SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 1 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
3.5x2.7mm SURFACE MOUNT LED LAMP
Part Number: AA3527ASES-50MAV
Super Bright Orange
Features
zSingle color.
zSuitable for all SMT assembly and solder process.
zAvailable on tape and reel.
zIdeal for backlighting.
zPackage : 2000pcs / reel.
zMoisture sensitivity level : level 3.
zRoHS compliant.
Description
The Super Bright Orange device is made with AlGaInP (on
GaAs substrate) light emitting diode chip.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 2 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
1. Handle the component along the side surfaces by using forceps or appropriate tools.
2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.
3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or
damage the internal circuitry.
4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.
4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.
4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup
and avoid damage during production.
5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of
leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.
Handling Precautions
Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic
significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.
As a result, special handling precautions need to be observed during assembly using silicone encapsulated
LED products. Failure to comply might lead to damage and premature failure of the LED.
All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 3 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
Selection Guide
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Notes:
1.Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Part No. Dice Lens Type
Iv (mcd) [2]
@ 50mA
V
iewing
Angle [1]
Min. Typ. 2θ1/2
AA3527ASES-50MAV Super Bright Orange (AlGaInP) Water Clear
500 1000
*300 *500
120°
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Super Bright Orange 610 nm IF=50mA
λD [1] Dominant Wavelength Super Bright Orange 601 nm IF=50mA
Δλ1/2 Spectral Line Half-width Super Bright Orange 29 nm IF=50mA
C Capacitance Super Bright Orange 30 pF VF=0V;f=1MHz
VF [2] Forward Voltage Super Bright Orange 2.1 2.6 V IF=50mA
IR Reverse Current Super Bright Orange 10 uA VR=5V
Parameter Super Bright Orange Units
Power dissipation 130 mW
DC Forward Current 50 mA
Peak Forward Current [1] 195 mA
Reverse Voltage 5 V
Operating Temperature -40°C To +85°C
Storage Temperature -40°C To +85°C
SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 4 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
Super Bright Orange AA3527ASES-50MAV
SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 5 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
AA3527ASES-50MAV
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAL6322 REV NO: V.2A DATE: MAR/02/2013 PAGE: 6 OF 6
APPROVED: WYNEC CHECKED: Allen Liu DRAWN: F.Cui ERP: 1201007602
PACKING & LABEL SPECIFICATIONS AA3527ASES-50MAV
