1www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
Truth Table
E S YA YB YC YD Function
H X Hi-Z Hi-Z Hi-Z Hi-Z Disable
L L IA0 IB0 IC0 ID0S = 0
L H IA1 IB1 IC1 ID1S = 1
Pin Description
Pin Name Description
IAn-IDn Data Inputs
S Select Inputs
E Enable
YA-YD Data Outputs
GND Ground
VCC Power
Block Diagram
Pin Configuration
Note:
H = High Voltage Level,
L = Low Voltage Level, S
witches are shown with logic "0" input (Select and Enable)
Features
¼Single 3.3V/5V supply operation
¼Rail-To-Rail Operation
¼Very Low Distortion: 2%
¼Replaces mechanical relays
¼High-performance, low-cost solution for switching between
dierent LAN signals
¼Low crosstalk: –70dB @ 30 Mbps
¼Low insertion loss and On-Resistance: 6-ohms typical
¼O isolation: –55dB @ 30 Mbps
¼Wide bandwidth data rates >135 Mbps
¼Low Quiescent Supply Current (100nA typical)
¼Packaging (Pb-free & Green available):
– 16-pin 150-mil wide plastic QSOP (Q)
– 16-pin 150-mil wide plastic SOIC (W)
– 16-pin 173-mil wide plastic TSSOP (L)
Description
Diodes' PI5L200 is a Rail-to-Rail Quad 2:1 multiplexer/demulti-
plexer LanSwitch with 3-state outputs. e On-Resistance typi-
cally varies from 5 ohms to 7 ohms with data inputs of 0V to 5V.
Generally, this part can be used to replace mechanical relays in
low voltage (3.3V/5V systems) LAN applications.
With a wide bandwidth of 135 MHz, the PI5L200 can switch Fast
Ethernet and ATM25 signals. Into 100-ohm UTP cables, the
switch distortion is typically less than two percent. Crosstalk @30
MHz is –70dB. e PI5L200 operates from a single 3.3V/5V sup-
ply and interface to TTL logic.
IA0
IA1
IB0
IB1
IC0
IC1
ID0
ID1
YA
YB
YC
YD
Decoder/Driver
S
E
1 16
2 15
3 14
4 13
5 12
6 11
7 10
8 9
S
IA0
IA1
YA
IB0
IB1
YB
GND
VCC
E
ID0
ID1
YD
IC0
IC1
YC
Precision Wide Bandwidth LanSwitch Quad 2:1 Mux/DeMux
A product Line of
Diodes Incorporated
PI5L200
Applications
¼10/100 Base-TX/T4
¼100VG-AnyLAN
¼Token Ring 4/16 Mbps
¼ATM25
¼NIC Adapter and Hubs
¼SONET OCI 51.8Mbps
¼T1/E1
2
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
DC Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 5V ±10%, GND = 0V)
Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units
V
ANALOG Analog Signal Range 0 VCC V
RON ON-Resistance ION = 10mA to 30mA 6 12
∆RON Match Between Channels 0.4 2
RFLAT(ON) RON Flatness ION = 1mA, VNO, VNC = 0V to 5V 3 5
INO(OFF), INO(ON) On/Off Leakage Current VNO, VNC = 4.5V −100 100 nA
ICC Quiescent Supply Current VCC = 5.5V, VIN = 0V or VCC 1 µA
IOOutput Current VNO, VNC or VCOM = 0V to 5V 100 mA
VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V
VIL Input LOW Voltage Guaranteed Logic LOW Level −0.5 0.8
IIH Input HIGH Current VCC = Max., VIN = VCC ±1 µA
IIL Input LOW Current VCC = Max., VIN = GND ±1
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Note:
Stresses greater than those listed under MAXIMUM RAT-
INGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
these or any other conditions above those indicated in the
operational sections of this specication is not implied. Ex-
posure to absolute maximum rating conditions for extended
periods may affect reliability.
Storage Temperature .......................................................... –65°C to +150°C
Ambient Temperature with Power Applied ......................... –40°C to +85°C
Supply Voltage to Ground Potential ..................................... –0.5V to +7.0V
DC Input Voltage ........................................................... –0.5V to VCC+0.5V
DC Output Current ............................................................................ 120 mA
Power Dissipation ................................................................................. 0.5W
Note:
1. For Max. or Min. conditions, use appropriate value specied under Electrical Characteristics for applicable device type.
2. Guaranteed by design.
Single 5.0V Supply
Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 5V ±10%, GND = 0V)
Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units
tON Turn-on Time VON or VNC = 3.0V, see Fig. 2 10 20 ns
tOFF Turn-off Time VON or VNC = 3.0V, see Fig. 2 5 10
XTALK Crosstalk RL = 100 ohms, f = 30 MHz, see Fig. 4 −70 dB
C(OFF) NC or NO Capacitance f = 1 kHz 13 pF
OIRR Off Isolation RL = 100 ohms, f = 30 MHz, see Fig. 5 −55 dB
BW Bandwidth -3dB RL = 100 ohms, see Fig. 3 137 MHz
D Distortion DRON/RL RL = 100 ohms 2%
3
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
DC Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V)
Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units
V
ANALOG Analog Signal Range 0 VCC V
RON ON-Resistance ION = 10mA to 30mA 15 22
∆RON Match Between Channels 1 3
RFLAT(ON) RON Flatness ION = 1mA, VNO, VNC = 0V to 5V 7 12
INO(OFF), INO(ON) On/Off Leakage Current VNO, VNC = 3.0V −100 100 nA
ICOM(ON) On Leakage Current VNO, VNC = 3.0V −100 100 µA
IOOutput Current VNO, VNC or VCOM = 0V 80 mA
VIH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V
VIL Input LOW Voltage Guaranteed Logic LOW Level −0.5 0.8
IIH Input HIGH Current VCC = Max., VIN = VCC ±1 µA
IIL Input LOW Current VCC = Max., VIN = GND ±1
Note:
1. For Max. or Min. conditions, use appropriate value specied under Electrical Characteristics for applicable device type.
2. Guaranteed by design.
Single 3.3V Supply
Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V)
Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units
tON Turn-on Time VON or VNC = 1.5V, see Fig. 2 28 40 ns
tOFF Turn-off Time VON or VNC = 1.5V, see Fig. 2 4 20
XTALK Crosstalk RL = 50 ohms, f = 1 MHz, see Fig. 4 −75 dB
C(OFF) NC or NO Capacitance f = 1 kHz 15 pF
CCOM(OFF) COM Off Capacitance f = 1 kHz 30
OIRR Off Isolation RL = 50 ohms, f = 1 MHz, see Fig. 5 −75 dB
BW Bandwidth -3dB RL = 50 ohms, see Fig. 3 110 MHz
D Distortion RL = 100 ohms 4%
Dynamic Electrical Characteristics (Over the Operating Range, TA = -40°C to +85°C, VCC = 3.3V ±10%, GND = 0V)
Parameters Description Test Conditions(1) Min. Typ.(2) Max. Units
ICC Quiescent Positive Power
Supply Current
VCC = 3.6V, VIN = 0V or VCC
All Channesl ON or OFF 1 µA
4
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
Figure 2. Switching Time
Test Circuits
3V
E
In Y
GND
100W
Vcc
Vcc
35pF
V
OUT
S
DIGITAL
INPUT
ANALOG
OUTPUT
tON tOFF
50%
90%
50%
90%
TX
TRANSMIT
RX
RECEIVE
Figure 1a. Full Duplex Transceiver
Figure 1b. Loop Back
TX1
RX1
Figure 1c. Line Termination
100Ω
120Ω
Figure 1d. Line Clamp
5
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
Figure 3. Bandwidth
Figure 4. Crosstalk
HP4195
NETWORK
ANALYZER
ACTIVE PROBE
50Ω
100Ω 100Ω
V
OUT
S E
1
+5V
HP4195
NETWORK
ANALYZER
ACTIVE PROBE
50Ω
100Ω 100Ω
V
OUT
S
E
100Ω
I
A0
I
C0
Y
A
Y
A
Figure 5. Off Isolation
HP4195
NETWORK
ANALYZER
ACTIVE PROBE
50Ω
50Ω 100Ω
V
OUT
S
E
I
0
I
1
Y
6
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
0
5
10
15
20
0 2 31 4 5
3.3V
5V
R
H
= 100Ω
T
A
= 25°C
)V( egatloV tupnI
On-Resistance R
ON
(Ω)
-4
-3
-2
-1
0
1K 1M 10M 100M 1G
3.3V
5V
R
IN
= 1dBm
R
L
= 100Ω
T
A
= 25°C
Insertion Loss BW (dB)
)zH( ycneuqerF
0
-10
-20
-30
-40
-50
-60
-70
-80
1M 10M 100M 1G
3.3V, 5V
P
IN
= 1dBm
T
A
= 25°C
R
L
= 100Ω
Frequency (Hz)
Crosstalk XTALK (dB)
Figure 6. On-Resistance vs. Input Voltage Figure 7. Insertion Loss vs. Frequency
Figure 8. Off Isolation vs. Frequency Figure 9. Crosstalk vs. Frequency
7
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
PI5L
200QE
ZYWXX
Z: Die Rev Code
Y: Year
W: Workweek
1st X: Assembly Code
2nd X: Fab Code
Part Marking
Q Package W Package L Package
PI5L
200WE
BZYYWWXX
B: Port Code
Z: Die Rev
YY: Year
WW: Workweek
1st X: Assembly Code
2nd X: Fab Code
PI5L
200LE
ZYWXX
Z: Die Rev
Y: Year
W: Workweek
1st X: Assembly Code
2nd X: Fab Code
8
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
16-0056
Packaging Mechanical: 16-QSOP (Q)
9
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
Packaging Mechanical: 16-SOIC (W)
16-0145
10
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
Ordering Information
Ordering Code Packaging Code Package Description
PI5L200QEX Q 16-pin, 150mil Wide (QSOP)
PI5L200WEX W 16-pin, 150mil Wide (SOIC)
PI5L200LEX L 16-pin, 173mil Wide (TSSOP)
Packaging Mechanical: 16-TSSOP (L)
16-0061
Notes:
1. EU Directive 2002/95/EC (RoHS), 2011/65/EU (RoHS 2) & 2015/863/EU (RoHS 3) compliant. All applicable RoHS exemptions applied.
2. See http://www.diodes.com/quality/lead-free/ for more information about Diodes Incorporated’s denitions of Halogen- and Antimony-free, “Green” and Lead-free.
Thermal characteristics can be found on the company web site at www.diodes.com/design/support/packaging/
3. E = Pb-free and Green
4. X sufx = Tape/Reel
For latest package info.
please check: http://www.diodes.com/design/support/packaging/pericom-packaging/packaging-mechanicals-and-thermal-characteristics/
11
A product Line of
Diodes Incorporated
PI5L200
www.diodes.com January 2018
Diodes Incorporated
PI5L200
Document Number DS40562 Rev 1-2
IMPORTANT NOTICE
DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE
LAWS OF ANY JURISDICTION).
Diodes Incorporated and its subsidiaries reserve the right to make modications, enhancements, improvements, corrections or other changes without further notice
to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any
product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of
this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies
whose products are represented on Diodes Incorporated website, harmless against all damages.
Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incor-
porated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized application.
Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may
also be covered by one or more United States, international or foreign trademarks.
This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the nal and determina-
tive format released by Diodes Incorporated.
LIFE SUPPORT
Diodes Incorporated products are specically not authorized for use as critical components in life support devices or systems without the express written approval of
the Chief Executive Ofcer of Diodes Incorporated. As used herein:
A. Life support devices or systems are devices or systems which:
1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in signicant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.
Customers represent that they have all necessary expertise in the safety and regulatory ramications of their life support devices or systems, and acknowledge and
agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products
in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incor-
porated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated
products in such safety-critical, life support devices or systems.
Copyright © 2016, Diodes Incorporated
www.diodes.com