24V DRIVE INTERFACE BOARD (PARALLEL) FTP-622DCL001/011/101/111 FOR FTP-622/632/642MCL001/002/301/302/303/304 INTERFACE 1. Centronics (1) Connector (CN1) Connector part number : FCN-605Q030-G/S (Fujitsu Components) Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent (2) Connector pin assignment No. Signal I/O Contents No. Signal I/O Contents 1 PRSTB I Data strobe 2 PRSTB-RET -- Connected to logic GND 3 PRDT0 I Data 0 4 PRDT0-RET -- Connected to logic GND 5 PRDT1 I Data 1 6 PRDT1-RET -- Connected to logic GND 7 PRDT2 I Data 2 8 PRDT2-RET -- Connected to logic GND 9 PRDT3 I Data 3 10 PRDT3-RET -- Connected to logic GND 11 PRDT4 I Data 4 12 PRDT4-RET -- Connected to logic GND 13 PRDT5 I Data 5 14 PRDT5-RET -- Connected to logic GND 15 PRDT6 I Data 6 16 PRDT6-RET -- Connected to logic GND 17 PRDT7 I Data 7 18 PRDT7-RET -- Connected to logic GND 19 ACKNLG O Data input acknowledge 20 ACKNLG-RET -- Connected to logic GND 21 BUSY O Busy 22 BUSY-RET -- Connected to logic GND 23 RINF2 O Printer status 24 INPRM-RET -- Connected to logic GND 25 SLCTIN I Printer select 26 INPRM I Reset 27 RINF1 O Printer status 28 RINF3 O Printer status 29 ATF I Paper feed request 30 GND -- Logic GND Notes: * Symbol "----" means a negative logic signal. * "-RET" signal is a return signal of the twisted pair cable. * "I" or "O" means a signal direction from the interface board side. (4) Data input signal timing (3) Connector pin number PRDT0~7 t1 FCN-605Q030-G/S (Fujitsu Components) or equivalent No.1 t3 PRSTB t2 BUSY t4 ACKNLG No.30 t5 No.2 Data set time :t10.5 sec PRSTB pulse :t20.5 sec Data hold time :t30.5 sec 104 PRSTB to BUSY= "H" :t40.5 sec . ACKNLG pulse :t5=5.0 sec . FTP-622DCL001/011/101/111 CONNECTOR PIN ASSIGNMENT 1. Connector for power supply (CN10) Part number : B6P-VH (J.S.T) Mating connector part number : VHR-6N (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VCC -- Power supply for logic (+5 V) 2 GND -- GND (5 V, 24 V common) 3 GND -- GND (5 V, 24 V common) 4 GND -- GND (5 V, 24 V common) 5 VDD -- Power for head/motor (+24 V) 6 V DD -- Power for head/motor (+24 V) 2. Connector for thermal head drive (CN8) Part number : B16B-PH-K-S (J.S.T) Mating connector part number : PHR-16 (J.S.T) or equivalent No. Signal I/O Contents No. Signal I/O Contents 1 VDH O Power for head (+24 V) 2 VDH O Power for head (+24 V) 3 GND (VDH) -- Head GND 4 GND (VDH) -- Head GND 5 STB1 O Print enable signal 1 6 STB2 O Print enable signal 2 7 STB3 O Print enable signal 3 8 TMP I Temperature detection signal 9 STB4 O Print enable signal 4 10 LAT O Print data latch signal 11 STB5 O Print enable signal 5 12 5 VH O Power for logic (+5 V) 13 HCLK O Data transmission clock 14 HD O Print data output signal 15 GND (VDH) -- Head GND 16 VDH O Power for head (+24 V) Notes: * Symbol "----" means a negative logic signal. * "I" or "O" means a signal direction from the interface board side. 3. Connector for Sensor (CN3) Part number No. Signal : B5B-PH-K-S (J.S.T) I/O Contents No. Signal I/O 1 +5 V -- Power for logic (+5 V) 2 PES I 3 GND (5 V) -- Logic GND 4 +5 V -- 5 HUP I Contents Paper end detect signal Power for logic (+5 V) Head-up detect signal 2 FTP-622DCL001/011/101/111 4. Connector for paper near end detection (CN5) Part number : B2B-PH-K-S (J.S.T) Mating connector part number : PHR-2 (J.S.T) or equivalent No. 1 Signal +5 V I/O -- Contents Power for logic (+5 V) No. 2 Signal NES I/O I Contents Paper near end detect signal 5. Connector for stepping motor drive (CN13) Part number No. Signal : B4B-PH-K-S (J.S.T) I/O Contents No. Signal I/O Contents 1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation 3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation 6. Connector for cutter drive (CN11) *1 Part number No. Signal : B4B-EH (J.S.T) I/O Contents No. Signal I/O Contents 1 SW1 I Cutter position detect signal 2 GND -- Logic ground 3 M+ O Motor control signal (+) 4 M- O Motor control signal (-) *1: Only for FTP-622DCL011/111. 3 FTP-622DCL001/011/101/111 PRINTING COMMANDS (CENTRONICS INTERFACE) Command Contents HT Moves the print position to the next tab. LF Line feed. FF Feeds forms (new page). ESC RS Sets reverse printing. ESC US Resets reverse printing. ESC ! +n Sets print mode. ESC* +m+n1+n2+d1~dN Sets the bit image mode "m" for n1, n2 dot numbers. ESC 2 Sets 1/6 inch line feed length. ESC 3 + n Sets the line feed length. ESC @ Printer initialization. ESC A+n Sets the space between lines. ESC C+n Sets the page length by character line. ESC D+d1~dN+NUL Sets the tab position. ESC J+n Feeds paper in forward direction. ESC K+n Feeds paper in reverse direction. ESC c+1+n Sets the internal processing. ESC R+n Selects the international character. ESC s+n Sets the printing speed. ESC d+n Printing and n-line feeding. ESC e+n Reverse line feed in "n" lines after printing. ESC t+n Character code table selection. ESC {+n Sets/resets the upside down printing. ECS EM+n Automatic paper feed distance setting. ESC X+n+m Setting turning time of the motor excitation. ESC V+n Right Rotation 90 specification / cancellation. FS E+n Correction of impressed energy. FS ! +n Sets the Kanji print mode*1. FS & Sets Kanji mode*1. FS . Resets Kanji mode*1. FS C+n Selects Kanji code type*1. (Continued) 4 FTP-622DCL001/011/101/111 (Continued) Command Contents FS 9+n Sets the detection functions. FS W+n Sets/resets 4 times enlarged character. GS < Line feeds to the next mark. GS A+m+n Sets the line feed length after mark detection. GS E+n Sets print quality. GS V+n+m Executes paper cutting*2. GS e+n+m Sets the bar width. GS h+n Sets the barcode height. GS k+m+n+d1~dN Selects the barcode type and prints. GS w+n Sets the barcode length. GS &+m+x+y1+y2+[d]k Registration of image data.. GS '+m+n Prints registered image data.. GS a+n Sets and cancels status transmission (valid only for DSL). *2: Only for FTP-622DCL011/111. 5 FTP-622DCL001/011/101/111 OPTIONS 1. Cable (With FTP-622MCL, FTP-632MCL, FTP-642MCL) Name Part Number Cable Length Thermal head connection cable (CN8)* FTP-622Y001 270 mm (10.6 inches) Interface cable FTP-622Y201 500 mm (19.71 inches) Power cable for head, motor, and logic (CN10) FTP-622Y401 300 mm (11.8 inches) * short cable option FTP-624Y001 150 mm (5.9 inches) Centronics (CN1) 2. Paper holder Name Part number Flange FTP-040HF Stand FTP-040HS Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: www.fceu.fujitsu.com North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: marcom@fcai.fujitsu.com Web: www.fcai.fujitsu.com Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #04-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com www.fcal.fujitsu.com (c) 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered trademarks of their respective owners. Rev. 06/2002 6