Device Selection Guide
Viewing Angle Dominant
Package Description 2θ1/2 Wavelength
Rectangular, 2mm x 110 615 nm
5mm, Tinted, Diffused
2 mm x 5 mm Rectangular
AlInGaP Lamps
Technical Data
HLMA-SH05
Features
• Rectangular Light
Emitting Surface
• Excellent for Flush
Mounting on Panels
• Long Life: Solid State
Reliability
• Excellent Uniformity of
Light Output
Description
The HLMA-SH05 is an epoxy
encapsulated lamp in
rectangular package which are
easily stacked in arrays or used
for discrete front panel indi-
cators. Contrast and light
uniformity are enhanced by a
special epoxy diffusion and
tinting process.
Technology
This 2x5 rectangular solid state
lamp utilizes the newly
developed Aluminum Indium
Gallium Phosphide (AlInGaP)
LED technology. This material
has a very high luminous
efficiency, capable of producing
high light output over a wide
range of drive currents.
Package Dimensions
5.18 (0.204)
4.93 (0.194) 5.46 (0.215)
4.95 (0.195)
26.40 (1.00)
MIN.
8.00 (0.315)
7.37 (0.290)
1.27 (0.060)
NOMINAL
2.41 (0.095)
2.03 (0.085)
2.23 (0.088)
1.98 (0.078) SIDE VIEW
BOTTOM VIEW
0.46 (0.018) SQ.
NOMINAL
2.54 (0.100)
NOMINAL
CATHODE
LEAD
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES).
2. AN EPOXY MENISCUS MAY EXTEND ABOUT
1 mm (0.040") DOWN THE LEADS.
3. THERE IS A MAXIMUM 1° TAPER FROM
BASE TO THE TOP OF LAMP.
2
Absolute Maximum Ratings
DC Forward Current[1] .............................................................. 50 mA
Peak Forward Current[2] ......................................................... 200 mA
Average Forward Current ......................................................... 45 mA
(at IPEAK = 200 mA, f ≥ 1 KHz)[2]
Transient Forward Current[3] ................................................. 500 mA
(10 µs Pulse)
Reverse Voltage (IR = 100 µA) ........................................................ 5 V
LED Junction Temperature ...................................................... 110°C
Operating Temperature Range ..................................... -40 to +100°C
Storage Temperature Range ......................................... -55 to +100°C
Soldering Temperature ....................................... 260°C for 5 seconds
(1.59 mm [0.06 in]) below seating plane)
Notes:
1. Derate linearly as shown in Figure 4.
2. Refer to Figure 5 to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device
can withstand without damaging the LED die and wire bonds.
Figure 3. Relative Luminous
Intensity vs. Foward Current. Figure 5. Maximum Average
Current vs. Peak Foward Current.
Figure 2. Forward Current vs.
Forward Voltage.
Figure 1. Relative Intensity vs. Wavelength.
Figure 4. Maximum Forward
Current vs. Ambient Temperature.
Derating Based on T Max = 110°C.
WAVELENGTH – nm
RELATIVE INTENSITY
550 594 600 650 700
1.0
0.5
0
AMBER
630
REDDISH
ORANGE
621
20
V
F
– FORWARD VOLTAGE – V
2
10
50
0 3.52.5
5
1
200
100
I
F
– FORWARD CURRENT – mA
1.0 1.5 3.00.5
0.5 2.0
RELATIVE LUMINOUS INTENSITY
(NORMALIZED AT 20 mA)
0
0
I
F
– DC FORWARD CURRENT – mA
20 40
2.5
1.5
1.0
10 30
2.0
50
0.5
IF – FORWARD CURRENT – mA
0
0
TA – AMBIENT TEMPERATURE – °C
40 80
50
40
30
20
10
20 60 100
RθJA = 618 °C/W
RθJA = 412 °C/W
5
15
25
35
45
10 30 50 70 90
I
AVG
– AVERAGE CURRENT – mA
50
0
I
PEAK
– PEAK FORWARD CURRENT – mA
150
60
40
30
20
10
100 200
f > 1 KHz
f > 300 Hz
f > 100 Hz
50
3
Optical Characteristics at TA = 25°C
Luminous Color, Viewing
Intensity Peak Dominant Angle Luminous
IV (mcd) Wavelength Wavelength 2θ1/2 Efficacy
Part Number @ 20 mA λpeak (nm) λd[1] (nm) Degrees[2] ηv
HLMA- Min. Typ. Typ. Typ. Typ. (lm/w)
SH05 8 20 621 615 110 263
Notes:
1. The dominant wavelength, λd, is derived from the CIE Chromaticity Diagram and represents the color of the device.
2. θ1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity.
Electrical Characteristics at TA = 25°C
Speed of
Forward Reverse Capacitance Response
Voltage Breakdown C (pF) τs (ns)
Part VF (Volts) VR (Volts) VF = 0, Thermal Time Constant
Number @ IF = 20 mA @ IR = 100 µA f = 1 MHz Resistance e-t/τ
HLMA- Min. Typ. Min. Typ. Typ. RθJ-PIN (°C/W) Typ.
SH05 1.9 2.4 5 20 40 260 13
s
Figure 6.
NORMALIZED INTENSITY
1.0
0
ANGULAR DISPLACEMENT – DEGREES
0.8
0.6
0.5
0.7
0.2
100°90°
0.1
0.3
0.4
80°70° 60° 50° 40° 20° 10° 0°30° 10° 20° 30° 40° 50° 60° 70° 80° 90°100°
0.9
www.agilent.com/semiconductors
For product information and a complete list of
distributors, please go to our web site.
For technical assistance call:
Americas/Canada: +1 (800) 235-0312 or
(408) 654-8675
Europe: +49 (0) 6441 92460
China: 10800 650 0017
Hong Kong: (+65) 271 2451
India, Australia, New Zealand: (+65) 271 2394
Japan: (+81 3) 3335-8152(Domestic/Interna-
tional), or 0120-61-1280(Domestic Only)
Korea: (+65) 271 2194
Malaysia, Singapore: (+65) 271 2054
Taiwan: (+65) 271 2654
Data subject to change.
Copyright © 2002 Agilent Technologies, Inc.
Obsoletes 5962-6935E
April 2, 2002
5988-4387EN
