AT24CM01 IC-Compatible (Two-Wire) Serial EEPROM 1Mbit (131,072 x 8) Features * Low-Voltage and Standard Voltage Operation: - VCC = 1.7V to 5.5V - VCC = 2.5V to 5.5V * Internally Organized as 131,072 x 8 (1M) * Industrial Temperature Range: -40C to +85C * I2C-Compatible (Two-Wire) Serial Interface: - 100 kHz Standard mode, 1.7V to 5.5V - 400 kHz Fast mode, 1.7V to 5.5V - 1 MHz Fast Mode Plus (FM+), 2.5V to 5.5V * Schmitt Triggers, Filtered Inputs for Noise Suppression * Bidirectional Data Transfer Protocol * Write-Protect Pin for Full Array Hardware Data Protection * Ultra Low Active Current (3 mA maximum) and Standby Current (6 A maximum) * 256-byte Page Write Mode: - Byte write and partial page writes allowed * Random and Sequential Read Modes * Self-Timed Write Cycle: - All Write operations complete within 5 ms maximum * Built in Error Detection and Correction * High Reliability: - Endurance: 1,000,000 write cycles - Data retention: 100 years * Green Package Options (Lead-free/Halide-free/RoHS compliant) * Die Sale Options: Wafer Form and Bumped Wafers Packages * 8-Lead SOIC, 8-Lead SOIJ, 8-Lead TSSOP and 8-Ball WLCSP (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 1 AT24CM01 Table of Contents Features.......................................................................................................................... 1 Packages.........................................................................................................................1 1. Package Types (not to scale).................................................................................... 4 2. Pin Descriptions.........................................................................................................5 2.1. 2.2. 2.3. 2.4. 2.5. 2.6. Device Address Inputs (A1, A2)................................................................................................... 5 Ground......................................................................................................................................... 5 Serial Data (SDA).........................................................................................................................5 Serial Clock (SCL)........................................................................................................................5 Write-Protect (WP)....................................................................................................................... 6 Device Power Supply................................................................................................................... 6 3. Description.................................................................................................................7 3.1. 3.2. System Configuration Using Two-Wire Serial EEPROMs ........................................................... 7 Block Diagram.............................................................................................................................. 8 4. Electrical Characteristics........................................................................................... 9 4.1. 4.2. 4.3. 4.4. 4.5. Absolute Maximum Ratings..........................................................................................................9 DC and AC Operating Range.......................................................................................................9 DC Characteristics....................................................................................................................... 9 AC Characteristics......................................................................................................................10 Electrical Specifications..............................................................................................................11 5. Device Operation and Communication....................................................................13 5.1. 5.2. 5.3. 5.4. 5.5. Clock and Data Transition Requirements...................................................................................13 Start and Stop Conditions.......................................................................................................... 13 Acknowledge and No-Acknowledge...........................................................................................14 Standby Mode............................................................................................................................ 14 Software Reset...........................................................................................................................15 6. Memory Organization.............................................................................................. 16 6.1. Device Addressing..................................................................................................................... 16 7. Write Operations......................................................................................................18 7.1. 7.2. 7.3. 7.4. 7.5. Byte Write...................................................................................................................................18 Page Write..................................................................................................................................18 Acknowledge Polling.................................................................................................................. 19 Write Cycle Timing..................................................................................................................... 20 Write Protection..........................................................................................................................20 8. Read Operations..................................................................................................... 21 8.1. 8.2. Current Address Read................................................................................................................21 Random Read............................................................................................................................ 21 (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 2 AT24CM01 8.3. Sequential Read.........................................................................................................................22 9. Device Default Condition from Microchip................................................................ 23 10. Packaging Information.............................................................................................24 10.1. Package Marking Information.....................................................................................................24 11. Revision History.......................................................................................................34 The Microchip Web Site................................................................................................ 35 Customer Change Notification Service..........................................................................35 Customer Support......................................................................................................... 35 Product Identification System........................................................................................ 36 Microchip Devices Code Protection Feature................................................................. 36 Legal Notice...................................................................................................................37 Trademarks................................................................................................................... 37 Quality Management System Certified by DNV.............................................................38 Worldwide Sales and Service........................................................................................39 (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 3 AT24CM01 Package Types (not to scale) 1. Package Types (not to scale) 8-Lead SOIC/SOIJ/TSSOP (Top View) NC 1 8 VCC A1 2 7 WP 8-Ball WLCSP (Top View) VCC WP A1 SCL A2 3 6 SCL GND 4 5 SDA (c) 2019 Microchip Technology Inc. Datasheet SDA NC A2 GND 20006170A-page 4 AT24CM01 Pin Descriptions 2. Pin Descriptions The descriptions of the pins are listed in Table 2-1. Table 2-1.Pin Function Table Name 8Lead SOIC 8Pad SOIJ 8Lead TSSOP 8Ball WLCSP NC A1(1) 1 1 1 E1 Not Connected Function 2 2 2 D2 Device Address Input A2(1) 3 3 3 C3 Device Address Input GND 4 4 4 E3 Ground SDA 5 5 5 A3 Serial Data SCL WP(1) 6 6 6 B2 Serial Clock 7 7 7 C1 Write-Protect VCC 8 8 8 A1 Device Power Supply Note: 1. If the A2, A1 or WP pins are not driven, they are internally pulled down to GND. In order to operate in a wide variety of application environments, the pull-down mechanism is intentionally designed to be somewhat strong. Once these pins are biased above the CMOS input buffer's trip point (~0.5 x VCC), the pulldown mechanism disengages. Microchip recommends connecting these pins to a known state whenever possible. 2.1 Device Address Inputs (A1, A2) The A1 and A2 pins are device address inputs that are hardwired (directly to GND or to VCC) for compatibility with other two-wire Serial EEPROM devices. When the pins are hardwired, as many as four devices may be addressed on a single bus system. A device is selected when a corresponding hardware and software match is true. If these pins are left floating, the A1 and A2 pins will be internally pulled down to GND. However, due to capacitive coupling that may appear in customer applications, Microchip recommends always connecting the address pins to a known state. When using a pull-up resistor, Microchip recommends using 10 k or less. 2.2 Ground The ground reference for the power supply. GND should be connected to the system ground. 2.3 Serial Data (SDA) The SDA pin is an open-drain bidirectional input/output pin used to serially transfer data to and from the device. The SDA pin must be pulled high using an external pull-up resistor (not to exceed 10 k in value) and may be wire-ORed with any number of other open-drain or open-collector pins from other devices on the same bus. 2.4 Serial Clock (SCL) The SCL pin is used to provide a clock to the device and to control the flow of data to and from the device. Command and input data present on the SDA pin is always latched in on the rising edge of SCL, while output data on the SDA pin is clocked out on the falling edge of SCL. The SCL pin must either be forced high when the serial bus is idle or pulled high using an external pull-up resistor. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 5 AT24CM01 Pin Descriptions 2.5 Write-Protect (WP) The write-protect input, when connected to GND, allows normal write operations. When the WP pin is connected directly to VCC, all write operations to the protected memory are inhibited. If the pin is left floating, the WP pin will be internally pulled down to GND. However, due to capacitive coupling that may appear in customer applications, Microchip recommends always connecting the WP pin to a known state. When using a pullup resistor, Microchip recommends using 10 k or less. Table 2-2.Write-Protect 2.6 WP Pin Status Part of the Array Protected At VCC Full Array At GND Normal Write Operations Device Power Supply The VCC pin is used to supply the source voltage to the device. Operations at invalid VCC voltages may produce spurious results and should not be attempted. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 6 AT24CM01 Description 3. Description The AT24CM01 provides 1,048,576 bits of Serial Electrically Erasable and Programmable Read-Only Memory (EEPROM) organized as 131,072 words of eight bits each. The device's cascading feature allows up to four devices to share a common two-wire bus. This device is optimized for use in many industrial and commercial applications where low-power and low-voltage operations are essential. The device is available in space-saving 8-lead SOIC, 8-Lead TSSOP, 8-Lead SOIJ and 8-ball WLCSP packages. All packages operate from 1.7V to 5.5V. 3.1 System Configuration Using Two-Wire Serial EEPROMs VCC RPUP(max) = tR(max) 0.8473 x CL V - VOL(max) RPUP(min) = CC IOL VCC SCL SDA WP I2C Bus Master: Microcontroller NC VCC NC VCC NC Slave 0 WP A2 AT24CXXX SDA A1 Slave 1 WP A2 AT24CXXX SDA A1 GND GND GND A1 GND (c) 2019 Microchip Technology Inc. SCL Datasheet SCL VCC Slave 3 WP A2 AT24CXXX SDA SCL 20006170A-page 7 AT24CM01 Description Block Diagram Hardware Address Comparator Memory System Control Module Power-on Reset Generator VCC High-Voltage Generation Circuit A1 Row Decoder 3.2 EEPROM Array 1 page A2 (c) 2019 Microchip Technology Inc. WP Address Register and Counter Column Decoder SCL Data Register DOUT GND Write Protection Control Data & ACK Input/Output Control DIN Start Stop Detector SDA Datasheet 20006170A-page 8 AT24CM01 Electrical Characteristics 4. Electrical Characteristics 4.1 Absolute Maximum Ratings Temperature under bias -55C to +125C Storage temperature -65C to +150C VCC 6.25V Voltage on any pin with respect to ground -1.0V to +7.0V DC output current 5.0 mA ESD protection >3 kV Note: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 4.2 DC and AC Operating Range Table 4-1.DC and AC Operating Range AT24CM01 4.3 Operating Temperature (Case) Industrial Temperature Range -40C to +85C VCC Power Supply Low-Voltage Grade 1.7V to 5.5V DC Characteristics Table 4-2.DC Characteristics Symbol Minimum Typical(1) Maximum Units Supply Voltage, 1.7V Option VCC1 1.7 -- 5.5 V Supply Voltage, 2.5V Option VCC2 2.5 -- 5.5 V Supply Current ICC -- -- 2.0 mA VCC = 5.0V, Read at 400 kHz -- -- 3.0 mA VCC = 5.0V, Write at 400 kHz Parameter (c) 2019 Microchip Technology Inc. Datasheet Test Conditions 20006170A-page 9 AT24CM01 Electrical Characteristics ...........continued Parameter Symbol Minimum Typical(1) Maximum Units ISB -- -- 1.0 A VCC = 1.7V, VIN = VCC or VSS -- -- 2.0 A VCC = 2.5V, VIN = VCC or VSS -- -- 3.0 A VCC = 3.6V, VIN = VCC or VSS -- -- 6.0 A VCC = 5.5V, VIN = VCC or VSS Standby Current Test Conditions Input Leakage Current ILI -- 0.10 3.0 A VIN = VCC or VSS Output Leakage Current ILO -- 0.05 3.0 A VOUT = VCC or VSS Input Low Level VIL -0.6 -- VCC x 0.3 V Note 2 Input High Level VIH VCC x 0.7 -- VCC + 0.5 V Note 2 Output Low Level VOL1 -- -- 0.2 V VCC = 1.7V, IOL = 0.15 mA Output Low Level VOL2 -- -- 0.4 V VCC = 3.0V, IOL = 2.1 mA Note: 1. 2. 4.4 Typical values characterized at TA = +25C unless otherwise noted. This parameter is characterized but is not 100% tested in production. AC Characteristics Table 4-3.AC Characteristics(1) Parameter Symbol Fast Mode Fast Mode Plus VCC = 1.7V to 5.5V VCC = 2.5V to 5.5V Min. Max. Min. Max. Units Clock Frequency, SCL fSCL -- 400 -- 1000 kHz Clock Pulse Width Low tLOW 1,300 -- 500 -- ns Clock Pulse Width High tHIGH 600 -- 400 -- ns tI -- 100 -- 50 ns Clock Low to Data Out Valid tAA 50 900 50 450 ns Bus Free Time between Stop and Start(2) tBUF 1,300 -- 500 -- ns Start Hold Time tHD.STA 600 -- 250 -- ns Start Set-up Time tSU.STA 600 -- 250 -- ns Input Filter Spike Suppression (SCL,SDA)(2) (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 10 AT24CM01 Electrical Characteristics ...........continued Parameter Symbol Fast Mode Fast Mode Plus VCC = 1.7V to 5.5V VCC = 2.5V to 5.5V Units Min. Max. Min. Max. Data In Hold Time tHD.DAT 0 -- 0 -- ns Data In Set-up Time tSU.DAT 100 -- 100 -- ns tR -- 300 -- 300 ns tF -- 300 -- 100 ns tSU.STO 600 -- 250 -- ns Data Out Hold Time tDH 50 -- 50 -- ns Write Cycle Time tWR -- 5 -- 5 ms Inputs Rise Inputs Fall Time(2) Time(2) Stop Condition Set-up Time Note: 1. AC measurement conditions: - CL: 100 pF - RPUP (SDA bus line pull-up resistor to VCC): 1.3 k (1000 kHz), 4 k (400 kHz) - Input pulse voltages: 0.3 x VCC to 0.7 x VCC - Input rise and fall times: 50 ns - Input and output timing reference voltages: 0.5 x VCC 2. These parameters are determined through product characterization and are not 100% tested in production. Figure 4-1. Bus Timing tF tHIGH tR tLOW SCL tSU.STA tHD.STA tHD.DAT tSU.DAT tSU.STO SDA In tDH tAA tBUF SDA Out 4.5 Electrical Specifications 4.5.1 Power-Up Requirements and Reset Behavior During a power-up sequence, the VCC supplied to the AT24CM01 should monotonically rise from GND to the minimum VCC level, as specified in Table 4-1, with a slew rate no faster than 0.1 V/s. 4.5.1.1 Device Reset To prevent inadvertent write operations or any other spurious events from occurring during a power-up sequence, the AT24CM01 includes a Power-on Reset (POR) circuit. Upon power-up, the device will not (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 11 AT24CM01 Electrical Characteristics respond to any commands until the VCC level crosses the internal voltage threshold (VPOR) that brings the device out of Reset and into Standby mode. The system designer must ensure the instructions are not sent to the device until the VCC supply has reached a stable value greater than or equal to the minimum VCC level. Additionally, once the VCC is greater than or equal to the minimum VCC level, the bus master must wait at least tPUP before sending the first command to the device. See Table 4-4 for the values associated with these power-up parameters. Table 4-4.Power-Up Conditions(1) Symbol Parameter Min. Max. Units tPUP Time required after VCC is stable before the device can accept commands VPOR Power-on Reset Threshold Voltage tPOFF Minimum time at VCC = 0V between power cycles 100 s 1.5 V 500 ms Note: 1. These parameters are characterized but they are not 100% tested in production. If an event occurs in the system where the VCC level supplied to the AT24CM01 drops below the maximum VPOR level specified, it is recommended that a full-power cycle sequence be performed by first driving the VCC pin to GND, waiting at least the minimum tPOFF time and then performing a new power-up sequence in compliance with the requirements defined in this section. 4.5.2 Pin Capacitance Table 4-5.Pin Capacitance(1) Symbol Test Condition Max. Units Conditions CI/O Input/Output Capacitance (SDA) 8 pF VI/O = 0V CIN Input Capacitance (A0, A1, A2 and SCL) 6 pF VIN = 0V Note: 1. This parameter is characterized but is not 100% tested in production. 4.5.3 EEPROM Cell Performance Characteristics Table 4-6.EEPROM Cell Performance Characteristics Operation Test Condition Write Endurance(1) TA = 25C, VCC = 3.3V, Page Write mode Data Retention(1) TA = 55C Min. Max. Units 1,000,000 -- Write Cycles 100 -- Years Note: 1. Performance is determined through characterization and the qualification process. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 12 AT24CM01 Device Operation and Communication 5. Device Operation and Communication The AT24CM01 operates as a slave device and utilizes a simple I2C-compatible two-wire digital serial interface to communicate with a host controller, commonly referred to as the bus master. The master initiates and controls all read and write operations to the slave devices on the serial bus, and both the master and the slave devices can transmit and receive data on the bus. The serial interface is comprised of just two signal lines: Serial Clock (SCL) and Serial Data (SDA). The SCL pin is used to receive the clock signal from the master, while the bidirectional SDA pin is used to receive command and data information from the master as well as to send data back to the master. Data is always latched into the AT24CM01 on the rising edge of SCL and always output from the device on the falling edge of SCL. Both the SCL and SDA pins incorporate integrated spike suppression filters and Schmitt Triggers to minimize the effects of input spikes and bus noise. All command and data information is transferred with the Most Significant bit (MSb) first. During bus communication, one data bit is transmitted every clock cycle, and after eight bits (one byte) of data have been transferred, the receiving device must respond with either an Acknowledge (ACK) or a No-Acknowledge (NACK) response bit during a ninth clock cycle (ACK/NACK clock cycle) generated by the master. Therefore, nine clock cycles are required for every one byte of data transferred. There are no unused clock cycles during any read or write operation, so there must not be any interruptions or breaks in the data stream during each data byte transfer and ACK or NACK clock cycle. During data transfers, data on the SDA pin must only change while SCL is low, and the data must remain stable while SCL is high. If data on the SDA pin changes while SCL is high, then either a Start or a Stop condition will occur. Start and Stop conditions are used to initiate and end all serial bus communication between the master and the slave devices. The number of data bytes transferred between a Start and a Stop condition is not limited and is determined by the master. In order for the serial bus to be idle, both the SCL and SDA pins must be in the logic high state at the same time. 5.1 Clock and Data Transition Requirements The SDA pin is an open-drain terminal and therefore must be pulled high with an external pullup resistor. SCL is an input pin that can either be driven high or pulled high using an external pullup resistor. Data on the SDA pin may change only during SCL low time periods. Data changes during SCL high periods will indicate a Start or Stop condition as defined below. The relationship of the AC timing parameters with respect to SCL and SDA for the AT24CM01 are shown in the timing waveform in Figure 4-1. The AC timing characteristics and specifications are outlined in AC Characteristics. 5.2 Start and Stop Conditions 5.2.1 Start Condition A Start condition occurs when there is a high-to-low transition on the SDA pin while the SCL pin is at a stable logic `1' state and will bring the device out of Standby mode. The master uses a Start condition to initiate any data transfer sequence; therefore, every command must begin with a Start condition. The device will continuously monitor the SDA and SCL pins for a Start condition but will not respond unless one is detected. Refer to Figure 5-1 for more details. 5.2.2 Stop Condition A Stop condition occurs when there is a low-to-high transition on the SDA pin while the SCL pin is stable in the logic `1' state. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 13 AT24CM01 Device Operation and Communication The master can use the Stop condition to end a data transfer sequence with the AT24CM01, which will subsequently return to Standby mode. The master can also utilize a repeated Start condition instead of a Stop condition to end the current data transfer if the master will perform another operation. Refer to Figure 5-1 for more details. 5.3 Acknowledge and No-Acknowledge After every byte of data is received, the receiving device must confirm to the transmitting device that it has successfully received the data byte by responding with what is known as an Acknowledge (ACK). An ACK is accomplished by the transmitting device first releasing the SDA line at the falling edge of the eighth clock cycle followed by the receiving device responding with a logic `0' during the entire high period of the ninth clock cycle. When the AT24CM01 is transmitting data to the master, the master can indicate that it is done receiving data and wants to end the operation by sending a logic `1' response to the AT24CM01 instead of an ACK response during the ninth clock cycle. This is known as a No-Acknowledge (NACK) and is accomplished by the master sending a logic `1' during the ninth clock cycle, at which point the AT24CM01 will release the SDA line so the master can then generate a Stop condition. The transmitting device, which can be the bus master or the Serial EEPROM, must release the SDA line at the falling edge of the eighth clock cycle to allow the receiving device to drive the SDA line to a logic `0' to ACK the previous 8-bit word. The receiving device must release the SDA line at the end of the ninth clock cycle to allow the transmitter to continue sending new data. A timing diagram has been provided in Figure 5-1 to better illustrate these requirements. Figure 5-1.Start Condition, Data Transitions, Stop Condition and Acknowledge SCL SDA Must Be Stable SDA Must Be Stable 1 2 Acknowledge Window 8 9 SDA Start Condition 5.4 Acknowledge Valid SDA Change Allowed SDA Change Allowed The transmitting device (Master or Slave) must release the SDA line at this point to allow the receiving device (Master or Slave) to drive the SDA line low to ACK the previous 8-bit word. Stop Condition The receiver (Master or Slave) must release the SDA line at this point to allow the transmitter to continue sending new data. Standby Mode The AT24CM01 features a low-power Standby mode that is enabled when any one of the following occurs: * A valid power-up sequence is performed (see Power-Up Requirements and Reset Behavior). * A Stop condition is received by the device unless it initiates an internal write cycle (see Write Operations). * At the completion of an internal write cycle (see Write Operations). (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 14 AT24CM01 Device Operation and Communication 5.5 Software Reset After an interruption in protocol, power loss or system Reset, any twowire device can be protocol reset by clocking SCL until SDA is released by the EEPROM and goes high. The number of clock cycles until SDA is released by the EEPROM will vary. The software Reset sequence should not take more than nine dummy clock cycles. Once the software Reset sequence is complete, new protocol can be sent to the device by sending a Start condition followed by the protocol. Refer to Figure 5-2 for an illustration. Figure 5-2.Software Reset Dummy Clock Cycles SCL 1 2 3 8 SDA Released by EEPROM 9 Device is Software Reset SDA In the event that the device is still non-responsive or remains active on the SDA bus, a power cycle must be used to reset the device (see Power-Up Requirements and Reset Behavior). (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 15 AT24CM01 Memory Organization 6. Memory Organization The AT24CM01 is internally organized as 512 pages of 256 bytes each. 6.1 Device Addressing Accessing the device requires an 8-bit device address byte following a Start condition to enable the device for a read or write operation. Since multiple slave devices can reside on the serial bus, each slave device must have its own unique address so the master can access each device independently. The Most Significant four bits of the device address byte is referred to as the device type identifier. The device type identifier `1010' (Ah) is required in bits 7 through 4 of the device address byte (see Table 61). Following the 4-bit device type identifier are the hardware slave address bits, A2 and A1. These bits can be used to expand the address space by allowing up to four Serial EEPROM devices on the same bus. The A2 and A1 values must correlate with the voltage level on the corresponding hardwired device address input pins A2 and A1. The A2 and A1 pins use an internal proprietary circuit that automatically biases it to a logic `0' state if the pin is allowed to float. In order to operate in a wide variety of application environments, the pulldown mechanism is intentionally designed to be somewhat strong. Once these pins are biased above the CMOS input buffer's trip point (~0.5 x VCC), the pull-down mechanism disengages. Microchip recommends connecting the A2 and A1 pin to a known state whenever possible. Following the A2 and A1 hardware slave address bits is bit A16 (bit 1 of the device address byte), which is the Most Significant bit of the memory array word address. Refer to Table 6-1 to review the bit position. The eighth bit (bit 0) of the device address byte is the Read/Write Select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon the successful comparison of the device address byte, the AT24CM01 will return an ACK. If a valid comparison is not made, the device will NACK. Table 6-1.Device Addressing Package Device Type Identifier Bit 7 Bit 6 Bit 5 Bit 4 SOIC, SOIJ, TSSOP, WLCSP 1 0 1 0 Hardware Slave Address Bits Most Significant Bit R/W Select of the Word Address Bit 3 Bit 2 Bit 1 Bit 0 A2 A1 A16 R/W For all operations except the current address read, two 8bit word address bytes must be transmitted to the device immediately following the device address byte. The word address bytes consist of the remaining 16 bits of the 17-bit memory array word address, and are used to specify which byte location in the EEPROM to start reading or writing. The first word address byte contains the next eight bits of the word address (A15 through A8) in bit positions seven through zero, as seen in Table 6-2. Upon completion of the first word address byte, the AT24CM01 will return an ACK. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 16 AT24CM01 Memory Organization Table 6-2.First Word Address Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 A15 A14 A13 A12 A11 A10 A9 A8 Next, the second word address byte is sent to the device which provides the remaining eight bits of the word address (A7 through A0). Upon completion of the second word address byte, the AT24CM01 will return an ACK. See Table 6-3 to review these bit positions. Table 6-3.Second Word Address Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 A7 A6 A5 A4 A3 A2 A1 A0 (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 17 AT24CM01 Write Operations 7. Write Operations All write operations for the AT24CM01 begin with the master sending a Start condition, followed by a device address byte with the R/W bit set to logic `0', and then by the word address byte. The data value(s) to be written to the device immediately follow the word address byte. 7.1 Byte Write The AT24CM01 supports the writing of a single 8-bit byte. Selecting a data word in the AT24CM01 requires 17-bit word address. Upon receipt of the proper device address and the word address bytes, the EEPROM will send an Acknowledge. The device will then be ready to receive the 8-bit data word. Following receipt of the 8bit data word, the EEPROM will respond with an ACK. The addressing device, such as a bus master, must then terminate the write operation with a Stop condition. At that time, the EEPROM will enter an internally self-timed write cycle, which will be completed within tWR, while the data word is being programmed into the nonvolatile EEPROM. All inputs are disabled during this write cycle, and the EEPROM will not respond until the write is complete. Figure 7-1.Byte Write SCL 1 2 3 4 5 6 7 8 9 1 2 Device Address Byte SDA 1 0 1 0 A2 A1 3 4 5 6 7 8 9 A8 0 First Word Address Byte A16 0 0 MSB A15 A14 A13 A12 A11 A10 A9 MSB Start Condition by Master ACK from Slave 1 2 3 4 5 ACK from Slave 6 7 8 9 1 2 3 A6 A5 A4 A3 A2 A1 A0 0 MSB 6 7 8 9 D7 D6 D5 D4 D3 D2 D1 D0 0 MSB ACK from Slave 7.2 5 Data Word Second Word Address Byte A7 4 Stop Condition ACK from Slave by Master Page Write A page write operation allows up to 256 bytes to be written in the same write cycle, provided all bytes are in the same row of the memory array (where address bits A16 through A8 are the same). Partial page writes of less than 256 bytes are also allowed. A page write is initiated the same way as a byte write, but the bus master does not send a Stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the bus master can transmit up to 255 additional data words. The EEPROM will respond with an ACK after each data word is received. Once all data to be written has been sent to the device, the bus master must issue a Stop condition (see Figure 7-2) at which time the internally self-timed write cycle will begin. The lower eight bits of the word address are internally incremented following the receipt of each data word. The higher order address bits are not incremented and retain the memory page row location. Page (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 18 AT24CM01 Write Operations write operations are limited to writing bytes within a single physical page, regardless of the number of bytes actually being written. When the incremented word address reaches the page boundary, the address counter will rollover to the beginning of the same page. Nevertheless, creating a rollover event should be avoided as previously loaded data in the page could become unintentionally altered. Figure 7-2. Page Write 1 SCL 2 3 4 5 6 7 8 9 1 2 Device Address Byte SDA 1 0 1 0 A2 A1 A16 0 0 A6 6 7 A15 A14 A13 A12 A11 A10 A9 ACK from Slave 3 4 5 6 7 8 9 1 2 Second Word Address Byte A7 5 9 A8 0 A5 A4 A3 A2 A1 ACK from Slave 3 4 5 6 7 8 9 Data Word (n) A0 0 MSB D7 D6 D5 D4 D3 D2 1 2 3 4 5 6 7 8 9 Data Word (n+x), max of 256 without rollover D1 D0 MSB 0 D7 D6 D5 D4 D3 D2 D1 D0 0 MSB ACK from Slave 7.3 8 MSB Start Condition by Master 2 4 First Word Address Byte MSB 1 3 Stop Condition ACK by Master from Slave ACK from Slave Acknowledge Polling An Acknowledge Polling routine can be implemented to optimize time-sensitive applications that would prefer not to wait the fixed maximum write cycle time (tWR). This method allows the application to know immediately when the Serial EEPROM write cycle has completed, so a subsequent operation can be started. Once the internally self-timed write cycle has started, an Acknowledge Polling routine can be initiated. This involves repeatedly sending a Start condition followed by a valid device address byte with the R/W bit set at logic `0'. The device will not respond with an ACK while the write cycle is ongoing. Once the internal write cycle has completed, the EEPROM will respond with an ACK, allowing a new read or write operation to be immediately initiated. A flowchart has been included below in Figure 7-3 to better illustrate this technique. Figure 7-3.Acknowledge Polling Flowchart Send any Write protocol. Send Stop condition to initiate the Write cycle. Send Start condition followed by a valid Device Address byte with R/W = 0. Did the device ACK? YES Proceed to next Read or Write operation. NO (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 19 AT24CM01 Write Operations 7.4 Write Cycle Timing The length of the self-timed write cycle (tWR) is defined as the amount of time from the Stop condition that begins the internal write cycle to the Start condition of the first device address byte sent to the AT24CM01 that it subsequently responds to with an ACK. Figure 7-4 has been included to show this measurement. During the internally self-timed write cycle, any attempts to read from or write to the memory array will not be processed. Figure 7-4.Write Cycle Timing SCL 8 9 9 ACK ACK Data Word n SDA D0 tWR Stop Condition 7.5 Start Condition First Acknowledge from the device to a valid device address sequence after write cycle is initiated. The minimum tWR can only be determined through the use of an ACK Polling routine. Stop Condition Write Protection The AT24CM01 utilizes a hardware data protection scheme that allows the user to writeprotect the entire memory contents when the WP pin is at VCC (or a valid VIH). No write protection will be set if the WP pin is at GND or left floating. Table 7-1.AT24CM01 Write-Protect Behavior WP Pin Voltage Part of the Array Protected VCC Full Array GND None Write Protection Not Enabled The status of the WP pin is sampled at the Stop condition for every byte write or page write operation prior to the start of an internally selftimed write cycle. Changing the WP pin state after the Stop condition has been sent will not alter or interrupt the execution of the write cycle. If an attempt is made to write to the device while the WP pin has been asserted, the device will acknowledge the device address, word address and data bytes, but no write cycle will occur when the Stop condition is issued. The device will immediately be ready to accept a new read or write command. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 20 AT24CM01 Read Operations 8. Read Operations Read operations are initiated the same way as write operations with the exception that the Read/Write Select bit in the device address byte must be a logic `1'. There are three read operations: * Current Address Read * Random Address Read * Sequential Read 8.1 Current Address Read The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the VCC is maintained to the part. The address roll-over during a read is from the last byte of the last page to the first byte of the first page of the memory. A current address read operation will output data according to the location of the internal data word address counter. This is initiated with a Start condition, followed by a valid device address byte with the R/W bit set to logic `1'. The device will ACK this sequence and the current address data word is serially clocked out on the SDA line. All types of read operations will be terminated if the bus master does not respond with an ACK (it NACKs) during the ninth clock cycle. After the NACK response, the master may send a Stop condition to complete the protocol, or it can send a Start condition to begin the next sequence. Figure 8-1.Current Address Read 1 SCL 2 3 4 5 6 7 8 9 1 2 Device Address Byte SDA 1 1 0 A2 A1 4 5 6 7 8 9 D2 D1 D0 1 Data Word (n) A16 1 0 MSB Start by Master 8.2 0 3 D7 D6 D5 D4 D3 MSB ACK from Slave NACK from Master Stop by Master Random Read A random read begins in the same way as a byte write operation does to load in a new data word address. This is known as a "dummy write" sequence; however, the data byte and the Stop condition of the byte write must be omitted to prevent the part from entering an internal write cycle. Once the device address and word address are clocked in and acknowledged by the EEPROM, the bus master must generate another Start condition. The bus master now initiates a current address read by sending a Start condition, followed by a valid device address byte with the R/W bit set to logic `1'. The EEPROM will ACK the device address and serially clock out the data word on the SDA line. All types of read operations will be terminated if the bus master does not respond with an ACK (it NACKs) during the ninth clock cycle. After the NACK response, the master may send a Stop condition to complete the protocol, or it can send a Start condition to begin the next sequence. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 21 AT24CM01 Read Operations Figure 8-2.Random Read 1 SCL 2 3 4 5 6 7 8 9 1 2 Device Address Byte SDA 1 0 1 0 A2 A1 3 4 5 6 7 8 9 1 2 First Word Address Byte A16 0 A15 A14 A13 A12 A11 A10 0 MSB 4 5 6 7 8 9 A0 0 Second Word Address Byte A9 A8 0 A7 MSB Start Condition by Master 3 A6 A5 A4 A3 A2 A1 MSB ACK from Slave ACK from Slave ACK from Slave Dummy Write 1 2 3 4 5 6 7 8 9 1 2 3 0 1 0 A2 A16 A1 1 0 D7 MSB 6 7 8 9 D6 D5 D4 D3 D2 D1 D0 1 MSB Start Condition by Master 8.3 5 Data Word (n) Device Address Byte 1 4 Stop Condition NACK from Master by Master ACK from Slave Sequential Read Sequential reads are initiated by either a current address read or a random read. After the bus master receives a data word, it responds with an Acknowledge. As long as the EEPROM receives an ACK, it will continue to increment the word address and serially clock out sequential data words. When the maximum memory address is reached, the data word address will roll-over and the sequential read will continue from the beginning of the memory array. All types of read operations will be terminated if the bus master does not respond with an ACK (it NACKs) during the ninth clock cycle. After the NACK response, the master may send a Stop condition to complete the protocol, or it can send a Start condition to begin the next sequence. Figure 8-3.Sequential Read 1 SCL 2 3 4 5 6 7 8 9 1 2 3 Device Address Byte SDA 1 0 1 0 A2 A1 1 A16 6 7 8 9 0 D7 D6 D5 D4 D3 D2 D1 D0 0 MSB Start by Master ACK from Slave 2 3 4 5 6 7 8 9 1 2 Data Word (n+1) D7 5 Data Word (n) MSB 1 4 D6 D5 D4 D3 D2 ACK from Master 3 4 5 6 7 8 1 2 Data Word (n+2) D1 D0 0 MSB D7 D6 D5 D4 D3 D2 3 4 5 6 7 8 9 D1 D0 1 Data Word (n+x) D1 D0 0 MSB D7 D6 D5 D4 D3 D2 MSB ACK from Master (c) 2019 Microchip Technology Inc. 9 ACK from Master Datasheet NACK from Master Stop by Master 20006170A-page 22 AT24CM01 Device Default Condition from Microchip 9. Device Default Condition from Microchip The AT24CM01 is delivered with the EEPROM array set to logic `1', resulting in FFh data in all locations. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 23 AT24CM01 Packaging Information 10. Packaging Information 10.1 Package Marking Information AT24CM01: Package Marking Information 8-lead SOIJ 8-lead SOIC ATMLHYWW ###% CO YYWWNNN ATMLHYWW ###% CO YYWWNNN 8-lead TSSOP 8-ball WLCSP ATHYWW ###%CO YYWWNNN Note 1: %U ### NNN designates pin 1 Note 2: Package drawings are not to scale Catalog Number Truncation AT24CM01 Truncation Code ###: 2G Date Codes Y = Year 4: 2014 5: 2015 6: 2016 7: 2017 Voltages 8: 2018 9: 2019 0: 2020 1: 2021 M = Month A: January B: February ... L: December WW = Work Week of Assembly 02: Week 2 04: Week 4 ... 52: Week 52 Country of Assembly Device Grade CO = Country of Origin H or U: Industrial Grade % = Minimum Voltage D: 2.5V min M: 1.7V min Atmel Truncation AT: Atmel ATM: Atmel ATML: Atmel Lot Number or Trace Code NNN = Alphanumeric Trace Code (2 Characters for Small Packages) (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 24 AT24CM01 Packaging Information 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 2X 0.10 C A-B D A D NOTE 5 N E 2 E1 2 E1 E NOTE 1 2 1 e B NX b 0.25 C A-B D NOTE 5 TOP VIEW 0.10 C C A A2 SEATING PLANE 8X A1 SIDE VIEW 0.10 C h R0.13 h R0.13 H 0.23 L SEE VIEW C (L1) VIEW A-A VIEW C Microchip Technology Drawing No. C04-057-SN Rev D Sheet 1 of 2 (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 25 AT24CM01 Packaging Information 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm (.150 In.) Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Units Dimension Limits Number of Pins N e Pitch Overall Height A Molded Package Thickness A2 Standoff A1 Overall Width E Molded Package Width E1 Overall Length D Chamfer (Optional) h Foot Length L L1 Footprint Foot Angle c Lead Thickness b Lead Width Mold Draft Angle Top Mold Draft Angle Bottom MIN 1.25 0.10 0.25 0.40 0 0.17 0.31 5 5 MILLIMETERS NOM 8 1.27 BSC 6.00 BSC 3.90 BSC 4.90 BSC 1.04 REF - MAX 1.75 0.25 0.50 1.27 8 0.25 0.51 15 15 Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Significant Characteristic 3. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. 5. Datums A & B to be determined at Datum H. Microchip Technology Drawing No. C04-057-SN Rev D Sheet 2 of 2 (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 26 AT24CM01 Packaging Information 8-Lead Plastic Small Outline (SN) - Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging SILK SCREEN C Y1 X1 E RECOMMENDED LAND PATTERN Units Dimension Limits E Contact Pitch Contact Pad Spacing C Contact Pad Width (X8) X1 Contact Pad Length (X8) Y1 MIN MILLIMETERS NOM 1.27 BSC 5.40 MAX 0.60 1.55 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing C04-2057-SN Rev B (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 27 AT24CM01 Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 28 AT24CM01 Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 29 AT24CM01 Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 30 AT24CM01 Packaging Information /HDG3ODVWLF7KLQ6KULQN6PDOO2XWOLQH67 PP%RG\>76623@ 1RWH )RUWKHPRVWFXUUHQWSDFNDJHGUDZLQJVSOHDVHVHHWKH0LFURFKLS3DFNDJLQJ6SHFLILFDWLRQORFDWHGDW KWWSZZZPLFURFKLSFRPSDFNDJLQJ D N E E1 NOTE 1 1 2 b e c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c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 31 AT24CM01 Packaging Information Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging (c) 2017 Microchip Technology Incorporated (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 32 AT24CM01 Packaging Information d 0.015 C 4X d 0.075 C A C D Pin 1 A B C D j n 0.015 m C j n 0.05 m C A B A1 E Ob E C D B A Pin 1 1 1 E 2 2 e 3 3 A2 e2 d2 d A TOP VIEW SIDE VIEW BALL SIDE * Dimensions are NOT to scale. COMMON DIMENSIONS (Unit of Measure = mm) MIN TYP A 0.460 0.499 0.538 A1 0.164 - 0.224 0.280 0.305 0.330 SYMBOL Pin Assignment Matrix A 1 VCC C D SDA E A2 NC WP SCL 2 3 B A1 A2 GND MAX E Contact Microchip for details e 0.866 e2 0.500 d 1.000 d2 0.500 D b NOTE Contact Sales for details 0.239 0.269 0.299 4/25/13 TITLE 8U-6, 8-ball (3x5 Array) Wafer Level Chip Scale Package (WLCSP) GPC DRAWING NO. REV. GHZ 8U-6 B Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 33 AT24CM01 Revision History 11. Revision History Revision A (March 2019) Updated to Microchip template. Microchip DS20006170 replaces Atmel document 8812. Corrected tLOW typo from 400 ns to 500 ns. Corrected tAA typo from 550 ns to 450 ns. Updated Part Marking Information. Updated the "Software Reset" section. Added ESD rating. Removed lead finish designation. Updated trace code format in package markings. Updated section content throughout for clarification. Added a figure for "System Configuration Using Two-Wire Serial EEPROMs". Added POR recommendations section. Updated SOIC, SOIJ and TSSOP package drawings to Microchip format. Atmel Document 8812 Revision F (January 2015) Updated the ordering information section, part markings, and the 8X and 8S2 package outline drawings. Atmel Document 8812 Revision E (March 2013) Updated document status from preliminary to complete. Correctd WLCSP pinout. Updated footers and disclaimer page. Atmel Document 8812 Revision D (January 2013) Corrected TSSOP pin label 7 to WP. Atmel Document 8812 Revision C (December 2012) Added WLCSP package. Updated part markings. Updated pinout diagram. Updated part markings. Corrected Byte Write figure from second typo error to first word address. Updated Sequential Read figure. Atmel Document 8812 Revision B (July 2012) Corrected ordering code: AT24CM01-WWU-11, Die Sale to AT24CM01-WWU11M, Wafer Sale. Updated Atmel logos and disclaimer page. Atmel Document 8812 Revision A (May 2012) Initial release of this document. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 34 AT24CM01 The Microchip Web Site Microchip provides online support via our web site at http://www.microchip.com/. This web site is used as a means to make files and information easily available to customers. Accessible by using your favorite Internet browser, the web site contains the following information: * Product Support - Data sheets and errata, application notes and sample programs, design resources, user's guides and hardware support documents, latest software releases and archived software * General Technical Support - Frequently Asked Questions (FAQ), technical support requests, online discussion groups, Microchip consultant program member listing * Business of Microchip - Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives Customer Change Notification Service Microchip's customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at http://www.microchip.com/. Under "Support", click on "Customer Change Notification" and follow the registration instructions. Customer Support Users of Microchip products can receive assistance through several channels: * * * * Distributor or Representative Local Sales Office Field Application Engineer (FAE) Technical Support Customers should contact their distributor, representative or Field Application Engineer (FAE) for support. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http://www.microchip.com/support (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 35 AT24CM01 Product Identification System To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. AT 24CM 01 - SSHD-B Shipping Carrier Option B = Bulk (Tubes) T = Tape and Reel, Standard Quantity Option E = Tape and Reel, Extended Quantity Option Product Family Operating Voltage 24C = Standard I2C-compatible Serial EEPROM D = 2.5V to 5.5V M = 1.7V to 5.5V Device Grade or Wafer/Die Thickness Device Density M = Megabit Family 01 = 1 Megabit H or U = Industrial Temperature Range (-40C to +85C) 11 = 11mil Wafer Thickness Package Option SS S X U = SOIC = SOIJ = TSSOP = WLCSP Examples Device Package Package Drawing Code Package Option Voltage Shipping Carrier Option Device Grade AT24CM01SSHDB SOIC SN SS 2.5V to 5.5V Bulk (Tubes) AT24CM01SHMT SOIJ SM SS 1.7V to 5.5V Tape and Reel Industrial Temperature (-40C to 85C) AT24CM01XHMB TSSOP ST X 1.7V to 5.5V Bulk (Tubes) AT24CM01UUMT WLCSP 8U-6 U 1.7V to 5.5V Tape and Reel Microchip Devices Code Protection Feature Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 36 AT24CM01 * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Legal Notice Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BitCloud, chipKIT, chipKIT logo, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KeeLoq, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, CodeGuard, CryptoAuthentication, CryptoAutomotive, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, INICnet, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, memBrain, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PowerSmart, PureSilicon, QMatrix, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 37 AT24CM01 All other trademarks mentioned herein are property of their respective companies. (c) 2019, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. ISBN: 978-1-5224-4284-4 AMBA, Arm, Arm7, Arm7TDMI, Arm9, Arm11, Artisan, big.LITTLE, Cordio, CoreLink, CoreSight, Cortex, DesignStart, DynamIQ, Jazelle, Keil, Mali, Mbed, Mbed Enabled, NEON, POP, RealView, SecurCore, Socrates, Thumb, TrustZone, ULINK, ULINK2, ULINK-ME, ULINK-PLUS, ULINKpro, Vision, Versatile are trademarks or registered trademarks of Arm Limited (or its subsidiaries) in the US and/or elsewhere. Quality Management System Certified by DNV ISO/TS 16949 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California (R) (R) and India. The Company's quality system processes and procedures are for its PIC MCUs and dsPIC (R) DSCs, KEELOQ code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 38 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 Australia - Sydney Tel: 61-2-9868-6733 China - Beijing Tel: 86-10-8569-7000 China - Chengdu Tel: 86-28-8665-5511 China - Chongqing Tel: 86-23-8980-9588 China - Dongguan Tel: 86-769-8702-9880 China - Guangzhou Tel: 86-20-8755-8029 China - Hangzhou Tel: 86-571-8792-8115 China - Hong Kong SAR Tel: 852-2943-5100 China - Nanjing Tel: 86-25-8473-2460 China - Qingdao Tel: 86-532-8502-7355 China - Shanghai Tel: 86-21-3326-8000 China - Shenyang Tel: 86-24-2334-2829 China - Shenzhen Tel: 86-755-8864-2200 China - Suzhou Tel: 86-186-6233-1526 China - Wuhan Tel: 86-27-5980-5300 China - Xian Tel: 86-29-8833-7252 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 India - Bangalore Tel: 91-80-3090-4444 India - New Delhi Tel: 91-11-4160-8631 India - Pune Tel: 91-20-4121-0141 Japan - Osaka Tel: 81-6-6152-7160 Japan - Tokyo Tel: 81-3-6880- 3770 Korea - Daegu Tel: 82-53-744-4301 Korea - Seoul Tel: 82-2-554-7200 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 Malaysia - Penang Tel: 60-4-227-8870 Philippines - Manila Tel: 63-2-634-9065 Singapore Tel: 65-6334-8870 Taiwan - Hsin Chu Tel: 886-3-577-8366 Taiwan - Kaohsiung Tel: 886-7-213-7830 Taiwan - Taipei Tel: 886-2-2508-8600 Thailand - Bangkok Tel: 66-2-694-1351 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 Finland - Espoo Tel: 358-9-4520-820 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Israel - Ra'anana Tel: 972-9-744-7705 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-72884388 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 (c) 2019 Microchip Technology Inc. Datasheet 20006170A-page 39