoided and multiple large vias should be

used to tie the capacitors to the buried power planes. Fat

interconnect and large vias will help to minimize layout

induced inductance and thus maximize the series resonant

point of the bypass capacitors. Note the dotted lines circling

the crystal oscillator connection to the device. The oscillator is

a series resonant circuit and the voltage amplitude across the

crystal is relatively small. It is imperative that no actively

switching signals cross under the crystal as crosstalk energy

coupled to these lines could significantly impact the jitter of the

device. Special attention should be paid to the layout of the

crystal to ensure a stable, jitter free interface between the

crystal and the on–board oscillator. Although the MPC9229

has several design features to minimize the susceptibility to

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

TIMING SOLUTIONS 9 MOTOROLA

power supply noise (isolated power and grounds and fully

differential PLL), there still may be applications in whichoverall

performance is being degraded due to system power supply

noise. The power supply filter and bypass schemes discussed

in this section should be adequate to eliminate power supply

noise related problems in most designs.

Figure 6. PCB Board Layout Recommendation for

the PLCC28 Package

Xtal

C1 C1

=GND

=Via

Using the On--Board Crystal Oscillator

The MPC9229 features a fully integrated on--board crystal

oscillator to minimize system implementation costs. The

oscillator is a series resonant, multivibrator type design as

opposed to the more common parallel resonant oscillator

design. The series resonant design provides better stability

and eliminates the need for large on chip capacitors. The

oscillator is totally self contained so that the only external

component required is the crystal. As the oscillator is

somewhat sensitive to loading on its inputs the user is advised

to mount the crystal as close to the MPC9229 as possible to

avoid any board level parasitics. To facilitate co--location

surface mount crystals are recommended, but not required.

Because the series resonant design is affected by capacitive

loading on the xtal terminals loading variation introduced by

crystals from different vendors could be a potential issue. For

crystals with a higher shunt capacitance it may be required to

place a resistance across the terminals to suppress the third

harmonic. Although typically not required it is a good idea to

layout the PCB with the provision of adding this external

resistor. The resistor value will typically be between 500 and

1KΩ.

The oscillator circuit is a series resonant circuit and thus for

optimum performance a series resonant crystal should be

used. Unfortunately most crystals are characterized in a

parallel resonant mode. Fortunately there is no physical

difference between a series resonant and a parallel resonant

crystal. The difference is purely in the way the devices are

characterized. As a result a parallel resonant crystal can be

used with the MPC9229 with only a minor error in the desired

frequency. A parallel resonant mode crystal used in a series

resonant circuit will exhibit a frequency of oscillation a few

hundred ppm lower than specified, a few hundred ppm

translates to kHz inaccuracies. In a general computer

application this level of inaccuracy is immaterial. Table 11

below specifies the performance requirements of the crystals

to be used with the MPC9229.

Table 11. Recommended Crystal Specifications

Parameter Value

Crystal Cut Fundamental AT Cut

Resonance Series Resonance*

Frequency Tolerance ±75ppm at 25°C

Frequency/Temperature Stability ±150pm 0 to 70°C

Operating Range 0to70°C

Shunt Capacitance 5--7pF

Equivalent Series Resistance (ESR) 50 to 80Ω

Correlation Drive Level 100µW

Aging 5ppm/Yr (First 3 Years)

* See accompanying text for series versus parallel resonant

discussion.

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS10

OUTLINE DIMENSIONS

FN SUFFIX

PLASTIC PLCC PACKAGE

CASE 776--02

ISSUE D

NOTES:

1. DATUMS --L--, --M--, AND --N-- DETERMINED

WHERE TOP OF LEAD SHOULDER EXITS

PLASTIC BODY AT MOLD PARTING LINE.

2. DIMENSION G1, TRUE POSITION TO BE

MEASURED AT DATUM --T--, SEATING PLANE.

3. DIMENSIONS R AND U DO NOT INCLUDE

MOLD FLASH. ALLOWABLE MOLD FLASH IS

0.010 (0.250) PER SIDE.

4. DIMENSIONING AND TOLERANCING PER

ANSI Y14.5M, 1982.

5. CONTROLLING DIMENSION: INCH.

6.THEPACKAGETOPMAYBESMALLERTHAN

THEPACKAGEBOTTOMBYUPTO0.012

(0.300). DIMENSIONS R AND U ARE

DETERMINED AT THE OUTERMOST

EXTREMES OF THE PLASTIC BODY

EXCLUSIVE OF MOLD FLASH, TIE BAR

BURRS, GATE BURRS AND INTERLEAD

FLASH, BUT INCLUDING ANY MISMATCH

BETWEEN THE TOP AND BOTTOM OF THE

PLASTIC BODY.

7. DIMENSION H DOES NOT INCLUDE DAMBAR

PROTRUSION OR INTRUSION. THE DAMBAR

PROTRUSION(S) SHALL NOT CAUSE THE H

DIMENSION TO BE GREATER THAN 0.037

(0.940). THE DAMBAR INTRUSION(S) SHALL

NOT CAUSE THE H DIMENSION TO BE

SMALLER THAN 0.025 (0.635).

-- N --

-- M --

-- L --

Y BRK

28 1

VIEW S

L--M

0.010 (0.250) N S

L--M

0.007 (0.180) N S

0.004 (0.100)

SEATING

PLANE

L--M

0.007 (0.180) N S

-- T --

L--M

0.010 (0.250) N S

L--M

0.007 (0.180) N S

L--M

0.007 (0.180) N S

G1X

VIEW D--D

L--M

0.007 (0.180) N S

VIEW S

L--M

0.007 (0.180) N S

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

A0.485 0.495 12.32 12.57

B0.485 0.495 12.32 12.57

C0.165 0.180 4.20 4.57

E0.090 0.110 2.29 2.79

F0.013 0.019 0.33 0.48

G0.050 BSC 1.27 BSC

H0.026 0.032 0.66 0.81

J0 . 0 2 0 -- -- -- 0 . 5 1 -- -- --

K0 . 0 2 5 -- -- -- 0 . 6 4 -- -- --

R0.450 0.456 11.43 11.58

U0.450 0.456 11.43 11.58

V0.042 0.048 1.07 1.21

W0.042 0.048 1.07 1.21

X0.042 0.056 1.07 1.42

Y-- -- -- 0 . 0 2 0 -- -- -- 0 . 5 0

Z210 210

G1 0.410 0.430 10.42 10.92

K1 0 . 0 4 0 -- -- -- 1 . 0 2 -- -- --

__ __

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

TIMING SOLUTIONS 11 MOTOROLA

OUTLINE DIMENSIONS

FA SUFFIX

LQFP PACKAGE

CASE 873A-03

ISSUE B

12 REF

D/2

EE1

e/2

DETAIL G

BASE

c1c

METAL

SECTION F--F

SEATING

PLANE

RR2

(S) L

(L1)

0.25

GAUGE PLANE

DETAIL AD

D1/2

E1/2

E/2

A--B0.20 H

0.1 C

(1)

A, B, D

A--B

0.20 DC

NOTES:

1. DIMENSIONS ARE IN MILLIMETERS.

2. INTERPRET DIMENSIONS AND TOLERANCES PER

ASME Y14.5M, 1994.

3. DATUMS A, B, AND D TO BE DETERMINED AT

DATUM PLANE H.

4. DIMENSIONS D AND E TO BE DETERMINED AT

SEATING PLANE C.

5. DIMENSION b DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR PROTRUSION

SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED

THEMAXIMUMbDIMENSIONBYMORETHAN

0.08--mm. DAMBAR CANNOT BE LOCATED ON THE

LOWER RADIUS OR THE FOOT. MINIMUM SPACE

BETWEEN PROTRUSION AND ADJACENT LEAD OR

PROTRUSION: 0.07--mm.

6. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD

PROTRUSION. ALLOWABLE PROTRUSION IS

0.25--mm PER SIDE. D1 AND E1 ARE MAXIMUM

PLASTIC BODY SIZE DIMENSIONS INCLUDING

MOLD MISMATCH.

7. EXACT SHAPE OF EACH CORNER IS OPTIONAL.

8. THESE DIMENSIONS APPLY TO THE FLAT

SECTION OF THE LEAD BETWEEN 0.1--mm AND

0.25--mm FROM THE LEAD TIP.

DIM MIN MAX

MILLIMETERS

7.00 BSC

0.80 BSC

9.00 BSC

b1 0.30 0.40

c0.09 0.20

c1 0.09 0.16

L1 1.00 REF

R1 0.08 0.20

1.40 1.60

0.05 0.15

1.35 1.45

0.30 0.45

0 . 0 8 -- -- --

9.00 BSC

7.00 BSC

0.50 0.70

0.20 REF

A--B0.20 C D

6 4

DETAIL G

PIN 1 INDEX

32X

28X

5 8

PLATING

RR1

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...

MPC9229

MOTOROLA TIMING SOLUTIONS12

Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright

licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document.

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and

specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola

data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”

must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of

others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other

applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury

or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and holdMotorola

and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees

arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that

Motorola was negligent regarding the design or manufacture of the part.

MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office. All other product or service names are the property of their respective

owners.

EMotorola Inc. 2003

HOW TO REACH US:

USA/EUROPE/LOCATIONS NOT LISTED:ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre,

2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.

TECHNICAL INFORMATION CENTER: 852--26668334

1--800--521--6274 or 480--768--2130

HOME PAGE: http://motorola.com/semiconductors

JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center,

3--20--1, Minami--Azabu, Minato--ku, Tokyo 106--8573 Japan

81--3--3440--3569

MPC9229/D

◊

Freescale Semiconductor, I

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

nc...