Technical Data
8845A/8846A
Digital Multimeters
accessory guide
Test leads, probes, and probe tips
TL71 Premium Test Lead Set
Included with 8845A
and 8846A
One pair (red, black)
comfort grip probes
with silicone insu-
lated, right-angle test
leads
Probe tip size: 2 mm
Recommended for µV
measurements
CAT IV 600 V, CAT III
1000 V, 10 A rating. UL listed.
One-year warranty
TL910 Precision Electronic Probe Set
Very small 1 mm
tips to access hard-
to-reach test points
Probe tip length up
to 100 mm, test lead
length: 1 m
Included : 3 sets of
spring loaded gold
tips and 2 sets of
stainless steel tips
CAT IV 600 V, CAT III
1000 V, 3 A rating
One-year warranty
Introduction
The 8845A/8846A Digital Multimeters are complemented
by a comprehensive range of accessories, all of which are
designed to help you get the most from your multimeter. This
data sheet explains in more detail the makeup of key acces-
sories and offers technical specifications where required.
TL80A Basic Electronic DMM Test Set
One pair (red, black) each 1 meter
long silicone test lead set, alligator
clip and probe tip extender
Probe tip size: 2 mm
C75 soft carrying case
CAT II 300 V. UL listed.
One-year warranty
8845A-TPIT Test Probe IC Tip Set
One pair (red and black)
Snaps onto DMM probes with
.080 in (2 mm) O.D. Tips
Designed to IEC 1010 standard
Pin tip jack at the adapter end
is recessed for added insulation
protection
Adapter allows easy access to
leads of through-hole IC’s
Insulation at the tip fits between
leads to prevent accidental shorting
Specifications
Materials Tip: Stainless steel, nickel plated
Body: Polypropylene, fire retardant, UL94 V-2 rated
Color One red, one black
Safety IEC 1010-2-031, Category II, P2 compliant
Operating
voltage
300 V rms/dc
Current 3 A
8845A-EFPT Fine Point Extended Test Probe
Adapter Set
One pair (red
and black)
Snaps onto
DMM probes
with .080 in
(2 mm) O.D.
Tips
Designed to
IEC 1010 standard
Adapter allows access to hard-to-reach test
points
Tips are insulated to the point to prevent short-
ing of adjacent components
Specifications
Materials Tip: Stainless steel Tip insulation:
Kynar Body: Polypropylene, fire
retardant, UL94 V-2 rated
Color One red, one black
Safety IEC 1010-2-031, Category II, P2
compliant
Operating
voltage
300 V rms/dc
Current 3 A
TL2X4W-PTII 2X4 Wire Ohms Test Lead
Perform 4-
wire measure-
ments with
only two test
leads
Two conduc-
tors per lead
(one source
and one
measure)
Excellent resolution and accuracy
Specifications
Maximum voltage between test lead and ground:
1000 V
Maximum transient overvoltage and input voltage
combined: 1000 V
Maximum current: 500 mA
Temperature Operating: 0 to 55 °C < 90 %
relative humidity
Storage: -40° C to 170 °C
Altitude 2000 m
Safety Complies with EN/IED 61010-031
and CAN/CSA C22.2 No. 61010-1-
04 for Measurement Category 1
1000 V
Test leads, probes, and probe tips cont.
884X-Short 4-wire short
4-terminal shorting bar
4 mm banana terminals
sized and orientated to
short DMM input source and
sense terminals
Used to null out front end
offsets or as required by the
calibration procedure
884x-RTD 100 Ohm RTD
Temperature Probe
Manufactured using a
coil suspension element
design for increased
shock and vibration
resistance
Mineral-insulated
sheath with a minimum
bend radius of 19 mm
(3/4 in) for flexibility
and durability
Specifications
Resistance Nominal 100 Ω
Temperature coefficient 0.00385 Ω/Ω °C nominal
Temperature range -200 °C to 300 °C (transition and cable
temperature: 0 °C to 150 °C)
Drift rate + 0.13 °C at 0 °C after 1000 hours at
300 °C
Sheath material 316 stainless steel
Leads Teflon-insulated, nickel-plated stranded
copper, 22 AWG
Termination 4-wire banana
Time constant Four seconds maximum for 63.2 %
response to step change in water moving
at 3 fps
Bending radius 19 mm (3/4 in) except for 50 mm (2 in)
area of sheath near tip
Calibration Includes manufacturer’s NIST-traceable
calibration and table with R vs. T values
in 1 °C increments from -196 °C to 300 °C.
Callendar – van Dusen coefficients
included
Immersion At least 100 mm (4 in) recommended
Accuracy (includes cali-
bration uncertainty and
short-term stability)
± 0.050 °C at -196 °C
± 0.050 °C at 0 °C
± 0.051 °C at 200 °C
± 0.055 °C at 300 °C
Size 9 in L x 3/16 in diameter
Marking Each RTD is marked with the Fluke name
and part number
884X-USB USB to RS-232 Cable Adapter
USB to serial
RS-232 inter-
face adapter
cable
Converts from
standard DB
9-pin serial to
USB 2.0
Requires an
available PC
communications port
1.65 m cable length
Includes cable and USB driver disk (CD-ROM)
884X-ETH Ethernet
Interface Cable
8-conductor (4
twisted pair)
unshielded cable
(48 inches) with
an 8-position
modular plug
(RJ45) on each
end, with an overmold boot/strain relief
Rated working voltage: 100 V rms max.
Operating temperature range: -40 °C to + 80 °C
884X-512M 12 Mbyte memory
Used on the 8846A
only
Plugs into USB
device host port
on the 8846A front
panel
Fully compliant with
Universal Serial Bus
Specification v2.0
Dual LED indicates power and busy status
884X-1G USBMemory 1 GB
Used on the 8846A only
Plugs into USB device host port on the 8846A
front panel
Fully compliant with Universal Serial Bus
Specification v2.0
Dual LED indicates power and busy status
Memory
Interface cables
RS43 RS-232 cable
RS43, 2 m
DB9-to-DB9 for PC to unit
Y8021 and Y8022 IEEE-488 cables
Shielded IEEE 488 one-meter (39.4 inches) and
two-meter (78.8 inches) cables, with plug and
jack at each end
Software
FlukeView Forms
Document, store and analyze individual
readings or series of measurements, then
convert them into professional-looking
documents
FlukeView Forms Basic, included with
8845A/8846A, transfers data points from
the meter to a PC, displays readings in
table or graphical form
For a larger array of forms, or to use
FlukeView® Forms Designer to customize
your forms, upgrade to FlukeView® Forms
version 3.0 with FVF-UG
Model Name Description
FVF-SC5 FlukeView Forms, Basic Software Includes:
CD for FlukeView Forms Basic
Users manual, registration card, and software
license agreement
FVF-UG FlukeView Forms, Software Upgrade – No Cable
Includes:
CD for FlukeView Forms Version 3.0
Users manual, registration card, and software
license agreement
FVF-SC4 Extended FlukeView Forms with USB Cable
Includes:
CD for FlukeView Forms Version 3.0
PC-to-meter serial-to-USB adapter cable
Users manual, registration card, and software
license agreement
FlukeView Forms Requirements
Operating system for
FVF-SC2 and FVF-Basic
Windows 98 Second Edition, Windows
Me, Windows 2000, or Windows XP
Operating system for
FVF-SC1 and FVF-SC3
Windows 95, Windows 98, Windows
Me, Windows NT 4.0, Windows 2000, or
Windows XP
Minimum PC Hardware Pentium class or better microprocessor;
32 MB RAM; 70 MB hard disk space
(100 MB to install); Serial or USB port
Fluke Corporation
PO Box 9090, Everett, WA USA 98206
Fluke Europe B.V.
PO Box 1186, 5602 BD
Eindhoven, The Netherlands
For more information call:
In the U.S.A. (800) 443-5853 or
Fax (425) 446-5116
In Europe/M-East/Africa (31 40) 2 675 200 or
Fax (31 40) 2 675 222
In Canada (800)-36-FLUKE or
Fax (905) 890-6866
From other countries +1 (425) 446-5500 or
Fax +1 (425) 446-5116
Web access: http://www.fluke.com
©2007 Fluke Corporation. All rights reserved.
Information subject to change without notice.
Printed in U.S.A. 4/2007 2815866 D-EN-N Rev B
Pub_ID: 11205-eng Rev 02
Fluke. Keeping your world
up and running.®
884X-CASE
Tough molded
plastic case with
die cut foam to
hold and protect
the 8845A or
8846A meter
Accessories and
manual compart-
ments
One-year warranty
Rack Mount Kit
Y8846S allows
meter to be
mounted in a
standard 19-
inch rack
Y8846D
enables
mounting two
meters side-
by-side in a
standard 19-inch rack
Parts list
Quantity Description
Y8846S Y8846D
1 2 Small filler plate
1 NA Large filler plate
1 NA Large filler plate bracket
1 1 Rack mount tray
NA 1 Dual center mount
2 2 #8-32 x 1/2 in panhead Philips screws
1 2 #6-32 x 1/4 in panhead Philips screws
4 4 #10-32 x 3/4 in Philips rack screws
1 2 #6-32 x 1/2 in panhead Philips screws
4 4 #10-32 rack nuts
Other accessories
Traceable calibration with data
Traceable calibration without data
Accredited calibration
Repair services
Extended warranty agreements
Calibration and repair coverage services
Product upgrades
*Contact your local Fluke service center for details and
availability
Calibration and Service
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Fluke:
TL2X4W-PTII 8845A-TPIT 884X-1G 884X-512M 884X-CASE 884X-ETH 884X-RTD 884X-SHORT RS43
Y8846D Y8846S