FLEX 10KE (R) Embedded Programmable Logic Device January 2003, ver. 2.5 Features... Data Sheet f Embedded programmable logic devices (PLDs), providing system-on-a-programmable-chip (SOPC) integration in a single device - Enhanced embedded array for implementing megafunctions such as efficient memory and specialized logic functions - Dual-port capability with up to 16-bit width per embedded array block (EAB) - Logic array for general logic functions High density - 30,000 to 200,000 typical gates (see Tables 1 and 2) - Up to 98,304 RAM bits (4,096 bits per EAB), all of which can be used without reducing logic capacity System-level features - MultiVoltTM I/O pins can drive or be driven by 2.5-V, 3.3-V, or 5.0-V devices - Low power consumption - Bidirectional I/O performance (tSU and tCO) up to 212 MHz - Fully compliant with the PCI Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2 for 3.3-V operation at 33 MHz or 66 MHz - -1 speed grade devices are compliant with PCI Local Bus Specification, Revision 2.2, for 5.0-V operation - Built-in Joint Test Action Group (JTAG) boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990, available without consuming additional device logic For information on 5.0-V FLEX(R) 10K or 3.3-V FLEX 10KA devices, see the FLEX 10K Embedded Programmable Logic Family Data Sheet. Table 1. FLEX 10KE Device Features Feature EPF10K30E EPF10K50E EPF10K50S Typical gates (1) 30,000 50,000 Maximum system gates 119,000 199,000 1,728 2,880 Logic elements (LEs) EABs Total RAM bits Maximum user I/O pins Altera Corporation DS-F10KE-2.5 6 10 24,576 40,960 220 254 1 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 2. FLEX 10KE Device Features Feature EPF10K100E (2) EPF10K130E EPF10K200E EPF10K200S Typical gates (1) 100,000 130,000 200,000 Maximum system gates 257,000 342,000 513,000 4,992 6,656 9,984 12 16 24 49,152 65,536 98,304 338 413 470 Logic elements (LEs) EABs Total RAM bits Maximum user I/O pins Note to tables: (1) (2) The embedded IEEE Std. 1149.1 JTAG circuitry adds up to 31,250 gates in addition to the listed typical or maximum system gates. New EPF10K100B designs should use EPF10K100E devices. ...and More Features - 2 Fabricated on an advanced process and operate with a 2.5-V internal supply voltage - In-circuit reconfigurability (ICR) via external configuration devices, intelligent controller, or JTAG port - ClockLockTM and ClockBoostTM options for reduced clock delay/skew and clock multiplication - Built-in low-skew clock distribution trees - 100% functional testing of all devices; test vectors or scan chains are not required - Pull-up on I/O pins before and during configuration Flexible interconnect - FastTrack(R) Interconnect continuous routing structure for fast, predictable interconnect delays - Dedicated carry chain that implements arithmetic functions such as fast adders, counters, and comparators (automatically used by software tools and megafunctions) - Dedicated cascade chain that implements high-speed, high-fan-in logic functions (automatically used by software tools and megafunctions) - Tri-state emulation that implements internal tri-state buses - Up to six global clock signals and four global clear signals Powerful I/O pins - Individual tri-state output enable control for each pin - Open-drain option on each I/O pin - Programmable output slew-rate control to reduce switching noise - Clamp to VCCIO user-selectable on a pin-by-pin basis - Supports hot-socketing Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Software design support and automatic place-and-route provided by Altera's development systems for Windows-based PCs and Sun SPARCstation, and HP 9000 Series 700/800 Flexible package options - Available in a variety of packages with 144 to 672 pins, including the innovative FineLine BGATM packages (see Tables 3 and 4) - SameFrameTM pin-out compatibility between FLEX 10KA and FLEX 10KE devices across a range of device densities and pin counts Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), DesignWare components, Verilog HDL, VHDL, and other interfaces to popular EDA tools from manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, VeriBest, and Viewlogic Table 3. FLEX 10KE Package Options & I/O Pin Count Device 144-Pin TQFP 208-Pin PQFP EPF10K30E 102 147 176 220 220 (3) EPF10K50E 102 147 189 191 254 254 (3) EPF10K50S 102 147 189 191 220 254 254 (3) 147 189 191 274 338 338 (3) 274 369 EPF10K100E EPF10K130E 240-Pin PQFP RQFP Notes (1), (2) 186 256-Pin 356-Pin 484-Pin 599-Pin FineLine BGA FineLine PGA BGA BGA EPF10K200E EPF10K200S 182 274 369 600-Pin 672-Pin BGA FineLine BGA 424 413 470 470 470 470 470 470 Notes: (1) (2) (3) FLEX 10KE device package types include thin quad flat pack (TQFP), plastic quad flat pack (PQFP), power quad flat pack (RQFP), pin-grid array (PGA), and ball-grid array (BGA) packages. Devices in the same package are pin-compatible, although some devices have more I/O pins than others. When planning device migration, use the I/O pins that are common to all devices. This option is supported with a 484-pin FineLine BGA package. By using SameFrame pin migration, all FineLine BGA packages are pin-compatible. For example, a board can be designed to support 256-pin, 484-pin, and 672-pin FineLine BGA packages. The Altera software automatically avoids conflicting pins when future migration is set. Altera Corporation 3 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 4. FLEX 10KE Package Sizes Device 144Pin TQFP 208-Pin PQFP 240-Pin PQFP RQFP 256-Pin FineLine BGA Pitch (mm) 0.50 0.50 0.50 1.0 1.27 1.0 - 1.27 1.0 Area (mm 2) 484 936 1,197 289 1,225 529 3,904 2,025 729 Length x width 22 x 22 30.6 x 30.6 34.6 x 34.6 17 x 17 (mm x mm) General Description 356Pin BGA 484-Pin FineLine BGA 599-Pin PGA 600Pin BGA 672-Pin FineLine BGA 35 x 35 23 x 23 62.5 x 62.5 45 x 45 27 x 27 Altera FLEX 10KE devices are enhanced versions of FLEX 10K devices. Based on reconfigurable CMOS SRAM elements, the FLEX architecture incorporates all features necessary to implement common gate array megafunctions. With up to 200,000 typical gates, FLEX 10KE devices provide the density, speed, and features to integrate entire systems, including multiple 32-bit buses, into a single device. The ability to reconfigure FLEX 10KE devices enables 100% testing prior to shipment and allows the designer to focus on simulation and design verification. FLEX 10KE reconfigurability eliminates inventory management for gate array designs and generation of test vectors for fault coverage. Table 5 shows FLEX 10KE performance for some common designs. All performance values were obtained with Synopsys DesignWare or LPM functions. Special design techniques are not required to implement the applications; the designer simply infers or instantiates a function in a Verilog HDL, VHDL, Altera Hardware Description Language (AHDL), or schematic design file. 4 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 5. FLEX 10KE Performance Application Resources Used Performance Units LEs EABs 16-bit loadable counter 16 0 -1 Speed Grade -2 Speed Grade -3 Speed Grade 285 250 200 MHz 16-bit accumulator 16 0 285 250 200 MHz 16-to-1 multiplexer (1) 10 0 3.5 4.9 7.0 ns 16-bit multiplier with 3-stage pipeline (2) 592 0 156 131 93 MHz 256 x 16 RAM read cycle speed (2) 0 1 196 154 118 MHz 256 x 16 RAM write cycle speed (2) 0 1 185 143 106 MHz Notes: (1) (2) This application uses combinatorial inputs and outputs. This application uses registered inputs and outputs. Table 6 shows FLEX 10KE performance for more complex designs. These designs are available as Altera MegaCore(R) functions. Table 6. FLEX 10KE Performance for Complex Designs Application LEs Used Performance Units -1 Speed Grade -2 Speed Grade -3 Speed Grade 8-bit, 16-tap parallel finite impulse response (FIR) filter 8-bit, 512-point fast Fourier transform (FFT) function a16450 universal asynchronous receiver/transmitter (UART) 597 192 156 116 MSPS 1,854 23.4 28.7 38.9 s (1) 113 92 68 MHz 36 28 20.5 MHz 342 Note: (1) These values are for calculation time. Calculation time = number of clocks required/fmax. Number of clocks required = ceiling [log 2 (points)/2] x [points +14 + ceiling] Altera Corporation 5 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Similar to the FLEX 10KE architecture, embedded gate arrays are the fastest-growing segment of the gate array market. As with standard gate arrays, embedded gate arrays implement general logic in a conventional "sea-of-gates" architecture. Additionally, embedded gate arrays have dedicated die areas for implementing large, specialized functions. By embedding functions in silicon, embedded gate arrays reduce die area and increase speed when compared to standard gate arrays. While embedded megafunctions typically cannot be customized, FLEX 10KE devices are programmable, providing the designer with full control over embedded megafunctions and general logic, while facilitating iterative design changes during debugging. Each FLEX 10KE device contains an embedded array and a logic array. The embedded array is used to implement a variety of memory functions or complex logic functions, such as digital signal processing (DSP), wide data-path manipulation, microcontroller applications, and datatransformation functions. The logic array performs the same function as the sea-of-gates in the gate array and is used to implement general logic such as counters, adders, state machines, and multiplexers. The combination of embedded and logic arrays provides the high performance and high density of embedded gate arrays, enabling designers to implement an entire system on a single device. FLEX 10KE devices are configured at system power-up with data stored in an Altera serial configuration device or provided by a system controller. Altera offers the EPC1, EPC2, and EPC16 configuration devices, which configure FLEX 10KE devices via a serial data stream. Configuration data can also be downloaded from system RAM or via the Altera BitBlasterTM, ByteBlasterMVTM, or MasterBlaster download cables. After a FLEX 10KE device has been configured, it can be reconfigured in-circuit by resetting the device and loading new data. Because reconfiguration requires less than 85 ms, real-time changes can be made during system operation. FLEX 10KE devices contain an interface that permits microprocessors to configure FLEX 10KE devices serially or in-parallel, and synchronously or asynchronously. The interface also enables microprocessors to treat a FLEX 10KE device as memory and configure it by writing to a virtual memory location, making it easy to reconfigure the device. 6 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet f For more information on FLEX device configuration, see the following documents: Configuration Devices for APEX & FLEX Devices Data Sheet BitBlaster Serial Download Cable Data Sheet ByteBlasterMV Parallel Port Download Cable Data Sheet MasterBlaster Download Cable Data Sheet Application Note 116 (Configuring APEX 20K, FLEX 10K, & FLEX 6000 Devices) FLEX 10KE devices are supported by the Altera development systems, which are integrated packages that offer schematic, text (including AHDL), and waveform design entry, compilation and logic synthesis, full simulation and worst-case timing analysis, and device configuration. The Altera software provides EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for additional design entry and simulation support from other industry-standard PC- and UNIX workstation-based EDA tools. The Altera software works easily with common gate array EDA tools for synthesis and simulation. For example, the Altera software can generate Verilog HDL files for simulation with tools such as Cadence Verilog-XL. Additionally, the Altera software contains EDA libraries that use devicespecific features such as carry chains, which are used for fast counter and arithmetic functions. For instance, the Synopsys Design Compiler library supplied with the Altera development system includes DesignWare functions that are optimized for the FLEX 10KE architecture. The Altera development system runs on Windows-based PCs and Sun SPARCstation, and HP 9000 Series 700/800. f Altera Corporation See the MAX+PLUS II Programmable Logic Development System & Software Data Sheet and the Quartus Programmable Logic Development System & Software Data Sheet for more information. 7 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Functional Description Each FLEX 10KE device contains an enhanced embedded array to implement memory and specialized logic functions, and a logic array to implement general logic. The embedded array consists of a series of EABs. When implementing memory functions, each EAB provides 4,096 bits, which can be used to create RAM, ROM, dual-port RAM, or first-in first-out (FIFO) functions. When implementing logic, each EAB can contribute 100 to 600 gates towards complex logic functions, such as multipliers, microcontrollers, state machines, and DSP functions. EABs can be used independently, or multiple EABs can be combined to implement larger functions. The logic array consists of logic array blocks (LABs). Each LAB contains eight LEs and a local interconnect. An LE consists of a four-input look-up table (LUT), a programmable flipflop, and dedicated signal paths for carry and cascade functions. The eight LEs can be used to create medium-sized blocks of logic--such as 8-bit counters, address decoders, or state machines--or combined across LABs to create larger logic blocks. Each LAB represents about 96 usable gates of logic. Signal interconnections within FLEX 10KE devices (as well as to and from device pins) are provided by the FastTrack Interconnect routing structure, which is a series of fast, continuous row and column channels that run the entire length and width of the device. Each I/O pin is fed by an I/O element (IOE) located at the end of each row and column of the FastTrack Interconnect routing structure. Each IOE contains a bidirectional I/O buffer and a flipflop that can be used as either an output or input register to feed input, output, or bidirectional signals. When used with a dedicated clock pin, these registers provide exceptional performance. As inputs, they provide setup times as low as 0.9 ns and hold times of 0 ns. As outputs, these registers provide clock-to-output times as low as 3.0 ns. IOEs provide a variety of features, such as JTAG BST support, slew-rate control, tri-state buffers, and open-drain outputs. 8 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 1 shows a block diagram of the FLEX 10KE architecture. Each group of LEs is combined into an LAB; groups of LABs are arranged into rows and columns. Each row also contains a single EAB. The LABs and EABs are interconnected by the FastTrack Interconnect routing structure. IOEs are located at the end of each row and column of the FastTrack Interconnect routing structure. Figure 1. FLEX 10KE Device Block Diagram Embedded Array Block (EAB) I/O Element (IOE) IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Column Interconnect Logic Array EAB Logic Array Block (LAB) IOE IOE IOE IOE Logic Element (LE) Row Interconnect EAB Local Interconnect Logic Array IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Embedded Array FLEX 10KE devices provide six dedicated inputs that drive the flipflops' control inputs and ensure the efficient distribution of high-speed, lowskew (less than 1.5 ns) control signals. These signals use dedicated routing channels that provide shorter delays and lower skews than the FastTrack Interconnect routing structure. Four of the dedicated inputs drive four global signals. These four global signals can also be driven by internal logic, providing an ideal solution for a clock divider or an internally generated asynchronous clear signal that clears many registers in the device. Altera Corporation 9 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Embedded Array Block The EAB is a flexible block of RAM, with registers on the input and output ports, that is used to implement common gate array megafunctions. Because it is large and flexible, the EAB is suitable for functions such as multipliers, vector scalars, and error correction circuits. These functions can be combined in applications such as digital filters and microcontrollers. Logic functions are implemented by programming the EAB with a readonly pattern during configuration, thereby creating a large LUT. With LUTs, combinatorial functions are implemented by looking up the results, rather than by computing them. This implementation of combinatorial functions can be faster than using algorithms implemented in general logic, a performance advantage that is further enhanced by the fast access times of EABs. The large capacity of EABs enables designers to implement complex functions in one logic level without the routing delays associated with linked LEs or field-programmable gate array (FPGA) RAM blocks. For example, a single EAB can implement any function with 8 inputs and 16 outputs. Parameterized functions such as LPM functions can take advantage of the EAB automatically. The FLEX 10KE EAB provides advantages over FPGAs, which implement on-board RAM as arrays of small, distributed RAM blocks. These small FPGA RAM blocks must be connected together to make RAM blocks of manageable size. The RAM blocks are connected together using multiplexers implemented with more logic blocks. These extra multiplexers cause extra delay, which slows down the RAM block. FPGA RAM blocks are also prone to routing problems because small blocks of RAM must be connected together to make larger blocks. In contrast, EABs can be used to implement large, dedicated blocks of RAM that eliminate these timing and routing concerns. The FLEX 10KE enhanced EAB adds dual-port capability to the existing EAB structure. The dual-port structure is ideal for FIFO buffers with one or two clocks. The FLEX 10KE EAB can also support up to 16-bit-wide RAM blocks and is backward-compatible with any design containing FLEX 10K EABs. The FLEX 10KE EAB can act in dual-port or single-port mode. When in dual-port mode, separate clocks may be used for EAB read and write sections, which allows the EAB to be written and read at different rates. It also has separate synchronous clock enable signals for the EAB read and write sections, which allow independent control of these sections. 10 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet The EAB can also be used for bidirectional, dual-port memory applications where two ports read or write simultaneously. To implement this type of dual-port memory, two EABs are used to support two simultaneous read or writes. Alternatively, one clock and clock enable can be used to control the input registers of the EAB, while a different clock and clock enable control the output registers (see Figure 2). Figure 2. FLEX 10KE Device in Dual-Port RAM Mode Notes (1) Dedicated Inputs & Global Signals Dedicated Clocks Row Interconnect 2 RAM/ROM 256 x 16 512 x 8 Data In 1,024 x 4 2,048 x 2 4 data[ ] D Q ENA Data Out 4, 8, 16, 32 D ENA rdaddress[ ] EAB Local Interconnect (2) 4, 8 Read Address D Q ENA wraddress[ ] Write Address D rden Q Q 4, 8, 16, 32 ENA Read Enable wren D Q ENA outclocken Write Enable inclocken D ENA inclock outclock Q Write Pulse Generator Multiplexers allow read address and read enable registers to be clocked by inclock or outclock signals. Column Interconnect Notes: (1) (2) All registers can be asynchronously cleared by EAB local interconnect signals, global signals, or the chip-wide reset. EPF10K30E and EPF10K50E devices have 88 EAB local interconnect channels; EPF10K100E, EPF10K130E, and EPF10K200E devices have 104 EAB local interconnect channels. Altera Corporation 11 FLEX 10KE Embedded Programmable Logic Devices Data Sheet The EAB can also use Altera megafunctions to implement dual-port RAM applications where both ports can read or write, as shown in Figure 3. Figure 3. FLEX 10KE EAB in Dual-Port RAM Mode Port A Port B address_a[] address_b[] data_a[] we_a clkena_a Clock A data_b[] we_b clkena_b Clock B The FLEX 10KE EAB can be used in a single-port mode, which is useful for backward-compatibility with FLEX 10K designs (see Figure 4). 12 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 4. FLEX 10KE Device in Single-Port RAM Mode Dedicated Inputs & Global Signals Dedicated Clocks 2 Chip-Wide Reset Row Interconnect 4 D Q 8, 4, 2, 1 Data Out EAB Local Interconnect (1) 4, 8, 16, 32 RAM/ROM 256 x 16 512 x 8 Data In 1,024 x 4 2,048 x 2 D Q 4, 8 Address D Q 8, 9, 10, 11 4, 8, 16, 32 Write Enable D Q Column Interconnect Note: (1) EPF10K30E, EPF10K50E, and EPF10K50S devices have 88 EAB local interconnect channels; EPF10K100E, EPF10K130E, EPF10K200E, and EPF10K200S devices have 104 EAB local interconnect channels. EABs can be used to implement synchronous RAM, which is easier to use than asynchronous RAM. A circuit using asynchronous RAM must generate the RAM write enable signal, while ensuring that its data and address signals meet setup and hold time specifications relative to the write enable signal. In contrast, the EAB's synchronous RAM generates its own write enable signal and is self-timed with respect to the input or write clock. A circuit using the EAB's self-timed RAM must only meet the setup and hold time specifications of the global clock. Altera Corporation 13 FLEX 10KE Embedded Programmable Logic Devices Data Sheet When used as RAM, each EAB can be configured in any of the following sizes: 256 x 16, 512 x 8, 1,024 x 4, or 2,048 x 2 (see Figure 5). Figure 5. FLEX 10KE EAB Memory Configurations 256 x 16 512 x 8 2,048 x 2 1,024 x 4 Larger blocks of RAM are created by combining multiple EABs. For example, two 256 x 16 RAM blocks can be combined to form a 256 x 32 block; two 512 x 8 RAM blocks can be combined to form a 512 x 16 block (see Figure 6). Figure 6. Examples of Combining FLEX 10KE EABs 256 x 32 512 x 16 256 x 16 512 x 8 256 x 16 512 x 8 If necessary, all EABs in a device can be cascaded to form a single RAM block. EABs can be cascaded to form RAM blocks of up to 2,048 words without impacting timing. The Altera software automatically combines EABs to meet a designer's RAM specifications. 14 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet EABs provide flexible options for driving and controlling clock signals. Different clocks and clock enables can be used for reading and writing to the EAB. Registers can be independently inserted on the data input, EAB output, write address, write enable signals, read address, and read enable signals. The global signals and the EAB local interconnect can drive write enable, read enable, and clock enable signals. The global signals, dedicated clock pins, and EAB local interconnect can drive the EAB clock signals. Because the LEs drive the EAB local interconnect, the LEs can control write enable, read enable, clear, clock, and clock enable signals. An EAB is fed by a row interconnect and can drive out to row and column interconnects. Each EAB output can drive up to two row channels and up to two column channels; the unused row channel can be driven by other LEs. This feature increases the routing resources available for EAB outputs (see Figures 2 and 4). The column interconnect, which is adjacent to the EAB, has twice as many channels as other columns in the device. Logic Array Block An LAB consists of eight LEs, their associated carry and cascade chains, LAB control signals, and the LAB local interconnect. The LAB provides the coarse-grained structure to the FLEX 10KE architecture, facilitating efficient routing with optimum device utilization and high performance (see Figure 7). Altera Corporation 15 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 7. FLEX 10KE LAB Dedicated Inputs & Global Signals (1) Row Interconnect ter terconnect 6 LAB Local Interconnect terconnect (2) ter (2) 16 6 See Figure 12 for details. 4 LAB Control Signals nal nals 4 Carry-In & Cascade-In 2 4 LE1 4 LE2 4 LE3 4 LE4 4 LE5 4 LE6 4 LE7 4 LE8 8 2 8 24 to 48 Column-to-Row Interconnect ter terconnect Column Interconnect ter terconnect 8 16 Carry-Out & Cascade-Out Notes: (1) (2) 16 EPF10K30E, EPF10K50E, and EPF10K50S devices have 22 inputs to the LAB local interconnect channel from the row; EPF10K100E, EPF10K130E, EPF10K200E, and EPF10K200S devices have 26. EPF10K30E, EPF10K50E, and EPF10K50S devices have 30 LAB local interconnect channels; EPF10K100E, EPF10K130E, EPF10K200E, and EPF10K200S devices have 34. Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Each LAB provides four control signals with programmable inversion that can be used in all eight LEs. Two of these signals can be used as clocks, the other two can be used for clear/preset control. The LAB clocks can be driven by the dedicated clock input pins, global signals, I/O signals, or internal signals via the LAB local interconnect. The LAB preset and clear control signals can be driven by the global signals, I/O signals, or internal signals via the LAB local interconnect. The global control signals are typically used for global clock, clear, or preset signals because they provide asynchronous control with very low skew across the device. If logic is required on a control signal, it can be generated in one or more LE in any LAB and driven into the local interconnect of the target LAB. In addition, the global control signals can be generated from LE outputs. Logic Element The LE, the smallest unit of logic in the FLEX 10KE architecture, has a compact size that provides efficient logic utilization. Each LE contains a four-input LUT, which is a function generator that can quickly compute any function of four variables. In addition, each LE contains a programmable flipflop with a synchronous clock enable, a carry chain, and a cascade chain. Each LE drives both the local and the FastTrack Interconnect routing structure (see Figure 8). Figure 8. FLEX 10KE Logic Element data1 data2 data3 data4 Look-Up Table (LUT) Carry-In Cascade-In Carry Chain Cascade Chain Register Bypass D PRN Q Programmable Register FastTrack Interconnect ENA CLRN LAB Local Interconnect labctrl1 labctrl2 Clear/ Preset Logic Chip-Wide Reset Clock Select labctrl3 labctrl4 Carry-Out Altera Corporation Cascade-Out 17 FLEX 10KE Embedded Programmable Logic Devices Data Sheet The programmable flipflop in the LE can be configured for D, T, JK, or SR operation. The clock, clear, and preset control signals on the flipflop can be driven by global signals, general-purpose I/O pins, or any internal logic. For combinatorial functions, the flipflop is bypassed and the output of the LUT drives the output of the LE. The LE has two outputs that drive the interconnect: one drives the local interconnect and the other drives either the row or column FastTrack Interconnect routing structure. The two outputs can be controlled independently. For example, the LUT can drive one output while the register drives the other output. This feature, called register packing, can improve LE utilization because the register and the LUT can be used for unrelated functions. The FLEX 10KE architecture provides two types of dedicated high-speed data paths that connect adjacent LEs without using local interconnect paths: carry chains and cascade chains. The carry chain supports high-speed counters and adders and the cascade chain implements wide-input functions with minimum delay. Carry and cascade chains connect all LEs in a LAB as well as all LABs in the same row. Intensive use of carry and cascade chains can reduce routing flexibility. Therefore, the use of these chains should be limited to speed-critical portions of a design. Carry Chain The carry chain provides a very fast (as low as 0.2 ns) carry-forward function between LEs. The carry-in signal from a lower-order bit drives forward into the higher-order bit via the carry chain, and feeds into both the LUT and the next portion of the carry chain. This feature allows the FLEX 10KE architecture to implement high-speed counters, adders, and comparators of arbitrary width efficiently. Carry chain logic can be created automatically by the Altera Compiler during design processing, or manually by the designer during design entry. Parameterized functions such as LPM and DesignWare functions automatically take advantage of carry chains. Carry chains longer than eight LEs are automatically implemented by linking LABs together. For enhanced fitting, a long carry chain skips alternate LABs in a row. A carry chain longer than one LAB skips either from even-numbered LAB to even-numbered LAB, or from oddnumbered LAB to odd-numbered LAB. For example, the last LE of the first LAB in a row carries to the first LE of the third LAB in the row. The carry chain does not cross the EAB at the middle of the row. For instance, in the EPF10K50E device, the carry chain stops at the eighteenth LAB and a new one begins at the nineteenth LAB. 18 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 9 shows how an n-bit full adder can be implemented in n + 1 LEs with the carry chain. One portion of the LUT generates the sum of two bits using the input signals and the carry-in signal; the sum is routed to the output of the LE. The register can be bypassed for simple adders or used for an accumulator function. Another portion of the LUT and the carry chain logic generates the carry-out signal, which is routed directly to the carry-in signal of the next-higher-order bit. The final carry-out signal is routed to an LE, where it can be used as a general-purpose signal. Figure 9. FLEX 10KE Carry Chain Operation (n-Bit Full Adder) Carry-In a1 b1 LUT s1 Register Carry Chain LE1 a2 b2 LUT s2 Register Carry Chain LE2 an bn LUT sn Register Carry Chain LEn LUT Register Carry-Out Carry Chain LEn + 1 Altera Corporation 19 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Cascade Chain With the cascade chain, the FLEX 10KE architecture can implement functions that have a very wide fan-in. Adjacent LUTs can be used to compute portions of the function in parallel; the cascade chain serially connects the intermediate values. The cascade chain can use a logical AND or logical OR (via De Morgan's inversion) to connect the outputs of adjacent LEs. An a delay as low as 0.6 ns per LE, each additional LE provides four more inputs to the effective width of a function. Cascade chain logic can be created automatically by the Altera Compiler during design processing, or manually by the designer during design entry. Cascade chains longer than eight bits are implemented automatically by linking several LABs together. For easier routing, a long cascade chain skips every other LAB in a row. A cascade chain longer than one LAB skips either from even-numbered LAB to even-numbered LAB, or from odd-numbered LAB to odd-numbered LAB (e.g., the last LE of the first LAB in a row cascades to the first LE of the third LAB). The cascade chain does not cross the center of the row (e.g., in the EPF10K50E device, the cascade chain stops at the eighteenth LAB and a new one begins at the nineteenth LAB). This break is due to the EAB's placement in the middle of the row. Figure 10 shows how the cascade function can connect adjacent LEs to form functions with a wide fan-in. These examples show functions of 4n variables implemented with n LEs. The LE delay is 0.9 ns; the cascade chain delay is 0.6 ns. With the cascade chain, 2.7 ns are needed to decode a 16-bit address. Figure 10. FLEX 10KE Cascade Chain Operation AND Cascade Chain d[3..0] OR Cascade Chain d[3..0] LUT LUT LE1 d[7..4] LE1 d[7..4] LUT LUT LE2 d[(4n - 1)..(4n - 4)] d[(4n - 1)..(4n - 4)] LUT LEn 20 LE2 LUT LEn Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet LE Operating Modes The FLEX 10KE LE can operate in the following four modes: Normal mode Arithmetic mode Up/down counter mode Clearable counter mode Each of these modes uses LE resources differently. In each mode, seven available inputs to the LE--the four data inputs from the LAB local interconnect, the feedback from the programmable register, and the carry-in and cascade-in from the previous LE--are directed to different destinations to implement the desired logic function. Three inputs to the LE provide clock, clear, and preset control for the register. The Altera software, in conjunction with parameterized functions such as LPM and DesignWare functions, automatically chooses the appropriate mode for common functions such as counters, adders, and multipliers. If required, the designer can also create special-purpose functions that use a specific LE operating mode for optimal performance. The architecture provides a synchronous clock enable to the register in all four modes. The Altera software can set DATA1 to enable the register synchronously, providing easy implementation of fully synchronous designs. Altera Corporation 21 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 11 shows the LE operating modes. Figure 11. FLEX 10KE LE Operating Modes Normal Mode Cascade-In Carry-In LE-Out to FastTrack Interconnect data1 data2 4-Input LUT data3 D PRN Q LE-Out to Local Interconnect ENA CLRN data4 Cascade-Out Arithmetic Mode Carry-In Cascade-In LE-Out data1 data2 PRN D Q 3-Input LUT ENA CLRN 3-Input LUT Cascade-Out Carry-Out Up/Down Counter Mode Cascade-In Carry-In data1 (ena) data2 (u/d) 3-Input LUT 1 D PRN Q LE-Out 0 data3 (data) ENA CLRN 3-Input LUT data4 (nload) Carry-Out Cascade-Out Clearable Counter Mode Carry-In data1 (ena) data2 (nclr) 3-Input LUT D 1 PRN Q LE-Out 0 data3 (data) ENA CLRN 3-Input LUT data4 (nload) 22 Carry-Out Cascade-Out Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Normal Mode The normal mode is suitable for general logic applications and wide decoding functions that can take advantage of a cascade chain. In normal mode, four data inputs from the LAB local interconnect and the carry-in are inputs to a four-input LUT. The Altera Compiler automatically selects the carry-in or the DATA3 signal as one of the inputs to the LUT. The LUT output can be combined with the cascade-in signal to form a cascade chain through the cascade-out signal. Either the register or the LUT can be used to drive both the local interconnect and the FastTrack Interconnect routing structure at the same time. The LUT and the register in the LE can be used independently (register packing). To support register packing, the LE has two outputs; one drives the local interconnect, and the other drives the FastTrack Interconnect routing structure. The DATA4 signal can drive the register directly, allowing the LUT to compute a function that is independent of the registered signal; a three-input function can be computed in the LUT, and a fourth independent signal can be registered. Alternatively, a four-input function can be generated, and one of the inputs to this function can be used to drive the register. The register in a packed LE can still use the clock enable, clear, and preset signals in the LE. In a packed LE, the register can drive the FastTrack Interconnect routing structure while the LUT drives the local interconnect, or vice versa. Arithmetic Mode The arithmetic mode offers 2 three-input LUTs that are ideal for implementing adders, accumulators, and comparators. One LUT computes a three-input function; the other generates a carry output. As shown in Figure 11 on page 22, the first LUT uses the carry-in signal and two data inputs from the LAB local interconnect to generate a combinatorial or registered output. For example, in an adder, this output is the sum of three signals: a, b, and carry-in. The second LUT uses the same three signals to generate a carry-out signal, thereby creating a carry chain. The arithmetic mode also supports simultaneous use of the cascade chain. Up/Down Counter Mode The up/down counter mode offers counter enable, clock enable, synchronous up/down control, and data loading options. These control signals are generated by the data inputs from the LAB local interconnect, the carry-in signal, and output feedback from the programmable register. Use 2 three-input LUTs: one generates the counter data, and the other generates the fast carry bit. A 2-to-1 multiplexer provides synchronous loading. Data can also be loaded asynchronously with the clear and preset register control signals without using the LUT resources. Altera Corporation 23 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Clearable Counter Mode The clearable counter mode is similar to the up/down counter mode, but supports a synchronous clear instead of the up/down control. The clear function is substituted for the cascade-in signal in the up/down counter mode. Use 2 three-input LUTs: one generates the counter data, and the other generates the fast carry bit. Synchronous loading is provided by a 2-to-1 multiplexer. The output of this multiplexer is AND ed with a synchronous clear signal. Internal Tri-State Emulation Internal tri-state emulation provides internal tri-states without the limitations of a physical tri-state bus. In a physical tri-state bus, the tri-state buffers' output enable (OE) signals select which signal drives the bus. However, if multiple OE signals are active, contending signals can be driven onto the bus. Conversely, if no OE signals are active, the bus will float. Internal tri-state emulation resolves contending tri-state buffers to a low value and floating buses to a high value, thereby eliminating these problems. The Altera software automatically implements tri-state bus functionality with a multiplexer. Clear & Preset Logic Control Logic for the programmable register's clear and preset functions is controlled by the DATA3, LABCTRL1, and LABCTRL2 inputs to the LE. The clear and preset control structure of the LE asynchronously loads signals into a register. Either LABCTRL1 or LABCTRL2 can control the asynchronous clear. Alternatively, the register can be set up so that LABCTRL1 implements an asynchronous load. The data to be loaded is driven to DATA3; when LABCTRL1 is asserted, DATA3 is loaded into the register. During compilation, the Altera Compiler automatically selects the best control signal implementation. Because the clear and preset functions are active-low, the Compiler automatically assigns a logic high to an unused clear or preset. The clear and preset logic is implemented in one of the following six modes chosen during design entry: 24 Asynchronous clear Asynchronous preset Asynchronous clear and preset Asynchronous load with clear Asynchronous load with preset Asynchronous load without clear or preset Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet In addition to the six clear and preset modes, FLEX 10KE devices provide a chip-wide reset pin that can reset all registers in the device. Use of this feature is set during design entry. In any of the clear and preset modes, the chip-wide reset overrides all other signals. Registers with asynchronous presets may be preset when the chip-wide reset is asserted. Inversion can be used to implement the asynchronous preset. Figure 12 shows examples of how to setup the preset and clear inputs for the desired functionality. Figure 12. FLEX 10KE LE Clear & Preset Modes Asynchronous Clear Asynchronous Preset Asynchronous Preset & Clear labctrl1 VCC PRN D Q Chip-Wide Reset labctrl1 or labctrl2 D D labctrl1 or labctrl2 Chip-Wide Reset PRN Q PRN Q CLRN CLRN labctrl2 Chip-Wide Reset CLRN VCC Asynchronous Load without Clear or Preset Asynchronous Load with Clear NOT NOT labctrl1 (Asynchronous Load) labctrl1 (Asynchronous Load) data3 (Data) D NOT PRN Q data3 (Data) D CLRN CLRN labctrl2 (Clear) Chip-Wide Reset PRN Q NOT Chip-Wide Reset Asynchronous Load with Preset NOT labctrl1 (Asynchronous Load) labctrl2 (Preset) D PRN Q data3 (Data) CLRN NOT Chip-Wide Reset Altera Corporation 25 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Asynchronous Clear The flipflop can be cleared by either LABCTRL1 or LABCTRL2. In this mode, the preset signal is tied to VCC to deactivate it. Asynchronous Preset An asynchronous preset is implemented as an asynchronous load, or with an asynchronous clear. If DATA3 is tied to VCC, asserting LABCTRL1 asynchronously loads a one into the register. Alternatively, the Altera software can provide preset control by using the clear and inverting the input and output of the register. Inversion control is available for the inputs to both LEs and IOEs. Therefore, if a register is preset by only one of the two LABCTRL signals, the DATA3 input is not needed and can be used for one of the LE operating modes. Asynchronous Preset & Clear When implementing asynchronous clear and preset, LABCTRL1 controls the preset and LABCTRL2 controls the clear. DATA3 is tied to VCC, so that asserting LABCTRL1 asynchronously loads a one into the register, effectively presetting the register. Asserting LABCTRL2 clears the register. Asynchronous Load with Clear When implementing an asynchronous load in conjunction with the clear, LABCTRL1 implements the asynchronous load of DATA3 by controlling the register preset and clear. LABCTRL2 implements the clear by controlling the register clear; LABCTRL2 does not have to feed the preset circuits. Asynchronous Load with Preset When implementing an asynchronous load in conjunction with preset, the Altera software provides preset control by using the clear and inverting the input and output of the register. Asserting LABCTRL2 presets the register, while asserting LABCTRL1 loads the register. The Altera software inverts the signal that drives DATA3 to account for the inversion of the register's output. Asynchronous Load without Preset or Clear When implementing an asynchronous load without preset or clear, LABCTRL1 implements the asynchronous load of DATA3 by controlling the register preset and clear. 26 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet FastTrack Interconnect Routing Structure In the FLEX 10KE architecture, connections between LEs, EABs, and device I/O pins are provided by the FastTrack Interconnect routing structure, which is a series of continuous horizontal and vertical routing channels that traverses the device. This global routing structure provides predictable performance, even in complex designs. In contrast, the segmented routing in FPGAs requires switch matrices to connect a variable number of routing paths, increasing the delays between logic resources and reducing performance. The FastTrack Interconnect routing structure consists of row and column interconnect channels that span the entire device. Each row of LABs is served by a dedicated row interconnect. The row interconnect can drive I/O pins and feed other LABs in the row. The column interconnect routes signals between rows and can drive I/O pins. Row channels drive into the LAB or EAB local interconnect. The row signal is buffered at every LAB or EAB to reduce the effect of fan-out on delay. A row channel can be driven by an LE or by one of three column channels. These four signals feed dual 4-to-1 multiplexers that connect to two specific row channels. These multiplexers, which are connected to each LE, allow column channels to drive row channels even when all eight LEs in a LAB drive the row interconnect. Each column of LABs or EABs is served by a dedicated column interconnect. The column interconnect that serves the EABs has twice as many channels as other column interconnects. The column interconnect can then drive I/O pins or another row's interconnect to route the signals to other LABs or EABs in the device. A signal from the column interconnect, which can be either the output of a LE or an input from an I/O pin, must be routed to the row interconnect before it can enter a LAB or EAB. Each row channel that is driven by an IOE or EAB can drive one specific column channel. Access to row and column channels can be switched between LEs in adjacent pairs of LABs. For example, a LE in one LAB can drive the row and column channels normally driven by a particular LE in the adjacent LAB in the same row, and vice versa. This flexibility enables routing resources to be used more efficiently (see Figure 13). Altera Corporation 27 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 13. FLEX 10KE LAB Connections to Row & Column Interconnect Column Channels To Other Columns Row Channels At each intersection, six row channels can drive column channels. Each LE can drive two row channels. From Adjacent LAB To Adjacent LAB LE 1 Each LE can switch interconnect access with an LE in the adjacent LAB. LE 2 LE 8 To LAB Local Interconnect 28 To Other Rows Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet For improved routing, the row interconnect consists of a combination of full-length and half-length channels. The full-length channels connect to all LABs in a row; the half-length channels connect to the LABs in half of the row. The EAB can be driven by the half-length channels in the left half of the row and by the full-length channels. The EAB drives out to the fulllength channels. In addition to providing a predictable, row-wide interconnect, this architecture provides increased routing resources. Two neighboring LABs can be connected using a half-row channel, thereby saving the other half of the channel for the other half of the row. Table 7 summarizes the FastTrack Interconnect routing structure resources available in each FLEX 10KE device. Table 7. FLEX 10KE FastTrack Interconnect Resources Device Rows Channels per Row Columns Channels per Column EPF10K30E 6 216 36 24 EPF10K50E EPF10K50S 10 216 36 24 EPF10K100E 12 312 52 24 EPF10K130E 16 312 52 32 EPF10K200E EPF10K200S 24 312 52 48 In addition to general-purpose I/O pins, FLEX 10KE devices have six dedicated input pins that provide low-skew signal distribution across the device. These six inputs can be used for global clock, clear, preset, and peripheral output enable and clock enable control signals. These signals are available as control signals for all LABs and IOEs in the device. The dedicated inputs can also be used as general-purpose data inputs because they can feed the local interconnect of each LAB in the device. Figure 14 shows the interconnection of adjacent LABs and EABs, with row, column, and local interconnects, as well as the associated cascade and carry chains. Each LAB is labeled according to its location: a letter represents the row and a number represents the column. For example, LAB B3 is in row B, column 3. Altera Corporation 29 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 14. FLEX 10KE Interconnect Resources See Figure 17 for details. I/O Element (IOE) IOE IOE IOE IOE IOE IOE IOE IOE IOE IOE Row Interconnect LAB A1 LAB A2 See Figure 16 for details. LAB A3 Column Interconnect LAB A5 LAB A4 IOE IOE IOE IOE LAB B1 LAB B2 Cascade & Carry Chains LAB B3 LAB B5 LAB B4 IOE IOE IOE IOE IOE IOE I/O Element An IOE contains a bidirectional I/O buffer and a register that can be used either as an input register for external data that requires a fast setup time, or as an output register for data that requires fast clock-to-output performance. In some cases, using an LE register for an input register will result in a faster setup time than using an IOE register. IOEs can be used as input, output, or bidirectional pins. For bidirectional registered I/O implementation, the output register should be in the IOE, and the data input and output enable registers should be LE registers placed adjacent to the bidirectional pin. The Altera Compiler uses the programmable inversion option to invert signals from the row and column interconnect automatically where appropriate. Figure 15 shows the bidirectional I/O registers. 30 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 15. FLEX 10KE Bidirectional I/O Registers Row and Column Interconnect 2 Dedicated Clock Inputs 4 Dedicated Inputs Peripheral Control Bus 2 4 OE Register 12 D Q ENA CLRN VCC Chip-Wide Reset VCC Chip-Wide Output Enable OE[7..0] (1) Programmable Delay VCC Output Register (2) D Q CLK[1..0] ENA CLRN CLK[3..2] VCC Open-Drain Output Slew-Rate Control ENA[5..0] VCC CLRN[1..0] Chip-Wide Reset Input Register (2) D Q VCC ENA CLRN Chip-Wide Reset Note: (1) All FLEX 10KE devices (except the EPF10K50E and EPF10K200E devices) have a programmable input delay buffer on the input path. Altera Corporation 31 FLEX 10KE Embedded Programmable Logic Devices Data Sheet On all FLEX 10KE devices (except EPF10K50E and EPF10K200E devices), the input path from the I/O pad to the FastTrack Interconnect has a programmable delay element that can be used to guarantee a zero hold time. EPF10K50S and EPF10K200S devices also support this feature. Depending on the placement of the IOE relative to what it is driving, the designer may choose to turn on the programmable delay to ensure a zero hold time or turn it off to minimize setup time. This feature is used to reduce setup time for complex pin-to-register paths (e.g., PCI designs). Each IOE selects the clock, clear, clock enable, and output enable controls from a network of I/O control signals called the peripheral control bus. The peripheral control bus uses high-speed drivers to minimize signal skew across the device and provides up to 12 peripheral control signals that can be allocated as follows: Up to eight output enable signals Up to six clock enable signals Up to two clock signals Up to two clear signals If more than six clock enable or eight output enable signals are required, each IOE on the device can be controlled by clock enable and output enable signals driven by specific LEs. In addition to the two clock signals available on the peripheral control bus, each IOE can use one of two dedicated clock pins. Each peripheral control signal can be driven by any of the dedicated input pins or the first LE of each LAB in a particular row. In addition, a LE in a different row can drive a column interconnect, which causes a row interconnect to drive the peripheral control signal. The chipwide reset signal resets all IOE registers, overriding any other control signals. When a dedicated clock pin drives IOE registers, it can be inverted for all IOEs in the device. All IOEs must use the same sense of the clock. For example, if any IOE uses the inverted clock, all IOEs must use the inverted clock and no IOE can use the non-inverted clock. However, LEs can still use the true or complement of the clock on a LAB-by-LAB basis. The incoming signal may be inverted at the dedicated clock pin and will drive all IOEs. For the true and complement of a clock to be used to drive IOEs, drive it into both global clock pins. One global clock pin will supply the true, and the other will supply the complement. When the true and complement of a dedicated input drives IOE clocks, two signals on the peripheral control bus are consumed, one for each sense of the clock. 32 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet When dedicated inputs drive non-inverted and inverted peripheral clears, clock enables, and output enables, two signals on the peripheral control bus will be used. Tables 8 and 9 list the sources for each peripheral control signal, and show how the output enable, clock enable, clock, and clear signals share 12 peripheral control signals. The tables also show the rows that can drive global signals. Table 8. Peripheral Bus Sources for EPF10K30E, EPF10K50E & EPF10K50S Devices Peripheral Control Signal EPF10K30E EPF10K50E EPF10K50S OE0 Row A Row A OE1 Row B Row B OE2 Row C Row D OE3 Row D Row F OE4 Row E Row H OE5 Row F Row J CLKENA0/CLK0/GLOBAL0 Row A Row A CLKENA1/OE6/GLOBAL1 Row B Row C CLKENA2/CLR0 Row C Row E CLKENA3/OE7/GLOBAL2 Row D Row G CLKENA4/CLR1 Row E Row I CLKENA5/CLK1/GLOBAL3 Row F Row J Altera Corporation 33 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 9. Peripheral Bus Sources for EPF10K100E, EPF10K130E, EPF10K200E & EPF10K200S Devices Peripheral Control Signal EPF10K100E EPF10K130E EPF10K200E EPF10K200S OE0 Row A Row C Row G OE1 Row C Row E Row I OE2 Row E Row G Row K OE3 Row L Row N Row R OE4 Row I Row K Row O OE5 Row K Row M Row Q CLKENA0/CLK0/GLOBAL0 Row F Row H Row L CLKENA1/OE6/GLOBAL1 Row D Row F Row J CLKENA2/CLR0 Row B Row D Row H CLKENA3/OE7/GLOBAL2 Row H Row J Row N CLKENA4/CLR1 Row J Row L Row P CLKENA5/CLK1/GLOBAL3 Row G Row I Row M Signals on the peripheral control bus can also drive the four global signals, referred to as GLOBAL0 through GLOBAL3 in Tables 8 and 9. An internally generated signal can drive a global signal, providing the same low-skew, low-delay characteristics as a signal driven by an input pin. An LE drives the global signal by driving a row line that drives the peripheral bus, which then drives the global signal. This feature is ideal for internally generated clear or clock signals with high fan-out. However, internally driven global signals offer no advantage over the general-purpose interconnect for routing data signals. The dedicated input pin should be driven to a known logic state (such as ground) and not be allowed to float. The chip-wide output enable pin is an active-high pin (DEV_OE) that can be used to tri-state all pins on the device. This option can be set in the Altera software. On EPF10K50E and EPF10K200E devices, the built-in I/O pin pull-up resistors (which are active during configuration) are active when the chip-wide output enable pin is asserted. The registers in the IOE can also be reset by the chip-wide reset pin. 34 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Row-to-IOE Connections When an IOE is used as an input signal, it can drive two separate row channels. The signal is accessible by all LEs within that row. When an IOE is used as an output, the signal is driven by a multiplexer that selects a signal from the row channels. Up to eight IOEs connect to each side of each row channel (see Figure 16). Figure 16. FLEX 10KE Row-to-IOE Connections The values for m and n are provided in Table 10. IOE1 m Row FastTrack Interconnect n n n IOE8 m Each IOE is driven by an m-to-1 multiplexer. Each IOE can drive two row channels. Table 10 lists the FLEX 10KE row-to-IOE interconnect resources. Table 10. FLEX 10KE Row-to-IOE Interconnect Resources Device Altera Corporation Channels per Row (n) Row Channels per Pin (m) EPF10K30E 216 27 EPF10K50E EPF10K50S 216 27 EPF10K100E 312 39 EPF10K130E 312 39 EPF10K200E EPF10K200S 312 39 35 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Column-to-IOE Connections When an IOE is used as an input, it can drive up to two separate column channels. When an IOE is used as an output, the signal is driven by a multiplexer that selects a signal from the column channels. Two IOEs connect to each side of the column channels. Each IOE can be driven by column channels via a multiplexer. The set of column channels is different for each IOE (see Figure 17). Figure 17. FLEX 10KE Column-to-IOE Connections The values for m and n are provided in Table 11. Each IOE is driven by a m-to-1 multiplexer Column Interconnect m IOE1 m IOE1 n n n Each IOE can drive two column channels. Table 11 lists the FLEX 10KE column-to-IOE interconnect resources. Table 11. FLEX 10KE Column-to-IOE Interconnect Resources Device 36 Channels per Column (n) Column Channels per Pin (m) EPF10K30E 24 16 EPF10K50E EPF10K50S 24 16 EPF10K100E 24 16 EPF10K130E 32 24 EPF10K200E EPF10K200S 48 40 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet SameFrame Pin-Outs FLEX 10KE devices support the SameFrame pin-out feature for FineLine BGA packages. The SameFrame pin-out feature is the arrangement of balls on FineLine BGA packages such that the lower-ballcount packages form a subset of the higher-ball-count packages. SameFrame pin-outs provide the flexibility to migrate not only from device to device within the same package, but also from one package to another. A given printed circuit board (PCB) layout can support multiple device density/package combinations. For example, a single board layout can support a range of devices from an EPF10K30E device in a 256-pin FineLine BGA package to an EPF10K200S device in a 672-pin FineLine BGA package. The Altera software provides support to design PCBs with SameFrame pin-out devices. Devices can be defined for present and future use. The Altera software generates pin-outs describing how to lay out a board to take advantage of this migration (see Figure 18). Figure 18. SameFrame Pin-Out Example Printed Circuit Board Designed for 672-Pin FineLine BGA Package 100-Pin FineLine BGA 256-Pin FineLine BGA Package (Reduced I/O Count or Logic Requirements) Altera Corporation 256-Pin FineLine BGA 672-Pin FineLine BGA Package (Increased I/O Count or Logic Requirements) 37 FLEX 10KE Embedded Programmable Logic Devices Data Sheet ClockLock & ClockBoost Features To support high-speed designs, FLEX 10KE devices offer optional ClockLock and ClockBoost circuitry containing a phase-locked loop (PLL) used to increase design speed and reduce resource usage. The ClockLock circuitry uses a synchronizing PLL that reduces the clock delay and skew within a device. This reduction minimizes clock-to-output and setup times while maintaining zero hold times. The ClockBoost circuitry, which provides a clock multiplier, allows the designer to enhance device area efficiency by resource sharing within the device. The ClockBoost feature allows the designer to distribute a low-speed clock and multiply that clock on-device. Combined, the ClockLock and ClockBoost features provide significant improvements in system performance and bandwidth. All FLEX 10KE devices, except EPF10K50E and EPF10K200E devices, support ClockLock and ClockBoost circuitry. EPF10K50S and EPF10K200S devices support this circuitry. Devices that support ClockLock and ClockBoost circuitry are distinguished with an "X" suffix in the ordering code; for instance, the EPF10K200SFC672-1X device supports this circuit. The ClockLock and ClockBoost features in FLEX 10KE devices are enabled through the Altera software. External devices are not required to use these features. The output of the ClockLock and ClockBoost circuits is not available at any of the device pins. The ClockLock and ClockBoost circuitry locks onto the rising edge of the incoming clock. The circuit output can drive the clock inputs of registers only; the generated clock cannot be gated or inverted. The dedicated clock pin (GCLK1) supplies the clock to the ClockLock and ClockBoost circuitry. When the dedicated clock pin is driving the ClockLock or ClockBoost circuitry, it cannot drive elsewhere in the device. For designs that require both a multiplied and non-multiplied clock, the clock trace on the board can be connected to the GCLK1 pin. In the Altera software, the GCLK1 pin can feed both the ClockLock and ClockBoost circuitry in the FLEX 10KE device. However, when both circuits are used, the other clock pin cannot be used. 38 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet ClockLock & ClockBoost Timing Parameters For the ClockLock and ClockBoost circuitry to function properly, the incoming clock must meet certain requirements. If these specifications are not met, the circuitry may not lock onto the incoming clock, which generates an erroneous clock within the device. The clock generated by the ClockLock and ClockBoost circuitry must also meet certain specifications. If the incoming clock meets these requirements during configuration, the ClockLock and ClockBoost circuitry will lock onto the clock during configuration. The circuit will be ready for use immediately after configuration. Figure 19 shows the incoming and generated clock specifications. Figure 19. Specifications for Incoming & Generated Clocks The tI parameter refers to the nominal input clock period; the tO parameter refers to the nominal output clock period. tCLK1 tINDUTY tI fCLKDEV Input Clock tR tF tI tI tINCLKSTB tO tO + tJITTER tOUTDUTY ClockLockGenerated Clock Altera Corporation tO - tJITTER 39 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Tables 12 and 13 summarize the ClockLock and ClockBoost parameters for -1 and -2 speed-grade devices, respectively. Table 12. ClockLock & ClockBoost Parameters for -1 Speed-Grade Devices Max Unit tR Symbol Input rise time 5 ns tF Input fall time 5 ns t INDUTY Input duty cycle 40 60 % f CLK1 Input clock frequency (ClockBoost clock multiplication factor equals 1) 25 180 MHz fCLK2 Input clock frequency (ClockBoost clock multiplication factor equals 2) 16 90 MHz f CLKDEV Input deviation from user specification in the MAX+PLUS II software (1) 25,000 (2) PPM t INCLKSTB Input clock stability (measured between adjacent clocks) 100 ps t LOCK Time required for ClockLock or ClockBoost to acquire lock (3) 10 s t JITTER Jitter on ClockLock or ClockBoostgenerated clock (4) t INCLKSTB < 100 250 ps t INCLKSTB < 50 200 (4) ps 60 % tOUTDUTY 40 Parameter Duty cycle for ClockLock or ClockBoost-generated clock Condition Min 40 Typ 50 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 13. ClockLock & ClockBoost Parameters for -2 Speed-Grade Devices Symbol Parameter Condition Min Typ Max Unit tR Input rise time 5 ns tF Input fall time 5 ns t INDUTY Input duty cycle 40 60 % f CLK1 Input clock frequency (ClockBoost clock multiplication factor equals 1) 25 75 MHz fCLK2 Input clock frequency (ClockBoost clock multiplication factor equals 2) 16 37.5 MHz f CLKDEV Input deviation from user specification in the MAX+PLUS II software (1) 25,000 (2) PPM t INCLKSTB Input clock stability (measured between adjacent clocks) 100 ps t LOCK Time required for ClockLock or ClockBoost to acquire lock (3) 10 s t JITTER Jitter on ClockLock or ClockBoostgenerated clock (4) t INCLKSTB < 100 250 ps t INCLKSTB < 50 200 (4) ps 60 % tOUTDUTY Duty cycle for ClockLock or ClockBoost-generated clock 40 50 Notes to tables: (1) (2) (3) (4) To implement the ClockLock and ClockBoost circuitry with the MAX+PLUS II software, designers must specify the input frequency. The Altera software tunes the PLL in the ClockLock and ClockBoost circuitry to this frequency. The fCLKDEV parameter specifies how much the incoming clock can differ from the specified frequency during device operation. Simulation does not reflect this parameter. Twenty-five thousand parts per million (PPM) equates to 2.5% of input clock period. During device configuration, the ClockLock and ClockBoost circuitry is configured before the rest of the device. If the incoming clock is supplied during configuration, the ClockLock and ClockBoost circuitry locks during configuration because the tLOCK value is less than the time required for configuration. The tJITTER specification is measured under long-term observation. The maximum value for tJITTER is 200 ps if tINCLKSTB is lower than 50 ps. I/O Configuration Altera Corporation This section discusses the peripheral component interconnect (PCI) pull-up clamping diode option, slew-rate control, open-drain output option, and MultiVolt I/O interface for FLEX 10KE devices. The PCI pull-up clamping diode, slew-rate control, and open-drain output options are controlled pin-by-pin via Altera software logic options. The MultiVolt I/O interface is controlled by connecting VCCIO to a different voltage than VCCINT. Its effect can be simulated in the Altera software via the Global Project Device Options dialog box (Assign menu). 41 FLEX 10KE Embedded Programmable Logic Devices Data Sheet PCI Pull-Up Clamping Diode Option FLEX 10KE devices have a pull-up clamping diode on every I/O, dedicated input, and dedicated clock pin. PCI clamping diodes clamp the signal to the VCCIO value and are required for 3.3-V PCI compliance. Clamping diodes can also be used to limit overshoot in other systems. Clamping diodes are controlled on a pin-by-pin basis. When VCCIO is 3.3 V, a pin that has the clamping diode option turned on can be driven by a 2.5-V or 3.3-V signal, but not a 5.0-V signal. When VCCIO is 2.5 V, a pin that has the clamping diode option turned on can be driven by a 2.5-V signal, but not a 3.3-V or 5.0-V signal. Additionally, a clamping diode can be activated for a subset of pins, which would allow a device to bridge between a 3.3-V PCI bus and a 5.0-V device. Slew-Rate Control The output buffer in each IOE has an adjustable output slew rate that can be configured for low-noise or high-speed performance. A slower slew rate reduces system noise and adds a maximum delay of 4.3 ns. The fast slew rate should be used for speed-critical outputs in systems that are adequately protected against noise. Designers can specify the slew rate pin-by-pin or assign a default slew rate to all pins on a device-wide basis. The slow slew rate setting affects the falling edge of the output. Open-Drain Output Option FLEX 10KE devices provide an optional open-drain output (electrically equivalent to open-collector output) for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. It can also provide an additional wired-OR plane. MultiVolt I/O Interface The FLEX 10KE device architecture supports the MultiVolt I/O interface feature, which allows FLEX 10KE devices in all packages to interface with systems of differing supply voltages. These devices have one set of VCC pins for internal operation and input buffers (VCCINT), and another set for I/O output drivers (VCCIO). 42 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet The VCCINT pins must always be connected to a 2.5-V power supply. With a 2.5-V VCCINT level, input voltages are compatible with 2.5-V, 3.3V, and 5.0-V inputs. The VCCIO pins can be connected to either a 2.5-V or 3.3-V power supply, depending on the output requirements. When the VCCIO pins are connected to a 2.5-V power supply, the output levels are compatible with 2.5-V systems. When the VCCIO pins are connected to a 3.3-V power supply, the output high is at 3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices operating with VCCIO levels higher than 3.0 V achieve a faster timing delay of tOD2 instead of tOD1. Table 14 summarizes FLEX 10KE MultiVolt I/O support. Table 14. FLEX 10KE MultiVolt I/O Support VCCIO (V) Input Signal (V) 2.5 3.3 Output Signal (V) 5.0 2.5 2.5 v v(1) v(1) v 3.3 v v v(1) v(2) 3.3 5.0 v v Notes: (1) (2) The PCI clamping diode must be disabled to drive an input with voltages higher than VCCIO. When VCCIO = 3.3 V, a FLEX 10KE device can drive a 2.5-V device that has 3.3-V tolerant inputs. Open-drain output pins on FLEX 10KE devices (with a pull-up resistor to the 5.0-V supply) can drive 5.0-V CMOS input pins that require a VIH of 3.5 V. When the open-drain pin is active, it will drive low. When the pin is inactive, the trace will be pulled up to 5.0 V by the resistor. The open-drain pin will only drive low or tri-state; it will never drive high. The rise time is dependent on the value of the pull-up resistor and load impedance. The IOL current specification should be considered when selecting a pull-up resistor. Power Sequencing & Hot-Socketing Because FLEX 10KE devices can be used in a mixed-voltage environment, they have been designed specifically to tolerate any possible power-up sequence. The VCCIO and VCCINT power planes can be powered in any order. Signals can be driven into FLEX 10KE devices before and during power up without damaging the device. Additionally, FLEX 10KE devices do not drive out during power up. Once operating conditions are reached, FLEX 10KE devices operate as specified by the user. Altera Corporation 43 FLEX 10KE Embedded Programmable Logic Devices Data Sheet IEEE Std. 1149.1 (JTAG) Boundary-Scan Support All FLEX 10KE devices provide JTAG BST circuitry that complies with the IEEE Std. 1149.1-1990 specification. FLEX 10KE devices can also be configured using the JTAG pins through the BitBlaster or ByteBlasterMV download cable, or via hardware that uses the JamTM STAPL programming and test language. JTAG boundary-scan testing can be performed before or after configuration, but not during configuration. FLEX 10KE devices support the JTAG instructions shown in Table 15. Table 15. FLEX 10KE JTAG Instructions JTAG Instruction Description SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern to be output at the device pins. EXTEST Allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins. BYPASS Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through a selected device to adjacent devices during normal device operation. USERCODE Selects the user electronic signature (USERCODE) register and places it between the TDI and TDO pins, allowing the USERCODE to be serially shifted out of TDO. IDCODE Selects the IDCODE register and places it between TDI and TDO, allowing the IDCODE to be serially shifted out of TDO. ICR Instructions These instructions are used when configuring a FLEX 10KE device via JTAG ports with a BitBlaster or ByteBlasterMV download cable, or using a Jam File (.jam) or Jam Byte-Code File (.jbc) via an embedded processor. The instruction register length of FLEX 10KE devices is 10 bits. The USERCODE register length in FLEX 10KE devices is 32 bits; 7 bits are determined by the user, and 25 bits are pre-determined. Tables 16 and 17 show the boundary-scan register length and device IDCODE information for FLEX 10KE devices. Table 16. FLEX 10KE Boundary-Scan Register Length Device EPF10K30E 690 EPF10K50E EPF10K50S 798 EPF10K100E 44 Boundary-Scan Register Length 1,050 EPF10K130E 1,308 EPF10K200E EPF10K200S 1,446 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 17. 32-Bit IDCODE for FLEX 10KE Devices Device Note (1) IDCODE (32 Bits) Version (4 Bits) Part Number (16 Bits) Manufacturer's 1 (1 Bit) Identity (11 Bits) (2) EPF10K30E 0001 0001 0000 0011 0000 00001101110 1 EPF10K50E EPF10K50S 0001 0001 0000 0101 0000 00001101110 1 EPF10K100E 0010 0000 0001 0000 0000 00001101110 1 EPF10K130E 0001 0000 0001 0011 0000 00001101110 1 EPF10K200E EPF10K200S 0001 0000 0010 0000 0000 00001101110 1 Notes: (1) (2) The most significant bit (MSB) is on the left. The least significant bit (LSB) for all JTAG IDCODEs is 1. FLEX 10KE devices include weak pull-up resistors on the JTAG pins. f For more information, see the following documents: Altera Corporation Application Note 39 (IEEE Std. 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices) BitBlaster Serial Download Cable Data Sheet ByteBlasterMV Parallel Port Download Cable Data Sheet Jam Programming & Test Language Specification 45 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 20 shows the timing requirements for the JTAG signals. Figure 20. FLEX 10KE JTAG Waveforms TMS TDI t JCP t JCH t JCL t JPSU t JPH TCK tJPZX t JPXZ t JPCO TDO tJSH tJSSU Signal to Be Captured Signal to Be Driven tJSCO tJSZX tJSXZ Table 18 shows the timing parameters and values for FLEX 10KE devices. Table 18. FLEX 10KE JTAG Timing Parameters & Values Symbol 46 Parameter Min Max Unit tJCP TCK clock period 100 ns tJCH TCK clock high time 50 ns tJCL TCK clock low time 50 ns tJPSU JTAG port setup time 20 ns tJPH JTAG port hold time 45 ns tJPCO JTAG port clock to output 25 ns tJPZX JTAG port high impedance to valid output 25 ns tJPXZ JTAG port valid output to high impedance 25 tJSSU Capture register setup time 20 tJSH Capture register hold time 45 tJSCO Update register clock to output 35 ns tJSZX Update register high impedance to valid output 35 ns tJSXZ Update register valid output to high impedance 35 ns ns ns ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Generic Testing Each FLEX 10KE device is functionally tested. Complete testing of each configurable static random access memory (SRAM) bit and all logic functionality ensures 100% yield. AC test measurements for FLEX 10KE devices are made under conditions equivalent to those shown in Figure 21. Multiple test patterns can be used to configure devices during all stages of the production flow. Figure 21. FLEX 10KE AC Test Conditions Power supply transients can affect AC measurements. Simultaneous transitions of multiple outputs should be avoided for accurate measurement. Threshold tests must not be performed under AC conditions. Large-amplitude, fast-groundcurrent transients normally occur as the device outputs discharge the load capacitances. When these transients flow through the parasitic inductance between the device ground pin and the test system ground, significant reductions in observable noise immunity can result. Numbers in brackets are for 2.5-V devices or outputs. Numbers without brackets are for 3.3-V. devices or outputs. Operating Conditions Symbol 703 [481 ] Test System Device Output 8.06 k [481 ] C1 (includes JIG capacitance) Device input rise and fall times < 3 ns Tables 19 through 23 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for 2.5-V FLEX 10KE devices. Table 19. FLEX 10KE 2.5-V Device Absolute Maximum Ratings V CCINT VCCIO Parameter Supply voltage Note (1) Conditions With respect to ground (2) V CCIO Max Unit 3.6 V -0.5 4.6 V -2.0 5.75 V -25 25 mA -65 150 C -65 135 C PQFP, TQFP, BGA, and FineLine BGA packages, under bias 135 C Ceramic PGA packages, under bias 150 C VI DC input voltage I OUT DC output current, per pin T STG Storage temperature No bias T AMB Ambient temperature Under bias TJ Junction temperature Altera Corporation Min -0.5 47 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 20. 2.5-V EPF10K50E & EPF10K200E Device Recommended Operating Conditions Symbol Parameter Conditions Min Max Unit V CCINT Supply voltage for internal logic and input buffers (3), (4) 2.30 (2.30) 2.70 (2.70) V V CCIO Supply voltage for output buffers, (3), (4) 3.3-V operation 3.00 (3.00) 3.60 (3.60) V Supply voltage for output buffers, (3), (4) 2.5-V operation 2.30 (2.30) 2.70 (2.70) V VI Input voltage VO Output voltage TA Ambient temperature (5) For commercial use For industrial use -0.5 5.75 V 0 V CCIO V C 0 70 -40 85 C 0 85 C -40 TJ Operating temperature 100 C tR Input rise time 40 ns tF Input fall time 40 ns For commercial use For industrial use Table 21. 2.5-V EPF10K30E, EPF10K50S, EPF10K100E, EPF10K130E & EPF10K200S Device Recommended Operating Conditions Symbol Parameter Min Max Unit 2.375 (2.375) 2.625 (2.625) V Supply voltage for output buffers, (3), (4) 3.3-V operation 3.00 (3.00) 3.60 (3.60) V Supply voltage for output buffers, (3), (4) 2.5-V operation 2.375 (2.375) 2.625 (2.625) V V CCINT Supply voltage for internal logic and input buffers V CCIO Conditions (3), (4) VI Input voltage VO Output voltage (5) TA Ambient temperature For commercial use TJ Operating temperature For commercial use tR Input rise time tF Input fall time For industrial use For industrial use 48 -0.5 5.75 V 0 V CCIO V 0 70 C -40 85 C 0 85 C -40 100 C 40 ns 40 ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 22. FLEX 10KE 2.5-V Device DC Operating Conditions Symbol Parameter Conditions Notes (6), (7) Min Typ Max Unit V IH High-level input voltage 1.7, 0.5 x VCCIO (8) 5.75 V V IL Low-level input voltage -0.5 0.8, 0.3 x VCCIO (8) V V OH 3.3-V high-level TTL output voltage 2.4 V V CCIO - 0.2 V 0.9 x VCCIO V 2.5-V high-level output I OH = -0.1 mA DC, V CCIO = 2.30 V (9) voltage 2.1 V I OH = -1 mA DC, V CCIO = 2.30 V (9) 2.0 V I OH = -2 mA DC, V CCIO = 2.30 V (9) 1.7 V I OH = -8 mA DC, V CCIO = 3.00 V (9) 3.3-V high-level I OH = -0.1 mA DC, CMOS output voltage V CCIO = 3.00 V (9) 3.3-V high-level PCI output voltage V OL I OH = -0.5 mA DC, V CCIO = 3.00 to 3.60 V (9) I OL = 12 mA DC, V CCIO = 3.00 V (10) 0.45 V 3.3-V low-level CMOS I OL = 0.1 mA DC, V CCIO = 3.00 V (10) output voltage 0.2 V 0.1 x VCCIO V 2.5-V low-level output I OL = 0.1 mA DC, V CCIO = 2.30 V (10) voltage 0.2 V I OL = 1 mA DC, V CCIO = 2.30 V (10) 0.4 V I OL = 2 mA DC, V CCIO = 2.30 V (10) 0.7 V 3.3-V low-level TTL output voltage 3.3-V low-level PCI output voltage I OL = 1.5 mA DC, V CCIO = 3.00 to 3.60 V (10) II Input pin leakage current V I = V CCIOmax to 0 V (11) -10 10 A I OZ Tri-stated I/O pin leakage current VO = VCCIOmax to 0 V (11) -10 10 A I CC0 V CC supply current (standby) V I = ground, no load, no toggling inputs 5 mA V I = ground, no load, no toggling inputs (12) 10 mA R CONF Value of I/O pin pull- V CCIO = 3.0 V (13) up resistor before and V CCIO = 2.3 V (13) during configuration Altera Corporation 20 50 k3/4 30 80 k3/4 49 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 23. FLEX 10KE Device Capacitance Symbol Parameter Note (14) Conditions Min Max Unit CIN Input capacitance VIN = 0 V, f = 1.0 MHz 10 pF CINCLK Input capacitance on dedicated clock pin VIN = 0 V, f = 1.0 MHz 12 pF COUT Output capacitance VOUT = 0 V, f = 1.0 MHz 10 pF Notes to tables: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) 50 See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input voltage is -0.5 V. During transitions, the inputs may undershoot to -2.0 V for input currents less than 100 mA and periods shorter than 20 ns. Numbers in parentheses are for industrial-temperature-range devices. Maximum V CC rise time is 100 ms, and VCC must rise monotonically. All pins, including dedicated inputs, clock, I/O, and JTAG pins, may be driven before VCCINT and VCCIO are powered. Typical values are for T A = 25 C, V CCINT = 2.5 V, and V CCIO = 2.5 V or 3.3 V. These values are specified under the FLEX 10KE Recommended Operating Conditions shown in Tables 20 and 21. The FLEX 10KE input buffers are compatible with 2.5-V, 3.3-V (LVTTL and LVCMOS), and 5.0-V TTL and CMOS signals. Additionally, the input buffers are 3.3-V PCI compliant when VCCIO and VCCINT meet the relationship shown in Figure 22. The IOH parameter refers to high-level TTL, PCI, or CMOS output current. The IOL parameter refers to low-level TTL, PCI, or CMOS output current. This parameter applies to open-drain pins as well as output pins. This value is specified for normal device operation. The value may vary during power-up. This parameter applies to -1 speed-grade commercial-temperature devices and -2 speed-grade-industrial temperature devices. Pin pull-up resistance values will be lower if the pin is driven higher than V CCIO by an external source. Capacitance is sample-tested only. Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 22 shows the required relationship between VCCIO and VCCINT for 3.3-V PCI compliance. Figure 22. Relationship between VCCIO & VCCINT for 3.3-V PCI Compliance 2.7 V CCINT (V) II PCI-Compliant Region 2.5 2.3 3.0 3.1 3.3 3.6 VCCIO IO (V) Figure 23 shows the typical output drive characteristics of FLEX 10KE devices with 3.3-V and 2.5-V VCCIO. The output driver is compliant to the 3.3-V PCI Local Bus Specification, Revision 2.2 (when VCCIO pins are connected to 3.3 V). FLEX 10KE devices with a -1 speed grade also comply with the drive strength requirements of the PCI Local Bus Specification, Revision 2.2 (when VCCINT pins are powered with a minimum supply of 2.375 V, and VCCIO pins are connected to 3.3 V). Therefore, these devices can be used in open 5.0-V PCI systems. Altera Corporation 51 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 23. Output Drive Characteristics of FLEX 10KE Devices 90 90 IOL 80 80 70 70 60 Typical IO Output Current (mA) Note (1) VCCINT = 2.5 V VCCIO = 2.5 V Room Temperature 50 40 30 IOL 60 Typical IO Output Current (mA) VCCINT = 2.5 V VCCIO = 3.3 V Room Temperature 50 40 30 IOH IOH 20 20 10 10 1 2 VO Output Voltage (V) 3 1 2 3 VO Output Voltage (V) Note: (1) These are transient (AC) currents. Timing Model The continuous, high-performance FastTrack Interconnect routing resources ensure predictable performance and accurate simulation and timing analysis. This predictable performance contrasts with that of FPGAs, which use a segmented connection scheme and therefore have unpredictable performance. Device performance can be estimated by following the signal path from a source, through the interconnect, to the destination. For example, the registered performance between two LEs on the same row can be calculated by adding the following parameters: LE register clock-to-output delay (tCO) Interconnect delay (tSAMEROW) LE look-up table delay (tLUT ) LE register setup time (tSU) The routing delay depends on the placement of the source and destination LEs. A more complex registered path may involve multiple combinatorial LEs between the source and destination LEs. 52 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Timing simulation and delay prediction are available with the Altera Simulator and Timing Analyzer, or with industry-standard EDA tools. The Simulator offers both pre-synthesis functional simulation to evaluate logic design accuracy and post-synthesis timing simulation with 0.1-ns resolution. The Timing Analyzer provides point-to-point timing delay information, setup and hold time analysis, and device-wide performance analysis. Figure 24 shows the overall timing model, which maps the possible paths to and from the various elements of the FLEX 10KE device. Figure 24. FLEX 10KE Device Timing Model Dedicated Clock/Input Interconnect Logic Element I/O Element Embedded Array Block Figures 25 through 28 show the delays that correspond to various paths and functions within the LE, IOE, EAB, and bidirectional timing models. Altera Corporation 53 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 25. FLEX 10KE Device LE Timing Model Cascade-In Carry-In Register Delays LUT Delay Data-In tLUT tRLUT t CO tCOMB t SU tH tPRE tCLR tCLUT Packed Register Delay tPACKED Data-Out Register Control Delay Control-In tC tEN Carry Chain Delay tCGENR tCASC tCGEN tCICO tLABCARRY Carry-Out 54 tLABCASC Cascade-Out Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 26. FLEX 10KE Device IOE Timing Model Output Data Delay I/O Register Delays tIOD tIOCO tIOCOMB tIOSU tIOH tIOCLR Data-In I/O Element Contol Delay Clock Enable Clear Clock Output Enable Output Delays tOD1 tOD2 tOD3 tXZ tZX1 tZX2 tZX3 tIOC tINREG Input Register Delay I/O Register Feedback Delay Data Feedback into FastTrack Interconnect tIOFD Input Delay tINCOMB Figure 27. FLEX 10KE Device EAB Timing Model EAB Data Input Delays Input Register Delays RAM/ROM Block Delays Output Register Delays tEABDATA1 tEABDATA2 tEABCO tEABBYPASS tEABSU tEABH tEABCH tEABCL tAA tDD tWP tWDSU tWDH tWASU tWAH tWO tRP tRASU tRAH tEABCO tEABBYPASS tEABSU tEABH tEABCH tEABCL Data-In Address Write Enable Input Delays WE Input Register Clock Output Register Clock tEABWE1 tEABWE2 EAB Clock Delay EAB Output Delay tEABOUT Data-Out tEABCLK Read Enable Input Delays RE Altera Corporation tEABRE1 tEABRE2 55 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 28. Synchronous Bidirectional Pin External Timing Model OE Register D Dedicated Clock PRN Q tXZBIDIR tZXBIDIR CLRN tOUTCOBIDIR Output Register D PRN Q CLRN Bidirectional Pin tINSUBIDIR tINHBIDIR Input Register PRN D Q CLRN Tables 24 through 28 describe the FLEX 10KE device internal timing parameters. Tables 29 through 30 describe the FLEX 10KE external timing parameters and their symbols. Table 24. LE Timing Microparameters (Part 1 of 2) Symbol Note (1) Parameter tLUT LUT delay for data-in tCLUT LUT delay for carry-in tRLUT LUT delay for LE register feedback tPACKED Data-in to packed register delay tEN LE register enable delay tCICO Carry-in to carry-out delay tCGEN Data-in to carry-out delay tCGENR LE register feedback to carry-out delay tCASC Cascade-in to cascade-out delay tC LE register control signal delay tCO LE register clock-to-output delay tCOMB Combinatorial delay tSU LE register setup time for data and enable signals before clock; LE register recovery time after asynchronous clear, preset, or load tH LE register hold time for data and enable signals after clock tPRE LE register preset delay 56 Condition Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 24. LE Timing Microparameters (Part 2 of 2) Symbol Note (1) Parameter tCLR LE register clear delay tCH Minimum clock high time from clock pin tCL Minimum clock low time from clock pin Table 25. IOE Timing Microparameters Condition Note (1) Symbol Parameter Conditions tIOD IOE data delay tIOC IOE register control signal delay tIOCO IOE register clock-to-output delay tIOCOMB IOE combinatorial delay tIOSU IOE register setup time for data and enable signals before clock; IOE register recovery time after asynchronous clear tIOH IOE register hold time for data and enable signals after clock tIOCLR IOE register clear time tOD1 Output buffer and pad delay, slow slew rate = off, VCCIO = 3.3 V C1 = 35 pF (2) tOD2 Output buffer and pad delay, slow slew rate = off, VCCIO = 2.5 V C1 = 35 pF (3) tOD3 Output buffer and pad delay, slow slew rate = on C1 = 35 pF (4) tXZ IOE output buffer disable delay tZX1 IOE output buffer enable delay, slow slew rate = off, VCCIO = 3.3 V tZX2 IOE output buffer enable delay, slow slew rate = off, VCCIO = 2.5 V C1 = 35 pF (3) tZX3 IOE output buffer enable delay, slow slew rate = on C1 = 35 pF (4) tINREG IOE input pad and buffer to IOE register delay tIOFD IOE register feedback delay tINCOMB IOE input pad and buffer to FastTrack Interconnect delay Altera Corporation C1 = 35 pF (2) 57 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 26. EAB Timing Microparameters Note (1) Symbol Parameter Conditions tEABDATA1 Data or address delay to EAB for combinatorial input tEABDATA2 Data or address delay to EAB for registered input tEABWE1 Write enable delay to EAB for combinatorial input tEABWE2 Write enable delay to EAB for registered input tEABRE1 Read enable delay to EAB for combinatorial input tEABRE2 Read enable delay to EAB for registered input tEABCLK EAB register clock delay tEABCO EAB register clock-to-output delay tEABBYPASS Bypass register delay tEABSU EAB register setup time before clock tEABH EAB register hold time after clock tEABCLR EAB register asynchronous clear time to output delay tAA Address access delay (including the read enable to output delay) tWP Write pulse width tRP Read pulse width tWDSU Data setup time before falling edge of write pulse (5) tWDH Data hold time after falling edge of write pulse (5) tWASU Address setup time before rising edge of write pulse (5) tWAH Address hold time after falling edge of write pulse (5) tRASU Address setup time with respect to the falling edge of the read enable tRAH Address hold time with respect to the falling edge of the read enable tWO Write enable to data output valid delay tDD Data-in to data-out valid delay tEABOUT Data-out delay tEABCH Clock high time tEABCL Clock low time 58 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 27. EAB Timing Macroparameters Symbol Note (1), (6) Parameter tEABAA EAB address access delay tEABRCCOMB EAB asynchronous read cycle time tEABRCREG EAB synchronous read cycle time tEABWP EAB write pulse width tEABWCCOMB EAB asynchronous write cycle time tEABWCREG EAB synchronous write cycle time tEABDD EAB data-in to data-out valid delay tEABDATACO EAB clock-to-output delay when using output registers tEABDATASU EAB data/address setup time before clock when using input register tEABDATAH EAB data/address hold time after clock when using input register tEABWESU EAB WE setup time before clock when using input register tEABWEH EAB WE hold time after clock when using input register tEABWDSU EAB data setup time before falling edge of write pulse when not using input registers tEABWDH EAB data hold time after falling edge of write pulse when not using input registers tEABWASU EAB address setup time before rising edge of write pulse when not using input registers tEABWAH EAB address hold time after falling edge of write pulse when not using input registers tEABWO EAB write enable to data output valid delay Altera Corporation Conditions 59 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 28. Interconnect Timing Microparameters Symbol Note (1) Parameter Conditions tDIN2IOE Delay from dedicated input pin to IOE control input (7) tDIN2LE Delay from dedicated input pin to LE or EAB control input (7) tDCLK2IOE Delay from dedicated clock pin to IOE clock (7) tDCLK2LE Delay from dedicated clock pin to LE or EAB clock (7) tDIN2DATA Delay from dedicated input or clock to LE or EAB data (7) tSAMELAB Routing delay for an LE driving another LE in the same LAB tSAMEROW Routing delay for a row IOE, LE, or EAB driving a row IOE, LE, or EAB in the (7) same row tSAMECOLUMN Routing delay for an LE driving an IOE in the same column tDIFFROW Routing delay for a column IOE, LE, or EAB driving an LE or EAB in a different (7) row tTWOROWS Routing delay for a row IOE or EAB driving an LE or EAB in a different row (7) tLEPERIPH Routing delay for an LE driving a control signal of an IOE via the peripheral control bus (7) tLABCARRY Routing delay for the carry-out signal of an LE driving the carry-in signal of a different LE in a different LAB tLABCASC Routing delay for the cascade-out signal of an LE driving the cascade-in signal of a different LE in a different LAB (7) Table 29. External Timing Parameters Symbol Parameter Conditions tDRR Register-to-register delay via four LEs, three row interconnects, and four local (8) interconnects tINSU Setup time with global clock at IOE register (9) tINH Hold time with global clock at IOE register (9) tOUTCO Clock-to-output delay with global clock at IOE register (9) tPCISU Setup time with global clock for registers used in PCI designs (9),(10) tPCIH Hold time with global clock for registers used in PCI designs (9),(10) tPCICO Clock-to-output delay with global clock for registers used in PCI designs (9),(10) 60 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 30. External Bidirectional Timing Parameters Symbol Note (9) Parameter Conditions tINSUBIDIR Setup time for bi-directional pins with global clock at same-row or samecolumn LE register tINHBIDIR Hold time for bidirectional pins with global clock at same-row or same-column LE register tINH Hold time with global clock at IOE register tOUTCOBIDIR Clock-to-output delay for bidirectional pins with global clock at IOE register C1 = 35 pF tXZBIDIR Synchronous IOE output buffer disable delay C1 = 35 pF tZXBIDIR Synchronous IOE output buffer enable delay, slow slew rate= off C1 = 35 pF Notes to tables: (1) Microparameters are timing delays contributed by individual architectural elements. These parameters cannot be measured explicitly. (2) Operating conditions: VCCIO = 3.3 V 10% for commercial or industrial use. (3) Operating conditions: VCCIO = 2.5 V 5% for commercial or industrial use in EPF10K30E, EPF10K50S, EPF10K100E, EPF10K130E, and EPF10K200S devices. (4) Operating conditions: VCCIO = 3.3 V. (5) Because the RAM in the EAB is self-timed, this parameter can be ignored when the WE signal is registered. (6) EAB macroparameters are internal parameters that can simplify predicting the behavior of an EAB at its boundary; these parameters are calculated by summing selected microparameters. (7) These parameters are worst-case values for typical applications. Post-compilation timing simulation and timing analysis are required to determine actual worst-case performance. (8) Contact Altera Applications for test circuit specifications and test conditions. (9) This timing parameter is sample-tested only. (10) This parameter is measured with the measurement and test conditions, including load, specified in the PCI Local Bus Specification, revision 2.2. Altera Corporation 61 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figures 29 and 30 show the asynchronous and synchronous timing waveforms, respectively, or the EAB macroparameters in Tables 26 and 27. Figure 29. EAB Asynchronous Timing Waveforms EAB Asynchronous Read WE a0 Address a1 a2 tEABAA Data-Out a3 tEABRCCOMB d0 d1 d3 d2 EAB Asynchronous Write WE tEABWP tEABWDSU din0 Data-In tEABWDH din1 tEABWASU tEABWAH tEABWCCOMB Address a0 a1 a2 tEABDD Data-Out 62 din0 din1 dout2 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 30. EAB Synchronous Timing Waveforms EAB Synchronous Read WE Address a0 a1 tEABDATASU a2 a3 tEABRCREG tEABDATAH CLK tEABDATACO Data-Out d2 d1 EAB Synchronous Write (EAB Output Registers Used) WE Data-In Address a0 din1 din2 din3 a1 a2 a3 tEABWESU tEABDATASU tEABDATAH a2 tEABWEH CLK tEABDATACO tEABWCREG dout0 Data-Out dout1 din1 din2 din3 din2 Tables 31 through 37 show EPF10K30E device internal and external timing parameters. Table 31. EPF10K30E Device LE Timing Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.7 0.8 1.1 ns tCLUT 0.5 0.6 0.8 ns tRLUT 0.6 0.7 1.0 ns tPACKED 0.3 0.4 0.5 ns tEN 0.6 0.8 1.0 ns tCICO 0.1 0.1 0.2 ns tCGEN 0.4 0.5 0.7 ns Altera Corporation 63 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 31. EPF10K30E Device LE Timing Microparameters (Part 2 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tCGENR 0.1 0.1 0.2 ns tCASC 0.6 0.8 1.0 ns tC 0.0 0.0 0.0 ns tCO 0.3 0.4 0.5 ns tCOMB 0.4 0.4 0.6 ns tSU 0.4 0.6 0.6 tH 0.7 1.0 1.3 0.8 tPRE tCLR 0.9 0.8 0.9 ns ns 1.2 ns 1.2 ns tCH 2.0 2.5 2.5 ns tCL 2.0 2.5 2.5 ns Table 32. EPF10K30E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 2.4 2.8 3.8 ns tIOC 0.3 0.4 0.5 ns tIOCO 1.0 1.1 1.6 ns tIOCOMB 0.0 0.0 0.0 ns tIOSU 1.2 1.4 1.9 ns tIOH 0.3 0.4 0.5 ns tIOCLR 1.0 1.1 1.6 ns tOD1 1.9 2.3 3.0 ns tOD2 1.4 1.8 2.5 ns tOD3 4.4 5.2 7.0 ns tXZ 2.7 3.1 4.3 ns tZX1 2.7 3.1 4.3 ns tZX2 2.2 2.6 3.8 ns tZX3 5.2 6.0 8.3 ns tINREG 3.4 4.1 5.5 ns tIOFD 0.8 1.3 2.4 ns tINCOMB 0.8 1.3 2.4 ns 64 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 33. EPF10K30E Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.7 2.0 2.3 ns tEABDATA1 0.6 0.7 0.8 ns tEABWE1 1.1 1.3 1.4 ns tEABWE2 0.4 0.4 0.5 ns tEABRE1 0.8 0.9 1.0 ns tEABRE2 0.4 0.4 0.5 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.3 0.3 0.4 ns 0.7 ns tEABBYPASS 0.5 0.6 tEABSU 0.9 1.0 1.2 ns tEABH 0.4 0.4 0.5 ns tEABCLR 0.3 0.3 0.3 tAA 3.2 3.8 ns 4.4 ns tWP 2.5 2.9 3.3 ns tRP 0.9 1.1 1.2 ns tWDSU 0.9 1.0 1.1 ns tWDH 0.1 0.1 0.1 ns tWASU 1.7 2.0 2.3 ns tWAH 1.8 2.1 2.4 ns tRASU 3.1 3.7 4.2 ns tRAH 0.2 0.2 0.2 ns tWO 2.5 2.9 3.3 ns tDD 2.5 2.9 3.3 ns tEABOUT 0.5 0.6 0.7 ns tEABCH 1.5 2.0 2.3 ns tEABCL 2.5 2.9 3.3 ns Altera Corporation 65 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 34. EPF10K30E Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 6.4 Max 7.6 Unit Max 8.8 ns tEABRCOMB 6.4 7.6 8.8 ns tEABRCREG 4.4 5.1 6.0 ns tEABWP 2.5 2.9 3.3 ns tEABWCOMB 6.0 7.0 8.0 ns tEABWCREG 6.8 7.8 9.0 ns tEABDD 5.7 6.7 7.7 ns tEABDATACO 0.8 0.9 1.1 ns tEABDATASU 1.5 1.7 2.0 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 1.3 1.4 1.7 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.5 1.7 2.0 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 3.0 3.6 4.3 ns tEABWAH 0.5 0.5 0.4 tEABWO 66 5.1 6.0 ns 6.8 ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 35. EPF10K30E Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 1.8 2.4 2.9 ns tDIN2LE 1.5 1.8 2.4 ns tDIN2DATA 1.5 1.8 2.2 ns tDCLK2IOE 2.2 2.6 3.0 ns tDCLK2LE 1.5 1.8 2.4 ns tSAMELAB 0.1 0.2 0.3 ns tSAMEROW 2.0 2.4 2.7 ns tSAMECOLUMN 0.7 1.0 0.8 ns tDIFFROW 2.7 3.4 3.5 ns tTWOROWS 4.7 5.8 6.2 ns tLEPERIPH 2.7 3.4 3.8 ns tLABCARRY 0.3 0.4 0.5 ns tLABCASC 0.8 0.8 1.1 ns Table 36. EPF10K30E External Timing Parameters Symbol Notes (1), (2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 8.0 Max 9.5 Unit Max 12.5 ns tINSU (3) 2.1 2.5 3.9 ns tINH (3) 0.0 0.0 0.0 ns tOUTCO (3) 2.0 tINSU (4) 1.1 tINH (4) 0.0 tOUTCO (4) 0.5 tPCISU 3.0 tPCIH 0.0 tPCICO 2.0 Altera Corporation 4.9 2.0 5.9 1.5 0.5 ns - - 0.0 2.0 - - ns ns - 7.5 ns ns - 4.9 4.2 6.0 7.6 - 0.0 3.9 2.0 ns - ns 67 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 37. EPF10K30E External Bidirectional Timing Parameters Symbol Notes (1), (2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tINSUBIDIR (3) 2.8 3.9 5.2 ns tINHBIDIR (3) 0.0 0.0 0.0 ns tINSUBIDIR (4) 3.8 4.9 - ns tINHBIDIR (4) 0.0 0.0 - ns tOUTCOBIDIR (3) 2.0 tXZBIDIR (3) 2.0 6.1 tZXBIDIR (3) tOUTCOBIDIR (4) 4.9 3.9 2.0 7.5 6.1 0.5 5.9 7.5 0.5 4.9 7.6 ns 9.7 ns 9.7 ns - ns - tXZBIDIR (4) 5.1 6.5 - ns tZXBIDIR (4) 5.1 6.5 - ns Notes to tables: (1) (2) (3) (4) All timing parameters are described in Tables 24 through 30 in this data sheet. These parameters are specified by characterization. This parameter is measured without the use of the ClockLock or ClockBoost circuits. This parameter is measured with the use of the ClockLock or ClockBoost circuits. Tables 38 through 44 show EPF10K50E device internal and external timing parameters. Table 38. EPF10K50E Device LE Timing Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.6 0.9 1.3 ns tCLUT 0.5 0.6 0.8 ns tRLUT 0.7 0.8 1.1 ns tPACKED 0.4 0.5 0.6 ns tEN 0.6 0.7 0.9 ns tCICO 0.2 0.2 0.3 ns tCGEN 0.5 0.5 0.8 ns tCGENR 0.2 0.2 0.3 ns tCASC 0.8 1.0 1.4 ns tC 0.5 0.6 0.8 ns tCO 0.7 0.7 0.9 ns tCOMB 0.5 0.6 0.8 ns tSU 68 0.7 0.7 0.8 ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 38. EPF10K50E Device LE Timing Microparameters (Part 2 of 2) Symbol tH Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max 0.9 Max 1.0 Unit Max 1.4 ns tPRE 0.5 0.6 0.8 ns tCLR 0.5 0.6 0.8 ns tCH 2.0 2.5 3.0 ns tCL 2.0 2.5 3.0 ns Table 39. EPF10K50E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 2.2 2.4 3.3 ns tIOC 0.3 0.3 0.5 ns tIOCO 1.0 1.0 1.4 ns tIOCOMB 0.0 0.0 0.2 tIOSU 1.0 tIOH 0.3 1.2 1.7 0.3 ns ns 0.5 ns tIOCLR 0.9 1.0 1.4 ns tOD1 0.8 0.9 1.2 ns tOD2 0.3 0.4 0.7 ns tOD3 3.0 3.5 3.5 ns tXZ 1.4 1.7 2.3 ns tZX1 1.4 1.7 2.3 ns tZX2 0.9 1.2 1.8 ns tZX3 3.6 4.3 4.6 ns tINREG 4.9 5.8 7.8 ns tIOFD 2.8 3.3 4.5 ns tINCOMB 2.8 3.3 4.5 ns Altera Corporation 69 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 40. EPF10K50E Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.7 2.0 2.7 ns tEABDATA1 0.6 0.7 0.9 ns tEABWE1 1.1 1.3 1.8 ns tEABWE2 0.4 0.4 0.6 ns tEABRE1 0.8 0.9 1.2 ns tEABRE2 0.4 0.4 0.6 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.3 0.3 0.5 ns 0.8 ns tEABBYPASS 0.5 0.6 tEABSU 0.9 1.0 1.4 tEABH 0.4 0.4 0.6 ns tEABCLR 0.3 0.3 0.5 ns tAA 3.2 3.8 ns 5.1 ns tWP 2.5 2.9 3.9 ns tRP 0.9 1.1 1.5 ns tWDSU 0.9 1.0 1.4 ns tWDH 0.1 0.1 0.2 ns tWASU 1.7 2.0 2.7 ns tWAH 1.8 2.1 2.9 ns tRASU 3.1 3.7 5.0 ns tRAH 0.2 0.2 0.3 ns tWO 2.5 2.9 3.9 ns tDD 2.5 2.9 3.9 ns tEABOUT 0.5 0.6 0.8 ns tEABCH 1.5 2.0 2.5 ns tEABCL 2.5 2.9 3.9 ns 70 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 41. EPF10K50E Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 6.4 Max 7.6 Unit Max 10.2 ns tEABRCOMB 6.4 7.6 10.2 ns tEABRCREG 4.4 5.1 7.0 ns tEABWP 2.5 2.9 3.9 ns tEABWCOMB 6.0 7.0 9.5 ns tEABWCREG 6.8 7.8 10.6 ns tEABDD 5.7 6.7 9.0 ns tEABDATACO 0.8 0.9 1.3 ns tEABDATASU 1.5 1.7 2.3 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 1.3 1.4 2.0 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.5 1.7 2.3 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 3.0 3.6 4.8 ns tEABWAH 0.5 0.5 0.8 tEABWO 5.1 6.0 Table 42. EPF10K50E Device Interconnect Timing Microparameters Symbol ns 8.1 Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Unit Max tDIN2IOE 3.5 4.3 5.6 ns tDIN2LE 2.1 2.5 3.4 ns tDIN2DATA 2.2 2.4 3.1 ns tDCLK2IOE 2.9 3.5 4.7 ns tDCLK2LE 2.1 2.5 3.4 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 1.1 1.1 1.5 ns tSAMECOLUMN 0.8 1.0 1.3 ns tDIFFROW 1.9 2.1 2.8 ns tTWOROWS 3.0 3.2 4.3 ns tLEPERIPH 3.1 3.3 3.7 ns tLABCARRY 0.1 0.1 0.2 ns tLABCASC 0.3 0.3 0.5 ns Altera Corporation 71 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 43. EPF10K50E External Timing Parameters Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 8.5 tINSU Notes (1), (2) 2.7 tINH 0.0 tOUTCO 2.0 tPCISU 3.0 tPCIH 0.0 tPCICO 2.0 Max 10.0 4.3 0.0 4.5 2.0 2.0 2.0 - ns - -2 Speed Grade -3 Speed Grade Min Min Min Max tINSUBIDIR 2.7 3.2 4.3 tINHBIDIR 0.0 0.0 0.0 tOUTCOBIDIR 2.0 4.5 2.0 5.2 ns Notes (1), (2) -1 Speed Grade Max ns ns 7.7 Table 44. EPF10K50E External Bidirectional Timing Parameters Symbol ns 7.3 - 0.0 ns ns 0.0 5.2 4.2 6.0 Max 13.5 3.2 Unit 2.0 Unit Max ns ns 7.3 ns tXZBIDIR 6.8 7.8 10.1 ns tZXBIDIR 6.8 7.8 10.1 ns Notes to tables: (1) (2) All timing parameters are described in Tables 24 through 30 in this data sheet. These parameters are specified by characterization. Tables 45 through 51 show EPF10K100E device internal and external timing parameters. Table 45. EPF10K100E Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.7 1.0 1.5 ns tCLUT 0.5 0.7 0.9 ns tRLUT 0.6 0.8 1.1 ns tPACKED 0.3 0.4 0.5 ns tEN 0.2 0.3 0.3 ns tCICO 0.1 0.1 0.2 ns tCGEN 0.4 0.5 0.7 ns 72 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 45. EPF10K100E Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tCGENR 0.1 0.1 0.2 ns tCASC 0.6 0.9 1.2 ns tC 0.8 1.0 1.4 ns tCO 0.6 0.8 1.1 ns tCOMB 0.4 0.5 0.7 ns tSU 0.4 0.6 0.7 ns tH 0.5 0.7 0.9 ns 0.8 tPRE tCLR 1.0 0.8 1.4 1.0 1.4 ns ns tCH 1.5 2.0 2.5 ns tCL 1.5 2.0 2.5 ns Table 46. EPF10K100E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.7 2.0 2.6 ns tIOC 0.0 0.0 0.0 ns tIOCO 1.4 1.6 2.1 ns tIOCOMB 0.5 0.7 0.9 ns tIOSU 0.8 1.0 1.3 tIOH 0.7 0.9 1.2 ns ns tIOCLR 0.5 0.7 0.9 ns tOD1 3.0 4.2 5.6 ns tOD2 3.0 4.2 5.6 ns tOD3 4.0 5.5 7.3 ns tXZ 3.5 4.6 6.1 ns tZX1 3.5 4.6 6.1 ns tZX2 3.5 4.6 6.1 ns tZX3 4.5 5.9 7.8 ns tINREG 2.0 2.6 3.5 ns tIOFD 0.5 0.8 1.2 ns tINCOMB 0.5 0.8 1.2 ns Altera Corporation 73 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 47. EPF10K100E Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.5 2.0 2.6 ns tEABDATA1 0.0 0.0 0.0 ns tEABWE1 1.5 2.0 2.6 ns tEABWE2 0.3 0.4 0.5 ns tEABRE1 0.3 0.4 0.5 ns tEABRE2 0.0 0.0 0.0 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.3 0.4 0.5 ns 0.2 ns tEABBYPASS 0.1 0.1 tEABSU 0.8 1.0 1.4 tEABH 0.1 0.1 0.2 ns tEABCLR 0.3 0.4 0.5 ns tAA 4.0 5.1 ns 6.6 ns tWP 2.7 3.5 4.7 ns tRP 1.0 1.3 1.7 ns tWDSU 1.0 1.3 1.7 ns tWDH 0.2 0.2 0.3 ns tWASU 1.6 2.1 2.8 ns tWAH 1.6 2.1 2.8 ns tRASU 3.0 3.9 5.2 ns tRAH 0.1 0.1 0.2 ns tWO 1.5 2.0 2.6 ns tDD 1.5 2.0 2.6 ns tEABOUT 0.2 0.3 0.3 ns tEABCH 1.5 2.0 2.5 ns tEABCL 2.7 3.5 4.7 ns Table 48. EPF10K100E Device EAB Internal Timing Macroparameters (Part 1 of 2) Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 5.9 Max 7.6 Note (1) Unit Max 9.9 ns tEABRCOMB 5.9 7.6 9.9 ns tEABRCREG 5.1 6.5 8.5 ns tEABWP 2.7 3.5 4.7 ns 74 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 48. EPF10K100E Device EAB Internal Timing Macroparameters (Part 2 of 2) Symbol -1 Speed Grade -2 Speed Grade Min Min Max Max -3 Speed Grade Min Note (1) Unit Max tEABWCOMB 5.9 7.7 10.3 ns tEABWCREG 5.4 7.0 9.4 ns 3.4 tEABDD tEABDATACO 4.5 0.5 5.9 0.7 0.8 ns ns tEABDATASU 0.8 1.0 1.4 ns tEABDATAH 0.1 0.1 0.2 ns tEABWESU 1.1 1.4 1.9 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.0 1.3 1.7 ns tEABWDH 0.2 0.2 0.3 ns tEABWASU 4.1 5.2 6.8 ns tEABWAH 0.0 0.0 0.0 tEABWO 3.4 4.5 Table 49. EPF10K100E Device Interconnect Timing Microparameters Symbol ns 5.9 Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Unit Max tDIN2IOE 3.1 3.6 4.4 ns tDIN2LE 0.3 0.4 0.5 ns tDIN2DATA 1.6 1.8 2.0 ns tDCLK2IOE 0.8 1.1 1.4 ns tDCLK2LE 0.3 0.4 0.5 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 1.5 2.5 3.4 ns tSAMECOLUMN 0.4 1.0 1.6 ns tDIFFROW 1.9 3.5 5.0 ns tTWOROWS 3.4 6.0 8.4 ns tLEPERIPH 4.3 5.4 6.5 ns tLABCARRY 0.5 0.7 0.9 ns tLABCASC 0.8 1.0 1.4 ns Altera Corporation 75 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 50. EPF10K100E External Timing Parameters Symbol Notes (1), (2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 9.0 tINSU (3) 2.0 tINH (3) 0.0 tOUTCO (3) 2.0 tINSU (4) 2.0 tINH (4) 0.0 tOUTCO (4) 0.5 tPCISU 3.0 tPCIH 0.0 tPCICO 2.0 Max 12.0 2.5 2.0 6.2 2.0 ns - - ns - - ns Notes (1), (2) -2 Speed Grade -3 Speed Grade Min Min Min Max ns ns -1 Speed Grade Max ns ns - 6.9 Table 51. EPF10K100E External Bidirectional Timing Parameters Symbol 9.1 - 0.0 6.0 ns 2.0 - 4.6 ns ns - 0.0 0.5 16.0 0.0 6.9 2.2 3.0 Max 3.3 0.0 5.2 Unit Unit Max tINSUBIDIR (3) 1.7 2.5 3.3 ns tINHBIDIR (3) 0.0 0.0 0.0 ns tINSUBIDIR (4) 2.0 2.8 - ns tINHBIDIR (4) 0.0 0.0 - ns tOUTCOBIDIR (3) 2.0 5.2 2.0 6.9 2.0 9.1 ns ns tXZBIDIR (3) 5.6 7.5 10.1 tZXBIDIR (3) 5.6 7.5 10.1 ns - ns tOUTCOBIDIR (4) 0.5 3.0 0.5 4.6 - tXZBIDIR (4) 4.6 6.5 - ns tZXBIDIR (4) 4.6 6.5 - ns Notes to tables: (1) (2) (3) (4) 76 All timing parameters are described in Tables 24 through 30 in this data sheet. These parameters are specified by characterization. This parameter is measured without the use of the ClockLock or ClockBoost circuits. This parameter is measured with the use of the ClockLock or ClockBoost circuits. Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Tables 52 through 58 show EPF10K130E device internal and external timing parameters. Table 52. EPF10K130E Device LE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.6 0.9 1.3 ns tCLUT 0.6 0.8 1.0 ns tRLUT 0.7 0.9 0.2 ns tPACKED 0.3 0.5 0.6 ns tEN 0.2 0.3 0.4 ns tCICO 0.1 0.1 0.2 ns tCGEN 0.4 0.6 0.8 ns tCGENR 0.1 0.1 0.2 ns tCASC 0.6 0.9 1.2 ns tC 0.3 0.5 0.6 ns tCO 0.5 0.7 0.8 ns 0.6 ns 0.3 tCOMB 0.5 tSU 0.5 0.7 0.8 ns tH 0.6 0.7 1.0 ns tPRE 0.9 1.2 1.6 tCLR 0.9 1.2 1.6 ns ns tCH 1.5 1.5 2.5 ns tCL 1.5 1.5 2.5 ns Table 53. EPF10K130E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.3 1.5 2.0 ns tIOC 0.0 0.0 0.0 ns tIOCO 0.6 0.8 1.0 ns tIOCOMB 0.6 0.8 1.0 ns tIOSU 1.0 1.2 1.6 ns tIOH 0.9 0.9 1.4 ns tIOCLR 0.6 0.8 1.0 ns tOD1 2.8 4.1 5.5 ns tOD2 2.8 4.1 5.5 ns Altera Corporation 77 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 53. EPF10K130E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tOD3 4.0 5.6 7.5 ns tXZ 2.8 4.1 5.5 ns tZX1 2.8 4.1 5.5 ns tZX2 2.8 4.1 5.5 ns tZX3 4.0 5.6 7.5 ns tINREG 2.5 3.0 4.1 ns tIOFD 0.4 0.5 0.6 ns tINCOMB 0.4 0.5 0.6 ns Table 54. EPF10K130E Device EAB Internal Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.5 2.0 2.6 ns tEABDATA2 0.0 0.0 0.0 ns tEABWE1 1.5 2.0 2.6 ns tEABWE2 0.3 0.4 0.5 ns tEABRE1 0.3 0.4 0.5 ns tEABRE2 0.0 0.0 0.0 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.3 0.4 0.5 ns tEABBYPASS 0.1 0.1 0.2 ns tEABSU 0.8 1.0 1.4 tEABH 0.1 0.2 0.2 ns tEABCLR 0.3 0.4 0.5 ns tAA 4.0 5.0 ns 6.6 ns tWP 2.7 3.5 4.7 ns tRP 1.0 1.3 1.7 ns tWDSU 1.0 1.3 1.7 ns tWDH 0.2 0.2 0.3 ns tWASU 1.6 2.1 2.8 ns tWAH 1.6 2.1 2.8 ns tRASU 3.0 3.9 5.2 ns tRAH 0.1 0.1 0.2 tWO 78 1.5 2.0 ns 2.6 ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 54. EPF10K130E Device EAB Internal Microparameters (Part 2 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDD 1.5 2.0 2.6 ns tEABOUT 0.2 0.3 0.3 ns tEABCH 1.5 2.0 2.5 ns tEABCL 2.7 3.5 4.7 ns Table 55. EPF10K130E Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 5.9 Max 7.5 Unit Max 9.9 ns tEABRCOMB 5.9 7.5 9.9 ns tEABRCREG 5.1 6.4 8.5 ns tEABWP 2.7 3.5 4.7 ns tEABWCOMB 5.9 7.7 10.3 ns tEABWCREG 5.4 7.0 9.4 ns tEABDD 3.4 4.5 5.9 ns tEABDATACO 0.5 0.7 0.8 ns tEABDATASU 0.8 1.0 1.4 ns tEABDATAH 0.1 0.1 0.2 ns tEABWESU 1.1 1.4 1.9 ns tEABWEH 0.0 0.0 0.0 ns tEABWDSU 1.0 1.3 1.7 ns tEABWDH 0.2 0.2 0.3 ns tEABWASU 4.1 5.1 6.8 ns tEABWAH 0.0 0.0 0.0 tEABWO Altera Corporation 3.4 4.5 ns 5.9 ns 79 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 56. EPF10K130E Device Interconnect Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tDIN2IOE 2.8 3.5 4.4 ns tDIN2LE 0.7 1.2 1.6 ns tDIN2DATA 1.6 1.9 2.2 ns tDCLK2IOE 1.6 2.1 2.7 ns tDCLK2LE 0.7 1.2 1.6 ns tSAMELAB 0.1 0.2 0.2 ns tSAMEROW 1.9 3.4 5.1 ns tSAMECOLUMN 0.9 2.6 4.4 ns tDIFFROW 2.8 6.0 9.5 ns tTWOROWS 4.7 9.4 14.6 ns tLEPERIPH 3.1 4.7 6.9 ns tLABCARRY 0.6 0.8 1.0 ns tLABCASC 0.9 1.2 1.6 ns Table 57. EPF10K130E External Timing Parameters Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 9.0 tINSU (3) 1.9 tINH (3) 0.0 tOUTCO (3) 2.0 tINSU (4) 0.9 tINH (4) 0.0 tOUTCO (4) 0.5 tPCISU 3.0 tPCIH 0.0 tPCICO 2.0 80 Notes (1), (2) Max 12.0 2.1 2.0 - ns - - ns ns - 6.9 ns ns - 0.0 2.0 ns 9.2 - 6.0 6.2 6.0 2.0 ns ns - 0.0 0.5 16.0 0.0 7.0 1.1 4.0 Max 3.0 0.0 5.0 Unit ns - ns Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 58. EPF10K130E External Bidirectional Timing Parameters Symbol Notes (1), (2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tINSUBIDIR (3) 2.2 2.4 3.2 tINHBIDIR (3) 0.0 0.0 0.0 ns tINSUBIDIR (4) 2.8 3.0 - ns tINHBIDIR (4) 0.0 tOUTCOBIDIR (3) 2.0 tXZBIDIR (3) 2.0 5.6 tZXBIDIR (3) tOUTCOBIDIR (4) 0.0 5.0 4.0 - 7.0 ns 2.0 8.1 5.6 0.5 ns 8.1 0.5 6.0 - 9.2 ns 10.8 ns 10.8 ns - ns tXZBIDIR (4) 4.6 7.1 - ns tZXBIDIR (4) 4.6 7.1 - ns Notes to tables: (1) (2) (3) (4) All timing parameters are described in Tables 24 through 30 in this data sheet. These parameters are specified by characterization. This parameter is measured without the use of the ClockLock or ClockBoost circuits. This parameter is measured with the use of the ClockLock or ClockBoost circuits. Tables 59 through 65 show EPF10K200E device internal and external timing parameters. Table 59. EPF10K200E Device LE Timing Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.7 0.8 1.2 ns tCLUT 0.4 0.5 0.6 ns tRLUT 0.6 0.7 0.9 ns tPACKED 0.3 0.5 0.7 ns tEN 0.4 0.5 0.6 ns tCICO 0.2 0.2 0.3 ns tCGEN 0.4 0.4 0.6 ns tCGENR 0.2 0.2 0.3 ns tCASC 0.7 0.8 1.2 ns tC 0.5 0.6 0.8 ns tCO 0.5 0.6 0.8 ns tCOMB 0.4 0.6 0.8 ns tSU Altera Corporation 0.4 0.6 0.7 ns 81 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 59. EPF10K200E Device LE Timing Microparameters (Part 2 of 2) Symbol tH Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max 0.9 tPRE 0.5 tCLR Max 1.1 0.5 Max 1.5 0.6 0.6 Unit ns 0.8 ns 0.8 ns tCH 2.0 2.5 3.0 ns tCL 2.0 2.5 3.0 ns Table 60. EPF10K200E Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.6 1.9 2.6 ns tIOC 0.3 0.3 0.5 ns tIOCO 1.6 1.9 2.6 ns tIOCOMB 0.5 0.6 0.8 ns tIOSU 0.8 tIOH 0.7 0.9 1.2 0.8 ns 1.1 ns tIOCLR 0.2 0.2 0.3 ns tOD1 0.6 0.7 0.9 ns tOD2 0.1 0.2 0.7 ns tOD3 2.5 3.0 3.9 ns tXZ 4.4 5.3 7.1 ns tZX1 4.4 5.3 7.1 ns tZX2 3.9 4.8 6.9 ns tZX3 6.3 7.6 10.1 ns tINREG 4.8 5.7 7.7 ns tIOFD 1.5 1.8 2.4 ns tINCOMB 1.5 1.8 2.4 ns 82 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 61. EPF10K200E Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 2.0 2.4 3.2 ns tEABDATA1 0.4 0.5 0.6 ns tEABWE1 1.4 1.7 2.3 ns tEABWE2 0.0 0.0 0.0 ns tEABRE1 0 0 0 ns tEABRE2 0.4 0.5 0.6 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.8 0.9 1.2 ns 0.1 ns tEABBYPASS 0.0 0.1 tEABSU 0.9 1.1 1.5 ns tEABH 0.4 0.5 0.6 ns tEABCLR 0.8 0.9 1.2 tAA 3.1 3.7 ns 4.9 ns tWP 3.3 4.0 5.3 ns tRP 0.9 1.1 1.5 ns tWDSU 0.9 1.1 1.5 ns tWDH 0.1 0.1 0.1 ns tWASU 1.3 1.6 2.1 ns tWAH 2.1 2.5 3.3 ns tRASU 2.2 2.6 3.5 ns tRAH 0.1 0.1 0.2 ns tWO 2.0 2.4 3.2 ns tDD 2.0 2.4 3.2 ns tEABOUT 0.0 0.1 0.1 ns tEABCH 1.5 2.0 2.5 ns tEABCL 3.3 4.0 5.3 ns Table 62. EPF10K200E Device EAB Internal Timing Macroparameters (Part 1 of 2) Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 5.1 Max 6.4 Note (1) Unit Max 8.4 ns tEABRCOMB 5.1 6.4 8.4 ns tEABRCREG 4.8 5.7 7.6 ns tEABWP 3.3 4.0 5.3 ns Altera Corporation 83 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 62. EPF10K200E Device EAB Internal Timing Macroparameters (Part 2 of 2) Symbol -1 Speed Grade -2 Speed Grade Min Min Max Max -3 Speed Grade Min Note (1) Unit Max tEABWCOMB 6.7 8.1 10.7 ns tEABWCREG 6.6 8.0 10.6 ns tEABDD 4.0 5.1 6.7 ns tEABDATACO 0.8 1.0 1.3 ns tEABDATASU 1.3 1.6 2.1 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 0.9 1.1 1.5 ns tEABWEH 0.4 0.5 0.6 ns tEABWDSU 1.5 1.8 2.4 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 3.0 3.6 4.7 ns tEABWAH 0.4 0.5 0.7 tEABWO 3.4 5.8 Table 63. EPF10K200E Device Interconnect Timing Microparameters Symbol ns 4.4 Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Unit Max tDIN2IOE 4.2 4.6 5.7 ns tDIN2LE 1.7 1.7 2.0 ns tDIN2DATA 1.9 2.1 3.0 ns tDCLK2IOE 2.5 2.9 4.0 ns tDCLK2LE 1.7 1.7 2.0 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 2.3 2.6 3.6 ns tSAMECOLUMN 2.5 2.7 4.1 ns tDIFFROW 4.8 5.3 7.7 ns tTWOROWS 7.1 7.9 11.3 ns tLEPERIPH 7.0 7.6 9.0 ns tLABCARRY 0.1 0.1 0.2 ns tLABCASC 0.9 1.0 1.4 ns 84 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 64. EPF10K200E External Timing Parameters Symbol Notes (1), (2) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 10.0 Max 12.0 Unit Max 16.0 ns tINSU 2.8 3.4 4.4 ns tINH 0.0 0.0 0.0 ns tOUTCO 2.0 tPCISU 3.0 tPCIH 0.0 tPCICO 2.0 4.5 2.0 5.3 0.0 6.0 2.0 7.8 - ns - - -2 Speed Grade -3 Speed Grade Min Min Min Max tINSUBIDIR 3.0 4.0 5.5 tINHBIDIR 0.0 0.0 0.0 tOUTCOBIDIR 2.0 4.5 2.0 5.3 ns Notes (1), (2) -1 Speed Grade Max ns ns 8.9 Table 65. EPF10K200E External Bidirectional Timing Parameters Symbol 2.0 6.2 2.0 Unit Max ns ns 7.8 ns tXZBIDIR 8.1 9.5 13.0 ns tZXBIDIR 8.1 9.5 13.0 ns Notes to tables: (1) (2) All timing parameters are described in Tables 24 through 30 in this data sheet. These parameters are specified by characterization. Tables 66 through 79 show EPF10K50S and EPF10K200S device external timing parameters. Table 66. EPF10K50S Device LE Timing Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.6 0.8 1.1 ns tCLUT 0.5 0.6 0.8 ns tRLUT 0.6 0.7 0.9 ns tPACKED 0.2 0.3 0.4 ns tEN 0.6 0.7 0.9 ns tCICO 0.1 0.1 0.1 ns tCGEN 0.4 0.5 0.6 ns Altera Corporation 85 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 66. EPF10K50S Device LE Timing Microparameters (Part 2 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tCGENR 0.1 0.1 0.1 ns tCASC 0.5 0.8 1.0 ns tC 0.5 0.6 0.8 ns tCO 0.6 0.6 0.7 ns tCOMB 0.3 0.4 0.5 ns tSU 0.5 0.6 0.7 ns tH 0.5 0.6 0.8 ns 0.4 tPRE tCLR 0.5 0.8 1.0 0.7 ns 1.2 ns tCH 2.0 2.5 3.0 ns tCL 2.0 2.5 3.0 ns Table 67. EPF10K50S Device IOE Timing Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.3 1.3 1.9 ns tIOC 0.3 0.4 0.4 ns tIOCO 1.7 2.1 2.6 ns tIOCOMB 0.5 0.6 0.8 ns tIOSU 0.8 1.0 1.3 ns tIOH 0.4 0.5 0.6 ns tIOCLR 0.2 0.2 0.4 ns tOD1 1.2 1.2 1.9 ns tOD2 0.7 0.8 1.7 ns tOD3 2.7 3.0 4.3 ns tXZ 4.7 5.7 7.5 ns tZX1 4.7 5.7 7.5 ns tZX2 4.2 5.3 7.3 ns tZX3 6.2 7.5 9.9 ns tINREG 3.5 4.2 5.6 ns tIOFD 1.1 1.3 1.8 ns tINCOMB 1.1 1.3 1.8 ns 86 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 68. EPF10K50S Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.7 2.4 3.2 ns tEABDATA2 0.4 0.6 0.8 ns tEABWE1 1.0 1.4 1.9 ns tEABWE2 0.0 0.0 0.0 ns tEABRE1 0.0 0.0 0.0 tEABRE2 0.4 0.6 0.8 tEABCLK 0.0 0.0 0.0 ns tEABCO 0.8 1.1 1.5 ns 0.0 ns tEABBYPASS 0.0 0.0 tEABSU 0.7 1.0 1.3 ns tEABH 0.4 0.6 0.8 ns tEABCLR 0.8 1.1 1.5 tAA 2.0 2.8 3.8 ns tWP 2.0 2.8 3.8 tRP 1.0 1.4 1.9 tWDSU 0.5 0.7 0.9 ns tWDH 0.1 0.1 0.2 ns tWASU 1.0 1.4 1.9 ns tWAH 1.5 2.1 2.9 ns tRASU 1.5 2.1 2.8 tRAH 0.1 0.1 ns 0.2 tWO 2.1 2.9 4.0 ns tDD 2.1 2.9 4.0 ns tEABOUT 0.0 0.0 0.0 ns tEABCH 1.5 2.0 2.5 ns tEABCL 1.5 2.0 2.5 ns Altera Corporation 87 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 69. EPF10K50S Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 3.7 Max 5.2 Unit Max 7.0 ns tEABRCCOMB 3.7 5.2 7.0 ns tEABRCREG 3.5 4.9 6.6 ns tEABWP 2.0 2.8 3.8 ns tEABWCCOMB 4.5 6.3 8.6 ns tEABWCREG 5.6 7.8 10.6 ns tEABDD 3.8 5.3 7.2 ns tEABDATACO 0.8 1.1 1.5 ns tEABDATASU 1.1 1.6 2.1 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 0.7 1.0 1.3 ns tEABWEH 0.4 0.6 0.8 ns tEABWDSU 1.2 1.7 2.2 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 1.6 2.3 3.0 ns tEABWAH 0.9 1.2 1.8 3.1 tEABWO 4.3 Table 70. EPF10K50S Device Interconnect Timing Microparameters Symbol ns 5.9 Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Unit Max tDIN2IOE 3.1 3.7 4.6 ns tDIN2LE 1.7 2.1 2.7 ns tDIN2DATA 2.7 3.1 5.1 ns tDCLK2IOE 1.6 1.9 2.6 ns tDCLK2LE 1.7 2.1 2.7 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 1.5 1.7 2.4 ns tSAMECOLUMN 1.0 1.3 2.1 ns tDIFFROW 2.5 3.0 4.5 ns tTWOROWS 4.0 4.7 6.9 ns tLEPERIPH 2.6 2.9 3.4 ns tLABCARRY 0.1 0.2 0.2 ns tLABCASC 0.8 1.0 1.3 ns 88 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 71. EPF10K50S External Timing Parameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tDRR Max 8.0 Max 9.5 Unit Max 12.5 ns tINSU (2) 2.4 2.9 3.9 ns tINH (2) 0.0 0.0 0.0 ns tOUTCO (2) 2.0 tINSU (3) 2.4 tINH (3) 0.0 tOUTCO (3) 0.5 tPCISU 2.4 tPCIH 0.0 tPCICO 2.0 4.3 2.0 5.2 7.3 0.0 3.3 0.5 ns 4.1 2.9 2.0 ns - 0.0 6.0 ns - 7.7 - ns - -2 Speed Grade -3 Speed Grade Min Min Min Max ns Note (1) -1 Speed Grade Max ns ns Table 72. EPF10K50S External Bidirectional Timing Parameters Symbol 2.0 2.9 Unit Max tINSUBIDIR (2) 2.7 3.2 4.3 ns tINHBIDIR (2) 0.0 0.0 0.0 ns tINHBIDIR (3) 0.0 0.0 - ns tINSUBIDIR (3) 3.7 4.2 - ns tOUTCOBIDIR (2) 2.0 4.5 2.0 5.2 2.0 7.3 ns tXZBIDIR (2) 6.8 7.8 10.1 ns tZXBIDIR (2) 6.8 7.8 10.1 ns tOUTCOBIDIR (3) 0.5 3.5 0.5 4.2 - - tXZBIDIR (3) 6.8 8.4 - ns tZXBIDIR (3) 6.8 8.4 - ns Notes to tables: (1) (2) (3) All timing parameters are described in Tables 24 through 30. This parameter is measured without use of the ClockLock or ClockBoost circuits. This parameter is measured with use of the ClockLock or ClockBoost circuits Altera Corporation 89 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 73. EPF10K200S Device Internal & External Timing Parameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tLUT 0.7 0.8 1.2 ns tCLUT 0.4 0.5 0.6 ns tRLUT 0.5 0.7 0.9 ns tPACKED 0.4 0.5 0.7 ns tEN 0.6 0.5 0.6 ns tCICO 0.1 0.2 0.3 ns tCGEN 0.3 0.4 0.6 ns tCGENR 0.1 0.2 0.3 ns tCASC 0.7 0.8 1.2 ns tC 0.5 0.6 0.8 ns tCO 0.5 0.6 0.8 ns tCOMB 0.3 0.6 0.8 ns tSU 0.4 0.6 0.7 ns tH 1.0 1.1 1.5 ns tPRE 0.4 0.6 0.8 ns tCLR 0.5 0.6 0.8 ns tCH 2.0 2.5 3.0 ns tCL 2.0 2.5 3.0 ns Table 74. EPF10K200S Device IOE Timing Microparameters (Part 1 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tIOD 1.8 1.9 2.6 ns tIOC 0.3 0.3 0.5 ns tIOCO 1.7 1.9 2.6 ns 0.8 ns 0.5 tIOCOMB 0.6 tIOSU 0.8 0.9 1.2 ns tIOH 0.4 0.8 1.1 ns tIOCLR 0.2 0.2 0.3 ns tOD1 1.3 0.7 0.9 ns tOD2 0.8 0.2 0.4 ns tOD3 2.9 3.0 3.9 ns tXZ 5.0 5.3 7.1 ns tZX1 5.0 5.3 7.1 ns 90 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 74. EPF10K200S Device IOE Timing Microparameters (Part 2 of 2) Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tZX2 4.5 4.8 6.6 ns tZX3 6.6 7.6 10.1 ns tINREG 3.7 5.7 7.7 ns tIOFD 1.8 3.4 4.0 ns tINCOMB 1.8 3.4 4.0 ns Table 75. EPF10K200S Device EAB Internal Microparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max Unit Max tEABDATA1 1.8 2.4 3.2 ns tEABDATA1 0.4 0.5 0.6 ns tEABWE1 1.1 1.7 2.3 ns tEABWE2 0.0 0.0 0.0 ns tEABRE1 0 0 0 ns tEABRE2 0.4 0.5 0.6 ns tEABCLK 0.0 0.0 0.0 ns tEABCO 0.8 0.9 1.2 ns tEABBYPASS 0.0 0.1 0.1 ns tEABSU 0.7 1.1 1.5 ns tEABH 0.4 0.5 0.6 ns tEABCLR 0.8 0.9 1.2 tAA 2.1 3.7 ns 4.9 ns tWP 2.1 4.0 5.3 ns tRP 1.1 1.1 1.5 ns tWDSU 0.5 1.1 1.5 ns tWDH 0.1 0.1 0.1 ns tWASU 1.1 1.6 2.1 ns tWAH 1.6 2.5 3.3 ns tRASU 1.6 2.6 3.5 ns tRAH 0.1 0.1 0.2 ns tWO 2.0 2.4 3.2 ns tDD 2.0 2.4 3.2 ns tEABOUT 0.0 0.1 0.1 ns tEABCH 1.5 2.0 2.5 ns tEABCL 2.1 2.8 3.8 ns Altera Corporation 91 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 76. EPF10K200S Device EAB Internal Timing Macroparameters Symbol Note (1) -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tEABAA Max 3.9 Max 6.4 Unit Max 8.4 ns tEABRCOMB 3.9 6.4 8.4 ns tEABRCREG 3.6 5.7 7.6 ns tEABWP 2.1 4.0 5.3 ns tEABWCOMB 4.8 8.1 10.7 ns tEABWCREG 5.4 8.0 10.6 ns tEABDD 3.8 5.1 6.7 ns tEABDATACO 0.8 1.0 1.3 ns tEABDATASU 1.1 1.6 2.1 ns tEABDATAH 0.0 0.0 0.0 ns tEABWESU 0.7 1.1 1.5 ns tEABWEH 0.4 0.5 0.6 ns tEABWDSU 1.2 1.8 2.4 ns tEABWDH 0.0 0.0 0.0 ns tEABWASU 1.9 3.6 4.7 ns tEABWAH 0.8 0.5 0.7 3.1 tEABWO 4.4 ns 5.8 Table 77. EPF10K200S Device Interconnect Timing Microparameters (Part 1 of 2) Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Note (1) Unit Max tDIN2IOE 4.4 4.8 5.5 ns tDIN2LE 0.6 0.6 0.9 ns tDIN2DATA 1.8 2.1 2.8 ns tDCLK2IOE 1.7 2.0 2.8 ns tDCLK2LE 0.6 0.6 0.9 ns tSAMELAB 0.1 0.1 0.2 ns tSAMEROW 3.0 4.6 5.7 ns tSAMECOLUMN 3.5 4.9 6.4 ns tDIFFROW 6.5 9.5 12.1 ns tTWOROWS 9.5 14.1 17.8 ns tLEPERIPH 5.5 6.2 7.2 ns tLABCARRY 0.3 0.1 0.2 ns 92 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Table 77. EPF10K200S Device Interconnect Timing Microparameters (Part 2 of 2) Symbol -1 Speed Grade -2 Speed Grade -3 Speed Grade Min Min Min tLABCASC Max 0.5 Max 1.0 Table 78. EPF10K200S External Timing Parameters Symbol Note (1) Max 1.4 -2 Speed Grade -3 Speed Grade Min Min Min tDRR 9.0 ns Note (1) -1 Speed Grade Max Unit Max 12.0 Unit Max 16.0 ns tINSU (2) 3.1 3.7 4.7 ns tINH (2) 0.0 0.0 0.0 ns tOUTCO (2) 2.0 3.7 2.0 4.4 2.0 6.3 ns tINSU(3) 2.1 2.7 - tINH (3) 0.0 0.0 - tOUTCO(3) 0.5 tPCISU 3.0 4.2 - ns tPCIH 0.0 0.0 - ns tPCICO 2.0 2.7 6.0 0.5 2.0 3.4 8.9 Table 79. EPF10K200S External Bidirectional Timing Parameters Symbol tINSUBIDIR (2) - - ns ns - - -2 Speed Grade -3 Speed Grade Min Min Min Max Max ns Note (1) -1 Speed Grade 2.3 ns 3.4 4.4 Unit Max ns tINHBIDIR (2) 0.0 0.0 0.0 ns tINSUBIDIR (3) 3.3 4.4 - ns tINHBIDIR (3) 0.0 tOUTCOBIDIR (2) 2.0 0.0 3.7 2.0 - 4.4 2.0 ns 6.3 ns tXZBIDIR (2) 6.9 7.6 9.2 ns tZXBIDIR (2) 5.9 6.6 - ns tOUTCOBIDIR (3) - ns tXZBIDIR (3) 0.5 2.7 6.9 0.5 3.4 7.6 - 9.2 ns tZXBIDIR (3) 5.9 6.6 - ns Notes to tables: (1) (2) (3) All timing parameters are described in Tables 24 through 30 in this data sheet. This parameter is measured without the use of the ClockLock or ClockBoost circuits. This parameter is measured with the use of the ClockLock or ClockBoost circuits. Altera Corporation 93 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Power Consumption The supply power (P) for FLEX 10KE devices can be calculated with the following equation: P = PINT + PIO = (I CCSTANDBY + ICCACTIVE) x VCC + PIO The ICCACTIVE value depends on the switching frequency and the application logic. This value is calculated based on the amount of current that each LE typically consumes. The PIO value, which depends on the device output load characteristics and switching frequency, can be calculated using the guidelines given in Application Note 74 (Evaluating Power for Altera Devices). Compared to the rest of the device, the embedded array consumes a negligible amount of power. Therefore, the embedded array can be ignored when calculating supply current. The ICCACTIVE value can be calculated with the following equation: A ICCACTIVE = K x fMAX x N x togLC x --------------------------MHz x LE Where: fMAX N togLC = = = K = Maximum operating frequency in MHz Total number of LEs used in the device Average percent of LEs toggling at each clock (typically 12.5%) Constant Table 80 provides the constant (K) values for FLEX 10KE devices. Table 80. FLEX 10KE K Constant Values Device K Value EPF10K30E 4.5 EPF10K50E 4.8 EPF10K50S 4.5 EPF10K100E 4.5 EPF10K130E 4.6 EPF10K200E 4.8 EPF10K200S 4.6 This calculation provides an ICC estimate based on typical conditions with no output load. The actual ICC should be verified during operation because this measurement is sensitive to the actual pattern in the device and the environmental operating conditions. 94 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet To better reflect actual designs, the power model (and the constant K in the power calculation equations) for continuous interconnect FLEX devices assumes that LEs drive FastTrack Interconnect channels. In contrast, the power model of segmented FPGAs assumes that all LEs drive only one short interconnect segment. This assumption may lead to inaccurate results when compared to measured power consumption for actual designs in segmented FPGAs. Figure 31 shows the relationship between the current and operating frequency of FLEX 10KE devices. Figure 31. FLEX 10KE ICCACTIVE vs. Operating Frequency (Part 1 of 2) EPF10K50E EPF10K30E 200 100 80 ICC Supply 150 ICC Supply 60 Current (mA) Current (mA) 100 40 50 20 0 50 0 100 50 100 Frequency (MHz) Frequency (MHz) EPF10K100E EPF10K50S 300 200 150 ICC Supply ICC Supply Current (mA) 200 Current (mA) 100 100 50 0 50 Frequency (MHz) Altera Corporation 100 0 50 100 Frequency (MHz) 95 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Figure 31. FLEX 10KE ICCACTIVE vs. Operating Frequency (Part 2 of 2) EPF10K130E EPF10K200E 400 600 300 ICC Supply Current (mA) ICC Supply 200 400 Current (mA) 200 100 0 50 0 100 50 100 Frequency (MHz) Frequency (MHz) EPF10K200S 600 ICC Supply 400 Current (mA) 200 0 50 100 Frequency (MHz) Configuration & Operation The FLEX 10KE architecture supports several configuration schemes. This section summarizes the device operating modes and available device configuration schemes. Operating Modes The FLEX 10KE architecture uses SRAM configuration elements that require configuration data to be loaded every time the circuit powers up. The process of physically loading the SRAM data into the device is called configuration. Before configuration, as VCC rises, the device initiates a Power-On Reset (POR). This POR event clears the device and prepares it for configuration. The FLEX 10KE POR time does not exceed 50 s. When configuring with a configuration device, refer to the respective configuration device data sheet for POR timing information. 96 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet During initialization, which occurs immediately after configuration, the device resets registers, enables I/O pins, and begins to operate as a logic device. The I/O pins are tri-stated during power-up, and before and during configuration. Together, the configuration and initialization processes are called command mode; normal device operation is called user mode. SRAM configuration elements allow FLEX 10KE devices to be reconfigured in-circuit by loading new configuration data into the device. Real-time reconfiguration is performed by forcing the device into command mode with a device pin, loading different configuration data, reinitializing the device, and resuming user-mode operation. The entire reconfiguration process requires less than 85 ms and can be used to reconfigure an entire system dynamically. In-field upgrades can be performed by distributing new configuration files. Before and during configuration, all I/O pins (except dedicated inputs, clock, or configuration pins) are pulled high by a weak pull-up resistor. Programming Files Despite being function- and pin-compatible, FLEX 10KE devices are not programming- or configuration file-compatible with FLEX 10K or FLEX 10KA devices. A design therefore must be recompiled before it is transferred from a FLEX 10K or FLEX 10KA device to an equivalent FLEX 10KE device. This recompilation should be performed both to create a new programming or configuration file and to check design timing in FLEX 10KE devices, which has different timing characteristics than FLEX 10K or FLEX 10KA devices. FLEX 10KE devices are generally pin-compatible with equivalent FLEX 10KA devices. In some cases, FLEX 10KE devices have fewer I/O pins than the equivalent FLEX 10KA devices. Table 81 shows which FLEX 10KE devices have fewer I/O pins than equivalent FLEX 10KA devices. However, power, ground, JTAG, and configuration pins are the same on FLEX 10KA and FLEX 10KE devices, enabling migration from a FLEX 10KA design to a FLEX 10KE design. Altera Corporation 97 FLEX 10KE Embedded Programmable Logic Devices Data Sheet Additionally, the Altera software offers several features that help plan for future device migration by preventing the use of conflicting I/O pins. Table 81. I/O Counts for FLEX 10KA & FLEX 10KE Devices FLEX 10KA FLEX 10KE Device I/O Count Device I/O Count EPF10K30AF256 191 EPF10K30EF256 176 EPF10K30AF484 246 EPF10K30EF484 220 EPF10K50VB356 274 EPF10K50SB356 220 EPF10K50VF484 291 EPF10K50EF484 254 EPF10K50VF484 291 EPF10K50SF484 254 EPF10K100AF484 369 EPF10K100EF484 338 Configuration Schemes The configuration data for a FLEX 10KE device can be loaded with one of five configuration schemes (see Table 82), chosen on the basis of the target application. An EPC1, EPC2, or EPC16 configuration device, intelligent controller, or the JTAG port can be used to control the configuration of a FLEX 10KE device, allowing automatic configuration on system power-up. Multiple FLEX 10KE devices can be configured in any of the five configuration schemes by connecting the configuration enable (nCE) and configuration enable output (nCEO) pins on each device. Additional FLEX 10K, FLEX 10KA, FLEX 10KE, and FLEX 6000 devices can be configured in the same serial chain. Table 82. Data Sources for FLEX 10KE Configuration Configuration Scheme Data Source Configuration device EPC1, EPC2, or EPC16 configuration device Passive serial (PS) BitBlaster, ByteBlasterMV, or MasterBlaster download cables, or serial data source Passive parallel asynchronous (PPA) Parallel data source Passive parallel synchronous (PPS) Parallel data source JTAG BitBlaster or ByteBlasterMV download cables, or microprocessor with a Jam STAPL file or JBC file 98 Altera Corporation FLEX 10KE Embedded Programmable Logic Devices Data Sheet Device Pin-Outs See the Altera web site (http://www.altera.com) or the Altera Digital Library for pin-out information. Revision History The information contained in the FLEX 10KE Embedded Programmable Logic Data Sheet version 2.5 supersedes information published in previous versions. Version 2.5 The following changes were made to the FLEX 10KE Embedded Programmable Logic Data Sheet version 2.5: Note (1) added to Figure 23. Text added to "I/O Element" section on page 34. Updated Table 22. Version 2.4 The following changes were made to the FLEX 10KE Embedded Programmable Logic Data Sheet version 2.4: updated text on page 34 and page 63. Altera Corporation 99 FLEX 10KE Embedded Programmable Logic Devices Data Sheet 101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Applications Hotline: (800) 800-EPLD Literature Services: lit_req@altera.com 100 Copyright (c) 2003 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. Altera Corporation Printed on Recycled Paper. Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K200S* 27 part numbers found and 0 obsolete part numbers found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Part Number Buying Altera Devices Device Pin & Package Temperature Speeds Options EPF10K200SBC356-1 EPF10K200S 356 pin BGA EPF10K200SBC356-1X Pinout EPF10K200SBC356-2 EPF10K200SBC356-2X EPF10K200SBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SBC600-1 EPF10K200S 600 pin BGA EPF10K200SBC600-1X Pinout EPF10K200SBC600-2 EPF10K200SBC600-2X EPF10K200SBC600-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SBI356-2 Industrial -2 ( -40 to 100C) EPF10K200S 356 pin BGA Pinout None EPF10K200SFC484-1 EPF10K200S 484 pin FBGA EPF10K200SFC484-1X Pinout EPF10K200SFC484-2 EPF10K200SFC484-2X EPF10K200SFC484-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SFC672-1 EPF10K200S 672 pin FBGA EPF10K200SFC672-1X Pinout EPF10K200SFC672-2 EPF10K200SFC672-2X EPF10K200SFC672-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K200SFI672-2 Industrial -2 ( -40 to 100C) EPF10K200S 672 pin FBGA Pinout EPF10K200SRC240-1 EPF10K200S 240 pin RQFP EPF10K200SRC240-1X Pinout EPF10K200SRC240-2 EPF10K200SRC240-2X EPF10K200SRC240-3 EPF10K200S* Advanced Commercial ( 0 to 85C) None -1, -2, -3 X: Has PLLs Search Help Please Give Us Feedback Sign Up for E-mail Updates http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K200S*&scope=0 (1 of 2) [9/3/2004 10:18:57 AM] Altera Part Number Search Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K200S*&scope=0 (2 of 2) [9/3/2004 10:18:57 AM] Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K50S* 22 part numbers found and 1 obsolete part number found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Buying Altera Devices Part Number Device Pin & Package Temperature Speeds Options EPF10K50SBC356-1 EPF10K50S 356 pin BGA EPF10K50SBC356-1X Pinout EPF10K50SBC356-2 EPF10K50SBC356-2X EPF10K50SBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SFC256-1 EPF10K50SFC256-1X EPF10K50SFC256-2 EPF10K50SFC256-2X EPF10K50SFC256-3 EPF10K50S 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SFC484-1 EPF10K50SFC484-1X EPF10K50SFC484-2 EPF10K50SFC484-2X EPF10K50SFC484-3 EPF10K50S 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SQC208-1X EPF10K50S 208 pin PQFP Pinout Commercial ( 0 to 85C) -1 EPF10K50S 240 pin PQFP EPF10K50SQC240-1 EPF10K50SQC240-1X Pinout EPF10K50SQC240-2 EPF10K50SQC240-2X EPF10K50SQC240-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K50SQI208-2 Industrial -2 ( -40 to 100C) EPF10K50S 208 pin PQFP Pinout X: Has PLLs None Your search for EPF10K50S* found 1 obsolete part number. Obsolete Part Numbers Part Number Format Part Number Buying Altera Devices Last Order Date Last Ship Date Replacement EPF10K50SFI484-2 12/15/04 6/15/05 EPF10K50S* Advanced Notes EPF10K50SFC484-1 PDN 0314 Search Help http://www.altera.com/cgi-bin/devsearch.pl?searc...ocsetConstraints=&col=corp&qt=EPF10K50S*&scope=0 (1 of 2) [9/3/2004 10:18:41 AM] Altera Part Number Search Please Give Us Feedback Sign Up for E-mail Updates Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searc...ocsetConstraints=&col=corp&qt=EPF10K50S*&scope=0 (2 of 2) [9/3/2004 10:18:41 AM] Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K100E* 28 part numbers found and 0 obsolete part numbers found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Part Number Buying Altera Devices Device Pin & Package Temperature Speeds Options EPF10K100EBC356-1 EPF10K100E 356 pin BGA EPF10K100EBC356-1X Pinout EPF10K100EBC356-2 EPF10K100EBC356-2X EPF10K100EBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EFC256-1 EPF10K100EFC256-1X EPF10K100EFC256-2 EPF10K100EFC256-2X EPF10K100EFC256-3 EPF10K100E 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EFC484-1 EPF10K100EFC484-1X EPF10K100EFC484-2 EPF10K100EFC484-2X EPF10K100EFC484-3 EPF10K100E 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EFI256-2 EPF10K100E 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K100EFI484-2 EPF10K100E 484 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K100E 208 pin PQFP EPF10K100EQC208-1 EPF10K100EQC208-1X Pinout EPF10K100EQC208-2 EPF10K100EQC208-2X EPF10K100EQC208-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EQC240-1 EPF10K100E 240 pin PQFP EPF10K100EQC240-1X Pinout EPF10K100EQC240-2 EPF10K100EQC240-2X EPF10K100EQC240-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K100EQI208-2 Industrial -2 ( -40 to 100C) EPF10K100E 208 pin PQFP Pinout EPF10K100E* Advanced None Search Help Please Give Us Feedback Sign Up for E-mail Updates http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K100E*&scope=0 (1 of 2) [9/3/2004 10:18:44 AM] Altera Part Number Search Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K100E*&scope=0 (2 of 2) [9/3/2004 10:18:44 AM] Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K130E* 28 part numbers found and 0 obsolete part numbers found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Part Number Buying Altera Devices Device Pin & Package Temperature Speeds Options EPF10K130EBC356-1 EPF10K130E 356 pin BGA EPF10K130EBC356-1X Pinout EPF10K130EBC356-2 EPF10K130EBC356-2X EPF10K130EBC356-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EBC600-1 EPF10K130E 600 pin BGA EPF10K130EBC600-1X Pinout EPF10K130EBC600-2 EPF10K130EBC600-2X EPF10K130EBC600-3 Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EBI356-2 EPF10K130E 356 pin BGA Pinout Industrial -2 ( -40 to 100C) EPF10K130EFC484-1 EPF10K130EFC484-1X EPF10K130EFC484-2 EPF10K130EFC484-2X EPF10K130EFC484-3 EPF10K130E 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EFC672-1 EPF10K130EFC672-1X EPF10K130EFC672-2 EPF10K130EFC672-2X EPF10K130EFC672-3 EPF10K130E 672 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 X: Has PLLs EPF10K130EFI484-2 EPF10K130E 484 pin FBGA Pinout Industrial -2 ( -40 to 100C) EPF10K130EQC240-1 EPF10K130E 240 pin PQFP EPF10K130EQC240-1X Pinout EPF10K130EQC240-2 EPF10K130EQC240-2X EPF10K130EQC240-3 Commercial ( 0 to 85C) EPF10K130EQI240-2 Industrial -2 ( -40 to 100C) EPF10K130E 240 pin PQFP Pinout EPF10K130E* Advanced None None -1, -2, -3 X: Has PLLs None Search Help Please Give Us Feedback Sign Up for E-mail Updates http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K130E*&scope=0 (1 of 2) [9/3/2004 10:18:48 AM] Altera Part Number Search Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searc...csetConstraints=&col=corp&qt=EPF10K130E*&scope=0 (2 of 2) [9/3/2004 10:18:48 AM] Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K200E* 7 part numbers found and 3 obsolete part numbers found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Part Number Buying Altera Devices Device Pin & Package Temperature Speeds EPF10K200EBC600-1 EPF10K200E 600 pin BGA EPF10K200EBC600-2 Pinout EPF10K200EBC600-3 Commercial ( 0 to 85C) EPF10K200EBI600-2 Industrial -2 ( -40 to 100C) EPF10K200E 600 pin BGA Pinout EPF10K200EFC672-1 EPF10K200E 672 pin FBGA EPF10K200EFC672-2 Pinout EPF10K200EFC672-3 Commercial ( 0 to 85C) Options -1, -2, -3 None None -1, -2, -3 None Your search for EPF10K200E* found 3 obsolete part numbers. Obsolete Part Numbers Part Number Format Part Number Buying Altera Devices Last Order Date Last Ship Date Replacement Notes EPF10K200EGC599-1 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200EGC599-2 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200EGC599-3 2/28/03 8/31/03 Contact Altera PDN 0107 EPF10K200E* Advanced Search Help Please Give Us Feedback Sign Up for E-mail Updates Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searchText=&docsetConstraints=&col=corp&qt=EPF10K200E*&scope=0 [9/3/2004 10:18:52 AM] Altera Part Number Search Literature Licensing Buy On-Line Download Entire Site Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Results For: EPF10K50E* 18 part numbers found and 0 obsolete part numbers found FLEX 10KE Device Family (2.5V) FLEX 10KE Datasheet FLEX 10K Literature Part Number Format Buying Altera Devices Part Number Device Pin & Package Temperature Speeds Options EPF10K50EFC256-1 EPF10K50EFC256-2 EPF10K50EFC256-3 EPF10K50E 256 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EFC484-1 EPF10K50EFC484-2 EPF10K50EFC484-3 EPF10K50E 484 pin FBGA Pinout Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EFI256-2 EPF10K50E 256 pin FBGA Pinout Industrial -2 ( -40 to 100C) None EPF10K50EQC208-1 EPF10K50E 208 pin PQFP EPF10K50EQC208-2 Pinout EPF10K50EQC208-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EQC240-1 EPF10K50E 240 pin PQFP EPF10K50EQC240-2 Pinout EPF10K50EQC240-3 Commercial ( 0 to 85C) -1, -2, -3 None EPF10K50EQI240-2 EPF10K50E 240 pin PQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50ETC144-1 EPF10K50ETC144-2 EPF10K50ETC144-3 EPF10K50E 144 pin TQFP Pinout Commercial ( 0 to 85C) EPF10K50ETI144-2 EPF10K50E 144 pin TQFP Pinout Industrial -2 ( -40 to 100C) EPF10K50E* Advanced None -1, -2, -3 None None Search Help Please Give Us Feedback Sign Up for E-mail Updates Home | Products | Support | System Solutions | Technology Center | Education & Events | Corporate | Buy On-Line Contact Us | New User | Site Map | Privacy | Legal Notice Copyright (c) 1995-2004 Altera Corporation, 101 Innovation Drive, San Jose, California 95134, USA http://www.altera.com/cgi-bin/devsearch.pl?searchText=&docsetConstraints=&col=corp&qt=EPF10K50E*&scope=0 [9/3/2004 10:18:36 AM]