Motor Lead Pigtail Splice for 1000 volts (or less) cables with one-hole lugs Instructions Kit Contents (kit contains 3 splices): 3 Lug Covers 3 Tubes Silicone Grease 3 Mastic Sealing Strips Kit Selection Table Kit Number Cable Size Range AWG (mm2) Feeder Motor Lead Cable Insulation O.D. Range in. (mm) Lug Cover* I.D. in. (mm) Maximum Bolt Length in. (mm) 5300 14 - 10 (2,5 - 4) 16 -12 (1,5 - 2,5) 0.12 - 0.21 (3 - 5) 0.45 (11) 3/8 (10) 5301 10 - 4 (6 - 16) 12 - 4 (4 - 16) 0.17 - 0.36 (4 - 9) 0.70 (18) 1/2 (13) * Lug cover I.D. - use when calculating kit sizing for a connection of more than two conductors (e.g. 3-way, 4-way, etc. Use of one-hole stacking lugs is recommended.) Table 1 Technical Information: For use on Non-Shielded Cables 1000 Volts (or less) with one-hole lugs. Cable Size Range: Feeder: 14 AWG-4 AWG Motor Lead: 16 AWG-4 AWG Copper Conductors 3MTM Motor Lead Pigtail Splice Kits CAUTION for 1000 Volts (or less) Working around energized high-voltage systems may cause serious injury or death. Installation should be performed by personnel familiar with good safety practice in handling high-voltage electrical equipment. De-energize and ground all electrical systems before installing product. 5300, 5301 78-8126-0998-6-A B. Install Lugs A. Prepare Cables According to Standard Procedures 1. Install and crimp lugs per manufacturer's direction. (See back page if 3M lugs are used.) 1. Check to be sure cable sizes fit within the kit range as shown in Table 1. 2. Clean insulation (or jacket as applicable) for approximately 6" (152 mm). 2. Remove cable insulation for length recommended by terminal lug manufacturer; if no information is available, remove for depth of lug barrel. Note: 3. Bolt lugs together. See Table 1 for maximum bolt length, and Figure 1 for proper bolt/lug arrangement. If a split bolt connector is used, refer to Table 2 below for maximum split bolt size for each kit. Kit No. Max. Split Bolt Size 5300 10 AWG 5301 8 AWG C. Installation Note: If moisture resistance is not required, proceed to Step 4. 1. To gauge mastic build up in next step, temporarily install lug cover over bolted lugs, leaving 1/2" (13 mm) of lug exposed. Table 2 2. Separate the cables and apply mastic strip around insulation and between them at a position just onto insulation (Figure 3). For jacketed feeder cable, see note below. Build thickness so the overall diameter is slightly larger than the observed inside diameter of the lug cover. Press cables together and be sure that no void exists between them. MASTIC STRIP OVERWRAPPED WITH VINYL TAPE LUG COVER Figure 1 For Jacketed Feeder Cable Only: If jacketed feeder cable is used, remove an additional 1/4" (6 mm) of jacket, leaving 1/4" (6 mm) of cable insulation exposed (Figure 2). Jacket " APPLY SILICONE GREASE Figure 3 For Jacketed Feeder Cable Only: Insulation For jacketed feeder cable, center mastic strip over cutback edge of cable jacket, so that it seals onto both the cable jacket and insulation (Figure 4). JACKET EDGE INSULATION LUG COVER Figure 2 MASTIC STRIP OVERWRAPPED WITH VINYL TAPE APPLY SILICONE GREASE Figure 4 2 78-8126-0998-6-A 3. Overwrap the mastic with 1 or 2 wraps of vinyl tape. 4. Install lug cover. Note: The kit contains a small tube of silicone grease. Use it to lightly lubricate the mastic-vinyl wrap. This will aid in installing the lug cover (Figure 3 or 4, as applicable). 5. Overwrap the end of the lug cover and onto the cables with 1 or 2 wraps of vinyl tape (Figure 5). LUG COVER VINYL TAPE Figure 5 Lug and Crimping Information for ScotchlokTM Copper Lugs 30014 thru 30021 One hole 5.0 Copper Lugs 78-8126-0998-6-A 3 Appendix A Appendix B Splice Removal Splice Reusability 1. Remove Vinyl Tape from end of Lug Cover. (Avoid use of knife or other sharp tools that could damage cables.) 1. First inspect the removed Lug Cover for damage or wear. Replace it with a new splice if evidence of damage or wear is found. 2. Slide Lug Cover off of lugged or split-bolt connection. 3. If splice was sealed for moisture resistance: Remove Mastic and Vinyl Tape Seal from cables. (CAUTION: Be careful not to damage cables.) 4. Remove nut and bolt (or split-bolt) to separate the motor lead from the feeder cable(s). 2. Obtain material to replace the non-reusable splice components. 3. Re-Install the splice according to the standard kit instructions. Reusable Component * Lug Cover Replacement Components These are standard 3M products, available from 3M Electrical Products Division. * Scotch-SealTM 2230 Mastic Strip (UPC 05400741813), 5/8" x 6", 40/case * 3MTM SIL-5cc Silicone Grease (UPC 054007-41814), 5 cc Tube * Scotch(R) Super 33+ Vinyl Electrical Tape (UPC 054007-06132), 3/4" x 66' * 3MTM Pin-Lug Cover, 2" Lg. (78-8041-7208-4, special order) 3M, Scotch and Scotchlok are trademarks of 3M. IMPORTANT NOTICE Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture as of the date of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential regardless of the legal theory asserted. Electrical Products Division 6801 River Place Blvd. Austin, TX 78726-9000 www.3M.com/elpd Printed on 50% recycled paper with 10% post-consumer Litho in USA (c)3M 2002 78-8126-0998-6-A