LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 LM2717-ADJ Dual Step-Down DC/DC Converter Check for Samples: LM2717-ADJ FEATURES DESCRIPTION * The LM2717-ADJ is composed of two PWM DC/DC buck (step-down) converters. Both converters are used to generate an adjustable output voltage as low as 1.267V. Both also feature low RDSON (0.16) internal switches for maximum efficiency. Operating frequency can be adjusted anywhere between 300kHz and 600kHz allowing the use of small external components. External soft-start pins for each converter enables the user to tailor the soft-start times to a specific application. Each converter may also be shut down independently with its own shutdown pin. The LM2717-ADJ is available in a low profile 24-lead TSSOP package ensuring a low profile overall solution. 1 2 * * * * * * Adjustable Buck Converter with a 2.2A, 0.16, Internal Switch (Buck 1) Adjustable Buck Converter with a 3.2A, 0.16, Internal Switch (Buck 2) Operating Input Voltage Range of 4V to 20V Input Undervoltage Protection 300kHz to 600kHz Pin Adjustable Operating Frequency Over Temperature Protection Small 24-Lead TSSOP Package APPLICATIONS * * * * * TFT-LCD Displays Handheld Devices Portable Applications Laptop Computers Automotive Applications 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Typical Application Circuit CBOOT1 L1 RFB1 CSS1 CB1 SW1 SS1 SHDN1 RFB2 Buck Converter 1 FB1 CC1 RC1 VOUT1 COUT1 D1 VIN VIN CIN VC1 RF L2 FSLCT SW2 CSS2 VOUT2 D2 SS2 CB2 CBG VBG Buck Converter 2 COUT2 RFB3 CBOOT2 FB2 SHDN2 CC2 RC2 AGND VC2 RFB4 PGND LM2717 - ADJ Connection Diagram Figure 1. 24-Lead TSSOP Top View 2 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 PIN DESCRIPTIONS Pin Name Function 1 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 2 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 3 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 4 FB1 Buck 1 output voltage feedback input. 5 VC1 Buck 1 compensation network connection. Connected to the output of the voltage error amplifier. 6 VBG Bandgap connection. 7 VC2 Buck 2 compensation network connection. Connected to the output of the voltage error amplifier. 8 FB2 Buck 2 output voltage feedback input. 9 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 10 AGND Analog ground. PGND and AGND pins must be connected together directly at the part. 11 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 12 PGND Power ground. PGND and AGND pins must be connected together directly at the part. 13 SW2 14 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 15 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 16 CB2 Buck 2 converter bootstrap capacitor connection. 17 SHDN2 18 SS2 19 FSLCT Buck 2 power switch input. Switch connected between VIN pins and SW2 pin. Shutdown pin for Buck 2 converter. Active low. Buck 2 soft start pin. Switching frequency select input. Use a resistor to set the frequency anywhere between 300kHz and 600kHz. 20 SS1 21 SHDN1 Buck 1 soft start pin. 22 CB1 Buck 1 converter bootstrap capacitor connection. 23 VIN Analog power input. All VIN pins are internally connected and should be connected together directly at the part. 24 SW1 Shutdown pin for Buck 1 converter. Active low. Buck 1 power switch input. Switch connected between VIN pins and SW1 pin. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 3 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Block Diagram FSLCT CB1 VIN + OSC SS1 FB1 93% Duty Cycle Limit + DC LIMIT SET + PWM Comp - Soft Start Buck Load Current Measurement RESET BUCK DRIVE Buck Driver SW1 OVP Error Amp + + OVP Comp - TSH PGND Thermal Shutdown BG SHDN1 Bandgap VBG SD Buck 1 Converter VC1 FSLCT CB2 VIN + OSC SS2 FB2 Buck Load Current Measurement DC LIMIT RESET BUCK DRIVE Buck Driver SW2 OVP Error Amp + + OVP Comp BG Bandgap 4 SET + PWM Comp - Soft Start VBG 93% Duty Cycle Limit + VC2 TSH SD PGND Thermal Shutdown SHDN2 Buck 2 Converter Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) VIN -0.3V to 22V SW1 Voltage -0.3V to 22V SW2 Voltage -0.3V to 22V FB1, FB2 Voltages -0.3V to 7V CB1, CB2 Voltages -0.3V to VIN+7V (VIN=VSW) VC1 Voltage 1.75V VC1 2.25V VC2 Voltage 0.965V VC2 1.565V SHDN1 Voltage -0.3V to 7.5V SHDN2 Voltage -0.3V to 7.5V SS1 Voltage -0.3V to 2.1V SS2 Voltage -0.3V to 2.1V FSLCT Voltage AGND to 5V Maximum Junction Temperature 150C Power Dissipation (2) Internally Limited Lead Temperature 300C Vapor Phase (60 sec.) 215C Infrared (15 sec.) ESD Susceptibility (1) (2) (3) (3) 220C Human Body Model 2kV Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended to be functional, but device parameter specifications may not be ensured. For ensured specifications and test conditions, see the Electrical Characteristics table. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, JA, and the ambient temperature, TA. See the Electrical Characteristics table for the thermal resistance. The maximum allowable power dissipation at any ambient temperature is calculated using: PD (MAX) = (TJ(MAX) - TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. Operating Conditions Operating Junction Temperature Range (1) -40C to +125C Storage Temperature -65C to +150C Supply Voltage 4V to 20V SW1 Voltage 20V SW2 Voltage 20V Switching Frequency (1) 300kHz to 600kHz All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% tested or specified through statistical analysis. All limits at temperature extremes are specified via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 5 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Electrical Characteristics Specifications in standard type face are for TJ = 25C and those with boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). VIN = 5V, IL = 0A, and FSW = 300kHz unless otherwise specified. Symbol IQ Parameter Conditions Total Quiescent Current (both switchers) Min (1) Not Switching Typ (2) Max (1) Units 2.7 6 mA Switching, switch open 6 12 mA VSHDN = 0V 9 27 A 1.267 1.294 1.299 V 0.01 0.125 %/V VBG Bandgap Voltage 1.248 1.230 %VBG/VIN Bandgap Voltage Line Regulation VFB1 Buck 1 Feedback Voltage 1.236 1.214 1.258 1.286 1.288 V VFB2 Buck 2 Feedback Voltage 1.236 1.214 1.258 1.286 1.288 V ICL1 (3) Buck 1 Switch Current Limit 1.4 1.65 -0.01 VIN = 8V (4) VIN = 12V, VOUT = 3.3V ICL2 (3) Buck 2 Switch Current Limit VIN = 8V 2.2 (4) VIN = 12V, VOUT = 5V 2.0 3.2 2.6 3.05 3.5 A A IB1 Buck 1 FB Pin Bias Current VIN = 20V 70 400 nA IB2 Buck 2 FB Pin Bias Current VIN = 20V 65 400 nA VIN Input Voltage Range 20 V gm1 Buck 1 Error Amp Transconductance I = 20A gm2 Buck 2 Error Amp Transconductance I = 20A AV1 (5) (5) 4 1340 mho 1360 mho Buck 1 Error Amp Voltage Gain 134 V/V AV2 Buck 2 Error Amp Voltage Gain 136 V/V DMAX Maximum Duty Cycle 89 93 % FSW Switching Frequency RF = 46.4k 240 300 360 kHz RF = 22.6k 480 600 720 kHz ISHDN1 Buck 1 Shutdown Pin Current 0V < VSHDN1 < 7.5V -5 5 A ISHDN2 Buck 2 Shutdown Pin Current 0V < VSHDN2 < 7.5V -5 5 A IL1 Buck 1 Switch Leakage Current VIN = 20V 0.01 5 A IL2 Buck 2 Switch Leakage Current VIN = 20V 0.01 5 A ISW = 100mA 160 180 300 m 160 180 300 m (6) RDSON1 Buck 1 Switch RDSON RDSON2 Buck 2 Switch RDSON (6) ISW = 100mA ThSHDN1 Buck 1 SHDN Threshold Output High 1.8 Output Low (1) (2) (3) (4) (5) (6) 6 1.36 1.33 0.7 V All limits specified at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% tested or specified through statistical analysis. All limits at temperature extremes are specified via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Typical numbers are at 25C and represent the most likely norm. Duty cycle affects current limit due to ramp generator. Current limit at 0% duty cycle. See TYPICAL PERFORMANCE section for Switch Current Limit vs. Input Voltage. Bias current flows into FB pin. Includes the bond wires and package leads, RDSON from VIN pin(s) to SW pin. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 Electrical Characteristics (continued) Specifications in standard type face are for TJ = 25C and those with boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C). VIN = 5V, IL = 0A, and FSW = 300kHz unless otherwise specified. Symbol ThSHDN2 Parameter Buck 2 SHDN Threshold Conditions Output High Min Typ 1.8 1.36 (1) Output Low (2) Max (1) 1.33 0.7 Units V ISS1 Buck 1 Soft Start Pin Current 4 9 15 A ISS2 Buck 2 Soft Start Pin Current 4 9 15 A UVP On Threshold 4 3.8 Off Threshold JA (7) Thermal Resistance (7) 3.6 TSSOP, package only V 3.3 115 C/W Refer to the www.ti.com/packaging for more detailed thermal information and mounting techniques for the TSSOP package. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 7 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics Switching IQ vs. Input Voltage(FSW = 300kHz) 9 14 8 12 7 QUIESCENT CURRENT (mA) QUIESCENT CURRENT (PA) Shutdown IQ vs. Input Voltage 16 10 8 6 4 2 6 5 4 3 2 1 0 4 6 8 10 12 14 16 18 20 0 4 INPUT VOLTAGE (V) 6 8 10 12 14 16 18 20 INPUT VOLTAGE (V) Figure 2. Figure 3. Switching Frequency vs. Input Voltage(FSW = 300kHz) Buck 1 RDS(ON) vs. Input Voltage 320 200 190 315 180 SWITCH RDS(ON) (m: SWITCHING FREQUENCY (kHz) R F = 46.4k 310 305 300 170 160 150 140 130 120 295 110 290 100 4 6 8 10 12 14 16 18 20 4 6 8 12 14 16 18 20 INPUT VOLTAGE (V) Figure 5. Buck 2 RDS(ON) vs. Input Voltage Buck 1 Efficiency vs. Load Current(VOUT = 3.3V) 200 100 190 90 180 80 170 70 160 150 140 V IN = 5V V IN = 12V 60 V IN = 18V 50 40 130 30 120 20 110 10 0 100 4 6 8 10 12 14 16 18 20 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 LOAD CURRENT (A) INPUT VOLTAGE (V) Figure 6. 8 10 Figure 4. EFFICIENCY (%) SWITCH RDS(ON) (m: INPUT VOLTAGE (V) Figure 7. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Buck 2 Efficiency vs. Load Current(VOUT = 5V) 100 100 90 90 80 80 70 70 EFFICIENCY (%) EFFICIENCY (%) Buck 2 Efficiency vs. Load Current(VOUT = 15V) 60 50 40 30 60 50 40 30 20 20 V IN = 18V 10 0 0 0 0.5 1 1.5 2 2.5 0 0.5 1 1.5 2 2.5 LOAD CURRENT (A) LOAD CURRENT (A) Figure 8. Figure 9. Buck 1 Switch Current Limit vs. Input Voltage Buck 2 Switch Current Limit vs. Input Voltage 4 2.4 3.8 2.2 SWITCH CURRENT LIMIT (A) SWITCH CURRENT LIMIT (A) V IN = 18V 10 2 1.8 VOUT = 3.3V 1.6 VOUT = 5V 1.4 1.2 3.6 3.4 VOUT = 3.3V 3.2 3 VOUT = 5V 2.8 2.6 2.4 2.2 1 5 7 9 11 13 15 17 19 5 7 9 11 13 15 17 19 INPUT VOLTAGE (V) INPUT VOLTAGE (V) Figure 10. Figure 11. Buck 1 Switch Current Limit vs. Temperature(VIN = 12V) Buck 2 Switch Current Limit vs. Temperature(VIN = 12V) 3.4 1.65 SWITCH CURRENT LIMIT (A) SWITCH CURRENT LIMIT (A) 1.7 VOUT = 3.3V 1.6 1.55 VOUT = 5V 1.5 1.45 1.4 -40 -20 0 20 40 60 80 3.3 VOUT = 3.3V 3.2 3.1 3 VOUT = 5V 2.9 2.8 -40 AMBIENT TEMPERATURE (oC) Figure 12. -20 0 20 40 60 80 AMBIENT TEMPERATURE (oC) Figure 13. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 9 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Buck 1 Switch ON Resistance vs. Temperature Buck 2 Switch ON Resistance vs. Temperature 250 VIN = 8V POWER SWITCH R DSON (mW) POWER SWITCH R DSON (mW) 300 250 200 150 100 50 0 -40 -20 0 20 40 60 80 VIN = 8V 200 150 100 50 0 -40 -20 100 120 0 20 40 60 80 100 120 JUNCTION TEMPERATURE (C) JUNCTION TEMPERATURE (C) Figure 14. Figure 15. Switching Frequency vs. RF Resistance SWITCHING FREQUENCY (kHz) 700 650 VIN = 12V 600 550 500 450 400 350 300 250 200 20 25 30 35 40 45 50 RF (kW) Figure 16. 10 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 BUCK OPERATION PROTECTION (BOTH REGULATORS) The LM2717-ADJ has dedicated protection circuitry running during normal operation to protect the IC. The Thermal Shutdown circuitry turns off the power devices when the die temperature reaches excessive levels. The UVP comparator protects the power devices during supply power startup and shutdown to prevent operation at voltages less than the minimum input voltage. The OVP comparator is used to prevent the output voltage from rising at no loads allowing full PWM operation over all load conditions. The LM2717-ADJ also features a shutdown mode for each converter decreasing the supply current to approximately 10A (both in shutdown mode). CONTINUOUS CONDUCTION MODE The LM2717-ADJ contains current-mode, PWM buck regulators. A buck regulator steps the input voltage down to a lower output voltage. In continuous conduction mode (when the inductor current never reaches zero at steady state), the buck regulator operates in two cycles. The power switch is connected between VIN and SW1 and SW2. In the first cycle of operation the transistor is closed and the diode is reverse biased. Energy is collected in the inductor and the load current is supplied by COUT and the rising current through the inductor. During the second cycle the transistor is open and the diode is forward biased due to the fact that the inductor current cannot instantaneously change direction. The energy stored in the inductor is transferred to the load and output capacitor. The ratio of these two cycles determines the output voltage. The output voltage is defined approximately as: D= VOUT , D' = (1-D) VIN where * * where D is the duty cycle of the switch D and D will be required for design calculation (1) The LM2717-ADJ has a minimum switch ON time which corresponds to a minimum duty cycle of approximately 10% at 600kHz operation and approximately 5% at 300kHz operation. In the case of some high voltage differential applications (low duty cycle operation) this minimum duty cycle may be exceeded causing the feedback pin over-voltage protection to trip as the output voltage rises. This will put the device into a PFM type operation which can cause an unpredictable frequency spectrum and may cause the average output voltage to rise slightly. If this is a concern the switching frequency may be lowered and/or a pre-load added to the output to keep the device full PWM operation. Note that the OVP function monitors the FB pin so it will not function if the feedback resistor is disconnected from the output. Due to slight differences between the two converters it is recommended that Buck 1 be used for the lower of the two output voltages for best operation. DESIGN PROCEDURE This section presents guidelines for selecting external components. SETTING THE OUTPUT VOLTAGE The output voltage is set using the feedback pin and a resistor divider connected to the output as shown in Figure 20. The feedback pin voltage (VFB) is 1.258V, so the ratio of the feedback resistors sets the output voltage according to the following equation: VOUT - VFB1(2) RFB1(3) = RFB2(4) x VFB1(2) : (2) Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 11 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com INPUT CAPACITOR A low ESR aluminum, tantalum, or ceramic capacitor is needed between the input pin and power ground. This capacitor prevents large voltage transients from appearing at the input. The capacitor is selected based on the RMS current and voltage requirements. The RMS current is given by: (3) The RMS current reaches its maximum (IOUT/2) when VIN equals 2VOUT. This value should be calculated for both regulators and added to give a total RMS current rating. For an aluminum or ceramic capacitor, the voltage rating should be at least 25% higher than the maximum input voltage. If a tantalum capacitor is used, the voltage rating required is about twice the maximum input voltage. The tantalum capacitor should be surge current tested by the manufacturer to prevent being shorted by the inrush current. The minimum capacitor value should be 47F for lower output load current applications and less dynamic (quickly changing) load conditions. For higher output current applications or dynamic load conditions a 68F to 100F low ESR capacitor is recommended. It is also recommended to put a small ceramic capacitor (0.1F to 4.7F) between the input pins and ground to reduce high frequency spikes. INDUCTOR SELECTION The most critical parameter for the inductor in a current mode switcher is the minimum value required for stable operation. To prevent subharmonic oscillations and achieve good phase margin a target minimum value for the inductor is: (D-0.5+2/S)(VIN-VOUT)RDSON LMIN = (H) (1-D)(0.164*FSW) (4) Where VIN is the minimum input voltage and RDSON is the maximum switch ON resistance. For best stability the inductor should be in the range of 0.5LMIN (absolute minimum) and 2LMIN. Using an inductor with a value less than 0.5LMIN can cause subharmonic oscillations. The inductor should meet this minimum requirement at the peak inductor current expected for the application regardless of what the inductor ripple current and output ripple voltage requirements are. A value larger than 2LMIN is acceptable if the ripple requirements of the application require it but it may reduce the phase margin and increase the difficulty in compensating the circuit. The most important parameters for the inductor from an applications standpoint are the inductance, peak current and the DC resistance. The inductance is related to the peak-to-peak inductor ripple current, the input and the output voltages (for 300kHz operation): (5) A higher value of ripple current reduces inductance, but increases the conductance loss, core loss, and current stress for the inductor and switch devices. It also requires a bigger output capacitor for the same output voltage ripple requirement. A reasonable value is setting the ripple current to be 30% of the DC output current. Since the ripple current increases with the input voltage, the maximum input voltage is always used to determine the inductance. The DC resistance of the inductor is a key parameter for the efficiency. Lower DC resistance is available with a bigger winding area. A good tradeoff between the efficiency and the core size is letting the inductor copper loss equal 2% of the output power. OUTPUT CAPACITOR The selection of COUT is driven by the maximum allowable output voltage ripple. The output ripple in the constant frequency, PWM mode is approximated by: (6) The ESR term usually plays the dominant role in determining the voltage ripple. Low ESR ceramic, aluminum electrolytic, or tantalum capacitors (such as MuRata MLCC, Taiyo Yuden MLCC, Nichicon PL series, Sanyo OSCON, Sprague 593D, 594D, AVX TPS, and CDE polymer aluminum) is recommended. An aluminum electrolytic capacitor is not recommended for temperatures below -25C since its ESR rises dramatically at cold temperatures. Ceramic or tantalum capacitors have much better ESR specifications at cold temperature and is preferred for low temperature applications. 12 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 BOOTSTRAP CAPACITOR A 4.7nF ceramic capacitor or larger is recommended for the bootstrap capacitor. For applications where the input voltage is less than twice the output voltage a larger capacitor is recommended, generally 0.1F to 1F to ensure plenty of gate drive for the internal switches and a consistently low RDSON. SOFT-START CAPACITOR (BOTH REGULATORS) The LM2717-ADJ contains circuitry that can be used to limit the inrush current on start-up of the DC/DC switching regulators. This inrush current limiting circuitry serves as a soft-start. The external SS pins are used to tailor the soft-start for a specific application. A current (ISS) charges the external soft-start capacitor, CSS. The soft-start time can be estimated as: TSS = CSS*0.6V/ISS (7) When programming the soft-start time use the equation given in the Soft-Start Capacitor section above. The softstart function is used simply to limit inrush current to the device that could stress the input voltage supply. The soft-start time described above is the time it takes for the current limit to ramp to maximum value. When this function is used the current limit starts at a low value and increases to nominal at the set soft-start time. Under maximum load conditions the output voltage may rise at the same rate as the soft-start, however at light or no load conditions the output voltage will rise much faster as the switch will not need to conduct much current to charge the output capacitor. SHUTDOWN OPERATION (BOTH REGULATORS) The shutdown pins of the LM2717-ADJ are designed so that they may be controlled using 1.8V or higher logic signals. If the shutdown function is not to be used the pin may be left open. The maximum voltage to the shutdown pin should not exceed 7.5V. If the use of a higher voltage is desired due to system or other constraints it may be used, however a 100k or larger resistor is recommended between the applied voltage and the shutdown pin to protect the device. SCHOTTKY DIODE The breakdown voltage rating of D1 and D2 is preferred to be 25% higher than the maximum input voltage. The current rating for the diode should be equal to the maximum output current for best reliability in most applications. In cases where the input voltage is much greater than the output voltage the average diode current is lower. In this case it is possible to use a diode with a lower average current rating, approximately (1-D)*IOUT however the peak current rating should be higher than the maximum load current. LOOP COMPENSATION The general purpose of loop compensation is to meet static and dynamic performance requirements while maintaining stability. Loop gain is what is usually checked to determine small-signal performance. Loop gain is equal to the product of control-output transfer function and the output-control transfer function (the compensation network transfer function). The DC loop gain of the LM2717 is usually around 55dB to 60dB when loaded. Generally speaking it is a good idea to have a loop gain slope that is -20dB /decade from a very low frequency to well beyond the crossover frequency. The crossover frequency should not exceed one-fifth of the switching frequency, i.e. 60kHz in the case of 300kHz switching frequency. The higher the bandwidth is, the faster the load transient response speed will potentially be. However, if the duty cycle saturates during a load transient, further increasing the small signal bandwidth will not help. Since the control-output transfer function usually has very limited low frequency gain, it is a good idea to place a pole in the compensation at zero frequency, so that the low frequency gain will be relatively large. A large DC gain means high DC regulation accuracy (i.e. DC voltage changes little with load or line variations). The rest of the compensation scheme depends highly on the shape of the control-output plot. As shown in Figure 17, the example control-output transfer function consists of one pole (fp), one zero (fz), and a double pole at fn (half the switching frequency). The following can be done to create a -20dB /decade roll-off of the loop gain: Place the first pole at 0Hz, the first zero at fp, the second pole at fz, and the second zero at fn. The resulting output-control transfer function is shown in Figure 18. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 13 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com 20 0 -45 -20 -90 Phase -40 PHASE () GAIN (dB) 0 GAIN (dB) Asymptotic -20 dB/ dec (fp1 is at zero frequency) -20 dB/ dec B fz1 -135 fp2 fz2 FREQUENCY Gain -60 10 100 1k 10k 100k -180 1M FREQUENCY (Hz) Figure 17. Control-Output Transfer Function Figure 18. Output-Control Transfer Function The control-output corner frequencies, and thus the desired compensation corner frequencies, can be determined approximately by the following equations: where * * * Co is the output capacitance Re is the output capacitance ESR f is the switching frequency (8) Co is the output capacitance Ro is the load resistance f is the switching frequency (9) where * * * Since fp is determined by the output network, it will shift with loading (Ro) and duty cycle. First determine the range of frequencies (fpmin/max) of the pole across the expected load range, then place the first compensation zero within that range. Example: Vo = 5V, Re = 20m, Co = 100F, Romax = 5V/100mA = 50, Romin = 5V/1A = 5, L = 10H, f = 300kHz: fz = 2S x 1 = 80 kHz 20 m: x 100 PF (10) 1 + 50: x 100 PF 0.5 = 297 Hz 2S x 300k x 10P x 100 PF (11) 1 + 5: x 100 PF 0.5 = 584 Hz 2S x 300k x 10P x 100 PF (12) fp min = fp max = 2S 2S x x Once the fp range is determined, Rc1 should be calculated using: 14 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 where * * * B is the desired gain in V/V at fp (fz1) gm is the transconductance of the error amplifier 1 and R2 are the feedback resistors as shown in Figure 19 (13) A gain value around 10dB (3.3v/v) is generally a good starting point. Example: B = 3.3 v/v, gm=1350mho, R1 = 20 K, R2 = 59 K: Rc1 = 3.3 x 20k + 59k | 9.76k 1350P 20k (14) Bandwidth will vary proportional to the value of Rc1. Next, Cc1 can be determined with the following equation: (15) Example: fpmin = 297 Hz, Rc1 = 20 K: Cc1 = 2S x 1 | 56 nF 297 Hz x 9.76k (16) The value of Cc1 should be within the range determined by fpmin/max. A higher value will generally provide a more stable loop, but too high a value will slow the transient response time. The compensation network (Figure 19) will also introduce a low frequency pole which will be close to 0Hz. A second pole should also be placed at fz. This pole can be created with a single capacitor Cc2 and a shorted Rc2 (see Figure 19). The minimum value for this capacitor can be calculated by: (17) Cc2 may not be necessary, however it does create a more stable control loop. This is especially important with high load currents. Example: fz = 80 kHz, Rc1 = 20 K: (18) A second zero can also be added with a resistor in series with Cc2. If used, this zero should be placed at fn, where the control to output gain rolls off at -40dB/dec. Generally, fn will be well below the 0dB level and thus will have little effect on stability. Rc2 can be calculated with the following equation: (19) Vo Vc gm CC1 R2 CC2 RC2 RC1 compensation network R1 Figure 19. Compensation Network Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 15 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 www.ti.com Note that the values calculated here give a good baseline for stability and will work well with most applications. The values in some cases may need to be adjusted some for optimum stability or the values may need to be adjusted depending on a particular applications bandwidth requirements. LAYOUT CONSIDERATIONS The LM2717-ADJ uses two separate ground connections, PGND for the drivers and boost NMOS power device and AGND for the sensitive analog control circuitry. The AGND and PGND pins should be tied directly together at the package. The feedback and compensation networks should be connected directly to a dedicated analog ground plane and this ground plane must connect to the AGND pin. If no analog ground plane is available then the ground connections of the feedback and compensation networks must tie directly to the AGND pin. Connecting these networks to the PGND can inject noise into the system and effect performance. The input bypass capacitor CIN, as shown in Figure 20, must be placed close to the IC. This will reduce copper trace resistance which effects input voltage ripple of the IC. For additional input voltage filtering, a 0.1F to 4.7F bypass capacitors can be placed in parallel with CIN, close to the VIN pins to shunt any high frequency noise to ground. The output capacitors, COUT1 and COUT2, should also be placed close to the IC. Any copper trace connections for the COUTX capacitors can increase the series resistance, which directly effects output voltage ripple. The feedback network, resistors RFB1(3) and RFB2(4), should be kept close to the FB pin, and away from the inductor to minimize copper trace connections that can inject noise into the system. Trace connections made to the inductors and schottky diodes should be minimized to reduce power dissipation and increase overall efficiency. For more detail on switching power supply layout considerations see Application Note AN-1149: Layout Guidelines for Switching Power Supplies (SNVA021). APPLICATION INFORMATION Table 1. Some Recommended Inductors (Others May Be Used) Manufacturer Inductor Contact Information Coilcraft DO3316 and DT3316 series www.coilcraft.com 800-3222645 TDK SLF10145 series www.component.tdk.com 847-803-6100 Pulse P0751 and P0762 series www.pulseeng.com Sumida CDRH8D28 and CDRH8D43 series www.sumida.com Table 2. Some Recommended Input And Output Capacitors (Others May Be Used) 16 Manufacturer Capacitor Vishay Sprague 293D, 592D, and 595D series tantalum www.vishay.com Taiyo Yuden High capacitance MLCC ceramic www.t-yuden.com Cornell Dubilier ESRD seriec Polymer Aluminum Electrolytic SPV and AFK series V-chip series www.cde.com MuRata High capacitance MLCC ceramic www.murata.com Submit Documentation Feedback Contact Information Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 RFB2 RFB1 20k 33.2k 4.7 nF U1 CSS1 CC1 47 nF 20k 4.7 nF RC1 CBG 1 nF CC2 2k 4.7 nF RC2 CSS2 RF L1 22 mH CBOOT1 22.6k 47 nF AGND CB1 SW1 FB1 SHDN1 SS1 VC1 VIN VBG VIN VC2 SHDN2 CB2 SS2 FSLCT AGND AGND FB2 D1 MBRS240 *Connect CINA (pin 23) and CINB (pins 14,15) as close as possible to the VIN pins. VIN CBOOT2 1 mF PGND PGND PGND COUT1A 1 mF ceramic COUT1 68 mF 17V to 20V IN *CINB 4.7 mF ceramic *CINA 4.7 mF ceramic CIN 68 mF L2 22 mH 15V OUT2 SW2 PGND AGND 3.3V OUT1 D2 MBRS240 RFB3 221k COUT2A 1 mF ceramic COUT2 68 mF LM2717-ADJ RFB4 20k PGND Figure 20. 15V, 3.3V Output Application RFB2 RFB1 20k 33.2k 1 mF U1 CSS1 CC1 47 nF 20k 4.7 nF RC1 CBG 1 nF CC2 10k 4.7 nF RC2 CSS2 47 nF AGND RF L1 22 mH CBOOT1 22.6k CB1 SW1 FB1 SHDN1 SS1 VC1 VIN VIN VC2 SHDN2 CB2 SS2 FSLCT AGND AGND FB2 D1 MBRS240 *Connect CINA (pin 23) and CINB (pins 14,15) as close as possible to the VIN pins. VIN VBG CBOOT2 1 mF PGND PGND PGND COUT1A 1 mF ceramic COUT1 68 mF 8V to 20V IN *CINB 4.7 mF ceramic *CINA 4.7 mF ceramic CIN 68 mF L2 22 mH SW2 PGND AGND 3.3V OUT1 D2 MBRS240 5V OUT2 RFB3 59k COUT2A 1 mF ceramic COUT2 68 mF LM2717-ADJ RFB4 20k PGND Figure 21. 5V, 3.3V Output Application Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 17 LM2717-ADJ SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 RFB2 www.ti.com 20.5k 8.66k 1 mF U1 CSS1 CC1 47 nF 2k 82 nF RC1 CBG 1 nF CC2 2k 82 nF RC2 CSS2 RF L1 10 mH CBOOT1 RFB1 22.6k 47 nF AGND CB1 SW1 FB1 SHDN1 SS1 VC1 VIN VIN VBG VIN VC2 SHDN2 CB2 SS2 FSLCT AGND AGND FB2 *Connect CINA (pin 23) and CINB (pins 14,15) as close as possible to the VIN pins. CBOOT2 1 mF *CINB 4.7 mF ceramic D1 MBRS240 AGND PGND PGND COUT1A 47 mF ceramic COUT1 47 mF ceramic 5V to 15V IN *CINA 4.7 mF ceramic CIN 68 mF L2 10 mH SW2 PGND PGND 1.8V OUT1 D2 MBRS240 3.3V OUT2 RFB3 33.2k COUT2A 47 mF ceramic COUT2 47 mF ceramic LM2717-ADJ RFB4 20k PGND Figure 22. 3.3V, 1.8V Output Application 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ LM2717-ADJ www.ti.com SNVS407C - DECEMBER 2005 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision B (March 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM2717-ADJ 19 PACKAGE OPTION ADDENDUM www.ti.com 7-Oct-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) LM2717MT-ADJ/NOPB ACTIVE TSSOP PW 24 61 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM2717 MT-ADJ LM2717MTX-ADJ/NOPB ACTIVE TSSOP PW 24 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM2717 MT-ADJ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM2717MTX-ADJ/NOPB Package Package Pins Type Drawing TSSOP PW 24 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 16.4 Pack Materials-Page 1 6.95 B0 (mm) K0 (mm) P1 (mm) 8.3 1.6 8.0 W Pin1 (mm) Quadrant 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2717MTX-ADJ/NOPB TSSOP PW 24 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated