ACT520/ACT520A Rev 0, 05-Jun-15 ActiveQRTM Quasi-Resonant PWM Controller conventional solutions and exceeds the latest ES2.0 efficiency standard with good margin. FEATURES * DCM and Quasi-Resonant Operation ACT520/ACT520A integrates comprehensive protection. In case of over temperature, over voltage, short winding, short current sense resistor, open loop an d overload conditions, it would enter into auto restart mode including Cycle-by-Cycle current limiting. * High VDD Sustain Voltage for Wide Output Range Application such as QC2.0 * Primary Side Constant Current Control * Integrated Patented Frequency Foldback Technique ACT520/ACT520A is to achieve no overshoot and very short rise time even with big capacitive load with the built-in fast and soft start process. * Integrated Patented Line Compensation * Built-in Soft-Start Circuit * Line Under-Voltage, Thermal, Output Over- In low line full load condition, ACT520/ACT520A is able to be designed to work in first valley turn on DCM mode to meet different types of applications. Quasi-Resonant (QR) operation mode can effectively improve efficiency during DCM operation, and reduce the EMI noise and further reduce the components in input filter. voltage, Output Short Protections * * * * Current Sense Resistor Short Protection Transformer Short Winding Protection 30mW Standby Power Complies with Global Energy Efficiency and CEC Average Efficiency Standards ACT520/ACT520A uses an opto-coupler feedback architecture to provide accurate constant voltage even at low loads, constant current (CV/CC) regulation. Integrated line and primary inductance compensation circuitry provides accurate constant current operation despite wide variations in line voltage and primary inductance. * Sop-8 Packages APPLICATIONS * AC/DC Adaptors/Chargers for Cell Phones, Cordless Phone, PDAs, E-books ACT520 is idea for QC2.0 adaptor application up to 30 Watt. * Adaptors for Portable Media Player, DSCs, Set-top boxes, DVD players, records ACT520A is typical for low standby power (<20mW) 12W charger application. * Linear Adapter Replacements Figure 1: Simplified Application Circuit GENERAL DESCRIPTION The ACT520/ACT520A is a high performance peak current mode PWM controller. ACT520/ACT520A applies ActiveQRTM and frequency foldback technique to reduce EMI and improve efficiency. ACT520/ACT520A's maximum design switching frequency is set at 130kHz. Very low standby power, good dynamic response and accurate voltage regulation is achieved with an opto-coupler and the secondary side control circuit. The idle mode operation enables low standby power of 30mW with small output voltage ripple. By applying frequency foldback and ActiveQRTM technology, ACT520/ACT520A increases the average system efficiency compared to Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -1- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 ORDERING INFORMATION PART NUMBER TEMPERATURE RANGE PACKAGE PINS PACKING METHOD ACT520SH-T -40C to 85C SOP-8 8 TUBE & REEL ACT520SH ACT520ASH-T -40C to 85C SOP-8 8 TUBE & REEL ACT520ASH TOP MARK PIN CONFIGURATION SOP-8 ACT520SH SOP-8 ACT520ASH PIN DESCRIPTIONS PIN NAME DESCRIPTION 1 EN 2 GATE Gate Drive. Gate driver for the external MOSFET transistor. 3 GND Ground. 4 CS Current Sense Pin. Connect an external resistor (RCS) between this pin and ground to set peak current limit for the primary switch. 5 FB Feedback Pin. Connect this pin to optocouplers's collector for output regulation. 6 VDET 7 RT 8 VDD Connect this to the gate of the N-depletion FET. Valley Detector Pin. Connect this pin to a resistor divider network from the auxiliary winding to detect zero-crossing points for valley turn on operation. Connected through a NTC resistor to ground for adjustable OTP, or empty if not used. Power Supply. This pin provides bias power for the IC during startup and steady state operation. Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -2- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 ABSOLUTE MAXIMUM RATINGSc PARAMETER VALUE UNIT FB, CS, VDET to GND -0.3 to + 6 V VDD, GATE to GND -0.3 to + 45 V 0.625 W 100 mA -40 to 150 C 160 C/W -55 to 150 C 300 C Maximum Power Dissipation (SOP-8) Maximum Continuous VDD Current Operating Junction Temperature Junction to Ambient Thermal Resistance (JA) Storage Temperature Lead Temperature (Soldering, 10 sec) c: Do not exceed these limits to prevent damage to the device. Exposure to absolute maximum rating conditions for long periods. ELECTRICAL CHARACTERISTICS (VDD = 33V, LM = 0.27mH, RCS = 0.806, VOUT = 12V, NP = 34, NS =6, NA =16, TA = 25C, unless otherwise specified.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Supply VDD Turn-On Voltage VDDON VDD Rising from 0V 16 18 20 V VDD Turn-Off Voltage VDDOFF VDD Falling after Turn-on 6.5 7.0 7.5 V VDD Over Voltage Protection VDDOVP VDD Rising from 0V 43 44 45 V 10 A Start Up Supply Current IDDST IDD Supply Current IDD VDD=16V, before VDD Turn-on (with N-depletion FET) VDD = 18V, after VDD Turn-on ,FB floating 0.5 0.8 mA 0.3 mA IDD Supply Current at Standby IDDSTBY FB = 1.9V 0.2 IDD Supply Current at Fault IDDFAULT Fault mode, FB Floating 250 A Feedback FB Pull up Resistor RFB 15 k CS to FB Gain ACS 2 V/V VFB at Max Peak Current VFBPEAK 3 + VBE V FB Threshold to Stop Switching VFBBM1 1.9 V FB Threshold to Start Switching VFBBM2 1.95 V Output Overload Threshold VFBOLP 3.75 V TOVBLANK 400 ms Slope 24 mV/S RT Source Current IOTP 20 A Trigger Voltage for OTP VOTP 1.25 V OverLoad/Over Voltage Blanking Time Slope Compensation RT Section Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -3- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 ELECTRICAL CHARACTERISTICS CONT'D (VDD = 33V, LM = 0.27mH, RCS = 0.806, VOUT = 12V, NP = 34, NS =6, NA =16, TA = 25C, unless otherwise specified.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT VCSLIM 0.98 1 1.02 V TCSBLANK 240 300 360 ns Current Limit CS Current Limit Threshold Leading Edge Blanking Time GATE DRIVE Gate High Level current source IOG_ON VGATE = 5V 30 Gate Rise Time TRISE VDD = 10V, CL = 1nF 250 350 ns Gate Falling Time TFALL VDD = 10V, CL = 1nF 50 100 ns Gate Low Level ON-Resistance RONLO ISINK = 30mA 20 Gate High Level ON-Resistance RONHI ISOURCE = 30mA 40 Gate Voltage VGATE VDD = 10V, CL = 1nF 11 V Max Gate Voltage VG.MAX VDD = 45V, Switching 14 V GATE = 25V, before VDD turn-on 1 A Gate Leakage Current mA Oscillator Maximum Switching Frequency fMAX Switching Frequency Foldback fMIN ACT520 130 ACT520A 90 fMAX/3 kHz 75 % 100 mV 2.5 s 1 A CS Short Waiting Time 2.5 s CS Short Detection Threshold 0.1 CS Open Threshold Voltage 2.5 V Abnormal OCP Blanking Time 150 ns Maximum Duty Cycle FB = 2.3V+VBE kHz DMAX 65 Valley Detection ZCD Threshold Voltage VDETTH No valley detected, force turn-on main switch Valley Detection Time Window VDET Leakage Current Protection 0.15 V Line UVLO IVDETUVLO 60 A Line OVP IVDETOVP 2.4 mA VDET Over Voltage Protection VDETVOOVP 2.75 V VDET Vo Short Threshold VDETVOshort 0.58 V Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -4- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 FUNCTIONAL BLOCK DIAGRAM Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -5- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 FUNCTIONAL DESCRIPTION ACT520/ACT520A is a high performance peak current mode low-voltage PWM controller IC. The controller includes the most advance features that are required in the adaptor applications up to 30 Watt. Unique fast startup, frequency foldback, QR switching technique, accurate peak current line compensation, idle mode, short winding protection, OCP, OTP, OVP and UVLO are included in the controller. ACT520/ACT520A enters current limit condition and causes the secondary output voltage to drop. As the output voltage decreases, so does the flyback voltage in a proportional manner. An internal current shaping circuitry adjusts the switching frequency based on the flyback voltage so that the transferred power remains proportional to the output voltage, resulting in a constant secondary side output current profile. The energy transferred to the output during each switching cycle is 1/2(LP x ILIM^2) x , where LP is the transformer primary inductance, ILIM is the primary peak current, and is the conversion efficiency. From this formula, the constant output current can be derived: Startup VDD is the power supply terminal for the ACT520/ ACT520A. During startup, the N-depletion FET will be turned ON. Once VDD reaches VDDON voltage, the ACT520/ACT520A will start switching and the N -depletion FET is turned OFF. To startup with a big capacitive load, a fast startup sequence is implemented in ACT520/ACT520A. To eliminate the initial current stress on the MOSFET, a soft startup sequence is implemented in ACT520/ACT520A. During startup period, the IC begins to operate with minimum Ippk to minimize the switching stresses for the main switch, output diode and transformers. And then, the IC operates at maximum power output to achieve fast rise time. After this, VOUT reaches about 90% VOUT , the IC operates with a `soft-landing' mode(decrease Ippk) to avoid output overshoot. IOUTCC = No Load Idle Mode In no load standby mode, the feedback voltage falls and reaches VFBBM1, below VFBBM2 ACT520/ACT520A stop switching. After it stops, as a result of a feedback reaction, the feedback voltage increases. When the feedback voltage reaches VFBBM2, ACT520/ACT520A start switching again. Feedback voltage drops again and output voltage starts to bounds back and forward with very small output ripple. ACT520/ACT520A leaves idle mode when load is added strong enough to pull feedback voltage exceed VFBBM2. In constant voltage operation, the ACT520/ACT520A regulates its output voltage through secondary side control circuit . The output voltage information is sensed at FB pin through OPTO coupling. The error signal at FB pin is amplified through TL431 and OPTO circuit. When the secondary output voltage is above regulation, the error amplifier output voltage decreases to reduce the switch current. When the secondary output voltage is below regulation, the error amplifier output voltage increases to ramp up the switch current to bring the secondary output back to regulation. The output regulation voltage is determined by the following relationship: RF1 ) RF 2 (2) where fSW is the switching frequency and VOUTCV is the nominal secondary output voltage. There is an external resistor, Rline, connected in series between CS pin and RCS. This resistor is used to compensate for the line voltage. Constant Voltage (CV) Mode Operation VOUTCV = VREF _ TL 431 x (1 + x fSW 1 V x Lp x ( CS )2 x ( ) 2 RCS VOUTCV Figure 2: Idle Mode Vo 12V Io 2A 0A Vfb (1) Vfb_olp Vfb_fl Vfbbm2 Vfbbm1 where RF1 (R15) and RF2 (R16) are top and bottom feedback resistor of the TL431. Ip Ilim Ip_FL t Constant Current (CC) Mode Operation When the secondary output current reaches a level set by the internal current limiting circuit, the Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -6- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 FUNCTIONAL DESCRIPTION CONT'D Primary Inductor Current Limit Compensation Auto-Restart Operation ACT520/ACT520A will enter into auto-restart mode when a fault is identified. There is a startup phase in the auto-restart mode. After this startup phase the conditions are checked whether the failure is still present. Normal operation proceeds once the failure mode is removed. Otherwise, new startup phase will be initiated again. The ACT520/ACT520A integrates a primary inductor peak current limit compensation circuit to achieve constant current over wide line and wide inductance. Frequency Foldback To reduce the power loss during fault mode, the startup delay control is implemented. The startup delay time increases over lines. When the load drops to 75% of full load level, ACT520/ACT520A starts to reduce the switching frequency, which is proportional to the load current ,to improve the efficiency of the converter. ACT520/ACT520A's load adaptive switching frequency enables applications to meet all latest green energy standards. The actual minimum average switching frequency is programmable with output capacitance, feedback circuit and dummy load (while still meeting standby power). Valley Switching PROTECTION FUNCTIONS FAILURE CONDITION PROTECTION MODE VDD Over Voltage VDD > 44V (4 duty cycle) Auto Restart VVDET Over Voltage/No Voltage VVD > 2.75V or No switching for 4 cycles Auto Restart Over Temperature ACT520/ACT520A employed valley switching from no load to heavy load to reduce switching loss and EMI. In discontinuous mode operation, the resonant voltage between inductance and parasitic capacitance on MOSFET source pin is coupled by auxiliary winding and reflected on VDET pin through feedback network R5, R6. Internally, the VDET pin is connected to an zero-crossing detector to generate the switch turn on signal when the conditions are meet. Short Winding/ Short Diode Figure 3: Valley Switching VOTP < 1.25V VCS > 1.75V Auto Restart Auto Restart Over Load/Open Loop ( No CC) IPK = ILIMIT or VFB = 4V for 400ms Auto Restart Output Short Circuit VDET < 0.58V Auto Restart VDD Under Voltage VDD < 7V Auto Restart Line Brown Out IVDETUVLO < 60A Auto Restart V Vdrain_gnd DC voltage Possible Valley turn on Ton t T Protection Features The ACT520/ACT520A provides full protection functions. The following table summarizes all protection functions. Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -7- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 TYPICAL APPLICATION Design Example 15F electrolytic capacitors. The design example below gives the procedure for rapid charger flyback converter using ACT520. Refer to application circuit Figure 4, the design for a QC2.0 application starts with the following specification: The maximum duty cycle is set to be 44% at low line voltage 90VAC and the circuit efficiency is estimated to be 83%. Then the maximum average input current is: Input Voltage Range 90VAC - 265VAC, 50/60Hz Output Power, PO 18W Output Voltage, VOUTCV 12/9/5V Full Load Current, IOUTFL 1.5A Constant Current, IOUTCC 1.5-1.9A System Efficiency CV, 0.83 V INDC = _ MIN 2V ) DC = 2 x V IN ( MAX ) AC Lp = 2 x LI N 2 x 271 = = 1 .23 A DMAX 0 .44 (6) V INDC _ MIN D max I LIM x f s (7) The maximum primary turns on time: TON _ MAX = Lp = ILIM VINDC _ MIN (8) 0.27 mH x 1.23 A = 4.15 s 80 The ringing periods from primary inductance with mosfet Drain-Source capacitor: TRINGING_ MAX = 2 Lp _ MAXCDS _ MAX = 2 x 3.14 x 0.27 mH x (1 + 7%) x100PF = 1.06s (9) Design only an half ringing cycle at maximum load in minimum low line, so secondly reset time: TRST = TSW - TON _ MAX - 0 .5TRINGING _ MAX = 1 / 110 kHz - 4 .15 s - 0 .5 x 1 .06 s = 4 .41 s (10) Base on conservation of energy and transformer transform identity, the primary to secondary turns ratio NP/NS: (3) N N P S = T ON T RST x V IN _ MIN V OUT 4 . 15 80 = x 4 . 41 12 + 0 . 35 (4) + VD (11) = 6 .1 The auxiliary to secondary turns ratio NA/NS: NA VDD + VD' 32 + 0.45 = = = 2.63 NS VOUT + VD 12 + 0.35 Where is the estimated circuit efficiency, fL is the line frequency, tC is the estimated rectifier conduction time, CIN is empirically selected to two ActiveQRTM is a trademark of Active-Semi. (5) 80 x 0 . 44 0 . 27 mH = 1 . 23 A x 110 k 2 x ( 265 V AC ) = 375 V Innovative PowerTM 12 x 1 . 5 = 271 mA 80 x 0 . 83 The primary inductance of the transformer: 2 POUT ( = = I PPK = 1 2 x 18 x ( - 3 . 5 ms ) 2 2 x 47 2 x 90 80 V 0 . 83 x 30 F V IN ( MAX = 1 - tC ) 2 fL x C IN V OUT x I OUT V INDC _ MIN x _ MAX The maximum input primary peak current: The operation for the circuit shown in Figure 4 is as follows: the rectifier bridge D1-D4 and the capacitor C1/C2 convert the AC line voltage to DC bus voltage. This voltage supplies the primary winding of the transformer T1 and the startup circuit of Q2 and C4 to VDD pin of ACT520. The primary power current path is formed by the transformer's primary winding, Q1, and the current sense resistor R9. The resistors R3, R2, diode D5 and capacitor C3 create a snubber clamping network that protects Q1 from damage due to high voltage spike during Q1's turn off. The network consisting of capacitor C4, diode D6 and resistor R4 provides a VDD supply voltage for ACT520 from the auxiliary winding of the transformer. The resistor R4 is optional, which filters out spikes and noise to makes VDD more stable. C4 is the decoupling capacitor of the supply voltage and energy storage component for startup. During power startup, the current charges C4 through startup mosfet Q2 from the rectified bus voltage. The diode D8 and the capacitor C5/C6 rectify filter the output voltage. The resistor divider consists of R15 and R16 programs the output voltage. Since a bridge rectifier and bulk input capacitors are used, the resulting minimum and maximum DC input voltages can be calculated: 2 INAC _ MIN = I IN -8- (12) www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 TYPICAL APPLICATION CONT'D An EI16+ core is selected for the transformer. From the manufacture's catalogue recommendation, the gapped core with an effective inductance ALE of 0.234 H/T2 is selected. The turn of the primary winding is: LP = A LE NP = 0 . 27 mH 0 . 234 H / T 2 = 34 T COUT = PCB Layout Guideline Good PCB layout is critical to have optimal performance. Decoupling capacitor (C4) and feedback resistor (R5/R6) should be placed close to VDD and FB pin respectively. There are two main power path loops. One is formed by C1/C2, primary winding, mosfet transistor and current sense resistor (R9). The other is secondary winding, rectifier D8 and output capacitors (C5/C6). Keep these loop areas as small as possible. Connecting high current ground returns, the input capacitor ground lead, and the ACT520/ACT520A GND pin to a single point (star ground configuration). The turns of secondary and auxiliary winding can be derived accordingly: Ns 1 xNp = x 34 6 T Np 6 .1 (14) NA = NA x N s = 2.63 x 6 16T NS (15) Determining the value of the current sense resistor (R9) uses the peak current in the design. Since the ACT520 internal current limit is set to 1V, the design of the current sense resistor is given by: R CS = VCS 2 x I OUT _ MAX x VOUT LP x FSW x system = (20) Two 330F electrolytic capacitors are used to keep the ripple small. (13) NS = IOUT 1 .6 = = 291F fsw x V RIPPLE 110 k x 50 mV (16) 1 2 x 1 .6 x 12 0 .27 mH x 110 kHz x 0 .83 0 .806 The voltage feedback resistors are selected according to the Ioccmax and Vo. The design Io_cc max is given by: fs = Np Ns x R det 1 x R det 2 x R det 1 + R det 2 VO + V D V L p x cs x K f _ sw R cs (17) The design Vo is given by: Vo = (1 + Rdet 1 N ) x s x Vdet - VD Rdet 2 Na (18) Where k is IC constant and K=14530, then we can get the value: (19) R det 1 = 115 K , R det 2 = 6 . 8 K When selecting the output capacitor, a low ESR electrolytic capacitor is recommended to minimize ripple from the current ripple. The approximate equation for the output capacitance value is given by: Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. -9- www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 Figure 4: Universal VAC Input, 12/9/5V 1.5A rapid Charger Figure 5: Output CCCV curve V-I Characteristic vs. VIN (25C) 14 Output Voltage (V) 12 10 8 6 4 2 0 0 600 1200 1800 Output Current (mA) Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. - 10 - www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 Table 1: ACT520 18W Rapid Charger Bill of Materials ITEM REFERENCE 1 DESCRIPTION QTY MANUFACTURER U1 IC, ACT520SH,SOP-8 1 Active-Semi. 2 U2 OPTO,EL3H7D,CTR:300-600%,4PIN SMD 1 EVERLIGHT 3 U3 TL431A, Ref=2.5V,1%,SOT23-3 1 TI 4 U4 IC, ACT4613SH201-T,SOP-8 1 Active-Semi. 5 C1,2 Capacitor, Electrolytic,15uF/400V, 8x14mm 2 RUBYCON 6 C11,C8 Capacitor, Ceramic, 1000pF/500V, 0805,SMD 2 POE 7 C4 Capacitor, Ceramic,33uF/50V, 1206 1 POE 8 C5,C6 Capacitor, Solid, 330uF/16V, 8x12mm 2 KSC 9 C9,10 Capacitor, Ceramic, 0.1uF/50V, 0805,SMD 2 POE 10 C7 Capacitor, Ceramic, 100pF/25V, 0805,SMD 1 POE 11 CY1 Safety Y1,Capacitor,1000pF/400V,Dip 1 UXT 12 BD1 BP06,1000V/1.0A,SDIP 1 PANJIT 13 D5,D6 Fast Recovery Rectifier, RS1M,1000V/1.0A, RMA 2 PANJIT 14 D8 Diode, Schottky, 100V/15A, TO-247AB 1 Diodes 15 LF1 CM Inductor, 27mH, EE8.3,D=0.2mm,90T 1 APY() 16 Q1 N-Mosfet Transistor, 4N60,TO-220 1 AUK 17 Q2 N-Mosfet, Depletion mode,CSF501D,20mA/600V,SOT23 1 HuiJing 18 PCB1 PCB, L*W*T=39x39x1.0mm,FR-4,Rev:A 1 Jintong 19 F1 Fuse,2A/250V 1 TY-OHM 20 R1,4 Chip Resistor, 22 ohm, 0805, 5% 2 TY-OHM 21 R2,23 Chip Resistor, 100 ohm, 0805, 5% 2 TY-OHM 22 R3,3A,7 Carbon Resistor, 510K ohm, 1206, 5% 3 TY-OHM 23 R5 Chip Resistor, 115K ohm, 0805,1% 1 TY-OHM 24 R6 Chip Resistor, 6.8K ohm, 0805, 1% 1 TY-OHM 25 R8 Chip Resistor, 820 ohm, 0805, 5% 1 TY-OHM 26 R9 Chip Resistor, 0.806 ohm,1206 , 1% 1 TY-OHM 27 R11 Chip Resistor, 510 ohm, 0805, 5% 1 TY-OHM 28 R12 Chip Resistor, 1.1k ohm, 0805,5% 1 TY-OHM 29 R14,26 Chip Resistor, 3.3k ohm, 0805, 5% 2 TY-OHM 30 R15 Chip Resistor, 10.5K ohm, 0805, 1% 1 TY-OHM 31 R16 Chip Resistor, 10.2K ohm, 0805, 1% 1 TY-OHM 32 R17 Chip Resistor, 6.49K ohm, 0805, 1% 1 TY-OHM 33 R18 Chip Resistor, 8.66K ohm, 0805, 1% 1 TY-OHM 34 R24 Chip Resistor, 20k ohm, 0805, 5% 1 TY-OHM 35 T1 Transformer, Lp=0.27mH, EI16+ 1 APY() 36 NR1 Thermal resistor, SC053 1 TY-OHM 37 VR1 10D471 1 TY-OHM 38 USB1 Small standard USB connector. 1 TY-OHM 39 R19,20 NC Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. - 11 - www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 TYPICAL PERFORMANCE CHARACTERISTICS Startup Supply Current vs. Temperature VDD Turn on Voltage vs. Temperature VDDON (V) 18.7 18.6 Startup Supply Current (A) 18.8 18.5 18.4 18.3 4 3 2 1 0 18.2 -40 0 40 80 120 -40 0 40 80 Temperature (C) Static current vs. Temperature Maximum Switching Frequency vs. Temperature 1020 1010 1000 990 980 -40 0 40 80 120 Temperature (C) Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. 150 120 ACT520/ACT520A-004 ACT520/ACT520A-003 Maximum Switching Frequency (KHz) Temperature (C) 1030 Supply Current (A) ACT520/ACT520A-002 5 ACT520/ACT520A-001 18.9 ACT520 130 110 ACT520A 90 70 50 30 -40 0 40 80 120 Temperature (C) - 12 - www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. ACT520/ACT520A Rev 0, 05-Jun-15 PACKAGE OUTLINE SOP-8 PACKAGE OUTLINE AND DIMENSIONS Note: Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15mm per end. Dimension E1 does not include flash or protrusion. Active-Semi, Inc. reserves the right to modify the circuitry or specifications without notice. Users should evaluate each product to make sure that it is suitable for their applications. Active-Semi products are not intended or authorized for use as critical components in life-support devices or systems. Active-Semi, Inc. does not assume any liability arising out of the use of any product or circuit described in this datasheet, nor does it convey any patent license. Active-Semi and its logo are trademarks of Active-Semi, Inc. For more information on this and other products, contact sales@active-semi.com or visit http://www.active-semi.com. is a registered trademark of Active-Semi. Innovative PowerTM ActiveQRTM is a trademark of Active-Semi. - 13 - www.active-semi.com Copyright (c) 2015 Active-Semi, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Active-Semi: ACT520SH-T