24V DRIVE INTERFACE BOARD (PARALLEL)
FTP-622DCL001/011/101/111
1. Centronics
(1) Connector (CN1)
Connector part number : FCN-605Q030-G/S (Fujitsu Components)
Mating connector part number : FCN-607B030-G/D (Fujitsu Components) or equivalent
No. Signal I/O Contents No. Signal I/O Contents
1 PRSTB I Data strobe 2 PRSTB-RET
Connected to logic GND
3 PRDT0 I Data 0 4 PRDT0-RET
Connected to logic GND
5 PRDT1 I Data 1 6 PRDT1-RET
Connected to logic GND
7 PRDT2 I Data 2 8 PRDT2-RET
Connected to logic GND
9 PRDT3 I Data 3 10 PRDT3-RET
Connected to logic GND
11 PRDT4 I Data 4 12 PRDT4-RET
Connected to logic GND
13 PRDT5 I Data 5 14 PRDT5-RET
Connected to logic GND
15 PRDT6 I Data 6 16 PRDT6-RET
Connected to logic GND
17 PRDT7 I Data 7 18 PRDT7-RET
Connected to logic GND
19 ACKNLG O Data input acknowledge 20 ACKNLG-RET
Connected to logic GND
21 BUSY O Busy 22 BUSY-RET
Connected to logic GND
23 RINF2 O Printer status 24 INPRM-RET
Connected to logic GND
25 SLCTIN I Printer select 26 INPRM I Reset
27 RINF1 O Printer status 28 RINF3 O Printer status
29 ATF I Paper feed request 30 GND Logic GND
(2) Connector pin assignment
Notes:
• Symbol “——” means a negative logic signal.
• “–RET” signal is a return signal of the twisted pair cable.
• “I” or “O” means a signal direction from the interface board side.
INTERFACE
(3) Connector pin number
FCN-605Q030-G/S (Fujitsu Components) or
equivalent
(4) Data input signal timing
No.1
No.2
No.30
PRDT0~7
PRSTB
BUSY
ACKNLG
t1 t3
t2
t4
t5
:t10.5 µsec
:t20.5 µsec
:t30.5 µsec
PRSTB to BUSY= “H”
ACKNLG pulse :t40.5 µsec
:t5=5.0 µsec
..
Data set time
PRSTB pulse
Data hold time
104
FOR FTP-622/632/642MCL001/002/301/302/303/304
2
FTP-622DCL001/011/101/111
CONNECTOR PIN ASSIGNMENT
1. Connector for power supply (CN10)
Part number : B6P-VH (J.S.T)
Mating connector part number : VHR-6N (J.S.T) or equivalent
No. Signal I/O Contents No. Signal I/O Contents
1VCC Power supply for logic (+5 V) 2 GND GND (5 V, 24 V common)
3 GND GND (5 V, 24 V common) 4 GND GND (5 V, 24 V common)
5VDD Power for head/motor (+24 V) 6 V DD Power for head/motor (+24 V)
2. Connector for thermal head drive (CN8)
Part number : B16B-PH-K-S (J.S.T)
Mating connector part number : PHR-16 (J.S.T) or equivalent
No. Signal I/O Contents No. Signal I/O Contents
1 VDH O Power for head (+24 V) 2 VDH O Power for head (+24 V)
3
GND (VDH)
Head GND 4
GND (VDH)
Head GND
5 STB1 O Print enable signal 1 6 STB2 O Print enable signal 2
7 STB3 O Print enable signal 3 8 TMP I Temperature detection signal
9 STB4 O Print enable signal 4 10 LAT O Print data latch signal
11 STB5 O Print enable signal 5 12 5 VH O Power for logic (+5 V)
13 HCLK O Data transmission clock 14 HD O Print data output signal
15
GND (VDH)
Head GND 16 VDH O Power for head (+24 V)
Notes:
• Symbol “——” means a negative logic signal.
• “I” or “O” means a signal direction from the interface board side.
3. Connector for Sensor (CN3)
Part number : B5B-PH-K-S (J.S.T)
No. Signal I/O Contents No. Signal I/O Contents
1 +5 V Power for logic (+5 V) 2 PES I Paper end detect signal
3
GND (5 V)
Logic GND 4 +5 V Power for logic (+5 V)
5 HUP I Head-up detect signal
3
FTP-622DCL001/011/101/111
No. Signal I/O Contents No. Signal I/O Contents
1 MT/B O Stepping motor coil excitation 2 MT/B O Stepping motor coil excitation
3 MT/A O Stepping motor coil excitation 4 MT/A O Stepping motor coil excitation
No. Signal I/O Contents No. Signal I/O Contents
1 +5 V Power for logic (+5 V) 2 NES I Paper near end detect signal
5. Connector for stepping motor drive (CN13)
Part number : B4B-PH-K-S (J.S.T)
4. Connector for paper near end detection (CN5)
Part number : B2B-PH-K-S (J.S.T)
Mating connector part number : PHR-2 (J.S.T) or equivalent
6. Connector for cutter drive (CN11) *1
Part number : B4B-EH (J.S.T)
No. Signal I/O Contents No. Signal I/O Contents
1 SW1 I Cutter position detect signal 2 GND Logic ground
3 M+ O Motor control signal (+) 4 M- O Motor control signal (-)
*1: Only for FTP-622DCL011/111.
4
FTP-622DCL001/011/101/111
PRINTING COMMANDS (CENTRONICS INTERFACE)
(Continued)
Command Contents
HT Moves the print position to the next tab.
LF Line feed.
FF Feeds forms (new page).
ESC RS Sets reverse printing.
ESC US Resets reverse printing.
ESC ! +n Sets print mode.
ESC* +m+n1+n2+d1~dNSets the bit image mode “m” for n1, n2 dot numbers.
ESC 2 Sets 1/6 inch line feed length.
ESC 3 + n Sets the line feed length.
ESC @ Printer initialization.
ESC A+n Sets the space between lines.
ESC C+n Sets the page length by character line.
ESC D+d1~dN+NUL Sets the tab position.
ESC J+n Feeds paper in forward direction.
ESC K+n Feeds paper in reverse direction.
ESC c+1+n Sets the internal processing.
ESC R+n Selects the international character.
ESC s+n Sets the printing speed.
ESC d+n Printing and n-line feeding.
ESC e+n Reverse line feed in “n” lines after printing.
ESC t+n Character code table selection.
ESC {+n Sets/resets the upside down printing.
ECS EM+n Automatic paper feed distance setting.
ESC X+n+m Setting turning time of the motor excitation.
ESC V+n Right Rotation 90° specification / cancellation.
FS E+n Correction of impressed energy.
FS ! +n Sets the Kanji print mode*1.
FS & Sets Kanji mode*1.
FS . Resets Kanji mode*1.
FS C+n Selects Kanji code type*1.
5
FTP-622DCL001/011/101/111
Command Contents
FS 9+n Sets the detection functions.
FS W+n Sets/resets 4 times enlarged character.
GS < Line feeds to the next mark.
GS A+m+n Sets the line feed length after mark detection.
GS E+n
Sets print quality
.
GS V+n+m Executes paper cutting*2.
GS e+n+m Sets the bar width.
GS h+n Sets the barcode height.
GS k+m+n+d1~dNSelects the barcode type and prints.
GS w+n Sets the barcode length.
GS &+m+x+y1+y2+[d]k Registration of image data..
GS '+m+n Prints registered image data..
GS a+n Sets and cancels status transmission (valid only for DSL).
(Continued)
*2: Only for FTP-622DCL011/111.
6
FTP-622DCL001/011/101/111
OPTIONS
1. Cable (With FTP-622MCL, FTP-632MCL, FTP-642MCL)
2. Paper holder
emaNrebmuNtraPhtgneLelbaC
*)8NC(elbacnoitcennocdaehlamrehT 100Y226-PTF)sehcni6.01(mm072
elbacecafretnI)1NC(scinortneC102Y226-PTF)sehcni17.91(mm005
)01NC(cigoldna,rotom,daehrofelbacrewoP 104Y226-PTF)sehcni8.11(mm003
noitpoelbactrohs* 100Y426-PTF)sehcni9.5(mm051
Name Part number
Flange FTP-040HF
Stand FTP-040HS
© 2002 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 06/2002
Japan
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: promothq@ft.ed.fujitsu.com
Web: www.fcl.fujitsu.com
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fax: (1-408) 745-4970
Email: marcom@fcai.fujitsu.com
Web: www.fcai.fujitsu.com
Europe
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: info@fceu.fujitsu.com
Web: www.fceu.fujitsu.com
Asia Pacific
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (65) 6273-3021
Email: fcal@fcal.fujitsu.com
www.fcal.fujitsu.com
Fujitsu Components
International
Headquarter
Offices