CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper I.C. Handling Procedures.
Copyright © Harris Corporation 1994 1
SEMICONDUCTOR
DG181 thru DG191
High-Speed Drivers with JFET Switch
Description
The DG181 thru DG191 series of analog gates consist of 2
or 4 N-channel junction-type field-effect transistors (JFET)
designed to function as electronic switches. Level-shifting
drivers enable low-level inputs (0.8V to 2V) to control the
ON-OFF state of each switch. The driver is designed to
provide a turn-off speed which is faster than turn-on speed,
so that break-before-make action is achieved when
switching from one channel to another. In the ON state, each
switch conducts current equally well in both directions. In the
OFF condition, the switches will block voltages up to 20V
peak-to-peak. Switch-OFF input-output isolation 50dB at
10MHz, due to the low output impedance of the FET-gate
driving circuit.
Features
Constant ON-Resistance for Signals to ±10V (DG182,
DG185, DG188, DG191), to ±7.5V (All Devices)
±15V Power Supplies
<2nA Leakage from Signal Channel in Both ON and
OFF States
TTL, DTL, RTL Direct Drive Compatibility
•t
ON, tOFF <150ns, Break-Before-Make Action
Cross-Talk and Open Switch Isolation >50dB at 10MHz
(75 Load)
File Number 3114.1
December 1994
Functional Diagrams (Typical Channel)
DG186, DG187, DG188 - ONE AND TWO CHANNEL
SPDT AND SPST CIRCUIT CONFIGURATION DG183, DG184, DG185 - TWO CHANNEL DPST
CIRCUIT CONFIGURATION
S2
D2
S1
D1
V+
GND
VL
IN
V-
S
D
S
D
V+
GND
VL
IN
V-
2
DG181 Series
Ordering Information
PART NUMBER TYPE RDS(ON)
(MAX) PACKAGE
DG181AA Dual SPST 3010 Lead CAN
DG181AA/883B Dual SPST 3010 Lead CAN
DG181AP Dual SPST 3014 Lead SBDIP
DG181AP/883B Dual SPST 3014 Lead SBDIP
DG181BA Dual SPST 3010 Lead CAN
DG181BP Dual SPST 3014 Lead SBDIP
DG182AA Dual SPST 7510 Lead CAN
DG182AA/883B Dual SPST 7510 Lead CAN
DG182AP Dual SPST 7514 Lead SBDIP
DG182AP/883B Dual SPST 7514 Lead SBDIP
DG182BA Dual SPST 7510 Lead CAN
DG182BP Dual SPST 7514 Lead SBDIP
DG184AP Dual DPST 3016 Lead SBDIP
DG184AP/883B Dual DPST 3016 Lead SBDIP
DG184BP Dual DPST 3016 Lead SBDIP
DG185AP Dual DPST 7516 Lead SBDIP
DG185AP/883B Dual DPST 7516 Lead SBDIP
DG185BP Dual DPST 7516 Lead SBDIP
DG187AA SPDT 3010 Lead CAN
DG187AA/883B SPDT 3010 Lead CAN
DG187AP SPDT 3014 Lead SBDIP
DG187AP/883B SPDT 3014 Lead SBDIP
DG187BA SPDT 3010 Lead CAN
DG187BP SPDT 3014 Lead SBDIP
DG188AA SPDT 7510 Lead CAN
DG188AA/883B SPDT 7510 Lead CAN
DG188AP SPDT 7514 Lead SBDIP
DG188AP/883B SPDT 7514 Lead SBDIP
DG188BA SPDT 7510 Lead CAN
DG188BP SPDT 7514 Lead SBDIP
DG190AP Dual SPDT 3016 Lead SBDIP
DG190AP/883B Dual SPDT 3016 Lead SBDIP
DG190BP Dual SPDT 3016 Lead SBDIP
DG191AP Dual SPDT 7516 Lead SBDIP
DG191AP/883B Dual SPDT 7516 Lead SBDIP
DG191BP Dual SPDT 7516 Lead SBDIP
Ordering Information
(Continued)
PART NUMBER TYPE RDS(ON)
(MAX) PACKAGE
3
DG181 Series
Pinouts and Switching State Diagrams
DUAL SPST - DG181, DG182
(TO-100 METAL CAN)
TOP VIEW
DUAL SPST - DG181, DG182
(CDIP)
TOP VIEW
DUAL DPST - DG184, DG185
(CDIP)
TOP VIEW
SPDT - DG187, DG188
(TO-100 METAL CAN)
TOP VIEW
SPDT - DG187, DG188
(CDIP)
TOP VIEW
DUAL SPDT - DG190, DG191
(CDIP)
TOP VIEW
IN2
VL
V+
D12
5
1
3
10
4
8
9
7
6
D2
V-
GND
IN1
S1
S2S1
D1
NC
NC
IN1
V+
VL
S2
D2
NC
NC
IN2
V-
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
D1
NC
D3
S3
S4
D4
D2
NC
S1
V-
GND
VL
V+
IN2
S2
IN1
2
5
1
3
10
4
8
9
7
6
S2
V-
GND
IN
D1
D2
NC
VL
V+
S1
NC
NC
IN
V+
VL
NC
NC
D2
S2
NC
V-
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
D1
S1
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
D1
NC
D3
S3
S4
D4
D2
NC
S1
V-
GND
VL
V+
IN2
S2
IN1
4
Specifications DG181 Series
Absolute Maximum Ratings Thermal Information
V+ - V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V
V+ - VD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V
VD - V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33V
VD - VS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±22V
VL - V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36V
VL - VIN, VL - GND, VIN - GND . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V
GND - V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27V
GND - VIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V
Current (S or D) (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . .200mA
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65oC to +150oC
Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . +300oC
Operating Temperature. . . . . . . . . . . . . . . . . . . . . .-55oC to +125oC
Maximum Power Dissipation †
TO Metal Can Packages . . . . . . . . . . . . . . . . . . . . . . . . . . 450mW
Derate 6mW/oC above +75oC
Ceramic DIP Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . 825mW
Derate 11mW/oC above +75oC
† Device mounted with all leads welded or soldered to PC board.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications V+ = +15V, V- = -15V, VL = 5V, Unless Otherwise Specified
PARAMETER DEVICE
NUMBER (NOTE 1)
TEST CONDITIONS
A SERIES B SERIES
UNITS-55oC +25oC +125oC -20oC +25oC +85oC
SWITCH
IS(OFF) DG181, DG182,
DG184, DG185,
DG187, DG188,
DG190, DG191
VS = 10V, VD = -10V,
V+ = 10V, V- = -20V,
VIN = “OFF”
-±1 100 - ±5 100 nA
DG181, DG184,
DG187, DG190 VS = 7.5V, VD = -7.5V,
VIN = “OFF” -±1 100 - ±5 100 nA
DG182, DG185,
DG188, DG191 VS = 10V, VD = -10V,
VIN = “OFF” -±1 100 - ±5 100 nA
ID(OFF) DG181, DG182,
DG184, DG185,
DG187, DG188,
DG190, DG191
VS = 10V, VD = -10V,
V+ = 10V, V- = -20V,
VIN = “OFF”
-±1 100 - ±5 100 nA
DG181, DG184,
DG187, DG190 VS = 7.5V, VD = -7.5V,
VIN = “OFF” -±1 100 - ±5 100 nA
DG182, DG185,
DG188, DG191 VS = 10V, VD = -10V,
VIN = “OFF” -±1 100 - ±5 100 nA
ID(ON) + IS(ON) DG181, DG184,
DG187, DG190 VD = VS = -7.5V, VIN = “ON” - ±2 -200 - -10 -200 nA
DG182, DG185,
DG188, DG191 VD = VS = -10V, VIN = “ON” - ±2 -200 - -10 -200 nA
INPUT
IINL All VIN = 0V -250 -250 -250 -250 -250 -250 µA
IINH All VIN = 5V - 10 20 - 10 20 µA
DYNAMIC
tON 30 Switches See Switching Time
Test Circuit - 150 - - 180 - ns
75 Switches - 250 - - 300 - ns
tOFF 30 and 75
Switches - 130 - - 150 - ns
CS(OFF) DG181, DG182,
DG184, DG185,
DG187, DG188,
DG190, DG191
VS = -5V, ID = 0, f = 1MHz 9 Typical pF
VD = +5V, IS = 0, f = 1MHz 6 Typical pF
CD(ON) +
CS(ON)
VD = VS = 0, f = 1MHz 14 Typical pF
OFF Isolation RL = 75, CL = 3pF Typically >50dB at 10MHz -
5
Specifications DG181 Series
SUPPLY
I+ DG181, DG182,
DG190, DG191 VIN = 5V - 1.5 - - 1.5 - mA
DG184, DG185 - 0.1 - - 0.1 - mA
DG187, DG188 - 0.8 - - 0.8 - mA
I- DG181, DG182,
DG190, DG191 - -5.0 - - -5.0 - mA
DG184, DG185 - -4.0 - - -4.0 - mA
DG187, DG188 - -3.0 - - -3.0 - mA
ILDG181, DG182,
DG184, DG185,
DG190, DG191
- 4.5 - - 4.5 - mA
DG187, DG188 - 3.2 - - 3.2 - mA
IGND All - -2.0 - - -2.0 - mA
I+ DG181, DG182,
DG190, DG191 VIN = 0V - 1.5 - - 1.5 - mA
DG184, DG185 - 3.0 - - 3.0 - mA
DG187, DG188 - 0.8 - - 0.8 - mA
I- DG181, DG182,
DG190, DG191 - -5.0 - - -5.0 - mA
DG184, DG185 - -5.5 - - -5.5 - mA
DG187, DG188 - -3.0 - - -3.0 - mA
ILDG181, DG182,
DG184, DG185,
DG190, DG191
- 4.5 - - 4.5 - mA
DG187, DG188 - 3.2 - - 3.2 - mA
IGND All - -2.0 - - -2.0 - mA
NOTE:
1. See Switching State Diagrams for VIN “ON” and VIN “OFF” Test Conditions.
Electrical Specifications Maximum Resistances (RDS(ON) MAX)
DEVICE
NUMBER TEST CONDITIONS (NOTE 1)
V+ = 15V, V- = -15V, VL = 5V
MILITARY
TEMPERATURE INDUSTRIAL
TEMPERATURE
UNITS-55oC +25oC +125oC -20oC +25oC +85oC
DG181 VD = -7.5V IS = -10mA, VIN = “ON” 30 30 60 50 50 75
DG182 VD = -10V 75 75 100 100 100 150
DG184 VD = -7.5V 30 30 60 50 50 75
DG185 VD = -10V 75 75 150 100 100 150
DG187 VD = -7.5V 30 30 60 50 50 75
DG188 VD = -10V 75 75 150 100 100 150
DG190 VD = -7.5V 30 30 60 50 50 75
DG191 VD = -10V 75 75 150 100 100 150
NOTES:
1. See Switching State Diagrams for VIN “ON” and VIN “OFF” Test Conditions.
2. Normally the minimum signal handling capability of the DG181 thru DG191 family is 20V peak to peak for the 75 switches and 15V peak-
to-peak for the 30 (refer ID and IS tests above).
3. For other Analog Signals, the following guidelines can be used: proper switch turn-off requires that V- VANALOG(peak) - VP where VP =
7.5V for the 80 switches and VP = 5.0V for 75 switches e.g., - 10V minimum (-peak) analog signal and a 75 switch (VP = 5V), requires
that V- -10V -5V = -15V.
Electrical Specifications V+ = +15V, V- = -15V, VL = 5V, Unless Otherwise Specified (Continued)
PARAMETER DEVICE
NUMBER (NOTE 1)
TEST CONDITIONS
A SERIES B SERIES
UNITS-55oC +25oC +125oC -20oC +25oC +85oC
6
DG181 Series
DUAL SPST - DG181/182
TEST CONDITIONS
VIN “ON” = 0.8V All Channels
VIN “OFF” = 2.0V All Channels
NOTE:
1. Switch states are for logic “1” input = 2.0V.
SPDT - DG187/188
TEST CONDITIONS
VIN “ON” = 2.0V Channel 1
VIN “ON” = 0.8V Channel 2
VIN “OFF” = 2.0V Channel 2
VIN “OFF” = 0.8V Channel 1
NOTE:
1. Switch states are for logic “1” input = 2.0V.
DUAL DPST - DG184/185
TEST CONDITIONS
VIN “ON” = 2.0V All Channels
VIN “OFF” = 0.8V All Channels
NOTE:
1. Switch states are for logic “1” input = 2.0V.
SPDT - DG190/191
TEST CONDITIONS
VIN “ON” = 2.0V Channel 1 and 2
VIN “ON” = 0.8V Channel 3 and 4
VIN “OFF” = 2.0V Channel 3 and 4
VIN “OFF” = 0.8V Channel 1 and 2
NOTE:
1. Switch states are for logic “1” input = 2.0V.
NOTES:
1. Switch output waveform shown for VS = constant with logic input waveform as shown.
2. VS may be + or - as per switching time test circuit. VO is the steady state output with switch on. Feedthrough via gate capacitance may
result in spikes at leading and trailing edge of output waveform.
Switching Time Test Circuits
FIGURE 1. SWITCHING TIME TEST WAVEFORMS (Note 1) FIGURE 2. SWITCHING TIME TEST CIRCUIT (Note 2)
50%
90%
0V
tOFF
LOGIC
INPUT
SWITCH
OUTPUT
VS
tON
tR < 10ns
tF < 10ns
90%
SWITCH
INPUT
3V
50%
0V
VO
S1
IN1
LOGIC
INPUT
GND
tON, VS = +10V RL
1kCL
30pF
SWITCH
OUTPUT
+15V
VCC
-15VV-
SWITCH
INPUT
0V
(REPEAT TEST FOR
ALL CHANNELS)
VO = VSRL
RL + RDS(ON)
D1
+5V VL
tOFF, VS = -10V
7
DG181 Series
D14.3 MIL-STD-1835 CDIP2-T14 (D-1, CONFIGURATION C)
14 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A - 0.200 - 5.08 -
b 0.014 0.026 0.36 0.66 2
b1 0.014 0.023 0.36 0.58 3
b2 0.045 0.065 1.14 1.65 -
b3 0.023 0.045 0.58 1.14 4
c 0.008 0.018 0.20 0.46 2
c1 0.008 0.015 0.20 0.38 3
D - 0.785 - 19.94 -
E 0.220 0.310 5.59 7.87 -
e 0.100 BSC 2.54 BSC -
eA 0.300 BSC 7.62 BSC -
eA/2 0.150 BSC 3.81 BSC -
L 0.125 0.200 3.18 5.08 -
Q 0.015 0.060 0.38 1.52 5
S1 0.005 - 0.13 - 6
S2 0.005 - 0.13 - 7
α90o105o90o105o-
aaa - 0.015 - 0.38 -
bbb - 0.030 - 0.76 -
ccc - 0.010 - 0.25 -
M - 0.0015 - 0.038 2
N14 148
Rev. 0 4/94
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. Dimension Q shall be measured from the seating plane to the
base plane.
6. Measure dimension S1 at all four corners.
7. Measure dimension S2 from the top of the ceramic body to the
nearest metallization or lead.
8. N is the maximum number of terminal positions.
9. Braze fillets shall be concave.
10. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
11. Controlling dimension: INCH.
bbb C A - B
S
c
Q
L
A
SEATING
BASE
D
PLANE
PLANE
S S
-D-
-A-
-C-
eA
-B-
aaa C A - B
MD
S S
ccc C A - B
MD
S S
D
E
S1
b2 b
A
e
M
c1
b1
(c)
(b)
SECTION A-A
BASE
LEAD FINISH
METAL
eA/2
S2
M
A
Ceramic Dual-In-Line Metal Seal Packages (SBDIP)
8
DG181 Series
D16.3 MIL-STD-1835 CDIP2-T16 (D-2, CONFIGURATION C)
16 LEAD CERAMIC DUAL-IN-LINE METAL SEAL PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A - 0.200 - 5.08 -
b 0.014 0.026 0.36 0.66 2
b1 0.014 0.023 0.36 0.58 3
b2 0.045 0.065 1.14 1.65 -
b3 0.023 0.045 0.58 1.14 4
c 0.008 0.018 0.20 0.46 2
c1 0.008 0.015 0.20 0.38 3
D - 0.840 - 21.34 -
E 0.220 0.310 5.59 7.87 -
e 0.100 BSC 2.54 BSC -
eA 0.300 BSC 7.62 BSC -
eA/2 0.150 BSC 3.81 BSC -
L 0.125 0.200 3.18 5.08 -
Q 0.015 0.060 0.38 1.52 5
S1 0.005 - 0.13 - 6
S2 0.005 - 0.13 - 7
α90o105o90o105o-
aaa - 0.015 - 0.38 -
bbb - 0.030 - 0.76 -
ccc - 0.010 - 0.25 -
M - 0.0015 - 0.038 2
N16 168
Rev. 0 4/94
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark.
2. The maximum limits of lead dimensions b and c or M shall be
measured at the centroid of the finished lead surfaces, when
solder dip or tin plate lead finish is applied.
3. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness.
4. Corner leads (1, N, N/2, and N/2+1) may be configured with a
partial lead paddle. For this configuration dimension b3 replaces
dimension b2.
5. Dimension Q shall be measured from the seating plane to the
base plane.
6. Measure dimension S1 at all four corners.
7. Measure dimension S2 from the top of the ceramic body to the
nearest metallization or lead.
8. N is the maximum number of terminal positions.
9. Braze fillets shall be concave.
10. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
11. Controlling dimension: INCH.
bbb C A - B
S
c
Q
L
A
SEATING
BASE
D
PLANE
PLANE
S S
-D-
-A-
-C-
eA
-B-
aaa C A - B
MD
S S
ccc C A - B
MD
S S
D
E
S1
b2 b
A
e
M
c1
b1
(c)
(b)
SECTION A-A
BASE
LEAD FINISH
METAL
eA/2
S2
M
A
Ceramic Dual-In-Line Metal Seal Packages (SBDIP)
9
Harris Semiconductor products are sold by description only. Harris Semiconductor reserves the right to make changes in circuit design and/or specifications at
any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Harris is
believed to be accurate and reliable. However, no responsibility is assumed by Harris or its subsidiaries for its use; nor for any infringements of patents or other
rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Harris or its subsidiaries.
Sales Office Headquarters
For general information regarding Harris Semiconductor and its products, call 1-800-4-HARRIS
UNITED STATES
Harris Semiconductor
2401 Palm Bay Road N.E.
Palm Bay, Florida 32905
TEL: (407) 724-7000
EUROPE
Harris Semiconductor
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2-724-2111
SOUTH ASIA
Harris Semiconductor H.K. Ltd.
13/F Fourseas Building
208-212 Nathan Road
Tsimshatsui, Kowloon
Hong Kong
TEL: (852) 723-6339
NORTH ASIA
Harris K.K.
Kojimachi-Nakata Bldg. 4F
5-3-5 Kojimachi
Chiyoda-ku, Tokyo 102 Japan
TEL: (81) 3-3265-7571
TEL: (81) 3-3265-7572 (Sales)
SEMICONDUCTOR
DG181 Series
NOTES:
1. (All leads) Øb applies between L1 and L2. Øb1 applies between
L2 and 0.500 from the reference plane. Diameter is uncontrolled
in L1 and beyond 0.500 from the reference plane.
2. Measured from maximum diameter of the product.
3. α is the basic spacing from the centerline of the tab to terminal 1
and βis the basic spacing of each lead or lead position (N -1
places) from α,looking at the bottom of the package.
4. N is the maximum number of terminal positions.
5. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
6. Controlling dimension: INCH.
Øb
ØD2
Øek1
k
β
Øb1
BASE AND
SEATING PLANE
F
Q
ØD ØD1
L1
L2
REFERENCE PLANE
L
A
α
Øb2
Øb1
BASE METAL LEAD FINISH
SECTION A-A
A
A
N
e1
C
L
2
1
T10.B MIL-STD-1835 MACY1-X10 (A2)
10 LEAD METAL CAN PACKAGE
SYMBOL
INCHES MILLIMETERS
NOTESMIN MAX MIN MAX
A 0.165 0.185 4.19 4.70 -
Øb 0.016 0.019 0.41 0.48 1
Øb1 0.016 0.021 0.41 0.53 1
Øb2 0.016 0.024 0.41 0.61 -
ØD 0.335 0.375 8.51 9.52 -
ØD1 0.305 0.335 7.75 8.51 -
ØD2 0.110 0.160 2.79 4.06 -
e 0.230 BSC 5.84 BSC -
e1 0.115 BSC 2.92 BSC -
F - 0.040 - 1.02 -
k 0.027 0.034 0.69 0.86 -
k1 0.027 0.045 0.69 1.14 2
L 0.500 0.750 12.70 19.05 1
L1 - 0.050 - 1.27 1
L2 0.250 - 6.35 - 1
Q 0.010 0.045 0.25 1.14 -
α36o BSC 36o BSC 3
β36o BSC 36o BSC 3
N10 104
Rev. 0 5/18/94
Metal Can Packages (Can)