BACKSHELLS
NOVEMBER 2013
AND CONNECTOR ACCESSORIES—FROM AS85049 TO MIL-DTL-38999
THE WORLD'S MOST COMPLETE SELECTION OF MIL-SPEC
Most customers have a simple expectation when they go shopping for
safety-critical interconnect components: they want fast and accurate
service. Glenair stocks tens of thousands of qualied mil-spec backshells
and connector accessories—bagged and tagged and ready for immediate
shipment. In fact, Glenair is the world’s largest manufacturer and supplier of
mil-spec backshells and connector accessories with more listed QPL’s and more
manufacturing experience than any other supplier. You have a simple expectation:
fast and accurate service. At Glenair, we’re ready to give you exactly that. It’s a
promise.
Tens of thousands of parts in-stock
and ready for immediate shipment
Glenair, Inc.
1211 Air Way
Glendale, CA
91201-2497
818-247-6000
sales@glenair.com
www.glenair.com
QUALIFIED
MILSPEC Connector Backshells
and Accessories
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
Military Standard Backshells and Accessories
A
B
C
D
E
F
G
H
J
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/123 M85049/123 –– 620FA038 90° Strain Relief, Self-Locking or
Non-Self-Locking “F”
MIL-DTL-38999 Series I & II;
MIL-DTL-27599 B-130
AS85049/124 M85049/124 –– 620HS038 Sraight Strain Relief, Self-Locking or
Non-Self-Locking “H”
MIL-DTL-38999 Ser. III & IV
EN3645 B-132
AS85049/126 M85049/126 –– 620HA038 90° Strain Relief, Self-Locking or
Non-Self-Locking “H”
MIL-DTL-38999 Ser. III & IV
EN3645 B-134
AS85049/127 M85049/127 –– 687-581 Bushing Strip –– B-136
AS85049/128-3
AS85049/128-4 M85049/128-3
M85049/128-4 –– 600-052
600-052-1 Standard Clamping Band
Precoiled Standard Clamping Band AS85049/128 B-137
AS85049/130 M85049/130 –– Consult Factory Gasket –– B-138
AS85049/139 M85049/139 MS3420 GS85049/139
687 Telescoping Bushing, C or L –– B-140
AS85049/140 M85049/140-05
M85049/140-09
M85049/140-20
M85049/140-25 MS3109 770-003S107
770-006S102W1
770-007S104
770-018S102
Straight Lipped Heat Shrink Boot
Str. Lipped Long Tail Low Prole H.S. Boot
Str. Lipped Mini. Long Tail Low Prole H.S. Boot
Straight Lipped Sealing Heat Shrink Boot ––
B-142
B-144
B-146
B-148
AS85049/141 M85049/141-03
M85049/141-10
M85049/141-19 MS3117 770-003A105
770-006A103
770-007A103
90° Lipped Heat Shrink Boot
90° Lipped Low Prole Heat Shrink Boot
90° Lipped Mini. Low Prole Heat Shrink Boot –– B-150
B-152
B-154
AS85049/142 M85049/142-02
M85049/142-05
M85049/142-10 –– 770-011T102
770-010Y105
770-013110W1
Tee Transition Wide Body Heat Shrink Boot
Wye Transition Wide Body Heat Shrink Boot
1:3 Transition Wide Body Heat Shrink Boot –– B-156
B-158
B-160
SECTION C • MIL-DTL-38999 QUALIFIED PRODUCTS • SECTION C
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-38999
MIL-DTL-38999 MS27501
MS27502 MS20048
MS20047 660-012
660-013 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series I C-2
MIL-DTL-38999 MS27510
MS27511 MS27352
MS27353 660-014
660-015 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series II C-3
MIL-DTL-38999/22 D38999/22 –– 650HS010 Dummy Storage Receptacle, Threaded Coupling MIL-DTL-38999, Series III C-4
MIL-DTL-38999/28 D38999/28 –– Consult Factory Jam Nut with Safety Wire Holes MIL-DTL-38999 Series III & IV;
EN3645 C-5
MIL-DTL-38999/32
MIL-DTL-38999/33 D38999/32
D38999/33 –– 660-023
660-024 Composite or Metal Threaded Plug Cover
Composite or Metal Threaded Receptacle Cover MIL-DTL-38999, Series III C-6
MIL-DTL-38999/50 D38999/50 –– 650HS007 Dummy Storage Receptacle, Bayonet Coupling MIL-DTL-38999, Series IV C-7
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION D • MIL-DTL-28840 QUALIFIED PRODUCTS • SECTION D
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-28840/1 M28840/1 –– 620GS051 Straight Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-2
MIL-DTL-28840/2 M28840/2 –– 620GA051 90° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-3
MIL-DTL-28840/3 M28840/3 –– 620GB051 45° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-4
MIL-DTL-28840/4 M28840/4 –– –– Metal-Core Conduit “G”
MIL-DTL-28840 D-5
MIL-DTL-28840/5 M28840/5 –– –– Straight Backshell for Metal-Core Conduit “G”
MIL-DTL-28840 D-6
MIL-DTL-28840/6 M28840/6 A
M28840/6 B –– 390AB001
370 Series Strt. EMI/RFI Environmental Backshell, Style A
Straight Environmental Backshell, Style B “G”
MIL-DTL-28840 D-7
D-8
MIL-DTL-28840/7 M28840/7 –– 650GS001 Dummy Storage Receptacle, Threaded Coupling “G”
MIL-DTL-28840 D-9
MIL-DTL-28840/8 M28840/8-
M28840/8 A –– 390-061 90° Environmental Backshell, Style A
90° EMI/RFI Environmental Backshell, Style B “G”
MIL-DTL-28840 D-10
D-11
MIL-DTL-28840/9 M28840/9 B
M28840/9 A –– 390-061 45° Environmental Backshell, Style A
45° EMI/RFI Environmental Backshell “G”
MIL-DTL-28840 D-12
D-13
MIL-DTL-28840/13
MIL-DTL-28840/15 M28840/13
M28840/15 –– 660-010
660-011 Protective Threaded Receptacle Cover
Protective Threaded Plug Cover MIL-DTL-28840 D-14
MIL-DTL-28840/22 M28840/22 –– –– Metal-Core Conduit Bushing “G”
MIL-DTL-28840 D-15
MIL-DTL-28840/23 M28840/23 –– Consult Factory E Nut, Non-Self-Locking “G”
MIL-DTL-28840 D-16
MIL-DTL-28840/24 M28840/24 –– Consult Factory Gasket “G”
MIL-DTL-28840 D-17
SECTION E • MIL-DTL-83723 QUALIFIED PRODUCTS • SECTION E
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-83723/27 M83723/27M –– 310KS002 Straight Shrink Boot Adapter “K”
MIL-DTL-83723 Series II E-2
MIL-DTL-83723/35 M83723/35S
M83723/35A
M83723/35N –– Consult Factory Strt. Non-Environmental Strain Relief Backshell
90° Non-Environmental Strain Relief Backshell
Non-Self-Locking E-Nut “K”
MIL-DTL-83723 Series II
E-3
E-4
E-5
MIL-DTL-83723/50 M83723/50 R
M83723/50 B
M83723/50 A –– Consult Factory Straight Qwik-Ty
®
Strain Relief
45° Qwik-Ty
®
Strain Relief
90° Qwik-Ty
®
Strain Relief K”
MIL-DTL-83723 Series II E-6
MIL-DTL-83723/59
MIL-DTL-83723/60 M83723/59-1
M83723/60-1 MS27292
MS27293 660-021
660-022 Protective Plug Cover, Threaded Coupling
Protective Receptacle Cover, Threaded Coupling MIL-DTL-83723, Series III E-7
MIL-DTL-83723/59
MIL-DTL-83723/60 M83723/59-2
M83723/60-2 MS27294
MS27295 660-019
660-020 Protective Plug Cover Bayonet Coupling
Protective Receptacle Cover Bayonet Coupling MIL-DTL-83723, Series III E-8
MIL-DTL-83723/70 M83723/70 –– Consult Factory Straight Quick Disconnect Receptacle Adapter –– E-9
Part Number Index and Introduction
AS85049 Qualied Backshells and Connector Accessories
MIL-DTL-38999 Qualied Connector Accessories
MIL-DTL-28840 Qualied Backshells and Connector Accessories
MILDTL83723 Qualied Backshells and Connector Accessories
AS81511 Qualied Backshells and Connector Accessories
Miscellaneous Qualied Backshells and Connector Accessories
Backshell-to-Connector Assembly Tools
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Quick Reference
P/N to Page No.
I
Quick-Reference
Military Standard Backshells and Accessories
Quick-Reference Part Number to Page Number Index
Part Number Page
AS25042
AS25043 G-2
AS50151 G-8
AS81511/13 F-2
AS81511/14 F-3
AS81511/14 F-5
AS81511/17
AS81511/18 F-7
AS81511/19 F-8
AS81511/20 F-9
AS81511/29 F-7
AS81511/30 F-10
AS85049/1 B-2
AS85049/2 B-3
AS85049/3 B-4
B-5
B-6
AS85049/4 B-7
B-9
B-11
AS85049/5 B-13
B-15
B-17
AS85049/6 B-19
AS85049/7 B-21
AS85049/8 B-23
AS85049/9 B-25
AS85049/10 B-27
AS85049/11 B-31
AS85049/14 B-35
AS85049/15 B-36
AS85049/16 B-36
AS85049/17 B-37
AS85049/18 B-38
AS85049/19 B-39
AS85049/20 B-41
AS85049/21 B-42
AS85049/23 B-43
AS85049/24 B-45
AS85049/25 B-47
AS85049/26 B-51
B-52
AS85049/27 B-53
AS85049/28 B-54
Part Number Page
AS85049/29 B-55
AS85049/30 B-56
AS85049/31 B-57
AS85049/33 B-58
AS85049/34 B-59
AS85049/36 B-60
AS85049/37 B-61
AS85049/38 B-62
AS85049/39 B-63
AS85049/41 B-64
AS85049/42 B-65
AS85049/43 B-66
AS85049/44 B-67
AS85049/45 B-68
AS85049/46 B-69
AS85049/47 B-70
AS85049/48 B-71
B-72
B-73
AS85049/49 B-74
AS85049/50 B-75
AS85049/51 B-76
AS85049/52 B-77
AS85049/53
AS85049/54
AS85049/55 B-78
AS85049/56
AS85049/57 B-79
AS85049/58 B-80
AS85049/59 B-81
AS85049/60 B-82
B-83
AS85049/61 B-84
AS85049/62 B-85
AS85049/63 B-86
AS85049/69 B-87
AS85049/74 B-88
AS85049/75 B-89
AS85049/76 B-90
AS85049/77 B-91
AS85049/78 B-92
AS85049/79 B-93
AS85049/80 B-94
Part Number Page
AS85049/81 B-96
AS85049/82
AS85049/83
AS85049/84 B-97
AS85049/85
AS85049/86
AS85049/87 B-99
AS85049/88
AS85049/89
AS85049/90 B-101
AS85049/91
AS85049/92 B-103
AS85049/93 B-104
AS85049/94 B-105
AS85049/95 B-106
AS85049/96 B-107
AS85049/103 B-108
AS85049/104 B-110
AS85049/105 B-112
AS85049/109 B-114
AS85049/111 B-116
AS85049/112 B-118
AS85049/114 B-120
AS85049/115 B-122
AS85049/118 B-124
AS85049/120 B-126
AS85049/121 B-128
AS85049/123 B-130
AS85049/124 B-132
AS85049/126 B-134
AS85049/127 B-136
AS85049/128-3
AS85049/128-4 B-137
AS85049/130 B-138
AS85049/139 B-140
AS85049/140
B-142
B-144
B-146
B-148
AS85049/141 B-150
B-152
B-154
AS85049/142 B-156
B-158
B-160
MIL-DTL-26500 G-5
Part Number Page
MIL-DTL-26500 G-6
MIL-DTL-28840/1 D-2
MIL-DTL-28840/2 D-3
MIL-DTL-28840/3 D-4
MIL-DTL-28840/4 D-5
MIL-DTL-28840/5 D-6
MIL-DTL-28840/6 D-7
D-8
MIL-DTL-28840/7 D-9
MIL-DTL-28840/8 D-10
D-11
MIL-DTL-28840/9 D-12
D-13
MIL-DTL-28840/13
MIL-DTL-28840/15 D-14
MIL-DTL-28840/22 D-15
MIL-DTL-28840/23 D-16
MIL-DTL-28840/24 D-17
MIL-DTL-38999
MIL-DTL-38999 C-2
MIL-DTL-38999 C-3
MIL-DTL-38999/22 C-4
MIL-DTL-38999/28 C-5
MIL-DTL-38999/32
MIL-DTL-38999/33 C-6
MIL-DTL-38999/50 C-7
MIL-DTL-83513/05 G-15
MIL-DTL-83538/9 G-16
MIL-DTL-83723/27 E-2
MIL-DTL-83723/35 E-3
E-4
E-5
MIL-DTL-83723/50 E-6
MIL-DTL-83723/59
MIL-DTL-83723/60 E-7
MIL-DTL-83723/59
MIL-DTL-83723/60 E-8
MIL-DTL-83723/70 E-9
MIL-S-81824/1 G-17
MS17349
MS17350 G-3
MS27291 G-4
Quick-Reference Part Number Index
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-2
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/1 M85049/1 MS3057 “B” 620-053 Style B Straight Strain Relief MS “V” Thread B-2
AS85049/2 M85049/2 MS3057 “C” 620-053 Style C Straight Environmental Strain Relief MS “V” Thread B-3
AS85049/3
M85049/3 Style 1
M85049/3 Style 2
M85049/3 Style 3
MS17340/MS90571 Style 1
MS17340/MS90571 Style 2
MS17340/MS90571 Style 3
GS85049/3
377 Straight Environmental Backshell “C”
MIL-DTL-22992, C, J & R
B-4
B-5
B-6
AS85049/4
M85049/4 Style 1
M85049/4 Style 2
M85049/4 Style 3
MS17342/MS90569 Style 1
MS17342/MS90569 Style 2
MS17342/MS90569 Style 3
GS85049/4
377 Straight Step-Up Environmental Backshell “C”
MIL-DTL-22992, C, J & R
B-7
B-9
B-11
AS85049/5
M85049/5 Style 1
M85049/5 Style 2
M85049/5 Style 3
MS17341/MS90570 Style 1
MS17341/MS90570 Style 2
MS17341/MS90570 Style 3
377-034 Straight Step-Down Environmental Backshell “C”
MIL-DTL-22992, C, J & R
B-13
B-15
B-17
AS85049/6 M85049/6 MS3189A 390AB001 45° RFI/EMI Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-19
AS85049/7 M85049/7 MS3189B 370AB001 45° Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-21
AS85049/8 M85049/8 MS3188A 390AA001 90° RFI/EMI Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-23
AS85049/9 M85049/9 MS3188B 360-061 90° Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-25
AS85049/10 M85049/10 MS3437A 390AS001 Straight RFI/EMI Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-27
AS85049/11 M85049/11 MS3437B 370AS001 Straight Environmental Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-31
AS85049/14
M85049/14-
M85049/14 N
M85049/14 S
MIL-C-85049/14 610HS011
E Nut
E Nut, Non-Detented, Self Locking
E Nut, Detented, Self-Locking
“H”
MIL-DTL-38999, Ser. III & IV
EN3645
B-35
AS85049/15
M85049/15-
M85049/15 N
M85049/15 S
M85049/15 G
M85049/15 H
MIL-C-85049/15
450HB001
450HB041
450HB043
450HB043 “G”
450HB041 “G”
45° Qwik-Ty® Strain Relief
Non-Detented, Self-Locking
Detented Self-Locking
Detented, Self-Locking, Ground Lug
Non-Detented Self-Locking, Ground Lug
“H”
MIL-DTL-38999, Ser. III & IV;
EN3645
B-36
AS85049/16
M85049/16-
M85049/16 N
M85049/16 S
M85049/16 G
M85049/16 H
MIL-C-85049/16
450HA001
450HA041
450HA043
450HA043 “G”
450HA041 “G”
90° Qwik-Ty® Strain Relief
Non-Detented, Self-Locking
Detented Self-Locking
Detented, Self-Locking, Ground Lug
Non-Detented Self-Locking, Ground Lug
“H”
MIL-DTL-38999, Ser. III & IV;
EN3645
B-36
AS85049/17 M85049/17 MIL-C-38999/5 390FS012 Straight RFI/EMI Environmental Backshell “F”
MIL-DTL-38999 Series I & II B-37
AS85049/18 M85049/18 MIL-C-85049/18 390HS011 Straight RFI/EMI Environmental Backshell
“H”
MIL-DTL-38999, Ser. III & IV;
EN3645
B-38
AS85049/19 M85049/19 MIL-C-85049/19 380HS007 Straight Environmental Backshell
“H”
MIL-DTL-38999, Ser. III & IV;
EN3645
B-39
Rev. 5/30/14
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/20 M85049/20 MIL-C-85049/20 440HS063 Straight Crimp Ring Backshell and Crimp Ring “H”
MIL-DTL-38999, Ser . III & IV;
EN3645 B-41
AS85049/21 M85049/21 MIL-C-85049/21 360HS002 Straight Non-Environmental Strain Relief
Backshell “H”
MIL-DTL-38999, Ser . III & IV;
EN3645 B-42
AS85049/23 M85049/23 MS3189C 380AB001 45° RFI-EMI Non-Environmental Backshell “A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-43
AS85049/24 M85049/24 MS3188C 390AA001 90° RFI-EMI Non-Environmental Backshell “A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-45
AS85049/25 M85049/25 MS3437C 380AS001 Straight RFI-EMI Non-Environmental Backshell “A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-47
AS85049/26 M85049/26-1
M85049/26-2
M85049/26-3
MS3419
MS3161
MIL-C-85049/26-3 440AS063
687-150 Adapter Only
Crimp Ring Only
Adapter with Crimp Ring
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-51
B-52
AS85049/27 M85049/27-
M85049/27 N
M85049/27 S MIL-DTL-38999/1 610FS011 E Nut
E Nut, Non-Detented, Self-Locking
E Nut, Detented, Self-Locking “F”
MIL-DTL-38999 Series I & II B-53
AS85049/28 M85049/28 M83733/15 G61570 Strt. Rectangular Non-Environmental Backshell –– B-54
AS85049/29 M85049/29 MIL-DTL-38999/6 360FS002 Straight Non-Environmental Strain Relief
Backshell “F”
MIL-DTL-38999 Series I & II B-55
AS85049/30 M85049/30 MIL-DTL-38999/4 400FS001 Straight RFI-EMI Individual
Shield Termination Backshell “F”
MIL-DTL-38999 Series I & II B-56
AS85049/31 M85049/31-
M85049/31 N
M85049/31 S MS3416 610AS011 E Nut
E Nut, Non-Detented, Self-Locking
E Nut, Detented, Self Locking
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-57
AS85049/33 M85049/33-2 MIL-DTL-38999/2 440FS063 Straight Crimp Ring Non-Environmental
Backshell “F”
MIL-DTL-38999 Series I & II B-58
AS85049/34 M85049/34 MS3484 320 Straight Adapter and Extender
For use with MS3114 & MS3124 Connectors “D”
MIL-DTL-26482 Series I B-59
AS85049/36 M85049/36 MIL-DTL-38999/7 380FS008 Straight RFI-EMI Non-Environmental Backshell “F”
MIL-DTL-38999 Series I & II B-60
AS85049/37 M85049/37 MIL-DTL-38999/8 380FD007 90° RFI-EMI Non-Environmental Backshell “F”
MIL-DTL-38999 Series I & II B-61
AS85049/38 M85049/38 N
M85049/38 S MIL-C-85049/38- 620HS011
620HS048 Str. Strain Relief, Non-Detented Self-Locking
Straight Strain Relief, Detented Self-Locking ““H”
MIL-DTL-38999 Series III & IV
EN3645 B-62
AS85049/39 M85049/39 MIL-C-85049/39 620HA011
620HA048 90° Strain Relief, Non-Detented Self-Locking
90° Strain Relief, Detented Self-Locking “H”
MIL-DTL-38999 Series III & IV;
EN3645 B-63
AS85049/41 M85049/41 MS3057A 620-053 Style A Straight Strain Relief MS “V” Thread B-64
AS85049/42 M85049/42 MS3057D 620-053 Style H Straight Strain Relief MS “V” Thread B-65
AS85049/43 M85049/43 MS3415 620AB047 45° Strain Relief –– B-66
AS85049/44 M85049/44 M83733/16 G61257 Straight Rectangular Strain Relief Backshell –– B-67
AS85049/45 M85049/45 MS27663 440FS037 Straight Strain Relief “F”
MIL-DTL-38999 Series I & II B-68
AS85049/46 M85049/46 MS27663 440FA037 90° Non-Self-Locking Composite Strain Relief “F”
MIL-DTL-38999 Series I & II B-69
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/47 M85049/47 MS27507 620FA012 90° Self-Locking or Non-Self-Locking Strain
Relief “F”
MIL-DTL-38999 Series I & II B-70
AS85049/48 M85049/48-1
M85049/48-2
M85049/48-3
M24308/20
M24308/21
M24308/22 GS85049/48
550/557 Rectangular Strain Relief Backshell MIL-DTL-24308 B-71
B-72
B-73
AS85049/49 M85049/49-2 MS27506 620FS054 Straight Strain Relief “F”
MIL-DTL-38999 Series I & II B-74
AS85049/50 M85049/50 MS24308/19 GS85049/50
550/557 Rectangular Strain Relief Backshell MIL-DTL-24308 B-75
AS85049/51 M85049/51 MS3418 620AA046 90° Self-Locking or Non-Self-Locking
Strain Relief
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-76
AS85049/52 M85049/52 MS3417 620AS046 Straight Self-Locking or Non-Self-Locking
Strain Relief
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-77
AS85049/53
AS85049/54
AS85049/55
M85049/53
M85049/54
M85049/55
MS3152
MS3153
MS3154
450AS001
450BS001
450AA001
Straight Qwik-Ty® Strain Relief
45° Qwik-Ty® Strain Relief
90° Qwik-Ty® Strain Relief
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-78
AS85049/56
AS85049/57 M85049/56
M85049/57 MS27668
MS27669 450FS001
450FB001 Straight Qwik-Ty® Strain Relief
45° Qwik-Ty® Strain Relief “F”
MIL-DTL-38999 Ser. I & II B-79
AS85049/58 M85049/58 MS27485 GS85049/58
310 Potting Boot Ring “F”
MIL-DTL-38999 Ser. I & II B-80
AS85049/59 M85049/59 MS90568 310CS002 Straight Shrink Boot Adapter “C”
MIL-DTL-22992 B-81
AS85049/60 M85049/60-1
M85049/60-2G MS3158
MS3416 310AS001
310AS002 Straight Shrink Boot Adapter
Straight Shrink Boot Adapter “A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-82
B-83
AS85049/61 M85049/61 MS27332 GS85049/61
310 Potting Boot Ring MIL-DTL-27599 B-84
AS85049/62 M85049/62 M38999/2 310FS001 Straight Shrink Boot Adapter “F”
MIL-DTL-38999 Ser. I & II B-85
AS85049/63 M85049/63 MS27670 450FA001 90° Qwik-Ty® Strain Relief “F”
MIL-DTL-38999 Ser. I & II B-86
AS85049/69 M85049/69 MIL-C-85049/69 310HS001 Straight Shrink Boot Adapter “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-87
AS85049/74 M85049/74 MS27333 GS85049/74
687 Potting Boot for Use with AS85049/61
Potting Boot Ring (Page B-84) –– B-88
AS85049/75 M85049/75 MS27486 GS85049/75
687 Potting Boot for Use with AS85049/58
Potting Boot Ring (Page B-80) –– B-89
AS85049/76 M85049/76 MIL-C-85049/76 390FL011 90° EMI/RFI Environmental Backshell “F”
MIL-DTL-38999 Ser. I & II B-90
AS85049/77 M85049/77 MIL-C-85049/77 390FK011 45° EMI/RFI Environmental Backshell “F”
MIL-DTL-38999 Ser. I & II B-91
AS85049/78 M85049/78 MIL-C-85049/78 390HK011 45° EMI/RFI Environmental Backshell “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-92
AS85049/79 MIL-C-85049/79 390HL011 390HL011 90° EMI/RFI Environmental Backshell “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-93
AS85049/80 M85049/80 MIL-C-85049/80 GS85049/80
687 Sealing Plug, Sizes 8, 12 and 16 MIL-DTL-38999 B-94
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/81 M85049/81 MIL-C-85049/81 GS85049/81
687 Sealing Plug MIL-DTL-38999 B-96
AS85049/82
AS85049/83
AS85049/84
M85049/82
M85049/83
M85049/84
MIL-C-85049/82
MIL-C-85049/83
MIL-C-85049/84
440AS069
440AH069
440AJ069
Straight Banding Backshell
45° Banding Backshell
90° Banding Backshell
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-97
AS85049/85
AS85049/86
AS85049/87
M85049/85
M85049/86
M85049/87
MIL-C-85049/85
MIL-C-85049/86
MIL-C-85049/87
440FS069
440FH069
440FJ069
Straight Banding Backshell
45° Banding Backshell
90° Banding Backshell
“F”
MIL-DTL-38999
Series I & I B-99
AS85049/88
AS85049/89
AS85049/90
M85049/88
M85049/89
M85049/90
MIL-C-85049/88
MIL-C-85049/89
MIL-C-85049/90
440HS069
440HH069
440-HJ069
Straight Banding Backshell
45° Banding Backshell
90° Banding Backshell
“H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-101
AS85049/91
AS85049/92 M85049/91
M85049/92 MIL-C-85049/91
MIL-C-85049/92 620HS042
620HA042 Straight Strain Relief
90° Strain Relief “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-103
AS85049/93 M85049/93 MIL-C-85049/93 687-207 Banding Split Ring –– B-104
AS85049/94 M85049/94 MIL-C-88528/1 GS85049/94
687 Full Perimeter Mounting Flange –– B-105
AS85049/95 M85049/95 MIL-C-88528/2 GS85049/95
687 3/4 Perimeter Mounting Flange –– B-106
AS85049/96 M85049/96 MIL-C-88528/3 GS85049/96
687 1/4 Perimeter Mounting Flange –– B-107
AS85049/103 M85049/103 –– 447HS557 Straight Shield Sock Composite Adapter with
Detented or Non-Detented Self-Locking
Coupling Nut
“H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-108
AS85049/104 M85049/104 –– 447HB557 45° Shield Sock Composite Adapter with
Detented or Non-Detented Self-Locking
Coupling Nut
“H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-110
AS85049/105 M85049/105 –– 447HA557 90° Shield Sock Composite Adapter with
Detented or Non-Detented Self-Locking
Coupling Nut
“H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-112
AS85049/109 M85049/109 88064 319AS001 Straight Shield Sock Shrink Boot Adapter with
Detented or Non-Detented Self-Locking or
Non-Self Locking Coupling Nut
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-114
AS85049/111 M85049/111 89018 319AJ001 90° Shield Sock Sock Shrink Boot Adapter with
Optional Self-Locking Coupling Nut
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-116
AS85049/112 M85049/112 89014 319FS001 Straight Shield Sock Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut “F”
MIL-DTL-38999 Series I & II B-118
AS85049/114 M85049/114 89016 319FJ001 90° Shield Sock Shrink Boot Adapter with
Detented or Non-Detented Self-Locking
Coupling Nut “F”
MIL-DTL-38999 Series I & II B-120
AS85049/115 M85049/115 89013 319HS001 Straight Shield Sock Shrink Boot Adapter with
Optional Self-Locking Coupling Nut “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-122
AS85049/118 M85049/118 –– 620AS038 Straight Strain Relief, Self-Locking or
Non-Self-Locking
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-124
AS85049/120 M85049/120 –– 620AA038 90° Strain Relief, Self-Locking or
Non-Self-Locking
“A”
AS50151; MIL-DTL-26482,
Series 2; AS81703 Series 3;
MIL-DTL-83723, Series III
B-126
AS85049/121 M85049/121 –– 620FS038 Straight Strain Relief, Self-Locking or
Non-Self-Locking “F”
MIL-DTL-38999 Series I & II;
MIL-DTL-27599 B-128
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION B • AS85049 QUALIFIED PRODUCTS • SECTION B
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS85049/123 M85049/123 –– 620FA038 90° Strain Relief, Self-Locking or
Non-Self-Locking “F”
MIL-DTL-38999 Series I & II;
MIL-DTL-27599 B-130
AS85049/124 M85049/124 –– 620HS038 Sraight Strain Relief, Self-Locking or
Non-Self-Locking “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-132
AS85049/126 M85049/126 –– 620HA038 90° Strain Relief, Self-Locking or
Non-Self-Locking “H”
MIL-DTL-38999 Ser . III & IV
EN3645 B-134
AS85049/127 M85049/127 –– 687-581 Bushing Strip –– B-136
AS85049/128-3
AS85049/128-4 M85049/128-3
M85049/128-4 –– 600-052
600-052-1 Standard Clamping Band
Precoiled Standard Clamping Band AS85049/128 B-137
AS85049/130 M85049/130 –– Consult Factory Gasket –– B-138
AS85049/139 M85049/139 MS3420 GS85049/139
687 Telescoping Bushing, C or L –– B-140
AS85049/140 M85049/140-05
M85049/140-09
M85049/140-20
M85049/140-25 MS3109 770-003S107
770-006S102W1
770-007S104
770-018S102
Straight Lipped Heat Shrink Boot
Str. Lipped Long Tail Low Prole H.S. Boot
Str. Lipped Mini. Long Tail Low Prole H.S. Boot
Straight Lipped Sealing Heat Shrink Boot ––
B-142
B-144
B-146
B-148
AS85049/141 M85049/141-03
M85049/141-10
M85049/141-19 MS3117 770-003A105
770-006A103
770-007A103
90° Lipped Heat Shrink Boot
90° Lipped Low Prole Heat Shrink Boot
90° Lipped Mini. Low Prole Heat Shrink Boot –– B-150
B-152
B-154
AS85049/142 M85049/142-02
M85049/142-05
M85049/142-10 –– 770-011T102
770-010Y105
770-013110W1
Tee Transition Wide Body Heat Shrink Boot
Wye Transition Wide Body Heat Shrink Boot
1:3 Transition Wide Body Heat Shrink Boot –– B-156
B-158
B-160
SECTION C • MIL-DTL-38999 QUALIFIED PRODUCTS • SECTION C
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-38999
MIL-DTL-38999 MS27501
MS27502 MS20048
MS20047 660-012
660-013 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series I C-2
MIL-DTL-38999 MS27510
MS27511 MS27352
MS27353 660-014
660-015 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series II C-3
MIL-DTL-38999/22 D38999/22 –– 650HS010 Dummy Storage Receptacle, Threaded Coupling MIL-DTL-38999, Series III C-4
MIL-DTL-38999/28 D38999/28 –– Consult Factory Jam Nut with Safety Wire Holes MIL-DTL-38999 Series III & IV;
EN3645 C-5
MIL-DTL-38999/32
MIL-DTL-38999/33 D38999/32
D38999/33 –– 660-023
660-024 Composite or Metal Threaded Plug Cover
Composite or Metal Threaded Receptacle Cover MIL-DTL-38999, Series III C-6
MIL-DTL-38999/50 D38999/50 –– 650HS007 Dummy Storage Receptacle, Bayonet Coupling MIL-DTL-38999, Series IV C-7
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION D • MIL-DTL-28840 QUALIFIED PRODUCTS • SECTION D
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-28840/1 M28840/1 –– 620GS051 Straight Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-2
MIL-DTL-28840/2 M28840/2 –– 620GA051 90° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-3
MIL-DTL-28840/3 M28840/3 –– 620GB051 45° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-4
MIL-DTL-28840/4 M28840/4 –– –– Metal-Core Conduit “G”
MIL-DTL-28840 D-5
MIL-DTL-28840/5 M28840/5 –– –– Straight Backshell for Metal-Core Conduit “G”
MIL-DTL-28840 D-6
MIL-DTL-28840/6 M28840/6 A
M28840/6 B –– 390AB001
370 Series
Strt. EMI/RFI Environmental Backshell, Style A
Straight Environmental Backshell, Style B
“G”
MIL-DTL-28840
D-7
D-8
MIL-DTL-28840/7 M28840/7 –– 650GS001 Dummy Storage Receptacle, Threaded Coupling “G”
MIL-DTL-28840 D-9
MIL-DTL-28840/8 M28840/8-
M28840/8 A –– 390-061 90° Environmental Backshell, Style A
90° EMI/RFI Environmental Backshell, Style B
“G”
MIL-DTL-28840
D-10
D-11
MIL-DTL-28840/9 M28840/9 B
M28840/9 A –– 390-061 45° Environmental Backshell, Style A
45° EMI/RFI Environmental Backshell
“G”
MIL-DTL-28840
D-12
D-13
MIL-DTL-28840/13
MIL-DTL-28840/15
M28840/13
M28840/15 –– 660-011
660-010
Protective Threaded Receptacle Cover
Protective Threaded Plug Cover MIL-DTL-28840 D-14
MIL-DTL-28840/22 M28840/22 –– –– Metal-Core Conduit Bushing “G”
MIL-DTL-28840 D-15
MIL-DTL-28840/23 M28840/23 –– Consult Factory E Nut, Non-Self-Locking “G”
MIL-DTL-28840 D-16
MIL-DTL-28840/24 M28840/24 –– Consult Factory Gasket “G”
MIL-DTL-28840 D-17
SECTION E • MIL-DTL-83723 QUALIFIED PRODUCTS • SECTION E
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-83723/27 M83723/27M –– 310KS002 Straight Shrink Boot Adapter “K”
MIL-DTL-83723 Series II E-2
MIL-DTL-83723/35
M83723/35S
M83723/35A
M83723/35N
–– Consult Factory
Strt. Non-Environmental Strain Relief Backshell
90° Non-Environmental Strain Relief Backshell
Non-Self-Locking E-Nut
“K”
MIL-DTL-83723 Series II
E-3
E-4
E-5
MIL-DTL-83723/50
M83723/50 R
M83723/50 B
M83723/50 A
–– Consult Factory
Straight Qwik-Ty® Strain Relief
45° Qwik-Ty® Strain Relief
90° Qwik-Ty® Strain Relief
K”
MIL-DTL-83723 Series II E-6
MIL-DTL-83723/59
MIL-DTL-83723/60
M83723/59-1
M83723/60-1
MS27292
MS27293
660-021
660-022
Protective Plug Cover, Threaded Coupling
Protective Receptacle Cover, Threaded Coupling MIL-DTL-83723, Series III E-7
MIL-DTL-83723/59
MIL-DTL-83723/60
M83723/59-2
M83723/60-2
MS27294
MS27295
660-019
660-020
Protective Plug Cover Bayonet Coupling
Protective Receptacle Cover Bayonet Coupling MIL-DTL-83723, Series III E-8
MIL-DTL-83723/70 M83723/70 –– Consult Factory Straight Quick Disconnect Receptacle Adapter –– E-9
Rev. 5/30/14
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-8
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Rev 8-19-14 Printed in U.S.A.
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION F • AS81511 QUALIFIED PRODUCTS • SECTION F
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS81511/13 M81511/13 –– 620JS001 Straight Non-Self-Locking Strain Relief “J”
AS81511 Series I, II, III & IV F-2
AS81511/14 M81511/14 A
M81511/14 B –– 390JS012
390JS012
Straight EMI/RFI Environmental Backshell A
Straight EMI/RFI Environmental Backshell B
“J”
AS81511 Series I, II, III & IV F-3
AS81511/14 M81511/14 C
M81511/14 D –– 380JS008
380JS008
Str. EMI/RFI Non-Environmental Backshell C
Str. EMI/RFI Non-Environmental Backshell D
“J”
AS81511 Series I, II, III & IV F-5
AS81511/17
AS81511/18
M81511/17
M81511/18 –– 660-017
660-018
Protective Plug Cover
Protective Receptacle Cover AS81511 Series I, II, III & IV F-7
AS81511/19 M81511/19 –– 650JS002 Dummy Storage Receptacle AS81511 Series I, II, III & IV F-8
AS81511/20 M81511/20 –– Consult Factory Jam Nut AS81511 Series I, II, III & IV F-9
AS81511/29 M81511/29 –– 660-016 Protective Plug Cover AS81511 Series I, II, III & IV F-7
AS81511/30 M81511/30 –– 650JS001 Dummy Storage Receptacle Bayonet Coupling MIL-DTL-26500 and
MIL-DTL-83723, Series III F-10
SECTION G • MISCELLANEOUS QUALIFIED PRODUCTS • SECTION G
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS25042
AS25043
MS25042
MS25043
MS25042
MS25043
660-004
660-005
Threaded Protective Plug Cover
Threaded Protective Receptacle Cover AS50151 G-2
MS17349
MS17350
MS17349
MS17350 –– 660-007
660-006
Threaded Protective Receptacle Cover
Threaded Protective Plug Cover MIL-DTL-22992 G-3
MS27291 MS27291 –– 620ES050 Straight Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-4
MIL-DTL-26500 MS27558 –– G2221-A 90° Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-5
MIL-DTL-26500 MS27559 –– G2221-B 90° Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-6
–– MS27741 –– 410-003 TAG® Ring for Reliable Terminations –– G-7
AS50151 MS3105 –– 650BS001 Dummy Storage Receptacle, Threaded Coupling AS50151 G-8
–– MS3115 –– 650DS001 Dummy Storage Receptacle, Bayonet Coupling MIL-DTL-26482 G-9
–– MS3180
MS3181 –– 660-008
660-009
Protective Plug Cover, Bayonet Coupling
Protectiove Receptacle Cover, Bayonet Coupling MIL-DTL-26482 G-10
–– MS27512 MS3186 Consult Factory Jam Nut with Safety Wire Holes
AS50151; MIL-DTL-26482;
MIL-DTL-26500;
MIL-DTL-83723 Series I;
MIL-DTL-83723, Series III
MIL-DTL-38999 Series I;
MIL-DTL38999 Series II;
MIL-DTL-28840;
MIL-DTL-27599
G-11
–– M29504/04 –– Consult Factory Fiber Optic Pin Terminus, Size 16 MIL-DTL-29504 G-13
–– M29504/05 –– Consult Factory Fiber Optic Socket Terminus, Size 16 MIL-DTL-29504 G-14
MIL-DTL-83513/05 M83513/05 –– Consult Factory Micro-D Jackscrew Kits MIL-DTL-83513/05 G-15
MIL-DTL-83538/9 M83538/9S –– Consult Factory Straight Adapter and Extender MIL-DTL-83538/4 G-16
MIL-S-81824/1 M81824/1 –– 070-001 In-Line Splice, Insulated and Environmental –– G-17
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-9
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Backshells and Accessories
Part and Page Number Index
SECTION H • GLENAIR QUALIFIED TOOLS • SECTION H
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
–– –– –– TG37 Connector Wrench for MIL-DTL-26500 and
MIL-DTL-83723 Series III MIL-DTL-26500;
MIL-DTL-83723 Series III H-2
–– MS3481 –– TG39 Connector Wrench for MIL-DTL-26482,
Ser . I & II; MIL-DTL-83723, Ser. I & NAS 1599 MIL-DTL-26482 Ser i e s I & I I ;
MIL-DTL-83723 Series I;
NAS 1599 H-3
–– –– –– TG47 Connector Wrench for MIL-DTL-22992,
Classes C, J and R MIL-DTL-22992,
Classes C, J and R H-4
–– –– –– TG48 Connector Wrench for MIL-DTL-38999, Series II MIL-DTL-38999 Series II H-5
–– –– –– TG52 Connector Wrench for MIL-C-81511,
Series II and IV MIL-C-81511 Series II & IV H-6
–– –– –– TG60 Connector Wrench for MIL-DTL-27599 and
MIL-DTL-38999, Series I MIL-DTL-27599;
MIL-DTL-38999 Series I H-7
–– –– –– TG83 Wrench for SJT Connectors (LN29729) LN29729 H-8
–– –– –– TG90 Connector Wrench For MIL-DTL-38999, Ser III MIL-DTL-38999 Series III H-9
–– –– –– 600B005 Plug and Receptacle Holder for
MIL-DTL-5015555 Series MS3100 Solder & Crimp
and MIL-DTL-83723, Series II
MIL-DTL-50155 Series MS3100
Solder and Crimp;
MIL-DTL-83723 Series II H-10
–– –– –– 600C005 Plug and Receptacle Holder for
MIL-DTL-22992 Classes C, J and R MIL-DTL-22992
Classes C, J and R H-11
–– –– –– 600D005 Plug and Receptacle Holder for
MIL-DTL-26482, Series I and II,
MIL-DTL-83723, Series I and NAS 1599
MIL-DTL-26482 Series I & II;
MIL-DTL-83723 Series I;
NAS 1599 H-12
–– –– –– 600E005 Plug and Receptacle Holder for MIL-DTL-26500
and MIL-DTL-83723 Series III MIL-DTL-26500;
MIL-DTL-83723 Series III H-13
–– –– –– 600F005 Plug and Receptacle Holder for MIL-DTL-27599
and MIL-DTL-38999 Series I MIL-DTL-27599;
MIL-DTL-38999 Series I H-14
–– –– –– 600FF005 Plug and Receptacle Holder for
MIL-DTL-38999, Series II MIL-DTL-38999 Series II H-15
–– –– –– 600G005 Plug and Recetacle Holder for MIL-DTL-28840 MIL-DTL-28840 H-16
–– –– –– 600H005 Plug and Receptacle Holder for
MIL-DTL-38999, Series III MIL-DTL-38999 Series III H-17
–– –– –– 600HH005 Plug and Receptacle Holder for
MIL-DTL-38999, Series IV MIL-DTL-38999 Series IV H-18
–– –– –– 600J005 Plug and Receptacle Holder for
MIL-DTL-81511, Series I, II, III and IV MIL-DTL-81511
Series I, II, III & IV H-19
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Standard Materials, Finishes
and Tolerances
Note: Every effort has been made to present accurate
information in this catalog. Editorial errors that are
brought to our attention will be corrected in future editions.
All dimensions presented in this catalog should be
conrmed by the factory prior to inclusion within designs
or specications. We are constantly incorporating product
improvements and therefore Glenair reserves the right to
make changes without notice.
Any liability or warranty as to quality, performance, or
tness for use of Glenair products is always based on the
condition that they apply to only new , unused products that
are properly stored, handled, installed, used, maintained
and inspected by the user in a manner appropriate for the
intended use of the product.
On all length callouts, tolerance is ± .060 unless
otherwise specied.
Unless otherwise specied, the following other
dimensional tolerances will apply:
.xx = ± .030 (.080)
.xxx = ± .015 (0.400)
Lengths = ± .060 (1.524)
Angles = ± 5°
TOLERANCES
AS85049/GLENAIR FINISH CODE CROSS-REFERENCE
AS85049
Finish Code Material, Finish Recommended Glenair
Accessory Finish Code
AAluminum, Black Anodize (RoHS Compliant) C
BStainless Steel, Cadmium Plate, Black ZU
GAluminum, Electroless Nickel Plate (Space Grade) MA
JComposite, Cadmium Plate, Olive Drab XW
LComposite, Cadmium Plate, Olive Drab, Selective XX
MComposite, Electroless Nickel Plate (RoHS Compliant) XM
NAluminum, Electroless Nickel Plate M
PAluminum, Cadmium Plate, Olive Drab, Selective NFP
SStainless Steel, Pasivate (RoHS Compliant) Z1
TComposite, Unplated (RoHS Compliant) XO
WAluminum, Cadmium Plate, Olive Drab NF
XAluminum, Nickel Fluorocarbon Polymer (RoHS Compliant) MT
XC Composite, Nickel Fluorocarbon Polymer (RoHS Compliant) XMT
XS Stainless Steel, Nickel Fluorocarbon Polymer (RoHS Compliant) ZMT
YAluminum, Pure Dense Electrodeposited Aluminum (RoHS Compliant) AL
YC Composite, Pure Dense Electrodeposited Aluminum (RoHS Compliant) XAL
YL Composite, Pure Dense Electrodeposited Aluminum, Selective (RoHS Compliant) XAP
YP Aluminum, Pure Dense Electrodeposited Aluminum, Selective (RoHS Compliant) ALP
YS Stainless Steel, Pure Dense Electrodeposited Aluminum, Selective (RoHS Compliant) ZAL
ZAluminum, Zinc Nickel, Black (RoHS Compliant) ZR
ZC Composite, Zinc Nickel, Black (RoHS Compliant) XZR
ZL Composite, Zinc Nickel, Black, Selective (RoHS Compliant) XZS
ZP Aluminum, Zinc Nickel, Black, Selective (RoHS Compliant) ZS
ZS Stainless Steel, Zinc Nickel, Black (RoHS Compliant) ZZR
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-11
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Recommended Torque Values
INSTALLATION TORQUE VALUES FOR CIRCULAR ELECTRICAL CONNECTOR ACCESSORIES
Shell Sizes Group 1
Light and Medium Duty
AS50151 (AS31001 Series)
MIL-DTL-26482 Series I
MIL-DTL-26500
MIL-DTL-27599
MIL-DTL-38999 Series I and II
MIL-C-81511 Series I, II, III and IV
AS81703 Series I
Group 2
Heavy Duty
AS50151 (AS34001 Series)
MIL-DTL-22992
MIL-DTL-26482 Series II
MIL-DTL-28840
MIL-DTL-38999 Series III and IV
AS81703 Series III
MIL-DTL-83723 Series I, II and III
Group 2
Composite
Material
Coupling
Threads
(See Note 1)
Torque Requirements in Inch-Pounds
8, 9, A 30/40 51/61 35
3, 10, 10SL, 11, B 30/40 71/81 35
7, 12, 12S, 13, C 35/45 103/113 45
14, 14S, 15, D 35/45 111/121 45
16, 16S, 17, E 35/45 111/121 45
18, 19, 27, F 35/45 111/121 45
20, 21, 37, G 75/85 131/141 80
22, 23, H 75/85 131/141 80
24, 25, 61, J 75/85 131/141 80
28, 29 115/125 143/153 120
32, 33 115/125 143/153 120
36 115/125 142/153 120
40 155/165 159/169 N/A
44 155/165 159/169 N/A
48 155/165 159/169 N/A
TORQUE VALUES FOR CABLE CLAMP SCREWS
Torque requirements in Inch-Pounds for corrosion
resitant or steel plated screws only
Screw Size
Into Aluminum or Corrosion
Resistant Steel
2-56 1.5/2.5
4-40 3.5/4.5
6-32 5.0/7.0
8-32 7.0/9.0
10-32 9.0/11.0
.250-20 11.0/13.0
CABLE CLAMP WITH GROMMET - TORQUE VALUES
Torque Requirements in Inch-Pounds
Clamp Size Torque Min/Max Values
3 30/40
4 30/40
6 35/55
8 35/55
10 35/55
12 40/60
16 40/60
20 40/60
24 80/100
28 80/100
32 80/100
40 80/100
EMI/RFI shielding terminated with conical metal ferrule(s) should
employ a minimum recommended torque of 35 in-lb.
1) Use Glenair 600-091 and 600-007 Torque Tools when tightening
hexagonal composite accessory couplings.
2) For additional guidance or values/conditions not listed, refer to SAE
AIR6151.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-12
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
MILITARY STANDARD CONNECTOR INDEX
Part No. Connector
Designator AS50151
Specication Series Description
MS3100 B AS50151 AS31001 Receptacle, Wall Mtg (Solder)
MS3101 B AS50151 AS31001 Receptacle
MS3102 ** AS50151 AS31001 Receptacle, Box Mtg (Solder)
MS3103 ** AS50151 AS31001 Receptacle, Potting (Solder)
MS3105 ** AS50151 AS31001 Dummy Receptacle
MS3106 B AS50151 AS31001 Plug, Straight (Solder)
MS3107 B AS50151 AS31001 Plug, Quick Disconnect (Solder)
MS3108 B AS50151 AS31001 Plug, 90° (Solder)
MS3110 D-729 MIL-DTL-26482 1 Receptacle, Wall Mtg
MS3111 D MIL-DTL-26482 1 Plug, Cable Connecting
MS3112 ** MIL-DTL-26482 1 Receptacle, Box Mount
MS3113 ** MIL-DTL-26482 1 Receptacle, Solder Mtg
MS3114 D-717 MIL-DTL-26482 1 Receptacle, Jam Nut
MS3115 ** MIL-DTL-26482 1-2 Dummy Receptacle
MS3116 D MIL-DTL-26482 1 Plug, Straight
MS3119 ** MIL-DTL-26482 1 Receptacle, Thru-Bulkhead
MS3120 D MIL-DTL-26482 1 Receptacle, Wall Mtg (Crimp)
MS3121 D MIL-DTL-26482 1 Plug, Straight (Crimp)
MS3122 ** MIL-DTL-26482 1 Receptacle, Box Mtg (Crimp)
MS3124 D-717 MIL-DTL-26482 1 Receptacle, Reart Mtg, Jam Nut (Crimp)
MS3126 D MIL-DTL-26482 1 Plug, Straight (Crimp)
MS3127 ** MIL-DTL-26482 1 Receptacle, Box Mtg (Crimp)
MS3128 * MIL-DTL-26482 1 Plug, Straight (Crimp)
MS3130 * AS81703 1 Receptacle, Push Pull, Wide Flange
MS3132 X-706 AS81703 1 Receptacle, Push Pull, Box Mtg
MS3134 X-706 AS81703 1 Receptacle, Push Pull, Jam Nut
MS3135 ** AS81703 1 Dummy Receptacle
MS3137 X-706 AS81703 1 Plug, Straight, Push Pull
MS3138 X-706 AS81703 1 Plug, Lanyard, Push Pull
MS3139 ** AS81703 1 Receptackle, Thru-Bulkhead
MS3140 X-706B AS81703 2 Receptacle, Push Pull, Wall Mtg
MS3142 ** AS81703 AS31001 Receptacle, Hermetic, Box Mtg
MS3143 ** AS81703 AS31001 Receptacle, Hermetic, Solder Mount
MS3144 X-706B AS81703 2 Receptacle, Push Pull, Jam Nut
MS3145 ** AS81703 3 Receptacle, Hermetic, Push Pull, Box Mount
MS3146 ** AS81703 3 Receptacle, Push Pull, Hermetic, Solder Mount
MS3147 X-706B AS81703 2 Plug, Push Pull (Crimp)
MS3148 X706B AS81703 2 Plug, Push Pull, Lanyard (Crimp)
MS3149 ** AS81703 3 Receptacle, Push Pull, Hermetic
* Consult Factory
** Connector does not accommodate rear accessories.
The following is a list of circular connectors dened
by U.S. Military Specications, cross-referenced to
the applicable active or inactive part number series.
The symbols in the Connector Designator column
are an essential element in Glenair’s commercial
backshell part number developments.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-13
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
MS3400 A AS50151 AS34001 Receptacle, Wall Mtg
MS3401 A AS50151 AS34001 Receptacle, Cable Connecting
MS3402 ** AS50151 AS34001 Receptacle, Box Mtg
MS3404 A AS50151 AS34001 Receptacle, Jam Nut
MS3406 A AS50151 AS34001 Plug
MS3408 A AS50151 AS34001 Plug, 90°
MS3409 A AS50151 AS34001 Plug, 45°
MS3412 A AS50151 AS34001 Receptacle, Wall Mtg
MS3424 A AS81703 3 Receptacle, Push Pull, Wall Mtg
MS3440 ** MIL-DTL-26482 2 Receptacle, Narrow Flange Mtg (Was M83723/9/10)
MS3442 ** MIL-DTL-26482 2 Receptacle, Wide Flange Mtg
MS3443 ** MIL-DTL-26482 2 Receptacle, Solder Flange Mtg
MS3445 * AS81703 2 Plug, push Pull, Rack and Panel Mtg
MS3446 A AS81703 3 Plug, Rack and Panel
MS3449 ** MIL-DTL-26482 2 Receptacle, Single Hole Mtg
MS3450 A AS50151 AS34501 Receptacle, Wall Mtg (Was M83723/9/10)
MS3451 A AS50151 AS34501 Receptacle, Cable Connecting (Was M83723/19/20)
MS3452 ** AS50151 AS34501 Receptacle, Box Mtg (Was M83723/21/22)
MS3454 A AS50151 AS34501 Receptacle, Jam Nut
MS3456 A AS50151 AS34501 Plug, Straight (Was M83723/52/53)
MS3459 A AS50151 AS34501 Plug, Straight, Self-Locking (Was M83723/17/18)
MS3463 ** AS81703 3 Receptacle, Push Pull
MS3464 A AS81703 3 Receptacle, Push Pull, Jam Nut
MS3466 ** AS81703 3 Receptacle, Push Pull, Hermetic
MS3467 A AS81703 3 Plug, Push Pull
MS3468 A AS81703 3 Plug, Push Pull, Lanyard
MS3469 ** AS81703 3 Receptacle, Push Pull, Hermetic, Jam Nut
MS3470 A MIL-DTL-26482 2 Receptacle, Narrow Flange Mtg (Was M83723/1/2)
MS3471 A MIL-DTL-26482 2 Receptacle, Cable Connecting (Was M83723/7/8)
MS3472 A MIL-DTL-26482 2 Receptacle, Wide Flange Mtg (Was M83723/3/4))
MS3473 ** MIL-DTL-26482 2 Receptacle, Solder Mtg, Hermetic
MS3474 A MIL-DTL-26482 2 Receptacle, Rear Mtg, Jam Nut (Was M83723/5/6)
MS3475 A MIL-DTL-26482 2 Plug, RFI Shielded (Was M83723/42/43)
MS3476 A MIL-DTL-26482 2 Plug, Straight, (Was M83723/13/14)
MS3477 ** MIL-DTL-26482 2 Receptacle, Hermetic, Box Mtg
MS3479 ** MIL-DTL-26482 2 Receptacle, Hermetic, Rear Mtg, Jam Nut
MS17343 C MIL-DTL-22992 R Receptacle, Wall Mtg
MS17344 C MIL-DTL-22992 R Plug, Straight
MS17345 C MIL-DTL-22992 R Plug, Cable Connecting
MS17346 C MIL-DTL-22992 R Receptacle, Box Mtg
MS17347 C MIL-DTL-22992 R Receptacle, Jam Nut
MS17348 C MIL-DTL-22992 R Receptacle, Jam Nut, Box Mtg
MS18062 ** MIL-DTL-22992 R Dummy Receptacle
MS20026 * MIL-DTL-27599 Receptacle, Wall Mtg, Solder
MS20027 * MIL-DTL-27599 Receptacle, Line
MS20028 * MIL-DTL-27599 Plug, Straight
MS20029 ** MIL-DTL-27599 Receptacle, Jam Nut Mtg
* Consult Factory ** Connector does not accommodate rear accessories.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-14
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
MS20030 * MIL-DTL-27599 Receptacle, Box Mtg, Hermetic
MS20031 ** MIL-DTL-27599 Receptacle, Jam Nut, Hermetic
MS20032 ** MIL-DTL-27599 Receptacle, Solder Mtg, Hermetic
MS20034 * MIL-DTL-27599 Receptacle, Wall Mtg
MS20035 * MIL-DTL-27599 Receptacle, Box Mtg
MS24264 E MIL-DTL-26500 F, G & R Receptacle, Flange Mtg
MS24265 E MIL-DTL-26500 F, G & R Receptacle, Single Hole Mtg
MS24266 E MIL-DTL-26500 F, G & R Plug, Straight
MS25183 ** AS50151 AMS31001 Plug, Potting Seal
MS27034 ** MIL-DTL-26500 Receptacle, Hermetic, Solder Mtg
MS27334 * MIL-DTL-27599 Receptacle, Wall Mtg
MS27335 ** MIL-DTL-27599 Receptacle, Box Mtg
MS27336 * MIL-DTL-27599 Plug, Straight
MS27337 * MIL-DTL-27599 Receptacle, Jam Nut
MS27338 * MIL-DTL-27599 Receptacle, Wall Mtg, Hermetic
MS27339 ** MIL-DTL-27599 Receptacle, Box Mtg, Hermetic
MS27340 ** MIL-DTL-27599 Receptacle, Jam Nut Mtg, Hermetic
MS27341 ** MIL-DTL-27599 Receptacle, Solder Mtg, Hermetic
MS27466 F MIL-DTL-38999 I Receptacle, Wall Mtg
MS27467 F MIL-DTL-38999 I Plug, Straight
MS27468 F MIL-DTL-38999 I Receptacle, Jam Nut
MS27469 ** MIL-DTL-38999 I Receptacle, Wall Mtg, Hermetic
MS27470 ** MIL-DTL-38999 I Receptacle, Jam Nut, Hermetic
MS27471 ** MIL-DTL-38999 I Receptacle, Solder Mtg, Hermetic
MS27472 F MIL-DTL-38999 II Receptacle, Wall Mtg
MS27473 F MIL-DTL-38999 II Plug, Straight
MS27474 F MIL-DTL-38999 II Receptacle, Jam Nut
MS27475 F MIL-DTL-38999 II Receptacle, Wall Mtg
MS27476 ** MIL-DTL-38999 II Receptacle, Box Mtg, Hermetic
MS27477 ** MIL-DTL-38999 II Receptacle, Jam Nut, Hermetic
MS27478 ** MIL-DTL-38999 II Receptacle, Solder Mtg, Hermetic
MS27479 F MIL-DTL-38999 II Inactive Use MS27472
MS27480 F MIL-DTL-38999 II Inactive Use MS27473
MS27481 F MIL-DTL-38999 II Inactive Use MS27474
MS27482 F MIL-DTL-38999 II Inactive Use MS27475
MS27483 ** MIL-DTL-38999 II Inactive Use MS27477
MS27484P ** MIL-DTL-38999 II Plug, Straight
MS27484T F MIL-DTL-38999 II Plug, Straight
MS27496 ** MIL-DTL-38999 I Receptacle, Box Mtg
MS27497 F MIL-DTL-38999 II Receptacle, Back Panel Wall Mtg
MS27498 F MIL-DTL-38999 I Plug, 90°
MS27499 ** MIL-DTL-38999 II Receptacle, Box Mtg
MS27500 F MIL-DTL-38999 II Inactive See MS27473
MS27503 ** MIL-DTL-38999 II Inactive See MS27478
MS27504 ** MIL-DTL-38999 II Inactive See MS27499
M81511/23 J AS81511 1 Receptacle, Jam Nut
M81511/24 ** AS-81511 1 Receptacle, Jam Nut
* Consult Factory ** Connector does not accommodate rear accessories.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-15
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
MS27505 ** MIL-DTL-38999 I Receptacle, Back Panel Box Mtg
MS27508 ** MIL-DTL-38999 II Receptacle, Back Panel Box Mtg
MS27513 ** MIL-DTL-38999 II Receptacle, Box Mtg
MS27515 F MIL-DTL-38999 I Inactive Use MS27656
MS27613 E-710 MIL-DTL-26500K Receptacle, Panel Mtg
MS27614 E-710 MIL-DTL-26500K Receptacle, D-Hole Mtg
MS27615 E-710 MIL-DTL-26500K Plug, Straight
MS27652 F MIL-DTL-38999 I Inactive Use MS27466
MS27653 F MIL-DTL-38999 I Inactive Use MS27467
MS27654 F MIL-DTL-38999 I Inactive Use MS27656
MS27656 F MIL-DTL-38999 I Receptacle, Back Panel, Wall Mtg
MS27661 F-752 MIL-DTL-38999 I Plug, Lanyard Release
MS27662 ** MIL-DTL-38999 I Receptacle, Thru-Bulkhead
MS27664 ** MIL-DTL-38999 II Receptacle, Back-Panel Wall Mtg
MS27665 F MIL-DTL-38999 I Plug, Rack & Panel Mtg
MS27667 ** MIL-DTL-38999 II Receptacle, Thru-Bulkhead
MS90555 * MIL-DTL-22992 L Receptacle, Wall Mtg
MS90556 * MIL-DTL-22992 L Plug, Straight
MS90557 * MIL-DTL-22992 L Plug, Cable Connecting
MS90558 * MIL-DTL-22992 L Receptacle, W/Coupling Ring, Wall Mtg
M28840/10 G MIL-DTL-28840 Receptacle, Wall Mtg
M28840/11 G MIL-DTL-28840 Receptacle, Cable Connecting
M28840/12 ** MIL-DTL-28840 Receptacle, Box Mtg
M28840/14 G MIL-DTL-28840 Receptacle, Jam Nut
M28840/16 G MIL-DTL-28840 Plug, Straight
D38999/20 H MIL-DTL-38999 III Receptacle, Wall Mtg
D38999/21 ** MIL-DTL-38999 III Receptacle, Hermetic
D38999/23 ** MIL-DTL-38999 III Receptacle, Hermetic, Jam Nut
D38999/24 H MIL-DTL-38999 III Receptacle, Jam Nut
D38999/25 ** MIL-DTL-38999 III Receptacle, Hermetic, Solder Mtg
D38999/26 H MIL-DTL-38999 III Plug, Straight
D38999/27 ** MIL-DTL-38999 III Receptacle, Hermetic, Weld Mtg
D38999/29 * MIL-DTL-38999 III Plug, Lanyard Release
D38999/30 H-701 MIL-DTL-38999 III Plug, Lanyard Release
D38999/40 H MIL-DTL-38999 IV Receptacle, Wall Mtg
D38999/42 H MIL-DTL-38999 IV Receptacle, Box Mtg
D38999/44 H-715 MIL-DTL-38999 IV Receptacle, Jam Nut
D38999/46 H MIL-DTL-38999 IV Plug, Straight, EMI
D38999/47 H MIL-DTL-38999 IV Plug, Straight
M81511/1 J AS81511 2 Receptacle, Flange Mtg
M81511/2 ** AS81511 2 Receptacle, Solder Flange
M81511/3 J AS81511 2 Receptacle, Jam Nut
M81511/4 ** AS81511 2 Receptacle, Jam Nut
M81511/5 J AS81511 2 Plug, Cable Connecting
M81511/6 J AS81511 2 Plug
M81511/21 J AS81511 1 Receptacle, Flange Mtg
M81511/22 ** AS81511 1 Receptacle, Solder Flange Mtg
* Consult Factory ** Connector does not accommodate rear accessories.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-16
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
M81511/23 J AS81511 1 Receptacle, Jam Nut
M81511/24 ** AS81511 1 Receptacle, Jam Nut
M81511/25 J AS81511 1 Receptacle, Cable Connecting
M81511/26 J AS81511 1 Plug
M81511/27 ** AS81511 1 Receptacle Thru-Bulkhead, Jam Nut
M81511/28 ** AS81511 2 Receptacle, Thru-Bulkhead, Single Hole Mtg
M81511/31 J AS81511 2 Receptacle, Flange Mtg
M81511/32 J AS81511 2 Receptacle, Jam Nut Mtg
M81511/33 J AS81511 2 Recepacle,Cable Connecting
M81511/34 J AS81511 2 Plug
M81511/35 J AS81511 1 Receptacle, Flange Mtg
M81511/36 J AS81511 1 Receptacle, Jam Nut
M81511/37 J AS81511 1 Receptacle, Cable Connecting
M81511/38 J AS81511 1 Plug
M81511/41 J AS81511 3 Receptacle, Flange Mtg
M81511/42 ** AS81511 3 Receptacle, Solder Flange Mtg
M81511/44 ** AS81511 3 Receptacle, Jam Nut
M81511/45 J AS81511 3 Receptacle, Cable Connecting
M81511/46 J AS81511 3 Plug
M81511/47 ** AS81511 3 Receptacle, Solder Flange Mtg
M81511/48 ** AS81511 3 Receptacle, Jam Nut
M81511/49 J AS81511 3 Receptacle, Jam Nut
M81511/50 ** AS81511 4 Receptacle, Jam Nut
M81511/51 J AS81511 4 Receptacle, Flange Mtg
M81511/52 ** AS81511 4 Receptacle, Solder Flange Mtg
M81511/53 J AS81511 4 Receptacle, Jam Nut
M81511/54 ** AS81511 4 Receptacle, Jam Nut
M81511/55 J AS81511 4 Receptacle, Cable Connecting
M81511/56 J AS81511 4 Plug
M81511/57 ** AS81511 4 Receptacle, Solder Flange Mtg
M81582/1 * MIL-C-81582 Receptacle, Single Hole Mtg
M81582/2 * MIL-C-81582 Plug, Lanyard Release
M83723/1 A MIL-DTL-83723 I Superseded by MS3470
M83723/2 A MIL-DTL-83723 I Superseded by MS3470
M83723/3 A MIL-DTL-83723 I Superseded by MS3472
M83723/4 A MIL-DTL-83723 I Superseded by MS3472
M83723/5 A MIL-DTL-83723 I Superseded by MS3474
M83723/6 A MIL-DTL-83723 I Superseded by MS3474
M83723/7 A MIL-DTL-83723 I Superseded by MS3471
M83723/8 A MIL-DTL-83723 I Superseded by MS3471
M83723/9 ** MIL-DTL-83723 I Superseded by MS3440
M83723/10 ** MIL-DTL-83723 I Superseded by MS3442
M83723/11 ** MIL-DTL-83723 I Superseded by MS3443
M83723/12 ** MIL-DTL-83723 I Superseded by MS3443
M83723/13 A MIL-DTL-83723 I Superseded by MS3476
M83723/14 A MIL-DTL-83723 I Superseded by MS3476
M83723/17 K MIL-DTL-83723 II Superseded by MS3451
* Consult Factory ** Connector does not accommodate rear accessories.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-17
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
MS27505 ** MIL-DTL-38999 I Receptacle, Back Panel Box Mtg
MS27508 ** MIL-DTL-38999 II Receptacle, Back Panel Box Mtg
MS27513 ** MIL-DTL-38999 II Receptacle, Box Mtg
MS27515 F MIL-DTL-38999 I Inactive Use MS27656
MS27613 E-710 MIL-DTL-26500K Receptacle, Panel Mtg
MS27614 E-710 MIL-DTL-26500K Receptacle, D-Hole Mtg
MS27615 E-710 MIL-DTL-26500K Plug, Straight
MS27652 F MIL-DTL-38999 I Inactive Use MS27466
MS27653 F MIL-DTL-38999 I Inactive Use MS27467
MS27654 F MIL-DTL-38999 I Inactive Use MS27656
MS27656 F MIL-DTL-38999 I Receptacle, Back Panel, Wall Mtg
MS27661 F-752 MIL-DTL-38999 I Plug, Lanyard Release
MS27662 ** MIL-DTL-38999 I Receptacle, Thru-Bulkhead
MS27664 ** MIL-DTL-38999 II Receptacle, Back-Panel Wall Mtg
MS27665 F MIL-DTL-38999 I Plug, Rack & Panel Mtg
MS27667 ** MIL-DTL-38999 II Receptacle, Thru-Bulkhead
MS90555 * MIL-DTL-22992 L Receptacle, Wall Mtg
MS90556 * MIL-DTL-22992 L Plug, Straight
MS90557 * MIL-DTL-22992 L Plug, Cable Connecting
MS90558 * MIL-DTL-22992 L Receptacle, W/Coupling Ring, Wall Mtg
M28840/10 G MIL-DTL-28840 Receptacle, Wall Mtg
M28840/11 G MIL-DTL-28840 Receptacle, Cable Connecting
M28840/12 ** MIL-DTL-28840 Receptacle, Box Mtg
M28840/14 G MIL-DTL-28840 Receptacle, Jam Nut
M28840/16 G MIL-DTL-28840 Plug, Straight
D38999/20 H MIL-DTL-38999 III Receptacle, Wall Mtg
D38999/21 ** MIL-DTL-38999 III Receptacle, Hermetic
D38999/23 ** MIL-DTL-38999 III Receptacle, Hermetic, Jam Nut
D38999/24 H MIL-DTL-38999 III Receptacle, Jam Nut
D38999/25 ** MIL-DTL-38999 III Receptacle, Hermetic, Solder Mtg
D38999/26 H MIL-DTL-38999 III Plug, Straight
D38999/27 ** MIL-DTL-38999 III Receptacle, Hermetic, Weld Mtg
D38999/29 * MIL-DTL-38999 III Plug, Lanyard Release
D38999/30 H-701 MIL-DTL-38999 III Plug, Lanyard Release
D38999/40 H MIL-DTL-38999 IV Receptacle, Wall Mtg
D38999/42 H MIL-DTL-38999 IV Receptacle, Box Mtg
D38999/44 H-715 MIL-DTL-38999 IV Receptacle, Jam Nut
D38999/46 H MIL-DTL-38999 IV Plug, Straight, EMI
D38999/47 H MIL-DTL-38999 IV Plug, Straight
M81511/1 J AS81511 2 Receptacle, Flange Mtg
M81511/2 ** AS81511 2 Receptacle, Solder Flange
M81511/3 J AS81511 2 Receptacle, Jam Nut
M81511/4 ** AS81511 2 Receptacle, Jam Nut
M81511/5 J AS81511 2 Plug, Cable Connecting
M81511/6 J AS81511 2 Plug
M81511/21 J AS81511 1 Receptacle, Flange Mtg
M81511/22 ** AS81511 1 Receptacle, Solder Flange Mtg
* Consult Factory ** Connector does not accommodate rear accessories.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
A-18
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
INDEX AND
INTRODUCTION
A
Military Standard Connector Index
and Reference Guide
Part No. Connector
Designator Specication Series Description
M83723/94 ** MIL-DTL-83723 III Receptacle, Bayonet, Single Hole Mtg., Hermetic
M83723/95 A MIL-DTL-83723 III Plug, Threaded, Socket Contact, Self-Locking
M83723/96 A MIL-DTL-83723 III Plug, Threaded, Pin Contact, Self-Locking
M83723/97 A MIL-DTL-83723 III Plug, Threaded, RFI, Socket Contact, Self-Locking
M83723/98 A MIL-DTL-83723 III Plug, Threaded, Pin Contact, Self-Locking
NATC00 H* SSQ221635 Receptacle, Flange
NATC06 H* SSQ221635 Plug
NATC07 H* SSQ221635 Receptacle, Jam Nut
NATC09 *** SSQ221635 Receptacle, Weld Mtg.
NATC77 *** SSQ221635 Receptacle, Jam Nut
NATC99 *** SSQ221635 Receptacle, Weld Mtg.
NBO A 40M39569 Receptacle, Flange Mtg.
NBOH ** 40M39569 Receptacle, Hermetic
NB3H ** 40M39569 Receptacle, Hermetic
NB4 A 40M39569 Receptacle, Flange Mtg.
NB5H ** 40M39569 Through-Bulkhead, Hermetic
NB6 A 40M39569 Plug, Straight
NB6G A 40M39569 Plug, Straight, EMI
NB7 A 40M39569 Receptacle, Jam Nut
NB7H ** 40M39569 Receptacle, Hermetic
NB8H ** 40M39569 Receptacle, Hermetic
NLSO F 40M38277 Receptacle, Flange Mtg.
NLS3H ** 40M38277 Receptacle, Hermetic
NLS6 F 40M38277 Plug, Straight
NLS6G F 40M38277 Plug, Straight, EMI
NLS7 F 40M38277 Receptacle, Jam Nut
NLS7H ** 40M38277 Receptacle, Jam Nut
NZGL00 H** SSQ21635 Receptacle, Flange
NZGL03 *** SSQ21635 Receptacle, Lever
NZGL06 H** SSQ21635 Plug
NZGL07 H** SSQ21635 Receptacle, Weld Mtg
NZGL09 *** SSQ21635 Receptacle, Weld Mtg
NZGL66 H** SSQ21635 Plug
NZGL77 *** SSQ21635 Receptacle, Jam Nut
NZGL99 *** SSQ21635 Receptacle, Weld Mtg
* Consult Factory
** Connector does not accommodate rear accessories.
H* NATC Series size 09 through 25 mates to Glenair connector designator H. Consult factory for sizes 33 and 37.
H** NZGL Series requires special accessories manufactured by Glenair. Consult factory.
*** Connector noted does not have accessory thread (NZGL and NATC hermetic/control leakage classes).
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049
Qualied Backshells and Connector Accessories
Part No. Description
Page
No.
AS85049/1 Straight Strain Relief B-2
AS85049/2 Straight Environmental Strain Relief B-3
AS85049/3 Straight Environmental Backshell B-4–6
AS85049/4 Straight Step-Up Environmental Backshell B-7–11
AS85049/5 Straight Step-Down Environmental Backshell B-13–17
AS85049/6 45° RFI/EMI Environmental Backshell B-19
AS85049/7 45° Environmental Backshell B-21
AS85049/8 90° RFI/EMI Environmental Backshell B-23
AS85049/9 90° Environmental Backshell B-25
AS85049/10 Straight RFI/EMI Environmental Backshell B-27
AS85049/11 Straight Environmental Backshell B-31
AS85049/14 E Nuts B-35
AS85049/15 45° Qwik-Ty® Strain Reliefs B-36
AS85049/16 90° Qwik-Ty® Strain Reliefs B-36
AS85049/17 Straight RFI/EMI Environmental Backshell B-37
AS85049/18 Straight RFI/EMI Environmental Backshell B-38
AS85049/19 Straight Environmental Backshell B-39
AS85049/20 Straight Crimp Ring Backshell and Crimp Ring B-41
AS85049/21 Straight Non-Environmental Strain Relief B-42
AS85049/23 45° RFI-EMI Non-Environmental Backshell B-43
AS85049/24 90° RFI-EMI Non-Environmental Backshell B-45
AS85049/25 Straight RFI-EMI Non-Environmental Backshell B-47
AS85049/26 Adapter / Crimp Ring B-51–52
AS85049/27 E Nuts B-53
AS85049/28 Strt. Rectangular Non-Environmental Backshell B-54
AS85049/29 Straight Non-Environmental Strain Relief B-55
AS85049/30 Straight RFI-EMI Shield Termination Backshell B-56
AS85049/31 E Nuts B-57
AS85049/33 Straight Crimp Ring Non-Env. Backshell B-58
AS85049/34 Straight Adapter and Extender B-59
AS85049/36 Straight RFI-EMI Non-Environmental Backshell B-60
AS85049/37 90° RFI-EMI Non-Environmental Backshell B-61
AS85049/38 Straight Strain Reliefs B-62
AS85049/39 90° Strain Reliefs B-63
AS85049/41 Straight Strain Relief B-64
AS85049/42 Straight Strain Relief B-65
AS85049/43 45° Strain Relief B-66
AS85049/44 Straight Rectangular Strain Relief Backshell B-67
AS85049/45 Straight Strain Relief B-68
AS85049/46 90° Non-Self-Locking Composite Strain Relief B-69
AS85049/47 90° Strain Reliefs B-70
AS85049/48 Rectangular Strain Relief Backshell B-71–73
AS85049/49 Straight Strain Relief B-74
AS85049/50 Rectangular Strain Relief Backshell B-75
AS85049/51 90° Strain Reliefs B-76
AS85049/52 Straight Strain Reliefs B-77
Part No. Description
Page
No.
AS85049/53 /54 /55 Qwik-Ty® Strain Reliefs B-78
AS85049/56 /57 Qwik-Ty® Strain Reliefs B-79
AS85049/58 Potting Boot Ring B-80
AS85049/59 Straight Shrink Boot Adapter B-81
AS85049/60 Straight Shrink Boot Adapters B-82–83
AS85049/61 Potting Boot Ring B-84
AS85049/62 Straight Shrink Boot Adapter B-85
AS85049/63 90° Qwik-Ty® Strain Relief B-86
AS85049/69 Straight Shrink Boot Adapter B-87
AS85049/74 Potting Boot B-88
AS85049/75 Potting Boot B-89
AS85049/76 90° EMI/RFI Environmental Backshell B-90
AS85049/77 45° EMI/RFI Environmental Backshell B-91
AS85049/78 45° EMI/RFI Environmental Backshell B-92
AS85049/79 90° EMI/RFI Environmental Backshell B-93
AS85049/80 Sealing Plug, Sizes 8, 12 and 16 B-94
AS85049/81 Sealing Plug B-96
AS85049/82 /83 /84 Banding Backshells B-97
AS85049/85 /86 /87 Banding Backshells B-99
AS85049/88 /89 /90 Banding Backshells B-101
AS85049/91 /92 Strain Reliefs B-103
AS85049/93 Banding Split Ring B-104
AS85049/94 Full Perimeter Mounting Flange B-105
AS85049/95 3/4 Perimeter Mounting Flange B-106
AS85049/96 1/4 Perimeter Mounting Flange B-107
AS85049/103 Straight Shield Sock Composite Adapter B-108
AS85049/104 45° Shield Sock Composite Adapter B-110
AS85049/105 90° Shield Sock Composite Adapter B-112
AS85049/109 Straight Shield Sock Shrink Boot Adapter B-114
AS85049/111 90° Shield Sock Sock Shrink Boot Adapter B-116
AS85049/112 Straight Shield Sock Sock Shrink Boot Adapter B-118
AS85049/114 90° Shield Sock Shrink Boot Adapter B-120
AS85049/115 Straight Shield Sock Shrink Boot Adapter B-122
AS85049/118 Straight Strain Relief B-124
AS85049/120 90° Strain Relief B-126
AS85049/121 Straight Strain Relief B-128
AS85049/123 90° Strain Relief B-130
AS85049/124 Sraight Strain Relief B-132
AS85049/126 90° Strain Relief B-134
AS85049/127 Bushing Strip B-136
AS85049/128-3, -4 Clamping Bands B-137
AS85049/130 Gasket B-138
AS85049/139 Telescoping Bushing, C or L B-140
AS85049/140 Straight Lipped Heat Shrink Boots B-142–148
AS85049/141 90° Lipped Heat Shrink Boots B-150–154
AS85049/142 Wide Body Heat Shrink Boot Transitions B-156–160
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/1 and MS3057B
Strain Reliefs
E Thread
F
G
H
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. Conn. Shell
Ref.(s) E Thread
Class 2B F
Max Ø G
Max H
Min
3B 8S, 10S 1/2 - 28 UNEF 1.031 (26.2) .812 (20.6) .231 (5.9)
4B 10SL, 12S, 12 5/8 - 24 UNEF 1.031 (26.2) .937 (23.8) .315 (8.0)
6B 14S, 14 3/4 - 20 UNEF 1.031 (26.2) 1.062 (27.0) .440 (11.2)
8B 16S, 16 7/8 - 20 UNEF 1.031 (26.2) 1.188 (30.2) .515 (13.1)
10B 18 1 - 20 UNEF 1.094 (27.8) 1.312 (33.3) .614 (15.6)
12B 20, 22 1 3/16 - 18 UNEF 1.219 (31.0) 1.562 (39.7) .738 (18.7)
16B 24, 28 1 7/16 - 18 UNEF 1.219 (31.0) 1.750 (44.5) .926 (23.5)
20B 32 1 3/4 - 18 UNS 1.344 (34.1) 2.250 (57.2) 1.200 (30.5)
24B 36 2 - 18 UNS 1.547 (39.3) 2.375 (60.3) 1.363 (34.6)
28B 40 2 1/4 - 16 UN 1.547 (39.3) 2.625 (66.7) 1.611 (40.9)
32B 44 2 1/2 - 16 UN 1.734 (44.0) 2.812 (71.4) 1.865 (47.4)
40B 48 3 - 16 UN 1.781 (45.2) 3.312 (84.1) 2.365 (60.1)
Basic
Part Number
M85049/1 -12B
Dash No. Superseded
Part Number
MS3057-16B
Basic
Part No. Dash
No.
APPLICATION NOTES
1. Finish on M85049/1 is Cadmium Olive Drab over Electroless Nickel (1,000 hour salt spray.
2. Assembly to be identied with manufacturer’s name and part number, space permitting.
3. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
4. For complete dimensions, see the applicable Military Specication.
5. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/2 and MS3057C
Strain Reliefs
E Thread
Cable
Entry
F
G
Clamping
Bars H (See
Note 3)
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. Conn. Shell
Ref.(s) E Thread
Class 2B F
Max Ø G
Max H Max
Closed Cable Entry
Max
3C 8S, 10S 1/2 - 28 UNEF 1.375 (34.9) .812 (20.6) .217 (5.5) .219 (5.6)
4C 10SL, 12S, 12 5/8 - 24 UNEF 1.375 (34.9) .937 (23.8) .296 (7.5) .312 (7.9)
6C 14S, 14 3/4 - 20 UNEF 1.375 (34.9) 1.062 (27.0) .390 (9.9) .438 (11.1)
8C 16S, 16 7/8 - 20 UNEF 1.375 (34.9) 1.188 (30.2) .434 (11.0) .531 (13.5)
10C 18 1 - 20 UNEF 1.437 (36.5) 1.312 (33.3) .434 (11.0) .625 (15.9)
12C 20, 22 1 3/16 - 18 UNEF 1.437 (36.5) 1.562 (39.7) .596 (15.1) .750 (19.1)
16C 24, 28 1 7/16 - 18 UNEF 1.562 (39.7) 1.750 (44.5) .596 (15.1) .938 (23.8)
20C 32 1 3/4 - 18 UNS 1.812 (46.0) 2.250 (57.2) .858 (21.8) 1.250 (31.8)
24C 36 2 - 18 UNS 2.062 (52.4) 2.375 (60.3) .858 (21.8) 1.375 (34.9)
28C 40 2 1/4 - 16 UN 2.062 (52.4) 2.625 (66.7) 1.107 (28.1) 1.625 (41.3)
32C 44 2 1/2 - 16 UN 2.188 (55.6) 2.812 (71.4) 1.421 (36.1) 1.875 (47.6)
Basic
Part Number
M85049/2 -12C
Dash No.
Basic
Part No. Dash
No.
Superseded
Part Number
MS3057-16C
APPLICATION NOTES
1. Finish on M85049/2 is Cadmium Olive Drab over Electroless Nickel, 1,000 hour salt spray.
2. Assembly to be identied with manufacturer’s name and part number, space permitting.
3. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
4. For complete dimensions, see the applicable Military Specication.
5. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/3 Style 1
Straight Environmental Backshell
TABLE II: Cable Range
Dash
No. Shell
Size Cable Range
Min Max
1 12 .281 (7.1) .375 (9.5)
2 12 .188 (4.8) .281 (7.1)
3 14 .344 (8.7) .438 (11.1)
4 16 .511 (13.0) .605 (15.4)
5 16 .436 (11.1) .530 (13.5)
6 16 .311 (7.9) .405 (10.3)
7 18 .531 (13.5) .625 (15.9)
8 18 .605 (15.4) .699 (17.8)
9 18 .406 (10.3) .500 (12.7)
10 18 .361 (9.2) .455 (11.6)
11 20 .715 (18.2) .828 (21.0)
12 20 .449 (11.4) .562 (14.3)
13 22 .637 (16.2) .750 (19.1)
14 22 .787 (20.0) .900 (22.9)
15 22 .692 (17.6) .805 (20.4)
16 24 .930 (23.6) 1.055 (26.8)
17 24 .675 (17.1) 1.000 (25.4)
18 24 .984 (25.0) 1.109 (28.2)
19 24 .755 (19.2) .880 (22.4)
20 28 1.055 (26.8) 1.180 (30.0)
21 28 1.105 (28.1) 1.230 (31.2)
22 28 1.185 (30.1) 1.310 (33.3)
23 32 1.320 (33.5) 1.455 (37.0)
24 32 1.406 (35.7) 1.531 (38.9)
25 32 1.250 (31.8) 1.375 (34.9)
26 36 1.531 (38.9) 1.656 (42.1)
27 36 1.437 (36.5) 1.562 (39.7)
28 44 2.105 (53.5) 2.250 (57.2)
29 44 2.025 (51.4) 2.170 (55.1)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
TABLE I : Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) E
Max G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 3.365 (85.5) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 3.678 (93.4) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
16 1.0000 - 20 UNEF 1.183 (30.0) 4.177 (106.1) 1.344 (34.1) .980 (24.9) 1.125-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 4.489 (114.0) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 4.615 (117.2) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 4.647 (118.0) 1.608 (40.8) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 4.896 (124.4) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 4.959 (126.0) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 5.021 (127.5) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 5.083 (129.1) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
44 2.8750 - 16 UN 3.120 (79.2) 6.471 (164.4) 2.969 (75.4) .980 (24.9) 3.000-0.1P-0.2L-DS
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/3 W 10 A 1
Dash Number
(Table II) Type
A or BStyle 1
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/3 Style 2
Straight Environmental Backshell
TABLE II: Dash No. and Cable Range
Dash
No. Shell
Size Cable Range
Min Max
1 12 .246 (6.2) .396 (10.1)
2 14 .321 (8.2) .521 (13.2)
3 16 .446 (11.3) .646 (16.4)
4 18 .565 (14.4) .765 (19.4)
5 20 .690 (17.5) .890 (22.6)
6 22 .815 (20.7) 1.015 (25.8)
7 24 .980 (24.9) 1.180 (30.0)
8 28 1.230 (31.2) 1.430 (36.3)
9 28 1.030 (26.2) 1.230 (31.2)
10 32 1.430 (36.3) 1.670 (42.4)
11 36 1.660 (42.2) 1.860 (47.2)
12 40 1.860 (47.2) 2.110 (53.6)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/3 W 10 A 2
Dash Number
(Table II) Type
A or BStyle 2
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) E
Max G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 4.000 (101.6) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 4.100 (104.1) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
16 1.0000 - 20 UNEF 1.183 (30.0) 4.400 (111.8) 1.344 (34.1) .980 (24.9) 1.125-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 4.900 (124.5) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 4.900 (124.5) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 4.900 (124.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 5.000 (127.0) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 5.300 (134.6) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 5.600 (142.2) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 5.600 (142.2) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870 (72.9) 5.725 (145.4) 2.969 (75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/3 Style 3
Straight Environmental Backshell
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Size Cable Range
Min Max F Appr .
Free Length
1 12 .281 (7.1) .377 (9.6) 3.344 (84.9)
2 12 .219 (5.6) .281 (7.1) 1.062 (27.0)
3 14 .400 (10.2) .438 (11.1) 4.344 (110.3)
4 16 .511 (13.0) .605 (15.4) 5.188 (131.8)
5 16 .436 (11.1) .530 (13.5) 4.688 (119.1)
6 16 .316 (8.0) .405 (10.3) 3.688 (93.7)
7 18 .605 (15.4) .699 (17.8) 6.188 (157.2)
8 18 .560 (14.2) .625 (15.9) 6.188 (157.2)
9 18 .361 (9.2) .455 (11.6) 4.188 (106.4)
10 20 .715 (18.2) .828 (21.0) 6.688 (169.9)
11 20 .449 (11.4) .562 (14.3) 5.188 (131.8)
12 22 .787 (20.0) .900 (22.9) 7.188 (182.6)
13 22 .637 (16.2) .750 (19.1) 6.688 (169.9)
14 24 .984 (25.0) 1.109 (28.2) 7.688 (195.3)
15 24 .875 (22.2) 1.000 (25.4) 7.188 (182.6)
16 24 .755 (19.2) .880 (22.4) 6.688 (169.9)
17 28 1.185 (30.1) 1.310 (33.3) 8.688 (220.7)
18 28 1.105 (28.1) 1.230 (31.2) 8.188 (208.0)
19 28 1.055 (26.8) 1.180 (30.0) 8.188 (208.0)
20 32 1.406 (35.7) 1.531 (38.9) 10.688 (271.5)
21 32 1.320 (33.5) 1.455 (37.0) 9.688 (246.1)
22 32 1.250 (31.8) 1.375 (34.9) 9.688 (246.1)
23 36 1.531 (38.9) 1.656 (42.1) 12.688 (322.3)
24 36 1.437 (36.5) 1.562 (39.7) 11.188 (284.2)
25 44 2.105 (53.5) 2.250 (57.2) 17.188 (436.6)
26 44 2.025 (51.4) 2.170 (55.1) 17.188 (436.6)
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) E
Max G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 2.935 (74.5) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 3.248 (82.5) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
16 1.0000 - 20 UNEF 1.183 (30.0) 3.712 (94.3) 1.344 (34.1) .980 (24.9) 1.125-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 4.024 (102.2) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 4.115 (104.5) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 4.150 (105.4) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 4.212 (107.0) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 4.275 (108.6) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 4.337 (110.2) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 4.399 (111.7) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
44 2.8750 - 16 UN 3.120 (72.9) 5.799 (147.3) 3.217 (81.7) .980 (24.9) 3.000-0.1P-0.2L-DS
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/3 W 10 A 3
Dash Number
(Table II) Type
A or BStyle 3
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/4 Style 1
Straight Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range for the wire bundle or
cable. Dimensions shown are not intended for inspection criteria.
4. Approximate chain lengths: Dash No. 01-12 = 5.0 (127.0); Dash No. 13-29 =
6.0 (152.4).
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/4 W 10 A 1
Dash Number
(Table II) Type
A or BStyle 1
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-8
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/4 Style 1
Straight Environmental Backshell
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870(72.9) 2.969(75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
44 2.8750 - 16 UN 3.120 (79.2) 3.217 (81.7) .980 (24.9) 3.000-0.1P-0.2L-DS
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Size E
Max F
± .031 (0.8) Cable Range
Min Max
1 12 4.275 (108.6) 1.375 (34.9) .436 (11.1) .530 (13.5)
2 12 3.678 (93.4) 1.125 (28.6) .406 (10.3) .500 (12.7)
3 12 4.275 (108.6) 1.375 (34.9) .311 (7.9) .405 (10.3)
4 14 4.177 (106.1) 1.375 (34.9) .511 (13.0) .605 (15.4)
5 14 4.489 (114.0) 1.562 (39.7) .531 (13.5) .625 (15.9)
6 14 4.177 (106.1) 1.375 (34.9) .436 (11.1) .530 (13.5)
7 14 4.177 (106.1) 1.375 (34.9) .311 (7.9) .405 (10.3)
8 18 4.584 (116.4) 1.688 (42.9) .715 (18.2) .828 (21.0)
9 20 4.647 (118.0) 1.812 (46.0) .637 (16.2) .750 (19.1)
10 20 4.896 (124.4) 2.125 (54.0) .875 (22.2) 1.000 (25.4)
11 20 4.647 (118.0) 1.812 (46.0) .787 (20.0) .900 (22.9)
12 20 4.896 (124.4) 2.125 (54.0) .930 (23.6) 1.055 (26.8)
13 22 4.896 (124.4) 2.125 (54.0) .875 (22.2) 1.000 (25.4)
14 22 4.896 (124.4) 2.125 (54.0) .984 (25.0) 1.109 (28.2)
15 24 4.959 (126.0) 2.469 (62.7) 1.055 (26.8) 1.180 (30.0)
16 24 4.959 (126.0) 2.469 (62.7) 1.185 (30.1) 1.310 (33.3)
17 24 4.959 (126.0) 2.469 (62.7) 1.105 (28.1) 1.230 (31.2)
18 24 4.959 (126.0) 2.625 (66.7) 1.250 (31.8) 1.375 (34.9)
19 28 5.021 (127.5) 2.625 (66.7) 1.320 (33.5) 1.445 (36.7)
20 28 5.021 (127.5) 2.625 (66.7) 1.406 (35.7) 1.531 (38.9)
21 28 5.021 (127.5) 2.625 (66.7) 1.250 (31.8) 1.375 (34.9)
22 32 5.083 (129.1) 2.953 (75.0) 1.531 (38.9) 1.656 (42.1)
23 32 5.385 (136.8) 3.171 (80.5) 1.700 (43.2) 1.828 (46.4)
24 32 5.083 (129.1) 2.953 (75.0) 1.437 (36.5) 1.562 (39.7)
25 32 5.385 (136.8) 3.171 (80.5) 1.605 (40.8) 1.730 (43.9)
26 36 5.354 (136.0) 3.171 (80.5) 1.775 (45.1) 1.900 (48.3)
27 36 5.354 (136.0) 3.171 (80.5) 1.605 (40.8) 1.730 (43.9)
28 36 5.354 (136.0) 3.171 (80.5) 1.700 (43.2) 1.825 (46.4)
29 36 5.354 (136.0) 3.171 (80.5) 1.859 (47.2) 1.984 (50.4)
30 36 5.385 (136.8) 3.375 (85.7) 1.917 (48.7) 2.062 (52.4)
31 40 5.682 (144.3) 3.625 (92.1) 2.230 (56.6) 2.375 (60.3)
32 40 5.682 (144.3) 3.500 (88.9) 2.105 (53.5) 2.250 (57.2)
33 40 5.620 (142.7) 3.375 (85.7) 2.000 (50.8) 2.145 (54.5)
34 40 5.620 (142.7) 3.375 (85.7) 1.917 (48.7) 2.062 (52.4)
35 44 6.471 (164.4) 3.531 (89.7) 2.183 (55.4) 2.328 (59.1)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-9
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/4 Style 2
Straight Environmental Backshell
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/4 W 10 A 2
Dash Number
(Table II) Type
A or BStyle 2
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/4 Style 2
Straight Environmental Backshell
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) E
Max G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 4.000 (101.6) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 4.100 (104.1) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
16 1.0000 - 20 UNEF 1.183 (30.0) 4.400 (111.8) 1.344 (34.1) .980 (24.9) 1.125-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 4.900 (124.5) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 4.900 (124.5) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 4.900 (124.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 5.000 (127.0) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 5.300 (134.6) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 5.600 (142.2) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 5.600 (142.2) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870 (72.9) 5.725 (145.4) 2.969 (75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
TABLE II: Dash No. and Cable Range
Dash
No. Shell
Size F
± .005 (0.1) Cable Range
Min Max
1 12 1.219 (31.0) .321 (8.2) .521 (13.2)
2 14 1.344 (34.1) .446 (11.3) .646 (16.4)
3 16 1.469 (37.3) .565 (14.4) .765 (19.4)
4 18 1.625 (41.3) .690 (17.5) .890 (22.6)
5 20 1.750 (44.5) .815 (20.7) 1.015 (25.8)
6 22 2.000 (50.8) .980 (24.9) 1.180 (30.0)
7 24 2.250 (57.2) 1.230 (31.2) 1.430 (36.3)
8 24 2.250 (57.2) 1.030 (26.2) 1.230 (31.2)
9 28 2.500 (63.5) 1.430 (36.3) 1.670 (42.4)
10 32 2.750 (69.9) 1.660 (42.2) 1.860 (47.2)
11 36 3.062 (77.8) 1.860 (47.2) 2.110 (53.6)
12 40 3.437 (87.3) 2.200 (55.9) 2.400 (61.0)
13 40 3.437 (87.3) 2.200 (55.9) 2.200 (55.9)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-11
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/4 Style 3
Straight Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/4 W 10 A 3
Dash Number
(Table II) Type
A or BStyle 3
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-12
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/4 Style 3
Straight Environmental Backshell
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870 (72.9) 2.969 (75.4) .980 (24.9) 3.000-0.1P-0.2L-DS
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Size E
Max F Appr .
Free Length Cable Range
Min Max
1 12 3.810 (96.8) 4.688 (119.1) 436 (11.1) .530 (13.5)
2 12 3.248 (82.5) 4.344 (110.3) .406 (10.3) .500 (12.7)
3 12 3.810 (96.8) 3.688 (93.7) .316 (8.0) .405 (10.3)
4 14 4.024 (102.2) 6.188 (157.2) .560 (14.2) .625 (15.9)
5 14 3.712 (94.3) 5.188 (131.8) .511 (13.0) .605 (15.4)
6 14 3.712 (94.3) 4.688 (119.1) .430 (10.9) .530 (13.5)
7 14 3.712 (94.3) 3.688 (93.7) .316 (8.0) .405 (10.3)
8 18 4.087 (103.8) 6.688 (169.9) .715 (18.2) .828 (21.0)
9 20 4.212 (107.0) 7.688 (195.3) .930 (23.6) 1.055 (26.8)
10 20 4.212 (107.0) 7.188 (182.6) .875 (22.2) 1.000 (25.4)
11 20 4.150 (105.4) 7.188 (182.6) .787 (20.0) .900 (22.9)
12 20 4.150 (105.4) 7.188 (182.6) .637 (16.2) .750 (19.1)
13 22 4.212 (107.0) 7.688 (195.3) .984 (25.0) 1.109 (28.2)
14 22 4.212 (107.0) 7.188 (182.6) .875 (22.2) 1.000 (25.4)
15 24 4.275 (108.6) 9.688 (246.1) 1.250 (31.8) 1.375 (34.9)
16 24 4.275 (108.6) 8.688 (220.7) 1.185 (30.1) 1.310 (33.3)
17 24 4.275 (108.6) 8.188 (208.0) 1.105 (28.1) 1.230 (31.2)
18 24 4.275 (108.6) 8.188 (208.0) 1.055 (26.8) 1.180 (30.0)
19 28 4.337 (110.2) 10.688 (271.5) 1.406 (35.7) 1.531 (38.9)
20 28 4.337 (110.2) 9.688 (246.1) 1.320 (33.5) 1.445 (36.7)
21 28 4.337 (110.2) 9.688 (246.1) 1.250 (31.8) 1.375 (34.9)
22 32 4.704 (119.5) 13.688 (347.7) 1.700 (43.2) 1.825 (46.4)
23 32 4.704 (119.5) 13.688 (347.7) 1.605 (40.8) 1.730 (43.9)
24 32 4.399 (111.7) 12.688 (322.3) 1.531 (38.9) 1.656 (42.1)
25 36 4.704 (119.5) 14.188 (360.4) 1.917 (48.7) 2.062 (52.4)
26 36 4.673 (118.7) 13.688 (347.7) 1.859 (47.2) 1.984 (50.4)
27 36 4.673 (118.7) 13.688 (347.7) 1.775 (45.1) 1.900 (48.3)
28 36 4.673 (118.7) 13.688 (347.7) 1.700 (43.2) 1.825 (46.4)
29 36 4.673 (118.7) 13.688 (347.7) 1.605 (40.8) 1.730 (43.9)
30 40 5.000 (127.0) 18.188 (462.0) 2.230 (56.6) 2.375 (60.3)
31 40 5.000 (127.0) 17.188 (436.6) 2.105 (53.5) 2.250 (57.2)
32 40 4.939 (125.5) 14.188 (360.4) 2.000 (50.8) 2.145 (54.5)
33 40 4.939 (125.5) 14.188 (360.4) 1.917 (48.7) 2.062 (52.4)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-13
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/5 Style 1
Straight Environmental Backshell
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/5 W 10 A 1
Dash Number
(Table II) Type
A or BStyle 1
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range for the wire bundle or
cable. Dimensions shown are not intended for inspection criteria.
4. Approximate chain lengths: Dash No. 01-12 = 5.0 (127.0); Dash No. 13-29 =
6.0 (152.4).
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-14
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/5 Style 1
Straight Environmental Backshell
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Si
ze
E
Max F
± .031 (0.8) Cable Range
Min Max
1 12 3.182 (80.8) .938 (23.8) .156 (4.0) .250 (6.4)
2 18 3.901 (99.1) 1.062 (27.0) .281 (7.1) .375 (9.5)
3 18 3.932 (99.9) 1.125 (28.6) .281 (7.1) .375 (9.5)
4 18 3.901 (99.1) 1.062 (27.0) .188 (4.8) .281 (7.1)
5 18 4.177 (106.1) 1.375 (34.9) .511 (13.0) .605 (15.4)
6 18 4.177 (106.1) 1.375 (34.9) .436 (11.1) .530 (13.5)
7 20 4.489 (114.0) 1.562 (39.7) .605 (15.4) .699 (17.8)
8 20 4.489 (114.0) 1.562 (39.7) .361 (9.2) .455 (11.6)
9 20 4.306 (109.4) 1.375 (34.9) .511 (13.0) .605 (15.4)
10 22 4.584 (116.4) 1.688 (42.9) .449 (11.4) .562 (14.3)
11 22 4.306 (109.4) 1.375 (34.9) .311 (7.9) .405 (10.3)
12 22 4.306 (109.4) 1.375 (34.9) .715 (18.2) .828 (21.0)
13 24 4.647 (118.0) 1.812 (46.0) .787 (20.0) .900 (22.9)
14 24 4.647 (118.0) 1.812 (46.0) .517 (13.1) .630 (16.0)
15 24 4.647 (118.0) 1.812 (46.0) .637 (16.2) .750 (19.1)
16 24 4.647 (118.0) 1.812 (46.0) .857 (21.8) .970 (24.6)
17 24 4.542 (115.4) 1.688 (42.9) .715 (18.2) .828 (21.0)
18 24 4.647 (118.0) 1.812 (46.0) .692 (17.6) .805 (20.4)
19 28 4.896 (124.4) 2.125 (54.0) .755 (19.2) .880 (22.4)
20 28 4.896 (124.4) 2.125 (54.0) .984 (25.0) 1.109 (28.2)
21 28 4.647 (118.0) 1.812 (46.0) .637 (16.2) .750 (19.1)
22 28 4.229 (107.4) 1.125 (28.6) .281 (7.1) .375 (9.5)
23 28 4.647 (118.0) 1.812 (46.0) .857 (21.8) .970 (24.6)
24 28 4.896 (124.4) 2.125 (54.0) .875 (22.2) 1.000 (25.4)
25 28 4.431 (112.5) 1.375 (34.9) .436 (11.1) .530 (13.5)
26 28 4.647 (118.0) 1.812 (46.0) .567 (14.4) .680 (17.3)
27 32 4.896 (124.4) 2.125 (54.0) .930 (23.6) 1.055 (26.8)
28 32 4.959 (126.0) 2.469 (62.7) 1.105 (28.1) 1.230 (31.2)
29 32 4.647 (118.0) 1.812 (46.0) .637 (16.2) .750 (19.1)
30 32 4.896 (124.4) 2.125 (54.0) .755 (19.2) .880 (22.4)
31 32 4.896 (124.4) 2.125 (54.0) .984 (25.0) 1.109 (28.2)
32 32 4.647 (118.0) 1.812 (46.0) .857 (21.8) .970 (24.6)
33 32 4.276 (108.6) 1.125 (28.6) .281 (7.1) .375 (9.5)
34 32 4.431 (112.5) 1.375 (34.9) .436 (11.1) .530 (13.5)
35 32 4.959 (126.0) 2.469 (62.7) 1.005 (25.5) 1.130 (28.7)
36 36 4.959 (126.0) 2.469 (62.7) 1.185 (30.1) 1.310 (33.3)
37 36 4.896 (124.4) 2.125 (54.0) .984 (25.0) 1.109 (28.2)
38 36 5.021 (127.5) 2.625 (66.7) 1.250 (31.8) 1.375 (34.9)
39 36 4.959 (126.0) 2.469 (62.7) 1.055 (26.8) 1.180 (30.0)
40 36 5.021 (127.5) 2.625 (66.7) 1.320 (33.5) 1.445 (36.7)
41 36 4.651 (118.1) 1.812 (46.0) .857 (21.8) .970 (24.6)
42 36 4.959 (126.0) 2.469 (62.7) 1.105 (28.1) 1.230 (31.2)
43 40 6.354 (161.4) 3.171 (80.5) 1.815 (46.1) 1.940 (49.3)
44 40 6.354 (161.4) 3.171 (80.5) 1.700 (43.2) 1.825 (46.4)
45 40 6.354 (161.4) 3.171 (80.5) 1.605 (40.8) 1.730 (43.9)
46 40 6.057 (153.8) 2.953 (75.0) 1.531 (38.9) 1.656 (42.1)
47 44 6.345 (161.2) 3.375 (85.7) 1.867 (47.4) 2.000 (50.8)
48 44 5.266 (133.8) 3.171 (80.5) 1.775 (45.1) 1.900 (48.3)
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870 (72.9) 2.969 (75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
44 2.8750 - 16 UN 3.120 (79.2) 3.217 (81.7) .980 (24.9) 3.000-0.1P-0.2L-DS
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-15
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/5 Style 2
Straight Environmental Backshell
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/5 W 10 A 2
Dash Number
(Table II) Type
A or BStyle 2
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-16
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/5 Style 2
Straight Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
4. Approximate chain lengths: Dash
No. 01-12 = 5.0 (127.0); Dash No.
13-29 = 6.0 (152.4).
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Size F
± .031 (0.8) Cable Range
Min Max
1 12 .969 (24.6) .130 (3.3) .280 (7.1)
2 14 1.094 (27.8) .246 (6.2) .396 (10.1)
3 16 1.219 (31.0) .321 (8.2) .521 (13.2)
4 18 1.344 (34.1) .446 (11.3) .646 (16.4)
5 18 1.344 (34.1) .300 (7.6) .475 (12.1)
6 20 1.469 (37.3) .565 (14.4) .765 (19.4)
7 20 1.469 (37.3) .400 (10.2) .600 (15.2)
8 22 1.625 (41.3) .690 (17.5) .890 (22.6)
9 22 1.625 (41.3) .500 (12.7) .700 (17.8)
10 22 1.625 (41.3) .400 (10.2) .525 (13.3)
11 24 1.750 (44.5) .815 (20.7) 1.015 (25.8)
12 24 1.750 (44.5) .595 (15.1) .815 (20.7)
13 28 2.000 (50.8) .980 (24.9) 1.180 (30.0)
14 28 2.000 (50.8) .780 (19.8) .980 (24.9)
15 32 2.250 (57.2) 1.230 (31.2) 1.430 (36.3)
16 32 2.250 (57.2) 1.030 (26.2) 1.230 (31.2)
17 36 2.500 (63.5) 1.470 (37.3) 1.670 (42.4)
18 36 2.500 (63.5) 1.270 (32.3) 1.470 (37.3)
19 40 2.750 (69.9) 1.660 (42.2) 1.860 (47.2)
20 40 2.750 (69.9) 1.400 (35.6) 1.660 (42.2)
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) E
Max G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 4.000 (101.6) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
14 .8750 - 20 UNEF 1.057 (26.8) 4.100 (104.1) 1.219 (31.0) .765 (19.4) 1.000-0.1P-0.2L-DS
16 1.0000 - 20 UNEF 1.183 (30.0) 4.400 (111.8) 1.344 (34.1) .980 (24.9) 1.125-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 4.600 (116.8) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 4.900 (124.5) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 4.900 (124.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 5.000 (127.0) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 5.300 (134.6) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.057 (52.2) 5.600 (142.2) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 5.600 (142.2) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.870 (72.9) 5.725 (145.4) 2.969 (75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-17
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/5 Style 3
Straight Environmental Backshell
CONNECTOR DESIGNATOR:
CMIL-DTL-22992 Classes C, J and R
Basic
Part Number
M85049/5 W 10 A 3
Dash Number
(Table II) Type
A or BStyle 3
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range for the wire bundle or
cable. Dimensions shown are not intended for inspection criteria.
4. Approximate chain lengths: Dash No. 01-12 = 5.0 (127.0); Dash No. 13-29 =
6.0 (152.4).
Finish
A = Black Anodize X = Nickel Fluorocarbon Polymer
W = Cadmium, Olive Drab Z = Zinc Nickel
Y = Pure Dense
Electrodeposited Aluminum
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-18
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/5 Style 3
Straight Environmental Backshell
TABLE II: Dash Number, Shell Size and Cable Range
Dash
No. Shell
Size Cable Range
Min Max E
Max F Appr .
Free Length
1 12 .160 (4.1) .222 (5.6) 2.752 (69.9) 2.406 (61.1)
2 18 .511 (13.0) .605 (15.4) 3.712 (94.3) 5.188 (131.8)
3 18 .436 (11.1) .530 (13.5) 3.712 (94.3) 4.688 (119.1)
4 18 .306 (7.8) .375 (9.5) 3.502 (89.0) 3.844 (97.6)
5 18 .219 (5.6) .281 (7.1) 3.471 (88.2) 2.844 (72.2)
6 20 .605 (15.4) .699 (17.8) 4.024 (102.2) 6.188 (157.2)
7 20 .511 (13.0) .605 (15.4) 3.841 (97.6) 5.188 (131.8)
8 20 .361 (9.2) .455 (11.6) 4.024 (102.2) 4.188 (106.4)
9 22 .715 (18.2) .828 (21.0) 4.087 (103.8) 6.688 (169.9)
10 22 .449 (11.4) .562 (14.3) 4.087 (103.8) 5.188 (131.8)
11 22 .316 (8.0) .405 (10.3) 3.841 (97.6) 3.688 (93.7)
12 24 .692 (17.6) .805 (20.4) 4.150 (105.4) 6.688 (169.9)
13 24 .637 (16.2) .750 (19.1) 4.150 (105.4) 6.688 (169.9)
14 24 .517 (13.1) .630 (16.0) 4.150 (105.4) 5.688 (144.5)
15 28 .984 (25.0) 1.109 (28.2) 4.212 (107.0) 7.688 (195.3)
16 28 .875 (22.2) 1.000 (25.4) 4.212 (107.0) 7.188 (182.6)
17 28 .755 (19.2) .880 (22.4) 4.212 (107.0) 6.688 (169.9)
18 28 .637 (16.2) .750 (19.1) 4.150 (105.4) 6.688 (169.9)
19 28 .567 (14.4) .680 (17.3) 4.150 (105.4) 6.688 (169.9)
20 28 .436 (11.1) .530 (13.5) 3.966 (100.7) 4.688 (119.1)
21 28 .306 (7.8) .375 (9.5) 3.799 (96.5) 3.844 (97.6)
22 32 1.105 (28.1) 1.230 (31.2) 4.275 (108.6) 8.188 (208.0)
23 32 1.005 (25.5) 1.130 (28.7) 4.275 (108.6) 7.188 (182.6)
24 32 .930 (23.6) 1.055 (26.8) 4.212 (107.0) 7.688 (195.3)
25 32 .857 (21.8) .970 (24.6) 4.150 (105.4) 7.188 (182.6)
26 32 .755 (19.2) .880 (22.4) 4.212 (107.0) 6.688 (169.9)
27 32 .637 (16.2) .750 (19.1) 4.150 (105.4) 6.688 (169.9)
28 32 .436 (11.1) .530 (13.5) 3.966 (100.7) 4.688 (119.1)
29 32 .306 (7.8) .375 (9.5) 3.846 (97.7) 3.844 (97.6)
30 36 1.320 (33.5) 1.445 (36.7) 4.337 (110.2) 9.688 (246.1)
31 36 1.250 (31.8) 1.375 (34.9) 4.337 (110.2) 9.688 (246.1)
32 36 1.185 (30.1) 1.310 (33.3) 4.275 (108.6) 8.688 (220.7)
33 36 1.105 (28.1) 1.230 (31.2) 4.275 (108.6) 8.188 (208.0)
34 36 1.055 (26.8) 1.180 (30.0) 4.275 (108.6) 8.188 (208.0)
35 36 .984 (25.0) 1.109 (28.2) 4.212 (107.0) 7.688 (195.3)
36 36 .857 (21.8) .970 (24.6) 4.154 (105.5) 7.188 (182.6)
37 40 1.815 (46.1) 1.940 (49.3) 5.673 (144.1) 13.188 (335.0)
38 40 1.700 (43.2) 1.825 (46.4) 5.673 (144.1) 13.188 (335.0)
39 40 1.605 (40.8) 1.730 (43.9) 5.673 (144.1) 13.188 (335.0)
40 40 1.531 (38.9) 1.656 (42.1) 5.373 (136.5) 12.688 (322.3)
41 44 1.862 (47.3) 2.000 (50.8) 5.673 (144.1) 14.188 (360.4)
42 44 1.775 (45.1) 1.900 (48.3) 4.594 (116.7) 12.688 (322.3)
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B-LH B Dia
±.015 (0.4) G Dia
Max H
Max J Thread (Plated)
Class 2 (A or B)
12 .7500 - 20 UNEF .933 (23.7) 1.094 (27.8) .765 (19.4) 0.875-0.1P-0.2L-DS
18 1.1250 - 18 UNEF 1.307 (33.2) 1.469 (37.3) .980 (24.9) 1.250-0.1P-0.2L-DS
20 1.2500 - 18 UNEF 1.433 (36.4) 1.562 (39.7) .980 (24.9) 1.375-0.1P-0.2L-DS
22 1.3750 - 18 UNEF 1.557 (39.5) 1.688 (42.9) .980 (24.9) 1.500-0.1P-0.2L-DS
24 1.6250 - 18 UNEF 1.807 (45.9) 1.938 (49.2) .980 (24.9) 1.750-0.1P-0.2L-DS
28 1.8750 - 16 UN 2.057 (52.2) 2.219 (56.4) .980 (24.9) 2.000-0.1P-0.2L-DS
32 2.0625 - 16 UNS 2.307 (58.6) 2.469 (62.7) .980 (24.9) 2.250-0.1P-0.2L-DS
36 2.3125 - 16 UNS 2.557 (64.9) 2.719 (69.1) .980 (24.9) 2.500-0.1P-0.2L-DS
40 2.6250 - 16 UN 2.875 (73.0) 2.969 (75.4) .980 (24.9) 2.750-0.1P-0.2L-DS
44 2.8750 - 16 UN 3.125 (79.4) 3.217 (81.7) .980 (24.9) 3.000-0.1P-0.2L-DS
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-19
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/6 and MS3189A
45° EMI/RFI Environmental Backshell
Superseded
Part Number
MS3189A 21 C
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. When maximum cable entry is
exceeded, Style 2 will be supplied.
3. Metric dimensions (mm) are in
parentheses.
4. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE I: Dash Number, Cable Range and Dimensions
Dash
No. Shell
Size F
Max G
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
1 3 .686 (17.4) 2.034 (51.7) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
2 3 1.500 (38.1) 1.306 (33.2) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
3 8 .625 (15.9) 1.974 (50.1) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
4 10 .686 (17.4) 1.369 (34.8) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
5 10 .686 (17.4) 2.034 (51.7) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
6 12 .750 (19.1) 2.034 (51.7) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
7 12 .750 (19.1) 2.034 (51.7) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
8 12 .750 (19.1) 2.124 (53.9) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .813 (20.7) 1.779 (45.2) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
10 14 .813 (20.7) 2.234 (56.7) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 .906 (23.0) 1.874 (47.6) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 16 .906 (23.0) 2.424 (61.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.093 (27.8) 2.062 (52.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.093 (27.8) 2.424 (61.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.093 (27.8) 2.062 (52.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.093 (27.8) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.188 (30.2) 2.217 (56.3) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.188 (30.2) 2.574 (65.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.188 (30.2) 2.217 (56.3) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.188 (30.2) 2.624 (66.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.313 (33.4) 2.562 (65.1) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-20
CONNECTOR DESIGNATOR:
A
AS50151 Series 34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
Basic
Part Number
M85049/6 -21 W
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-20
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/6 and MS3189A
45° EMI/RFI Environmental Backshell
* Denotes Style 2
TABLE I: Continued from Page B-19
Dash
No. Shell
Size F
Max G
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.312 (33.3) 2.280 (57.9) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.375 (34.9) 2.724 (69.2) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.375 (34.9) 2.724 (69.2) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.375 (34.9) 2.374 (60.3) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.406 (35.7) 2.814 (71.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.406 (35.7) 2.814 (71.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.406 (35.7) 2.468 (62.7) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.156 (54.8) 2.634 (66.9) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.156 (54.8) 2.634 (66.9) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.156 (54.8) 2.468 (62.7) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.156 (54.8) 2.814 (71.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.156 (54.8) 2.468 (62.7) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.156 (54.8) 2.468 (62.7) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.156 (54.8) 2.814 (71.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.156 (54.8) 2.814 (71.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.156 (54.8) 2.468 (62.7) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.188 (30.2) 2.574 (65.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.188 (30.2) 2.217 (56.3) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 .906 (23.0) 2.234 (56.7) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.093 (27.8) 2.424 (61.6) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
42 18 1.093 (27.8) 2.424 (61.6) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
43 20 1.093 (27.8) 2.424 (61.6) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
44 22 1.188 (30.2) 2.574 (65.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
45 22 1.188 (30.2) 2.574 (65.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
46 24 1.188 (30.2) 2.574 (65.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.406 (35.7) 2.814 (71.5) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 2.156 (54.8) 2.814 (71.5) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.500 (38.1) 2.034 (51.7) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
50* 14 1.842 (46.8) 2.424 (61.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 1.937 (49.2) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.093 (27.8) 2.424 (61.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.188 (30.2) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.093 (27.8) 2.424 (61.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.061 (52.3) 2.624 (66.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.188 (30.2) 2.574 (65.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.188 (30.2) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.061 (52.3) 2.624 (66.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.188 (30.2) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.313 (33.4) 2.624 (66.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.313 (33.4) 2.624 (66.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.375 (34.9) 2.724 (69.2) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.406 (35.7) 2.814 (71.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.406 (35.7) 2.814 (71.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.156 (54.8) 2.814 (71.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.156 (54.8) 2.814 (71.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
67 44 2.156 (54.8) 2.814 (71.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.156 (54.8) 2.814 (71.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.156 (54.8) 2.814 (71.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.156 (54.8) 2.814 (71.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.654 (42.0) 2.234 (56.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 1.937 (49.2) 2.574 (65.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.061 (52.3) 2.624 (66.6) 2.230 (56.6) 2.116 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .813 (20.7) 2.124 (53.9) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 04
75 16 .906 (23.0) 2.234 (56.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 04
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-21
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/7 and MS3189B
45° Environmental Backshell
Basic
Part Number
M85049/7 -21 N
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr . Cadmium Olive Drab over Electroless Nickel /
Aluminum
X = Nickel Fluorocarbon Polymer / Aluminum
Y = Pure Dense Electrodeposited Aluminum / Aluminum
Z = Zinc Nickel, Black / Aluminum
XS = Nickel Fluorocarbon Polymer / Stainless Steel
YS =
Pure Dense Electrodeposited Aluminum / Stainless Steel
ZS = Zinc Nickel, Black / Stainless Steel
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are
in parentheses.
3. When maximum cable entry
is exceeded, Style 2 will be
supplied.
4. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are
not intended for inspection
criteria.
5. Approximate chain lengths:
Dash No. 01-12 = 5.0
(127.0); Dash No. 13-29 =
6.0 (152.4).
Superseded
Part Number
MS3189B 21 N
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
TABLE II: Dash Number and Cable Range
Dash
No. Shell
Size F
Max G
± .125 (3.2) K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
1 03 .688 (17.5) 1.852 (47.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
2 03 1.500 (38.1) 1.972 (50.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
3 08 .625 (15.9) 1.244 (31.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
4 10 .688 (17.5) 1.912 (48.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
5 10 .688 (17.5) 1.307 (33.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
6 12 .750 (19.1) 1.972 (50.1) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
7 12 .750 (19.1) 1.972 (50.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
8 12 .750 (19.1) 1.972 (50.1) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .812 (20.6) 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
10 14 .812 (20.6) 1.717 (43.6) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 .906 (23.0) 2.172 (55.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 16 .906 (23.0) 1.812 (46.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.093 (27.8) 2.362 (60.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.093 (27.8) 2.000 (50.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.093 (27.8) 2.362 (60.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.093 (27.8) 2.000 (50.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.188 (30.2) 2.512 (63.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.188 (30.2) 2.155 (54.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.188 (30.2) 2.512 (63.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.188 (30.2) 2.093 (53.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.312 (33.3) 2.500 (63.5) 1.156 (33.7) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Table Continued on Page B-22
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-22
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/7 and MS3189B
45° Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued From Page B-21)
Dash
No. Shell
Size F
Max G
± .125 (3.2) K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.312 (33.3) 2.218 (56.3) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.375 (34.9) 2.662 (67.6) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.375 (34.9) 2.662 (67.6) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.375 (34.9) 2.312 (58.7) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.406 (35.7) 2.752 (69.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.406 (35.7) 2.752 (69.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.406 (35.7) 2.406 (61.1) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.156 (54.8) 2.752 (69.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.156 (54.8) 2.752 (69.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.156 (54.8) 2.406 (61.1) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.156 (54.8) 2.752 (69.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.156 (54.8) 2.752 (69.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.156 (54.8) 2.406 (61.1) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.156 (54.8) 2.752 (69.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.156 (54.8) 2.752 (69.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.156 (54.8) 2.406 (61.1) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.188 (30.2) 2.512 (63.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.188 (30.2) 2.155 (54.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 .906 (23.0) 2.172 (55.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.093 (27.8) 2.362 (60.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
42 18 1.093 (27.8) 2.362 (60.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
43 20 1.093 (27.8) 2.362 (60.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
44 22 1.188 (30.2) 2.512 (63.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
45 22 1.188 (30.2) 2.512 (63.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
46 24 1.188 (30.2) 2.512 (63.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.406 (35.7) 2.752 (69.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 2.156 (54.8) 2.752 (69.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.500 (38.1) 1.972 (50.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
50* 14 1.842 (46.8) 2.362 (60.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 1.938 (49.2) 2.512 (63.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.093 (27.8) 2.362 (60.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.188 (30.2) 2.512 (63.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.093 (27.8) 2.362 (60.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.061 (52.3) 2.562 (65.1) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.188 (30.2) 2.512 (63.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.188 (30.2) 2.512 (63.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.061 (52.3) 2.562 (65.1) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.188 (30.2) 2.512 (63.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.312 (33.3) 2.562 (65.1) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.312 (33.3) 2.562 (65.1) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.375 (34.9) 2.662 (67.6) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.406 (35.7) 2.752 (69.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.406 (35.7) 2.752 (69.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.156 (54.8) 2.752 (69.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.156 (54.8) 2.752 (69.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
67 44 2.156 (54.8) 2.752 (69.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.156 (54.8) 2.752 (69.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.156 (54.8) 2.752 (69.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.156 (54.8) 2.752 (69.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.654 (42.0) 2.173 (55.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 1.938 (49.2) 2.512 (63.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.061 (52.3) 2.562 (65.1) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .812 (20.6) 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
75 16 .906 (23.0) 2.172 (55.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-23
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
STYLE 2 A Thread (Table I),
Page 39-11
AS85049/8 and MS3188A
90° EMI/RFI Environmental Backshell
Basic
Part Number
M85049/8 -21 W
Dash Number
(Table II) Superseded
Part Number
MS3188A 21 C
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. When maximum cable entry is exceeded,
Style 2 will be supplied.
3. Metric dimensions (mm) are in
parentheses.
4. Cable Range is dened as the
accommodation range for the wire bundle
or cable. Dimensions shown are not
intended for inspection criteria.
TABLE I: Dash Number, Cable Range and Dimensions
Dash
No. Shell
Size H
Max J
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
1 3 .761 (19.3) 1.924 (48.9) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
2 3 1.511 (38.4) 1.444 (36.7) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
3 8 .666 (16.9) 1.324 (33.6) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
4 10 .761 (19.3) 2.044 (51.9) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
5 10 .761 (19.3) 1.444 (36.7) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
6 12 .766 (19.5) 2.064 (52.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
7 12 .766 (19.5) 2.064 (52.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
8 12 .766 (19.5) 1.459 (37.1) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .866 (22.0) 2.134 (54.2) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
10 14 .866 (22.0) 1.779 (45.2) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 1.051 (26.7) 2.224 (56.5) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 16 1.051 (26.7) 1.869 (47.5) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.141 (29.0) 2.394 (60.8) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.141 (29.0) 2.044 (51.9) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.141 (29.0) 2.394 (60.8) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.141 (29.0) 2.044 (51.9) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.291 (32.8) 2.504 (63.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.291 (32.8) 2.149 (54.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.291 (32.8) 2.504 (63.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.291 (32.8) 2.149 (54.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.391 (35.3) 2.674 (67.9) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-23
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11,
LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2,
PATT 602
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-24
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/8 and MS3188A
90° EMI/RFI Environmental Backshell
* Denotes Style 2
TABLE I: Continued from Page B-23
Dash
No. Shell
Size H
Max J
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.391 (35.3) 2.319 (58.9) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.741 (44.2) 2.924 (74.3) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.741 (44.2) 2.924 (74.3) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.741 (44.2) 2.569 (65.3) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.941 (49.3) 2.894 (73.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.941 (49.3) 2.894 (73.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.941 (49.3) 2.539 (64.5) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.691 (68.4) 2.894 (73.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.691 (68.4) 2.894 (73.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.691 (68.4) 2.539 (64.5) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.691 (68.4) 2.894 (73.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.691 (68.4) 2.894 (73.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.691 (68.4) 2.539 (64.5) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.691 (68.4) 2.894 (73.5) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.691 (68.4) 2.894 (73.5) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.691 (68.4) 2.539 (64.5) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.291 (32.8) 2.504 (63.6) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.291 (32.8) 2.149 (54.6) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 1.051 (26.7) 2.224 (56.5) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.141 (29.0) 2.394 (60.8) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
42 18 1.141 (29.0) 2.394 (60.8) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
43 20 1.141 (29.0) 2.394 (60.8) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
44 22 1.291 (32.8) 2.504 (63.6) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
45 22 1.291 (32.8) 2.504 (63.6) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
46 24 1.291 (32.8) 2.504 (63.6) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.941 (49.3) 2.894 (73.5) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 1.941 (49.3) 2.894 (73.5) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.516 (38.5) 2.064 (52.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
50* 14 1.891 (48.0) 2.394 (60.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 2.041 (51.8) 2.504 (63.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.141 (29.0) 2.394 (60.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.291 (32.8) 2.149 (54.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.141 (29.0) 2.394 (60.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.141 (54.4) 2.674 (67.9) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.291 (32.8) 2.504 (63.6) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.291 (32.8) 2.504 (63.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.141 (54.4) 2.674 (67.9) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.291 (32.8) 2.504 (63.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.391 (35.3) 2.674 (67.9) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.391 (35.3) 2.674 (67.9) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.741 (44.2) 2.924 (74.3) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.941 (49.3) 2.894 (73.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.941 (49.3) 2.894 (73.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.691 (68.4) 2.894 (73.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.691 (68.4) 2.894 (73.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
67 44 2.691 (68.4) 2.894 (73.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.691 (68.4) 2.894 (73.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.691 (68.4) 2.894 (73.5) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.691 (68.4) 2.894 (73.5) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.811 (46.0) 2.224 (56.5) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 2.051 (52.1) 2.504 (63.6) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.151 (54.6) 2.674 (67.9) 2.230 (56.6) 2.116 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .866 (22.0) 2.134 (54.2) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 04
75 16 1.051 (26.7) 2.224 (56.5) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 04
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-25
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/9 and MS3188B
90° Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued on Page B-26)
Dash
No.
Shell
Size
H
Max
J
Max
K
Ref.
L
Max
Cable Range
Min Max
M85049/42
Ref.
1 03 .761 (19.3) 1.862 (47.3) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
2 03 1.511 (38.4) 1.382 (35.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
3 08 .666 (16.9) 1.262 (32.1) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
4 10 .761 (19.3) 1.982 (50.3) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
5 10 .761 (19.3) 1.382 (35.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
6 12 .766 (19.5) 2.002 (50.9) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
7 12 .766 (19.5) 2.002 (50.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
8 12 .766 (19.5) 1.397 (35.5) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .866 (22.0) 2.072 (52.6) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
10 14 .866 (22.0) 1.717 (43.6) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 1.051 (26.7) 2.162 (54.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 16 1.051 (26.7) 1.807 (45.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.141 (29.0) 2.332 (59.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.141 (29.0) 1.982 (50.3) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.141 (29.0) 2.332 (59.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.141 (29.0) 1.982 (50.3) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.291 (32.8) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.291 (32.8) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.291 (32.8) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.291 (32.8) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.391 (35.3 2.612 (66.3) 1.156 (33.7) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Superseded
Part Number
MS3188B 21 N
Basic
Part No.
Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. When maximum cable entry is exceeded, Style 2
will be supplied.
4. Cable Range is dened as the accommodation
range for the wire bundle or cable. Dimensions
shown are not intended for inspection criteria.
5. Approximate chain lengths: Dash No. 01-12 = 5.0
(127.0); Dash No. 13-29 = 6.0 (152.4).
Table Continued on Page B-26
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
Basic
Part Number
M85049/9 -21 N
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel
XS = Nickel Fluorocarbon Polymer / Stainless Steel
YS =
Pure Dense Electrodeposited Aluminum / Stainless Steel
ZS = Zinc Nickel, Black / Stainless Steel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-26
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/9 and MS3188B
90° Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued From Page B-25
Dash
No. Shell
Size H
Max J
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.391 (35.3) 2.257 (57.3) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.741 (44.2) 2.862 (72.7) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.741 (44.2) 2.862 (72.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.741 (44.2) 2.507 (63.7) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.941 (49.3) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.941 (49.3) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.941 (49.3) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.691 (68.4) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.691 (68.4) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.691 (68.4) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.691 (68.4) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.691 (68.4) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.691 (68.4) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.691 (68.4) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.691 (68.4) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.691 (68.4) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.291 (32.8) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.291 (32.8) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 1.051 (26.7) 2.162 (54.9) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.141 (29.0) 2.332 (59.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
42 18 1.141 (29.0) 2.332 (59.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
43 20 1.141 (29.0) 2.332 (59.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
44 22 1.291 (32.8) 2.442 (62.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
45 22 1.291 (32.8) 2.442 (62.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
46 24 1.291 (32.8) 2.442 (62.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.941 (49.3) 2.832 (71.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 1.941 (49.3) 2.832 (71.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.516 (38.5) 2.002 (50.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
50* 14 1.891 (48.0) 2.332 (59.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 2.041 (51.8) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.141 (29.0) 2.332 (59.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.291 (32.8) 2.087 (53.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.141 (29.0) 2.332 (59.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.141 (54.4) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.291 (32.8) 2.442 (62.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.291 (32.8) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.141 (54.4) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.291 (32.8) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.391 (35.3) 2.612 (66.3) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.391 (35.3) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.741 (44.2) 2.862 (72.7) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.941 (49.3) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.941 (49.3) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.691 (68.4) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.691 (68.4) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
67 44 2.691 (68.4) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.691 (68.4) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.691 (68.4) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.691 (68.4) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.811 (46.0) 2.162 (54.9) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 2.051 (52.1) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.151 (54.6) 2.612 (66.3) 1.375 (34.9) 2.116 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .866 (22.0) 2.072 (52.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
75 16 1.051 (26.7) 2.162 (54.9) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-27
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/10 and MS3437A
Straight EMI/RFI Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE I: Shell Size
and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max
3.562 - 24 UNEF .67 (17.0)
8 .500 - 20 UNF .62 (15.7)
10 .625 - 24 UNEF .73 (18.5)
12 .750 - 20 UNEF .86 (21.8)
14 .875 - 20 UNEF .98 (24.9)
16 1.000 - 20 UNEF 1.11 (28.2)
18 1.062 - 18 UNEF 1.22 (31.0)
20 1.188 - 18 UNEF 1.34 (34.0)
22 1.313 - 18 UNEF 1.47 (37.3)
24 1.438 - 18 UNEF 1.59 (40.4)
28 1.750 - 18 UNS 1.97 (50.0)
32 2.000 - 18 UNS 2.22 (56.4)
36 2.250 - 16 UN 2.47 (62.7)
40 2.500 - 16 UN 2.72 (69.1)
44 2.750 - 16 UN 2.97 (75.4)
48 3.000 - 16 UN 3.22 (81.8)
61 1.500 - 18 UNEF 1.65 (41.9)
Superseded
Part Number
MS3437A 21 C
Basic
Part No. Dash
No.
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
Basic
Part Number
M85049/10 -21 W
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-28
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/10 and MS3437A
Straight EMI/RFI Environmental Backshell
TABLE II: Dash No., Style, Shell Size, Dimensions and Cable Range
Dash
No. Shell
Size Style E
Max K
Ref L
Max Cable Range
Min Max M85049/42
Ref.
01 3 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
02 3 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
03 3 2 2.875 (73.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
04 3 2 3.875 (98.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
05 8 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
06 8 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .250 (6.4) 4
07 8 2 2.875 (73.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
08 8 2 3.875 (98.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
09 10 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
10 10 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
11 10 2 2.875 (73.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 10 2 3.875 (98.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
13 12 1 2.125 (54.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
14 12 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
15 12 2 2.875 (73.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 12 2 3.875 (98.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
17 14 1 2.125 (54.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
18 14 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
19 14 2 2.875 (73.0) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 14 2 3.875 (98.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
21 16 1 2.125 (54.0) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
22 16 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
23 16 2 2.875 (73.0) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 16 2 3.875 (98.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
25 18 1 2.125 (54.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
26 18 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
27 18 1 2.125 (54.0) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
28 18 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
29 18 2 2.875 (73.0) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 18 2 3.875 (98.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
31 20 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
32 20 1 4.125 (104.8) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
33 20 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
34 20 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
35 20 2 3.875 (98.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 20 2 4.875 (123.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
37 20 2 3.875 (98.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
38 20 2 4.875 (123.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
39 22 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
40 22 1 4.125 (104.8) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 22 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
42 22 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
43 22 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
44 22 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
45 22 2 3.875 (98.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
46 22 2 4.875 (123.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
47 24 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 24 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49 24 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
50 24 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
51 24 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 24 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-29
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-29
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/10 and MS3437A
Straight EMI/RFI Environmental Backshell
TABLE II: (Continued from Page B-28)
Dash
No. Shell
Size Style E
Max K
Ref L
Max Cable Range
Min Max M85049/42
Ref.
53 24 2 3.875 (98.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
54 24 2 4.875 (123.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
55 28 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
56 28 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
57 28 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58 28 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
59 28 1 3.125 (79.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
60 28 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
61 28 1 3.125 (79.4) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
62 28 1 4.126 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 32 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
64 32 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
65 32 1 3.125 (79.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 32 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
67 32 1 3.125 (79.4) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
68 32 1 4.125 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
69 32 1 3.125 (79.4) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
70 32 1 4.125 (104.8) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71 36 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
72 36 1 5.125 (130.2) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
73 36 1 4.125 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
74 36 1 5.125 (130.2) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
75 36 1 4.125 (104.8) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
76 36 1 5.125 (130.2) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
77 36 2 5.000 (127.0) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
78 36 2 6.000 (152.4) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
79 40 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
80 40 1 5.125 (130.2) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
81 40 1 4.125 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
82 40 1 5.125 (130.2) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
83 40 1 4.125 (104.8) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
84 40 1 5.125 (130.2) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
85 40 1 4.125 (104.8) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
86 40 1 5.125 (130.2) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
87 44 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
88 44 1 5.125 (130.2) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
89 44 1 4.125 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
90 44 1 5.125 (130.2) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
91 44 1 4.125 (104.8) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
92 44 1 5.125 (130.2) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
93 44 1 4.125 (104.8) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
94 44 1 5.125 (130.2) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
95 48 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
96 48 1 5.125 (130.2) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
97 48 1 4.125 (104.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
98 48 1 5.125 (130.2) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
99 48 1 4.125 (104.8) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
100 48 1 5.125 (130.2) 2.550 (64.8) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
101 48 1 4.125 (104.8) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
102 48 1 5.125 (130.2) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
103 61 1 3.125 (79.4) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
104 61 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
Continued on Page B-30
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-30
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/10 and MS3437A
Straight EMI/RFI Environmental Backshell
TABLE II: (Continued from Page B-29
Dash
No. Shell
Size Style E
Max K
Ref L
Max Cable Range
Min Max M85049/42
Ref.
105 61 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
106 61 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
107 61 2 3.875 (98.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
108 61 2 4.875 (123.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
109 61 2 3.875 (98.4) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
110 61 2 4.875 (123.8) 2.024 (51.4) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
111 12 1 2.125 (54.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
112 16 1 2.125 (54.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
113 16 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
114 12 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
115 12 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
116 14 1 2.125 (54.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
117 14 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
118 16 1 2.125 (54.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
119 16 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
120 18 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
121 18 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
122 18 1 2.125 (54.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
123 18 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
124 20 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
125 20 1 4.125 (104.8) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
126 22 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
127 22 1 4.125 (104.8) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
128 22 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
129 22 1 4.125 (104.8) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
130 24 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
131 24 1 4.125 (104.8) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
132 36 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
133 36 1 5.125 (130.2) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
134 40 1 4.125 (104.8) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
135 40 1 5.125 (130.2) 1.916 (48.7) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
136 10 1 2.125 (54.0) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
137 10 1 3.125 (79.4) 1.544 (39.2) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
138 12 1 2.125 (54.0) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
139 12 1 3.125 (79.4) 1.844 (46.8) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
140 20 1 3.125 (79.4) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
141 20 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
142 22 1 3.125 (79.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
143 22 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
144 24 1 3.125 (79.4) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
145 24 1 4.125 (104.8) 2.230 (56.6) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
146 36 1 4.125 (104.8) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
147 36 1 5.125 (130.2) 2.600 (66.0) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
148 36 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
149 36 1 5.125 (130.2) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
150 14 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
151 14 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
152 16 1 2.125 (54.0) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
153 16 1 3.125 (79.4) 1.544 (39.2) .957 (24.3) .125 (3.2) .312 (7.9) 4
154 44 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
155 44 1 5.125 (130.2) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
156 40 1 4.125 (104.8) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
157 40 1 5.125 (130.2) 2.000 (50.8) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-31
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/11 and MS3437B
Straight Environmental Backshell
Superseded
Part Number
MS3437B 21 N
Basic
Part No.
Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are
in parentheses.
3. When maximum cable entry
is exceeded, Style 2 will be
supplied.
4. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are
not intended for inspection
criteria.
TABLE I: Shell Size and Dimensions
Shell
Size
A Thread
Class 2B-LH
C Dia
Max
3.562 - 24 UNEF .669 (17.0)
8 .500 - 20 UNF .617 (15.7)
10 .625 - 24 UNEF .734 (18.6)
12 .750 - 20 UNEF .858 (21.8)
14 .875 - 20 UNEF .984 (25.0)
16 1.000 - 20 UNEF 1.112 (28.2)
18 1.062 - 18 UNEF 1.218 (30.9)
20 1.188 - 18 UNEF 1.345 (34.2)
22 1.313 - 18 UNEF 1.468 (37.3)
24 1.438 - 18 UNEF 1.593 (40.5)
28 1.750 - 18 UNS 1.969 (50.0)
32 2.000 - 18 UNS 2.219 (56.4)
36 2.250 - 16 UN 2.469 (62.7)
40 2.500 - 16 UN 2.719 (69.1)
44 2.750 - 16 UN 2.969 (75.4)
48 3.000 - 16 UN 3.219 (81.8)
61 1.500 - 18 UNEF 1.653 (42.0)
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
Basic
Part Number
M85049/11 -21 N
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel /
Aluminum
X = Nickel Fluorocarbon Polymer / Aluminum
Y = Pure Dense Electrodeposited Aluminum / Aluminum
Z = Zinc Nickel, Black / Aluminum
XS = Nickel Fluorocarbon Polymer / Stainless Steel
YS = Pure Dense Electrodeposited Aluminum / Stainless Steel
ZS = Zinc Nickel, Black / Stainless Steel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-32
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/11 and MS3437B
Straight Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued on Page B-33)
Dash
No. Shell
Size Style E
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
01 3 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
02 3 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
03 3 2 2.875 (73.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
04 3 2 3.875 (98.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
05 8 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
06 8 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
07 8 2 2.875 (73.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
08 8 2 3.875 (98.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
09 10 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
10 10 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
11 10 2 2.875 (73.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 10 2 3.875 (98.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
13 12 1 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
14 12 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
15 12 2 2.875 (73.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 12 2 3.875 (98.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
17 14 1 2.125 (54.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
18 14 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
19 14 2 2.875 (73.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 14 2 3.875 (98.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
21 16 1 2.125 (54.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
22 16 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
23 16 2 2.875 (73.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 16 2 3.875 (98.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
25 18 1 2.125 (54.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
26 18 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
27 18 1 2.125 (54.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
28 18 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
29 18 2 2.875 (73.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 18 2 3.875 (98.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
31 20 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
32 20 1 4.125 (104.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
33 20 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
34 20 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
35 20 2 3.875 (98.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 20 2 4.875 (123.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
37 20 2 3.875 (98.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
38 20 2 4.875 (123.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
39 22 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
40 22 1 4.125 (104.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 22 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
42 22 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
43 22 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
44 22 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
45 22 2 3.875 (98.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
46 22 2 4.875 (123.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
47 24 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 24 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49 24 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
50 24 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
51 24 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 24 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-33
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-33
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/11 and MS3437B
Straight Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued From Page B-32)
Dash
No. Shell
Size Style E
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
53 24 2 3.875 (98.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
54 24 2 4.875 (123.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
55 28 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
56 28 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
57 28 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58 28 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
59 28 1 3.125 (79.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
60 28 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
61 28 1 3.125 (79.4) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
62 28 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 32 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
64 32 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
65 32 1 3.125 (79.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 32 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
67 32 1 3.125 (79.4) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
68 32 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
69 32 1 3.125 (79.4) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
70 32 1 4.125 (104.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71 36 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
72 36 1 5.125 (130.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
73 36 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
74 36 1 5.125 (130.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
75 36 1 4.125 (104.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
76 36 1 5.125 (130.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
77 36 2 5.000 (127.0) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
78 36 2 6.000 (152.4) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
79 40 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
80 40 1 5.125 (130.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
81 40 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
82 40 1 5.125 (130.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
83 40 1 4.125 (104.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
84 40 1 5.125 (130.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
85 40 1 4.125 (104.8) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
86 40 1 5.125 (130.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
87 44 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
88 44 1 5.125 (130.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
89 44 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
90 44 1 5.125 (130.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
91 44 1 4.125 (104.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
92 44 1 5.125 (130.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
93 44 1 4.125 (104.8) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
94 44 1 5.125 (130.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
95 48 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
96 48 1 5.125 (130.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
97 48 1 4.125 (104.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
98 48 1 5.125 (130.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
99 48 1 4.125 (104.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
100 48 1 5.125 (130.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
101 48 1 4.125 (104.8) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
102 48 1 5.125 (130.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
103 61 1 3.125 (79.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
104 61 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
Continued on Page B-34
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-34
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/11 and MS3437B
Straight Environmental Backshell
TABLE II: Dash Number and Cable Range (Continued From Page B-33)
Dash
No. Shell
Size Style E
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
105 61 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
106 61 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
107 61 2 3.875 (98.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
108 61 2 4.875 (123.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
109 61 2 3.875 (98.4) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
110 61 2 4.875 (123.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
111 12 1 2.125 (54.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
112 16 1 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
113 16 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
114 12 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
115 12 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
116 14 1 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
117 14 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
118 16 1 2.125 (54.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
119 16 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
120 18 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
121 18 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
122 18 1 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
123 18 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
124 20 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
125 20 1 4.125 (104.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
126 22 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
127 22 1 4.125 (104.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
128 22 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
129 22 1 4.125 (104.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
130 24 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
131 24 1 4.125 (104.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
132 36 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
133 36 1 5.125 (130.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
134 40 1 4.125 (104.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
135 40 1 5.125 (130.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
136 10 1 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
137 10 1 3.125 (79.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
138 12 1 2.125 (54.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
139 12 1 3.125 (79.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
140 20 1 3.125 (79.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
141 20 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
142 22 1 3.125 (79.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
143 22 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
144 24 1 3.125 (79.4) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
145 24 1 4.125 (104.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
146 36 1 4.125 (104.8) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
147 36 1 5.125 (130.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
148 38 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
149 38 1 5.125 (130.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
150 14 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
151 14 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
152 16 1 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
153 16 1 3.125 (79.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
154 44 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
155 44 1 5.125 (130.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
156 40 1 4.125 (104.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
157 40 1 5.125 (130.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-35
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/14S
Self-Locking E-Nut
A Thread
C
.38
(9.7)
Max
.660
(16.8)
Max
Self-Locking
Coupling Nut
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN36455
TABLE I: Shell Size, Shell Size Code,
Thread and Dimensions
Shell
Size
Shell Size
Code Ref.
A Thread
Class 2B
Ø C
Max
9 AM12 X 1 - 6H .86 (21.8)
11 B M15 X 1 - 6H .98 (24.9)
13 CM18 X 1 - 6H 1.16 (29.5)
15 D 1M22 X 1 - 6H 1.28 (32.5)
17 E M25 X 1 - 6H 1.41 (35.8)
19 F M28 X 1 - 6H 1.52 (38.6)
21 G M31 X 1 - 6H 1.64 (41.7)
23 H M34 X 1 - 6H 1.77 (45.0)
25 J M37 X 1 - 6H 1.89 (48.0)
APPLICATION NOTES
1. For complete
dimensions, see the
applicable Military
Specication.
2. Metric dimensions
(mm) are indicated in
parentheses.
Basic Part
Number
M85049/14 -N11 W
Shell
Size
–– = Non Self-Locking
S = Detented
N = Non-Detented
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-36
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
A Thread
Typ.
E
Dia
M85049/16S =
.50 (12.7) Max
M85049/16G =
.69 (17.5) Max
MS3367-1
Tie Strap or
Equivalent
(Typical)
F
G
H
F
E
Dia
Ground Lug
Typical on
M85049/15G and
M85049/16G only
AS85049/15 and AS85049/16
45° and 90° Qwik-Ty® Strain Reliefs
Self-Locking Coupling • Optional Ground Lug
TABLE I: Shell Size, Thread, Cable Entry and Backshell Dimensions
Shell
Size
A Thread
Class 2B
E Dia
Max
F Max
Cable Entry
M85049/15S
G Max
M85049/15G
G Max
M85049/16
H Max
9 M12 X 1 - 6H .860 (21.8) .264 (6.7) 1.030 (26.2) 1.210 (30.7) 1.220 (31.0)
11 M15 X 1 - 6H .984 (25.0) .392 (10.0) 1.030 (26.2) 1.210 (30.7) 1.290 (32.8)
13 M18 X 1 - 6H 1.160 (29.5) .506 (12.9) 1.030 (26.2) 1.390 (35.3) 1.620 (41.1)
15 M22 X 1 - 6H 1.280 (32.5) .631 (16.0) 1.090 (27.7) 1.390 (35.3) 1.660 (42.2)
17 M25 X 1 - 6H 1.410 (35.8) .756 (19.2) 1.110 (28.2) 1.390 (35.3) 1.720 (43.7)
19 M28 X 1 - 6H 1.520 (38.6) .845 (21.5) 1.210 (30.7) 1.390 (35.3) 1.720 (43.7)
21 M31 X 1 - 6H 1.640 (41.7) .970 (24.6) 1.260 (32.0) 1.390 (35.3) 1.790 (45.5)
23 M34 X 1 - 6H 1.770 (45.0) 1.095 (27.8) 1.300 (33.0) 1.390 (35.3) 1.850 (47.0)
25 M37 X 1 - 6H 1.890 (48.0) 1.220 (31.0) 1.340 (34.0) 1.390 (35.3) 1.910 (48.5)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
4. Metric dimensions (mm) are in parentheses.
Basic Part Number
M85049/15 = 45°
M85049/16 = 90° M85049/15 G 11 N
Conguration
–– = Non-Self-Locking
N = Non-Detented
G = Self-Locking with Ground Lug
H = Non-Detented with Ground Lug
S = Self-Locking without Ground Lug Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
Shell Size
CONNECTOR DESIGNATOR:
HMIL-DTL-38999, Series III and IV
EN3645
SELF-LOCKING
COUPLING
Rev. 9.15.14
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-37
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/17
Straight EMI/RFI Environmental Backshell
TABLE II: Shell Size
and Clamp Size
Dash
No. Shell
Size
Series I
Shell
Size
Series II
Clamp Size
Min Max
08 09 08 01 02
10 11 10 01 03
12 13 12 02 04
14 15 14 02 05
16 17 16 02 06
18 19 18 03 07
20 21 20 03 08
22 23 22 03 09
24 25 24 04 10
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size, Cable Range and Dimensions
Clamp
Size Cable Range
Min Max E
Max F
Max
01 .062 (1.6) .125 (3.2) .781 (19.8) 1.250 (31.8)
02 .125 (3.2) .250 (6.4) .969 (24.6) 1.250 (31.8)
03 .250 (6.4) .375 (9.5) 1.062 (27.0) 1.250 (31.8)
04 .375 (9.5) .500 (12.7) 1.156 (29.4) 1.250 (31.8)
05 .500 (12.7) .625 (15.9) 1.250 (31.8) 1.312 (33.3)
06 .625 (15.9) .750 (19.1) 1.375 (34.9) 1.375 (34.9)
07 .750 (19.1) .875 (22.2) 1.500 (38.1) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.625 (41.3) 1.625 (41.3)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5) 1.625 (41.3)
10 1.125 (28.6) 1.250 (31.8) 1.875 (47.6) 1.625 (41.3)
TABLE IV: Length Code
Length
Code Available
Shell Sizes Length
Standard 08 - 24 1.500 (38.1)
A08 - 24 2.500 (63.5)
B14 - 24 3.500 (88.9)
C20 - 24 4.500 (114.3)
Basic
Part Number
M85049/17 10 N 03 A
Dash Number
(Table I)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
Length Code
(Table IV)
Omit for Standard
Clamp Size
(Table III)
TABLE I: Shell Size,
Thread and Dimensions
Dash
No. Shell
Size
Series I
Shell
Size
Series II
A Thread
Class 2B B Dia
Max
08 09 08 .438 - 28 UNEF .570 (14.5)
10 11 10 .562 - 24 UNEF .700 (17.8)
12 13 12 .688 - 24 UNEF .830 (21.1)
14 15 14 .813 - 20 UNEF .950 (24.1)
16 17 16 .938 - 20 UNEF 1.080 (27.4)
18 19 18 1.063 - 18 UNEF 1.200 (30.5)
20 21 20 1.188 - 18 UNEF 1.330 (33.8)
22 23 22 1.313 - 18 UNEF 1.450 (36.8)
24 25 24 1.438 - 18 UNEF 1.580 (40.1)
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-38
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/18
Straight EMI/RFI Environmental Backshell
TABLE I: Shell Size,
Thread and Dimensions
Shell
Size A Thread
Class 2B B Dia
Max
9 M12 X 1 - 6H .750 (19.1)
11 M15 X 1 - 6H .850 (21.6)
13 M18 X 1 - 6H 1.000 (25.4)
15 M22 X 1 - 6H 1.150 (29.2)
17 M25 X 1 - 6H 1.250 (31.8)
19 M28 X 1 - 6H 1.400 (35.6)
21 M31 X 1 - 6H 1.550 (39.4)
23 M34 X 1 - 6H 1.650 (41.9)
25 M37 X 1 - 6H 1.850 (47.0)
TABLE II:
Shell Size and
Clamp Size
Shell
Size Clamp Size
Min Max
9 01 02
11 01 03
13 02 04
15 02 05
17 02 06
19 03 07
21 03 08
23 03 09
25 04 10
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size, Cable Range and Dimensions
Clamp
Size Cable Range
Min Max E
Max F
Max
01 .062 (1.6) .125 (3.2) .781 (19.8) 1.250 (31.8)
02 .125 (3.2) .250 (6.4) .969 (24.6) 1.250 (31.8)
03 .250 (6.4) .375 (9.5) 1.062 (27.0) 1.250 (31.8)
04 .375 (9.5) .500 (12.7) 1.156 (29.4) 1.250 (31.8)
05 .500 (12.7) .625 (15.9) 1.250 (31.8) 1.312 (33.3)
06 .625 (15.9) .750 (19.1) 1.375 (34.9) 1.375 (34.9)
07 .750 (19.1) .875 (22.2) 1.500 (38.1) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.625 (41.3) 1.625 (41.3)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5) 1.625 (41.3)
10 1.125 (28.6) 1.250 (31.8) 1.875 (47.6) 1.625 (41.3)
TABLE IV: Length Code
Length
Code Available
Shell Sizes Length
Standard 9 - 25 1.500 (38.1)
A9 - 25 2.500 (63.5)
B9 - 25 3.500 (88.9)
C9 - 25 4.500 (114.3)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999, Series III and IV
EN3645
Basic
Part Number
M85049/18 11 N 03 A
Shell Size
(Table I)
Length Code
(Table IV)
Omit for Standard
Clamp Size
(Table III)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-39
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/19
Straight EMI/RFI Non-Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
Table III
Basic
Part Number
M85049/19 11 W 03 A
Shell Size
(Table I) Clamp Size
(Table II) Length
Code
(Omit for
Standard)
(Table III)
Finish
N = Electroless Nickel
W = Cadmium, Olive Drab
X = Nickel Fluorocarbon Polymer
Z = Zinc Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-40
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
TABLE I: Shell Size and Clamp Size
Shell
Size Clamp Size
Min Max A Thread
Class 6H C Dia
Max
9 01 02 M12 X 1 - 6H .750 (19.1)
11 01 03 M15 X 1 - 6H .850 (21.6)
13 02 04 M18 X 1 - 6H 1.000 (25.4)
15 02 05 M22 X 1 - 6H 1.100 (27.9)
17 02 06 M25 X 1 - 6H 1.250 (31.8)
19 03 07 M28 X 1 - 6H 1.400 (35.6)
21 03 08 M31 X 1 - 6H 1.500 (38.1)
23 03 09 M34 X 1 - 6H 1.650 (41.9)
25 04 10 M37 X 1 - 6H 1.700 (43.2)
TABLE II: Cable Range and Dimensions
Clamp
Size Cable Range
Min Max E
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .312 (7.9) .500 (12.7) 1.200 (30.5)
05 .437 (11.1) .625 (15.9) 1.250 (31.8)
06 .562 (14.3) .750 (19.1) 1.400 (35.6)
07 .687 (17.4) .875 (22.2) 1.500 (38.1)
08 .812 (20.6) 1.000 (25.4) 1.650 (41.9)
09 .937 (23.8) 1.125 (28.6) 1.750 (44.5)
10 1.062 (27.0) 1.250 (31.8) 1.900 (48.3)
TABLE III: Length Code
Length
Code Available
Shell Sizes Length
Std. 9 - 25 1.500 (38.1)
A9 - 25 2.500 (63.5)
B15 - 25 3.500 (88.9)
C21 - 25 4.500 (114.3)
AS85049/19
Straight EMI/RFI Non-Environmental Backshell
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-41
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/20
Straight Crimp Ring Backshell and Crimp Ring
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Entry is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE I: Shell Size, Thread, Cable Entry and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max E Dia
± .015 (0.4) F Dia
Max M85049/26-2
Crimp Ring Ref
9M12 X 1 - 6H .750 (19.1) .250 (6.4) .347 (8.8) 8
11 M15 X 1 - 6H .850 (21.6) .325 (8.3) .498 (12.6) 10
13 M18 X 1 - 6H 1.000 (25.4) .420 (10.7) .510 (13.0) 12
15 M22 X 1 - 6H 1.100 (27.9) .540 (13.7) .630 (16.0) 14
17 M25 X 1 - 6H 1.250 (31.8) .670 (17.0) .760 (19.3) 16
19 M28 X 1 - 6H 1.400 (35.6) .789 (20.0) .890 (22.6) 18
21 M31 X 1 - 6H 1.500 (38.1) .914 (23.2) 1.010 (25.7) 20
23 M34 X 1 - 6H 1.650 (41.9) 1.039 (26.4) 1.130 (28.7) 22
25 M37 X 1 - 6H 1.750 (44.5) 1.112 (28.2) 1.202 (30.5) 24
Basic
Part Number
M85049/20 -11 W
Shell Size
(Table I)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
Finish
N = Electroless Nickel
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-42
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/21
Straight Non-Environmental Strain Relief Backshell
APPLICATION
NOTES
1. For complete
dimensions see the
applicable Military
Specication.
2. Metric dimensions
(mm) are in
parentheses.
3. Cable Range is
dened as the
accommodation
range for the wire
bundle or cable.
Dimensions shown
are not intended for
inspection criteria.
Basic
Part Number
M85049/21 11 A 02 A
Shell
Size
Finish
A = Black Anodize
N = Electroless Nickel
W = Cadmium, Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel
Clamp
Size
Length Code
(Omit for Standard)
Table III
TABLE II: Clamp Size, Cable Range
and Dimensions
Clamp
Size Cable Range
Min Max E
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .312 (7.9) .500 (12.7) 1.200 (30.5)
05 .437 (11.1) .625 (15.9) 1.250 (31.8)
06 .562 (14.3) .750 (19.1) 1.400 (35.6)
07 .687 (17.4) .875 (22.2) 1.500 (38.1)
08 .812 (20.6) 1.000 (25.4) 1.650 (41.9)
09 .937 (23.8) 1.125 (28.6) 1.750 (44.5)
10 1.062 (27.0) 1.250 (31.8) 1.900 (48.3)
TABLE I: Shell Size, Clamp Size
and Dimensions
Shell
Size Clamp Size*
Min Max A Thread
Class 6H C Dia
Max
901 02 M12 X 1 - 6H .750 (19.1)
11 01 03 M15 X 1 - 6H .850 (21.6)
13 02 04 M18 X 1 - 6H 1.000 (25.4)
15 02 05 M22 X 1 - 6H 1.100 (27.9)
17 02 06 M25 X 1 - 6H 1.250 (31.8)
19 03 07 M28 X 1 - 6H 1.400 (35.6)
21 03 08 M31 X 1 - 6H 1.500 (38.1)
23 03 09 M34 X 1 - 6H 1.650 (41.9)
25 04 10 M37 X 1 - 6H 1.750 (44.5)
*Clamp Size from Table IV, AS85049/21 Specications.
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
TABLE III: Length
Code
Code Length
± .032 (0.8)
Standard 1.50 (38.1)
A2.50 (63.5)
B3.50 (88.9)
C4.50 (114.3)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-43
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/23 and MS3189C
45° EMI/RFI Non-Environmental Backshell
Basic
Part Number
M85049/23 -21 N
Dash Number
(Table II)
Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
Superseded
Part Number
MS3189C 21 N
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. When maximum cable entry is
exceeded, Style 2 will be supplied.
3. Metric dimensions (mm) are in
parentheses.
4. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE II: Dash Number, Cable Range and Dimensions
Dash
No. Shell
Size F
Max G
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
1 3 .687 (17.4) 1.915 (48.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
2 3 1.500 (38.1) 2.035 (51.7) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
3 8 .625 (15.9) 1.307 (33.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
4 10 .687 (17.4) 1.975 (50.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
5 10 .687 (17.4) 1.370 (34.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 6
6 12 .750 (19.1) 2.035 (51.7) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
7 12 .750 (19.1) 2.035 (51.7) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
8 12 .750 (19.1) 2.035 (51.7) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .812 (20.6) 2.125 (54.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
10 14 .812 (20.6) 1.780 (45.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 .906 (23.0) 2.235 (56.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 16 .906 (23.0) 1.875 (47.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.093 (27.8) 2.425 (61.6) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.093 (27.8) 2.062 (52.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.093 (27.8) 2.425 (61.6) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.093 (27.8) 2.062 (52.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.188 (30.2) 2.575 (65.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.188 (30.2) 2.218 (56.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.188 (30.2) 2.575 (65.4) 1.069 (27.2) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.188 (30.2) 2.218 (56.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.312 (33.3) 2.625 (66.7) 1.156 (33.7) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-44
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-44
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/23 and MS3189C
45° EMI/RFI Non-Environmental Backshell
* Denotes Style 2
TABLE II: Continued from Page B-43
Dash
No. Shell
Size F
Max G
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.312 (33.3) 2.281 (57.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.375 (34.9) 2.725 (69.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.375 (34.9) 2.725 (69.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.375 (34.9) 2.500 (63.5) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.406 (35.7) 2.815 (71.5) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.406 (35.7) 2.815 (71.5) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.406 (35.7) 2.469 (62.7) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.156 (54.8) 2.815 (71.5) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.156 (54.8) 2.815 (71.5) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.156 (54.8) 2.469 (62.7) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.156 (54.8) 2.815 (71.5) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.156 (54.8) 2.815 (71.5) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.156 (54.8) 2.469 (62.7) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.156 (54.8) 2.815 (71.5) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.156 (54.8) 2.815 (71.5) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.156 (54.8) 2.469 (62.7) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.188 (30.2) 2.575 (65.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.188 (30.2) 2.218 (56.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 .906 (23.0) 2.235 (56.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.093 (27.8) 2.425 (61.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
42 18 1.093 (27.8) 2.425 (61.6) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
43 20 1.093 (27.8) 2.425 (61.6) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
44 22 1.188 (30.2) 2.575 (65.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
45 22 1.188 (30.2) 2.575 (65.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
46 24 1.188 (30.2) 2.575 (65.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.406 (35.7) 2.815 (71.5) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 2.156 (54.8) 2.815 (71.5) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.500 (38.1) 2.035 (51.7) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
50* 14 1.842 (46.8) 2.425 (61.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 1.938 (49.2) 2.575 (65.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.093 (27.8) 2.425 (61.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.188 (30.2) 2.575 (65.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.093 (27.8) 2.425 (61.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.061 (52.3) 2.625 (66.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.188 (30.2) 2.575 (65.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.188 (30.2) 2.575 (65.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.061 (52.3) 2.625 (66.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.188 (30.2) 2.575 (65.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.312 (33.3) 2.625 (66.7) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.312 (33.3) 2.625 (66.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.375 (34.9) 2.725 (69.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.406 (35.7) 2.815 (71.5) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.406 (35.7) 2.815 (71.5) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.156 (54.8) 2.815 (71.5) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.156 (54.8) 2.815 (71.5) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
67 44 2.156 (54.8) 2.815 (71.5) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.156 (54.8) 2.815 (71.5) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.156 (54.8) 2.815 (71.5) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.156 (54.8) 2.815 (71.5) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.684 (42.8) 2.236 (56.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 1.938 (49.2) 2.575 (65.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.061 (52.3) 2.625 (66.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .812 (20.6) 2.125 (54.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
75 16 .906 (23.0) 2.235 (56.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-45
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/24 and MS3188C
90° EMI/RFI Non-Environmental Backshell
Basic
Part Number
M85049/24 -21 N
Dash Number
(Table II) Superseded
Part Number
MS3188C 21 N
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
Continued on Page B-46 • Refer to the Mil-Spec for Complete Dimensions
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602 Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
C
(Table I,
Page 38-10)
A Thread
(Table I,
Page 38-10)
TABLE II: Dash Number, Cable Range and Dimensions
Dash
No. Shell
Size H
Max J
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
1 03 .698 (17.7) 1.862 (47.3) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 04
2 03 1.448 (36.8) 1.382 (35.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 04
3 08 .603 (15.3) 1.262 (32.1) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 04
4 10 .698 (17.7) 1.982 (50.3) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
5 10 .698 (17.7) 1.382 (35.1) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 06
6 12 .703 (17.9) 2.002 (50.9) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
7 12 .703 (17.9) 2.002 (50.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
8 12 .703 (17.9) 1.397 (35.5) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
9 14 .803 (20.4) 2.072 (52.6) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
10 14 .803 (20.4) 1.717 (43.6) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
11 16 .988 (25.1) 2.162 (54.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
12 16 .988 (25.1) 1.807 (45.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
13 18 1.078 (27.4) 2.332 (59.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
14 18 1.078 (27.4) 1.982 (50.3) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .779 (19.8) 16
15 20 1.078 (27.4) 2.332 (59.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 20 1.079 (27.4) 1.982 (50.3) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
17 22 1.228 (31.2) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
18 22 1.228 (31.2) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
19 24 1.228 (31.2) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 24 1.228 (31.2) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
21 28 1.328 (33.7) 2.612 (66.3) 1.156 (33.7) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-46
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/24 and MS3188C
90° EMI/RFI Non-Environmental Backshell
TABLE II: Continued from Page B-45 • Refer to the Mil-DSpec for Complete Dimensions
Dash
No. Shell
Size H
Max K
Max K
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
22 28 1.328 (33.7) 2.257 (57.3) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
23 32 1.678 (42.6) 2.862 (72.7) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 32 1.678 (42.6) 2.862 (72.7) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
25 32 1.678 (42.6) 2.507 (63.7) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
26 36 1.878 (47.7) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
27 36 1.878 (47.7) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
28 36 1.878 (47.7) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
29 40 2.628 (66.8) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 40 2.628 (66.8) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
31 40 2.628 (66.8) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
32 44 2.628 (66.8) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
33 44 2.628 (66.8) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
34 44 2.628 (66.8) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
35 48 2.628 (66.8) 2.832 (71.9) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 48 2.628 (66.8) 2.832 (71.9) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
37 48 2.628 (66.8) 2.477 (62.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
38 61 1.228 (31.2) 2.442 (62.0) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
39 61 1.228 (31.2) 2.087 (53.0) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.184 (30.1) 20
40 16 .988 (25.1) 2.162 (54.9) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 18 1.078 (27.4) 2.332 (59.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
42 18 1.078 (27.4) 2.332 (59.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
43 20 1.078 (27.4) 2.332 (59.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
44 22 1.228 (31.2) 2.442 (62.0) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
45 22 1.228 (31.2) 2.442 (62.0) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
46 24 1.228 (31.2) 2.442 (62.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
47 36 1.878 (47.7) 2.832 (71.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 40 1.878 (47.7) 2.832 (71.9) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49* 10 1.453 (36.9) 2.002 (50.9) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
50* 14 1.828 (46.4) 2.334 (59.3) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
51* 16 1.978 (50.2) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 18 1.078 (27.4) 2.332 (59.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
53 61 1.228 (31.2) 2.087 (53.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
54 20 1.078 (27.4) 2.332 (59.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
55* 20 2.078 (52.8) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
56 22 1.228 (31.2) 2.442 (62.0) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
57 22 1.228 (31.2) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58* 22 2.078 (52.8) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
59 24 1.228 (31.2) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
60 28 1.328 (33.7) 2.612 (66.3) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
61 28 1.328 (33.7) 2.612 (66.3) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
62 32 1.678 (42.6) 2.862 (72.7) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 36 1.878 (47.7) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
64 36 1.878 (47.7) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
65 40 2.628 (66.8) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 40 2.628 (66.8) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 28
67 44 2.628 (66.8) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
68 44 2.628 (66.8) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
69 48 2.628 (66.8) 2.832 (71.9) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
70 48 2.628 (66.8) 2.832 (71.9) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71* 12 1.748 (44.4) 2.162 (54.9) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
72* 18 1.988 (50.5) 2.442 (62.0) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
73* 24 2.088 (53.0) 2.612 (66.3) 1.375 (34.9) 2.116 (53.7) .875 (22.2) 1.250 (31.8) 20
74 14 .803 (20.4) 2.072 (52.6) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
75 16 .988 (25.1) 2.162 (54.9) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-47
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/25 and MS3437C
Straight EMI/RFI Non-Environmental Backshell
Basic
Part Number
M85049/25 -21 N
Dash Number
(Table II) Superseded
Part Number
MS3188C 21 N
Basic
Part No. Dash
No.
Finish
(Material is Aluminum Only)
A = Cadmium Olive Drab over Nickel
C = Cadmium Olive Drab
N = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. When maximum cable entry is
exceeded, Style 2 will be supplied.
3. Metric dimensions (mm) are in
parentheses.
4. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3, EN 2997
EN 3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602 Finish / Material
B = Black Cadmium / Stainless Steel
N = Electroless Nickel / Aluminum
S = Passivated / Stainless Steel
W = 1,000 Hr. Cadmium Olive Drab
over Electroless Nickel / Aluminum
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
XS = Stainless Steel, Nickel Flurocarbon Polymer
ZS = Stainless Steel, Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-48
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
TABLE I: Shell Size
Dash
No. A Thread
Class 2B C Dia
Ref
03 .562 - 24 UNEF .77 (19.6)
08 .500 - 20 UNF .65 (16.5)
10 .625 - 24 UNEF .77 (19.6)
12 .750 - 20 UNEF .40 (10.2)
14 .875 - 20 UNEF 1.02 (25.9)
16 1.000 - 20 UNEF 1.21 (30.7)
18 1.062 - 18 UNEF 1.23 (31.2)
20 1.188 - 18 UNEF 1.36 (34.5)
22 1.313 - 18 UNEF 1.48 (37.6)
24 1.438 - 18 UNEF 1.73 (43.9)
28 1.750 - 18 UNS 1.97 (50.0)
32 2.000 - 18 UNS 2.22 (56.4)
36 2.250 - 16 UN 2.47 (62.7)
40 2.500 - 16 UN 2.72 (69.1)
44 2.750 - 16 UN 2.97 (75.4)
48 3.000 - 16 UN 3.22 (81.8)
61 1.500 - 18 UNEF 1.67 (42.4)
Refer to the
Mil-Spec
for
Complete
Dimensions
AS85049/25 and MS3437C
Straight EMI/RFI Non-Environmental Backshell
TABLE II: Dash Number, Dimensions and Cable Range
Dash
No. Shell
Size Style E
Max F
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
01 03 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
02 03 1 3.063 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
03 03 2 2.812 (71.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
04 03 2 3.812 (96.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
05 08 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
06 08 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .250 (6.4) 4
07 08 2 2.812 (71.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
08 08 2 3.812 (96.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
09 10 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
10 10 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 4
11 10 2 2.812 (71.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
12 10 2 3.812 (96.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
13 12 1 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
14 12 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 6
15 12 2 2.812 (71.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
16 12 2 3.812 (96.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
17 14 1 2.062 (52.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
18 14 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .575 (14.6) 10
19 14 2 2.812 (71.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
20 14 2 3.812 (96.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
21 16 1 2.062 (52.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
22 16 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .700 (17.8) 12
23 16 2 2.812 (71.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
24 16 2 3.812 (96.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
25 18 1 2.062 (52.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
26 18 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
27 18 1 2.062 (52.4) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
28 18 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
29 18 2 2.812 (71.4) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
30 18 2 3.812 (96.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
31 20 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
32 20 1 4.062 (103.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
33 20 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
34 20 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
35 20 2 3.812 (96.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
36 20 2 4.812 (122.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
37 20 2 3.812 (96.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
38 20 2 4.812 (122.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
39 22 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
40 22 1 4.062 (103.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
41 22 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
42 22 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
43 22 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
44 22 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
45 22 2 3.812 (96.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
46 22 2 4.812 (122.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
47 24 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
48 24 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
49 24 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
50 24 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .812 (20.6) 16
51 24 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
52 24 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
Continued on Page B-49
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-49
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Continued on Page B-50
AS85049/25 and MS3437C
Straight EMI/RFI Non-Environmental Backshell
TABLE II: Continued from Page B-48
Dash
No. Shell
Size Style E
Max F
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
53 24 2 3.812 (96.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
54 24 2 4.812 (122.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
55 28 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
56 28 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
57 28 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
58 28 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
59 28 1 3.062 (77.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
60 28 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
61 28 1 3.062 (77.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
62 28 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
63 32 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
64 32 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
65 32 1 3.062 (77.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
66 32 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
67 32 1 3.062 (77.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
68 32 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
69 32 1 3.062 (77.8) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
70 32 1 4.062 (103.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
71 36 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
72 36 1 5.062 (128.6) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
73 36 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
74 36 1 5.062 (128.6) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
75 36 1 4.062 (103.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
76 36 1 5.062 (128.6) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
77 36 2 4.942 (125.5) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
78 36 2 5.942 (150.9) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
79 40 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
80 40 1 5.062 (128.6) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
81 40 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
82 40 1 5.062 (128.6) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
83 40 1 4.062 (103.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
84 40 1 5.062 (128.6) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
85 40 1 4.062 (103.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
86 40 1 5.062 (128.6) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
87 44 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
88 44 1 5.062 (128.6) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
89 44 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
90 44 1 5.062 (128.6) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
91 44 1 4.062 (103.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
92 44 1 5.062 (128.6) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
93 44 1 4.062 (103.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
94 44 1 5.062 (128.6) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
95 48 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
96 48 1 5.062 (128.6) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
97 48 1 4.062 (103.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
98 48 1 5.062 (128.6) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
99 48 1 4.062 (103.2) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
100 48 1 5.062 (128.6) 1.781 (45.2) 2.770 (70.4) 1.250 (31.8) 1.625 (41.3) 28
101 48 1 4.062 (103.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
102 48 1 5.062 (128.6) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.875 (47.6) 32
103 61 1 3.062 (77.8) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
104 61 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-50
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/25 and MS3437C
Straight EMI/RFI Non-Environmental Backshell
TABLE II: Continued from Page B-49
Dash
No. Shell
Size Style E
Max F
Ref. L
Max Cable Range
Min Max M85049/42
Ref.
105 61 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
106 61 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
107 61 2 3.812 (96.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
108 61 2 4.812 (122.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.250 (31.8) 20
109 61 2 3.812 (96.8) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
110 61 2 4.812 (122.2) 1.500 (38.1) 2.363 (60.0) 1.000 (25.4) 1.375 (34.9) 24
111 12 1 2.062 (52.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
112 16 1 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
113 16 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
114 12 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
115 12 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
116 14 1 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
117 14 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
118 16 1 2.062 (52.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
119 16 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
120 18 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
121 18 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
122 18 1 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
123 18 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
124 20 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
125 20 1 4.062 (103.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
126 22 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
127 22 1 4.062 (103.2) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
128 22 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 0
129 22 1 4.062 (103.2) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .437 (11.1) 06
130 24 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
131 24 1 4.062 (103.2) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .625 (15.9) 10
132 36 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
133 36 1 5.062 (128.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
134 40 1 4.062 (103.2) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
135 40 1 5.062 (128.6) 1.059 (26.9) 1.551 (39.4) .500 (12.7) .750 (19.1) 12
136 10 1 2.062 (52.4) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 06
137 10 1 3.062 (77.8) 1.027 (26.1) 1.145 (29.1) .250 (6.4) .375 (9.5) 06
138 12 1 2.062 (52.4) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
139 12 1 3.062 (77.8) 1.027 (26.1) 1.332 (33.8) .350 (8.9) .500 (12.7) 10
140 20 1 3.062 (77.8) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
141 20 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .904 (23.0) 16
142 22 1 3.062 (77.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
143 22 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.029 (26.1) 20
144 24 1 3.062 (77.8) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
145 24 1 4.062 (103.2) 1.375 (34.9) 2.113 (53.7) .875 (22.2) 1.144 (29.1) 20
146 36 1 4.062 (103.2) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
147 36 1 5.062 (128.6) 1.830 (46.5) 3.020 (76.7) 1.437 (36.5) 1.840 (46.7) 32
148 36 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
149 36 1 5.062 (128.6) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
150 14 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
151 14 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
152 16 1 2.062 (52.4) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
153 16 1 3.062 (77.8) 1.027 (26.1) .957 (24.3) .125 (3.2) .312 (7.9) 04
154 44 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
155 44 1 5.062 (128.6) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
156 40 1 4.062 (103.2) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
157 40 1 5.062 (128.6) 1.156 (29.4) 1.770 (45.0) .625 (15.9) .937 (23.8) 16
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-51
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
M85049/26-2
Crimp Ring (See Page B-52)
AS85049/26-1 and MS3419
Straight Crimp Ring Backshell and Crimp Ring
Basic Part Number
M85049/26-1 = Adapter Only
M85049/26-2 = Crimp Ring Only
M85049/26-3 = Adapter with
Crimp Ring
(See Page B-52 for Crimp Ring)
M85049/26-1 -12 W
Shell Size
(Table II)
Superseded
Part Number
MS3419-21 C
Basic
Part No. Shell
Size
Finish
(Material is Aluminum Only)
A = Electroless Nickel
C = 500 Hr. Cadmium Olive Drab
over Electroless Nickel
TABLE I: Adapter Shell Size,Thread, and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max E
Dia F
Dia
3 .562 - 24 UNEF .670 (17.0) .250 (6.4) .337 (8.6)
8.500 - 20 UNF .620 (15.7) .250 (6.4) .337 (8.6)
10 .625 - 24 UNEF .730 (18.5) .325 (8.3) .488 (12.4)
12 .750 - 20 UNEF .860 (21.8) .420 (10.7) .500 (12.7)
14 .875 - 20 UNEF .980 (24.9) .540 (13.7) .620 (15.7)
16 1.000 - 20 UNEF 1.110 (28.2) .670 (17.0) .750 (19.1)
18 1.062 - 18 UNEF 1.220 (31.0) .789 (20.0) .880 (22.4)
20 1.188 - 18 UNEF 1.350 (34.3) .914 (23.2) 1.000 (25.4)
22 1.313 - 18 UNEF 1.470 (37.3) 1.039 (26.4) 1.120 (28.4)
24 1.438 - 18 UNEF 1.590 (40.4) 1.112 (28.2) 1.192 (30.3)
28 1.750 - 18 UNS 1.970 (50.0) 1.389 (35.3) 1.545 (39.2)
32 2.000 - 18 UNS 2.220 (56.4) 1.635 (41.5) 1.795 (45.6)
36 2.250 - 16 UN 2.470 (62.7) 1.850 (47.0) 2.045 (51.9)
40 2.500 - 16 UN 2.720 (69.1) 2.065 (52.5) 2.295 (58.3)
44 2.750 - 16 UN 2.970 (75.4) 2.320 (58.9) 2.545 (64.6)
48 3.000 - 16 UN 3.220 (81.8) 2.570 (65.3) 2.795 (71.0)
61 1.500 - 18 UNEF 1.650 (41.9) 1.210 (30.7) 1.359 (34.5)
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
See Page B-52 for
AS85049/26-2 Crimp Ring
CONNECTOR DESIGNATOR:
AAS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
Finish
N = Electroless Nickel
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-52
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/26-2
Backshell Crimp Ring
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. Crimp tool shall be the Thomas and Betts Installing Head catalog number 13640 or equivalent (see Table I).
3. The installing dies (Thomas and Betts Cat. No.--See Table I) shall be used with the Thomas and Betts Installing head Catalog Number
13640 or an equivalent tool.
4. Material/Finish: Copper/Tin Plate.
5. Metric dimensions (mm) are in parentheses.
TABLE I: Shell Size, Thread, Cable Entry and Dimensions
Dash
No.
Color
Code
A
Dia
Min Max
B
Dia
Min Max
L Dim
± ±.020 (0.5)
For Use with
AS85049/26-1
For Use with
AS85049/20
For Use with
AS85049/33-2
Installing
Die Cat. No.
(See Note 2)
8GREEN .400 (10.2) .410 (10.4) .448 (11.4) .458 (11.6) .250 (6.4) -3 & -8 -9 -8 GS405
10 RED .585 (14.9) .595 (15.1) .660 (16.8) .680 (17.3) .440 (11.2) -10 -11 -10 GS590
12 RED .585 (14.9) .595 (15.1) .660 (16.8) .680 (17.3) .440 (11.2) -12 -11 -10 GS590
14 BLUE .705 (17.9) .715 (18.2) .780 (19.8) .800 (20.3) .440 (11.2) -14 -15 -14 GS710
16 GREY .835 (21.2) .845 (21.5) .910 (23.1) .930 (23.6) .440 (11.2) -16 -17 -16 GS840
18 BROWN 1.005 (25.5) 1.015 (25.8) 1.080 (27.4) 1.100 (27.9) .440 (11.2) -18 -19 -18 GS1010
20 GREEN 1.125 (28.6) 1.135 (28.8) 1.200 (30.5) 1.220 (31.0) .440 (11.2) -20 -21 -20 GS1130
22 PINK 1.245 (31.6) 1.255 (31.9) 1.320 (33.5) 1.340 (34.0) .440 (11.2) -22 -23 -22 GS1250
24 ORANGE 1.327 (33.7) 1.337 (34.0) 1.402 (35.6) 1.422 (36.1) .440 (11.2) -24 -25 -24 GS1332
28 RED 1.665 (42.3) 1.675 (42.5) 1.740 (44.2) 1.760 (44.7) .440 (11.2) -28 GS1670
32 GREY 1.915 (48.6) 1.925 (48.9) 1.990 (50.5) 2.010 (51.4) .440 (11.2) -32 GS1920
36 GREEN 2.165 (55.0) 2.175 (55.2) 2.240 (56.9) 2.260 (57.4) .440 (11.2) -36 GS2170
40 ORANGE 2.415 (61.3) 2.425 (61.6) 2.490 (63.2) 2.510 (63.8) .440 (11.2) -40 GS2420
44 YELLOW 2.665 (67.7) 2.675 (67.9) 2.740 (69.6) 2.760 (70.1) .440 (11.2) -44 GS2670
48 BLUE 2.915 (74.0) 2.925 (74.3) 2.990 (75.9) 3.010 (76.5) .440 (11.2) -48 GS2920
61 PURPLE 1.435 (36.4) 1.445 (36.7) 1.510 (38.4) 1.530 (38.9) .440 (11.2) -61 GS1440
L
AB
Basic
Part Number
M85049/26 --2 -10
Dash No.
(Table I)
Product
Series
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-53
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/27 and M38999/1
Self-Locking and Non-Self-Locking E-Nut
A Thread
F
Self-Locking
G
Self-
Locking
E
CONNECTOR DESIGNATOR:
FMIL-DTL-27599, MIL-DTL-38999
Series I & II
TABLE I: Shell Size, Thread and Dimensions
Shell
Size
A Thread
Class 2B
Ø E
Max
Ø F
Max
G
Max
08 .438 - 28 UNEF .274 (7.0) .859 (21.8) .590 (15.0)
10 .562 - 24 UNEF .412 (10.5) .984 (25.0) .590 (15.0)
12 .688 - 24 UNEF .526 (13.4) 1.156 (29.4) .590 (15.0)
14 .813 - 20 UNEF .651 (16.5) 1.281 (32.5) .590 (15.0)
16 .938 - 20 UNEF .776 (19.7) 1.406 (35.7) .590 (15.0)
18 1.063 - 18 UNEF .882 (22.4) 1.516 (38.5) .590 (15.0)
20 1.188 - 18 UNEF 1.006 (25.6) 1.641 (41.7) .590 (15.0)
22 1.313 - 18 UNEF 1.132 (28.8) 1.766 (44.9) .590 (15.0)
24 1.438 - 18 UNEF 1.257 (31.9) 1.891 (48.0) .590 (15.0)
APPLICATION NOTES
1. For complete
dimensions, see the
applicable Military
Specication.
2. Metric dimensions
(mm) are indicated in
parentheses.
Basic Part
Number
M85049/27 N 10 W
Shell
Size
S = Self-Locking
N = Non-Detented
Use Dash for
Non-Self-Locking
Finish
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-54
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/28 and M83733/15
Straight Rectangular Non-Environmental Backshell
Basic
Part Number
M85049/28 -1
Dash Number
(Table II)
Superseded
Part Number
M83733/15 1
Basic
Part No.
Dash No.
(Table II)
#4-40 Unc X .437 Long Screw
With Lockwasher & Clearance
Hole For Screw Thru Metalastic
Gasket & Backshell
4 Each Required
.172 (4.4)
.121 (3.1)
Metalastic
Backshell Gasket
Metalastic
Entry Gasket
3.75 (95.3)
Ref
2.02 (51.3)
1.98 (50.3)
C
Monel Mesh
Connector Shell
Grounding Gasket
(See Note 3)
(See Note 3)
(See Note 3)
(See Note 1)
(See Note 1)
1. Assembly identied with manufacturer’s name and part number,
space permitting, location optional.
2. Glenair Series 600 Backshell Assembly Tools are recommended for
assembly and installation.
3. Gasket may be ordered as a kit (Glenair G61659), shell size A or B.
4. Dash numbers 1 and 3 = Standard cable entry.
Dash numbers 2 and 4 = Oversize cable entry.
5. Material/nish:
Backshell, adapter, clamp, ferrule - Al alloy/Electroless nickel.
Screws and washers -CRES/Passivate
Backshell and entry gaskets = Metalastic/N.A.
Interface gasket - Monel mesh/N.A.
6. Metric dimensions (mm) are indicated in parentheses
TABLE I:
Shell Size and Dimensions
Dash
No.
Shell
Size
A Max
Dim
B
Dim
C
Cable Range
(See Note 4)
1 A 2.126
(54.0)
1.900 (48.3)
1.890 (48.0)
.625 (15.9)
.500 (12.7)
2 A 2.126
(54.0)
1.900 (48.3)
1.890 (48.0)
.750 (19.1)
.625 (15.9)
3 B 3.426
(87.0)
3.200 (81.3)
3.190 (81.0)
.625 (15.9)
.500 (12.7)
4 B 3.426
(87.0)
3.200 (81.3)
3.190 (81.0)
.750 (19.1)
.625 (15.9)
)
.083 (2.1)
.815 (20.7)
.811 (20.6)
1.031 (26.2)
.969 (24.6)
.100 (2.5) Ref
.104 (2.6
B
A
APPLICATION NOTES
Rev. 10-17-14
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-55
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/29 (M38999/6)
Straight Non-Environmental Strain Relief Backshell
TABLE II: Clamp Size, Cable Range
and Dimensions
Clamp
Size Cable Range
Min Max E
Max
01 .062 (1.6) .125 (3.2) .781 (19.8)
02 .125 (3.2) .250 (6.4) .969 (24.6)
03 .250 (6.4) .375 (9.5) 1.062 (27.0)
04 .312 (7.9) .500 (12.7) 1.156 (29.4)
05 .437 (11.1) .625 (15.9) 1.250 (31.8)
06 .562 (14.3) .750 (19.1) 1.375 (34.9)
07 .687 (17.4) .875 (22.2) 1.500 (38.1)
08 .812 (20.6) 1.000 (25.4) 1.625 (41.3)
09 .937 (23.8) 1.125 (28.6) 1.750 (44.5)
10 1.062 (27.0) 1.250 (31.8) 1.875 (47.6)
Basic
Part Number
M85049/29 10 N 03 A
Shell
Size Clamp
Size
TABLE I: Shell Size and Clamp Size
Shell
Size Series I
Ref. Clamp Size*
Min Max A Thread
Class 2B
08 09 01 02 .438 - 28 UNEF
10 11 01 03 .562 - 24 UNEF
12 13 02 04 .688 - 24 UNEF
14 15 02 05 .813 - 20 UNEF
16 17 02 06 .938 - 20 UNEF
18 19 03 07 1.063 - 18 UNEF
20 21 03 08 1.188 - 18 UNEF
22 23 03 09 1.313 - 18 UNEF
24 25 04 10 1.438 - 18 UNEF
*Clamp Size from Table II, AS85049/29 Specications.
APPLICATION
NOTES
1. For complete
dimensions see the
applicable Military
Specication.
2. Metric dimensions
(mm) are in
parentheses.
3. Cable Range is
dened as the
accommodation
range for the wire
bundle or cable.
Dimensions shown
are not intended for
inspection criteria.
Finish
A = Black Anodize
N = Electroless Nickel
W = Cadmium, Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel
Length Code
(Omit for Standard)
Table III
TABLE III: Length
Code
Code Length
± .032 (0.8)
Standard 1.00 (25.4)
A2.00 (50.8)
B3.00 (76.2)
C4.00 (101.6)
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-56
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/30 and M38999/4
Straight TAG® Ring Backshell
Basic
Part Number
M85049/30 -10 W
Shell Size
(Table II) Superseded
Part Number
M38999/4 12 B
Basic
Part No. Shell
Size
Finish
(Material is Aluminum Only)
B = Cadmium Olive Drab over Nickel
F = Electroless Nickel
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Entry is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE I: Clamp Size, Cable Range and Dimensions
Shell
Size
Shell
Size
Series I
Ref
A
Thread
Class 2B
C
Dia
Max
E
Cable Entry
Max
F
Dia
Max
08 9 .438 - 28 UNEF .75 (19.1) .250 (6.4) .545 (13.8)
10 11 .562 - 24 UNEF .85 (21.6) .375 (9.5) .670 (17.0)
12 13 .688 - 24 UNEF 1.00 (25.4) .500 (12.7) .795 (20.2)
14 15 .813 - 20 UNEF 1.10 (27.9) .625 (15.9) .920 (23.4)
16 17 .938 - 20 UNEF 1.25 (31.8) .750 (19.1) 1.045 (26.5)
18 19 1.063 - 18 UNEF 1.40 (35.6) .844 (21.4) 1.170 (29.7)
20 21 1.188 - 18 UNEF 1.50 (38.1) .970 (24.6) 1.295 (32.9)
22 23 1.313 - 18 UNEF 1.65 (41.9) 1.094 (27.8) 1.420 (36.1)
24 25 1.438 - 18 UNEF 1.75 (44.5) 1.219 (31.0) 1.670 (42.4)
Finish
N = Electroless Nickel
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-57
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/31, MS3416 and MIL-DTL-85723/15N
Self-Locking and Non-Self-Locking E-Nut
A
Thread
G
F
Self-Locking
E
TABLE I: Shell Size, Thread and Dimensions
Shell
Size
A Thread
Class 2B
Ø E
Max
F
Max
Ø G
Max
3.562 - 24 UNEF .270 (6.9) -- --
8.500 - 20 UNF .270 (6.9) .710 (18.0) .885 (22.5)
10 .625 - 24 UNEF 375 (9.5) .710 (18.0) 1.010 (25.7)
12 .750 - 20 UNEF .511 (13.0) .710 (18.0) 1.135 (28.8)
14 .875 - 20 UNEF .585 (14.9) .710 (18.0) 1.260 (32.0)
16 1.000 - 20 UNEF .710 (18.0) .710 (18.0) 1.385 (35.2)
18 1.062 - 18 UNEF .789 (20.0) .710 (18.0) 1.510 (38.4)
20 1.188 - 18 UNEF .914 (23.2) .710 (18.0) 1.635 (41.5)
22 1.313 - 18 UNEF 1.039 (26.4) .710 (18.0) 1.760 (44.7)
24 1.438 - 18 UNEF 1.154 (29.3) .710 (18.0) 1.885 (47.9)
28 1.750 - 18 UNS 1.389 (35.3) .890 (22.6) 2.135 (54.2)
32 2.000 - 18 UNS 1.635 (41.5) .890 (22.6) 2.395 (60.8)
36 2.250 - 16 UN 1.850 (47.0) .890 (22.6) 2.635 (66.9)
40 2.500 - 16 UN 2.065 (52.5) .890 (22.6) 2.885 (73.3)
44 2.750 - 16 UN 2.320 (58.9) .890 (22.6) 3.135 (79.6)
48 3.000 - 16 UN 2.570 (65.3) .890 (22.6) 3.385 (86.0)
61 1.500 - 18 UNEF 1.194 (30.3) -- --
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
SAE AS81703 Crimp Series III,
MIL-DTL-83723 Series I,
MIL-DTL-83723 Series III
M83723/15N-10 A
Basic Part No.
(Non-Self-
Locking Only)
Superseded Part Number
Dash
No. Finish Designator
A = Non-Conductive, Black Anodize
R = Conductive, Electroless Nickel
MS3416 -10-E A
Superseded Part Number
Metal and Finish Designator
A = Aluminum 500 Hour Cad. Olive
Drab Over Electroless Nickel
C = Aluminum, Cadmium Olive Drab
G = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
Basic Part No.
(Non-Self-
Locking Only)
Dash No.
Style
APPLICATION NOTES
1. For complete dimensions, see the applicable
Military Specication.
2. Metric dimensions (mm) are indicated in
parentheses.
Basic Part
Number
M85049/31 S 22 W
Shell
Size
S = Self-Locking
N = Non-Detented
Use Dash for
Non-Self-Locking
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-58
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/33-2
Straight RFI/EMI Non-Environmental Backshell
TABLE I: Adapter Shell Size,Thread, Dimensions and Crimp Ring Ref.
Shell
Size A Thread
Class 2B C Dia
Max E
Dia F Dia
Max AS85049/26-2
Crimp Ring Ref
08 .438 - 28 UNEF .750 (19.1) .250 (6.4) .347 (8.8) 8
10 .562 - 24 UNEF .850 (21.6) .325 (8.3) .498 (12.6) 10
12 .688 - 24 UNEF 1.000 (25.4) .420 (10.7) .510 (13.0) 12
14 .813 - 20 UNEF 1.100 (27.9) .540 (13.7) .630 (16.0) 14
16 .938 - 20 UNEF 1.250 (31.8) .670 (17.0) .760 (19.3) 16
18 1.063 - 18 UNEF 1.400 (35.6) .789 (20.0) .890 (22.6) 18
20 1.188 - 18 UNEF 1.500 (38.1) .914 (23.2) 1.010 (25.7) 20
22 1.313 - 18 UNEF 1.650 (41.9) 1.039 (26.4) 1.130 (28.7) 22
24 1.438 - 18 UNEF 1.750 (44.5) 1.112 (28.2) 1.202 (30.5) 24
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
See Page B-52 for
AS85049/26-2 Crimp Ring
M85049/26-2 Crimp Ring
(See Table I and Page B-52)
Basic
Part Number
M85049/33-2 -10 W
Shell Size
(Table I)
Finish
N = Electroless Nickel
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
Z = Aluminum, Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-59
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/34
Straight Adapter and Extender
for Use with MS3114 and MS3124 Connectors
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
TABLE I: Shell Size and Dimensions
Shell
Size G Thread
UNEF Class 2A H Thread
UNEF Class 2A D
Dia E
Dia F
Max
8.4375 - 28 .625 - 24 .500 (12.7) .327 (8.3) .812 (20.6)
10 .5625 - 24 .750 - 20 .609 (15.5) .444 (11.3) .812 (20.6)
12 .6875 - 24 .875 - 20 .734 (18.6) .569 (14.5) .812 (20.6)
14 .8125 - 20 1.000 - 20 .859 (21.8) .673 (17.1) .812 (20.6)
16 .9375 - 20 1.125 - 18 .969 (24.6) .798 (20.3) .812 (20.6)
18 1.0625 - 18 1.250 - 18 1.109 (28.2) .915 (23.2) .812 (20.6)
20 1.1875 - 18 1.375 - 18 1.219 (31.0) 1.030 (26.2) .906 (23.0)
22 1.3125 - 18 1.500 - 18 1.344 (34.1) 1.155 (29.3) .906 (23.0)
24 1.4375 - 18 1.625 - 18 1.469 (37.3) 1.280 (32.5) .937 (23.8)
Basic
Part Number
M85049/34 -12 W
Shell Size
(Table I)
CONNECTOR DESIGNATOR:
DMIL-DTL-26482 Series I
For Use With
MS3114 and MS3124
Connectors Only
Finish
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-60
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/36 and M38999/7
Straight EMI/RFI Non-Environmental Backshell
Basic
Part Number
M85049/36 10 N 03 A
Shell Size
(Table I)
Finish
N = Electroless Nickel X = Nickel Fluorocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Zinc-Nickel, Black
over Electroless Nickel
Clamp Size
(Table I) Length
Code
(Omit for
Standard)
TABLE I: Shell Size and Clamp Size
Shell
Size Series I
Shell Size
Ref.
Clamp Size
(Table II)
Min Max
A Thread
Class 2B B Dia
Max
08 09 01 02 .438 - 28 UNEF .65 (16.5)
10 11 01 03 .562 - 24 UNEF .77 (19.6)
12 13 02 04 .688 - 24 UNEF .89 (22.6)
14 15 02 05 .813 - 20 UNEF 1.02 (25.9)
16 17 02 06 .938 - 20 UNEF 1.15 (29.2)
18 19 03 07 1.063 - 18 UNEF 1.23 (31.2)
20 21 03 08 1.188 - 18 UNEF 1.36 (34.5)
22 23 03 09 1.313 - 18 UNEF 1.48 (37.6)
24 25 04 10 1.438 - 18 UNEF 1.73 (43.9)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE II: Cable Range and Dimensions
Clamp
Size Cable Range
Min Max E
Max
01 .062 (1.6) .125 (3.2) .781 (19.8)
02 .125 (3.2) .250 (6.4) .969 (24.6)
03 .250 (6.4) .375 (9.5) 1.062 (27.0)
04 .312 (7.9) .500 (12.7) 1.156 (29.4)
05 .437 (11.1) .625 (15.9) 1.250 (31.8)
06 .562 (14.3) .750 (19.1) 1.375 (34.9)
07 .687 (17.4) .875 (22.2) 1.500 (38.1)
08 .812 (20.6) 1.000 (25.4) 1.625 (41.3)
09 .937 (23.8) 1.125 (28.6) 1.750 (44.5)
10 1.062 (27.0) 1.250 (31.8) 1.875 (47.6)
TABLE III: Length Code
Length
Code Available
Shell Sizes Length
Std. 08 - 24 1.500 (38.1)
A08 - 24 2.500 (63.5)
B14 - 24 3.500 (88.9)
C20 - 24 4.500 (114.3)
Table III
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-61
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049/37 and M38999/8
90° EMI/RFI Non-Environmental Backshell
TABLE I: Shell Size
Shell
Size
Series II
Series I
Shell Size
Ref.
A Thread
Class 2B
C Dia
Max
08 09 .438 - 28 UNEF .750 (19.1)
10 11 .562 - 24 UNEF .850 (21.6)
12 13 .688 - 24 UNEF 1.000 (25.4)
14 15 .813 - 20 UNEF 1.100 (27.9)
16 17 .938 - 20 UNEF 1.250 (31.8)
18 19 1.063 - 18 UNEF 1.400 (35.6)
20 21 1.188 - 18 UNEF 1.500 (38.1)
22 23 1.313 - 18 UNEF 1.650 (41.9)
24 25 1.438 - 18 UNEF 1.750 (44.5)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE II: Clamp Size and Dimensions
Shell
Size
Series II
Series I
Shell Size
Ref.
E
Max
F
Max
Clamp Size
Min Max
8 09 .720 (18.3) 2.50 (63.5) 01 02
10 11 .720 (18.3) 2.50 (63.5) 01 03
12 13 .800 (20.3) 2.56 (65.0) 02 04
14 15 .850 (21.6) 2.69 (68.3) 02 05
16 17 .910 (23.1) 2.81 (71.4) 02 06
18 19 1.000 (25.4) 3.03 (77.0) 03 06
20 21 1.050 (26.7) 3.19 (81.0) 03 07
22 23 1.100 (27.9) 3.31 (84.1) 03 08
24 25 1.200 (30.5) 3.31 (84.1) 04 09
Basic
Part Number
M85049/37 10 W 03 L
Shell Size
(Table I)
Clamp Size
(Table I)
D = 3 Drain Holes
L = Encapsulating
Hole
TABLE II: Clamp Size and Dimensions
Clamp
Size
Cable Range
Min Max
G
Max
01 .062 (1.6) .125 (3.2) .781 (19.8)
02 .125 (3.2) .250 (6.4) .969 (24.6)
03 .250 (6.4) .375 (9.5) 1.062 (27.0)
04 .312 (7.9) .500 (12.7) 1.156 (29.4)
05 .437 (11.1) .625 (15.9) 1.250 (31.8)
06 .562 (14.3) .750 (19.1) 1.375 (34.9)
07 .687 (17.4) .875 (22.2) 1.500 (38.1)
08 .812 (20.6) 1.000 (25.4) 1.625 (41.3)
09 .937 (23.8) 1.125 (28.6) 1.750 (44.5)
Finish
N = Electroless Nickel X = Nickel Fluorocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Zinc-Nickel, Black
over Electroless Nickel
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
Rev. 05.29.15
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-62
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/38
Straight Strain Relief
Self-Locking or Non-Self-Locking
A Thread
E
Self-Locking Only
F
Self-Locking
Only
H
Cable
Entry
Note: Screw orientation shown is for
non-self-locking configuration. Screws
on self-locking configurations are on
the same side/face of the clamp.
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN3645
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M85049/38 S 11 W
Shell Size
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = 300 Series Steel, Passivated
W = Aluminum, 500 Hour Cadmium
Olive Drab over Electroless Nickel
S = Self-Locking
Use Dash for Non-Self-Locking
N = Non-Detented
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size Shell Size
Ref. A Thread
Class 2B Ø E Max
Self-Locking Only F Max
Self-Locking Only H
Max Cable Entry
Min Max
9 A M12 X 1 - 6H .858 (21.8) .91 (23.1) .85 (21.6) .098 (2.5) .234 (5.9)
11 BM15 X 1 - 6H .984 (25.0) .91 (23.1) .90 (22.9) .153 (3.9) .234 (5.9)
13 C M18 X 1 - 6H 1.157 (29.4) 1.01 (25.7) 1.10 (27.9) .190 (4.8) .328 (8.3)
15 D M22 X 1 - 6H 1.279 (32.5) 1.06 (26.9) 1.15 (29.2) .260 (6.6) .457 (11.6)
17 E M25 X 1 - 6H 1.406 (35.7) 1.16 (29.5) 1.30 (33.0) .283 (7.2) .614 (15.6)
19 F M28 X 1 - 6H 1.516 (38.5) 1.41 (35.8) 1.50 (38.1) .325 (8.3) .634 (16.1)
21 G M31 X 1 - 6H 1.642 (41.7) 1.51 (38.4) 1.60 (40.6) .343 (8.7) .698 (17.7)
23 H M34 X 1 - 6H 1.768 (44.9) 1.66 (42.2) 1.70 (43.2) .381 (9.7) .823 (20.9)
25 J M37 X 1 - 6H 1.889 (48.0) 2.76 (44.7) 1.80 (45.7) .418 (10.6) .853 (21.7)
FOR NEW DESIGN
USE AS85049/124
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-63
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
AS85049/39
90° Strain Relief
Self-Locking or Non-Self-Locking
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size
Shell Size
Ref.
A Thread
Class 2B
Ø E Max
Self-Locking Only
F
Max
G
Max
H
Max
Cable Entry
Min Max
9 A M12 X 1 - 6H .858 (21.8) 1.01 (25.7) 1.00 (25.4) .85 (21.6) .098 (2.5) .234 (5.9)
11 BM15 X 1 - 6H .984 (25.0) 1.01 (25.7) 1.10 (27.9) .90 (22.9) .153 (3.9) .234 (5.9)
13 C M18 X 1 - 6H 1.157 (29.4) 1.21 (30.7) 1.10 (27.9) 1.10 (27.9) .190 (4.8) .328 (8.3)
15 D M22 X 1 - 6H 1.279 (32.5) 1.26 (32.0) 1.25 (31.8) 1.15 (29.2) .260 (6.6) .457 (11.6)
17 E M25 X 1 - 6H 1.406 (35.7) 1.41 (35.8) 1.30 (33.0) 1.30 (33.0) .283 (7.2) .614 (15.6)
19 F M28 X 1 - 6H 1.516 (38.5) 1.51 (38.4) 1.35 (34.3) 1.50 (38.1) .325 (8.3) .634 (16.1)
21 G M31 X 1 - 6H 1.642 (41.7) 1.66 (42.2) 1.60 (40.6) 1.60 (40.6) .343 (8.7) .698 (17.7)
23 H M34 X 1 - 6H 1.768 (44.9) 1.76 (44.7) 1.75 (44.5) 1.70 (43.2) .381 (9.7) .823 (20.9)
25 J M37 X 1 - 6H 1.889 (48.0) 2.91 (73.9) 1.85 (47.0) 1.80 (45.7) .418 (10.6) .853 (21.7)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M85049/39 S 11 W
Shell Size
S = Self-Locking
Use Dash for Non-Self-Locking
N = Non-Detented
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = 300 Series Steel, Passivated
W = Aluminum, 500 Hour Cadmium
Olive Drab over Electroless Nickel
FOR NEW DESIGN
USE AS85049/126
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN3645
A Thread
E
Self Locking
Only
F
Cable
Entry
G
H
G
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-64
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/41 and MS3057A
Straight Non-Self-Locking Strain Relief
for Use with MS “V” Thread General Duty “A” End Bell
A Thread
G
F
Cable
Entry
D
E
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. Conn. Shell
Ref.(s) A Thread
Class 2B Cable Entry
Max D
Ref. Ø E F G
±.031 (0.8) ±.031 (0.8) ±.031 (0.8)
3A 8S, 10S 1/2 - 28 UNEF .250 (6.4) .406 (10.3) .688 (17.5) .812 (20.6) .812 (20.6)
4A 10SL, 12S, 12 5/8 - 24 UNEF .312 (7.9) .406 (10.3) .812 (20.6) .875 (22.2) .812 (20.6)
6A 14S, 14 3/4 - 20 UNEF .438 (11.1) .406 (10.3) .969 (24.6) 1.062 (27.0) .875 (22.2)
8A 16S, 16 7/8 - 20 UNEF .562 (14.3) .406 (10.3) 1.094 (27.8) 1.156 (29.4) .938 (23.8)
10A 18 1 - 20 UNEF .625 (15.9) .406 (10.3) 1.188 (30.2) 1.250 (31.8) .938 (23.8)
12A 20, 22 1 3/16 - 18 UNEF .750 (19.1) .406 (10.3) 1.375 (34.9) 1.469 (37.3) .938 (23.8)
16A 24, 28 1 7/16 - 18 UNEF .938 (23.8) .406 (10.3) 1.656 (42.1) 1.688 (42.9) 1.031 (26.2)
20A 32 1 3/4 - 18 UNS 1.250 (31.8) .469 (11.9) 2.031 (51.6) 2.031 (51.6) 1.094 (27.8)
24A 36 2 - 18 UNS 1.375 (34.9) .531 (13.5) 2.219 (56.4) 2.281 (57.9) 1.156 (29.4)
28A 40 2 1/4 - 16 UN 1.625 (41.3) .531 (13.5) 2.500 (63.5) 2.688 (68.3) 1.688 (42.9)
32A 44 2 1/2 - 16 UN 1.875 (47.6) .594 (15.1) 2.781 (70.6) 2.938 (74.6) 1.750 (44.5)
40A 48 3 - 16 UN 2.375 (60.3) .656 (16.7) 3.281 (83.3) 3.500 (88.9) 1.750 (44.5)
Superseded
Part Number
MS3057-16A
Basic
Part No. Dash
No.
Basic
Part Number
M85049/41 -3A
Dash No.
APPLICATION NOTES
1. Finish on M85049/41 is Cadmium Olive Drab over Electroless Nickel, 1,000 hour salt spray.
2. Assembly to be identied with manufacturer’s name and part number, space permitting.
3. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
4. For complete dimensions, see the applicable Military Specication.
5. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-65
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/42 and MS3057D
Straight Non-Self-Locking Strain Relief
for Use with MS “V” Thread General Duty “A” End Bell
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. E Thread
Class 2B Ø F
Max Ø G H Cable Entry
±.020 (.5) ±.020 (.5) Max Min
4D 5/8 - 24 UNEF .937 (23.8) 1.281 (32.5) .937 (23.8) .312 (7.9) .125 (3.2)
6D 3/4 - 20 UNEF 1.031 (26.2) 1.281 (32.5) 1.125 (28.6) .437 (11.1) .250 (6.4)
8D 7/8 - 20 UNEF 1.250 (31.8) 1.281 (32.5) 1.312 (33.3) .562 (14.3) .312 (7.9)
10D 1 - 20 UNEF 1.250 (31.8) 1.281 (32.5) 1.312 (33.3) .625 (15.9) .350 (8.9)
12D 1 3/16 - 18 UNEF 1.437 (36.5) 1.312 (33.3) 1.531 (38.9) .750 (19.1) .500 (12.7)
16D 1 7/16 - 18 UNEF 1.688 (42.9) 1.406 (35.7) 1.750 (44.5) .937 (23.8) .625 (15.9)
20D 1 3/4 - 18 UNS 2.000 (50.8) 1.563 (39.7) 2.093 (53.2) 1.250 (31.8) .875 (22.2)
24D 2 - 18 UNS 2.250 (57.2) 1.625 (41.3) 2.343 (59.5) 1.375 (34.9) 1.000 (25.4)
28D 2 1/4 - 16 UN 2.500 (63.5) 1.900 (48.3) 2.750 (69.9) 1.625 (41.3) 1.250 (31.8)
32D 2 1/2 - 16 UN 2.750 (69.9) 1.900 (48.3) 3.000 (76.2) 1.875 (47.6) 1.437 (36.5)
MS3057 -10D A
Superseded Part Number
Metal and Finish Designator
A = Aluminum Cadmium Olive Drab over
Electroless Nickel
C = Aluminum, Cadmium Olive Drab
N = Aluminum, Electroless Nickel
D = 300 Series Steel, Cadmium Black Plate
S = 300 Series Steel, Passivate
Basic Part No. Dash
No.
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M85049/42 -10D W
Dash No.
Material/Finish
N = Aluminum/Electroless Nickel
W = Aluminum/1,000 Hour Cadmium over Electroless Nickel
X = Aluminum/Nickel Fluorocarbon Polymer
Y = Aluminum/Pure Dense Electrodeposited Aluminum
Z = Aluminum/Zinc Nickel Black
B = Stainless Steel/Cadmium Black
S = Stainless Steel/Passivated
XS = Stainless Steel/Nickel Fluorocarbon Polymer
YS = Stainless SteelPure Dense Electrodeposited Aluminum
ZS = Stainless Steel/Zinc Nickel Black
E
Thread
G
F
Telescoping Screws
Cable
Entry H
Stainless Steel
Clamp Saddle
Configuration
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-66
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/43 and MS3415
Strain Relief
45° Self-Locking or Non-Self-Locking
A Thread
C
F
Cable
Entry
E
CONNECTOR DESIGNATOR:
AAS5015 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
AS81703 Crimp Series III,
MIL-DTL-83723 Series I & III
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
5. Non-Self-Locking only.
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. A Thread
Class 2B C
Max E
Closed F
Max Cable Entry
Min Max
3* .562 - 24 UNEF .669 (17.0) 1.160 (29.5) .772 (19.6) .125 (3.2) .204 (5.2)
8.500 - 20 UNF .885 (22.5) 1.650 (29.5) .772 (19.6) .125 (3.2) .204 (5.2)
10 .625 - 24 UNEF 1.010 (25.7)) 1.694 (30.6) .803 (20.4) .187 (4.7) .286 (7.3)
12 .750 - 20 UNEF 1.135 (28.8) 1.768 (32.5) .866 (22.0) .291 (7.4) .416 (10.6)
14 .875 - 20 UNEF 1.260 (32.0) 1.840 (33.5) .928 (23.6) .351 (8.9) .476 (12.1)
16 1.000 - 20 UNEF 1.385 (35.2) 1.916 (36.2) .991 (25.2) .501 (12.7) .625 (15.9)
18 1.062 - 18 UNEF 1.570 (39.9) 2.034 (39.2) 1.110 (28.2) .518 (13.2) .706 (17.9)
20 1.188 - 18 UNEF 1.635 (41.5) 2.078 (40.3) 1.172 (29.8) .581 (14.8) .831 (21.1)
22 1.313 - 18 UNEF 1.760 (44.7) 2.122 (41.5) 1.235 (31.4) .644 (16.4) .956 (24.3)
24 1.438 - 18 UNEF 1.885 (47.9) 2.166 (42.6) 1.297 (32.9) .706 (17.9) 1.081 (27.5)
28 1.750 - 18 UNS 2.135 (54.2) 2.461 (45.7) 1.543 (39.2) .750 (19.1) 1.187 (30.1)
32 2.000 - 18 UNS 2.315 (58.8) 2.549 (48.0) 1.668 (42.4) .875 (22.2) 1.250 (31.8)
36 2.250 - 16 UN 2.635 (66.9) 2.595 (49.1) 1.793 (45.5) .938 (23.8) 1.375 (34.9)
40 2.500 - 16 UN 2.885 (73.3) 2.599 (49.1) 1.918 (48.7) .938 (23.8) 1.500 (38.1)
44 2.750 - 16 UN 3.135 (79.6) 2.860 (55.9) 2.132 (54.2) 1.188 (30.2) 1.750 (44.5)
48 3.000 - 16 UN 3.385 (86.0) 2.918 (58.1) 2.257 (57.3) 1.312 (33.3) 1.875 (47.6)
61* 1.500 - 18 UNEF 1.653 (41.5) 1.676 (42.6) 1.204 (30.6) .706 (17.9) 1.081 (27.5)
* See Note 5
Basic
Part Number
M85049/43 S 10 W
Dash No.
S = Self-Locking
Use Dash for Non-Self-Locking
N = Non-Detented
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-67
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/44 and M83733/16
Straight Non-Self-Locking Strain Relief
1.50 (38.1)
±.02 (0.5)
.25 (6.4)
±.02 (0.5)
Marking
Location
Optional
See Note 2
Ø.047 (1.2)
+.010 (0.3)
-.000 (0.0)
Wire Rope
Ø.080 (2.0)
+.012 (0.3)
-.000 (0.0)
PTFE Jacketed Coating
Ø.187/.178
(4.7/4.5)
E
.312 (7.9)
±.02 (0.5)
1.03 (26.2) Max
See Note 2 .818 (20.8) Max
C
A
B
D
Ø.116 (2.9) Hole
(4 Places)
.112-40 UNC-2A X .437 (11.1) Long
Screw With Lockwasher
(4 Places)
.062 (1.6) Thick
Silicone Cushion
Basic
Part Number
M85049/44 -3
Dash No.
APPLICATION NOTES
1. Assembly to be identied with
manufacturer’s name and part
number, space permitting.
2. Maximum dimension with halves
bottomed.
3. For complete dimensions, see the
applicable Military Specication.
4. Metric dimensions (mm) are in
parentheses.
5. Material/Finish:
Frame and saddles - Aluminum
alloy/Electroless nickel
Hardware - CRES/Passivated
Saddle cushion - Silicone/N/A
TABLE I: Dash Number, Shell Size and Dimensions
Dash
No. Shell
Size A Dim
± .062 (1.6) B Dim
± .005 (0.1) C Dim
± .032 (0.8) D Dim
± .062 (1.6) E Dim
± .062 (1.6) Lanyard
1 A 2.437 (61.9) 1.895 (48.1) .271 (6.9) 1.70 (43.2) N/A Without
2 B 3.750 (95.3) 3.195 (81.2) .277 (7.0) 3.00 (76.2) N/A
3 A 2.437 (61.9) 1.895 (48.1) .271 (6.9) 1.70 (43.2) 10.375 (263.5) With
4 B 3.750 (95.3) 3.195 (81.2) .277 (7.0) 3.00 (76.2) 10.375 (263.5)
Superseded
Part Number
M83733/16-16
Dash
No.
Basic
Part No.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-68
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/45 and MS27663-1
Straight Composite Non-Self-Locking Strain Relief
A Thread
C
FCable
Entry
E
Aluminum Nut Thermoplastic Body
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. Shell Size
Ref. A Thread
Class 2B Ø C
Max E
Max F
Max Cable Entry
Min Max
8 8/9 .438 - 28 UNEF .578 (14.7) 1.344 (34.1) .422 (10.7) .094 (2.4) .203 (5.2)
10 10/11 .562 - 24 UNEF .703 (17.9) 1.344 (34.1) .422 (10.7) .141 (3.6) .250 (6.4)
12 12/13 .688 - 24 UNEF .828 (21.0) 1.344 (34.1) .422 (10.7) .172 (4.4) .323 (8.2)
14 14/15 .813 - 20 UNEF .953 (24.2) 1.344 (34.1) .422 (10.7) .203 (5.2) .422 (10.7)
16 16/17 .938 - 20 UNEF 1.078 (27.4) 1.344 (34.1) .422 (10.7) .234 (5.9) .500 (12.7)
18 18/19 1.063 - 18 UNEF 1.203 (30.6) 1.344 (34.1) .422 (10.7) .265 (6.7) .562 (14.3)
20 20/21 1.188 - 18 UNEF 1.328 (33.7) 1.422 (36.1) .422 (10.7) .297 (7.5) .625 (15.9)
22 22/23 1.313 - 18 UNEF 1.453 (36.9) 1.422 (36.1) .422 (10.7) .328 (8.3) .703 (17.9)
24 24/25 1.438 - 18 UNEF 1.578 (40.1) 1.422 (36.1) .344 (8.7) .359 (9.1) .765 (19.4)
Basic
Part Number
M85049/45 W 10
Dash No. Superseded
Part Number
MS27663-1
Basic
Part No. Dash
No.
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Finish
A = Anodize, Black
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-69
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/46 and MS27663-2
90° Non-Self-Locking Composite Strain Relief
A Thread
C
F
Cable
Entry
E
Aluminum Nut
Thermoplastic Body
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. Shell Size
Ref. A Thread
Class 2B Ø C
Max E
Max F
Max Cable Entry
Min Max
8 8/9 .438 - 28 UNEF .578 (14.7) .656 (16.7) 1.015 (25.8) .094 (2.4) .203 (5.2)
10 10/11 .562 - 24 UNEF .703 (17.9) .688 (17.5) 1.062 (27.0) .141 (3.6) .250 (6.4)
12 12/13 .688 - 24 UNEF .828 (21.0) .750 (19.1) 1.125 (28.6) .172 (4.4) .323 (8.2)
14 14/15 .813 - 20 UNEF .953 (24.2) .859 (21.8) 1.328 (33.7) .203 (5.2) .422 (10.7)
16 16/17 .938 - 20 UNEF 1.078 (27.4) .937 (23.8) 1.392 (35.4) .234 (5.9) .500 (12.7)
18 18/19 1.063 - 18 UNEF 1.203 (30.6) 1.000 (25.4) 1.453 (36.9) .265 (6.7) .562 (14.3)
20 20/21 1.188 - 18 UNEF 1.328 (33.7) 1.062 (27.0) 1.609 (40.9) .297 (7.5) .625 (15.9)
22 22/23 1.313 - 18 UNEF 1.453 (36.9) 1.141 (29.0) 1.656 (42.1) .328 (8.3) .703 (17.9)
24 24/25 1.438 - 18 UNEF 1.578 (40.1) 1.203 (30.6) 1.719 (43.7) .359 (9.1) .765 (19.4)
Basic
Part Number
M85049/46 W 10
Dash No.
Superseded
Part Number
MS27663-2
Basic
Part No. Dash
No.
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Finish
A = Anodize, Black
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-70
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/47 and MS27507
90° Strain Relief
Self-Locking or Non-Self-Locking
A Thread F
H
Cable
Entry
G
E
Self-Locking
Only
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No.
Shell Size
Ref.
A Thread
Class 2B
Ø E
Max
F
Max
G
Max
H
Max
Cable Entry
Min Max
8 8/9 .438 - 28 UNEF .86 (21.8) 1.38 (35.1) 1.00 (25.4) .85 (21.6) .098 (2.5) .234 (5.9)
10 10/11 .562 - 24 UNEF .98 (24.9) 1.38 (35.1) 1.10 (27.9) .90 (22.9) .153 (3.9) .234 (5.9)
12 12/13 .688 - 24 UNEF 1.16 (29.5) 1.46 (37.1) 1.10 (27.9) 1.10 (27.9) .190 (4.8) .328 (8.3)
14 14/15 .813 - 20 UNEF 1.28 (32.5) 1.63 (41.4) 1.25 (31.8) 1.15 (29.2) .260 (6.6) .457 (11.6)
16 16/17 .938 - 20 UNEF 1.41 (35.8) 1.80 (45.7) 1.30 (33.0) 1.30 (33.0) .283 (7.2) .614 (15.6)
18 18/19 1.063 - 18 UNEF 1.52 (38.6) 1.82 (46.2) 1.35 (34.3) 1.50 (38.1) .325 (8.3) .634 (16.1)
20 20/21 1.188 - 18 UNEF 1.64 (41.7) 1.90 (48.3) 1.60 (40.6) 1.60 (40.6) .343 (8.7) .698 (17.7)
22 22/23 1.313 - 18 UNEF 1.77 (45.0) 2.04 (51.8) 1.75 (44.5) 1.70 (43.2) .381 (9.7) .823 (20.9)
24 24/25 1.438 - 18 UNEF 1.89 (48.0) 2.15 (54.6) 1.85 (47.0) 1.80 (45.7) .418 (10.6) .853 (21.7)
Basic
Part Number
M85049/47 S W 10
Dash No.
Material and Finish Designator
N = Aluminum, Electroless Nickel
S = 300 Series Steel, Passivated
W = Aluminum, 1000 Hour Cadmium
Olive Drab over Electroless Nickel
S = Self-Locking
Omit for Non-Self-Locking
N = Non-Detented, Self-Locking
MS27507-B 10
Superseded Part Number
Metal and Finish Designator
A = Aluminum Cadmium Olive Drab over Electroless Nickel
C = Aluminum, Cadmium Olive Drab
N = Aluminum, Electroless Nickel
D = 300 Series Steel, Cadmium Black Plate
S = 300 Series Steel, Passivate
Basic Part No.
(Non-Self-
Locking)
Dash No.
APPLICATION NOTES
1. Assembly to be identied with
manufacturer’s name and part
number, space permitting.
2. Cable Entry is dened as the
accommodation entry for the
wire bundle or cable.
3. Dimensions are not intended for
inspection criteria.
4. For complete dimensions, see the
applicable Military Specication.
5. Metric dimensions (mm) are in
parentheses.
FOR NEW DESIGN
USE AS85049/123
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
Rev. 10-23-14
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-71
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/48-1
Rectangular Backshells
MIL-DTL-24308
TABLE I: Dash Number and Backshell Dimensions
Dash
No. A
± .015 (0.4) C
± .005 (.13) E
± .015 (0.4) F
± .015 (0.4) G
± .015 (0.4) H
Max
1 1.203 (30.6) .984 (25.0) .375 (9.5) .375 (9.5) .750 (19.1) 1.250 (31.8)
2 1.531 (38.9) 1.312 (33.3) .713 (18.1) .312 (7.9) .750 (19.1) 1.250 (31.8)
3 2.078 (52.8) 1.852 (47.0) 1.000 (25.4) .312 (7.9) 1.000 (25.4) 1.563 (39.7)
4 2.718 (69.0) 2.500 (63.5) 1.375 (34.9) .312 (7.9) 1.000 (25.4) 1.563 (39.7)
5 2.625 (66.7) 2.406 (61.1) 1.406 (35.7) .406 (10.3) 1.125 (28.6) 1.688 (42.9)
APPLICATION NOTES
1. Assembly identied with manufacturer’s
name and part number, space
permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
Basic
Part Number
M85049/48 -1-3 F
Dash
Number
Finish
F = Yellow Chromate
over Cadmium
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-72
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/48-2
Rectangular Backshells
MIL-DTL-24308
TABLE I: Dash Number and Backshell Dimensions
Dash
No.
Nonmagnetic
(Brass)
A
± .015 (0.4)
C
± .005 (.13) DE
± .015 (0.4)
G
± .030 (0.8)
H
± .015 (0.4)
1 6 1.208 (30.7) .984 (25.0) .406 (10.3) .661 (16.8) 1.031 (26.2) .344 (8.7)
2 7 1.531 (38.9) 1.312 (33.3) .406 (10.3) .984 (25.0) 1.031 (26.2) .344 (8.7)
3 8 2.078 (52.8) 1.852 (47.0) .593 (15.1) 1.515 (38.5) 1.062 (27.0) .344 (8.7)
4 9 2.718 (69.0) 2.500 (63.5) .718 (18.2) 2.171 (55.1) 1.062 (27.0) .344 (8.7)
5 10 2.625 (66.7) 2.406 (61.1) .812 (20.6) 2.093 (53.2) 1.062 (27.0) .438 (11.1)
APPLICATION NOTES
1. Assembly identied with manufacturer’s
name and part number, space
permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
Basic
Part Number
M85049/48 -2-3 F
Dash
Number
Finish
F = Yellow Chromate
over Cadmium
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-73
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/48-3
Rectangular Backshell
MIL-DTL-24308
TABLE I: Dash Number and Backshell Dimensions
Dash
No. No. of
Screws A
± .015 (0.4) B
± .015 (0.4) C
± .005 (0.1) F
Max G
± .015 (0.4) H
± .015 (0.4)
2 2 1.531 (38.9) .500 (12.7) 1.312 (33.3) .679 (17.2) 1.091 (27.7) .442 (11.2)
3 2 2.078 (52.8) .500 (12.7) 1.852 (47.0) .679 (17.2) 1.631 (41.4) .442 (11.2)
4 3 2.718 (69.0) .500 (12.7) 2.500 (63.5) .679 (17.2) 2.282 (58.0) .442 (11.2)
5 3 2.625 (66.7) .609 (15.5) 2.406 (61.1) .724 (18.4) 2.205 (56.0) .565 (14.4)
APPLICATION NOTES
1. Assembly identied with
manufacturer’s name and part
number, space permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
Basic
Part Number
M85049/48 -3-3 F
Dash
Number
Finish
F = Yellow Chromate
over Cadmium
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-74
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/49-2 and MS27506
Straight Strain Relief
Self-Locking or Non-Self-Locking
A Thread
E
Self-Locking Only
F
Self-Locking
Only
H
Cable
Entry
Note: Screw
orientation shown is
for non-self-locking
configuration. Screws
on self-locking
configurations are on
the same side/face of
the clamp.
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size Shell Size
Ref. A Thread
Class 2B Ø E Max
Self-Locking Only F Max
Self-Locking Only H
Max Cable Entry
Min Max
8 8/9 .438 - 28 UNEF .86 (21.8) .91 (23.1) .85 (21.6) .098 (2.5) .234 (5.9)
10 10/11 .562 - 24 UNEF .98 (24.9) .91 (23.1) .90 (22.9) .153 (3.9) .234 (5.9)
12 12/13 .688 - 24 UNEF 1.16 (29.5) 1.01 (25.7) 1.10 (27.9) .190 (4.8) .328 (8.3)
14 14/15 .813 - 20 UNEF 1.28 (32.5) 1.06 (26.9) 1.15 (29.2) .260 (6.6) .457 (11.6)
16 16/17 .938 - 20 UNEF 1.41 (35.8) 1.16 (29.5) 1.30 (33.0) .283 (7.2) .614 (15.6)
18 18/19 1.063 - 18 UNEF 1.52 (38.6) 1.41 (35.8) 1.50 (38.1) .325 (8.3) .634 (16.1)
20 20/21 1.188 - 18 UNEF 1.64 (41.7) 1.51 (38.4) 1.60 (40.6) .343 (8.7) .698 (17.7)
22 22/23 1.313 - 18 UNEF 1.77 (45.0) 1.66 (42.2) 1.70 (43.2) .381 (9.7) .823 (20.9)
24 24/25 1.438 - 18 UNEF 1.89 (48.0) 1.76 (44.7) 1.80 (45.7) .418 (10.6) .853 (21.7)
CONNECTOR DESIGNATOR:
FMIL-DTL-27599,
MIL-DTL-38999 Series I & II
Basic
Part Number
M85049/49-2 S 10 W
Dash No.
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = 300 Series Steel, Passivated
W = Aluminum, 1000 Hour Cadmium
Olive Drab over Electroless Nickel
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
S = Self-Locking
Use Dash for Non-Self-Locking
N = Non-Detented
FOR NEW DESIGN
USE AS85049/121
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-75
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/50
Rectangular Backshell
MIL-DTL-24308
TABLE I: Dash Number and Backshell Dimensions
Dash
No. A
± .015 (0.4) B
± .030 (0.8) C
± .005 (0.1) D
Max E
.030 (0.8)
11.203 (30.6) .718 (18.2) .984 (25.0) .467 (11.9) .437 (11.1)
2 1.531 (38.9) .718 (18.2) 1.312 (33.3) .467 (11.9) .437 (11.1)
3 2.078 (52.8) .968 (24.6) 1.852 (47.0) .467 (11.9) .625 (15.9)
4 2.718 (69.0) 1.187 (30.1) 2.500 (63.5) .467 (11.9) .812 (20.6)
5 2.625 (66.7) 1.250 (31.8) 2.406 (61.1) .592 (15.0) .906 (23.0)
APPLICATION NOTES
1. Assembly identied with manufacturer’s
name and part number, space
permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
Basic
Part Number
M85049/50 -3-F
Dash
Number
Finish
F = Yellow Chromate
over Cadmium
B
AD
Cable
Clamp
C
E
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-76
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/51 and MS3418
90° Strain Relief
Self-Locking or Non-Self-Locking
A Thread
E
Self Locking
Only
F
Self Locking
Only
H
Cable
Entry
G
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
SAE-AS1703 Crimp Series III,
MIL-DTL-83723 Series I & III
Basic
Part Number
M85049/51 S 10 W
Dash No.
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = Stainless Steel, Passivate
W = Aluminum, 1000 Hr. Cadmium O.D.
over Electroless Nickel
S = Self-Locking
-1 = Non-Self-Locking
N = Non-Detented
MS3418-10 C
Superseded Part Number
Metal and Finish Designator
A = Aluminum 1000 Hour Cadmium Olive
Drab over Electroless Nickel
C = Aluminum, Cadmium Olive Drab
G = Aluminim Black Anodize
N = Aluminum, Electroless Nickel
Basic
Part No.
(Non-Self-
Locking)
Dash
No.
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No.
A Thread
Class 2B
Ø E Max
Self-Locking
F Max
Self-Locking
GH
Max
Cable Entry
±.062 (1.6) Min Max
3*+ .562 - 24 UNEF - - - - .777 (19.7) .782 (19.9) .125 (3.2) .204 (5.2)
8.500 - 20 UNF .885 (22.5) 1.257 (31.9) .746 (18.9) .782 (19.9) .125 (3.2) .204 (5.2)
10 .625 - 24 UNEF 1.010 (25.7) 1.339 (34.0) .805 (20.4) .862 (21.9) .187 (4.7) .286 (7.3)
12 .750 - 20 UNEF 1.135 (28.8) 1.532 (38.9) .867 (22.0) 1.003 (25.5) .291 (7.4) .416 (10.6)
14 .875 - 20 UNEF 1.260 (32.0) 1.592 (40.4) .930 (23.6) 1.061 (26.9) .351 (8.9) .476 (12.1)
16 1.000 - 20 UNEF 1.385 (35.2) 1.741 (44.2) .994 (25.2) 1.334 (33.9) .501 (12.7) .626 (15.9)
18 1.062 - 18 UNEF 1.510 (38.4) 1.853 (47.1) 1.171 (29.7) 1.466 (37.2) .518 (13.2) .706 (17.9)
20 1.188 - 18 UNEF 1.635 (41.5) 1.978 (50.2) 1.234 (31.2) 1.572 (39.9) 581 (14.8) .831 (21.1)
22 1.313 - 18 UNEF 1.760 (44.7) 2.108 (53.5) 1.296 (32.9) 1.688 (42.9) .644 (16.4) .956 (24.3)
24 1.438 - 18 UNEF 1.885 (47.9) 2.228 (56.6) 1.358 (34.5) 1.790 (45.5) .706 (17.9) 1.081 (27.5)
28+ 1.750 - 18 UNS 2.135 (54.2) 2.528 (64.2) 1.572 (39.9) 2.035 (51.7) .750 (19.1) 1.187 (30.1)
32+ 2.000 - 18 UNS 2.395 (60.8) 2.591 (65.8) 1.797 (45.6) 2.386 (60.6) .875 (22.2) 1.250 (31.8)
36+ 2.250 - 16 UN 2.635 (66.9) 2.716 (69.0) 1.922 (48.8) 2.496 (63.4) .938 (23.8) 1.375 (34.9)
40+ 2.500 - 16 UN 2.885 (73.3) 2.841 (72.2) 2.047 (52.0) 2.566 (65.2) .938 (23.8) 1.500 (38.1)
44+ 2.750 - 16 UN 3.135 (79.6) 3.091 (78.5) 2.296 (58.3) 2.860 (72.6) 1.188 (30.2) 1.750 (44.5)
48+ 3.000 - 16 UN 3.385 (86.0) 3.216 (81.7) 2.421 (61.5) 3.344 (84.9) 1.312 (33.3) 1.875 (47.6)
61*+ 1.500 - 18 UNEF - - - - 1.388 (35.3) 1.775 (45.1) .706 (17.9) 1.081 (27.5)
* Not Available in Self Locking + Not Available under M83723/15A
APPLICATION NOTES
1. Assembly to be identied with
manufacturer’s name and part
number, space permitting.
2. Cable Entry is dened as the
accommodation entry for the
wire bundle or cable.
3. Dimensions are not intended for
inspection criteria.
4. For complete dimensions, see the
applicable Military Specication.
5. Metric dimensions (mm) are in
parentheses.
FOR NEW DESIGN
USE AS85049/120
Rev. 04.28.16
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-77
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/52 and MS3417
Straight Strain Relief
Self-Locking or Non-Self-Locking
A Thread
E Dia
Self Locking
Only
F
Self Locking
Only
Cable
Entry
G
CONNECTOR DESIGNATOR:
AAS50151 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
SAE-AS1703 Crimp Series III,
MIL-DTL-83723 Series I & III
Basic
Part Number
M85049/52 S 10 W
Dash No.
MS3417-10 A
Superseded Part Number
Metal and Finish Designator
A = Aluminum 1000 Hour Cadmium Olive
Drab over Electroless Nickel
C = Aluminum, Cadmium Olive Drab
G = Aluminim Black Anodize
N = Aluminum, Electroless Nickel
Basic
Part No.
(Non-Self-
Locking)
Dash
No.
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Dash
No. A Thread
Class 2B Ø E Max
Self-Locking F Max
Self-Locking G
Max Cable Entry
Min Max
3*+ .562 - 24 UNEF - - - - .782 (19.9) .125 (3.2) .204 (5.2)
8.500 - 20 UNF .885 (22.5) .73 (18.5) .782 (19.9) .125 (3.2) .204 (5.2)
10 .625 - 24 UNEF 1.010 (25.7) .85 (21.6) .862 (21.9) .187 (4.7) .286 (7.3)
12 .750 - 20 UNEF 1.135 (28.8) .98 (24.9) 1.003 (24.6) .291 (7.4) .416 (10.6)
14 .875 - 20 UNEF 1.260 (32.0) .98 (24.9) 1.061 (25.5) .351 (8.9) .476 (12.1)
16 1.000 - 20 UNEF 1.385 (35.2) 1.10 (27.9) 1.234 (26.9) .501 (12.7) .626 (15.9)
18 1.062 - 18 UNEF 1.510 (38.4) 1.35 (34.3) 1.466 (35.4) .518 (13.2) .706 (17.9)
20 1.188 - 18 UNEF 1.635 (41.5) 1.98 (50.3) 1.572 (37.2) 581 (14.8) .831 (21.1)
22 1.313 - 18 UNEF 1.760 (44.7) 2.73 (69.3) 1.688 (39.9) .644 (16.4) .956 (24.3)
24 1.438 - 18 UNEF 1.885 (47.9) 2.88 (73.2) 1.790 (43.1) .706 (17.9) 1.081 (27.5)
28+ 1.750 - 18 UNS 2.135 (54.2) 2.528 (64.2) 2.035 (45.5) .750 (19.1) 1.187 (30.1)
32+ 2.000 - 18 UNS 2.395 (60.8) 2.591 (65.8) 2.386 (51.7) .875 (22.2) 1.250 (31.8)
36+ 2.250 - 16 UN 2.635 (66.9) 2.13 (54.1) 2.446 (60.6) .938 (23.8) 1.375 (34.9)
40+ 2.500 - 16 UN 2.885 (73.3) 2.44 (62.0) 2.566 (65.2) .938 (23.8) 1.500 (38.1)
44+ 2.750 - 16 UN 3.135 (79.6) 3.00 (76.2) 2.860 (72.6) 1.188 (30.2) 1.750 (44.5)
48+ 3.000 - 16 UN 3.385 (86.0) 3.40 (86.4) 3.344 (84.9) 1.312 (33.3) 1.875 (47.6)
61*+ 1.500 - 18 UNEF - - - - 1.775 (45.1) .706 (17.9) 1.081 (27.5)
* Not Available in Self Locking + Not Available under M83723/15S
APPLICATION NOTES
1. Assembly to be identied with
manufacturer’s name and part
number, space permitting.
2. Cable Entry is dened as the
accommodation entry for the
wire bundle or cable.
3. Dimensions are not intended for
inspection criteria.
4. For complete dimensions, see the
applicable Military Specication.
5. Metric dimensions (mm) are in
parentheses.
S = Self-Locking
-1 = Non-Self-Locking
N = Non-Detented
FOR NEW DESIGN
USE AS85049/1 18
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = Stainless Steel, Passivate
W = Aluminum, 1000 Hr. Cadmium O.D.
over Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-78
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/53, AS85049/54 and AS85049/55
Straight, 45° and 90° Qwik-Ty Strain Reliefs
Optional Self-Locking • Optional Ground Lug
TABLE I: Shell Size, Thread, Cable Entry and Backshell Dimensions
Shell
Size
A Thread
Class 2B
C Dia
Max
E Dia
Max
F
Cable Entry
G
Max
H
Max
J
Max
K
Max
03 562 - 24 UNEF .780 (19.8) 1.010 (25.7) .260 (6.6) .954 (24.0) 1.232 (31.3) .730 (18.5) 1.290 (32.8)
08 .500 - 20 UNF .660 (16.8) .890 (22.6) .260 (6.6) .954 (24.0) 1.232 (31.3) .730 (18.5) 1.290 (31.0)
10 .625 - 24 UNEF .780 (19.8) 1.010 (25.7) .365 (9.3) .954 (24.0) 1.232 (31.3) .730 (18.5) 1.290 (32.8)
12 .750 - 20 UNEF .940 (23.9) 1.140 (29.0) .501 (12.7) .954 (24.0) 1.232 (31.3) .730 (18.5) 1.620 (41.1)
14 .875 - 20 UNEF 1.050 (26.7) 1.260 (32.0) .575 (14.6) 1.204 (30.6) 1.232 (31.3) .730 (18.5) 1.660 (42.2)
16 1.000 - 20 UNEF 1.240 (31.5) 1.390 (35.3) .700 (17.8) 1.204 (30.6) 1.232 (31.3) .730 (18.5) 1.720 (43.7)
18 1.062 - 18 UNEF 1.380 (35.1) 1.510 (38.4) .779 (19.8) 1.204 (30.6) 1.232 (31.3) .730 (18.5) 1.720 (43.7)
20 1.188 - 18 UNEF 1.500 (38.1) 1.640 (41.7) .904 (23.0) 1.310 (33.3) 1.482 (37.6) .750 (19.1) 1.790 (45.5)
22 1.313 - 18 UNEF 1.630 (41.4) 1.760 (44.7) 1.029 (26.1) 1.430 (36.3) 1.482 (37.6) .750 (19.1) 1.850 (47.0)
24 1.438 - 18 UNEF 1.750 (44.5) 1.890 (48.0) 1.144 (29.1) 1.560 (39.6) 1.482 (37.6) .750 (19.1) 1.910 (48.5)
28 1.750 - 18 UNS 1.970 (50.0) 2.140 (54.4) 1.379 (35.0) 1.560 (39.6) 1.469 (37.3) .750 (19.1) 2.060 (52.3)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
4. Metric dimensions (mm) are in parentheses.
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I and III
40M39569, DEF 5326-3, EN2997
EN3646, ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
OPTIONAL
SELF-LOCKING
COUPLING
FOR NEW DESIGN APPLICATIONS USE
M85049/43 (45°), M85049/51 (90°) and M85049/52 (Straight)
M85049/55 G 22 N
Conguration
–– = Non-Self-Locking
G = Non-Self-Locking with Ground Lug*
S = Detented, Self-Locking*
T = Detented, Self-Locking with Ground Lug
N = Non-Detented, Self-Locking
H = Non-Detented, Self-Locking with Ground Lug
*Conguration Options G, S, T, H and N are
only available with AS85049/55
Shell
Size
Basic Part Number
M85049/53 = Straight
M85049/54 = 45°
M85049/55 = 90°
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited
Aluminum
Z = Zinc-Nickel, Black
Rev. 03/15/18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-79
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/56 and AS85049/57
Straight and 45° Qwik-Ty Strain Reliefs
Optional Self-Locking • Optional Ground Lug
TABLE I: Shell Size, Thread, Cable Entry and Backshell Dimensions
Shell
Size
Series II
Series I
Shell Size
Ref.
A Thread
Class 2B
C Dia
Max
E Dia
Max
F
Cable Entry
G
Max
H
Max
8 9 .438-28 UNEF .750 (19.1) .860 (21.8) .264 (6.7) .895 (22.7) 1.210 (30.7)
10 11 .562-24 UNEF .850 (21.6) .980 (24.9) .392 (10.0) .895 (22.7) 1.210 (30.7)
12 13 .688-24 UNEF 1.000 (25.4) 1.160 (29.5) .506 (12.9) .955 (24.3) 1.390 (35.3)
14 15 .813-20 UNEF 1.100 (27.9) 1.280 (32.5) .631 (16.0) 1.135 (28.8) 1.390 (35.3)
16 17 .938-20 UNEF 1.250 (31.8) 1.410 (35.8) .756 (19.2) 1.135 (28.8) 1.390 (35.3)
18 19 1.063-18 UNEF 1.400 (35.6) 1.520 (38.6) .845 (21.5) 1.195 (30.4) 1.390 (35.3)
20 21 1.188-18 UNEF 1.500 (38.1) 1.640 (41.7) .970 (24.6) 1.325 (33.7) 1.390 (35.3)
22 23 1.313-18 UNEF 1.650 (41.9) 1.770 (45.0) 1.095 (27.8) 1.445 (36.7) 1.390 (35.3)
24 25 1.438-18 UNEF 1.750 (44.5) 1.890 (48.0) 1.220 (31.0) 1.585 (40.3) 1.390 (35.3)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
4. Metric dimensions (mm) are in parentheses.
Basic Part Number
M85049/56 = Straight
M85049/57 = 45° M85049/57 G 16 W
Shell
Size
Conguration
N = Non-Detented
G = Self-Locking with Ground Lug
H = Non-Detented with Ground Lug
S = Self-Locking without Ground Lug
–– = Non Self-Locking
OPTIONAL
SELF-LOCKING
COUPLING
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-80
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/58
Potting Boot Ring (MS27458)
1. For complete dimensions see the applicable Military
Specication.
2. Finish: 500-Hour Cadmium Olive Drab over Electroless Nickel.
APPLICATION NOTES
3. See Pages 30-5 and 68-14 or the AS85049/75 Potting Boot
which can be used with this potting ring.
4. Metric dimensions (mm) are in parentheses.
Dash Number
Basic Part Number
M85049/58 -10
TABLE I: Dash Number, Shell Size and Dimensions
Dash
No. Shell
Size
(Ref)
A
Thread
UNEF-2B
B
Dia
Max
C
Dia
Max
D
Dia
±.005 (.1)
88/9 .4375-28 .600 (15.2) .506 (12.9) .344 (8.7)
10 10/11 .5625-24 .726 (18.4) .631(16.0) .472 (12.0)
12 12/13 .6875-24 .850 (21.6) .756 (19.2) .586 (14.9)
14 14/15 .8125-20 .976 (24.8) .881 (22.4) .711 (18.1)
16 16/17 .9375-20 1.012 (25.7) 1.006 (25.6) .836 (21.2)
18 18/19 1.0625-18 1.226 (31.1) 1.131 (28.7) .942 (23.9)
20 20/21 1.1875-18 1.352 (34.3) 1.256 (31.9) 1.067 (27.1)
22 22/23 1.3125-18 1.476 (37.5) 1.381 (35.1) 1.192 (30.3)
24 24/25 1.4375-18 1.602 (40.7) 1.506 (38.3) 1.317 (33.5)
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-81
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/59
Straight Shrink Boot Adapter
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
Finish
A = Black Anodize
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
Basic
Part Number
M85049/59 -A 10
Adapter
Size
TABLE I: Adapter Size, Thread and Dimensions
Adapter
Size A Thread
Class 2B-LH B
Max F
±.016 (0.4) G
±.031 (0.8) H Dia
±.010 (0.3)
12 .750 - 20 UNEF .933 (23.7) .479 (6.4) 1.175 (29.8) .798 (20.3)
14 .875 - 20 UNEF 1.057 (26.8) .479 (6.4) 1.175 (29.8) .922 (23.4)
16 1.000 - 20 UNEF 1.182 (30.0) .479 (6.4) 1.175 (29.8) 1.048 (26.6)
18 1.125 - 18 UNEF 1.307 (33.2) .479 (6.4) 1.175 (29.8) 1.172 (29.8)
20 1.250 - 18 UNEF 1.432 (36.4) .479 (6.4) 1.175 (29.8) 1.297 (32.9)
22 1.375 - 18 UNEF 1.557 (39.5) .479 (6.4) 1.175 (29.8) 1.423 (36.1)
24 1.625 - 18 UNEF 1.797 (45.6) .479 (6.4) 1.175 (29.8) 1.662 (42.2)
28 1.875 - 16 UN 2.057 (52.2) .479 (6.4) 1.175 (29.8) 1.922 (48.8)
32 2.062 - 16 UN 2.307 (58.6) .479 (6.4) 1.175 (29.8) 2.172 (55.2)
36 2.312 - 16 UN 2.557 (64.9) .479 (6.4) 1.175 (29.8) 2.422 (61.5)
40 2.625 - 16 UN 2.869 (72.9) .667 (16.9) 1.375 (44.9) 2.734 (69.4)
44 2.875 - 16 UN 3.120 (79.2) .667 (16.9) 1.375 (44.9) 2.982 (75.7)
CONNECTOR DESIGNATOR:
CMIL-DTL-22992
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-82
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/60-1 and MS3158
Straight Shrink Boot Adapter
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
Basic Part Number
M85049/60-1 W 22
Shell Size
TABLE I: Shell Size, Thread and Dimensions
Shell
Size
A Thread
Class 2B
C Dia Max
+.000 (0.0)
-.045 (1.14)
E
Min
Dia
F Dia
+.000 (0.0)
-.020 (0.5)
G
Max
3.562 - 24 UNEF .670 (17.0) .250 (6.4) .533 (13.5) .832 (21.1)
8.500 - 20 UNF .620 (15.7) .250 (6.4) .533 (13.5) .832 (21.1)
10 .625 - 24 UNEF .740 (18.8) .355 (9.0) .605 (15.4) .832 (21.1)
12 .750 - 20 UNEF .860 (21.8) .491 (12.5) .774 (19.7) .832 (21.1)
14 .875 - 20 UNEF .980 (24.9) .565 (14.4) .838 (21.3) .832 (21.1)
16 1.000 - 20 UNEF 1.110 (28.2) .690 (17.5) .963 (24.5) .832 (21.1)
18 1.062 - 18 UNEF 1.220 (31.0) .769 (19.5) 1.042 (26.5) .832 (21.1)
20 1.188 - 18 UNEF 1.350 (34.3) .894 (22.7) 1.217 (30.9) .832 (21.1)
22 1.313 - 18 UNEF 1.470 (37.3) 1.019 (25.9) 1.355 (34.4) .832 (21.1)
24 1.438 - 18 UNEF 1.590 (40.4) 1.134 (28.8) 1.443 (36.7) .832 (21.1)
28 1.750 - 18 UNS 1.970 (50.0) 1.369 (34.8) 1.709 (43.4) .994 (25.3)
32 2.000 - 18 UNS 2.220 (56.4) 1.615 (41.0) 1.919 (48.7) .994 (25.3)
36 2.250 - 16 UN 2.470 (62.7) 1.830 (46.5) 2.169 (55.1) .994 (25.3)
40 2.500 - 16 UN 2.720 (69.1) 2.045 (51.9) 2.402 (61.0) .994 (25.3)
44 2.750 - 16 UN 2.970 (75.4) 2.300 (58.4) 2.657 (67.5) .994 (25.3)
48 3.000 - 16 UN 3.220 (81.8) 2.550 (64.8) 2.907 (73.8) .994 (25.3)
61 1.500 - 18 UNEF 1.650 (41.9) 1.174 (29.8) 1.529 (38.8) .832 (21.1)
Basic
Part Number
MS3158 -22 C
Shell
Size
Superseded Part Number
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3
EN 2997, EN 3646
ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2
PATT 602
Finish
A = Black Anodize
N = Electroless Nickel
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
Finish
C = Cadmium Olive Drab over
Electroless Nickel
N = Electroless Nickel
Rev. 06.14.17
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-83
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
AS85049/60-2G and MS3416-G
Straight Shrink Boot Adapter
Basic Part Number
M85049/60-2G 22 W
Shell Size
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
Superseded Part Number
Basic
Part Number
Shell
Size
MS3416 -22 G C
Style
TABLE I: Shell Size, Thread and Dimensions
Shell
Size
A Thread
Class 2B
D Dia
+.000 (0.0)
-.020 (0.5)
F Dia
+.000 (0.0)
-.045 (1.1)
G
Max
3.562 - 24 UNEF .709 (18.0) .750 (19.1) .540 (13.7)
8.500 - 20 UNF .657 (16.7) .688 (17.5) .540 (13.7)
10 .625 - 24 UNEF .774 (19.7) .803 (20.4) .540 (13.7)
12 .750 - 20 UNEF .898 (22.8) .938 (23.8) .540 (13.7)
14 .875 - 20 UNEF 1.024 (26.0) 1.063 (27.0) .540 (13.7)
16 1.000 - 20 UNEF 1.152 (29.3) 1.238 (31.4) .540 (13.7)
18 1.062 - 18 UNEF 1.243 (31.6) 1.310 (33.3) .540 (13.7)
20 1.188 - 18 UNEF 1.370 (34.8) 1.436 (36.5) .540 (13.7)
22 1.313 - 18 UNEF 1.443 (36.7) 1.560 (39.6) .540 (13.7)
24 1.438 - 18 UNEF 1.618 (41.1) 1.686 (42.8) .540 (13.7)
28 1.750 - 18 UNS 1.969 (50.0) 2.062 (52.4) .702 (17.8)
32 2.000 - 18 UNS 2.219 (56.4) 2.312 (58.7) .702 (17.8)
36 2.250 - 16 UN 2.469 (62.7) 2.562 (65.1) .702 (17.8)
40 2.500 - 16 UN 2.719 (69.1) 2.812 (71.4) .702 (17.8)
44 2.750 - 16 UN 2.969 (75.4) 3.062 (77.8) .702 (17.8)
48 3.000 - 16 UN 3.219 (81.8) 3.312 (84.1) .702 (17.8)
61 1.500 - 18 UNEF 1.653 (42.0) 1.748 (44.4) .540 (13.7)
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3
EN 2997, EN 3646
ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2
PATT 602
Finish
A = Black Anodize
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
Finish
A = 1,000 Hr. Cadmium Olive Drab
C = Cadmium Olive Drab
N = Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-84
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/61
Potting Boot Ring
Dash Number
Basic Part Number
M85049/61 -10
TABLE I: Dash Number and Dimensions
Dash
No. Shell
Size
(Ref)
A
Thread
UNEF-2B
B
Dia
Max
C
Dia
Max
D
Dia
±.005 (.1)
88/9 .4375-28 .594 (15.1) .521 (13.2) .476 (12.1)
10 10/11 .5625-24 .734 (18.6) .647(16.4) .602 (15.3)
12 12/13 .6875-24 .844 (21.4) .771 (19.6) .726 (18.4)
14 14/15 .8125-20 .969 (24.6) .897 (22.8) .852 (21.6)
16 16/17 .9375-20 1.094 (27.8) 1.023 (26.0) .978 (24.8)
18 18/19 1.0625-18 1.234 (31.3) 1.147 (29.1) 1.102 (28.0)
20 20/21 1.1875-18 1.344 (34.1) 1.273 (32.3) 1.228 (31.2)
22 22/23 1.3125-18 1.469 (37.3) 1.397 (35.5) 1.352 (34.3)
24 24/25 1.4375-18 1.594 (40.5) 1.524 (38.7) 1.478 (37.5)
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Finish: 500-Hour Cadmium Olive Drab over Electroless Nickel.
3. See Pages 30-4 and 68-13 for the AS85049/75 Potting Boot
which can be used with this potting ring and Page 88-13
4. Metric dimensions (mm) are in parentheses.
CONNECTOR DESIGNATOR:
FMIL-DTL-27599
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-85
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/62 and M38999/2
Straight Shrink Boot Adapter
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
TABLE I: Shell Size, Thread and Dimensions
Shell
Size A Thread
Class 2B C
Max
E
Dia
Min
F
Dia
Min
G
Max
08 .438 - 28 UNEF .750 (19.1) .250 (6.4) .533 (13.5) 1.000 (25.4)
10 .562 - 24 UNEF .850 (21.6) .375 (9.5) .605 (15.4) 1.000 (25.4)
12 .688 - 24 UNEF 1.000 (25.4) .500 (12.7) .774 (19.7) 1.000 (25.4)
14 .813 - 20 UNEF 1.100 (27.9) .625 (15.9) .838 (21.3) 1.000 (25.4)
16 .938 - 20 UNEF 1.250 (31.8) .750 (19.1) .963 (24.5) 1.000 (25.4)
18 1.063 - 18 UNEF 1.400 (35.6) .812 (20.6) 1.042 (26.5) 1.000 (25.4)
20 1.188 - 18 UNEF 1.500 (38.1) .937 (23.8) 1.217 (30.9) 1.000 (25.4)
22 1.313 - 18 UNEF 1.650 (41.9) 1.062 (27.0) 1.355 (34.4) 1.000 (25.4)
24 1.438 - 18 UNEF 1.750 (44.5) 1.188 (30.2) 1.443 (36.7) 1.000 (25.4)
Basic
Part Number
M85049/62 -10 W D
Shell
Size Drain Hole Option
(Omit for None)
CONNECTOR DESIGNATOR:
F
MIL-DTL-38999 Series I & II
40M38277, PAN 6433-1
PATT 614, PATT 616
NFC93422 Series HE308 &
HE309
Finish
A = Black Anodize
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-86
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/63
90° Qwik-Ty Strain Relief
Optional Self-Locking • Optional Ground Lug
TABLE I: Shell Size, Thread, Cable Entry and Backshell Dimensions
Shell
Size
Series II
Series I
Shell Size
Ref.
A Thread
Class 2B
C Dia
Max
E Dia
Max
F
Cable Entry
J
Max
K
Self-Locking
8 9 .438-28 UNEF .750 (19.1) .860 (21.8) .264 (6.7) 1.220 (31.0) .630 (16.0)
10 11 .562-24 UNEF .850 (21.6) .980 (24.9) .392 (10.0) 1.290 (32.8) .630 (16.0)
12 13 .688-24 UNEF 1.000 (25.4) 1.160 (29.5) .506 (12.9) 1.620 (41.1) .630 (16.0)
14 15 .813-20 UNEF 1.100 (27.9) 1.280 (32.5) .631 (16.0) 1.660 (42.2) .700 (17.8)
16 17 .938-20 UNEF 1.250 (31.8) 1.410 (35.8) .756 (19.2) 1.720 (43.7) .700 (17.8)
18 19 1.063-18 UNEF 1.400 (35.6) 1.520 (38.6) .845 (21.5) 1.720 (43.7) .730 (18.5)
20 21 1.188-18 UNEF 1.500 (38.1) 1.640 (41.7) .970 (24.6) 1.790 (45.5) .730 (18.5)
22 23 1.313-18 UNEF 1.650 (41.9) 1.770 (45.0) 1.095 (27.8) 1.850 (47.0) .730 (18.5)
24 25 1.438-18 UNEF 1.750 (44.5) 1.890 (48.0) 1.220 (31.0) 1.910 (48.5) .730 (18.5)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
4. Metric dimensions (mm) are in parentheses.
Basic Part Number
M85049/63 = 90° M85049/63 G 16 W
Shell
Size
Conguration
N = Non-Detented
G = Self-Locking with Ground Lug
H = Non-Detented with Ground Lug
S = Self-Locking without Ground Lug
–– = Non Self-Locking
OPTIONAL
SELF-LOCKING
COUPLING
Finish
A = Anodize, Black
N = Electroless Nickel
W = 1,000 Hour Cadmium Olive Drab
over Electroless Nickel
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc-Nickel, Black
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-87
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/69
Straight Shrink Boot Adapter
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm)
are in parentheses.
TABLE I: Shell Size, Thread and Dimensions
Shell
Size A Thread
Class 6H C
Max E Dia
Min F
Dia Max G
Max
9M12 X 1 - 6H .750 (19.1) .250 (6.4) .533 (13.5) .710 (18.0)
11 M15 X 1 - 6H .850 (21.6) .375 (9.5) .605 (15.4) .710 (18.0)
13 M18 X 1 - 6H 1.000 (25.4) .500 (12.7) .774 (19.7) .710 (18.0)
15 M22 X 1 - 6H 1.150 (29.2) .625 (15.9) .838 (21.3) .710 (18.0)
17 M25 X 1 - 6H 1.250 (31.8) .750 (19.1) .963 (24.5) .710 (18.0)
19 M28 X 1 - 6H 1.400 (35.6) .812 (20.6) 1.042 (26.5) .710 (18.0)
21 M31 X 1 - 6H 1.550 (39.4) .938 (23.8) 1.217 (30.9) .710 (18.0)
23 M34 X 1 - 6H 1.650 (41.9) 1.062 (27.0) 1.355 (34.4) .710 (18.0)
25 M37 X 1 - 6H 1.785 (47.0) 1.188 (30.2) 1.443 (36.7) .710 (18.0)
Basic
Part Number
M85049/69 -11 A D
Shell
Size Drain Hole Option
(Omit for None)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN3645
Finish
A = Black Anodize
N = Electroless Nickel
W = 1000 Hr. Cadmium Olive Drab
X = Nickel Fluorocarbon Polymer
Y = Pure Dense Electrodeposited Aluminum
Z = Zinc Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-88
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/74
Potting Boot
For Use with
AS85049/61
Potting Boot Ring
(Page B-84)
TABLE I: Shell Size and Dimensions
Shell
Size A
Min A
Max B Dia
± .005 (.1) G
Max C
Min ID D
Max E
Max F
Min
8450 (11.4) .500 (12.7) .511 (13.0) .608 (15.4) .317 (8.1) .766 (19.5) 1.000 (25.4) .110 (2.8)
10 .450 (11.4) .500 (12.7) .637 (16.2) .734 (18.6) .434 (11.0) .922 (23.4) 1.125 (28.6) .200 (5.1)
12 .450 (11.4) .500 (12.7) .761 (19.3) .858 (21.8) .548 (13.9) 1.031 (26.2) 1.125 (28.6) .290 (7.4)
14 .450 (11.4) .500 (12.7) .887 (22.5) .984 (25.0) .673 (17.1) 1.016 (25.8) 1.297 (32.9) .400 (10.2)
16 .450 (11.4) .500 (12.7) 1.013 (25.7) 1.110 (28.2) .798 (20.3) 1.016 (25.8) 1.375 (34.9) .490 (12.4)
18 .450 (11.4) .500 (12.7) 1.137 (28.9) 1.234 (31.3) .899 (22.8) 1.078 (27.4) 1.469 (37.3) .590 (15.0)
20 .550 (14.0) .594 (15.1) 1.263 (32.1) 1.360 (34.5) 1.024 (26.0) 1.094 (27.8) 1.625 (41.3) .730 (18.5)
22 .550 (14.0) .594 (15.1) 1.387 (35.2) 1.484 (37.7) 1.149 (29.2) 1.094 (27.8) 1.703 (43.3) .860 (21.8)
24 .550 (14.0) .594 (15.1) 1.513 (38.4) 1.610 (40.9) 1.274 (32.4) 1.281 (32.5) 2.047 (52.0) 1.070 (27.2)
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Material: Translucent nylon, minimum wall thickness .020 (.51).
3. Metric dimensions (mm) are in parentheses.
Shell
Size
Basic Part Number
M85049/74 -10 -1
Geometry
1 - Straight
2 = 90°
A
B
C
D
E
F Min Cross
Section
B
G
G
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-89
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/75
Potting Boot
TABLE I: Shell Size and Dimensions
Shell
Size B Dia
± .005 (.1) C
Min ID D
Max E
Max F
Min
8527 (13.4) .434 (11.0) .438 (11.1) .766 (19.5) .073 (1.9)
10 .652 (16.6) .548 (13.9) .469 (11.9) .891 (22.6) .117 (3.0)
12 .776 (19.7) .673 (17.1) .562 (14.3) 1.031 (26.2) .206 (5.2)
14 .898 (22.8) .798 (20.3) .719 (18.3) 1.156 (29.4) .384 (9.8)
16 1.016 (25.8) .899 (22.8) .781 (19.8) 1.287 (32.7) .443 (11.3)
18 1.140 (29.0) 1.024 (26.0) .844 (21.4) 1.406 (35.7) .561 (14.2)
20 1.265 (32.1) 1.149 (29.2) .906 (23.0) 1.531 (38.9) .693 (17.6)
22 1.390 (35.3) 1.274 (32.4) .938 (23.8) 1.656 (42.1) .840 (21.3)
24 1.515 (38.5) 1.399 (35.5) 1.031 (26.2) 1.781 (45.2) .999 (25.4)
For Use with
AS85049/58
Potting Boot Ring
(Page B-80)
Shell
Size
Basic Part Number
M85049/75 -10 -1
Geometry
1 - Straight
2 = 90°
s
Section
.297
(7.5)
Max
B
C
D
E
F Min Cros
B
.031 (.8)
± .010 (.3)
.031 (.8)
± .010 (.3)
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Material: Translucent nylon, minimum wall thickness .020 (.51).
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-90
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/76
90° EMI/RFI Environmental Backshell
TABLE I: Shell Size,
Thread and Dimensions
Dash
No. Shell
Size
Series I
Shell
Size
Series II
A Thread
Class 2B C Dia
Max
08 09 08 .438 - 28 UNEF .750 (19.1)
10 11 10 .562 - 24 UNEF .850 (21.6)
12 13 12 .688 - 24 UNEF 1.000 (25.4)
14 15 14 .813 - 20 UNEF 1.150 (29.2)
16 17 16 .938 - 20 UNEF 1.250 (31.8)
18 19 18 1.063 - 18 UNEF 1.400 (35.6)
20 21 20 1.188 - 18 UNEF 1.550 (39.4)
22 23 22 1.313 - 18 UNEF 1.650 (41.9)
24 25 24 1.438 - 18 UNEF 1.850 (47.0)
TABLE II: Shell Size, Series 1 Reference,
Clamp Size and Dimensions
Dash
No. Shell
Size
Series I
Shell
Size
Series II
Clamp Size
Min Max E
± .156 (4.0) F
± .188 (4.8)
08 09 08 01 02 .532 (13.5) 3.267 (83.0)
10 11 10 01 03 .627 (15.9) 3.387 (86.0)
12 13 12 02 04 .642 (16.3) 3.407 (86.5)
14 15 14 02 05 .719 (18.3) 3.477 (88.3)
16 17 16 02 06 .774 (19.7) 3.567 (90.6)
18 19 18 03 07 .854 (21.7) 3.737 (94.9)
20 21 20 03 08 .899 (22.8) 3.737 (94.9)
22 23 22 03 09 1.009 (25.6) 3.847 (97.7)
24 25 24 04 10 1.024 (26.0) 3.847 (97.7)
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size,
Cable Range and Dimensions
Clamp
Size Cable Range
Min Max G
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .375 (9.5) .500 (12.7) 1.200 (30.5)
05 .500 (12.7) .625 (15.9) 1.250 (31.8)
06 .625 (15.9) .750 (19.1) 1.400 (35.6)
07 .750 (19.1) .875 (22.2) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.650 (41.9)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5)
10 1.125 (28.6) 1.250 (31.8) 1.900 (48.3)
Basic
Part Number
M85049/76 -10 W 01
Dash Number
(Table I) Clamp Size
(Tables II & III)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-91
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/77
45° EMI/RFI Environmental Backshell
TABLE I: Shell Size,
Thread and Dimensions
Dash
No. Shell
Size
Series I
Shell
Size
Series II
A Thread
Class 2B C Dia
Max
08 09 08 .438 - 28 UNEF .750 (19.1)
10 11 10 .562 - 24 UNEF .850 (21.6)
12 13 12 .688 - 24 UNEF 1.000 (25.4)
14 15 14 .813 - 20 UNEF 1.150 (29.2)
16 17 16 .938 - 20 UNEF 1.250 (31.8)
18 19 18 1.063 - 18 UNEF 1.400 (35.6)
20 21 20 1.188 - 18 UNEF 1.550 (39.4)
22 23 22 1.313 - 18 UNEF 1.650 (41.9)
24 25 24 1.438 - 18 UNEF 1.850 (47.0)
TABLE II: Shell Size, Series 1 Reference,
Clamp Size and Dimensions
Dash
No. Shell
Size
Series I
Shell
Size
Series II
Clamp Size
Min Max E
±.062 (1.6) F
±.062 (1.6)
08 09 08 01 02 .398 (10.1) 3.088 (78.4)
10 11 10 01 03 .458 (11.6) 3.148 (80.0)
12 13 12 02 04 .518 (13.2) 3.208 (81.5)
14 15 14 02 05 .588 (14.9) 3.298 (83.8)
16 17 16 02 06 .678 (17.2) 3.408 (86.6)
18 19 18 03 07 .868 (22.0) 3.598 (91.4)
20 21 20 03 08 .868 (22.0) 3.598 (91.4)
22 23 22 03 09 .958 (24.3) 3.748 (95.2)
24 25 24 04 10 .958 (24.3) 3.748 (95.2)
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size,
Cable Range and Dimensions
Clamp
Size Cable Range
Min Max G
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .375 (9.5) .500 (12.7) 1.200 (30.5)
05 .500 (12.7) .625 (15.9) 1.250 (31.8)
06 .625 (15.9) .750 (19.1) 1.400 (35.6)
07 .750 (19.1) .875 (22.2) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.650 (41.9)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5)
10 1.125 (28.6) 1.250 (31.8) 1.900 (48.3)
Basic
Part Number
M85049/77 -10 W 01
Dash Number
(Table I) Clamp Size
(Tables II & III)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-92
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/78
45° EMI/RFI Environmental Backshell
TABLE I: Shell Size,
Thread and Dimensions
Shell
Size A Thread
Class 2B B Dia
Max
09 M12 X 1 - 6H .750 (19.1)
11 M15 X 1 - 6H .850 (21.6)
13 M18 X 1 - 6H 1.000 (25.4)
15 M22 X 1 - 6H 1.150 (29.2)
17 M25 X 1 - 6H 1.250 (31.8)
19 M28 X 1 - 6H 1.400 (35.6)
21 M31 X 1 - 6H 1.550 (39.4)
23 M34 X 1 - 6H 1.650 (41.9)
25 M37 X 1 - 6H 1.850 (47.0)
TABLE II: Shell Size,
Clamp Size and Dimensions
Shell
Size Clamp Size
Min Max F
±.062 (1.6) G
±.062 (1.6)
09 01 02 .398 (10.1) 3.088 (78.4)
11 01 03 .458 (11.6) 3.148 (80.0)
13 02 04 .518 (13.2) 3.208 (81.5)
15 02 05 .588 (14.9) 3.298 (83.8)
17 02 06 .678 (17.2) 3.408 (86.6)
19 03 07 .868 (22.0) 3.598 (91.4)
21 03 08 .868 (22.0) 3.598 (91.4)
23 03 09 .958 (24.3) 3.748 (95.2)
25 04 10 .958 (24.3) 3.748 (95.2)
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size,
Cable Range and Dimensions
Clamp
Size Cable Range
Min Max H
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .375 (9.5) .500 (12.7) 1.200 (30.5)
05 .500 (12.7) .625 (15.9) 1.250 (31.8)
06 .625 (15.9) .750 (19.1) 1.400 (35.6)
07 .750 (19.1) .875 (22.2) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.650 (41.9)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5)
10 1.125 (28.6) 1.250 (31.8) 1.900 (48.3)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999, Series III and IV
EN3645
Basic
Part Number
M85049/78 -10 W 01
Shell Size
(Tables I & II) Clamp Size
(Tables II & III)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-93
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/79
90° EMI/RFI Environmental Backshell
TABLE II: Shell Size,
Clamp Size and Dimensions
Shell
Size Clamp Size
Min Max F
±.156 (4.0) G
±.188 (4.8)
09 01 02 .532 (13.5) 3.267 (83.0)
11 01 03 .627 (15.9) 3.387 (86.0)
13 02 04 .642 (16.3) 3.407 (86.5)
15 02 05 .719 (18.3) 3.477 (88.3)
17 02 06 .774 (19.7) 3.567 (90.6)
19 03 07 .854 (21.7) 3.737 (94.9)
21 03 08 .899 (22.8) 3.737 (94.9)
23 03 09 1.009 (25.6) 3.847 (97.7)
25 04 10 1.024 (26.0) 3.847 (97.7)
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE III: Clamp Size,
Cable Range and Dimensions
Clamp
Size Cable Range
Min Max H
Max
01 .062 (1.6) .125 (3.2) .800 (20.3)
02 .125 (3.2) .250 (6.4) 1.000 (25.4)
03 .250 (6.4) .375 (9.5) 1.100 (27.9)
04 .375 (9.5) .500 (12.7) 1.200 (30.5)
05 .500 (12.7) .625 (15.9) 1.250 (31.8)
06 .625 (15.9) .750 (19.1) 1.400 (35.6)
07 .750 (19.1) .875 (22.2) 1.500 (38.1)
08 .875 (22.2) 1.000 (25.4) 1.650 (41.9)
09 1.000 (25.4) 1.125 (28.6) 1.750 (44.5)
10 1.125 (28.6) 1.250 (31.8) 1.900 (48.3)
TABLE I: Shell Size,
Thread and Dimensions
Shell
Size A Thread
Class 2B B Dia
Max
09 M12 X 1 - 6H .750 (19.1)
11 M15 X 1 - 6H .850 (21.6)
13 M18 X 1 - 6H 1.000 (25.4)
15 M22 X 1 - 6H 1.150 (29.2)
17 M25 X 1 - 6H 1.250 (31.8)
19 M28 X 1 - 6H 1.400 (35.6)
21 M31 X 1 - 6H 1.550 (39.4)
23 M34 X 1 - 6H 1.650 (41.9)
25 M37 X 1 - 6H 1.850 (47.0)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999, Series III and IV
EN3645
Basic
Part Number
M85049/79 -10 W 01
Shell Size
(Tables I & II) Clamp Size
(Tables II & III)
Finish
N = Electroless Nickel X = Aluminum, Nickel Flurocarbon Polymer
W = 1,000 Hr. Cadmium Olive Drab Z = Aluminum, Zinc-Nickel, Black
over Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-94
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/80
Sealing Plug for MIL-DTL-38999 Connectors
Contact Sizes 8, 12 and 16
Basic
Part Number
M85049/80 -16
Dash
Number
Dimensions and Conguration for Size 8 Contacts
1.506 (38.25) +.000 (0.0) -.040 (1.02)
.840 (21.34)
.810 (20.57)
.029 (0.74)
+.004 (0.10) -.0
.015
(0.38)
x 45°
.219 (5.56)
.217 (5.51) Dia
.316 (8.03)
.313 (7.95) Dia
.151 (3.84)
.141 (3.58) Dia
.258
(6.55)
Min
.271
(6.88)
+ 0 (0.0)
-.020 (0.51)
45°
Typ
.155 (3.94)
+ 0 -.003 (0.08)
Dia
.276 (7.01)
+ 0 -.003 (0.08)
Dimensions and Conguration for Size 12 Contacts
.029 (0.74)
+.004 -.000
(+0.10 -0)
.015 x 45° .095 (2.41)
+.000 (0.0)
-.002 (0.05)
.182 (4.62)
+.000 (0.0)
-.003 (0.08)
.050 (1.27)
+.010 (0.25)
-.000 (0.0) Dia
Dia
.151 (3.84)
+.000 (0.0)
-.003 (0.08) Dia
.020 (0.51)
.010 (0.25)
Chamfer (Optional Rad Max)
x 45° ±.5°
45° Typ
.271
(6.88)
+.000 (0.0)
-.010 (0.25)
.237 (6.02)
+.000 (0.0)
-.020 (0.51)
.205
(5.21)
Min
1.506 +.000 -.040
(38.25 +0 -1.02)
.130 (3.30)
+0 -.020 (0.51)Dia
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-95
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/80
Sealing Plug for MIL-DTL-38999 Connectors
Contact Sizes 8, 12 and 16
Dimensions and Conguration for Size 16 Contacts
.029 (0.74)
+.004 -.000
(+0.10 -0)
.010 x 45° .063 (1.60)
+.000 (0.0)
-.002 (0.05)
.130 (3.30)
+.000 (0.0)
-.003 (0.08)
.020 (0.51)
+.010 (0.25)
-.000 (0.0) Dia
Dia
.103 (2.62)
+.000 (0.0)
-.002 (0.05) Dia
.020 (0.51)
.010 (0.25)
Chamfer (Optional Rad Max)
x 45° ±.5°
45° Typ
.271
(6.88)
+.000 (0.0)
-.010 (0.25)
.237 (6.02)
+.000 (0.0)
-.010 (0.25)
.205
(5.21)
Min
1.506 +.000 -.040
(38.25 +0 -1.02)
.093 (2.36)
+0 -.020 (0.51)Dia
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. Color:
Size 16 - Blue, IAW EIA RS359
Size 12 - Yellow, IAW EIA RS359
Size 8 - Green, IAW EIA RS359
3. Insulation resistance: 100 megaohms minimum at 500V DC when tested IAW EIA 364-21, using at probes placed on opposite ends
of the dummy contact.
4. Size 16 is for use in MIL-DTL-Series I, III or IV connectors in size 16 contact cavities. Size 12 is for use in MIL-DTL-38999 Series I, III
or IV connectors in size 12 contact cavities. Size 8 is for use in MIL-DTL-38999 Series I, III or IV connectors in size 8 cavities.
5. Sizes 16, 12 and 8 dummy contacts are to be used in lieu of contacts and sealing plugs in unwired contact cavities for both pin and
socket inserts.
6. The size 8 dummy contact requires an additional boot (to be provided by the connector manufacturer) for insert arrangements 17-2,
19-18, 21-75, 25-7, 25-8, 25-46 and 25-90 to seal the cavity.
7. For complete dimensions, see the applicable Military Specication.
8. Metric dimensions (mm) are in parentheses.
Table I: Insertion and Removal Tools
Figure Size Type
Glenair
Part Number
Military Part
Number
# Insertion/Extraction - M/-
# Insertion/extraction - M/-
# Extraction only - M/-
Figure 1 Figure 2 Figure 3
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-96
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/81
Sealing Plug for MIL-DTL-38999 Connectors
Basic
Part Number
M85049/81 -10
Dash
Number
A
BD
C E
G Dia T yp
H Dia T yp
F Dia
45°
Typ
TABLE I: Dimensions
Dash
No. A
Dim B
Dim C
Dim D
Dim E
Dim F
Dia G
Dia H
Dia
10 .702 (17.83)
.672 (17.07) .255 (6.48)
.245 (6.22) .034 (0.86)
.028 (0.71) .255 (6.48)
.245 (6.22) .034 (0.86)
.028 (0.71) .155 (3.94)
.149 (3.78) .130 (3.30)
.120 (3.05) .185 (4.70)
.179 (4.55)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. Material and color:
Green polytetrauoroethylene, peruoroalkoxy (PFA) or uorinated ethylene propylene (FEP) rod, molded or extruded,
temperature limit 200°C minimum.
3. Insulation resistance: 100 megaohms minimum at 500V DC when tested IAW EIA 364-21, using at probes placed on opposite ends
of the sealing plug.
4. Tool: Size 10 insertion and removal tool, military part number M81969/14-05.
5. Designed for use with MIL-DTL-38999 connectors utilizing size 10 contact cavities for AS39029/56 and /58 contacts. Sealing plug to
be used in both pin and socket cavities.
6. For complete dimensions, see the applicable Military Specication.
7. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-97
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/82, AS85049/83 and AS85049/84
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
Basic Part Number
M85049/82 = Straight
M85049/83 = 45°
M85049/84 = 90° Shell Size
(Table I) Entry Size
(Table I)
APPLICATION NOTES
1. Assembly identied with manufacturer’s
name and part number, space permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
4. For use with AS85049/128 Bands.
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I and III
40M39569, DEF 5326-3, EN 2997,
EN 3646
ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2, PATT 602
–– = Detented
N = Non-Detented
M85049/82 N 16 P 02
Finish
N = Electroless Nickel
P = Cadmium, Olive Drab over Electroless Nickel with
Polysulde Sealant Strips
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
YP = Aluminum, Pure Dense Electrodeposited Aluminum with Polysulde Sealant Strips
Z = Aluminum, Zinc-Nickel, Black
ZP = Aluminum, Zinc Nickel with Polysulphide Sealant Strips
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-98
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
BTABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size A Thread
Class 2B C Dia
Max
E Dia
Cable Entry
Size 02
±.010 (0.30)
E Dia
Cable Entry
Size 03
±.010 (0.30)
F
Max G
Max H
Max J
Max
08 .500 - 20 UNF .886 (22.4) N/A .250 (6.4) .870 (22.1) 1.160 (29.5) 1.188 (30.2) 1.417 (36.0)
10 .625 - 24 UNEF 1.010 (25.7) N/A .312 (7.9) .890 (22.6) 1.180 (30.0) 1.281 (32.5) 1.480 (37.6)
12 .750 - 20 UNEF 1.130 (28.7) .312 (7.9) .438 (11.1) .920 (23.4) 1.200 (30.5) 1.406 (35.7) 1.542 (39.2)
14 .875 - 20 UNEF 1.260 (32.0) .438 (11.1) .562 (14.3) .940 (23.9) 1.220 (31.0) 1.531 (38.9) 1.605 (40.8)
16 1.000 - 20 UNEF 1.386 (35.1) .500 (12.7) .625 (15.9) .960 (24.4) 1.250 (31.8) 1.656 (42.1) 1.667 (42.3)
18 1.062 - 18 UNEF 1.510 (38.4) .625 (15.9) .750 (19.1) .980 (24.9) 1.260 (32.0) 1.718 (43.6) 1.730 (43.9)
20 1.188 - 18 UNEF 1.636 (41.4) .625 (15.9) .812 (20.6) 1.00 (25.4) 1.290 (32.8) 1.844 (46.8) 1.792 (45.5)
22 1.313 - 18 UNEF 1.760 (44.7) .688 (17.5) .938 (23.8) 1.030 (26.2) 1.310 (33.3) 1.938 (49.2) 1.850 (47.0)
24 1.438 - 18 UNEF 1.886 (47.8) .750 (19.1) 1.000 (25.4) 1.050 (26.7) 1.340 (34.0) 2.093 (53.2) 1.917 (48.7)
28 1.750 - 18 UNS 2.136 (54.1) .875 (22.2) 1.125 (28.6) 1.100 (27.9) 1.380 (35.1) 2.531 (64.3) 2.042 (51.9)
AS85049/82, AS85049/83 and AS85049/84
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-99
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/85, AS85049/86 and AS85049/87
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
Basic Part Number
M85049/85 = Straight
M85049/86 = 45°
M85049/87 = 90°
Shell Size
(Table I)
Entry Size
(Table I)
–– = Detented
N = Non-Detented
M85049/85 N 16 P 02
O-Ring Typ
Finish
N = Electroless Nickel
P = Cadmium, Olive Drab over Electroless Nickel with
Polysulde Sealant Strips
W = 1,000 Hr. Cadmium Olive Drab over Electroless Nickel
X = Aluminum, Nickel Fluorocarbon Polymer
YP = Aluminum, Pure Dense Electrodeposited Aluminum with Polysulde Sealant Strips
Z = Aluminum, Zinc-Nickel, Black
ZP = Aluminum, Zinc Nickel with Polysulphide Sealant Strips
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-100
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/85, AS85049/86 and AS85049/87
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size
A Thread
Class 2B
C Dia
Max
F
Max
G
Max
H
Max
J
Max
08 .438 - 28 UNEF .860 (21.8) .870 (22.1) 1.160 (29.5) 1.375 (34.9) 1.375 (34.9)
10 .562 - 24 UNEF .990 (25.1) .900 (22.9) 1.190 (30.2) 1.437 (36.5) 1.437 (36.5)
12 .688 - 24 UNEF 1.160 (29.5) .920 (23.4) 1.210 (30.7) 1.562 (39.7) 1.562 (39.7)
14 .813 - 20 UNEF 1.280 (32.5) .950 (24.1) 1.240 (31.5) 1.687 (42.8) 1.687 (42.8)
16 .938 - 20 UNEF 1.410 (35.8) .980 (24.9) 1.260 (32.0) 1.750 (44.5) 1.750 (44.5)
18 1.063 - 18 UNEF 1.520 (38.6) .980 (24.9) 1.270 (32.3) 1.875 (47.6) 1.875 (47.6)
20 1.188 - 18 UNEF 1.640 (41.7) 1.010 (25.7) 1.300 (33.0) 1.938 (49.2) 1.938 (49.2)
22 1.313 - 18 UNEF 1.770 (45.0) 1.040 (26.4) 1.330 (33.8) 2.062 (52.4) 2.062 (52.4)
24 1.438 - 18 UNEF 1.890 (48.0) 1.070 (27.2) 1.350 (34.3) 2.125 (54.0) 2.125 (54.0)
TABLE II: Shell Size and
Cable Entry for Straight
Conguration Only
Shell
Size
E Dia
Cable Entry
Size 01
±.010 (0.30)
E Dia
Cable Entry
Size 02
±.010 (0.30)
08 N/A .250 (6.4)
10 N/A .312 (7.9)
12 .312 (7.9) .438 (11.1)
14 .438 (11.1) .562 (14.3)
16 .500 (12.7) .625 (15.9)
18 .625 (15.9) .750 (19.1)
20 .625 (15.9) .812 (20.6)
22 .688 (17.5) .938 (23.8)
24 .750 (19.1) 1.000 (25.4)
TABLE III: Shell Size and
Cable Entry for 45° and 90°
Congurations Only
Shell
Size
K Dia
Cable Entry
Size 02
±.010 (0.30)
K Dia
Cable Entry
Size 03
±.010 (0.30)
08 N/A .250 (6.4)
10 N/A .312 (7.9)
12 .312 (7.9) .438 (11.1)
14 .438 (11.1) .562 (14.3)
16 .500 (12.7) .625 (15.9)
18 .625 (15.9) .750 (19.1)
20 .625 (15.9) .812 (20.6)
22 .688 (17.5) .938 (23.8)
24 .750 (19.1) 1.000 (25.4)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
4. For use with AS85049/128 Bands.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-101
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
Basic Part Number
M85049/88 = Straight
M85049/89 = 45°
M85049/90 = 90°
Shell Size
(Table I)
Entry Size
(Table I)
–– = Detented
N = Non-Detented
M85049/88 N 17 P 02
Finish
(Table II)
O-Ring Typ
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part
number, space permitting.
2. For complete dimensions, see the applicable Military
Specication.
3. Metric dimensions (mm) are in parentheses.
4. For use with AS85049/128 Bands.
AS85049/88, AS85049/89 and AS85049/90
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-102
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size
A Thread
Class 2B
C Dia
Max
E Dia
Cable Entry
Size 02
±.010 (0.30)
E Dia
Cable Entry
Size 03
±.010 (0.30)
F
Max
G
Max
H
Max
J
Max
9 M12 X 1 - 6H .860
(21.8) N/A .250 (6.4) 1.010 (25.7) 1.160 (29.5) 1.375 (34.9) 1.417 (36.0)
11 M15 X 1 - 6H .990
(25.1) N/A .312 (7.9) 1.030
(26.2) 1.190
(30.2) 1.437
(36.5) 1.480
(37.6)
13 M18 X 1 - 6H 1.160
(29.5) .312 (7.9) .438
(11.1) 1.060
(26.9) 1.210
(30.7) 1.562
(39.7) 1.553
(39.4)
15 M22 X 1 - 6H 1.280
(32.5) .438
(11.1) .562
(14.3) 1.080
(27.4) 1.240
(31.5) 1.687
(42.8) 1.614
(41.0)
17 M25 X 1 - 6H 1.410 (35.8) .500 (12.7) .625 (15.9) 1.110 (28.2) 1.260 (32.0) 1.750 (44.5) 1.678 (42.6)
19 M28 X 1 - 6H 1.520
(38.6) .625
(15.9) .750
(19.1) 1.120
(28.4) 1.270
(32.3) 1.875
(47.6) 1.733
(44.0)
21 M31 X 1 - 6H 1.640
(41.7) .625
(15.9) .812
(20.6) 1.150
(29.2) 1.300
(33.0) 1.938
(49.2) 1.796
(45.6)
23 M34 X 1 - 6H 1.770
(45.0) .688
(17.5) .938
(23.8) 1.170
(29.7) 1.330
(33.8) 2.062
(52.4) 1.859
(47.2)
25 M37 X 1 - 6H 1.890
(48.0) .750
(19.1) 1.000
(25.4) 1.200
(30.5) 1.350
(34.3) 2.125
(54.0) 1.919
(48.7)
TABLE II: Finish and Material
Aluminum Composite Finish Description
GNot Available Electroless Nickel (Space Grade)
N M Electroless Nickel
P L Cadmium Olive Drab over Electroless
Nickel, Selective Plating
W J Cadmium Olive Drab
X XC Nickel Fluorocarbon Polymer
YP YL Pure Dense Electrodeposited
Aluminum, Selective Plating
Z ZC Zinc Nickel
ZP ZL Zinc Nickel, Selective Plating
AS85049/88, AS85049/89 and AS85049/90
Straight, 45° and 90° Banding Backshells
with Self-Locking Coupling
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-103
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/91 and AS85049/92
Composite Strain Reliefs
Self-Locking
A Thread
Typ.
C Dia
Typ.
F
G Typ.
(See Note 3)
H
Typ.
J
K
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV,
EN3645
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell
Size A Thread
Class 2B Ø C
Max F
Max G
Max Ø H
+.031 J
Max K
±.062 (1.6)
09 M12 X 1 - 6H .858 (21.8) .840 (21.3) .98 (24.9) .219 (5.6) 1.06 (26.9) .875 (22.2)
11 M15 X 1 - 6H .984 (25.0) .960 (24.4) 1.05 (26.7) .264 (6.7) 1.10 (27.9) .937 (23.8)
13 M18 X 1 - 6H 1.157 (29.4) 1.100 (27.9) 1.20 (30.5) .344 (8.7) 1.18 (30.0) 1.031 (26.2)
15 M22 X 1 - 6H 1.280 (32.5) 1.100 (27.9) 1.30 (33.0) .460 (11.7) 1.30 (33.0) 1.125 (28.6)
17 M25 X 1 - 6H 1.406 (35.7) 1.230 (31.2) 1.42 (36.1) .545 (13.8) 1.38 (35.1) 1.312 (33.3)
19 M28 X 1 - 6H 1.516 (38.5) 1.410 (35.8) 1.52 (38.6) .615 (15.6) 1.45 (36.8) 1.375 (34.9)
21 M31 X 1 - 6H 1.642 (41.7) 1.510 (38.4) 1.64 (41.7) .698 (17.7) 1.54 (39.1) 1.500 (38.1)
23 M34 X 1 - 6H 1.768 (44.9) 1.660 (42.2) 1.77 (45.0) .700 (17.8) 1.62 (41.1) 1.625 (41.3)
25 M37 X 1 - 6H 1.890 (48.0) 1.760 (44.7) 1.89 (48.0) .850 (21.6) 1.69 (42.9) 1.750 (44.5)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is measured with saddle bars closed and bottomed on clamp ears.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic Part Number
M85049/91 = Straight
M85049/92 = 90°
M85049/92 N 11 T
Shell Size
– = Detented
N = Non-Detented
Material and Finish Designator
J = Composite (Conductive), Cadmium Olive Drab
over Electroless Nickel
M = Composite (Conductive) Electroless Nickel
T = Composite (Non-Conductive) without Plating
XC = Composite (Conductive) Nickel Fluorocarbon Polymer
YC = Composite (Conductive) Pure Dense Electrodeposited Aluminum
ZC = Composite (Conductive) Zinc-Nickel, Black
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-104
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/93
Banding Split-Ring
Basic
Part Number
M85049/93 -10
Dash No.
TABLE I: Reference for Connector Shell Size
Dash No. Ø A Ø B
±.010 (0.3) ±.030 (0.8)
04 .25 (6.4) .36 (9.1)
06 .38 (9.7) .49 (12.4)
08 .50 (12.7) .61 (15.5)
10 .63 (16.0) .74 (18.8)
12 .75 (19.1) .86 (21.8)
14 .88 (22.4) .99 (25.1)
16 1.00 (25.4) 1.11 (28.2)
18 1.13 (28.7) 1.24 (31.5)
20 1.25 (31.8) 1.36 (34.5)
22 1.38 (35.1) 1.49 (37.8)
24 1.50 (38.1) 1.61 (40.9)
26 1.63 (41.4) 1.74 (44.2)
28 1.75 (44.5) 1.86 (47.2)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Use with Glenair Banding Backshells and Braid Socks. Consult factory for specic
application part numbers.
4. Metric dimensions (mm) are in parentheses.
5. Material - high grade engineering thermoplastic.
Shrink Sleeve or
Shrink Boot
Shield
Sock
Solder
Sleeve
Split Ring Shield Pig Tail
or Drain Wire
SAMPLE APPLICATION
AS85049/128
Band AS85049/128
Band
B
.50
(12.7)
Min.
A
.88 (22.4)
Max
Accomodates
AS85049/128
Band
Tape Wrap
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-105
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/94
Mounting Flange, Full Perimeter
A = Primer Coat
Required
Basic
Part Number
M85049/94 -10 -A
Shell Size
TABLE I: Reference for Connector Shell Size
Shell
Size Thread
UNJC-3B AB
Max CD
Max
±.015 (.38) ±.015 (.4)
84-40 .594 (15.1) .900 (22.9) .570 (14.5) .166 (4.2)
10 4-40 .719 (18.3) 1.034 (26.3) .720 (18.3) .166 (4.2)
12 4-40 .812 (20.6) 1.119 (28.4) .845 (21.5) .166 (4.2)
14 4-40 .906 (23.0) 1.213 (30.8) .975 (24.8) .166 (4.2)
16 4-40 .969 (24.6) 1.295 (32.9) 1.085 (27.6) .166 (4.2)
18 4-40 1.062 (27.0) 1.421 (36.1) 1.210 (30.7) .166 (4.2)
20 4-40 1.156 (29.4) 1.550 (39.4) 1.335 (33.9) .166 (4.2)
22 4-40 1.250 (31.8) 1.680 (42.7) 1.470 (37.3) .166 (4.2)
24 6-32 1.375 (34.9) 1.800 (45.7) 1.585 (40.3) .183 (4.6)
25 6-32 1.500 (38.1) 1.910 (48.5) 1.658 (42.1) .183 (4.6)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
DB
A
AB
.040 (1.02)
±.003 (0.8)
C
Nut, Self-Locking, Clinch
NASM 45938 Type, 4 Places
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-106
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/95
3/4 Perimeter Mounting Flange
A = Primer Coat
Required
Basic
Part Number
M85049/95 -10A -A
Shell Size
and Class
TABLE I: Reference for Connector Shell Size
Shell Size
& Class
Thread
UNJC-3B
A
±.005 (0.1)
B
Max
C
±.015 (0.4)
D
Max
E
±.030 (0.8)
3A 4-40 .625 15.88 .940 23.88 .641 16.3 .166 4.22 .325 8.25
7A 4-40 .719 18.26 1.034 26.26 .688 17.5 .166 4.22 .433 11.00
8A 4-40 .594 15.09 .900 22.86 .570 14.5 .166 4.22 .308 7.82
10A 4-40 .719 18.26 1.034 26.26 .720 18.3 .166 4.22 .433 11.00
10B 6-32 .812 20.62 1.202 30.53 .749 19.0 .183 4.65 .433 11.00
12A 4-40 .812 20.62 1.119 28.42 .855 21.7 .166 4.22 .530 13.46
12B 6-32 .938 23.83 1.327 33.71 .938 23.8 .183 4.65 .530 13.46
14A 4-40 .906 23.01 1.213 30.81 .984 25.0 .166 4.22 .624 15.85
14B 6-32 1.031 26.19 1.421 36.09 1.031 26.2 .183 4.65 .624 15.85
16A 4-40 .969 24.61 1.295 32.89 1.094 27.8 .166 4.22 .687 17.45
16B 6-32 1.125 28.58 1.515 38.48 1.125 28.6 .183 4.65 .687 17.45
18A 4-40 1.062 26.97 1.421 36.09 1.220 31.0 .166 4.22 .780 19.81
18B 6-32 1.203 30.56 1.593 40.46 1.234 31.3 .183 4.65 .780 19.81
19A 4-40 .906 23.01 1.207 30.66 .953 24.2 .166 4.22 .620 15.75
20A 4-40 1.156 29.36 1.550 39.37 1.345 34.2 .166 4.22 .874 22.20
20B 6-32 1.297 32.94 1.703 43.26 1.359 34.5 .183 4.65 .865 21.97
22A 4-40 1.250 31.75 1.680 42.67 1.478 37.5 .166 4.22 .968 24.59
22B 6-32 1.375 34.92 1.753 44.53 1.483 37.7 .183 4.65 .907 23.04
24A 6-32 1.500 38.10 1.906 48.41 1.560 39.6 .183 4.65 1.000 125.40
24B 6-32 1.375 34.92 1.800 45.72 1.595 40.5 .183 4.65 1.031 126.19
25A 6-32 1.500 38.10 1.906 48.41 1.658 42.1 .183 4.65 1.125 128.58
27A 4-40 .969 24.61 1.270 32.26 1.094 27.8 .166 4.22 .683 17.35
28A 6-32 1.562 39.67 2.015 51.18 1.820 46.2 .183 4.65 1.125 128.58
32A 6-32 1.750 44.45 2.327 59.11 2.062 52.4 .183 4.65 1.188 130.18
36A 6-32 1.938 49.23 2.515 63.88 2.312 58.7 .183 4.65 1.375 134.92
37A 4-40 1.187 30.15 1.515 38.48 1.281 32.5 .166 4.22 .874 22.20
61A 4-40 1.437 36.50 1.827 46.41 1.594 40.5 .166 4.22 1.062 26.97
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part
number, space permitting.
2. For complete dimensions, see the applicable Military
Specication.
3. Metric dimensions (mm) are in parentheses.
D
B
A
AB
.040 (1.02)
±.003 (0.8)
E
C
Nut, Self-Locking, Clinch
NASM 45938 Type, 4 Places
Rev. 03/22/19
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-107
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/96
Mounting Flange, 1/4 Perimeter
Dash No.
M85049/96 -10 -A
A - Primer Coat Required
Basic Number
TABLE I
Dash
No. Thread
UNJC-3B A
± .003 (0.1) B
± .015 (0.4)
C
+ .015 (.4)
- .000 (.0) D
± .030 (0.8) E
± .005 (0.1) F
(Ref) G
Max
3 4-40 .625 (15.9) .925 (23.5) .300 (7.6) .136 (3.5) .312 (7.92) .150 (3.81) .310 (7.87)
7 4-40 .719 (18.3) 1.016 (25.8) .298 (7.6) .136 (3.5) .359 (9.12) .149 (3.78) .308 (7.82)
8 4-40 .594 (15.1) .891 (22.6) .296 (7.5) .136 (3.5) .297 (7.54) .148 (3.76) .306 (7.77)
10 4-40 .719 (18.3) 1.016 (25.8) .298 (7.6) .136 (3.5) .359 (9.12) .149 (3.78) .308 (7.82)
12 4-40 .812 (20.6) 1.109 (28.2) .296 (7.5) .136 (3.5) .406 (10.31) .148 (3.76) .306 (7.77)
14 4-40 .906 (23.0) 1.203 (30.6) .296 (7.5) .136 (3.5) .453 (11.51) .148 (3.76) .306 (7.77)
16 4-40 .969 (24.6) 1.266 (32.2) .298 (7.6) .136 (3.5) .484 (12.29) .149 (3.78) .308 (7.82)
18 4-40 1.062 (27.0) 1.390 (35.3) .328 (8.3) .136 (3.5) .531 (13.49) .164 (4.17) .338 (8.59)
19 4-40 .906 (23.0) 1.203 (30.6) .296 (7.5) .136 (3.5) .453 (11.51) .148 (3.76) .306 (7.77)
20 4-40 1.156 (29.4) 1.510 (38.4) .354 (9.0) .136 (3.5) .578 (14.68) .177 (4.50) .364 (9.25)
22 4-40 1.250 (31.8) 1.640 (41.7) .390 (9.9) .136 (3.5) .625 (15.88) .195 (4.95) .400 (10.16)
24 6-32 1.375 (34.9) 1.760 (44.7) .386 (9.8) .153 (3.9) .687 (17.45) .193 (4.90) .396 (10.06)
25 6-32 1.500 (38.1) 1.859 (47.2) .358 (9.1) .153 (3.9) .750 (19.05) .179 (4.55) .368 (9.35)
27 4-40 .969 (24.6) 1.266 (32.2) .298 (7.6) .136 (3.5) .484 (12.29) .149 (3.78) .308 (7.82)
28 6-32 1.562 (39.7) 2.000 (50.8) .438 (11.1) .153 (3.9) .781 (19.84) .219 (5.56) .448 (11.38)
32 6-32 1.750 (44.5) 2.312 (58.7) .562 (14.3) .153 (3.9) .875 (22.23) .281 (7.14) .572 (14.53)
36 6-32 1.938 (49.2) 2.500 (63.5) .562 (14.3) .153 (3.9) .969 (24.61) .281 (7.14) .572 (14.53)
37 4-40 1.187 (30.1) 1.500 (38.1) .314 (8.0) .136 (3.5) .593 (15.06) .157 (3.99) .324 (8.23)
61 4-40 1.437 (36.5) 1.812 (46.0) .376 (9.6) .136 (3.5) .718 (18.24) .188 (4.78) .386 (9.80)
D
.040 (1.0)
± .003 (0.1)
Nut, Self-Locking, Clinch
MIL-N-45938 Type, 2 Places
A B
G
F
C
E
E
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-108
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/103
Composite Straight RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
Product Series and
Basic Part Number
M85049/103 -11 N
Shell Size
(Table I)
N = Non-Detented Self-Locking
(Omit for Detented Self-Locking)
(See Note 6)
CONNECTOR DESIGNATOR:
H MIL-DTL-38999 Series III and IV
EN3645
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. Glenair 600 Series backshell assembly tools are recommended
for assembly and installation.
4. Cable entry is measured with saddle bars closed and bottomed
on clamp ears.
5. For shield/splice termination use AS85049/93 split support ring.
6. Detented self-locking has a positive audible detented coupling.
7. Material/Finish:
Clamp body, coupling nut, saddles - High grade engineering
thermoplastic/N.A.
Clamp hardware - CRES/passivated, silver plated, mfg option
Anti-rotation device - Corrosion resistant material
Braid - Copper/nickel plated
Interface ring and shroud - Brass/nickel plated
Braid retention device - See Table II
E
A Thread
B
Captivated Self-Locking Telescoping
Screws & Washers - Typ
J
.25 (6.4) Max
Screw
Extension Typ
EMI Shroud F
G
D
(See Note 4)
Braid I.D.
Ref
Braided Shield
(See Note 5)
Anti-rotation Device
(See Part Number
Development)
H
0.125 (3.18) Drain Holes
(Under Coupling) 3 Min
Equally Spaced
10.00 (254.0) Min
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-109
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B B
Max C
Max
D
± .031
(0.79)
See Note 4
E
Min F
Max
G
± .030
(0.76)
H
Hex J
Min
Braid
I.D.
Ref
Screw
Size
09 M12 X 1 - 6H .858 (21.79) .98 (24.89) .265 (6.73) .229 (5.82) .939 (23.85) .375 (9.53) .750/.736
(19.05/18.69) .264 (6.71) .375 (9.53) 4-40
11 M15 X 1 - 6H .984 (24.99) 1.05 (26.67) .310 (7.87) .274 (6.96) 1.059 (26.90) .375 (9.53) .875/.860
(22.23/21.84) .390 (9.91) .375 (9.53) 4-40
13 M18 X 1 - 6H 1.157 (29.39) 1.20 (30.48) .390 (9.91) .354 (8.99) 1.199 (30.45) .406 (10.31) 1.000/.980
(25.40/24.89) .504 (12.80) .500 (12.70) 6-32
15 M22 X 1 - 6H 1.280 (32.51) 1.30 (33.02) .506 (12.85) .470 (11.94) 1.199 (30.45) .406 (10.31) 1.125/1.100
(31.75/31.09) .630 (16.00) .500 (12.70) 6-32
17 M25 X 1 - 6H 1.406 (35.71) 1.44 (36.58) .591 (15.01) .555 (14.10) 1.329 (33.76) .406 (10.31) 1.250/1.224
(31.75/31.09) .756 (19.20 .781 (19.84) 6-32
19 M28 X 1 - 6H 1.516 (38.51) 1.56 (39.62) .661 (16.79) .625 (15.88) 1.509 (38.33) .406 (10.31) 1.375/1.348
(34.93/34.24) .843 (21.41) .781 (19.84) 6-32
21 M31 X 1 - 6H 1.642 (41.71) 1.69 (42.93) .744 (18.90) .708 (17.98) 1.609 (40.87) .406 (10.31) 1.500/1.469
(38.10/37.31) .969 (24.61) 1.000 (25.40) 6-32
23 M34 X 1 - 6H 1.768 (44.91) 1.77 (44.96) .826 (20.98) .790 (20.07) 1.759 (44.68) .406 (10.31) 1.625/1.581
(41.28/40.16) 1.091 (27.71) 1.000 (25.40) 6-32
25 M37 X 1 - 6H 1.890 (48.01) 1.89 (48.01) .896 (22.76) .860 (21.84) 1.859 (47.22) .406 (10.31) 1.750/1.690
(44.45/42.93) 1.217 (30.91) 1.250 (31.75) 6-32
AS85049/103
Composite Straight RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
Table II (Manufacturer’s Option)
Material Finish
Aluminum Alloy Iridite per AMS-C-5541
Stainless Steel Passivated
Copper Tin Plate
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-110
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/104
Composite 45° RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. Glenair 600 Series backshell assembly tools are recommended
for assembly and installation.
4. Cable entry is measured with saddle bars closed and bottomed
on clamp ears.
5. For shield/splice termination use AS85049/93 split support ring.
6. Detented self-locking has a positive audible detented coupling.
7. Material/Finish:
Clamp body, coupling nut, saddles - High grade engineering
thermoplastic/N.A.
Clamp hardware - CRES/passivated, silver plated, mfg option
Anti-rotation device - Corrosion resistant material
Braid - Copper/nickel plated
Interface ring and shroud - Brass/nickel plated
Braid retention device - See Table II
Product Series and
Basic Part Number
M85049/104 -11 N
Shell Size
(Table I)
N = Non-Detented Self-Locking
(Omit for Detented Self-Locking)
(See Note 6)
A Thread
EMI
S
hroud
Anti-Rotation Device
(See Part Number
Development)
H
Ø.125 (3.18) Drain Holes
3 Min Equally Spaced
Braided Shield
(See Note 5)
Captivated Self-locking
Telescoping Screws - Typ
.25 (6.4) Max
Screw Extension, Typ
Braid I.D. Ref
JB
F
G10.00 (254.0)
Min
K
EC
D
(See Note 4)
CONNECTOR DESIGNATOR:
H MIL-DTL-38999 Series III and IV
EN3645
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-111
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B B
Max C
Max
D
± .031
(0.79)
See Note 4
E
Min F
Max
G
± .030
(0.76)
H
Hex J
Min K
Max
Braid
I.D.
Ref
Screw
Size
09 M12 X 1 - 6H .858 (21.79) .98 (24.89) .265 (6.73) .229 (5.82) 1.388 (35.26) .375 (9.53) .750/.736
(19.05/18.69) .264 (6.71) .901 (22.89) .375 (9.53) 4-40
11 M15 X 1 - 6H .984 (24.99) 1.05 (26.67) .310 (7.87) .274 (6.96) 1.428 (36.27) .375 (9.53) .875/.860
(22.23/21.84) .390 (9.91) .964 (24.39) .375 (9.53) 4-40
13 M18 X 1 - 6H 1.157 (29.39) 1.20 (30.48) .390 (9.91) .354 (8.99) 1.498 (38.05) .406 (10.31) 1.000/.980
(25.40/24.89) .504 (12.80) 1.050 (26.67) .500 (12.70) 6-32
15 M22 X 1 - 6H 1.280 (32.51) 1.30 (33.02) .506 (12.85) .470 (11.94) 1.548 (39.32) .406 (10.31) 1.125/1.100
(31.75/31.09) .630 (16.00) 1.112 (28.24) .500 (12.70) 6-32
17 M25 X 1 - 6H 1.406 (35.71) 1.44 (36.58) .591 (15.01) .555 (14.10) 1.648 (41.86) .406 (10.31) 1.250/1.224
(31.75/31.09) .756 (19.20 1.175 (29.85) .781 (19.84) 6-32
19 M28 X 1 - 6H 1.516 (38.51) 1.56 (39.62) .661 (16.79) .625 (15.88) 1.768 (44.91) .406 (10.31) 1.375/1.348
(34.93/34.24) .843 (21.41) 1.230 (31.24) .781 (19.84) 6-32
21 M31 X 1 - 6H 1.642 (41.71) 1.69 (42.93) .744 (18.90) .708 (17.98) 1.808 (45.92) .406 (10.31) 1.500/1.469
(38.10/37.31) .969 (24.61) 1.293 (32.84) 1.000 (25.40) 6-32
23 M34 X 1 - 6H 1.768 (44.91) 1.77 (44.96) .826 (20.98) .790 (20.07) 1.858 (47.19) .406 (10.31) 1.625/1.581
(41.28/40.16) 1.091 (27.71) 1.365 (34.67) 1.000 (25.40) 6-32
25 M37 X 1 - 6H 1.890 (48.01) 1.89 (48.01) .896 (22.76) .860 (21.84) 1.898 (48.21 .406 (10.31) 1.750/1.690
(44.45/42.93) 1.217 (30.91) 1.417 (35.99) 1.250 (31.75) 6-32
Table II (Manufacturer’s Option)
Material Finish
Aluminum Alloy Iridite per AMS-C-5541
Stainless Steel Passivated
Copper Tin Plate
AS85049/104
Composite 45° RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-112
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/105
Composite 90° RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
Product Series and
Basic Part Number
M85049/105 -11 N
Shell Size
(Table I)
N = Non-Detented Self-Locking
(Omit for Detented Self-Locking)
(See Note 6)
E
A Thread
B
Captivated Self-locking Telescoping
Screws & Washers - Typ
.25 (6.4) Max
Screw Extension
Typ
EMI Shroud
D (See Note 4)
Anti-rotation Device
(See Part Number
Development)
H
F
Ø.125 (3.18) Drain Holes
3 Min Equally Spaced
J
Braid I.D. Ref
10.00 (254.0)
Min
G K
Braided Shield
(See Note 5)
C
CONNECTOR DESIGNATOR:
H MIL-DTL-38999 Series III and IV
EN3645
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-113
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B B
Max C
Max
D
± .031
(0.79)
See Note 4
E
Min F
Max
G
± .030
(0.76)
H
Hex J
Min K
Max
Braid
I.D.
Ref
Screw
Size
09 M12 X 1 - 6H .858 (21.79) .98 (24.89) .265 (6.73) .229 (5.82) 1.128 (28.65) .375 (9.53) .750/.736
(19.05/18.69) .264 (6.71) .94 (23.88) .375 (9.53) 4-40
11 M15 X 1 - 6H .984 (24.99) 1.05 (26.67) .310 (7.87) .274 (6.96) 1.168 (29.67) .375 (9.53) .875/.860
(22.23/21.84) .390 (9.91) 1.00 (25.40) .375 (9.53) 4-40
13 M18 X 1 - 6H 1.157 (29.39) 1.20 (30.48) .390 (9.91) .354 (8.99) 1.248 (31.70) .406 (10.31) 1.000/.980
(25.40/24.89) .504 (12.80) 1.12 (28.45) .500 (12.70) 6-32
15 M22 X 1 - 6H 1.280 (32.51) 1.30 (33.02) .506 (12.85) .470 (11.94) 1.368 (34.75) .406 (10.31) 1.125/1.100
(31.75/31.09) .630 (16.00) 1.19 (30.23) .500 (12.70) 6-32
17 M25 X 1 - 6H 1.406 (35.71) 1.44 (36.58) .591 (15.01) .555 (14.10) 1.448 (36.78) .406 (10.31) 1.250/1.224
(31.75/31.09) .756 (19.20 1.37 (34.80) .781 (19.84) 6-32
19 M28 X 1 - 6H 1.516 (38.51) 1.56 (39.62) .661 (16.79) .625 (15.88) 1.528 (38.81) .406 (10.31) 1.375/1.348
(34.93/34.24) .843 (21.41) 1.44 (36.58) .781 (19.84) 6-32
21 M31 X 1 - 6H 1.642 (41.71) 1.69 (42.93) .744 (18.90) .708 (17.98) 1.648 (41.86) .406 (10.31) 1.500/1.469
(38.10/37.31) .969 (24.61) 1.56 (39.62) 1.000 (25.40) 6-32
23 M34 X 1 - 6H 1.768 (44.91) 1.77 (44.96) .826 (20.98) .790 (20.07) 1.688 (42.88) .406 (10.31) 1.625/1.581
(41.28/40.16) 1.091 (27.71) 1.69 (42.93) 1.000 (25.40) 6-32
25 M37 X 1 - 6H 1.890 (48.01) 1.89 (48.01) .896 (22.76) .860 (21.84) 1.758 (44.65) .406 (10.31) 1.750/1.690
(44.45/42.93) 1.217 (30.91) 1.81 (45.97) 1.250 (31.75) 6-32
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. Glenair 600 Series backshell assembly tools are recommended
for assembly and installation.
4. Cable entry is measured with saddle bars closed and bottomed
on clamp ears.
5. For shield/splice termination use AS85049/93 split support ring.
6. Detented self-locking has a positive audible detented coupling.
7. Material/Finish:
Clamp body, coupling nut, saddles - High grade engineering
thermoplastic/N.A.
Clamp hardware - CRES/passivated, silver plated, mfg option
Anti-rotation device - Corrosion resistant material
Braid - Copper/nickel plated
Interface ring and shroud - Brass/nickel plated
Braid retention device - See Table II
Table II (Manufacturer’s Option)
Material Finish
Aluminum Alloy Iridite per AMS-C-5541
Stainless Steel Passivated
Copper Tin Plate
AS85049/105
Composite 90° RFI/EMI Shield-Sock Adapter
with Detented or Non-Detented Self-Locking Coupling Nut
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-114
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/109
Straight RFI/EMI Shield-Sock Metal
Shrink Boot Adapter with Optional Detented or Non-Detented
Self-Locking or Non-Self-Locking Coupling Nut
Product Series and
Basic Part Number
M85049/109 S 10 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II) Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
BZ
Y
W
See Note 9
±.50 (12.7)
Length
See Note 5
Single Layer Shield
See Note 8
Knurl Style Mfr
Option - Typ
Marking Location
Optional
A Thread
.140 (3.56)
.130 (3.30)
(Ref)
.075 (1.9)
Coupling Nut
Adapter Body
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3
EN 2997, EN 3646
ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2
PATT 602
1.19 (30.2)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-115
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Shell Size, Entry Size, Thread and Dimensions
Accessory
Shell Size
Code
Allowable
Cable
Entry Size
Shell Size
AS81703, Series III
(Ref)
Shell Size
MIL-DTL-26482, Series II
MIL-DTL-83723, Series III
(Ref)
Shell Size
MIL-DTL-5015,
Series I and II
(Ref)
A
Thread Class 2B
B Max
Diameter
03 01 3 - - 9/16-24 UNEF .855 (22.48)
08 01 - 8 8S 1/2-20 UNF .885 (22.48)
10 01-03 - 10 10S & 10SL 5/8-24 UNEF 1.010 (25.65)
12 01-05 7 12 12S & 12 3/4-20 UNEF 1.135 (28.83)
14 02-06 12 14 14S & 14 7.8-20 UNEF 1.260 (32.00)
16 04-08 19 16 16S & 16 1-20 UNEF 1.385 (35.18)
18 05-09 27 18 18 1 1/16-18 UNEF 1.510 (38.35)
20 07-11 37 20 20 1 3/16-18 UNEF 1.635 (41.53)
22 09-13 - 22 22 1 5/16-18 UNEF 1.760 (44.70)
24 11-14 - 24 24 1 7/16-18 UNEF 1.885 (47.88)
28 14-16 - - 28 1 3/4-18 UNS 2.135 (54.23)
32 16-17 - - 32 2-18 UNS 2.395 (60.83)
36 17-19 - - 36 2 1/4-16 UN 2.635 (66.93)
40 19-21 - - 40 2 1/2-16 UN 2.885 (73.28)
44 21-23 - - 44 2 3/4-16 UN 3.135 (76.63)
48 23-25 - - 48 3-16 UN 3.385 (85.98)
61 12-14 61 - - 1 1/2-18 UNEF 1.885 (47.88)
APPLICATION NOTES
1. Metric equivalents are given for general information only and
are based on 1.000 inch (25.40 mm).
2. Dimensions are in inches and apply after plating. Accessory
conguration is optional within the specied dimension
envelope.
3. Adapter length is measured from the bottom of the accessory
teeth to the adapter that is covered by the braid, The adapter
surface under the braid shall be ribbed knurled or have a
surface roughness of .125 R minimum in accordance with ANSI
B46.1.
4. Pig tail terminated braid material shall be in accordance with
TableIV. Braid length is dened by Note 1 as shown in the part
or indentifying number (PIN).
5. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimension (See Table II) provided
the band does not interfere with boot attachment, band material
shall be specied as in Table V.
6. Shrink boot (when required) shall be as specied in AS5258.
7. Termination of rthe accessory shield with harness shield
may be performed with a AS85049/93 shield support ring or
similar split ring accessory types.
8. Three (3) holes equally spaced shall be provided and
accommodate .020 (.51) maximum safety wire for the non-
self-locking coupling conguration.
9. Drain holes will be provided with a.125 (3.2 mm) diameter,
4 places equally spaces (optional, see part number
development).
10. Material/Finish:
Adapter, coupling nut - Al alloy/See Table III
Band - See Table V, manufacturer’s option
Braid - Copper/See Table IV
TABLE II: Entry Size
and Dimensions
Entry
Size W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.120 (28.4)
10 .812 (20.6) .069 (1.75) 1.200 (30.5)
11 .875 (22.2) .069 (1.75) 1.270 (32.3)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.370 (34.8)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
15 1,250 (31.8) .069 (1.75) 1.600 (40.6)
16 1.375 (34.9) .069 (1.75) 1.710 (43.4)
17 1.500 (38.1) .086 (2.18) 1.840 (46.7)
18 1.625 (41.3) .086 (2.18) 2.000 (50.8)
19 1.750 (44.5) .086 (2.18) 2.120 (53.8)
20 1.875 (47.6) .086 (2.18) 2.270 (57.7)
21 2.000 (50.8) .086 (2.18) 2.440 (62.0)
22 2.125 (54.0) .086 (2.18) 2.600 (66.0)
23 2.250 (57.2) .086 (2.18) 2.750 (69.9)
24 2.375 (60.3) .086 (2.18) 2.900 (73.7)
25 2.500 (63.5) .086 (2.18) 3.060 (77.7)
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCadmium/Olive Drab over Electroless
Nickel (1000 Hour Salt Spray)
XNickel Flurocarbon Polymer
ZZinc Nickel
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
AS85049/109
Straight RFI/EMI Shield-Sock Metal
Shrink Boot Adapter with Optional Detented or Non-Detented
Self-Locking or Non-Self-Locking Coupling Nut
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-116
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/111
90° RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
Product Series and
Specication Sheet
M85049/111 S 10 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II) Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
TABLE II: Entry Size
and Dimensions
Entry
Size W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.120 (28.4)
10 .812 (20.6) .069 (1.75) 1.200 (30.5)
11 .875 (22.2) .069 (1.75) 1.270 (32.3)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.370 (34.8)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
15 1,250 (31.8) .069 (1.75) 1.600 (40.6)
16 1.375 (34.9) .069 (1.75) 1.710 (43.4)
17 1.500 (38.1) .086 (2.18) 1.840 (46.7)
18 1.625 (41.3) .086 (2.18) 2.000 (50.8)
19 1.750 (44.5) .086 (2.18) 2.120 (53.8)
20 1.875 (47.6) .086 (2.18) 2.270 (57.7)
21 2.000 (50.8) .086 (2.18) 2.440 (62.0)
22 2.125 (54.0) .086 (2.18) 2.600 (66.0)
23 2.250 (57.2) .086 (2.18) 2.750 (69.9)
24 2.375 (60.3) .086 (2.18) 2.900 (73.7)
25 2.500 (63.5) .086 (2.18) 3.060 (77.7)
B
Z
Y
W
See Note 9
Length
±.50 (12.7)
See Note 5
Single Layer Shield
See Note 8
Knurl Style Mfr
Option - Typ
Marking Location
Optional
A Thread
.140 (3.56)
.130 (3.30)
(Ref)
.075
(1.9)
Coupling Nut
Adapter Body
J Max
H
Configuration
Optional
CONNECTOR DESIGNATOR:
A
AS50151 Series AS34001
MIL-DTL-26482 Series II
AS81703 Series III
MIL-DTL-83723 Series I & III
40M39569, DEF 5326-3
EN 2997, EN 3646
ESC 10, ESC 11, LN 29504
NFC93422 Series HE302
PAN 6432-1, PAN 6432-2
PATT 602
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-117
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/111
90° RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
TABLE I: Shell Size, Entry Size, Thread and Dimensions
Accessory
Shell Size
Code
Allowable
Cable
Entry Size
Shell Size
AS81703, Series III
(Ref)
Shell Size
MIL-DTL-26482, Series II
MIL-DTL-83723, Series III
(Ref)
Shell Size
MIL-DTL-5015,
Series I and II
(Ref)
A
Thread Class 2B
B Max
Diameter
H
Max
J
Max
03 01 3 - - 9/16-24 UNEF .855 (22.48) 1.730 (43.94) 1.120 (28.45)
08 01 - 8 8S 1/2-20 UNF .885 (22.48) 1.730 (43.94) 1.120 (28.45)
10 01-03 - 10 10S & 10SL 5/8-24 UNEF 1.010 (25.65) 1.850 (46.99) 1.250 (31.75)
12 01-05 7 12 12S & 12 3/4-20 UNEF 1.135 (28.83) 1.870 (47.50) 1.380 (35.05)
14 02-06 12 14 14S & 14 7.8-20 UNEF 1.260 (32.00) 1.940 (49.28) 1.440 (36.58)
16 04-08 19 16 16S & 16 1-20 UNEF 1.385 (35.18) 2.030 (51.56) 1.560 (39.62)
18 05-09 27 18 18 1 1/16-18 UNEF 1.510 (38.35) 2.200 (55.88) 1.750 (44.45)
20 07-11 37 20 20 1 3/16-18 UNEF 1.635 (41.53) 2.200 (55.88) 1.750 (44.45)
22 09-13 - 22 22 1 5/16-18 UNEF 1.760 (44.70) 2.310 (58.67) 2.000 (50.80)
24 11-14 - 24 24 1 7/16-18 UNEF 1.885 (47.88) 2.310 (58.67) 2.000 (50.80)
28 14-16 - - 28 1 3/4-18 UNS 2.135 (54.23) 2.480 (62.99) 2.250 (57.15)
32 16-17 - - 32 2-18 UNS 2.395 (60.83) 2.730 (69.34) 2.750 (69.85)
36 17-19 - - 36 2 1/4-16 UN 2.635 (66.93) 2.730 (69.34) 3.125 (79.38)
40 19-21 - - 40 2 1/2-16 UN 2.885 (73.28) 2.880 (73.15) 4.125 (104.77)
44 21-23 - - 44 2 3/4-16 UN 3.135 (76.63) 3.000 (76.20) 4.125 (104.77)
48 23-25 - - 48 3-16 UN 3.385 (85.98) 3.120 (79.25) 4.125 (104.77)
61 12-14 61 - - 1 1/2-18 UNEF 1.885 (47.88) 2.380 (60.45) 2.250 (57.15)
APPLICATION NOTES
1. Metric equivalents are given for general information only and
are based on 1.000 inch (25.40 mm).
2. Dimensions are in inches and apply after plating. Accessory
conguration is optional within the specied dimension
envelope.
3. Adapter length is measured from the bottom of the accessory
teeth to the adapter that is covered by the braid, The adapter
surface under the braid shall be ribbed knurled or have a
surface roughness of .125 R minimum in accordance with ANSI
B46.1.
4. Pig tail terminated braid material shall be in accordance with
TableIV. Braid length is dened by Note 1 as shown in the part
or indentifying number (PIN).
5. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimension (See Table II) provided
the band does not interfere with boot attachment, band material
shall be specied as in Table V.
6. Shrink boot (when required) shall be as specied in AS5258.
7. Termination of rthe accessory shield with harness shield
may be performed with a AS85049/93 shield support ring or
similar split ring accessory types.
8. Three (3) holes equally spaced shall be provided and
accommodate .020 (.51) maximum safety wire for the non-
self-locking coupling conguration.
9. Drain holes will be provided with a.125 (3.2 mm) diameter,
4 places equally spaces (optional, see part number
development).
10. Material/Finish:
Adapter, coupling nut - Al alloy/See Table III
Band - See Table V, manufacturer’s option
Braid - Copper/See Table IV
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCadmium/Olive Drab over Electroless
Nickel (1000 Hour Salt Spray)
XNickel Flurocarbon Polymer
ZZinc Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-118
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/112
Straight RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
Product Series and
Specication Sheet
M85049/112 S 10 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II) Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
Coupling Nut
BZ
Y
W
See Note 9
±.50 (12.7)
Length
See Note 5
Single Layer Shield
See Note 8
Knurl Style Mfr
Option - Typ
Marking Location
Optional
A Thread
.140 (3.56)
.130 (3.30)
(Ref)
.075 (1.9)
O-Ring
Adapter Body
1.19 (30.2) Max
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-119
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/112
Straight RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
APPLICATION NOTES
1. Metric equivalents are given for general information only and
are based on 1.000 inch (25.40 mm).
2. Dimensions are in inches and apply after plating. Accessory
conguration is optional within the specied dimension
envelope.
3. Adapter length is measured from the bottom of the accessory
teeth to the adapter that is covered by the braid, The adapter
surface under the braid shall be ribbed knurled or have a
surface roughness of .125 R minimum in accordance with ANSI
B46.1.
4. Pig tail terminated braid material shall be in accordance with
TableIV. Braid length is dened by Note 1 as shown in the part
or indentifying number (PIN).
5. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimension (See Table II) provided
the band does not interfere with boot attachment, band material
shall be specied as in Table V.
6. Shrink boot (when required) shall be as specied in AS5258.
7. Termination of the accessory shield with harness shield
may be performed with a AS85049/93 shield support ring or
similar split ring accessory types.
8. Three (3) holes equally spaced shall be provided and
accommodate .020 (.51) maximum safety wire for the non-
self-locking coupling conguration.
9. Drain holes will be provided with a.125 (3.2 mm) diameter,
4 places equally spaces (optional, see part number
development). O-Ring not required when drain hole option is
specied.
10. Material/Finish:
Adapter, coupling nut - Al alloy/See Table III
Band - See Table V, manufacturer’s option
Braid - Copper/See Table IV
TABLE I: Shell Size, Entry Size, Thread and Dimensions
Accessory
Shell Size
Code
Series I
Shell Size
(Ref)
Series II
Shell Size
(Ref)
A
Thread Class 2B
B Max
Diameter
Allowable
Cable
Entry Size
08 9 8 7/16-28 UNEF .858 (21.79) 01
10 11 10 9/16-24 UNEF .984 (24.99) 01-03
12 13 12 11/16-24 UNEF 1.157 (29.39) 01-05
14 15 14 13/16-20 UNEF 1.279 (32.49) 03-07
16 17 16 15/16-20 UNEF 1.406 (35.71) 05-09
18 19 18 1 1/16-18 UNEF 1.516 (38.51) 06-10
20 21 20 1 3/16-18 UNEF 1.642 (41.71) 08-12
22 23 22 1 5/16-18 UNEF 1.768 (44.91) 09-13
24 25 24 1 7/16-18 UNEF 1.889 (47.98) 10-14
TABLE II: Entry Size
and Dimensions
Entry
Size W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
Z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.120 (28.4)
10 .812 (20.6) .069 (1.75) 1.200 (30.5)
11 .875 (22.2) .069 (1.75) 1.270 (32.3)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.370 (34.8)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCadmium/Olive Drab over Electroless
Nickel (1000 Hour Salt Spray)
XNickel Flurocarbon Polymer
ZZinc Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-120
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/114
90° RFI/EMI Shield-Sock Shrink Boot Adapter
with Detented or Non-Detented Self-Locking
or Non Self-Locking Coupling Nut
Product Series and
Specication Sheet
M85049/114 S 10 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II) Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
TABLE II: Entry Size
and Dimensions
Entry
Size W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
Z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.120 (28.4)
10 .812 (20.6) .069 (1.75) 1.200 (30.5)
11 .875 (22.2) .069 (1.75) 1.270 (32.3)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.370 (34.8)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
Elbow Body
Configuration
Optional
H
J
O-Ring
.075 (1.9)
(Ref)
.140 (3.56)
.130 (3.30)
A Thread
Marking Location
Optional
Knurl Style Mfr
Option - Typ
See Note 8
Single Layer Shield
See Note 5
Length
±.50 (12.7)
See Note 9
W
Y
Z
B
Coupling Nut
CONNECTOR DESIGNATOR:
F
MIL-DTL-38999 Series I & II
40M38277, PAN 6433-1
PATT 614, PATT 616
NFC93422 Series HE308 &
HE309
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-121
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
APPLICATION NOTES
1. Metric equivalents are given for general information only and
are based on 1.000 inch (25.40 mm).
2. Dimensions are in inches and apply after plating. Accessory
conguration is optional within the specied dimension
envelope.
3. Adapter length is measured from the bottom of the accessory
teeth to the adapter that is covered by the braid, The adapter
surface under the braid shall be ribbed knurled or have a
surface roughness of .125 R minimum in accordance with ANSI
B46.1.
4. Pig tail terminated braid material shall be in accordance with
Table IV. Braid length is dened by Note 1 as shown in the part
or indentifying number (PIN).
5. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimension (See Table II) provided
the band does not interfere with boot attachment, band material
shall be specied as in Table V.
6. Shrink boot (when required) shall be as specied in AS5258.
7. Termination of rthe accessory shield with harness shield may
be performed with a AS85049/93 shield support ring or similar
split ring accessory types.
8. Three (3) holes equally spaced shall be provided and
accommodate .020 (.51) maximum safety wire for the non-self-
locking coupling conguration.
9. Drain holes will be provided with a.125 (3.2 mm) diameter,
4 places equally spaces (optional, see part number
development). O-Ring not required when drain hole option is
specied.
10. Material/Finish:
Adapter, coupling nut - Al alloy/See Table III
Band - See Table V, manufacturer’s option
Braid - Copper/See Table IV
TABLE I: Shell Size, Entry Size, Thread and Dimensions
Accessory
Shell Size
Code
Series I
Shell Size
(Ref)
Series II
Shell Size
(Ref)
A
Thread Class 2B
B Max
Diameter
H
Max
J
Max
Allowable
Cable
Entry Size
08 9 8 7/16-28 UNEF .858 (21.79) 1.730 (43.94) 1.070 (27.18) 01
10 11 10 9/16-24 UNEF .984 (24.99) 1.850 (46.99) 1.190 (30.23) 01-03
12 13 12 11/16-24 UNEF 1.157 (29.39) 1.870 (47.50) 1.320 (33.53) 01-05
14 15 14 13/16-20 UNEF 1.279 (32.49) 1.940 (49.28) 1.440 (36.58) 03-07
16 17 16 15/16-20 UNEF 1.406 (35.71) 2.030 (51.56) 1.570 (39.88) 05-09
18 19 18 1 1/16-18 UNEF 1.516 (38.51) 2.200 (55.88) 1.750 (44.45) 06-10
20 21 20 1 3/16-18 UNEF 1.642 (41.71) 2.200 (55.88) 1.750 (44.45) 08-12
22 23 22 1 5/16-18 UNEF 1.768 (44.91) 2.310 (58.67) 2.000 (50.80) 09-13
24 25 24 1 7/16-18 UNEF 1.889 (47.98) 2.310 (58.67) 2.000 (50.80) 10-14
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCadmium/Olive Drab over Electroless
Nickel (1000 Hour Salt Spray)
XNickel Flurocarbon Polymer
ZZinc Nickel
AS85049/114
90° RFI/EMI Shield-Sock Shrink Boot Adapter
with Detented or Non-Detented Self-Locking
or Non Self-Locking Coupling Nut
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-122
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/115
Straight RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
Product Series and
Basic Part Number
M85049/115 S 11 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II) Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
A Thread
Knurl Style Mfr
Option - Typ
Wire Holes
(See Note 5)
±.50 (12.7)
Drain Holes
(See Note 6)
Coupling Nut
1.32 (33.5) Max
Adapter Body
O-Ring
(See Note 6)
.075 (1.9) Ref
.140 (3.56)
.130 (3.30)
Single Layer Shield
Termination Band (See Note 3)
Length
W
Y
Z
B
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-123
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
AS85049/115
Straight RFI/EMI Shield-Sock Shrink Boot Adapter
with Optional Self-Locking Coupling Nut
APPLICATION NOTES
1. Assembly identication with manufactuer’s name and part
number, space permitting.
2. Metric equivalents are given for general information only and
are based on 1.00 inch = 25.4 mm.
3. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimensions (see Table II) provided
the band does not interfere with boot attachment. Band material
shall be as specied in Table V.
4. Termination of the accessory shield with harness shield may be
performed with a GS85049/93 shield support ring or similar split
ring accessory types.
5. Three (3) holes equally spaced shall be provided and
accommodate .020 (0.51) maximum safety wire for the non-
self-locking coupling conguration.
6. .125 (3.2 mm) diameter drain holes will be provided, 4 places,
equally spaced (Optional, see part number development).
O-Ring not required when drain hole option is specied.
7. Material/Finish:
Adapter, coupling nut - Al alloy/see Table III.
Termination band - See Table V (manufacturer’s option).
Braid - Copper/see Table IV.
O-Ring - Silicone/N.A.
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
TABLE II: Entry Size
and Dimensions
Entry
Size W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
Z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.120 (28.4)
10 .812 (20.6) .069 (1.75) 1.200 (30.5)
11 .875 (22.2) .069 (1.75) 1.270 (32.3)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.370 (34.8)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
TABLE I: Shell Size
and Dimensions
Shell
Size A Thread
Class 2B B Max
Diameter
Allowable
Cable
Entry Size
09 M12 X 1 - 6H .858 (21.79) 01
11 M15 X 1 - 6H .984 (24.99) 01-03
13 M18 X 1 - 6H 1.157 (29.39) 01-05
15 M22 X 1 - 6H 1.279 (32.49) 03-07
17 M25 X 1 - 6H 1.406 (35.71) 05-09
19 M28 X 1 - 6H 1.516 (38.51) 06-10
21 M31 X 1 - 6H 1.642 (41.71) 08-12
23 M34 X 1 - 6H 1.768 (44.91) 09-13
25 M37 X 1 - 6H 1.889 (47.98) 10-14
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCadmium/Olive Drab over Electroless
Nickel (1000 Hour Salt Spray)
XNickel Flurocarbon Polymer
ZZinc Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-124
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
Product Series and
Specication Sheet
M85049/117 S 11 T W 03 -6 D
Shell Size
(Table I)
S = Detented, Self-Locking
– = Non-Self-Locking (Use Dash)
N = Non-Detented, Self-Locking
Shield Finish
(Table IV)
Finish
(Table III)
Entry Size
(Table II)
Drain Hole
(Omit for None)
Braid Length
1 Inch Increments,
6” Min., 18” Max
TABLE II: Entry Size
and Dimensions
Entry
Size
W
± .020 (.51)
Y
+.008 (.20)
-.000 (.00)
Z
Max
01 .250 (6.4) .044 (1.12) .560 (14.2)
02 .312 (7.9) .044 (1.12) .630 (16.0)
03 .375 (9.5) .044 (1.12) .690 (17.5)
04 .438 (11.1) .044 (1.12) .750 (19.1)
05 .500 (12.7) .044 (1.12) .820 (20.8)
06 .562 (14.3) .044 (1.12) .890 (22.6)
07 .625 (15.9) .044 (1.12) .950 (24.1)
08 .688 (17.5) .044 (1.12) 1.020 (25.9)
09 .750 (19.1) .069 (1.75) 1.070 (27.2)
10 .812 (20.6) .069 (1.75) 1.130 (28.7)
11 .875 (22.2) .069 (1.75) 1.190 (30.2)
12 .938 (23.8) .069 (1.75) 1.260 (32.0)
13 1.000 (25.4) .069 (1.75) 1.320 (33.5)
14 1.125 (28.6) .069 (1.75) 1.470 (37.3)
Elbow Body
Configuration
Optional
H
J
O-Ring
See Note 6
.075 (1.9)
(Ref)
.140 (3.56)
.130 (3.30)
A Thread
Marking Location
Optional
Knurl Style Mfr
Option - Typ
Wire Holes
See Note 5
Single Layer Shield
Termination Band
See Note 4
Length
±.50 (12.7)
Drain Holes
See Note 6
W
Y
Z
B
Coupling Nut
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III and IV
EN3645
AS85049/117
90° RFI/EMI Shield-Sock Shrink Boot Adapter
With Optional Self-Locking Coupling Nut
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-125
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
TABLE I: Shell Size, Entry Size, Thread and Dimensions
Accessory
Shell Size
Code
A
ISO Metric
B Max
Diameter
H
Max
J
Max
Allowable
Cable
Entry Size
9M12 x 1 - 6H .858 (21.79) 1.730 (43.94) .875 (22.23) 01
11 M15 x 1 - 6H .984 (24.99) 1.850 (46.99) 1.000 (25.40) 01-03
13 M18 x 1 - 6H 1.157 (29.39) 1.870 (47.50) 1.125 (28.58) 01-05
15 M22 x 1 - 6H 1.279 (32.49) 1.940 (49.28) 1.312 (33.32) 03-07
17 M25 x 1 - 6H 1.406 (35.71) 2.030 (51.56) 1.500 (38.10) 05-09
19 M28 x 1 - 6H 1.516 (38.51) 2.200 (55.88) 1.750 (44.45) 06-10
21 M31 x 1 - 6H 1.642 (41.71) 2.200 (55.88) 1.750 (44.45) 08-12
23 M34 x 1 - 6H 1.768 (44.91) 2.310 (58.67) 2.000 (50.80) 09-13
25 M37 x 1 - 6H 1.889 (47.98) 2.310 (58.67) 2.000 (50.80) 10-14
Table V: (Manufacturer’s Option)
Material Finish
Copper Tin Plate
Stainless Steel Passivated
Table IV: Symbol and Finish
Symbol Finish
KNickel Plate
TTin Plate
Table III: Symbol and Finish
Symbol Finish
NElectroless Nickel
WCad/O.D. over electroless nickel
(1000 hour salt spray)
ZBlack zinc nickel (1000 hour salt spray)
AS85049/117
90° RFI/EMI Shield-Sock Shrink Boot Adapter
With Optional Self-Locking Coupling Nut
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number,
space permitting.
2. With Optional Self-Locking Coupling Nut Metric equivalents are
given for general information only and are based on 1.000 inch
(25.40 mm).
3. Termination band conguration is not controlled. Band with
buckle may exceed the “Z” dimension (See Table II) provided
the band does not interfere with boot attachment, band material
shall be specied as in Table V.
4. Termination of rthe accessory shield with harness shield may be
performed with a AS85049/93 shield support ring or similar split
ring accessory types.
5. Three (3) holes equally spaced shall be provided and
accommodate .020 (.51) maximum safety wire for the non-self-
locking coupling conguration.
6. Drain holes will be provided with a.125 (3.2 mm) diameter,
4 places equally spaces (optional, see part number
development). O-Ring not required when drain hole option is
specied.
7. Material/Finish:
Adapter, coupling nut - Al alloy/See Table III
Band - See Table V, manufacturer’s option
Braid - Copper/See Table IV
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-124
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/118
Straight Strain Relief
Self-Locking or Non-Self-Locking
CONNECTOR DESIGNATOR:
AAS5015 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
SAE-AS1703 Crimp Series III,
MIL-DTL-83723 Series I & III
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
Coupling Nut
G
F
E
A Thread
Knurl Style
Optional H
C
See Note 4 Screw
Captive
Self-locking Nut
Typical
.06/.25 (1.52/6.35)
Screw Extension
D
B
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Product Series and
Basic Part Number M85049/118 S 08 W
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = Stainless Steel, Passivate
W = Aluminum, Cadmium, Olive Drab
X = Aluminum, Nickel Fluorocarbon Polymer
Y = Aluminum, Pure Dense Electrodeposited Aluminum
Z = Aluminum, Zinc-Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-125
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Dash Number, Shell Size, Thread and Dimensions (Continued Below)
Dash
No.
Screw
Size
MIL-DTL-83723
Series III
MIL-DTL-5015
MS3400 Series
AS81703
Series III
MIL-DTL-26482
Series II
A Thread
Class 2B
B Dia
Max
C Dim
± .031 (0.8)
D
Min
E Max
Length
03 4-40 –– –– 3 –– 9/16-24 UNEF .95 (24.1) .219 (5.6) .22 (5.6) 1.14 (29.0)
08 4-40 8 8S –– 8 1/2-20 UNF .89 (22.6) .219 (5.6) .22 (5.6) 1.14 (29.0)
10 4-40 10 10S, 10SL –– 10 5/8-20 UNEF 1.01 (25.7) .264 (6.7) .27 (6.9) 1.25 (31.8)
12 4-40 12 12, 12S 7 12 3/4-20 UNEF 1.14 (29.0) .344 (8.7) .35 (8.9) 1.38 (35.1)
14 4-40 14 14.14S 12 14 7/8-20 UNEF 1.26 (32.0) .460 (11.7) .47 (11.9) 1.38 (35.1)
16 4-40 16 16, 16S 19 16 1-20 UNEF 1.39 (35.3) .545 (13.8) .55 (14.0) 1.50 (38.1)
18 6-32 18 18 27 18 1 1/16-18 UNEF 1.51 (38.4) .615 (15.6) .62 (15.7) 1.75 (44.5)
20 6-32 20 20 37 20 1 3/16-18 UNEF 1.64 (41.7) .698 (17.7) .70 (17.8) 1.88 (47.8)
22 6-32 22 22 –– 24 1 5/16-18 UNEF 1.176 (44.7) .780 (19.8) .78 (19.8) 2.00 (50.8)
24 8-32 24 24 –– –– 1 7/16-18 UNEF 1.89 (48.0) .850 (21.6) .85 (21.6) 2.13 (54.1)
28 8-32 –– 28 –– –– 1 3/4-18 UNS 2.14 (54.4) .950 (24.1) .95 (24.1) 2.56 (65.0)
32 8-32 –– 32 –– –– 2-18 UNS 2.40 (61.0) 1.015 (25.8) 1.02 (25.2) 2.81 (71.4)
36 8-32 –– 36 –– –– 2 1/4-16 UN 2.64 (67.1) 1.187 (30.1) 1.19 (30.2) 3.06 (77.7)
40 8-32 –– 40 –– –– 2 1/2-16 UN 2.89 (73.4) 1.220 (31.0) 1.22 (31.0) 3.16 (80.3)
44 8-32 –– 44 –– –– 2 3/4-16 UN 3.14 (79.8) 1.500 (38.1) 1.50 (38.1) 3.53 (89.7)
48 8-32 –– 48 –– –– 3-16 UN 3.39 (86.1) 1.625 (41.3) 1.63 (41.4) 3.93 (99.8)
61 8-32 –– –– 61 –– 1 1/2-18 UNEF 1.95 (49.5) .850 (21.6) .85 (21.6) 2.13 (54.1)
AS85049/118
Straight Strain Relief
Self-Locking or Non-Self-Locking
TABLE I: (Continued from Above)
Dash
No.
Screw
Size
MIL-DTL-83723
Series III
MIL-DTL-5015
MS3400 Series
AS81703
Series III
MIL-DTL-26482
Series II
F
Dim
G Dim
Max
H Dim
Max
03 4-40 –– –– 3 –– .77 (19.6)
.51 (13.0) .88 (22.4) .710 (18.00
08 4-40 8 8S –– 8 .77 (19.6)
.51 (13.0) .88 (22.4) .710 (18.00
10 4-40 10 10S, 10SL –– 10 .89 (22.6)
.64 (16.3) .94 (23.9) .710 (18.00
12 4-40 12 12, 12S 7 12 1.01 (25.7)
.76 (19.3) 1.12 (28.4) .710 (18.00
14 4-40 14 14.14S 12 14 1.01 (25.7)
.76 (19.3) 1.19 (30.3) .710 (18.00
16 4-40 16 16, 16S 19 16 1.13 (28.7)
.88 (22.4) 1.44 (36.6) .710 (18.00
18 6-32 18 18 27 18 1.38 (35.1)
1.13 (28.7) 1.56 (39.6) .710 (18.00
20 6-32 20 20 37 20 1.51 (38.4)
1.25 (31.8) 1.69 (42.9) .710 (18.00
22 6-32 22 22 –– 24 1.62 (41.1)
1.38 (35.1) 1.75 (44.5) .710 (18.00
24 8-32 24 24 –– –– 1.76 (44.7)
1.51 (38.4) 1.88 (47.8) .710 (18.00
28 8-32 –– 28 –– –– 2.03 (51.6)
1.67 (42.5) 2.12 (53.8) .890 (22.6)
32 8-32 –– 32 –– –– 2.28 (57.9)
1.87 (47.5) 2.50 (63.5) .890 (22.6)
36 8-32 –– 36 –– –– 2.53 (64.3)
2.22 (56.4) 2.62 (66.5) .890 (22.6)
40 8-32 –– 40 –– –– 2.63 (66.8)
2.41 (61.2) 2.68 (68.1) .890 (22.6)
44 8-32 –– 44 –– –– 3.00 (76.2)
2.80 (71.1) 3.00 (76.2) .890 (22.6)
48 8-32 –– 48 –– –– 3.40 (86.4)
3.20 (81.3) 3.50 (88.9) .890 (22.6)
61 8-32 –– –– 61 –– 1.76 (44.7)
1.51 (38.5) 1.88 (47.8) .710 (18.0)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-126
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/118
Straight Strain Relief
Self-Locking or Non-Self-Locking
CONNECTOR DESIGNATOR:
A
AS5015 Series AS34001 Crimp,
MIL-DTL-26482 Series II,
SAE-AS1703 Crimp Series III,
MIL-DTL-83723 Series I & III
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
Coupling Nut
G
F
E
A Thread
Knurl Style
Optional H
C
See Note 4 Screw
Captive
Self-locking Nut
Typical
.06/.25 (1.52/6.35)
Screw Extension
D
B
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Product Series and
Basic Part Number M85049/118 S 08 W
Material and Finish Designator
A = Aluminum, Black Anodize
N = Aluminum, Electroless Nickel
S = Stainless Steel, Passivate
W = Aluminum, Cadmium, Olive Drab
X = Aluminum, Nickel Fluorocarbon Polymer
Y = Aluminum, Pure Dense Electrodeposited Aluminum
Z = Aluminum, Zinc-Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-127
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
TABLE I: Dash Number, Shell Size, Thread and Dimensions (Continued Below)
Dash
No.
Screw
Size
MIL-DTL-83723
Series III
MIL-DTL-5015
MS3400 Series
AS81703
Series III
MIL-DTL-26482
Series II
A Thread
Class 2B
B Dia
Max
C Dim
± .031 (0.8)
D
Min
E Max
Length
03 4-40 –– –– 3 –– 9/16-24 UNEF .95 (24.1) .219 (5.6) .22 (5.6) 1.14 (29.0)
08 4-40 8 8S –– 8 1/2-20 UNF .89 (22.6) .219 (5.6) .22 (5.6) 1.14 (29.0)
10 4-40 10 10S, 10SL –– 10 5/8-20 UNEF 1.01 (25.7) .264 (6.7) .27 (6.9) 1.25 (31.8)
12 4-40 12 12, 12S 7 12 3/4-20 UNEF 1.14 (29.0) .344 (8.7) .35 (8.9) 1.38 (35.1)
14 4-40 14 14.14S 12 14 7/8-20 UNEF 1.26 (32.0) .460 (11.7) .47 (11.9) 1.38 (35.1)
16 4-40 16 16, 16S 19 16 1-20 UNEF 1.39 (35.3) .545 (13.8) .55 (14.0) 1.50 (38.1)
18 6-32 18 18 27 18 1 1/16-18 UNEF 1.51 (38.4) .615 (15.6) .62 (15.7) 1.75 (44.5)
20 6-32 20 20 37 20 1 3/16-18 UNEF 1.64 (41.7) .698 (17.7) .70 (17.8) 1.88 (47.8)
22 6-32 22 22 –– 22 1 5/16-18 UNEF 1.176 (44.7) .780 (19.8) .78 (19.8) 2.00 (50.8)
24 8-32 24 24 –– –– 1 7/16-18 UNEF 1.89 (48.0) .850 (21.6) .85 (21.6) 2.13 (54.1)
28 8-32 –– 28 –– –– 1 3/4-18 UNS 2.14 (54.4) .950 (24.1) .95 (24.1) 2.56 (65.0)
32 8-32 –– 32 –– –– 2-18 UNS 2.40 (61.0) 1.015 (25.8) 1.02 (25.2) 2.81 (71.4)
36 8-32 –– 36 –– –– 2 1/4-16 UN 2.64 (67.1) 1.187 (30.1) 1.19 (30.2) 3.06 (77.7)
40 8-32 –– 40 –– –– 2 1/2-16 UN 2.89 (73.4) 1.220 (31.0) 1.22 (31.0) 3.16 (80.3)
44 8-32 –– 44 –– –– 2 3/4-16 UN 3.14 (79.8) 1.500 (38.1) 1.50 (38.1) 3.53 (89.7)
48 8-32 –– 48 –– –– 3-16 UN 3.39 (86.1) 1.625 (41.3) 1.63 (41.4) 3.93 (99.8)
61 8-32 –– –– 61 –– 1 1/2-18 UNEF 1.95 (49.5) .850 (21.6) .85 (21.6) 2.13 (54.1)
AS85049/118
Straight Strain Relief
Self-Locking or Non-Self-Locking
TABLE I: (Continued from Above)
Dash
No.
Screw
Size
MIL-DTL-83723
Series III
MIL-DTL-5015
MS3400 Series
AS81703
Series III
MIL-DTL-26482
Series II
F
Dim
G Dim
Max
H Dim
Max
03 4-40 –– –– 3 –– .77 (19.6)
.51 (13.0) .88 (22.4) .710 (18.00
08 4-40 8 8S –– 8 .77 (19.6)
.51 (13.0) .88 (22.4) .710 (18.00
10 4-40 10 10S, 10SL –– 10 .89 (22.6)
.64 (16.3) .94 (23.9) .710 (18.00
12 4-40 12 12, 12S 7 12 1.01 (25.7)
.76 (19.3) 1.12 (28.4) .710 (18.00
14 4-40 14 14.14S 12 14 1.01 (25.7)
.76 (19.3) 1.19 (30.3) .710 (18.00
16 4-40 16 16, 16S 19 16 1.13 (28.7)
.88 (22.4) 1.44 (36.6) .710 (18.00
18 6-32 18 18 27 18 1.38 (35.1)
1.13 (28.7) 1.56 (39.6) .710 (18.00
20 6-32 20 20 37 20 1.51 (38.4)
1.25 (31.8) 1.69 (42.9) .710 (18.00
22 6-32 22 22 –– 24 1.62 (41.1)
1.38 (35.1) 1.75 (44.5) .710 (18.00
24 8-32 24 24 –– –– 1.76 (44.7)
1.51 (38.4) 1.88 (47.8) .710 (18.00
28 8-32 –– 28 –– –– 2.03 (51.6)
1.67 (42.5) 2.12 (53.8) .890 (22.6)
32 8-32 –– 32 –– –– 2.28 (57.9)
1.87 (47.5) 2.50 (63.5) .890 (22.6)
36 8-32 –– 36 –– –– 2.53 (64.3)
2.22 (56.4) 2.62 (66.5) .890 (22.6)
40 8-32 –– 40 –– –– 2.63 (66.8)
2.41 (61.2) 2.68 (68.1) .890 (22.6)
44 8-32 –– 44 –– –– 3.00 (76.2)
2.80 (71.1) 3.00 (76.2) .890 (22.6)
48 8-32 –– 48 –– –– 3.40 (86.4)
3.20 (81.3) 3.50 (88.9) .890 (22.6)
61 8-32 –– –– 61 –– 1.76 (44.7)
1.51 (38.5) 1.88 (47.8) .710 (18.0)
Rev. 05.15.18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-128
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/121
Straight Strain Relief
Self-Locking or Non-Self-Locking
Screw
Captive
Self-locking Nut
-typ- C
See Note 4
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
Product Series and
Basic Part Number
M85049/121 S 08 W
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Page 62-28
Finish
Table II
Page 62-28
B
.590
(14.99)
Max
Knurl Style
Optional
A Thread
E
F
G
Coupling Nut
D
.060/.250
(1.52/6.35)
Screw
Extension
Captive
Self-locking Nut
-typ-
Screw
C
See Note 4
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-129
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Dash Number, Shell Size, Thread and Dimensions (Continued Below)
Dash
No. Screw
Size
Connector Shell
Size
Series I Series II
A Thread
Class 2B B Dia
Max
C Dim
± .031 (0.79)
See Note 4
D
Min E Max
Length F
Dim G
Max
08 4-40 9 8 7/16-28 UNEF .858 (21.8) .219 (5.6) .22 (5.6) 1.01 (25.7) .77 (19.6)
.51 (13.0) .88 (22.4)
10 4-40 11 10 9/16-24 UNEF .984 (25.0) .264 (6.7) .27 (6.9) 1.13 (28.7) .89 (22.6)
.64 (16.3) .94 (23.9)
12 4-40 13 12 11/16-24 UNEF 1.157 (29.4) .344 (8.7) .35 (8.9) 1.25 (31.8) 1.01 (25.7)
.76 (19.3) 1.12 (28.4)
14 4-40 15 14 13/16-20 UNEF 1.297 (32.5) .460 (11.7) .47 (11.9) 1.25 (31.8) 1.01 (25.7)
.76 (19.3) 1.19 (30.2)
16 4-40 17 16 15/16-20 UNEF 1.406 (35.7) .545 (13.8) .55 (14.0) 1.37 (34.8) 1.13 (28.7)
.88 (22.4) 1.44 (36.6)
18 6-32 19 18 1 1/16-18 UNEF 1.516 (38.5) .615 (15.6) .62 (15.7) 1.62 (41.1) 1.38 (35.1)
1.13 (28.7) 1.56 (39.6)
20 6-32 21 20 1 3/16-18 UNEF 1.642 (41.7) .698 (17.7) .70 (17.8) 1.75 (44.5) 1.51 (38.4)
1.26 (32.0) 1.69 (42.9)
22 6-32 23 22 1 5/16-18 UNEF 1.768 (44.9) .780 (19.8) .78 (19.8) 1.87 (47.5) 1.63 (41.4)
1.38 (35.1) 1.75 (44.5)
24 8-32 25 24 1 7/16-18 UNEF 1.869 (47.5) .850 (21.6) .85 (21.6) 2.00 (50.8) 1.76 (44.7)
1.51 (38.4) 1.88 (47.8)
AS85049/121
Straight Strain Relief
Self-Locking or Non-Self-Locking
TABLE II: Material and Finish
Symbol Material Finish
A
Aluminum Alloy
Black Anodize
NElectroless Nickel
WCadmium, Olive Drab
XNickel Fluorocarbon Polymer
YPure Dense Electrodeposited
Aluminum
ZZinc Nickel
S300 Series SST Passivated
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-130
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/123
90° Strain Relief
Self-Locking or Non-Self Locking
Knurl Style
Optional
Ø.125 (3.2) Drain Holes
3 Min, Equally Spaced
G
B
.060/.380
(1.52/9.65)
Screw
Extension
H
F
Coupling Nut
A Thread
C
Captive
Self-locking Nut
-typ- Screw
E
.590
(14.99)
Max
D
See Note 4
Product Series and
Basic Part Number
M85049/123 S 08 W
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Page 62-30
Finish
Table II
Page 62-30
CONNECTOR DESIGNATOR:
FMIL-DTL-38999 Series I and II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-131
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Dash Number, Shell Size, Thread and Dimensions (Continued Below)
Dash
No. Screw
Size
Connector
Shell Size
Series I Series II
A Thread
Class 2B B Dia
Max
C Dim
± .031 (0.79)
See Note 4
D
Max E Max
Length F
Max G
Max H
Max
08 4-40 9 8 7/16-28 UNEF .858 (21.8) .219 (5.6) .86 (21.8) 1.10 (27.9) .81 (20.6) 1.24 (31.5) .88 (22.4)
10 4-40 11 10 9/16-24 UNEF .984 (25.0) .264 (6.7) .94 (23.9) 1.18 (30.0) .87 (22.1) 1.36 (34.5) .94 (23.9)
12 4-40 13 12 11/16-24 UNEF 1.157 (29.4) .344 (8.7) 1.14 (29.0) 1.38 (35.1) .93 (23.6) 1.51 (38.4) 1.12 (28.4)
14 4-40 15 14 13/16-20 UNEF 1.297 (32.5) .460 (11.7) 1.20 (30.5) 1.44 (36.6) .99 (25.1) 1.63 (41.4) 1.19 (30.2)
16 4-40 17 16 15/16-20 UNEF 1.406 (35.7) .545 (13.8) 1.34 (34.0) 1.58 (40.1) 1.09 (27.7) 1.76 (44.7) 1.44 (36.6)
18 6-32 19 18 1 1/16-18 UNEF 1.516 (38.5) .615 (15.6) 1.46 (37.1) 1.70 (43.2) 1.23 (31.2) 1.99 (50.5) 1.56 (39.6)
20 6-32 21 20 1 3/16-18 UNEF 1.642 (41.7) .698 (17.7) 1.58 (40.1) 1.82 (46.2) 1.30 (33.0) 2.12 (53.8) 1.69 (42.9)
22 6-32 23 22 1 5/16-18 UNEF 1.768 (44.9) .780 (19.8) 1.71 (43.4) 1.95 (49.5) 1.36 (34.5) 2.24 (56.9) 1.75 (44.5)
24 8-32 25 24 1 7/16-18 UNEF 1.869 (47.5) .850 (21.6) 1.83 (46.5) 2.07 (52.6) 1.42 (36.1) 2.35 (59.7) 1.88 (47.8)
Screw
Captive
Self-locking Nut
-typ- C
See Note 4
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
AS85049/123
90° Strain Relief
Self-Locking or Non-Self Locking
TABLE II: Material and Finish
Symbol Material Finish
A
Aluminum Alloy
Black Anodize
NElectroless Nickel
WCadmium, Olive Drab
XNickel Fluorocarbon Polymer
YPure Dense Electrodeposited
Aluminum
ZZinc Nickel
S300 Series SST Passivated
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-132
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/124
Straight Strain Relief
Self-Locking or Non-Self-Locking
Product Series and
Basic Part Number
M85049/124 S 09 W
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Page 62-32
Finish
Table II
Page 62-32
Coupling Nut
G
F
E
A Thread
Knurl Style
Optional .660
(16.76)
Max
CScrew
Captive
Self-locking Nut
-typ-
.25 (6.35)
Max Screw
Extension
D
B
See Note 4
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN3645
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-133
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Dash Number, Shell Size, Thread and Dimensions (Continued Below)
Dash
No. Screw
Size Shell Size
Code (Ref) A Thread
ISO Metric B Dia
Max
C Dim
± .031 (0.79)
See Note 4
D
Min E Max
Length F
Max G
Max
09 4-40 A M12 x 1 - 6H .858 (21.8) .219 (5.6) .22 (5.6) 1.05 (26.7) .77 (19.6) .88 (22.4)
11 4-40 B M15 x 1 - 6H .984 (25.0) .264 (6.7) .27 (6.9) 1.17 (22.6) .89 (22.6) .94 (23.9)
13 4-40 C M18 x 1 - 6H 1.157 (29.4) .344 (8.7) .35 (8.9) 1.29 (32.8) 1.01 (25.7) 1.12 (28.4)
15 4-40 D M22 x 1 - 6H 1.297 (32.5) .460 (11.7) .47 (11.9) 1.29 (32.8) 1.01 (25.7) 1.19 (30.2)
17 4-40 E M25 x 1 - 6H 1.406 (35.7) .545 (13.8) .55 (14.0) 1.41 (35.8) 1.13 (28.7) 1.44 (36.6)
19 6-32 F M28 x 1 - 6H 1.516 (38.5) .615 (15.6) .62 (15.7) 1.66 (42.2) 1.38 (35.1) 1.56 (39.6)
21 6-32 G M31 x 1 - 6H 1.642 (41.7) .698 (17.7) .70 (17.8) 1.79 (45.5) 1.51 (38.4) 1.69 (42.9)
23 6-32 H M34 x 1 - 6H 1.768 (44.9) .780 (19.8) .78 (19.8) 1.91 (48.5) 1.63 (41.4) 1.75 (44.5)
25 8-32 J M37 x 1 - 6H 1.869 (47.5) .850 (21.6) .85 (21.6) 2.04 (51.8) 1.76 (44.7) 1.88 (47.8)
Screw
Captive
Self-locking Nut
-typ- C
See Note 4
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
AS85049/124
Straight Strain Relief
Self-Locking or Non-Self-Locking
TABLE II: Material and Finish
Symbol Material Finish
A
Aluminum Alloy
Black Anodize
NElectroless Nickel
WCadmium, Olive Drab
XNickel Fluorocarbon Polymer
YPure Dense Electrodeposited
Aluminum
ZZinc Nickel
S300 Series SST Passivated
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-134
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/126
90° Strain Relief
Self-Locking or Non-Self-Locking
Product Series and
Basic Part Number
M85049/126 S 09 W
S = Detented Self-Locking
N = Non-Detented Self-Locking
Use Dash (–) for Non-Self-Locking
(See Note 5)
Dash No.
Table I
Page 62-34
Finish
Table II
Page 62-34
Knurl Style
Optional
Ø.125 (3.2) Drain Holes
3 Min, Equally Spaced
G
B
.060/.380
(1.52/9.65)
Screw
Extension
H
F
Coupling Nut
A Thread
C
Captive
Self-locking Nut
-typ- Screw
E
.660
(16.8)
Max
D
See Note 4
CONNECTOR DESIGNATOR:
HMIL-DTL-38999 Series III & IV
EN3645
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-135
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Screw
Captive
Self-locking Nut
-typ- C
See Note 4
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Glenair Series 600 Backshell Assembly Tools are recommended for assembly and
installation.
3. Metric equivalents in parentheses (mm) are given for general information only and are
based on 1.000 inch = 25.4 mm.
4. Cable entry is measured with saddle bars closed and bottomed on clamp ears.
5. Detented self-locking has a positive audible detented coupling.
6. Material/Finish:
Clamp body, coupling nut, saddles - Al alloy or 300 Series SST/See Table II.
Clamp screws and lock nuts - CRES/Passivated, Silver plate optional.
Anti-rotation device - Corrosion resistant material
TABLE I: Dash Number, Shell Size, Thread and Dimensions
Dash
No. Screw
Size Shell Size
Code (Ref) A Thread
ISO Metric B Dia
Max
C Dim
± .031 (0.79)
See Note 4
D
Max E Max
Length F
Max G
Max H
Max
09 4-40 A M12 x 1 - 6H .858 (21.8) .219 (5.6) .86 (21.8) 1.14 (29.0) .81 (20.6) 1.24 (31.5) .88 (22.4)
11 4-40 B M15 x 1 - 6H .984 (25.0) .264 (6.7) .94 (23.9) 1.22 (31.0) .87 (22.1) 1.36 (34.5) .94 (23.9)
13 4-40 C M18 x 1 - 6H 1.157 (29.4) .344 (8.7) 1.14 (29.0) 1.42 (36.1) .93 (23.6) 1.51 (38.4) 1.12 (28.4)
15 4-40 D M22 x 1 - 6H 1.297 (32.5) .460 (11.7) 1.20 (30.5) 1.48 (37.6) .99 (25.1) 1.63 (41.4) 1.19 (30.2)
17 4-40 E M25 x 1 - 6H 1.406 (35.7) .545 (13.8) 1.34 (34.0) 1.62 (41.1) 1.09 (27.7) 1.76 (44.7) 1.44 (36.6)
19 6-32 F M28 x 1 - 6H 1.516 (38.5) .615 (15.6) 1.46 (37.1) 1.74 (44.2) 1.23 (31.2) 1.99 (50.5) 1.56 (39.6)
21 6-32 G M31 x 1 - 6H 1.642 (41.7) .698 (17.7) 1.58 (40.1) 1.86 (47.2) 1.30 (33.0) 2.12 (53.8) 1.69 (42.9)
23 6-32 H M34 x 1 - 6H 1.768 (44.9) .780 (19.8) 1.71 (43.4) 1.99 (50.5) 1.36 (34.5) 2.24 (56.9) 1.75 (44.5)
25 8-32 J M37 x 1 - 6H 1.869 (47.5) .850 (21.6) 1.83 (46.5) 2.11 (53.6) 1.42 (36.1) 2.35 (59.7) 1.88 (47.8)
AS85049/126
90° Strain Relief
Self-Locking or Non-Self-Locking
TABLE II: Material and Finish
Symbol Material Finish
A
Aluminum Alloy
Black Anodize
NElectroless Nickel
WCadmium, Olive Drab
XNickel Fluorocarbon Polymer
YPure Dense Electrodeposited
Aluminum
ZZinc Nickel
S300 Series SST Passivated
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-136
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
AS85049/127
Bushing Strip
.12 (3.0)
±.03 (0.8)
Typ .075 (1.9)
±.015 (0.4)
.24 (6.1)
±.03 (0.8)
10.00 (254.0)
±.12 (3.0) A
.040 (1.0)
±.010 (0.3)
Typ
.12 (3.0)
±.03 (0.8)
Basic
Part Number
M85049/127 -02
Order No.
Table I
TABLE I: Order Number, Dimensions, Sizes
Order
No.
A
.031 (0.8)
Dim
Used on Size
/118, /120,
/121, /123
Used on Size
/124, /126
01 .312 (7.9) 03-16 09-17
02 .440 (11.2) 18-24 and 61 19-25
03 .560 (14.2) 28-40 –
APPLICATION NOTES
1. Assembly identied by bag and tag in suitable
quantities.
2. Material/nish: Silicone/N.A.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-139
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
Standard Band M85049/128-3 and
Precoiled Standard Band M85049/128-4
The M85049/128-3 and -4 Standard Band
is precision constructed of 300 Series SST/
Passivate and designed for use with the Glenair
600-058 (QPL’d) hand banding tool, double-
wrapped bands will accommodate diameters up
to approximately 1.8 inches (45.7). Bands may
be ordered at (M85049/128-3) or precoiled
(M85049/128-4). Bands come bagged and
tagged in quantities from 1 to 100.
14.256 ± .030
(362.1 ± 0.8)
Tail Length Indicator Mark
.350 (8.9) Ref.
.020 (0.5) Ref.
.156 (4.0) Ref.
.074 (1.9) Ref.
.240 (6.1) Ref.
AS85049/128-3 and AS85049/128-4
Clamping Band
Standard Length, Flat or Precoiled
Basic Part Number
M85049/128 = Clamping Band
3 = Standard Length
4 = Precoiled
M85049/128 -3
Metric dimensions (mm) are indicated in parentheses. Consult factory for diameters above 2.5 inches (63.5).
Rev. 1/2/18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-138
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells
AS85049/130
Gasket
Material
C = Conductive Silicone with Aluminum or Monel Mesh, Capable of 80 dB at 100 MHz.
Temperature Range -57° to +260° C.
F = Fluorosilicone IAW SAE AMS-R-25988
M = Conductive Silver Filled Silicone IAW MIL-DTL-3528 Type B, Capable of 110 dB at
10GHz. Temperature Range -55° to +260° C.
N = Neoprene IAW AMS 3208.
S = Silicone IAW AA-59588
V = Viton IAW MIL-R-83248
Basic
Part Number
M85049/130 -18 S
Dash Number
Table I
TABLE I: Dimensions
Dash
No.
A
± .015 (0.38)
B
+.020 (0.05)
-.000
C
± .015 (0.38)
D
± .010 (0.25)
01 .594 (15.09) .568 (14.43) .812 (20.62) .125 (3.18)
02 .594 (15.09) .500 (12.70) .875 (22.23) .156 (3.96)
03 .625 (15.88) .603 (15.32) .896 (22.76) .125 (3.18)
04 .719 (18.26) .680 (12.27) .937 (23.80) .125 (3.18)
05 .719 (18.26) .625 (15.88) 1.000 (25.40) .156 (3.96)
06 .750 (19.05) .750 (19.05) 1.023 (25.98) .125 (3.18)
07 .812 (20.62) .875 (22.23) 1.060 (26.92) .141 (3.58)
08 .812 (20.62) .828 (21.03) 1.114 (28.30) .125 (3.18)
09 .813 (20.65) .750 (19.05) 1.094 (27.79) .141 (3.58)
10 .843 (21.41) .875 (22.23) 1.138 (28.91) .125 (3.58)
11 .906 (23.01) 1.005 (25.53) 1.153 (29.29) .125 (3.58)
12 .906 (23.01) .938 (23.83) 1.125 (28.58) .125 (3.58)
13 .906 (23.01) .875 (22.23) 1.188 (30.18) .156 (3.96)
14 .969 (24.61) 1.135 (28.83) 1.258 (31.95) .156 (3.96)
15 .969 (24.61) 1.063 (27.00) 1.250 (31.75) .125 (3.58)
C
A
AC
B Dia
D Dia Hole 4 Places Chamfer or Radius Mfr. Option
.037/.027
(0.94x0.69)
Continued on Page B-141
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-139
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
AS85049/130
Gasket
TABLE I: Dimensions
(Continued From Page B-140)
Dash
No.
A
± .015 (0.38)
B
+.020 (0.05)
-.000
C
± .015 (0.38)
D
± .010 (0.25)
16 .969 (24.61) 1.000 (25.4) 1.281 (32.54) .156 (3.69)
17 1.015 (25.78) 1.125 (28.58) 1.383 (35.13) .125 (3.18)
18 1.062 (26.97) 1.260 (32.00) 1.351 (34.32) .156 (3.96)
19 1.062 (26.97) 1.189 (30.20) 1.343 (34.11) .125 (3.18)
20 1.062 (26.97) 1.135 (28.83) 1.375 (34.92) .156 (3.96)
21 1.140 (28.96) 1.312 (33.32) 1.508 (38.30) .125 (3.18)
22 1.156 (29.36) 1.375 (34.92) 1.500 (38.10) .141 (3.58)
23 1.156 (29.36) 1.312 (33.32) 1.467 (37.26) .125 (3.18)
24 1.156 (29.36) 1.250 (31.75) 1.500 (38.10) .177 (4.50)
25 1.187 (30.15) 1.266 (32.16) 1.458 (37.03) .125 (3.58)
26 1.250 (31.75) 1.500 (38.10) 1.625 (41.28) .141 (3.58)
27 1.250 (31.75) 1.437 (36.50) 1.562 (39.67) .125 (3.58)
28 1.250 (31.75) 1.375 (34.92) 1.625 (41.28) .177 (4.50)
29 1.281 (32.54) 1.500 (38.10) 1.718 (43.64) .125 (3.18)
30 1.375 (34.92) 1.625 (41.28) 1.750 (44.45) .177 (3.18)
31 1.375 (34.92) 1.563 (39.70) 1.703 (43.26) .156 (3.96)
32 1.375 (34.92) 1.500 (38.10) 1.750 (44.45) .203 (5.16)
33 1.392 (35.36) 1.625 (41.28) 1.818 (46.18) .141 (3.58)
34 1.436 (36.47) 1.570 (39.88) 1.799 (45.69) .125 (3.18)
35 1.500 (38.10) 1.750 (44.45) 1.875 (47.63) .177 (3.18)
36 1.562 (39.67) 1.750 (44.45) 2.000 (50.80) .203 (5.16)
37 1.568 (39.83) 1.875 (47.63) 2.138 (54.31) .141 (3.58)
38 1.719 (43.66) 2.000 (50.80) 2.375 (60.33) .177 (3.18)
39 1.734 (44.04) 2.062 (52.37) 2.328 (59.13) .177 (3.18)
40 1.750 (44.45) 2.000 (50.80) 2.250 (57.15) .219 (5.56)
41 1.906 (48.41) 2.250 (57.15) 2.625 (66.68) .219 (5.56)
42 1.938 (49.23) 2.250 (57.15) 2.500 (63.50) .219 (5.56)
43 2.188 (55.58) 2.500 (63.50) 2.750 (69.85) .219 (5.56)
44 2.375 (60.33) 2.781 (70.64) 3.000 (76.20) .219 (5.56)
45 2.406 (61.11) 2.750 (69.85) 3.125 (79.38) .281 (7.14)
46 2.625 (66.68) 3.031 (76.99) 3.250 (82.55) .219 (5.56)
47 2.656 (67.46) 3.000 (76.20) 3.375 (85.73) .281 (7.14)
48 2.906 (73.81) 3.250 (82.55) 3.625 (92.08) .281 (7.14)
49 3.156 (80.16) 3.500 (88.90) 3.875 (98.43) .281 (7.14)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-140
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 09.28.15
MS3420 and AS85049/139
Telescoping Bushing
Material
A = Neoprene
D = Silicone
L = Fluorosilicone
Material
A = Neoprene
D = Silicone
L = Fluorosilicone
MS3420 -3 L
Basic
Part Number
Dash
Number
M85049/139 -3 L
E
F
2.062/1.938 (52.4/49.2)
MS3420 -3
Basic
Part Number
Dash
Number
Material: Neoprene
M85049/139 -3
D
CB
A.020/.010 (0.5/0.3)
R .015 (0.4) Min
.046/.078
(1.2/2.0)
R .015 (0.4) Min
R .015
(0.4)
Min
45°
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-141
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
TABLE I: Reference for Connector Shell Size
Dash
No. Ø A
Dia Ø B
Dia Ø C
Dia D Dim
Dia E
Dia F
Dia
3.150/.110 (3.8/2.8) .230/.190 (5.8/4.8) .395/.363 (10.0/9.2) 2.906/2.844 (73.8/72.2) .150/.110 (3.8/2.8) .230/.190 (5.8/4.8)
4.240/.200 (6.1/5.1) .322/.282 (8.2/7.2) .521/.489 (13.2/12.4) 2.781/2.719 (70.6/69.1) .240/.200 (6.1/5.1) .322/.282 (8.2/7.2)
6.332/.292 (8.4/7.4) .447/.407 (11.4/10.3) .635/.603 (16.1/15.3) 2.656/2.594 (67.5/65.9) .332/.292 (8.4/7.4) .447/.407 (11.4/10.3)
8.464/.410 (11.8/10.4) .579/.525 (14.7/13.3) .760/.728 (19.3/18.5) 2.531/2.469 (64.3/62.7) .464/.410 (11.8/10.4) .579/.525 (14.7/13.3)
10 .589/.535 (15.0/13.6) .652/.535 (16.6/13.6) .905/.873 (23.0/59.5) 2.406/2.344 (61.1/10.4) .464/.410 (11.8/10.4) .642/.588 (16.3/14.9)
12 .652/.598 (16.6/15.2) .767/.713 (19.5/18.1) 1.100/1.068 (27.9/27.1) 2.281/2.219 (57.9/56.4) .568/.514 (14.4/13.1) .767/.713 (19.5/18.1)
16 .777/.723 (19.7/18.4) .954/.900 (24.2/22.9) 1.330/1.298 (33.8/33.0) 2.156/2.094 (54.8/53.2) .777/.723 (19.7/18.4) .954/.900 (24.2/22.9)
18 –– –– –– –– .976/.898 (24.8/22.8) 1.142/1.088 (29.0/27.6)
20 .976/.898 (24.8/22.8) 1.279/1.201 (32.5/30.5) 1.614/1.582 (41.0/40.2) 2.031/1.969 (51.6/50.0) .976/.898 (24.8/22.8) 1.279/1.201 (32.5/30.5)
24 1.289/1.211 (32.7/30.8) 1.404/1.326 (35.7/33.7) 1.863/1.831 (47.3/46.5) 1.906/1.844 (48.4/46.8) 1.164/1.086 (29.6/27.6) 1.404/1.326 (35.7/33.7)
28 1.414/1.336 (35.9/33.9) 1.653/1.575 (42.0/40.0) 2.101/2.069 (53.4/52.6) 1.781/1.719 (45.2/43.7) 1.289/1.719 (45.2/43.7) 1.653/1.575 (42.0/40.0)
32 1.675/1.573 (42.5/40.0) 1.915/1.813 (48.6/46.1) 2.351/2.319 (59.7/58.9) 1.656/1.594 (42.1/40.0) 1.676/1.574 (42.6/40.0) 1.916/1.814 (48.7/46.1)
40 1.925/1.823 (48.9/46.3) 2.415/2.313 (61.3/58.8) 2.851/2.819 (72.4/71.6) 1.531/1.469 (38.9/37.3) 1.926/1.824 (48.9/46.3) 2.416/2.314 (61.4/58.8)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
MS3420 and AS85049/139
Telescoping Bushing
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-142
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/140
Straight Lipped Heat Shrink Boot
Basic
Part Number
M85049/140 -05 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection
Vent Ports
P = Vent Ports
Omit for None
As Supplied
H Dia J Dia
As Recovered with Drain Holes
H Dia J Dia
P
JW
HW
R
H
S
Optional Ø.12 (3.05) Drain Holes
(4 Places, 90° Apart)
See
Note 2
T
.12 Ref
(3.05)
H
As Recovered with Injection-Vent Port
PP
RR
Optional
Ø.12 (3.05)
Vent Port
Optional
Ø.18 (4.57)
Injection Port
See
Note 2
Additional Boot Lips
(Mfr Option)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-143
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia Min
(As Supplied)
H Dia Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Min
(As Supplied)
Material G
J Dia Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
01 0.92 (23.4) 0.41 (10.4) 0.92 (23.4) 0.47 (11.9) 0.24 (6.1) 1.50 (38.1) 0.83 (21.1)
02 1.12 (28.4) 0.56 (14.2) 1.12 (28.4) 0.58 (14.7) 0.26 (6.6) 2.16 (54.9) 1.09 (27.7)
03 1.22 (31.0) 0.70 (17.6) 1.22 (31.0) 0.63 (16.0) 0.28 (7.1) 2.63 (66.8) 1.39 (35.3)
04 1.42 (36.1) 0.88 (22.4) 1.42 (36.1) 0.73 (18.5) 0.38 (9.7) 3.15 (80.0) 1.63 (41.4)
05 1.68 (42.7) 1.11 (28.2) 1.68 (42.7) 0.87 (22.1) 0.39 (9.9) 4.08 (103.6) 2.22 (56.4)
06 2.04 (51.8) 1.38 (35.1) 2.04 (51.8) 1.39 (35.3) 0.63 (16.0) 5.13 (130.3) 2.54 (64.5)
07 2.60 (66.0) 1.75 (44.5) 2.60 (66.0) 1.80 (45.7) 0.80 (20.3) 6.50 (165.1) 3.31 (84.1)
08 3.22 (81.8) 2.27 (57.7) 3.22 (81.8) 2.25 (57.2) 1.00 (25.4) 7.00 (177.8) 3.75 (95.3)
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
Ref
HW
(As Recovered)
±20%
JW Max
(As Recovered)
PP
(As Recovered)
±10%
S
(As Recovered)
±10%
RR
(As Recovered)
±10%
01 0.04 (1.0) 0.07 (1.8) 0.09 (2.2) 0.60 (15.2) 0.48 (12.2) N/A
02 0.04 (1.0) 0.07 (1.8) 0.09 (2.2) 0.60 (15.2) 0.49 (12.4) .85 (21.6)
03 0.04 (1.0) 0.08 (2.0) 0.10 (2.5) 0.60 (15.2) 0.75 (19.1) .96 (24.4)
04 0.04 (1.0) 0.08 (2.0) 0.10 (2.5) 0.60 (15.2) 0.75 (19.1) 1.17 (29.7)
05 0.07 (1.8) 0.09 (2.3) 0.11 (2.7) 0.60 (15.2) 0.75 (19.1) 1.44 (36.6)
06 0.07 (1.8) 0.13 (3.3) 0.16 (4.0) 0.60 (15.2) 0.57 (14.5) 2.12 (53.8)
07 0.08 (2.0) 0.16 (4.1) 0.19 (4.9) 0.60 (15.2) 0.68 (17.3) 2.59 (65.8)
08 0.08 (2.0) 0.16 (4.1) 0.19 (4.9) 0.60 (15.2) 0.68 (17.3) 2.64 (67.1)
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
AS85049/140
Straight Lipped Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-144
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/140
Straight Lipped Long Tail Low Prole
Heat Shrink Boot
Basic
Part Number
M85049/140 -09 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection
Vent Ports
P = Vent Ports
Omit for None
J Dia
As Supplied
H
TOptional
Ø.12 (3.05)
Vent Port
Optional
Ø.18 (4.57)
Injection Port
U
See
Note 2
H
As Recovered with Injection-Vent Port
.12 Ref
(3.05)
See
Note 2
P
Optional
Ø.12 (3.05) Drain Holes
(4 Places, 90° Apart)
R
S
H
As Recovered with Drain Holes
HW JW
J Dia
H Dia
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-145
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Min
(As Recovered)
Material G
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
09 0.88 (22.4) 0.47 (11.9) 0.88 (22.4) 0.55 (14.0) 0.25 (6.4) 4.17 (105.9) 0.46 (11.7)
10 0.98 (24.9) 0.59 (15.0) 0.98 (24.9) 0.63 (16.0) 0.30 (7.6) 4.77 (121.2) 0.48 (12.2)
11 1.16 (29.5) 0.75 (19.1) 1.16 (29.5) 0.72 (18.3) 0.33 (8.4) 5.46 (138.7) 0.48 (12.2)
12 1.34 (34.0) 0.91 (23.1) 1.34 (34.0) 0.84 (21.3) 0.39 (9.9) 6.28 (159.5) 0.48 (12.2)
13 1.47 (37.3) 1.18 (30.0) 1.47 (37.3) 0.91 (23.1) 0.43 (10.9) 7.00 (177.8) 0.55 (14.0)
14 1.72 (43.7) 1.34 (34.0) 1.72 (43.7) 1.07 (27.2) 0.48 (12.2) 8.00 (203.2) 0.60 (15.2)
15 1.97 (50.0) 1.62 (41.1) 1.97 (50.0) 1.24 (31.5) 0.57 (14.5) 8.00 (203.2) 0.60 (15.2)
16 2.47 (62.7) 1.85 (47.0) 2.47 (62.7) 1.54 (39.1) 0.71 (18.0) 8.00 (203.2) 0.63 (16.0)
17 2.73 (69.3) 2.36 (59.9) 2.73 (69.3) 1.70 (43.2) 0.79 (20.1) 8.00 (203.2) 0.63 (16.0)
18 3.22 (81.8) 2.64 (67.1) 3.22 (81.8) 2.01 (51.1) 0.91 (23.1) 8.00 (203.2) 0.63 (16.0)
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
Ref
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
S
(As Recovered)
±10%
U
(As Recovered)
±10%
09 0.04 (1.0) 0.06 (1.5) 0.05 (1.1) 0.23 (5.8) 0.56 (14.2)
10 0.04 (1.0) 0.06 (1.5) 0.05 (1.1) 0.24 (6.1) 0.59 (15.0)
11 0.04 (1.0) 0.07 (1.8) 0.05 (1.1) 0.47 (11.9) 0.61 (15.5)
12 0.04 (1.0) 0.07 (1.8) 0.05 (1.1) 0.47 (11.9) 0.62 (15.7)
13 0.07 (1.7) 0.08 (2.0) 0.05 (1.1) 0.47 (11.9) 0.71 (18.0)
14 0.07 (1.7) 0.08 (2.0) 0.05 (1.1) 0.47 (11.9) 0.78 (19.8)
15 0.07 (1.7) 0.09 (2.3) 0.06 (1.5) 0.30 (7.6) 0.82 (20.8)
16 0.08 (2.0) 0.10 (2.5) 0.06 (1.5) 0.63 (16.0) 0.92 (23.4)
17 0.08 (2.0) 0.10 (2.5) 0.06 (1.5) 0.63 (16.0) 0.93 (23.6)
18 0.08 (2.0) 0.10 (2.5) 0.06 (1.5) 0.63 (16.0) 1.23 (31.2)
AS85049/140
Straight Lipped Long Tail Low Prole
Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-146
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/140
Straight Lipped Miniature Long Tail High Ratio
Low Prole Heat Shrink Boot
Basic
Part Number
M85049/140 -20 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection
Vent Ports
P = Vent Ports
Omit for None
As Supplied
J Dia
H Dia
Optional
Ø.120 (3.05)
Vent Port
Optional
Ø.180 (4.57)
Injection Port
U
See
Note 2
H
As Recovered with Injection-Vent Port
.120 Ref
(3.05)
P
R
H
HW
S
JW
As Recovered with Drain Holes
H Dia J Dia
See
Note 2
TOptional
Ø.120 (3.05) Drain Holes
(4 Places, 90° Apart)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-147
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Min
(As Supplied)
Material G
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
19 0.76 (19.3) 0.51 (13.0) 0.25 (6.4) 0.18 (4.6) 0.08 (2.0) 2.37 (60.2) 0.46 (11.7)
20 1.03 (26.2) 0.75 (19.1) 0.30 (7.6) 0.22 (5.6) 0.10 (2.5) 2.92 (74.2) 0.48 (12.2)
21 1.35 (34.3) 1.02 (25.9) 0.38 (9.7) 0.26 (6.6) 0.12 (3.0) 3.32 (84.3) 0.48 (12.2)
22 1.72 (43.7) 1.34 (34.0) 0.45 (11.4) 0.31 (7.9) 0.14 (3.6) 3.92 (99.6) 0.48 (12.2)
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
±10%
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
S
(As Recovered)
±10%
U
(As Recovered)
±10%
19 0.04 (1.0) 0.06 (1.5) 0.05 (1.14) 0.47 (11.9) 0.62 (15.75)
20 0.04 (1.0) 0.07 (1.8) 0.05 (1.14) 0.47 (11.9) 0.80 (20.32)
21 0.04 (1.0) 0.07 (1.8) 0.05 (1.14) 0.47 (11.9) 0.90 (22.86)
22 0.07 (1.7) 0.07 (1.8) 0.05 (1.14) 0.47 (11.9) 1.03 (26.16)
AS85049/140
Straight Lipped Miniature Long Tail High Ratio
Low Prole Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-148
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/140
Straight Lipped Sealing Heat Shrink Boot
Basic
Part Number
M85049/140 -25 H C
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
H Dia J Dia
As Supplied
RP
.120 (3.05)
Ref
HW JW
J Dia
H Dia
H
See Note 2
As Recovered
T
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-149
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia
Min
(As Supplied)
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
T
(As Recovered)
±10%
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
23 0.84 (21.3) 0.55 (14.0) 0.66 (16.8) 0.21 (5.3) 5.30 (134.6) 1.10 (27.9) 0.06 (1.5) 0.16 (4.1) 0.04 (1.0)
24 1.00 (25.4) 0.65 (16.5) 1.00 (25.4) 0.33 (8.4) 6.00 (152.4) 1.20 (30.5) 0.06 (1.5) 0.16 (4.1) 0.06 (1.5)
25 1.30 (33.0) 0.80 (20.3) 1.30 (33.0) 0.43 (10.9) 6.00 (152.4) 1.20 (30.5) 0.06 (1.5) 0.16 (4.1) 0.06 (1.5)
26 1.70 (43.2) 0.90 (22.9) 1.70 (43.2) 0.56 (14.2) 6.90 (175.3) 1.50 (38.1) 0.06 (1.5) 0.16 (4.1) 0.08 (2.0)
27 2.10 (53.3) 1.10 (27.9) 2.10 (53.3) 0.70 (17.8) 6.90 (175.3) 1.50 (38.1) 0.06 (1.5) 0.16 (4.1) 0.08 (2.0)
28 2.85 (72.4) 1.45 (36.4) 2.85 (72.4) 0.95 (24.1) 7.24 (183.9) 1.60 (40.6) 0.06 (1.5) 0.20 (5.1) 0.10 (2.54)
AS85049/140
Straight Lipped Sealing Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-150
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/141
90° Lipped Heat Shrink Boot
Basic
Part Number
M85049/141 -03 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection Vent-Ports
Omit for None
H Dia J Dia
As Supplied
Optional
Ø.180 (4.57)
Injection Port
Optional
Ø.120 (3.05)
Vent Port
K
H
L
As Recovered with Injection-Vent Port
See
Note 2
Optional Ø.120 (3.05)
Drain Holes
(4 Places, 90° Apart
and one on Top)
S
R
P
U
HW
H Dia
JW
J Dia
As Recovered with Drain Holes
.120 Ref
(3.05)
T
H
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-151
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
AS85049/141
90° Lipped Heat Shrink Boot
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Min
(As Supplied)
Material G
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
±10%
01 0.920 (23.4) 0.410 (10.4) 0.920 (23.4) 0.470 (11.9) 0.240 (6.1) 0.840 (21.3) 0.650 (16.5)
02 1.120 (28.4) 0.610 (15.5) 1.120 (28.4) 0.580 (14.7) 0.260 (6.6) 1.330 (33.8) 0.760 (19.3)
03 1.220 (31.0) 0.710 (18.0) 1.220 (31.0) 0.630 (16.0) 0.280 (7.1) 1.440 (36.6) 0.830 (21.1)
04 1.420 (36.1) 0.890 (22.6) 1.420 (36.1) 0.730 (18.5) 0.330 (8.4) 1.720 (43.7) 0.900 (22.9)
05 1.680 (42.7) 1.120 (28.4) 1.680 (42.7) 0.870 (22.1) 0.390 (9.9) 2.110 (53.6) 1.140 (29.0)
06 2.040 (51.8) 1.380 (35.1) 2.040 (51.8) 1.390 (35.3) 0.630 (16.0) 3.070 (78.0) 1.320 (33.5)
07 2.600 (66.0) 1.770 (45.0) 2.600 (66.0) 1.800 (45.7) 0.800 (20.3) 3.840 (97.5) 1.640 (41.7)
08 3.220 (81.8) 2.400 (61.0) 3.220 (81.8) 2.250 (57.2) 1.000 (25.4) 4.640 (117.9) 2.030 (51.6)
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
Ref
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
S
(As Recovered)
±10%
U
(As Recovered)
±10%
K
(As Recovered)
±10%
L
(As Recovered)
±10%
01 0.040 (1.0) 0.050 (1.3) 0.050 (1.3) 0.450 (11.4) 0.470 (11.9) 0.600 (15.2) 0.580 (14.7)
02 0.040 (1.0) 0.060 (1.5) 0.050 (1.3) 0.470 (11.9) 1.020 (25.9) 0.750 (19.1) 0.980 (24.9)
03 0.040 (1.0) 0.070 (1.8) 0.070 (1.8) 0.470 (11.9) 1.090 (27.7) 0.750 (19.1) 0.980 (24.9)
04 0.040 (1.0) 0.070 (1.8) 0.070 (1.8) 0.470 (11.9) 1.160 (29.5) 0.750 (19.1) 1.180 (30.0)
05 0.070 (1.8) 0.080 (2.0) 0.080 (2.0) 0.470 (11.9) 1.470 (37.3) 0.760 (19.3) 1.300 (33.0)
06 0.070 (1.8) 0.130 (3.3) 0.130 (3.3) 0.530 (13.5) 2.500 (63.5) 1.000 (25.4) 2.120 (53.8)
07 0.080 (2.0) 0.150 (3.8) 0.150 (3.8) 0.640 (16.3) 2.750 (69.9) 1.000 (25.4) 2.800 (71.1)
08 0.080 (2.0) 0.160 (4.1) 0.160 (4.1) 0.640 (16.3) 3.120 (79.2) 1.000 (25.4) 3.150 (80.0)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-152
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/141
90° Lipped Low Prole Heat Shrink Boot
Basic
Part Number
M85049/141 -10 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection Vent-Ports
Omit for None
As Supplied
J Dia
H Dia
P
H Dia
HW
J Dia
JW
As Recovered
with Drain Holes
R
H
S
T
.120 Ref
(3.05)
Optional Ø.120 (3.05)
Drain Holes
(4 Places, 90° Apart and on Top)
See
Note 2
As Recovered
with Injection-Vent Port
H
PP
RR
Optional
Ø.120 (3.05)
Vent Port
Optional
Ø.180 (4.57)
Injection Port
See
Note 2
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-153
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Max
(As Supplied)
Material G
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
09 0.880 (22.4) 0.450 (11.4) 0.880 (22.4) 0.550 (14.0) 0.250 (6.4) 4.140 (105.2) 0.730 (18.5)
10 1.010 (25.7) 0.590 (15.0) 1.010 (25.7) 0.630 (16.0) 0.300 (7.6) 4.880 (124.0) 0.780 (19.8)
11 1.160 (29.5) 0.740 (18.8) 1.160 (29.5) 0.720 (18.3) 0.330 (8.4) 5.760 (146.3) 0.820 (20.8)
12 1.340 (34.0) 0.900 (22.9) 1.340 (34.0) 0.840 (21.3) 0.390 (9.9) 6.780 (172.2) 0.860 (21.8)
13 1.470 (37.3) 1.160 (29.5) 1.470 (37.3) 0.910 (23.1) 0.430 (10.9) 7.290 (185.2) 0.960 (24.4)
14 1.720 (43.7) 1.340 (34.0) 1.720 (43.7) 1.070 (27.2) 0.480 (12.2) 8.410 (213.6) 1.080 (27.4)
15 1.970 (50.0) 1.620 (41.1) 1.970 (50.0) 1.240 (31.5) 0.570 (14.5) 8.840 (224.5) 1.160 (29.5)
16 2.470 (62.7) 1.850 (47.0) 2.470 (62.7) 1.540 (39.1) 0.710 (18.0) 8.950 (227.3) 1.310 (33.3)
17 2.730 (69.3) 2.350 (59.7) 2.730 (69.3) 1.700 (43.2) 0.790 (20.1) 9.190 (233.4) 1.380 (35.1)
18 3.220 (81.8) 2.640 (67.1) 3.220 (81.8) 2.010 (51.1) 0.910 (23.1) 9.330 (237.0) 1.750 (44.5)
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
Ref
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
S
(As Recovered)
±10%
PP
(As Recovered)
±10%
RR
(As Recovered)
±10%
09 0.040 (1.0) 0.060 (1.5) 0.060 (1.5) 0.470 (11.9) 0.270 (6.9) 0.490 (12.4)
10 0.040 (1.0) 0.060 (1.5) 0.060 (1.5) 0.470 (11.9) 0.330 (8.4) 0.590 (15.0)
11 0.040 (1.0) 0.070 (1.8) 0.060 (1.5) 0.470 (11.9) 0.410 (10.4) 0.610 (15.5)
12 0.040 (1.0) 0.070 (1.8) 0.060 (1.5) 0.470 (11.9) 0.480 (12.2) 0.620 (15.7)
13 0.070 (1.8) 0.080 (2.0) 0.060 (1.5) 0.470 (11.9) 0.610 (15.5) 0.700 (17.8)
14 0.070 (1.8) 0.080 (2.0) 0.060 (1.5) 0.470 (11.9) 0.720 (18.3) 0.780 (19.8)
15 0.070 (1.8) 0.090 (2.3) 0.060 (1.5) 0.470 (11.9) 0.830 (21.1) 0.820 (20.8)
16 0.080 (2.0) 0.100 (2.5) 0.060 (1.5) 0.630 (16.0) 0.950 (24.1) 0.920 (23.4)
17 0.080 (2.0) 0.100 (2.5) 0.060 (1.5) 0.630 (16.0) 1.180 (30.0) 0.930 (23.6)
18 0.080 (2.0) 0.100 (2.5) 0.060 (1.5) 0.630 (16.0) 1.310 (33.3) 1.230 (31.2)
AS85049/141
90° Lipped Low Prole Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-154
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/141
90° Lipped Miniature Low Prole Heat Shrink Boot
Basic
Part Number
M85049/141 -19 H C D P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Drain Holes
Omit for None
Injection Vent-Ports
Omit for None
As Supplied
H Dia
J Dia
H Dia
J Dia
P
R
Recovered
with Drain Holes
H
JW
Optional Ø.120 (3.05)
Drain Holes (4 Plcs) 90° apart
and one on Top. See Note 3
.120 Ref
(3.05)
S
HW
T
See
Note 2
See Note 2
H
Recovered
with Injection-Vent Port
U
Optional
Ø.180 (4.57)
Injection Port
Optional
Ø.120 (3.05)
Vent Port
See Note 3
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-155
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, not number on boot. See part number
development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“J” end. See part number development for full
description.
3. Dimensions applicable for both injection and
vent ports.
4. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J Dia Min
(As Supplied)
Material A, B, H
J Dia Max
(As Supplied)
Material G
J Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
19 0.760 (19.3) 0.510 (13.0) 0.250 (6.4) 0.180 (4.6) 0.080 (2.0) 1.750 (44.5) 0.640 (16.3)
20 1.030 (26.2) 0.750 (19.1) 0.300 (7.6) 0.220 (5.6) 0.100 (2.5) 2.650 (67.3) 0.710 (18.0)
21 1.350 (34.3) 1.020 (25.9) 0.380 (9.7) 0.260 (6.6) 0.120 (3.0) 3.200 (81.3) 0.740 (18.8)
22 1.720 (43.7) 1.340 (34.0) 0.450 (11.4) 0.310 (7.9) 0.140 (3.6) 4.550 (115.6) 0.840 (21.3)
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
T
(As Recovered)
Ref
HW
(As Recovered)
±20%
JW
Max
(As Recovered)
S
(As Recovered)
±10%
U
(As Recovered)
±10%
19 0.040 (1.0) 0.060 (1.5) 0.050 (1.1) 0.470 (11.90) 0.220 (5.6)
20 0.040 (1.0) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.330 (8.4)
21 0.040 (1.0) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.450 (11.4)
22 0.070 (1.8) 0.070 (1.8) 0.050 (1.1) 0.470 (11.90) 0.610 (15.5)
AS85049/141
90° Lipped Miniature Low Prole Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-156
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/142
Tee Transition Wide Body Heat Shrink Boot
Basic
Part Number
M85049/142 -02 H C P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Injection
Vent-Ports
Omit for None
K Dia
(C2)
J Dia
(C1) H Dia
As Supplied
30° ±10°
S
K Dia
J Dia
R
H Dia
P
W
3 Plcs
Recovered
T
Optional
Ø.12 (3.05)
Vent Port
(If Required)
H
Optional
Ø.180 (4.57)
Injection Port
(If Required)
See
Note 2
90° ±5°
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-157
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, matching dash number on boot. See
part number development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“K” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimension
Dash
No.
H, J, K Dia
Min
(As Supplied)
H, J, K Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
±10%
S
(As Recovered)
±10%
T
(As Recovered)
±10%
W
(As Recovered)
±20%
01 0.260 (6.6) 0.140 (3.6) 1.170 (29.7) 0.580 (14.7) 0.590 (15.0) N/A 0.040 (1.0)
02 0.520 (13.2) 0.270 (6.9) 2.310 (58.7) 1.160 (29.5) 1.160 (29.5) 0.690 (17.5) 0.060 (1.5)
03 1.060 (26.9) 0.530 (13.5) 4.730 (120.1) 2.360 (59.9) 2.370 (60.2) 1.400 (35.6) 0.090 (2.3)
04 2.190 (55.6) 1.190 (30.2) 9.700 (246.4) 4.850 (123.2) 4.850 (123.2) 2.790 (70.9) 0.120 (3.0)
AS85049/142
Tee Transition Wide Body Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-158
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/142
Wye Transition Wide Body Heat Shrink Boot
Basic
Part Number
M85049/142 -05 H C P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Injection
Vent-Ports
Omit for None
J Dia
(C1)
K Dia
(C2)
As Supplied
H Dia
R
HW
KW
JW
K Dia
J Dia
H Dia
As Recovered
H
T
S
22°30' ±5°
Optional
Ø.180 (4.57)
Injection Port
Optional
Ø.120 (3.05)
Vent Port
P
See
Note 2
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-159
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, matching dash number on boot. See
part number development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“K” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J & K Dia
Min
(As Supplied)
J & K Dia
Max
(As Recovered)
P
(As Recovered)
Ref
R
(As Recovered)
Ref
S
(As Recovered)
±10%
T
(As Recovered)
±10%
HW
(As Recovered)
±20%
JW & KW
(As Recovered)
±20%
05 0.520 (13.2) 0.240 (6.1) 0.260 (6.6) 0.130 (3.3) 0.880 (22.4) 0.760 (19.3) 0.940 (23.9) 0.610 (15.5) 0.060 (1.5) 0.040 (1.0)
06 1.060 (26.9) 0.490 (12.4) 0.520 (13.2) 0.240 (6.1) 1.500 (38.1) 1.700 (43.2) 2.100 (53.3) 1.300 (33.0) 0.100 (2.5) 0.060 (1.5)
07 1.520 (38.6) 0.710 (18.0) 1.060 (26.9) 0.490 (12.4) 2.580 (65.5) 3.100 (78.7) 3.100 (78.7) 2.200 (55.9) 0.120 (3.0) 0.100 (2.5)
08 2.190 (55.6) 1.020 (25.9) 1.060 (26.9) 0.500 (12.7) 3.350 (85.1) 3.700 (94.0) 4.400 (111.8) 2.800 (71.1) 0.180 (4.6) 0.100 (2.5)
AS85049/142
Wye Transition Wide Body Heat Shrink Boot
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-160
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
AS85049/142
1:3 Transition Wide Body Heat Shrink Boot
Basic
Part Number
M85049/142 -10 H C P
Adhesive
C = Adhesive Lined
U = No Adhesive
Table III
Dash
Number
Table I
Material
Table II
See Note 2
Injection
Vent-Ports
Omit for None
K Dia
(C2)
As Supplied
H Dia
J Dia
(C1)
L Dia
(C3)
Optional
Ø.120 (3.05)
Vent Port
Optional
Ø.180 (4.57)
Injection Port
T
S
U
H
Recovered
R
P
HW
H Dia
L Dia
K Dia
W (3x)
J Dia
30°±5°
Typ
See
Note 2
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
B-161
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS85049
B
Mil-Spec Backshells Rev. 8.29.14
APPLICATION NOTES
1. See bag identication for matching boot
number, matching dash number on boot. See
part number development for full description.
2. Encircled material letter designator located
on O.D. approximately mid length along the
“H” end. See part number development for full
description.
3. Metric dimensions (mm) are in parentheses.
TABLE II: Shrink Boot Materials
Material
Code Compound Material Description Color
Code
A2071 Flexible Polyolen WHITE
B2040 General Purpose Polyolen RED
G2010 Zero Halogen Polyolen GREEN
H2025 High Performance Elastomer BLUE
TABLE III: Adhesive Description
Symbol Adhesive Description
CZero Halogen / Hot Melt
TABLE I: Dash Number and Dimensions (Continued Below)
Dash
No.
H Dia
Min
(As Supplied)
H Dia
Max
(As Recovered)
J, K, L Dia
Min
(As Supplied)
J, K, L Dia
Max
(As Recovered)
P
(As Recovered)
±10%
R
(As Recovered)
Ref
09 0.520 (13.2) 0.260 (6.6) 0.260 (6.6) 0.140 (3.6) 1.820 (46.2) 1.000 (25.4)
10 1.060 (26.9) 0.530 (13.5) 0.520 (13.2) 0.270 (6.9) 3.670 (93.2) 1.980 (50.3)
11 1.520 (38.6) 0.750 (19.1) 0.760 (19.3) 0.380 (9.7) 5.320 (135.1) 2.900 (73.7)
12 2.190 (55.6) 1.000 (25.4) 1.060 (26.9) 0.490 (12.4) 7.560 (192.0) 4.060 (103.1)
13 3.600 (91.4) 2.150 (54.6) 1.800 (45.7) 1.080 (27.4) 15.37 (390.4) 8.310 (211.1)
TABLE I: Dash Number and Dimensions (Continued from Above)
Dash
No.
S
(As Recovered)
Ref
U
(As Recovered)
±10%
T
(As Recovered)
±10%
HW
(As Recovered)
±20%
W
(As Recovered)
±20%
09 0.820 (20.8) 0.620 (15.7) 1.200 (30.5) 0.060 (1.5) 0.040 (1.0)
10 1.690 (42.9) 1.300 (33.0) 2.250 (57.2) 0.100 (2.5) 0.060 (1.5)
11 2.420 (61.5) 1.800 (45.7) 3.500 (88.9) 0.120 (3.0) 0.070 (1.8)
12 3.500 (88.9) 2.800 (71.1) 4.800 (121.9) 0.180 (4.6) 0.120 (3.0)
13 7.060 (179.3) 5.00 (127.0) 10.00 (254.0) 0.280 (7.1) 0.180 (4.6)
AS85049/142
1:3 Transition Wide Body Heat Shrink Boot
WHY GLENAIR?
Sales, service, and support professionals standing by…
when and where you need them
ONE GOOD REASON
TO SOURCE YOUR BACKSHELLS
FROM GLENAIR
GLENAIR, INC. • 1211 Air Way • Glendale, CA 91201-2497 • Tel: 818-247-6000 • Email: sales@glenair.com • www.glenair.com
OUTSTANDING CUSTOMER SERVICE
Outstanding
Customer Service!
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-38999
C
MIL-DTL-38999
Qualied Connector Accessories
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-38999
MIL-DTL-38999 MS27501
MS27502 MS20048
MS20047 660-012
660-013 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series I C-2
MIL-DTL-38999 MS27510
MS27511 MS27352
MS27353 660-014
660-015 Protective Plug Cover
Protective Receptacle Cover MIL-DTL-38999 Series II C-3
MIL-DTL-38999/22 D38999/22 –– 650HS010 Dummy Storage Receptacle, Threaded Coupling MIL-DTL-38999, Series III C-4
MIL-DTL-38999/28 D38999/28 –– Consult Factory Jam Nut with Safety Wire Holes MIL-DTL-38999 Series III & IV;
EN3645 C-5
MIL-DTL-38999/32
MIL-DTL-38999/33 D38999/32
D38999/33 –– 660-023
660-024 Composite or Metal Threaded Plug Cover
Composite or Metal Threaded Receptacle Cover MIL-DTL-38999, Series III C-6
MIL-DTL-38999/50 D38999/50 –– 650HS007 Dummy Storage Receptacle, Bayonet Coupling MIL-DTL-38999, Series IV C-7
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-38999
C
MS27501 and MS27502
Protective Plug and ReceptacleCovers
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
Gasket
J
G
MS27501 Plug Cover
.90 (22.9)
Max Attachment
.167 (4.2)
Dia
MS27502 Receptacle Cover MS27502
Attachment
Type N
Gasket
Attachment
Style C
.167 (4.2)
Dia
H
J
.82 (20.8)
Max
TABLE I: Shell Size, Attachment and Dimensions
Shell
Size G Dia
Max H
Max J Attachment
Length (Inches) K Dia
Min
9 .820 (20.8) .820 (20.8) 3.000 (76.2) .700 (17.8)
11 .940 (23.9) .940 (23.9) 3.000 (76.2) .840 (21.3)
13 1.070 (27.2) 1.100 (27.9) 3.500 (88.9) 1.010 (25.7)
15 1.190 (30.2) 1.220 (31.0) 3.500 (88.9) 1.140 (29.0)
17 1.320 (33.5) 1.340 (34.0) 3.500 (88.9) 1.260 (32.0)
19 1.440 (36.6) 1.460 (37.1) 3.500 (88.9) 1.390 (35.3)
21 1.570 (39.9) 1.580 (40.1) 4.000 (101.6) 1.510 (38.4)
23 1.690 (42.9) 1.700 (43.2) 4.000 (101.6) 1.640 (41.7)
25 1.820 (46.2) 1.830 (46.5) 4.000 (101.6) 1.760 (44.7)
Basic Part Number
MS27501 = Plug Cover
MS27502 = Receptacle Cover
MS27501 B 19 C L
Shell
Size
Finish
A = Gold Iridite over Cadmium over Nickel
B = 500 Hour Cadmium Olive Drab
C = Anodize
F = Electroless Nickel
T = Nickel Fluorocarbon Polymer
Z = Zinc Nickel
Attachment Option
A = No Attachment
C = Chain
N = Chain with Ring (MS27502 Only)
Length (Inches)
L = 5.0 (127.0)
M = 6.0 (152.4) MS27501 Only
N = 7.0 (177.8) MS27501 Only
(Omit for Standard)
MATING CONNECTOR
MIL-DTL-38999, Series I
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-38999
C
MS27510 and MS27511
Protective Plug and ReceptacleCovers
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
TABLE I: Shell Size, Attachment and Dimensions
Shell
Size
G Dia
Max
H Dia
Max
J Std.
Chain or
Rope Length
K Dia
Min
8 .720 (18.3) .630 (16.0) 3.000 (76.2) .890 (22.6)
10 .850 (21.6) .761 (19.3) 3.000 (76.2) 1.010 (25.7)
12 1.000 (25.4) .936 (23.8) 3.500 (88.9) 1.140 (29.0)
14 1.130 (28.7) 1.074 (27.3) 3.500 (88.9) 1.260 (32.0)
16 1.250 (31.8) 1.172 (29.8) 3.500 (88.9) 1.390 (35.3)
18 1.380 (35.1) 1.304 (33.1) 3.500 (88.9) 1.510 (38.4)
20 1.500 (38.1) 1.435 (36.4) 4.000 (101.6) 1.640 (41.7)
22 1.630 (41.4) 1.560 (39.6) 4.000 (101.6) 1.760 (44.7)
24 1.750 (44.5) 1.688 (42.9) 4.000 (101.6) 1.890 (48.0)
Basic Part Number
MS27510 = Plug Cover
MS27511 = Receptacle Cover
MS27511 B 19 C L
Shell
Size
Attachment Option
A = No Attachment
C = Chain
N = Chain with Ring (MS27511 Only)
R = Rope (MS27511 Only)
Length (Inches)
L = 5.0 (127.0)
M = 6.0 (152.4) MS27510 Only
N = 7.0 (177.8) MS27510 Only
(Omit for Standard Length. Not Applicable
to Style R—MS27511 Only)
Gasket
Attachment
Style C
.167 (4.2)
Dia
H
MS27511 Receptacle Cover
J
.570 (14.5)
Max
K
MS27511
Attachment
Type N
Attachment
Style C
.167 (4.2)
Dia
Gasket
J
G
MS27510 Plug Cover
.570 (14.5)
Max
MATING CONNECTOR
MIL-DTL-38999, Series II
Finish
A = Gold Iridite over Cadmium over Nickel
B = 500 Hour Cadmium Olive Drab
C = Anodize
F = Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-38999
C
D38999/22
Dummy Stowage Receptacle
Threaded Coupling
TABLE I: Shell Size Code and Dimensions
Shell
Size Code
Shell
Size Ref.
A
Thread
B -0.0 C D
Max +.012 (0.3)
A
(See Note 4) 9.625-.1P-3LTS .820 (20.83) .098 (2.5) .594 (15.09)
AA
(See Note 5) 9.625-.1P-3LTS .820 (20.83) .098 (2.5) .594 (15.09)
B11 .750-.1P-3LTS .820 (20.83) .098 (2.5) .719 (18.26)
C 13 .875-.1P-3LTS .820 (20.83) .098 (2.5) .812 (20.62)
D 15 1.000-.1P-3LTS .820 (20.83) .098 (2.5) .906 (23.01)
E 17 1.187-.1P-3LTS .820 (20.83) .098 (2.5) .969 (24.61)
F 19 1.250-.1P-3LTS .820 (20.83) .098 (2.5) 1.062 (26.97)
G 21 1.375-.1P-3LTS .790 (20.07) .126 (3.2) 1.156 (29.36)
H 23 1.500-.1P-3LTS .790 (20.07) .126 (3.2) 1.250 (31.75)
J 25 1.625-.1P-3LTS .790 (20.07) .126 (3.2) 1.375 (34.93)
Basic
Part No.
D38999/22 B W
Shell
Size Code
MATING CONNECTOR
MIL-DTL-38999 Series III
TABLE I: Shell Size Code and Dimensions
Shell
Size Code
Shell
Size Ref. EF -0.0 Ø G
+.012 (0.3) +.008 (0.2)
A 9 .719 (18.26) .937 (23.8) .128 (3.25)
B11 .812 (20.62) 1.031 (26.2) .128 (3.25)
C 13 .906 (23.01) 1.126 (28.6) .128 (3.25)
D 15 .969 (24.61) 1.220 (31.0) .128 (3.25)
E 17 1.062 (26.97) 1.311 (33.3) .128 (3.25)
F 19 1.156 (29.36) 1.437 (36.5) .128 (3.25)
G 21 1.250 (31.75) 1.563 (39.7) .128 (3.25)
H 23 1.375 (34.93) 1.689 (42.9) .154 (3.91)
J 25 1.500 (38.10) 1.811 (46.0) .154 (3.91)
APPLICATION NOTES
1. Assembly to be identied with
manufacturer’s name and part number,
space permitting.
2. For complete dimensions, see the
applicable Military Specication.
3. Metric dimensions (mm) are in
parentheses.
4. Shell size code “A” is for polarization C, E
and N only.
5. Shell size code “AA” is for polarization A, B
and D only.
F Sq.
G Dia
A Thread
B
E Typ.
D Typ.
C
Class per Spec
C = Aluminum Anodize
F = Aluminum, Electroless Nickel
H = Stainless Steel, Passivated (Space Grade)
J = Composite, Cadmium Plated, Olive Drab
K = Corrosion-Resistant Steel Passivate
M = Composite, Electroless Nickel Plated
N = Stainless Steel, Electrodeposited Nickel
Y = Stainless Steel, Passivated
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-38999
C
D38999/28
Jam Nut
CB
A Thread
Safety Wire
Holes (Min. 3
Holes Equally
Spaced)
CONNECTOR DESIGNATOR:
HMIL-DTL-38999
Series III and IV, EN3645
TABLE I: Reference for Connector Shell Size
Dash
No.
Shell Size A Thread
Class 2B B Hex
Max
C
Series
III Series
IV ±.018
-.000 (.45)
(.00)
1 9 -- M17 X 1 - 6H* .945 (24.00) .125 (3.17)
211 -- M20 X 1 - 6H* 1.063 (27.00) .125 (3.17)
3 13 11 M25 X 1 - 6H 1.260 (32.00) .125 (3.17)
4 15 13 M28 X 1 - 6H 1.417 (36.00) .125 (3.17)
5 -- 15 M31 X 1 - 6H 1.614 (41.00) .125 (3.17)
6 17 -- M32 X 1 - 6H 1.457 (37.00) .125 (3.17)
7 -- 17 M34 X 1 - 6H 1.614 (41.00) .125 (3.17)
8 19 -- M35 X 1 - 6H 1.614 (41.00) .125 (3.17)
9 21 19 M38 X 1 - 6H 1.811 (46.00) .125 (3.17)
10 23 21 M41 X 1 - 6H 1.969 (50.00) .125 (3.17)
11 25 23 M44 X 1 - 6H 2.017 (51.23) .125 (3.17)
12 -- 25 M47 X 1 - 6H 2.165 (55.00) .125 (3.17)
*Modied Minor Diameter
Material and Finish
C = Aluminum Anodize
F = Aluminum, Electroless Nickel
K = Corrosion-Resistant Steel Passivate
W = Aluminum, Cadmium Olive Drab over
Electroless Nickel
Basic
Part Number
D38999/28 -11 A
Dash No.
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-38999
C
D38999/32 and D38999/33
Composite or Metal Protective Covers
Plug and Receptacle • MIL-DTL-38999 Series III Threaded
TABLE I: Shell Size, Thread and Dimensions
Shell
Size
E
Thread
F
Max
G
Max
H
Min
J
Min
9.6250-0.1P-0.3L-TS .906 (23.0) .906 (23.0) .694 (17.6) .512 (13.0)
11 .7500-0.1P-0.3L-TS 1.024 (26.0) 1.102 (28.0) .865 (22.0) .709 (18.0)
13 .8750-0.1P-0.3L-TS 1.220 (31.0) 1.220 (31.0) .989 (25.1) .787 (20.0)
15 1.0000-0.1P-0.3L-TS 1.300 (33.0) 1.260 (32.0) 1.178 (29.9) .906 (23.0)
17 1.1875-0.1P-0.3L-TS 1.457 (37.0) 1.457 (37.0) 1.260 (32.0) 1.024 (26.0)
19 1.2500-0.1P-0.3L-TS 1.575 (40.0) 1.535 (39.0) 1.428 (36.3) 1.142 (29.0)
21 1.3750-0.1P-0.3L-TS 1.732 (44.0) 1.654 (42.0) 1.506 (38.3) 1.260 (32.0)
23 1.5000-0.1P-0.3L-TS 1.811 (46.0) 1.772 (45.0) 1.678 (42.6) 1.339 (34.0)
25 1.6250-0.1P-0.3L-TS 1.969 (50.0) 1.929 (49.0) 1.750 (44.5) 1.535 (39.0)
Basic Part Number
D38999/32 = Plug Cover
D38999/33 = Receptacle Cover
D38999/32 W 15 N
Shell Size
Designator
Attachment Style
R or N
APPLICATION NOTES
1. Assembly identied with
manufacturer’s name
and part number, space
permitting.
2. For complete dimensions,
see the applicable Military
Specication.
3. Metric dimensions (mm)
are in parentheses.
Style R
.167 (4.2)
Dia.
Gasket
F
J Dia
D38999/32
PLUG COVER
1.18 (30.0) Max
E Thread
Style N
Length
**
Style R
.167 (4.2)
Dia.
Gasket
G
H Dia
D38999/33
RECEPTACLE COVER
.906 (23.0) Max
E Thread
Style N
Length
**
** Rope Length
5.000 (127.0)
+.50 (+13.0)
-.25 (-7.0)
MATING CONNECTOR
MIL-DTL-38999, Series III Threaded
Material and Finish
C = Aluminum, Hard Anodize
F = Aluminum, Electroless Nickel
H = Stainless Steel, Passivated (Space Grade)
J = Composite, Cadmium, Olive Drab
K = Stainless Steel, Passivated
M = Composite, Electroless Nickel
N = Stainless Steel, Electrodeposited Nickel
T = Aluminum, Nickel Fluorocarbon Polymer
W = Aluminum, Cadmium Olive Drab
Z = Aluminum, Black Zinc-Nickel
Rev. 10.19.18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
C-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-38999
C
D38999/50
Dummy Stowage Receptacle
Bayonet Coupling
A Sq.
B Sq.
E
D
C
.819/.756
(20.8/19.2)
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell
Size Code
Shell
Size Ref.
AB
BSC
C D Ø E
+ 0 (0.00) ±.010 (±0.25) ±.008 (±0.2)
±.043 (±1.10) -.015 (-0.39)
B11 1.030 (26.15) .812 (20.62) .793 (20.15) .093 (2.35) .130 (3.3)
C 13 1.124 (28.55) .906 (23.02) .919 (23.35) .093 (2.35) .130 (3.3)
D 15 1.219 (30.95) .969 (24.62) 1.044 (26.52) .093 (2.35) .130 (3.3)
E 17 1.313 (33.35) 1.062 (26.98) 1.170 (29.72) .093 (2.35) .130 (3.3)
F 19 1.439 (36.55) 1.156 (29.36) 1.294 (32.87) .093 (2.35) .130 (3.3)
G 21 1.561 (39.65) 1.250 (31.76) 1.419 (36.05) .124 (3.15) .130 (3.3)
H 23 1.687 (42.85) 1.375 (34.92) 1.544 (39.22) .124 (3.15) .150 (3.8)
J 25 1.813 (46.05) 1.500 (38.10) 1.669 (42.40) .124 (3.15) .150 (3.8)
MATING CONNECTOR
MIL-DTL-38999 Series IV
Basic
Part No.
D38999/50 B W
Shell
Size Code
Class Per Spec.
(Finish is Cadmium Olive Drab
over Electroles Nickel
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
WHY GLENAIR?
ANOTHER GOOD REASON
TO SOURCE YOUR BACKSHELLS
FROM GLENAIR
Technical support and application engineering is offered
nationwide by over 100 Glenair eld representatives
GLENAIR, INC. • 1211 Air Way • Glendale, CA 91201-2497 • Tel: 818-247-6000 • Email: sales@glenair.com • www.glenair.com
NATIONWIDE TECH SUPPORT
Paul Winkler
Glenair Northern California
Sales Group
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
MIL-DTL-28840
Qualied Backshells and Connector Accessories
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-28840/1 M28840/1 –– 620GS051 Straight Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-2
MIL-DTL-28840/2 M28840/2 –– 620GA051 90° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-3
MIL-DTL-28840/3 M28840/3 –– 620GB051 45° Non-Self-Locking Strain Relief “G”
MIL-DTL-28840 D-4
MIL-DTL-28840/4 M28840/4 –– –– Metal-Core Conduit “G”
MIL-DTL-28840 D-5
MIL-DTL-28840/5 M28840/5 –– –– Straight Backshell for Metal-Core Conduit “G”
MIL-DTL-28840 D-6
MIL-DTL-28840/6 M28840/6 A
M28840/6 B –– 390AB001
370 Series Strt. EMI/RFI Environmental Backshell, Style A
Straight Environmental Backshell, Style B “G”
MIL-DTL-28840 D-7
D-8
MIL-DTL-28840/7 M28840/7 –– 650GS001 Dummy Storage Receptacle, Threaded Coupling “G”
MIL-DTL-28840 D-9
MIL-DTL-28840/8 M28840/8-
M28840/8 A –– 390-061 90° Environmental Backshell, Style A
90° EMI/RFI Environmental Backshell, Style B “G”
MIL-DTL-28840 D-10
D-11
MIL-DTL-28840/9 M28840/9 B
M28840/9 A –– 390-061 45° Environmental Backshell, Style A
45° EMI/RFI Environmental Backshell “G”
MIL-DTL-28840 D-12
D-13
MIL-DTL-28840/13
MIL-DTL-28840/15 M28840/13
M28840/15 –– 660-010
660-011 Protective Threaded Receptacle Cover
Protective Threaded Plug Cover MIL-DTL-28840 D-14
MIL-DTL-28840/22 M28840/22 –– –– Metal-Core Conduit Bushing “G”
MIL-DTL-28840 D-15
MIL-DTL-28840/23 M28840/23 –– Consult Factory E Nut, Non-Self-Locking “G”
MIL-DTL-28840 D-16
MIL-DTL-28840/24 M28840/24 –– Consult Factory Gasket “G”
MIL-DTL-28840 D-17
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/1
Straight Non-Self-Locking Strain Relief
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Desig-
nator
Shell Size
Ref.
A Thread
Class 2B
B
Max
C
Max
D
Max
Cable Entry
Closed Open
A11 .750 - 20 UNEF 1.028 (26.1) 1.091 (27.7) .903 (22.9) .177 (4.5) .286 (7.3)
B 13 .875 - 20 UNEF 1.141 (29.0) 1.091 (27.7) .977 (24.8) .177 (4.5) .286 (7.3)
C 15 1.000 - 20 UNEF 1.263 (32.1) 1.091 (27.7) 1.151 (29.2) .250 (6.4) .416 (10.6)
D 17 1.125 - 18 UNEF 1.387 (35.2) 1.206 (30.6) 1.281 (32.5) .291 (7.4) .476 (12.1)
E 19 1.250 - 18 UNEF 1.513 (38.4) 1.320 (33.5) 1.406 (35.7) .348 (8.8) .626 (15.9)
F 23 1.438 - 18 UNEF 1.703 (43.3) 1.445 (36.7) 1.576 (40.0) .429 (10.9) .831 (21.1)
G 25 1.562 - 18 UNEF 1.825 (46.4) 1.570 (39.9) 1.666 (42.3) .523 (13.3) .956 (24.3)
H 29 1.875 - 16 UN 2.143 (54.4) 1.721 (43.7) 2.046 (52.0) .643 (16.3) 1.081 (27.5)
J 33 2.062 - 16 UNS 2.329 (59.2) 1.908 (48.5) 2.209 (56.1) .704 (17.9) 1.187 (30.1)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M28840/1 J W
Designator
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
A Thread
Cable
Entry
.228
(5.79)
Ref.
Telescoping Screw
and Lockwasher
Wire Holes
(3 Equally Spaced)
C
BD
Rev. 12.13.18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
MIL-DTL-28840/2
90° Non-Self-Locking Strain Relief
A Thread
C
E
F
Cable
Entry
.228
(5.79)
Ref.
Telescoping Screw
and Lockwasher
G
Wire Holes
(3 Equally
Spaced)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Desig-
nator Shell Size
Ref. A Thread
Class 2B C
Max E
Max F
Max G
Max Cable Entry
Min Max
A11 .750 - 20 UNEF 1.028 (26.1) 1.071 (27.2) .903 (22.9) .929 (23.6) .177 (4.5) .286 (7.3)
B 13 .875 - 20 UNEF 1.141 (29.0) 1.071 (27.2) .977 (24.8) .929 (23.6) .177 (4.5) .286 (7.3)
C 15 1.000 - 20 UNEF 1.263 (32.1) 1.280 (32.5) 1.151 (29.2) 1.056 (26.8) .250 (6.4) .416 (10.6)
D 17 1.125 - 18 UNEF 1.387 (35.2) 1.392 (35.4) 1.281 (32.5) 1.233 (31.3) .291 (7.4) .476 (12.1)
E 19 1.250 - 18 UNEF 1.513 (38.4) 1.517 (38.5) 1.406 (35.7) 1.296 (32.9) .348 (8.8) .626 (15.9)
F 23 1.438 - 18 UNEF 1.703 (43.3) 1.642 (41.7) 1.576 (40.0) 1.358 (34.5) .429 (10.9) .831 (21.1)
G 25 1.562 - 18 UNEF 1.825 (46.4) 1.767 (44.9) 1.666 (42.3) 1.420 (36.1) .523 (13.3) .956 (24.3)
H 29 1.875 - 16 UN 2.143 (54.4) 1.905 (48.4) 2.046 (52.0) 1.634 (41.5) .643 (16.3) 1.081 (27.5)
J 33 2.062 - 16 UNS 2.329 (59.2) 1.968 (50.0) 2.209 (56.1) 1.859 (47.2) .704 (17.9) 1.187 (30.1)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M28840/2 J W
Designator
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/3
45° Non-Self-Locking Strain Relief
A Thread
C
E
F
Cable
Entry
.228
(5.79)
Ref.
Telescoping Screw
and Lockwasher
G
Wire Holes
(3 Equally
Spaced)
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Desig-
nator Shell Size
Ref. A Thread
Class 2B C
Max E
Max F
Max G
Max Cable Entry
Min Max
A11 .750 - 20 UNEF 1.028 (26.1) 1.650 (41.9) .903 (22.9) .929 (23.6) .177 (4.5) .286 (7.3)
B 13 .875 - 20 UNEF 1.141 (29.0) 1.650 (41.9) .977 (24.8) .929 (23.6) .177 (4.5) .286 (7.3)
C 15 1.000 - 20 UNEF 1.263 (32.1) 1.765 (44.8) 1.151 (29.2) 1.056 (26.8) .250 (6.4) .416 (10.6)
D 17 1.125 - 18 UNEF 1.387 (35.2) 1.874 (47.6) 1.281 (32.5) 1.233 (31.3) .291 (7.4) .476 (12.1)
E 19 1.250 - 18 UNEF 1.513 (38.4) 1.918 (48.7) 1.406 (35.7) 1.296 (32.9) .348 (8.8) .626 (15.9)
F 23 1.438 - 18 UNEF 1.703 (43.3) 1.962 (49.8) 1.576 (40.0) 1.358 (34.5) .429 (10.9) .831 (21.1)
G 25 1.562 - 18 UNEF 1.825 (46.4) 2.006 (51.0) 1.666 (42.3) 1.420 (36.1) .523 (13.3) .956 (24.3)
H 29 1.875 - 16 UN 2.143 (54.4) 2.301 (58.4) 2.046 (52.0) 1.634 (41.5) .643 (16.3) 1.081 (27.5)
J 33 2.062 - 16 UNS 2.329 (59.2) 2.389 (60.7) 2.209 (56.1) 1.859 (47.2) .704 (17.9) 1.187 (30.1)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
Basic
Part Number
M28840/3 J W
Designator
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
M28840/4
Metal Core Conduit
Military
Designator
M28840/4 12 A C
Type Designator
A - Plain
B - Insulator Jacket
Material Type
C - Brass
E - Nickel-Iron Conduit
Conduit Size
Size Nominal Conduit
Inside Diameter
A Diameter
Over Shield
± . (.)
LB Diameter Max Over
Jacket
 . (.) . (.)
 ft.
Max.
. (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
 . (.) . (.) . (.)
Order Length
50 Ft. Max.
Conduit
Braid
Neoprene Jacket
A Dia
Nominal
Conduit
I.D.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
M28840/5
Backshell for Metal Core Conduit
Military
Designator Dash
Number
M28840/5 16 W A
Type Designator
A - EMI / Environmental
B - EMI / Environmental
Material Type
W - Aluminum, Cadmium Plate,
O.D. over Electroless Nickel
D - Corrosion Resistant Steel,
Cadmium Plate, Black
A Thread
C
D
Cable
RangeE
.50 (12.7)
Max
STYLE A - EMI/Non-Environmental
(Plain Conduit)
A Thread
C
D
Cable
RangeF
1.75
(44.5)
Max
O-Rings
STYLE B - EMI/Environmental
(Jacket Conduit)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
MIL-DTL-28840/6 Style A
Straight EMI/RFI Environmental Backshell
TABLE II: Dash Number, Shell Size, Dimensions and Cable Range
Dash
No. Shell
Size E
± .120 (3.0) F Ref
Dim G Ref
Dim Cable Range
Min Max
01 11 3.62 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
02 13 3.62 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
03 13 3.62 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
04 15 3.62 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
05 15 3.62 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
06 15 3.62 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
07 15 4.12 (104.6) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
08 17 4.12 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
09 17 4.12 (104.6) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
10 17 4.12 (104.6) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
11 19 4.12 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
12 19 4.12 (104.6) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
13 23 4.62 (117.3) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
14 23 4.62 (117.3) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
15 23 4.62 (117.3) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
16 25 4.62 (117.3) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
17 25 5.12 (130.0) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
18 25 5.12 (130.0) 1.593 (40.5) 2.093 (53.2) .875 (22.2) 1.250 (31.8)
19 25 5.12 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
20 29 5.12 (130.0) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
21 29 5.12 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
22 33 5.12 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
23 33 5.12 (130.0) 1.900 (48.3) 2.750 (69.9) 1.250 (31.8) 1.625 (41.3)
24 11 3.62 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
25 11 3.62 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
26 13 3.62 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
27 13 4.12 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
28 15 4.12 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown
are not intended for inspection
criteria.
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.028 (26.1)
13 .875 - 20 UNEF 1.141 (29.0)
15 1.000 - 20 UNEF 1.263 (32.1)
17 1.125 - 18 UNEF 1.387 (35.2)
19 1.250 - 18 UNEF 1.513 (38.4)
23 1.438 - 18 UNEF 1.703 (43.3)
25 1.562 - 18 UNEF 1.825 (46.4)
29 1.875 - 16 UN 2.143 (54.4)
33 2.062 - 16 UNS 2.329 (59.2)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
Basic
Part
Number
M28840/6 16 W A
Dash No.
(Table II) Style
A = EMI/Environmental
Material and Finish
D = Corrosion Resistant Steel, Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-8
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/6 Style B
Straight Environmental Backshell
Basic
Part Number
M28840/6 16 W B
Dash Number
(Table II) Style Designator
B = Environmental
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
TABLE I: Shell Size
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.030 (26.2)
13 .875 - 20 UNEF 1.140 (29.0)
15 1.000 - 20 UNEF 1.260 (32.0)
17 1.125 - 18 UNEF 1.390 (35.3)
19 1.250 - 18 UNEF 1.510 (38.4)
23 1.438 - 18 UNEF 1.700 (43.2)
25 1.563 - 18 UNEF 1.820 (46.2)
29 1.875 - 16 UN 2.140 (54.4)
33 2.063 - 16 UNS 2.330 (59.2)
TABLE II: Dash Number and Dimensions
Dash
No. Shell
Size Ref. E
± .12 (3.0) F Ref.
Dim G Ref.
Dim Cable Range
Min Max
01 11 3.620 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
02 13 3.620 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
03 13 3.620 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
04 15 3.620 (91.9) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
05 15 3.620 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
06 15 3.620 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
07 15 4.120 (104.6) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
08 17 4.120 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
09 17 4.120 (104.6) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
10 17 4.120 (104.6) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
11 19 4.120 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
12 19 4.120 (104.6) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
13 23 4.620 (117.3) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
14 23 4.620 (117.3) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
15 23 4.620 (117.3) 1.593 (40.5) 2.003 (50.9) .812 (20.6) 1.188 (30.2)
16 25 4.620 (117.3) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
17 25 5.120 (130.0) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
18 25 5.120 (130.0) 1.593 (40.5) 2.093 (53.2) .875 (22.2) 1.250 (31.8)
19 25 5.120 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
20 29 5.120 (130.0) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
21 29 5.120 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
22 33 5.120 (130.0) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
23 33 5.120 (130.0) 1.900 (48.3) 2.750 (69.9) 1.250 (31.8) 1.625 (41.3)
24 11 3.620 (91.9) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
25 11 3.620 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
26 13 3.620 (91.9) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
27 13 4.120 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
28 15 4.120 (104.6) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as the
accommodation range for the wire
bundle or cable. Dimensions shown are
not intended for inspection criteria.
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-9
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
M28840/7
Dummy Stowage Receptacle
Threaded Coupling
D Dia
4 Holes
.898 / .878
(22.8 / 22.3) .130 / .100
(3.3 / 2.5)
C
B
A Thread
MATING CONNECTOR
MIL-DTL-28840
Basic
Part No.
M28840/7 G 1
Shell Size
Designator
Key Positions
(1, 2, 3, 4, 5, or 6)
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell Size
Designator Shell
Size Ref. E
Thread B
Dim C
Max D
Max
A11 0.750-0.1P-0.2L-DS .750 (19.1) 1.043 (26.5) .130 (3.3)
B 13 0.875-0.1P-0.2L-DS .843 (21.4) 1.158 (29.4) .130 (3.3)
C 15 1.062-0.1P-0.2L-DS .968 (24.6) 1.278 (32.5) .130 (3.3)
D 17 1.125-0.1P-0.2L-DS 1.015 (25.8) 1.403 (35.6) .130 (3.3)
E 19 1.312-0.1P-0.2L-DS 1.140 (29.0) 1.528 (38.8) .130 (3.3)
F 23 1.500-0.1P-0.2L-DS 1.281 (32.5) 1.738 (44.1) .130 (3.3)
G 25 1.625-0.1P-0.2L-DS 1.392 (35.4) 1.838 (46.7) .157 (4.0)
H 29 1.812-0.1P-0.2L-DS 1.568 (39.8) 2.158 (54.8) .157 (4.0)
J 33 2.000-0.1P-0.2L-DS 1.734 (44.0) 2.348 (59.6) .183 (4.6)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Material/Finish: Aluminum Alloy/Cadmium Olive Drab.
4. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/8 Style A
90° EMI/RFI Environmental Backshell
TABLE II: Dash Number, Shell Size, Dimensions and Cable Range
Dash
No. Shell
Size E Max
Envelope F
Max G Ref
Dim Cable Range
Min Max
01 11 2.614 (66.4) 5.332 (135.4) .938 (23.8) .188 (4.8) .312 (7.9)
02 13 2.614 (66.4) 5.332 (135.4) .938 (23.8) .188 (4.8) .312 (7.9)
03 13 2.614 (66.4) 5.332 (135.4) 1.125 (28.6) .281 (7.1) .438 (11.1)
04 15 2.864 (72.7) 5.457 (138.6) .938 (23.8) .188 (4.8) .312 (7.9)
05 15 2.864 (72.7) 5.457 (138.6) 1.125 (28.6) .281 (7.1) .438 (11.1)
06 15 2.864 (72.7) 5.457 (138.6) 1.312 (33.3) .344 (8.7) .562 (14.3)
07 15 3.114 (79.1) 5.682 (144.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
08 17 3.114 (79.1) 5.682 (144.3) 1.312 (33.3) .375 (9.5) .625 (15.9)
09 17 3.114 (79.1) 5.713 (145.1) 1.593 (40.5) .438 (11.1) .750 (19.1)
10 17 3.114 (79.1) 5.807 (147.5) 1.750 (44.5) .625 (15.9) .938 (23.8)
11 19 3.114 (79.1) 5.682 (144.3) 1.312 (33.3) .375 (9.5) .625 (15.9)
12 19 3.364 (85.4) 5.832 (148.1) 1.750 (44.5) .625 (15.9) .938 (23.8)
13 23 3.364 (85.4) 5.738 (145.7) 1.593 (40.5) .438 (11.1) .750 (19.1)
14 23 3.364 (85.4) 5.832 (148.1) 1.750 (44.5) .625 (15.9) .938 (23.8)
15 23 3.364 (85.4) 6.019 (152.9) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
16 25 3.364 (85.4) 5.832 (148.1) 1.750 (44.5) .625 (15.9) .938 (23.8)
17 25 3.364 (85.4) 6.019 (152.9) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
18 25 3.614 (91.8) 6.144 (156.1) 2.093 (53.2) .875 (22.2) 1.250 (31.8)
19 25 3.614 (91.8) 6.176 (156.9) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
20 29 3.614 (91.8) 6.144 (156.1) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
21 29 3.614 (91.8) 6.176 (156.9) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
22 33 4.114 (104.5) 6.426 (163.2) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
23 33 4.114 (104.5) 6.701 (170.2) 2.750 (69.9) 1.250 (31.8) 1.625 (41.3)
24 11 2.614 (66.4) 5.332 (135.4) 1.125 (28.6) .281 (7.1) .438 (11.1)
25 11 2.864 (72.7) 5.457 (138.6) 1.312 (33.3) .344 (8.7) .562 (14.3)
26 13 2.864 (72.7) 5.457 (138.6) 1.312 (33.3) .344 (8.7) .562 (14.3)
27 13 3.114 (79.1) 5.682 (144.3) 1.312 (33.3) .375 (9.5) .625 (15.9)
28 15 3.114 (79.1) 5.682 (144.3) 1.312 (33.3) .375 (9.5) .625 (15.9)
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range for the wire bundle or
cable. Dimensions shown are not intended for inspection criteria.
TABLE I: Shell Size and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.028 (26.1)
13 .875 - 20 UNEF 1.141 (29.0)
15 1.000 - 20 UNEF 1.263 (32.1)
17 1.125 - 18 UNEF 1.387 (35.2)
19 1.250 - 18 UNEF 1.513 (38.4)
23 1.438 - 18 UNEF 1.703 (43.3)
25 1.562 - 18 UNEF 1.825 (46.4)
29 1.875 - 16 UN 2.143 (54.4)
33 2.062 - 16 UNS 2.329 (59.2)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
Basic
Part
Number
M28840/8 16 W A
Dash No.
(Table II) Style
A = EMI/Environmental
Material and Finish
D = Corrosion Resistant Steel, Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-11
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
MIL-DTL-28840/8 Style B
90° Environmental Backshell
TABLE II: Dash Number and Dimensions
Dash
No. Shell
Size Ref. E Max
Envelope F
Max G Ref.
Dim Cable Range
Min Max
01 11 2.614 (66.4) 2.962 (75.2) .938 (23.8) .188 (4.8) .312 (7.9)
02 13 2.614 (66.4) 2.962 (75.2) .938 (23.8) .188 (4.8) .312 (7.9)
03 13 2.614 (66.4) 2.962 (75.2) 1.125 (28.6) .281 (7.1) .438 (11.1)
04 15 2.864 (72.7) 3.087 (78.4) .938 (23.8) .188 (4.8) .312 (7.9)
05 15 2.864 (72.7) 3.087 (78.4) 1.125 (28.6) .281 (7.1) .438 (11.1)
06 15 2.864 (72.7) 3.087 (78.4) 1.312 (33.3) .344 (8.7) .562 (14.3)
07 15 3.114 (79.1) 3.312 (84.1) 1.593 (40.5) .438 (11.1) .750 (19.1)
08 17 3.114 (79.1) 3.312 (84.1) 1.312 (33.3) .375 (9.5) .625 (15.9)
09 17 3.114 (79.1) 3.343 (84.9) 1.593 (40.5) .438 (11.1) .750 (19.1)
10 17 3.114 (79.1) 3.437 (87.3) 1.750 (44.5) .625 (15.9) .938 (23.8)
11 19 3.114 (79.1) 3.312 (84.1) 1.312 (33.3) .375 (9.5) .625 (15.9)
12 19 3.364 (85.4) 3.462 (87.9) 1.750 (44.5) .625 (15.9) .938 (23.8)
13 23 3.364 (85.4) 3.368 (85.5) 1.593 (40.5) .438 (11.1) .750 (19.1)
14 23 3.364 (85.4) 3.462 (87.9) 1.750 (44.5) .625 (15.9) .938 (23.8)
15 23 3.364 (85.4) 3.649 (92.7) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
16 25 3.364 (85.4) 3.462 (87.9) 1.750 (44.5) .625 (15.9) .938 (23.8)
17 25 3.364 (85.4) 3.649 (92.7) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
18 25 3.614 (91.8) 3.774 (95.9) 2.093 (53.2) .875 (22.2) 1.250 (31.8)
19 25 3.614 (91.8) 3.806 (96.7) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
20 29 3.614 (91.8) 3.774 (95.9) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
21 29 3.614 (91.8) 3.806 (96.7) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
22 33 4.114 (104.5) 4.056 (103.0) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
23 33 4.114 (104.5) 4.331 (110.0) 2.750 (69.9) 1.250 (31.8) 1.625 (41.3)
24 11 2.614 (66.4) 2.962 (75.2) 1.125 (28.6) .281 (7.1) .438 (11.1)
25 11 2.864 (72.7) 3.087 (78.4) 1.312 (33.3) .344 (8.7) .562 (14.3)
26 13 2.864 (72.7) 3.087 (78.4) 1.312 (33.3) .344 (8.7) .562 (14.3)
27 13 3.114 (79.1) 3.312 (84.1) 1.312 (33.3) .375 (9.5) .625 (15.9)
28 15 3.114 (79.1) 3.312 (84.1) 1.312 (33.3) .375 (9.5) .625 (15.9)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
TABLE I: Shell Size
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.030 (26.2)
13 .875 - 20 UNEF 1.140 (29.0)
15 1.000 - 20 UNEF 1.260 (32.0)
17 1.125 - 18 UNEF 1.390 (35.3)
19 1.250 - 18 UNEF 1.510 (38.4)
23 1.438 - 18 UNEF 1.700 (43.2)
25 1.563 - 18 UNEF 1.820 (46.2)
29 1.875 - 16 UN 2.140 (54.4)
33 2.063 - 16 UNS 2.330 (59.2)
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range
for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
Basic
Part Number
M28840/8 16 W B
Dash Number
(Table II) Style Designator
B = Environmental
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-12
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/9 Style A
45° EMI/RFI Environmental Backshell
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Metric dimensions (mm) are in
parentheses.
3. Cable Range is dened as
the accommodation range
for the wire bundle or cable.
Dimensions shown are not
intended for inspection criteria.
TABLE I: Shell Size
and Dimensions
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.028 (26.1)
13 .875 - 20 UNEF 1.141 (29.0)
15 1.000 - 20 UNEF 1.263 (32.1)
17 1.125 - 18 UNEF 1.387 (35.2)
19 1.250 - 18 UNEF 1.513 (38.4)
23 1.438 - 18 UNEF 1.703 (43.3)
25 1.562 - 18 UNEF 1.825 (46.4)
29 1.875 - 16 UN 2.143 (54.4)
33 2.062 - 16 UNS 2.329 (59.2)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
Basic
Part
Number
M28840/9 16 W A
Dash No.
(Table II) Style
A = EMI/Environmental
Material and Finish
D = Corrosion Resistant Steel, Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-13
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
MIL-DTL-28840/9
45° Environmental Backsheli Style B
TABLE I: Shell Size
Shell
Size A Thread
Class 2B C Dia
Max
11 .750 - 20 UNEF 1.030 (26.2)
13 .875 - 20 UNEF 1.140 (29.0)
15 1.000 - 20 UNEF 1.260 (32.0)
17 1.125 - 18 UNEF 1.390 (35.3)
19 1.250 - 18 UNEF 1.510 (38.4)
23 1.438 - 18 UNEF 1.700 (43.2)
25 1.563 - 18 UNEF 1.820 (46.2)
29 1.875 - 16 UN 2.140 (54.4)
33 2.063 - 16 UNS 2.330 (59.2)
TABLE II: Dash Number, Dimensions and Cable Range
Dash
No. Shell
Size Ref. E
Max F Ref.
Dim G Ref.
Dim Cable Range
Min Max
01 11 1.031 (26.2) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
02 13 1.031 (26.2) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
03 13 1.031 (26.2) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
04 15 1.156 (29.4) 1.281 (32.5) .938 (23.8) .188 (4.8) .312 (7.9)
05 15 1.156 (29.4) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
06 15 1.156 (29.4) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
07 15 1.281 (32.5) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
08 17 1.281 (32.5) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
09 17 1.281 (32.5) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
10 17 1.281 (32.5) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
11 19 1.281 (32.5) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
12 19 1.406 (35.7) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
13 23 1.406 (35.7) 1.312 (33.3) 1.593 (40.5) .438 (11.1) .750 (19.1)
14 23 1.406 (35.7) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
15 23 1.406 (35.7) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
16 25 1.406 (35.7) 1.406 (35.7) 1.750 (44.5) .625 (15.9) .938 (23.8)
17 25 1.406 (35.7) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
18 25 1.531 (38.9) 1.593 (40.5) 2.093 (53.2) .875 (22.2) 1.250 (31.8)
19 25 1.531 (38.9) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
20 29 1.531 (38.9) 1.593 (40.5) 2.093 (53.2) .812 (20.6) 1.188 (30.2)
21 29 1.531 (38.9) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
22 33 1.781 (45.2) 1.625 (41.3) 2.343 (59.5) 1.000 (25.4) 1.380 (35.1)
23 33 1.781 (45.2) 1.900 (48.3) 2.750 (69.9) 1.250 (31.8) 1.625 (41.3)
24 11 1.031 (26.2) 1.281 (32.5) 1.125 (28.6) .281 (7.1) .438 (11.1)
25 11 1.156 (29.4) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
26 13 1.156 (29.4) 1.281 (32.5) 1.312 (33.3) .344 (8.7) .562 (14.3)
27 13 1.281 (32.5) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
28 15 1.281 (32.5) 1.281 (32.5) 1.312 (33.3) .375 (9.5) .625 (15.9)
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
Basic
Part Number
M28840/9 16 W B
Dash Number
(Table II) Style Designator
B = Environmental
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
APPLICATION NOTES
1. For complete dimensions see the applicable Military
Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range
for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-14
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
M28840/13 and M28840/15
Protective Plug and Receptacle Covers
M28840/15 Plug Cover
1.000 (25.4)
Max
5.0
(127.0)
F
F
Gasket
M28840/13 Receptacle Cover
Attachment
Style A
.156 (4.0)
Dia
E Thread E Thread
.780 (19.8)
Max
5.0
(127.0)
Attachment
Style A
J Dia
H for Type B
K for Type C
M28840/13 Attachment Types B & C
G
MS28840/15 Attachment Type B
APPLICATION NOTES
1. Assembly identied with
manufacturer’s name
and part number, space
permitting.
2. For complete dimensions,
see the applicable Military
Specication.
3. Metric dimensions (mm)
are in parentheses.
Basic Part Number
M28840/13 = Receptacle Cover
M28840/15 = Plug Cover
M28840/13 H A W
Shell Size
Designator
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, 500 Hour, Cadmium O.D.
Attachment Style
A = Chain with Fastener
B = Chain with Ring for Jam Nut Receptacle (M28840/13 Only)
B = Chain with Ring (M28840/15 Only)
C = Chain with Ring for Cable Receptacle (M28840/13 Only)
TABLE I: Shell Size Designator, Thread and Dimensions
Shell Size
Desig. Shell Size
Ref. E
Thread F
Max G Dia
± .010 (0.3) H Dia
± .010 (0.3) J Dia
± .005 (0.1) K Dia
± .010 (0.3)
A11 0.750-0.1P-0.2L-DS 1.028 (26.1) .765 (19.4) .890 (22.6) .130 (3.3) .765 (19.4)
B 13 0.875-0.1P-0.2L-DS 1.141 (29.0) .890 (22.6) 1.015 (25.8) .130 (3.3) .890 (22.6)
C 15 1.062-0.1P-0.2L-DS 1.263 (32.1) 1.015 (25.8) 1.203 (30.6) .130 (3.3) 1.015 (25.8)
D 17 1.125-0.1P-0.2L-DS 1.387 (35.2) 1.140 (29.0) 1.265 (32.1) .130 (3.3) 1.140 (29.0)
E 19 1.312-0.1P-0.2L-DS 1.513 (38.4) 1.265 (32.1) 1.453 (36.9) .130 (3.3) 1.265 (32.1)
F 23 1.500-0.1P-0.2L-DS 1.703 (43.3) 1.453 (36.9) 1.640 (41.7) .130 (3.3) 1.453 (36.9)
G 25 1.625-0.1P-0.2L-DS 1.825 (46.4) 1.577 (40.1) 1.765 (44.8) .156 (4.0) 1.577 (40.1)
H 29 1.812-0.1P-0.2L-DS 2.143 (54.4) 1.890 (48.0) 1.953 (49.6) .156 (4.0) 1.890 (48.0)
J 33 2.000-0.1P-0.2L-DS 2.329 (59.2) 2.077 (52.8) 2.140 (54.4) .193 (4.9) 2.077 (52.8)
MATING CONNECTOR
MIL-DTL-28840
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-15
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
M28840/22
Metal Core Conduit Bushing
Size
MIL-
DTL-/
Size Ref.
A
+. (.)
-. (.)
B
+. (.)
-. (.)
C
+. (.)
-. (.)
D
+. (.)
-. (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
  . (.) . (.) . (.) . (.)
Dash Number
M28840/22 S A
Military
Designator
Material Designator
S - Corrosion resistant steel
Passivate IAW SAE-AMS-QQ-P-35
1.50 (38.1)
± .03 (.8)
D
DiaA
DiaB
DiaC
Dia
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-16
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-28840
D
MIL-DTL-28840/23
Non-Self-Locking E-Nut
CONNECTOR DESIGNATOR:
GMIL-DTL-28840
A Thread
B
.228
(5.8)
Ref.
.718 (18.2)
± .062 (1.6)
Ring
Clearance Hole For .032 (.8) Dia.
Safety Wire (3 Places 120° Apart)
Captive
Coupling Nut
TABLE I: Shell Size, Shell Size Ref,
Thread and Dimensions
Shell
Size Shell Size
Ref. A Thread
Class 2B Ø B
Max
A 11 .750 - 20 UNEF 1.028 (26.1)
B 13 .875 - 20 UNEF 1.141 (29.0)
C 15 1.000 - 20 UNEF 1.263 (32.1)
D 17 1.125 - 18 UNEF 1.387 (35.2)
E 19 1.250 - 18 UNEF 1.513 (38.4)
F 23 1.438 - 18 UNEF 1.703 (43.3)
G 25 1.562 - 18 UNEF 1.825 (46.4)
H 29 1.875 - 16 UN 2.143 (54.4)
J 33 2.062 - 16 UNS 2.329 (59.2)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part
number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire
bundle or cable. Dimensions shown are not intended for inspection
criteria.
4. Metric dimensions (mm) are in parentheses.
Material and Finish
D = Corrosion Resistant Steel,
Cadmium Plate, Black
W = Aluminum, Cadmium Olive Drab
Basic Part
Number
M28840/23 -J W
Shell
Size
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
D-17
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-28840
D
M28840/24
Gasket
A
Square
C Square
D Dia
(4 Places)
B Dia
Material
A = Florinated Silicone
B = EMI Shielding - Rubber
Basic
Part Number
M28840/24 G A
Designator
TABLE I: Reference for Connector Shell Size
Designator Shell
Size A Sq. Ø B C Sq. Ø D
±.010 (.3) ±.008 (.2) ±.008 (.2) ±.010 (.3)
A11 .750 (19.1) .758 (19.3) 1.031 (26.2) .120 (3.0)
B 13 .843 (21.4) .883 (22.4) 1.146 (29.1) .120 (3.0)
C 15 .968 (24.6) 1.070 (27.2) 1.266 (32.2) .120 (3.0)
D 17 1.015 (25.8) 1.133 (28.8) 1.391 (35.3) .120 (3.0)
E 19 1.140 (29.0) 1.320 (33.5) 1.516 (38.5) .120 (3.0)
F 23 1.281 (32.5) 1.508 (38.3) 1.726 (43.8) .120 (3.0)
G 25 1.392 (35.4) 1.633 (41.5) 1.826 (46.4) .147 (3.7)
H 29 1.568 (39.8) 1.883 (47.8) 2.146 (54.5) .147 (3.7)
J 33 1.734 (44.0) 2.070 (52.6) 2.336 (59.3) .173 (4.4)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
WHY GLENAIR?
ANOTHER GOOD REASON
TO SOURCE YOUR BACKSHELLS
FROM GLENAIR
Glenair supplies every active MS backshell and connector
accessory—no gaps—most with same-day availability
GLENAIR, INC. • 1211 Air Way • Glendale, CA 91201-2497 • Tel: 818-247-6000 • Email: sales@glenair.com • www.glenair.com
“NO GAPS”
Innovation and Availability:
The Glenair Connector
Accessory Product Line
G
The Largest and Most Diverse Selection of Cylindrical
and Rectangular Connector Accessories in the World!
Glenair has the manufacturing capacity, raw materials, skilled operators, and
necessary approvals to produce every military-standard and commercial
connector accessory in use today. Tens of thousands of stock parts are staged
for immediate, same-day shipment. Special order lead-times are just 2-3 weeks.
Every Connector Accessory There Is!
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-83723
E
MIL-DTL-83723
Qualied Backshells and Connector Accessories
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
MIL-DTL-83723/27 M83723/27M –– 310KS002 Straight Shrink Boot Adapter “K”
MIL-DTL-83723 Series II E-2
MIL-DTL-83723/35 M83723/35S
M83723/35A
M83723/35N –– Consult Factory Strt. Non-Environmental Strain Relief Backshell
90° Non-Environmental Strain Relief Backshell
Non-Self-Locking E-Nut “K”
MIL-DTL-83723 Series II
E-3
E-4
E-5
MIL-DTL-83723/50 M83723/50 R
M83723/50 B
M83723/50 A –– Consult Factory Straight Qwik-Ty® Strain Relief
45° Qwik-Ty® Strain Relief
90° Qwik-Ty® Strain Relief K”
MIL-DTL-83723 Series II E-6
MIL-DTL-83723/59
MIL-DTL-83723/60 M83723/59-1
M83723/60-1 MS27292
MS27293 660-021
660-022 Protective Plug Cover, Threaded Coupling
Protective Receptacle Cover, Threaded Coupling MIL-DTL-83723, Series III E-7
MIL-DTL-83723/59
MIL-DTL-83723/60 M83723/59-2
M83723/60-2 MS27294
MS27295 660-019
660-020 Protective Plug Cover Bayonet Coupling
Protective Receptacle Cover Bayonet Coupling MIL-DTL-83723, Series III E-8
MIL-DTL-83723/70 M83723/70 –– Consult Factory Straight Quick Disconnect Receptacle Adapter –– E-9
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-83723
E
M83723/27M
Straight Shrink Boot Adapter
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Finish: Electroless Nickel.
3. Metric dimensions (mm)
are in parentheses.
Shell
Size
Basic
Part Number
M83723/27M 22 M
Backshell
Only
TABLE I: Adapter Size, Shell Size, Thread and Dimensions
Adapter
Size Shell Size
Ref. A Thread
Class 2B B Dia
Max E
Dia F Dia
Min G
Max
08 8S .438 - 28 UNEF .580 (14.7) .250 (6.4) .479 (12.2) .830 (21.1)
10 10S .500 - 28 UNEF .640 (16.3) .303 (7.7) .539 (13.7) .830 (21.1)
11 10SL .562 - 24 UNEF .700 (17.8) .383 (9.7) .608 (15.4) .830 (21.1)
12 12 .625 - 24 UNEF .760 (19.3) .408 (10.4) .659 (16.7) .830 (21.1)
13 12S .625 - 24 UNEF .760 (19.3) .408 (10.4) .659 (16.7) .830 (21.1)
14 14 .750 - 20 UNEF .890 (22.6) .490 (12.4) .782 (19.9) .830 (21.1)
16 14S .750 - 20 UNEF .890 (22.6) .490 (12.4) .782 (19.9) .830 (21.1)
16 16 .875 - 20 UNEF 1.010 (25.7) .609 (15.5) .908 (23.1) .996 (25.3)
17 16S .875 - 20 UNEF 1.010 (25.7) .609 (15.5) .908 (23.1) .830 (21.1)
18 18 1.000 - 20 UNEF 1.140 (29.0) .730 (18.5) 1.025 (26.0) .996 (25.3)
20 20 1.125 - 18 UNEF 1.260 (32.0) .870 (22.1) 1.212 (30.8) .996 (25.3)
22 22 1.250 - 18 UNEF 1.390 (35.3) .978 (24.8) 1.343 (34.1) .996 (25.3)
24 24 1.375 - 18 UNEF 1.520 (38.6) 1.090 (27.7) 1.450 (36.8) .996 (25.3)
28 28 1.625 - 18 UNEF 1.760 (44.7) 1.250 (31.8) 1.671 (42.4) 1.076 (27.3)
32 32 1.875 - 16 UN 2.010 (51.1) 1.520 (38.6) 1.956 (49.7) 1.076 (27.3)
36 36 2.125 - 16 UN 2.260 (57.4) 1.756 (44.6) 2.164 (55.0) 1.076 (27.3)
40 40 2.375 - 16 UN 2.510 (63.8) 1.880 (47.8) 2.500 (63.5) 1.222 (31.0)
CONNECTOR DESIGNATOR:
KMIL-DTL-83723 Series II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-83723
E
Mil-Spec Backshells
M83723/35S
Straight Non-Environmental Strain Relief Backshell
TABLE I: Shell Size, Cable Range and Dimensions
Shell
Size
Shell Size (s)
(Ref)
A Thread
Class 2B
B Dia
Max
E
Max
F
Max
Cable Range
Min Max
08 8S .438 - 28 UNEF .585 (14.9) 1.290 (32.8) .843 (21.4) .125 (3.2) .235 (6.0)
10 10S .500 - 28 UNEF .645 (16.4) 1.290 (32.8) .843 (21.4) .125 (3.2) .235 (6.0)
11 10SL .562 - 24 UNEF .730 (18.5) 1.290 (32.8) .906 (23.0) .170 (4.3) .297 (7.5)
13 12 & 12S .625 - 24 UNEF .770 (19.6) 1.290 (32.8) 1.085 (27.6) .170 (4.3) .297 (7.5)
15 14 & 14S .750 - 20 UNEF .910 (23.1) 1.368 (34.7) 1.093 (27.8) .235 (6.0) .422 (10.7)
16 16 .875 - 20 UNEF 1.035 (26.3) 1.587 (40.3) 1.275 (32.4) .295 (7.5) .547 (13.9)
17 16S .875 - 20 UNEF 1.035 (26.3) 1.430 (36.3) 1.187 (30.1) .295 (7.5) .547 (13.9)
18 18 1.000 - 20 UNEF 1.170 (29.7) 1.695 (43.1) 1.475 (37.5) .325 (8.3) .610 (15.5)
20 20 1.125 - 18 UNEF 1.300 (33.0) 1.695 (43.1) 1.500 (38.1) .380 (9.7) .735 (18.7)
22 22 1.250 - 18 UNEF 1.420 (36.1) 1.695 (43.1) 1.710 (43.4) .380 (9.7) .735 (18.7)
24 24 1.375 - 18 UNEF 1.535 (39.0) 1.931 (49.0) 1.719 (43.7) .500 (12.7) .922 (23.4)
28 28 1.625 - 18 UNEF 1.800 (45.7) 1.931 (49.0) 2.040 (51.8) .500 (12.7) .922 (23.4)
32 32 1.875 - 16 UNEF 2.035 (51.6) 1.869 (47.5) 2.332 (59.2) .705 (17.9) 1.235 (31.4)
36 36 2.125 - 16 UN 2.270 (57.7) 1.869 (47.5) 2.312 (58.7) .725 (18.4) 1.360 (34.5)
40 40 2.375 - 16 UN 2.780 (70.6) 2.875 (73.0) 2.950 (74.9) .911 (23.1) 1.630 (41.4)
APPLICATION
NOTES
1. For complete
dimensions see the
applicable Military
Specication.
2. Metric dimensions
(mm) are in
parentheses.
3. Cable Range is
dened as the
accommodation
range for the wire
bundle or cable.
Dimensions shown
are not intended for
inspection criteria.
Basic
Part Number
M83723/35S -22 A
Shell
Size
Finish
A = Anodize Black
R = Electroless Nickel
CONNECTOR DESIGNATOR:
KMIL-DTL-83723 Series II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-83723
E
M83723/35A
90° Non-Environmental Strain Relief Backshell
Basic
Part Number
M83723/35A -22 A
Shell
Size
Finish
A = Anodize Black
R = Electroless Nickel
APPLICATION
NOTES
1. For complete
dimensions see the
applicable Military
Specication.
2. Metric dimensions
(mm) are in
parentheses.
3. Cable Range is
dened as the
accommodation
range for the wire
bundle or cable.
Dimensions shown
are not intended for
inspection criteria.
TABLE I: Shell Size, Cable Range and Dimensions
Shell
Size A Thread
Class 2B B Dia
Max E
Max F
Max Cable Range
Min Max
08 .438 - 28 UNEF .805 (20.4) 1.187 (30.1) 1.220 (31.0) .102 (2.6) .235 (6.0)
10 .500 - 28 UNEF .890 (22.6) 1.187 (30.1) 1.250 (31.8) .102 (2.6) .235 (6.0)
11 .562 - 24 UNEF .975 (24.8) 1.312 (33.3) 1.280 (32.5) .140 (3.6) .297 (7.5)
13 .625 - 24 UNEF 1.005 (25.5) 1.312 (33.3) 1.280 (32.5) .140 (3.6) .297 (7.5)
12 .625 - 24 UNEF 1.005 (25.5) 1.468 (37.3) 1.280 (32.5) .140 (3.6) .297 (7.5)
15 .750 - 20 UNEF 1.130 (28.7) 1.437 (36.5) 1.405 (35.7) .195 (5.0) .422 (10.7)
14 .750 - 20 UNEF 1.130 (28.7) 1.594 (40.5) 1.405 (35.7) .195 (5.0) .422 (10.7)
17 .875 - 20 UNEF 1.255 (31.9) 1.531 (38.9) 1.529 (38.8) .255 (6.5) .547 (13.9)
16 .875 - 20 UNEF 1.255 (31.9) 1.687 (42.8) 1.529 (38.8) .255 (6.5) .547 (13.9)
18 1.000 - 20 UNEF 1.350 (34.3) 1.765 (44.8) 1.593 (40.5) .285 (7.2) .610 (15.5)
20 1.125 - 18 UNEF 1.475 37.5) 2.000 (50.8) 1.655 (42.0) .350 (8.9) .735 (18.7)
22 1.250 - 18 UNEF 1.600 (40.6) 2.000 (50.8) 1.718 (43.6) .350 (8.9) .735 (18.7)
24 1.375 - 18 UNEF 1.725 (43.8) 2.265 (57.5) 1.894 (48.1) .468 (11.9) .922 (23.4)
28 1.625 - 18 UNEF 1.975 (50.2) 2.265 (57.5) 1.973 (50.1) .468 (11.9) .922 (23.4)
32 1.875 - 16 UN 2.225 56.5) 2.578 (65.5) 2.187 (55.5) .664 (16.9) 1.235 (31.4)
36 2.125 - 16 UN 2.475 (62.9) 2.815 (71.5) 2.405 (61.1) .694 (17.6) 1.360 (34.5)
40 2.375 - 16 UN 2.750 (69.9) 5.800 (147.3) 5.100 (129.5) .911 (23.1) 1.630 (41.4)
CONNECTOR DESIGNATOR:
KMIL-DTL-83723 Series II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-83723
E
Mil-Spec Backshells Rev. 8.29.14
M83723/35N
Non-Self-Locking E-Nut
A Thread
BF
E
G
Grounding Screws (2)
(Typical)
CONNECTOR DESIGNATOR:
KMIL-DTL-83723 Series II
Basic Part
Number
M83723/35N -22 A
Dash No.
Finish
A = Black Anodize
R = Electroless Nickel
TABLE I: Dash Number, Shell Size, Thread and Dimensions
Dash
No.
Shell Size
Ref.
A Thread
Class 2B
Ø B
Max
E
Max
F
Max
G
Max
08 8S .438 - 28 UNEF .59 (15.0) .780 (19.8) .257 (6.5) .900 (22.9)
10 10S .500 - 28 UNEF .65 (16.5) .780 (19.8) .310 (7.9) .900 (22.9)
11 10SL .562 - 24 UNEF .73 (18.5) .780 (19.8) .390 (9.9) .980 (24.9)
13 12S .625 - 24 UNEF .77 (19.6) .780 (19.8) .415 (10.5) .995 (25.3)
15 14S .750 - 20 UNEF .91 (23.1) .780 (19.8) .497 (12.6) 1.160 29.5)
16 16 .875 - 20 UNEF 1.03 (26.2) .970 (24.6) .616 (15.6) 1.260 (32.0)
17 16S .875 - 20 UNEF 1.03 (26.2) .780 (19.8) .616 (15.6) 1.260 (32.0)
18 18 1.000 - 20 UNEF 1.17 (29.7) 1.050 (26.7) .735 (18.7) 1.455 (37.0)
20 33 1.125 - 18 UNEF 1.30 (33.0) 1.050 (26.7) .875 (22.2) 1.580 (40.1)
22 20 1.250 - 18 UNEF 1.42 (36.1) 1.050 (26.7) .983 (25.0) 1.580 (40.1)
24 22 1.375 - 18 UNEF 1.54 (39.1) .970 (24.6) 1.095 (27.8) 1.890 (48.0)
28 28 1.625 - 18 UNEF 1.80 (45.7) .970 (24.6) 1.255 (31.9) 1.890 (48.0)
32 32 1.875 - 16 UN 2.04 (51.8) .970 (24.6) 1.525 (38.7) 2.215 (56.3)
36 36 2.125 - 16 UN 2.27 (57.7) .970 (24.6) 1.760 (44.7) 2.405 (61.1)
40 40 2.375 - 16 UN 2.78 (70.6) 1.450 (36.8) 2.020 (51.3) 2.781 (70.6)
APPLICATION NOTES
1. For complete
dimensions, see the
applicable Military
Specication.
2. Metric dimensions
(mm) are indicated in
parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-83723
E
Mil-Spec Backshells Rev. 8.29.14
M83723/50
Straight, 45° and 90° Qwik-Ty® Strain Reliefs
Non-Self-Locking
TABLE I: Shell Size, Thread, Cable Entry and Backshell Dimensions
Shell
Size
A Thread
Class 2B
D Dia
Max
E Max
Cable Entry
F
Max
G
Max
H
Max
J
Max
08 .438 - 28 UNEF .620 (15.7) .240 (6.1) 1.060 (26.9) .740 (18.8) .710 (18.0) .880 (22.4)
10 .500 - 28 UNEF .730 (18.5) .295 (7.5) 1.060 (26.9) .740 (18.8) .710 (18.0) .940 (23.9)
11 .562 - 24 UNEF .730 (18.5) .375 (9.5) 1.060 (26.9) .740 (18.8) .710 (18.0) .940 (23.9)
12 .625 - 24 UNEF .860 (21.8) .400 (10.2) 1.120 (28.4) .740 (18.8) .710 (18.0) 1.000 (25.4)
13 .625 - 24 UNEF .860 (21.8) .400 (10.2) 1.120 (28.4) .740 (18.8) .710 (18.0) 1.000 (25.4)
14 .750 - 20 UNEF .980 (24.9) .482 (12.2) 1.300 (33.0) 2.010 (51.1) .710 (18.0) 1.320 (33.5)
15 .750 - 20 UNEF .980 (24.9) .482 (12.2) 1.310 (33.3) 2.020 (51.3) .710 (18.0) 1.320 (33.5)
16 .875 - 20 UNEF 1.110 (28.2) .601 (15.3) 1.300 (33.0) 2.010 (51.1) .710 (18.0) 1.370 (34.8)
17 .875 - 20 UNEF 1.110 (28.2) .601 (15.3) 1.300 (33.0) 2.010 (51.1) .710 (18.0) 1.370 (34.8)
18 1.000 - 20 UNEF 1.220 (31.0) .722 (18.3) 1.360 (34.5) 2.170 (55.1) .730 (18.5) 1.470 (37.3)
20 1.125 - 18 UNEF 1.350 (34.3) .862 (21.9) 1.500 (38.1) 2.250 (57.2) .740 (18.8) 1.510 (38.4)
22 1.250 - 18 UNEF 1.470 (37.3) .970 (24.6) 1.620 (41.1) 2.250 (57.2) .630 (16.0) 1.570 (39.9)
24 1.375 - 18 UNEF 1.590 (40.4) 1.082 (27.5) 1.680 (42.7) 2.330 (59.2) .630 (16.0) 1.640 (41.7)
28 1.625 - 18 UNEF 1.970 (50.0) 1.241 (31.5) 1.710 (43.4) 2.330 (59.2) .630 (16.0) 1.710 (43.4)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Cable entry is dened as the accomodation range for the wire bundle or cable. Dimensions shown are not
intended for inspection criteria.
4. Metric dimensions (mm) are in parentheses.
A Thread
Typ.
D
Typ.
H
MS3367-1
Tie Strap or
Equivalent
(Typical)
E
F
E
J
E
G
Set
Screw
(Typ.)
Basic Part Number
M83723/50R = Straight
M83723/50B = 45°
M83723/50A = 90°
M83723/50 R 22 N
Angular
Function
R = Straight
B = 45°
A = 90°
Finish
A = Black Anodize
N = Electroless
Nickel
Shell
Size
CONNECTOR DESIGNATOR:
KMIL-DTL-83723, Series II
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-83723
E
M83723/59-1, M83723/60-1, MS27292 and MS27294
Threaded Protective Plug and ReceptacleCovers
Gasket
.125 (3.2)
Max Dia.
F
M83723/60-1 RECEPTACLE COVER
M27294 RECEPTACLE COVER (SEE NOTE 3)
M83723/59-1 PLUG COVER
M27292 PLUG COVER (SEE NOTE 3)
Length
.618 (15.7)
Max
E Thread
.125 (3.2)
Max Dia.
Gasket
Length
F
.757
(19.2)
E Thread
APPLICATION NOTES
1. Assembly identied with manufacturer’s name and part
number, space permitting.
2. For complete dimensions, see the applicable Military
Specication.
3. MS27292 and MS27294 have a black anodize nish.
Dash numbers 1, 2 and 7 have a 3.0-inch (76.2) wire rope
attachment. Other dash numbers have a 5-inch (127.0) wire
rope attachent.
4. Metric dimensions (mm) are in parentheses.
TABLE I: Shell Size, Dash Number,
Thread and Dimensions
Shell
Size
M27292
M27294
Dash No.
E
Thread
Class 2A/2B
K Dia
Max
8 7 9/16 - 24 UNEF .776 (19.7)
10 1 11/16 - 24 UNEF .906 (23.0)
12 2 7/8 - 20 UNEF 1.078 (27.4)
14 3 15/16 - 20 UNEF 1.141 (29.0)
16 4 1 1/16 - 18 UNEF 1.266 (32.2)
18 5 1 3/16 - 18 UNEF 1.375 (34.9)
20 8 1 5/16 - 18 UNEF 1.510 (38.4)
22 6 1 7/16 - 18 UNEF 1.625 (41.3)
24 9 1 9/16 - 18 UNEF 1.760 (44.7)
Basic Part Number
M83723/59-1 = Plug Cover
M83723/60-1 = Receptacle Cover
M83723/59-1 10 A C
Shell
Size
Finish
A = Black Anodize
R = Electroless Nickel
W = Cadmium over Electroless Nickel
Attachment Style
C = 5.0” (127.0) Chain
P = 8.0” (203.2) Chain
R = 5.0” (127.0) Rope
T = 8.0” (203.2) Rope
N = No Attachment
Superseded Part Number
Basic Part Number
MS27292 = Plug Cover
MS27294 = Receptacle Cover Dash
Number
MS27292 -1
See Note 3
MATING CONNECTOR
MIL-DTL-83723, Series III Threaded
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-8
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-83723
E
M83723/59-2, M83723/60-2, MS27293 and MS29295
Protective Plug and ReceptacleCovers
Bayonet Coupling
Superseded Part Number
Basic Part Number
MS27293 = Plug Cover
MS27295 = Receptacle Cover Dash
Number
MS27293 -1
See Note 3
Basic Part Number
M83723/59-2 = Plug Cover
M83723/60-2 = Receptacle Cover
M83723/59-2 10 A C
Shell
Size
Finish
A = Black Anodize
R = Electroless Nickel
W = Cadmium over Electroless Nickel
Attachment Style
C = 5.0” (127.0) Chain
P = 8.0” (203.2) Chain
R = 5.0” (127.0) Rope
T = 8.0” (203.2) Rope
N = No Attachment
TABLE I: Shell Size,
Dash Number
and Dimensions
Shell
Size
M27292
M27294
Dash No.
F Dia
Max
8 7 .776 (19.7)
10 1 .906 (23.0)
12 2 1.078 (27.4)
14 3 1.141 (29.0)
16 4 1.266 (32.2)
18 5 1.375 (34.9)
20 8 1.510 (38.4)
22 6 1.625 (41.3)
24 9 1.760 (44.7)
MATING CONNECTOR
MIL-DTL-83723 Bayonet
Gasket
Length
F
.757 (19.2)
Max
.125 (3.2)
Max Dia.
M83723/59-2 PLUG COVER
M27293 PLUG COVER (SEE NOTE 3)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-9
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
MIL-DTL-83723
E
M83723/70
Series III Quick-Disconnect Receptacle Adapter
.010 (0.3) X 45°
B C FD
.320 (8.1) .065 (1.7)
.040 (1.0)
.065 (1.7)
.060 (1.5) .035 (0.9)
.442 (11.2)
.410 (10.4)
.292 (7.4)
.288 (7.3)
.025 (0.6) Min Width
Coupled Indicator Line
Color Coded Blue E Radius
30°
20°
A Thread
APPLICATION NOTES
1. Dimensions are in inches and apply after plating.
2. Metric equivalents are in parentheses and given for information only.
3. Unless otherwise specied, tolerances shall be ±.005 (0.13) for three decimal places,
±.01 (0.25) for two decimal places and ± 1/2° for all angles.
4. Coupling indicator line shall be color coded blue and .025 ± .010 (0.64 ± 0.25) wide.
Basic
Part Number
M83723/70 W 22
Dash No.
Material and Finish
A = Aluminum, Black Anodize
R = Aluminum, Electroless Nickel
G = Corrosion-Resistant Steel Passivate
W = Aluminum, Cadmium Olive Drab over
Electroless Nickel
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
E-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
MIL-DTL-83723
E
TABLE I: Shell Size, Thread, Teeth and Dimensions
Shell
Size
A
Coupling Thread
UNEF-2B
B
Dia C
Dia D
Dia E
Radius F
Dia
8.5625-24 .607 (15.42)
.603 (15.32) .579 (14.71)
.575 (14.61) .689 (17.50)
.685 (17.40) .036 (0.91)
.031 (0.79) .525 (13.34)
10 .6875-24 .732 (18.59)
.728 (18.49) .714 (18.14)
.710 (18.03) .814 (20.68)
.810 (20.57) .036 (0.91)
.031 (0.79) .650 (16.51)
12 .875-20 .918 (23.34)
.915 (23.24) .894 (22.71)
.890 (22.61) 1.001 (25.43)
.997 (25.32) .036 (0.91)
.031 (0.79) .840 (21.34)
14 .9375-20 .982 (24.94)
.978 (24.84) .954 (24.23)
.950 (24.13) 1.064 (27.03)
1.060 (26.92) .036 (0.91)
.031 (0.79) .900 (22.86)
16 1.0625-18 1.107 (28.12)
1.103 (28.02) 1.079 (27.41)
1.075 (27.31) 1.189 (30.20)
1.185 (30.10) .036 (0.91)
.031 (0.79) 1.025 (26.04)
18 1.1875-18 1.232 (31.29)
1.228 (31.19) 1.204 (30.58)
1.200 (30.48) 1.330 (33.78)
1.326 (33.68) .044 (1.12)
.039 (0.99) 1.150 (29.21)
20 1.3125-18 1.357 (34.47)
1.353 (34.37) 1.329 (33.76)
1.325 (33.66) 1.455 (36.96)
1.451 (36.86) .044 (1.12)
.039 (0.99) 1.275 (32.39)
22 1.4375-18 1.482 (37.64)
1.478 (37.54) 1.454 (36.93)
1.450 (36.83) 1.580 (40.13)
1.576 (40.03) .044 (1.12)
.039 (0.99) 1.400 (35.56)
24 1.5625-18 1.607 (40.82)
1.603 (40.72) 1.579 (40.11)
1.575 (40.01) 1.705 (43.31)
1.701 (43.21) .044 (1.12)
.039 (0.99) 1.525 (38.74)
M83723/70
Straight Adapter
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS81511
F
AS81511
Qualied Backshells and Connector Accessories
SECTION F • AS81511 QUALIFIED PRODUCTS • SECTION F
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS81511/13 M81511/13 –– 620JS001 Straight Non-Self-Locking Strain Relief “J”
AS81511 Series I, II, III & IV F-2
AS81511/14 M8151 1/14 A
M81511/14 B –– 390JS012
390JS012 Straight EMI/RFI Environmental Backshell A
Straight EMI/RFI Environmental Backshell B “J”
AS81511 Series I, II, III & IV F-3
AS81511/14 M81511/14 C
M81511/14 D –– 380JS008
380JS008 Str. EMI/RFI Non-Environmental Backshell C
Str. EMI/RFI Non-Environmental Backshell D “J”
AS81511 Series I, II, III & IV F-5
AS81511/17
AS81511/18 M81511/17
M81511/18 –– 660-017
660-018 Protective Plug Cover
Protective Receptacle Cover AS81511 Series I, II, III & IV F-7
AS81511/19 M81511/19 –– 650JS002 Dummy Storage Receptacle AS81511 Series I, II, III & IV F-8
AS81511/20 M81511/20 –– Consult Factory Jam Nut AS81511 Series I, II, III & IV F-9
AS81511/29 M81511/29 –– 660-016 Protective Plug Cover AS81511 Series I, II, III & IV F-7
AS81511/30 M81511/30 –– 650JS001 Dummy Storage Receptacle Bayonet Coupling MIL-DTL-26500 and
MIL-DTL-83723, Series III F-10
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS81511
F
AS81511/13
Straight Non-Self-Locking Strain Relief
A Thread
Cable
Entry
E
F
CONNECTOR DESIGNATOR:
JAS81511 Series I, II, III & IV
TABLE I: Shell Size, Cable Entry and Backshell Dimensions
Shell Size A Thread
Class 2B E
Max F
Max Cable Entry
Min Max
08 .500 - 28 UNEF 1.375 (34.9) .775 (19.7) .062 (1.6) .125 (3.2)
10 .625 - 28 UN 1.375 (34.9) .955 (24.3) .125 (3.2) .250 (6.4)
14 .875 - 28 UN 1.375 (34.9) 1.145 (29.1) .250 (6.4) .500 (12.7)
16 1.000 - 28 UN 1.375 (34.9) 1.210 (30.7) .375 (9.5) .625 (15.9)
18 1.125 - 28 UN 1.375 (34.9) 1.330 (33.8) .500 (12.7) .750 (19.1)
20 1.250 - 28 UN 1.452 (36.9) 1.470 (37.3) .625 (15.9) .875 (22.2)
22 1.375 - 28 UN 1.452 (36.9) 1.580 (40.1) .750 (19.1) 1.000 (25.4)
24 1.500 - 28 UN 1.452 (36.9) 1.720 (43.7) .750 (19.1) 1.125 (28.6)
Basic
Part Number
M81511/13 16 A1
Shell Size
Adapter Connector Class Designator
A1 = Classes E, H, and P
B1 = Classes A, B, C, F, G, and T
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. Cable Entry is dened as the accommodation entry for the wire bundle or cable.
Dimensions are not intended for inspection criteria.
3. For complete dimensions, see the applicable Military Specication.
4. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS81511
F
AS81511/14
Straight EMI/RFI Environmental Backshell A & B
APPLICATION NOTES
1. For complete dimensions see the applicable
Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the
accommodation range for the wire bundle or
cable. Dimensions shown are not intended
for inspection criteria.
4. For functions C and D see page F-5.
Basic
Part Number
M81511/14 -050
Dash Number
(Table I)
TABLE I: Dash Number and Dimensions
Dash
No. Shell
Size Function A Thread
Class 2B Length
Ref. Cable Range
Min Max
001 08 A .500 - 28 UNEF 2.22 (56.4) .062 (1.6) .125 (3.2)
002 08 A .500 - 28 UNEF 2.22 (56.4) .125 (3.2) .250 (6.4)
003 08 B .500 - 28 UNEF 2.72 (69.1) .062 (1.6) .125 (3.2)
004 08 B .500 - 28 UNEF 2.72 (69.1) .125 (3.2) .250 (6.4)
005 08 A .500 - 28 UNEF 2.72 (69.1) .062 (1.6) .125 (3.2)
006 08 A .500 - 28 UNEF 2.72 (69.1) .125 (3.2) .250 (6.4)
007 08 B .500 - 28 UNEF 3.22 (81.8) .062 (1.6) .125 (3.2)
008 08 B .500 - 28 UNEF 3.22 (81.8) .125 (3.2) .250 (6.4)
009 10 A .625 - 28 UN 2.22 (56.4) .125 (3.2) .250 (6.4)
010 10 A .625 - 28 UN 2.22 (56.4) .250 (6.4) .375 (9.5)
011 10 A .625 - 28 UN 2.22 (56.4) .375 (9.5) .500 (12.7)
012 10 B .625 - 28 UN 2.72 (69.1) .125 (3.2) .250 (6.4)
013 10 B .625 - 28 UN 2.72 (69.1) .250 (6.4) .375 (9.5)
014 10 B .625 - 28 UN 2.72 (69.1) .375 (9.5) .500 (12.7)
015 10 A .625 - 28 UN 2.72 (69.1) .125 (3.2) .250 (6.4)
016 10 A .625 - 28 UN 2.72 (69.1) .250 (6.4) .375 (9.5)
017 10 A .625 - 28 UN 2.72 (69.1) .375 (9.5) .500 (12.7)
018 10 B .625 - 28 UN 3.22 (81.8) .125 (3.2) .250 (6.4)
019 10 B .625 - 28 UN 3.22 (81.8) .250 (6.4) .375 (9.5)
020 10 B .625 - 28 UN 3.22 (81.8) .375 (9.5) .500 (12.7)
021 14 A .875 - 28 UN 2.22 (56.4) .250 (6.4) .375 (9.5)
022 14 A .875 - 28 UN 2.22 (56.4) .375 (9.5) .500 (12.7)
023 14 A .875 - 28 UN 2.22 (56.4) .500 (12.7) .625 (15.9)
024 14 B .875 - 28 UN 2.72 (69.1) .250 (6.4) .375 (9.5)
025 14 B .875 - 28 UN 2.72 (69.1) .375 (9.5) .500 (12.7)
026 14 B .875 - 28 UN 2.72 (69.1) .500 (12.7) .625 (15.9)
027 14 A .875 - 28 UN 2.72 (69.1) .250 (6.4) .375 (9.5)
028 14 A .875 - 28 UN 2.72 (69.1) .375 (9.5) .500 (12.7)
029 14 A .875 - 28 UN 2.72 (69.1) .500 (12.7) .625 (15.9)
030 14 B .875 - 28 UN 3.22 (81.8) .250 (6.4) .375 (9.5)
031 14 B .875 - 28 UN 3.22 (81.8) .375 (9.5) .500 (12.7)
032 14 B .875 - 28 UN 3.22 (81.8) .500 (12.7) .625 (15.9)
033 16 A 1.000 - 28 UN 2.22 (56.4) .250 (6.4) .375 (9.5)
034 16 A 1.000 - 28 UN 2.22 (56.4) .375 (9.5) .500 (12.7)
035 16 A 1.000 - 28 UN 2.22 (56.4) .500 (12.7) .625 (15.9)
036 16 B 1.000 - 28 UN 2.72 (69.1) .250 (6.4) .375 (9.5)
037 16 B 1.000 - 28 UN 2.72 (69.1) .375 (9.5) .500 (12.7)
Table I Continued on Page F-4
Function “A” Adapter Assembly
Function “B” Adapter Assembly
CONNECTOR DESIGNATOR:
JAS81511 Series I, II, III & IV
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS81511
F
AS81511/14
Straight EMI/RFI Environmental Backshell A & B
TABLE I: Dash Number and Dimensions (Continued from Page F-3)
Dash
No. Shell
Size Function A Thread
Class 2B C Dia
Max Length
Ref. Cable Range
Min Max
038 16 B 1.000 - 28 UN 1.056 (26.8) 2.72 (69.1) .500 (12.7) .625 (15.9)
039 16 A 1.000 - 28 UN 1.056 (26.8) 2.72 (69.1) .250 (6.4) .375 (9.5)
040 16 A 1.000 - 28 UN 1.056 (26.8) 2.72 (69.1) .375 (9.5) .500 (12.7)
041 16 A 1.000 - 28 UN 1.056 (26.8) 2.72 (69.1) .500 (12.7) .625 (15.9)
042 16 B 1.000 - 28 UN 1.056 (26.8) 3.22 (81.8) .250 (6.4) .375 (9.5)
043 16 B 1.000 - 28 UN 1.056 (26.8) 3.22 (81.8) .375 (9.5) .500 (12.7)
044 16 B 1.000 - 28 UN 1.056 (26.8) 3.22 (81.8) .500 (12.7) .625 (15.9)
045 18 A 1.125 - 28 UN 1.180 (30.0) 2.22 (56.4) .375 (9.5) .500 (12.7)
046 18 A 1.125 - 28 UN 1.180 (30.0) 2.22 (56.4) .500 (12.7) .625 (15.9)
047 18 A 1.125 - 28 UN 1.180 (30.0) 2.22 (56.4) .625 (15.9) .750 (19.1)
048 18 B 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .375 (9.5) .500 (12.7)
049 18 B 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .500 (12.7) .625 (15.9)
050 18 B 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .625 (15.9) .750 (19.1)
051 18 A 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .375 (9.5) .500 (12.7)
052 18 A 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .500 (12.7) .625 (15.9)
053 18 A 1.125 - 28 UN 1.180 (30.0) 2.72 (69.1) .625 (15.9) .750 (19.1)
054 18 B 1.125 - 28 UN 1.180 (30.0) 3.22 (81.8) .375 (9.5) .500 (12.7)
055 18 B 1.125 - 28 UN 1.180 (30.0) 3.22 (81.8) .500 (12.7) .625 (15.9)
056 18 B 1.125 - 28 UN 1.180 (30.0) 3.22 (81.8) .625 (15.9) .750 (19.1)
113 20 A 1.250 - 28 UN 1.305 (33.1) 2.30 (58.4) .500 (12.7) .625 (15.9)
114 20 A 1.250 - 28 UN 1.305 (33.1) 2.30 (58.4) .625 (15.9) .750 (19.1)
115 20 A 1.250 - 28 UN 1.305 (33.1) 2.30 (58.4) .750 (19.1) .875 (22.2)
116 20 B 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .500 (12.7) .625 (15.9)
117 20 B 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .625 (15.9) .750 (19.1)
118 20 B 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .750 (19.1) .875 (22.2)
119 20 A 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .500 (12.7) .625 (15.9)
120 20 A 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .625 (15.9) .750 (19.1)
121 20 A 1.250 - 28 UN 1.305 (33.1) 2.80 (71.1) .750 (19.1) .875 (22.2)
122 20 B 1.250 - 28 UN 1.305 (33.1) 3.30 (83.8) .500 (12.7) .625 (15.9)
123 20 B 1.250 - 28 UN 1.305 (33.1) 3.30 (83.8) .625 (15.9) .750 (19.1)
124 20 B 1.250 - 28 UN 1.305 (33.1) 3.30 (83.8) .750 (19.1) .875 (22.2)
125 22 A 1.375 - 28 UN 1.430 (36.3) 2.30 (58.4) .625 (15.9) .750 (19.1)
126 22 A 1.375 - 28 UN 1.430 (36.3) 2.30 (58.4) .750 (19.1) .875 (22.2)
127 22 A 1.375 - 28 UN 1.430 (36.3) 2.30 (58.4) .875 (22.2) 1.000 (25.4)
128 22 B 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .625 (15.9) .750 (19.1)
129 22 B 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .750 (19.1) .875 (22.2)
130 22 B 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .875 (22.2) 1.000 (25.4)
131 22 A 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .625 (15.9) .750 (19.1)
132 22 A 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .750 (19.1) .875 (22.2)
133 22 A 1.375 - 28 UN 1.430 (36.3) 2.80 (71.1) .875 (22.2) 1.000 (25.4)
134 22 B 1.375 - 28 UN 1.430 (36.3) 3.30 (83.8) .625 (15.9) .750 (19.1)
135 22 B 1.375 - 28 UN 1.430 (36.3) 3.30 (83.8) .750 (19.1) .875 (22.2)
136 22 B 1.375 - 28 UN 1.430 (36.3) 3.30 (83.8) .875 (22.2) 1.000 (25.4)
137 24 A 1.500 - 28 UN 1.555 (39.5) 2.30 (58.4) .750 (19.1) .875 (22.2)
138 24 A 1.500 - 28 UN 1.555 (39.5) 2.30 (58.4) .875 (22.2) 1.000 (25.4)
139 24 A 1.500 - 28 UN 1.555 (39.5) 2.30 (58.4) 1.000 (25.4) 1.125 (28.6)
140 24 B 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) .750 (19.1) .875 (22.2)
141 24 B 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) .875 (22.2) 1.000 (25.4)
142 24 B 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) 1.000 (25.4) 1.125 (28.6)
143 24 A 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) .750 (19.1) .875 (22.2)
144 24 A 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) .875 (22.2) 1.000 (25.4)
145 24 A 1.500 - 28 UN 1.555 (39.5) 2.80 (71.1) 1.000 (25.4) 1.125 (28.6)
146 24 B 1.500 - 28 UN 1.555 (39.5) 3.30 (83.8) .750 (19.1) .875 (22.2)
147 24 B 1.500 - 28 UN 1.555 (39.5) 3.30 (83.8) .875 (22.2) 1.000 (25.4)
148 24 B 1.500 - 28 UN 1.555 (39.5) 3.30 (83.8) 1.000 (25.4) 1.125 (28.6)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
AS81511
F
AS81511/14 Functions C and D
Straight EMI/RFI Non-Environmental Backshell
Basic
Part Number
M81511/14 100
Dash Number
(Table I)
Function "C" Adapter Assembly Function "D" Adapter Assembly
Table I Continued on Next Column (Right) Table I Continued on Page F-6
CONNECTOR DESIGNATOR:
JAS81511 Series I, II, III & IV
TABLE I: Dash Number and Dimensions
Dash
No. Shell
Size Function A Thread
Class 2B C Dia
Max Length
Ref. Cable Range
Min Max
057 08 C .500 - 28 UNEF .555 (14.1) 1.71 (43.4) 062 (1.6) .125 (3.2)
058 08 C .500 - 28 UNEF .555 (14.1) 1.71 (43.4) .125 (3.2) .250 (6.4)
059 08 D .500 - 28 UNEF .555 (14.1) 2.47 (62.7) .062 (1.6) .125 (3.2)
060 08 D .500 - 28 UNEF .555 (14.1) 2.47 (62.7) .125 (3.2) .250 (6.4)
061 08 C .500 - 28 UNEF .555 (14.1) 2.21 (56.1) .062 (1.6) .125 (3.2)
062 08 C .500 - 28 UNEF .555 (14.1) 2.21 (56.1) .125 (3.2) .250 (6.4)
063 08 D .500 - 28 UNEF .555 (14.1) 2.97 (75.4) .062 (1.6) .125 (3.2)
064 08 D .500 - 28 UNEF .555 (14.1) 2.97 (75.4) .125 (3.2) .250 (6.4)
065 10 C .625 - 28 UN .680 (17.3) 1.71 (43.4) .125 (3.2) .250 (6.4)
066 10 C .625 - 28 UN .680 (17.3) 1.71 (43.4) .250 (6.4) .375 (9.5)
067 10 C .625 - 28 UN .680 (17.3) 1.71 (43.4) .375 (9.5) .500 (12.7)
068 10 D .625 - 28 UN .680 (17.3) 2.47 (62.7) .125 (3.2) .250 (6.4)
069 10 D .625 - 28 UN .680 (17.3) 2.47 (62.7) .250 (6.4) .375 (9.5)
070 10 D .625 - 28 UN .680 (17.3) 2.47 (62.7) .375 (9.5) .500 (12.7)
071 10 C .625 - 28 UN .680 (17.3) 2.21 (56.1) .125 (3.2) .250 (6.4)
072 10 C .625 - 28 UN .680 (17.3) 2.21 (56.1) .250 (6.4) .375 (9.5)
073 10 C .625 - 28 UN .680 (17.3) 2.21 (56.1) .375 (9.5) .500 (12.7)
074 10 D .625 - 28 UN .680 (17.3) 2.97 (75.4) .125 (3.2) .250 (6.4)
075 10 D .625 - 28 UN .680 (17.3) 2.97 (75.4) .250 (6.4) .375 (9.5)
076 10 D .625 - 28 UN .680 (17.3) 2.97 (75.4) .375 (9.5) .500 (12.7)
077 14 C .875 - 28 UN .930 (23.6) 1.71 (43.4) .250 (6.4) .375 (9.5)
078 14 C .875 - 28 UN .930 (23.6) 1.71 (43.4) .375 (9.5) .500 (12.7)
079 14 C .875 - 28 UN .930 (23.6) 1.71 (43.4) .500 (12.7) .625 (15.9)
080 14 D .875 - 28 UN .930 (23.6) 2.47 (62.7) .250 (6.4) .375 (9.5)
081 14 D .875 - 28 UN .930 (23.6) 2.47 (62.7) .375 (9.5) .500 (12.7)
082 14 D .875 - 28 UN .930 (23.6) 2.47 (62.7) .500 (12.7) .625 (15.9)
083 14 C .875 - 28 UN .930 (23.6) 2.21 (56.1) .250 (6.4) .375 (9.5)
084 14 C .875 - 28 UN .930 (23.6) 2.21 (56.1) .375 (9.5) .500 (12.7)
085 14 C .875 - 28 UN .930 (23.6) 2.21 (56.1) .500 (12.7) .625 (15.9)
086 14 D .875 - 28 UN .930 (23.6) 2.97 (75.4) .250 (6.4) .375 (9.5)
087 14 D .875 - 28 UN .930 (23.6) 2.97 (75.4) .375 (9.5) .500 (12.7)
088 14 D .875 - 28 UN .930 (23.6) 2.97 (75.4) .500 (12.7) .625 (15.9)
TABLE I: Dash Number and Dimensions (Continued)
Dash
No. Shell
Size Function A Thread
Class 2B C Dia
Max Length
Ref. Cable Range
Min Max
089 16 C 1.000 - 28 UN 1.056 (26.8) 1.71 (43.4) .250 (6.4) .375 (9.5)
090 16 C 1.000 - 28 UN 1.056 (26.8) 1.71 (43.4) .375 (9.5) .500 (12.7)
091 16 C 1.000 - 28 UN 1.056 (26.8) 1.71 (43.4) .500 (12.7) .625 (15.9)
092 16 D 1.000 - 28 UN 1.056 (26.8) 2.47 (62.7) .250 (6.4) .375 (9.5)
093 16 D 1.000 - 28 UN 1.056 (26.8) 2.47 (62.7) .375 (9.5) .500 (12.7)
094 16 D 1.000 - 28 UN 1.056 (26.8) 2.47 (62.7) .500 (12.7) .625 (15.9)
095 16 C 1.000 - 28 UN 1.056 (26.8) 2.21 (56.1) .250 (6.4) .375 (9.5)
096 16 C 1.000 - 28 UN 1.056 (26.8) 2.21 (56.1) .375 (9.5) .500 (12.7)
097 16 C 1.000 - 28 UN 1.056 (26.8) 2.21 (56.1) .500 (12.7) .625 (15.9)
098 16 D 1.000 - 28 UN 1.056 (26.8) 2.97 (75.4) .250 (6.4) .375 (9.5)
099 16 D 1.000 - 28 UN 1.056 (26.8) 2.97 (75.4) .375 (9.5) .500 (12.7)
100 16 D 1.000 - 28 UN 1.056 (26.8) 2.97 (75.4) .500 (12.7) .625 (15.9)
101 18 C 1.125 - 28 UN 1.180 (30.0) 1.71 (43.4) .375 (9.5) .500 (12.7)
102 18 C 1.125 - 28 UN 1.180 (30.0) 1.71 (43.4) .500 (12.7) .625 (15.9)
103 18 C 1.125 - 28 UN 1.180 (30.0) 1.71 (43.4) .625 (15.9) .750 (19.1)
104 18 D 1.125 - 28 UN 1.180 (30.0) 2.47 (62.7) .375 (9.5) .500 (12.7)
105 18 D 1.125 - 28 UN 1.180 (30.0) 2.47 (62.7) .500 (12.7) .625 (15.9)
106 18 D 1.125 - 28 UN 1.180 (30.0) 2.47 (62.7) .625 (15.9) .750 (19.1)
107 18 C 1.125 - 28 UN 1.180 (30.0) 2.21 (56.1) .375 (9.5) .500 (12.7)
108 18 C 1.125 - 28 UN 1.180 (30.0) 2.21 (56.1) .500 (12.7) .625 (15.9)
109 18 C 1.125 - 28 UN 1.180 (30.0) 2.21 (56.1) .625 (15.9) .750 (19.1)
110 18 D 1.125 - 28 UN 1.180 (30.0) 2.97 (75.4) .375 (9.5) .500 (12.7)
111 18 D 1.125 - 28 UN 1.180 (30.0) 2.97 (75.4) .500 (12.7) .625 (15.9)
112 18 D 1.125 - 28 UN 1.180 (30.0) 2.97 (75.4) .625 (15.9) .750 (19.1)
149 20 C 1.250 - 28 UN 1.305 (33.1) 1.78 (45.2) .500 (12.7) .625 (15.9)
150 20 C 1.250 - 28 UN 1.305 (33.1) 1.78 (45.2) .625 (15.9) .750 (19.1)
151 20 C 1.250 - 28 UN 1.305 (33.1) 1.78 (45.2) .750 (19.1) .875 (22.2)
152 20 D 1.250 - 28 UN 1.305 (33.1) 2.55 (64.8) .500 (12.7) .625 (15.9)
153 20 D 1.250 - 28 UN 1.305 (33.1) 2.55 (64.8) .625 (15.9) .750 (19.1)
154 20 D 1.250 - 28 UN 1.305 (33.1) 2.55 (64.8) .750 (19.1) .875 (22.2)
155 20 C 1.250 - 28 UN 1.305 (33.1) 2.28 (57.9) .500 (12.7) .625 (15.9)
156 20 C 1.250 - 28 UN 1.305 (33.1) 2.28 (57.9) .625 (15.9) .750 (19.1)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS81511
F
AS81511/14 Functions C and D
Straight EMI/RFI Non-Environmental Backshell
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. Metric dimensions (mm) are in parentheses.
3. Cable Range is dened as the accommodation range for the wire bundle or cable.
Dimensions shown are not intended for inspection criteria.
4. For functions A and B see page F-3.
TABLE I: Dash Number and Dimensions (Continued from Page F-5)
Dash
No. Shell
Size Function A Thread
Class 2B C Dia
Max Length
Ref. Cable Range
Min Max
157 20 C 1.250 - 28 UN 1.305 (33.1) 2.28 (57.9) .750 (19.1) .875 (22.2)
158 20 D 1.250 - 28 UN 1.305 (33.1) 3.05 (77.5) .500 (12.7) .625 (15.9)
159 20 D 1.250 - 28 UN 1.305 (33.1) 3.05 (77.5) .625 (15.9) .750 (19.1)
160 20 D 1.250 - 28 UN 1.305 (33.1) 3.05 (77.5) .750 (19.1) .875 (22.2)
161 22 C 1.375 - 28 UN 1.430 (36.3) 1.78 (45.2) .625 (15.9) .750 (19.1)
162 22 C 1.375 - 28 UN 1.430 (36.3) 1.78 (45.2) .750 (19.1) .875 (22.2)
163 22 C 1.375 - 28 UN 1.430 (36.3) 1.78 (45.2) .875 (22.2) 1.000 (25.4)
164 22 D 1.375 - 28 UN 1.430 (36.3) 2.55 (64.8) .625 (15.9) .750 (19.1)
165 22 D 1.375 - 28 UN 1.430 (36.3) 2.55 (64.8) .750 (19.1) .875 (22.2)
166 22 D 1.375 - 28 UN 1.430 (36.3) 2.55 (64.8) .875 (22.2) 1.000 (25.4)
167 22 C 1.375 - 28 UN 1.430 (36.3) 2.28 (57.9) .625 (15.9) .750 (19.1)
168 22 C 1.375 - 28 UN 1.430 (36.3) 2.28 (57.9) .750 (19.1) .875 (22.2)
169 22 C 1.375 - 28 UN 1.430 (36.3) 2.28 (57.9) .875 (22.2) 1.000 (25.4)
170 22 D 1.375 - 28 UN 1.430 (36.3) 3.05 (77.5) .625 (15.9) .750 (19.1)
171 22 D 1.375 - 28 UN 1.430 (36.3) 3.05 (77.5) .750 (19.1) .875 (22.2)
172 22 D 1.375 - 28 UN 1.430 (36.3) 3.05 (77.5) .875 (22.2) 1.000 (25.4)
173 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) .750 (19.1) .875 (22.2)
174 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) .875 (22.2) 1.000 (25.4)
175 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) 1.000 (25.4) 1.125 (28.6)
176 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) .750 (19.1) .875 (22.2)
177 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) .875 (22.2) 1.000 (25.4)
178 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) 1.000 (25.4) 1.125 (28.6)
179 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) .750 (19.1) .875 (22.2)
180 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) .875 (22.2) 1.000 (25.4)
181 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) 1.000 (25.4) 1.125 (28.6)
182 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) .750 (19.1) .875 (22.2)
183 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) .875 (22.2) 1.000 (25.4)
184 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) 1.000 (25.4) 1.125 (28.6)
171 22 D 1.375 - 28 UN 1.430 (36.3) 3.05 (77.5) .750 (19.1) .875 (22.2)
172 22 D 1.375 - 28 UN 1.430 (36.3) 3.05 (77.5) .875 (22.2) 1.000 (25.4)
173 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) .750 (19.1) .875 (22.2)
174 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) .875 (22.2) 1.000 (25.4)
175 24 C 1.500 - 28 UN 1.555 (39.5) 1.78 (45.2) 1.000 (25.4) 1.125 (28.6)
176 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) .750 (19.1) .875 (22.2)
177 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) .875 (22.2) 1.000 (25.4)
178 24 D 1.500 - 28 UN 1.555 (39.5) 2.55 (64.8) 1.000 (25.4) 1.125 (28.6)
179 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) .750 (19.1) .875 (22.2)
180 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) .875 (22.2) 1.000 (25.4)
181 24 C 1.500 - 28 UN 1.555 (39.5) 2.28 (57.9) 1.000 (25.4) 1.125 (28.6)
182 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) .750 (19.1) .875 (22.2)
183 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) .875 (22.2) 1.000 (25.4)
184 24 D 1.500 - 28 UN 1.555 (39.5) 3.05 (77.5) 1.000 (25.4) 1.125 (28.6)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-7
AS81511
F
Mil-Spec Backshells© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Rev. 8.29.14
AS81511/17, AS81511/18 and AS81511/29
Protective Plug and ReceptacleCovers
Basic Part Number
M81511/17 = Plug Cover Series 2
M81511/18 = Receptacle Cover Series 1and 2
M81511/29 = Plug Cover Series 1
M81511/17 -16
Shell
Size
* Not Applicable for M81511/17 or M81511/18
TABLE I: Shell Size, Attachment and Dimensions
Shell
Size
F Dia
Max
G Dia
+.000 (0.0) -.006 (0.2)
H Max
M81511/29 M81511/17
J
± One Link
K Dia
Max
08 .845 (21.5) .553 (14.0) 1.125 (28.6) .985 (25.0) 3.0 (76.2) .844 (21.4)
10 .970 (24.6) .678 (17.2) 1.125 (28.6) .985 (25.0) 3.0 (76.2) .969 (24.6)
14 1.220 (31.0) .928 (23.6) 1.125 (28.6) .985 (25.0) 3.5 (88.9) 1.219 (31.0)
16 1.345 (34.2) 1.054 (26.8) 1.125 (28.6) .985 (25.0) 3.5 (88.9) 1.345 (34.2)
18 1.470 (37.3) 1.178 (29.9) 1.125 (28.6) .985 (25.0) 3.5 (88.9) 1.469 (37.3)
20* 1.595 (40.5) 1.303 (33.1) 1.125 (28.6) – 3.5 (88.9) 1.594 (40.5)
22* 1.720 (43.7) 1.428 (36.3) 1.125 (28.6) – 3.5 (88.9) 1.719 (43.7)
24* 1.845 (46.9) 1.553 (39.4) 1.125 (28.6) – 3.5 (88.9) 1.844 (46.8)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
M81511/18 Receptacle Cover
Series 1 and 2
FG
Gasket
H
K
Gasket
M81511/29 Plug Cover - Series 1
M81511/17 Plug Cover - Series 2
Dia
.161/156
(4.1/4.0)
.885 (22.5)
Max
Dia
.161/156
(4.1/4.0)
J
J
MATING CONNECTOR
AS81511
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-8
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS81511
F
AS81511/19
Dummy Stowage Receptacle
Bayonet Coupling
F
G
H
JK
EO-Ring
MATING CONNECTOR
AS81511 Series 2 Basic
Part No.
M81511/19 -14 1
Shell Size
Finish:
1 = Cadmium Olive Drab
2 = Dull Chromium over Nickel
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell
Size Ø E F Sq. G Sq. H J K
±.003 (.1) ±.008 (.2) ±.005 (.1) ±.005 (0.1) ±.010 (.3) ±.005 (.1)
08 .550 (14.0) .812 (20.6) .594 (15.1) .121 (3.1) .645 (16.4) .070 (1.8)
10 .675 (17.1) .937 (23.8) .719 (18.3) .121 (3.1) .645 (16.4) .070 (1.8)
14 .925 (23.5) 1.125 (28.6) .906 (23.0) .121 (3.1) .645 (16.4) .070 (1.8)
16 1.051 (26.7) 1.250 (31.8) .969 (24.6) .121 (3.1) .645 (16.4) .070 (1.8)
18 1.175 (29.8) 1.343 (34.1) 1.062 (27.0) .121 (3.1) .645 (16.4) .070 (1.8)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
F-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
AS81511
F
Mil-Spec Backshells Rev. 8.29.14
AS81511/30
Dummy Stowage Receptacle
Bayonet Coupling
F
G
H
JK
E
O-Ring
MATING CONNECTOR
AS81511 Series 1
Basic
Part No.
M81511/30 -14 1
Shell Size
Finish:
1 = Cadmium Olive Drab
2 = Dull Chromium over Nickel
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell
Size
Ø E F Sq. G Sq. H J K
±.003 (.1) ±.008 (.2) ±.005 (.1) ±.005 (0.1) ±.010 (.3) ±.005 (.1)
08 .550 (14.0) .812 (20.6) .594 (15.1) .121 (3.1) .645 (16.4) .070 (1.8)
10 .675 (17.1) .937 (23.8) .719 (18.3) .121 (3.1) .645 (16.4) .070 (1.8)
14 .925 (23.5) 1.125 (28.6) .906 (23.0) .121 (3.1) .645 (16.4) .070 (1.8)
16 1.051 (26.7) 1.250 (31.8) .969 (24.6) .121 (3.1) .645 (16.4) .070 (1.8)
18 1.175 (29.8) 1.343 (34.1) 1.062 (27.0) .121 (3.1) .645 (16.4) .070 (1.8)
20 1.300 (33.0) 1.467 (37.3) 1.156 (29.4) .121 (3.1) .645 (16.4) .070 (1.8)
22 1.425 (36.2) 1.562 (39.7) 1.250 (31.8) .121 (3.1) .645 (16.4) .070 (1.8)
24 1.550 (39.4) 1.703 (43.3) 1.375 (34.9) .148 (3.8) .645 (16.4) .070 (1.8)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-1
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Rev 8-19-14 Printed in U.S.A.
Miscellaneous Qualied Backshells
and Connector Accessories
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
AS25042
AS25043
MS25042
MS25043
MS25042
MS25043
660-004
660-005
Threaded Protective Plug Cover
Threaded Protective Receptacle Cover AS50151 G-2
MS17349
MS17350
MS17349
MS17350 –– 660-007
660-006
Threaded Protective Receptacle Cover
Threaded Protective Plug Cover MIL-DTL-22992 G-3
MS27291 MS27291 –– 620ES050 Straight Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-4
MIL-DTL-26500 MS27558 –– G2221-A 90° Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-5
MIL-DTL-26500 MS27559 –– G2221-B 90° Non-Self-Locking Strain Relief “E”
MIL-DTL-26500 G-6
–– MS27741 –– 410-003 TAG® Ring for Reliable Terminations –– G-7
AS50151 MS3105 –– 650BS001 Dummy Storage Receptacle, Threaded Coupling AS50151 G-8
–– MS3115 –– 650DS001 Dummy Storage Receptacle, Bayonet Coupling MIL-DTL-26482 G-9
–– MS3180
MS3181 –– 660-008
660-009
Protective Plug Cover, Bayonet Coupling
Protectiove Receptacle Cover, Bayonet Coupling MIL-DTL-26482 G-10
–– MS27512 MS3186 Consult Factory Jam Nut with Safety Wire Holes
AS50151; MIL-DTL-26482;
MIL-DTL-26500;
MIL-DTL-83723 Series I;
MIL-DTL-83723, Series III
MIL-DTL-38999 Series I;
MIL-DTL38999 Series II;
MIL-DTL-28840;
MIL-DTL-27599
G-11
–– M29504/04 –– Consult Factory Fiber Optic Pin Terminus, Size 16 MIL-DTL-29504 G-13
–– M29504/05 –– Consult Factory Fiber Optic Socket Terminus, Size 16 MIL-DTL-29504 G-14
MIL-DTL-83513/05 M83513/05 –– Consult Factory Micro-D Jackscrew Kits MIL-DTL-83513/05 G-15
MIL-DTL-83538/9 M83538/9S –– Consult Factory Straight Adapter and Extender MIL-DTL-83538/4 G-16
MIL-S-81824/1 M81824/1 –– 070-001 In-Line Splice, Insulated and Environmental –– G-17
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
AS25042 and AS25043
Protective Plug and ReceptacleCovers
E Thread
F
G
KK
E Thread
Attachment
L Dia Attachment
M Dia
JGasket
H
revoC elcatpeceR 34052SMrevoC gulP 24052SM
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
Basic Part Number
MS25042 = Plug Cover
MS25043 = Receptacle Cover
MS25042 -20 D
Shell Size
(Table I)
Finish
D = Cadmium, O.D.
DA = Black Anodize
TABLE I: Shell Size, Thread, Attachment and Dimensions
Shell
Size E
Thread F Dia
Max G
Max H
Max J
Max K Attachment
Length (Inches) L Dia
Min M Dia
Min
8 1/2 - 28 UNEF .562 (14.3) .656 (16.7) .688 (17.5) .469 (11.9) 4.00 (101.6) .151 (3.8) .135 (3.4)
10 5/8 - 24 UNEF .687 (17.4) .656 (16.7) .815 (20.7) .469 (11.9) 4.00 (101.6) .151 (3.8) .135 (3.4)
12 3/4 - 20 UNEF .812 (20.6) .844 (21.4) 1.000 (25.4) .469 (11.9) 4.50 (114.3) .151 (3.8) .135 (3.4)
14 7/8 - 20 UNEF .937 (23.8) .844 (21.4) 1.125 (28.6) .469 (11.9) 4.50 (114.3) .151 (3.8) .135 (3.4)
16 1 - 20 UNEF 1.062 (27.0) .844 (21.4) 1.188 (30.2) .469 (11.9) 4.50 (114.3) .151 (3.8) .135 (3.4)
18 1 1/8 - 18 UNEF 1.187 (30.1) .844 (21.4) 1.344 (34.1) .469 (11.9) 4.50 (114.3) .151 (3.8) .135 (3.4)
20 1 1/4 - 18 UNEF 1.312 (33.3) .844 (21.4) 1.469 (37.3) .469 (11.9) 5.00 (127.0) .182 (4.6) .135 (3.4)
22 1 3/8 - 18 UNEF 1.437 (36.5) .844 (21.4) 1.594 (40.5) .469 (11.9) 5.00 (127.0) .182 (4.6) .135 (3.4)
24 1 1/2 - 18 UNEF 1.562 (39.7) .844 (21.4) 1.719 (43.7) .469 (11.9) 5.50 (139.7) .182 (4.6) .166 (4.2)
28 1 3/4 - 18 UNS 1.812 (46.0) .844 (21.4) 1.969 (50.0) .531 (13.5) 7.75 (196.9) .182 (4.6) .166 (4.2)
32 2 - 18 UNS 2.062 (52.4) .844 (21.4) 2.219 (56.4) .531 (13.5) 7.75 (196.9) .213 (5.4) .182 (4.6)
36 2 1/4 - 16 UN 2.312 (58.7) .844 (21.4) 2.469 (62.7) .531 (13.5) 7.75 (196.9) .213 (5.4) .182 (4.6)
40 2 1/2 - 16 UN 2.562 (65.1) .844 (21.4) 2.719 (69.1) .531 (13.5) 7.75 (196.9) .213 (5.4) .182 (4.6)
44 2 3/4 - 16 UN 2.812 (71.4) .844 (21.4) 2.969 (75.4) .531 (13.5) 7.75 (196.9) .213 (5.4) .182 (4.6)
48 3 - 16 UN 3.062 (77.8) .844 (21.4) 3.188 (81.0) .531 (13.5) 7.75 (196.9) .213 (5.4) .182 (4.6)
MATING CONNECTOR
AS50151
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
MS17349 and MS17350
Protective Receptacle and Plug Covers
H
J
G
Attachment
(Type B)
M Dia
Gasket
E Thread
1.500
(38.1)
Max
J
Attachment
M Dia
E Thread
MIL-C-22992
L
MS17349
Attachment Type A
Basic Part Number
MS17349 = Receptacle Cover
MS17350 = Plug Cover
MS17349 C 28 A
Dash No.
(Table I)
Finish
C = Conductive
N = Non-Condictive
Attachment Type
A = MS17349 Only
TABLE I: Dash Number, Thread, Attachment and Dimensions
Dash
No.
E
Thread
G
Max
H
Max
J Chain
Length (Inches)
L
Min
M Dia
Min
12 .8750-0.1P-0.2L-DS 1.094 (27.8) .765 (19.4) 5.00 (127.0) 1.016 (25.8) .150 (3.8)
14 1.0000-0.1P-0.2L-DS 1.219 (31.0) .765 (19.4) 5.00 (127.0) 1.141 (29.0) .150 (3.8)
16 1.1250-0.1P-0.2L-DS 1.344 (34.1) .980 (24.9) 5.00 (127.0) 1.266 (32.2) .150 (3.8)
18 1.2500-0.1P-0.2L-DS 1.469 (37.3) .980 (24.9) 5.00 (127.0) 1.391 (35.3) .177 (4.5)
20 1.3750-0.1P-0.2L-DS 1.562 (39.7) .980 (24.9) 5.00 (127.0) 1.516 (38.5) .177 (4.5)
22 1.5000-0.1P-0.2L-DS 1.688 (42.9) .980 (24.9) 6.00 (152.4) 1.641 (41.7) .177 (4.5)
24 1.7500-0.1P-0.2L-DS 1.938 (49.2) .980 (24.9) 6.00 (152.4) 1.891 (48.0) .177 (4.5)
28 2.0000-0.1P-0.2L-DS 2.219 (56.4) .980 (24.9) 6.00 (152.4) 2.141 (54.4) .177 (4.5)
32 2.2500-0.1P-0.2L-DS 2.469 (62.7) .980 (24.9) 6.00 (152.4) 2.391 (60.7) .199 (5.1)
36 2.5000-0.1P-0.2L-DS 2.719 (69.1) .980 (24.9) 6.00 (152.4) 2.641 (67.1) .199 (5.1)
40 2.7500-0.1P-0.2L-DS 2.969 (75.4) .980 (24.9) 6.00 (152.4) 2.891 (73.4) .199 (5.1)
44 3.0000-0.1P-0.2L-DS 3.219 (81.8) .980 (24.9) 6.00 (152.4) 3.141 (79.8) .199 (5.1)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
MATING CONNECTOR
MIL-DTL-22992
MS17349 Receptacle Cover MS17350 Plug Cover
Rev. 04.04.18
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
MS27291
Straight Non-Self-Locking Strain Relief
Basic
Part Number
MS27291 -401
Dash
Number
CONNECTOR DESIGNATOR:
EMIL-DTL-26500
TABLE I: Dash Number, Shell Size, Thread and Dimensions
Dash No. For Use with
Class Connectors Shell Size
Ref. A Thread
Class 2B C
Max EF
Max Ø G
R and F G ±.015 (.4) ±.005 (.1)
1 101 10 .562 - 24 UNEF .731 (18.6) .935 (23.7) .914 (23.2) .270 (6.9)
2 201 12 .750 - 20 UNEF .919 (23.3) .935 (23.7) 1.026 (26.1) .400 (10.2)
3 301 14 .812 - 20 UNEF .981 (24.9) 1.170 (29.7) 1.090 (27.7) .460 (11.7)
4 401 16 .938 - 20 UNEF 1.106 (28.1) 1.170 (29.7) 1.250 (31.8) .610 (15.5)
5 501 18 1.062 - 18 UNEF 1.231 (31.3) 1.170 (29.7) 1.358 (34.5) .690 (17.5)
6 601 22 1.312 - 18 UNEF 1.481 (37.6) 1.170 (29.7) 1.604 (40.7) .940 (23.9)
13 701 8 .438 - 28 UNEF .606 (15.4) .935 (23.7) .789 (20.0) .186 (4.7)
14 801 20 1.188 - 18 UNEF 1.356 (34.4) 1.170 (29.7) 1.481 (37.6) .816 (20.7)
15 901 24 1.438 - 18 UNEF 1.606 (40.8) 1.170 (29.7) 1.729 (43.9) 1.066 (27.1)
APPLICATION NOTES
1. Finish: Class R and F–anodize, Class G, Chrome Plated
2. Assembly to be identied with manufacturer’s name and
part number, space permitting.
3. For complete dimensions, see the applicable Military
Specication.
4. Metric dimensions (mm) are in parentheses.
A Thread
C
E
F
G
G
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
MS27558
90° Non-Self-Locking Strain Relief
A Thread
C
E
F
G
H
Set Screw Wire Holes
(3 Equally Spaced)
Basic
Part Number
MS27558 -3
Dash
Number
CONNECTOR DESIGNATOR:
EMIL-DTL-26500
TABLE I: Dash Number, Shell Size, Thread and Dimensions
Dash
No.
Shell Size
Ref.
A Thread
Class 2B
C
Max
E
Max
F
Max
G
Max
H
Dia
1* 8 .437 - 28 UNEF .672 (17.1) 1.200 (30.5) .602 (15.3) .892 (22.7) .240 (6.1)
2 10 .562 - 24 UNEF .797 (20.2) 1.320 (33.5) .650 (16.5) 1.072 (27.2) .365 (9.3)
3 12 .750 - 20 UNEF 1.016 (25.8) 1.320 (33.5) .740 (18.8) 1.072 (27.2) .365 (9.3)
4 14 .812 - 20 UNEF 1.110 (28.2) 1.487 (37.8) .775 (19.7) 1.108 (28.1) .515 (13.1)
5 16 .938 - 20 UNEF 1.234 (31.3) 1.470 (37.3) .830 (21.1) 1.108 (28.1) .515 (13.1)
6 18 1.062 - 18 UNEF 1.360 (34.5) 1.588 (40.3) .897 (22.8) 1.233 (31.3) .640 (16.3)
7 20 1.188 - 18 UNEF 1.485 (37.7) 1.759 (44.7) .955 (24.3) 1.477 (37.5) .775 (19.7)
8 22 1.312 - 18 UNEF 1.610 (40.9) 1.759 (44.7) 1.015 (25.8) 1.477 (37.5) .775 (19.7)
9 24 1.438 - 18 UNEF 1.735 (44.1) 2.027 (51.5) 1.077 (27.4) 1.727 (43.9) 1.060 (26.9)
* Consult Factory
APPLICATION NOTES
1. Finish: Anodize.
2. Assembly to be identied with manufacturer’s name and
part number, space permitting.
3. For complete dimensions, see the applicable Military
Specication.
4. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
MS27559
90° Non-Self-Locking Strain Relief
Basic
Part Number
MS27559 -4
Dash
Number
CONNECTOR DESIGNATOR:
EMIL-DTL-26500
TABLE I: Dash Number, Shell Size, Thread and Dimensions
Dash
No. Shell Size
Ref. A Thread
Class 2B C
Max E
Max F
Max G
Max H
Dia
1 8 .437 - 28 UNEF .672 (17.1) 1.173 (29.8) .602 (15.3) .892 (22.7) .201 (5.1)
2 10 .562 - 24 UNEF .797 (20.2) 1.293 (32.8) .650 (16.5) 1.072 (27.2) .320 (8.1)
3 12 .750 - 20 UNEF 1.016 (25.8) 1.293 (32.8) .740 (18.8) 1.072 (27.2) .320 (8.1)
4 14 .812 - 20 UNEF 1.110 (28.2) 1.460 (37.1) .775 (19.7) 1.108 (28.1) .452 (11.5)
5 16 .938 - 20 UNEF 1.234 (31.3) 1.443 (36.7) .830 (21.1) 1.108 (28.1) .508 (12.9)
6 18 1.062 - 18 UNEF 1.360 (34.5) 1.561 (39.6) .897 (22.8) 1.233 (31.3) .571 (14.5)
7 20 1.188 - 18 UNEF 1.485 (37.7) 1.732 (44.0) .955 (24.3) 1.477 (37.5) .748 (19.0)
8 22 1.312 - 18 UNEF 1.610 (40.9) 1.732 (44.0) 1.015 (25.8) 1.477 (37.5) .748 (19.0)
9 24 1.438 - 18 UNEF 1.735 (44.1) 2.000 (50.8) 1.077 (27.4) 1.727 (43.9) .996 (25.3)
APPLICATION NOTES
1. Finish: Anodize.
2. Assembly to be identied with manufacturer’s name and
part number, space permitting.
3. For complete dimensions, see the applicable Military
Specication.
4. Metric dimensions (mm) are in parentheses.
A Thread
C
E
F
G
H
Set Screw Wire Holes
(3 Equally Spaced)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
MS27741
TAG® Ring
For Reliable Shield Terminations
Basic
Part Number
MS27741 -10
Dash
Number
APPLICATION NOTES
1. For complete dimensions see the
applicable Military Specication.
2. Finish:
Body and Nut - Gold Iridite
Spring - Gold Plate
3. Metric dimensions (mm) are in
parentheses.
TABLE I: Shell Size, Entry, Slots and Weight
Dash
No. A Dia
Max Entry
Dia No. of
Slots Weight
in Grams
2.545 (13.8) .250 (6.4) 3 2.268
3 .670 (17.0) .375 (9.5) 4 2.722
4 .795 (20.2) .500 (12.7) 6 3.175
5 .920 (23.4) .625 (15.9) 8 4.082
6 1.045 (26.5) .750 (19.1) 10 4.536
7 1.170 (29.7) .875 (22.2) 10 4.990
8 1.295 (32.9) 1.000 (25.4) 12 5.443
9 1.420 (36.1) 1.125 (28.6) 15 6.350
10 1.687 (42.8) 1.250 (31.8) 15 10.433
11 1.812 (46.0) 1.375 (34.9) 15 14.515
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-8
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Rev 8-19-14 Printed in U.S.A.
AS31051
Dummy Stowage Receptacle
Threaded Coupling
MATING CONNECTOR
AS50151
F
H
J Thread
K
E
G Dia.
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell
Size
EF
Max
G
Max
H
Max
J Thread
Class 2A
K
Max
±.005 (.1)
8S .594 (15.1) .906 (23.0) .130 (3.3) .593 (15.1) 1/2-28 UNEF .156 (4.0)
10S .719 (18.3) 1.031 (26.2) .130 (3.3) .593 (15.1) 5/8-24 UNEF .156 (4.0)
12S .812 (20.6) 1.125 (28.6) .130 (3.3) .593 (15.1) 3/4-20 UNEF .156 (4.0)
12 .812 (20.6) 1.125 (28.6) .130 (3.3) .781 (19.8) 3/4-20 UNEF .156 (4.0)
14S .906 (23.0) 1.219 (31.0) .130 (3.3) .593 (15.1) 7/8-20 UNEF .156 (4.0)
14 .906 (23.0) 1.219 (31.0) .130 (3.3) .781 (19.8) 7/8-20 UNEF .156 (4.0)
16S .969 (24.6) 1.312 (33.3) .130 (3.3) .593 (15.1) 1-20 UNEF .156 (4.0)
16 .969 (24.6) 1.312 (33.3) .130 (3.3) .781 (19.8) 1-20 UNEF .156 (4.0)
18 1.062 (27.0) 1.406 (35.7) .130 (3.3) .781 (19.8) 1 1/8-18 UNEF .203 (5.2)
20 1.156 (29.4) 1.531 (38.9) .130 (3.3) .781 (19.8) 1 1/4-18 UNEF .203 (5.2)
22 1.250 (31.8) 1.656 (42.1) .130 (3.3) .781 (19.8) 1 3/8-18 UNEF .203 (5.2)
24 1.375 (34.9) 1.781 (45.2) .157 (4.0) .843 (21.4) 1 1/2-18 UNEF .203 (5.2)
28 1.562 (39.7) 2.031 (51.6) .157 (4.0) .843 (21.4) 1 3/4-18 UNS .203 (5.2)
32 1.750 (44.5) 2.281 (57.9) .183 (4.6) .906 (23.0) 2-18 UNS .359 (9.1)
36 1.938 (49.2) 2.531 (64.3) .183 (4.6) .906 (23.0) 2 1/4-16 UN .359 (9.1)
40 2.188 (55.6) 2.781 (70.6) .183 (4.6) .906 (23.0) 2 1/2-16 UN .359 (9.1)
44 2.375 (60.3) 3.031 (77.0) .183 (4.6) .906 (23.0) 2 3/4-16 UN .359 (9.1)
48 2.625 (66.7) 3.281 (83.3) .183 (4.6) .906 (23.0) 3-16 UN .359 (9.1)
Basic
Part No.
MS3105 -16
Dash No.
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-9
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
MS3115
Dummy Stowage Receptacle
Bayonet Coupling
MATING CONNECTOR
MIL-DTL-26482
F
G
H
JK
E
Gasket
Basic
Part No.
MS3115 -16 L
Dash No.
(Table II)
Material and Finish
A = Hard Anodize
L = Electroless Nickel
W = Cadmium Olive Drab over
Electroless Nickel
TABLE I: Dash Number, Cable Entry
and Backshell Dimensions
Shell
Size
EF
Max
G
Dim
Ø H J K
±.003 (.1) ±.005 (0.1) ±.016 (.4) ±.016 (.4)
8.471 (12.0) .828 (21.0) .594 (15.1) .120 (3.0) .478 (12.1) .062 (1.6)
10 .588 (14.9) .954 (24.2) .719 (18.3) .120 (3.0) .478 (12.1) .062 (1.6)
12 .748 (19.0) 1.047 (26.6) 812 (20.6) .120 (3.0) .478 (12.1) .062 (1.6)
14 .873 (22.2) 1.141 (29.0) .906 (23.0) .120 (3.0) .478 (12.1) .062 (1.6)
16 .998 (25.3) 1.234 (31.3) .969 (24.6) .120 (3.0) .478 (12.1) .062 (1.6)
18 1.123 (28.5) 1.328 (33.7) 1.062 (27.0) .120 (3.0) .478 (12.1) .062 (1.6)
20 1.248 (31.7) 1.453 (36.9) 1.156 (29.4) .120 (3.0) .572 (14.5) .094 (2.4)
22 1.373 (34.9) 1.578 (40.1) 1.250 (31.8) .120 (3.0) .572 (14.5) .094 (2.4)
24 1.498 (38.0) 1.703 (43.3) 1.375 (34.9) .147 (3.7) .605 (15.4) .094 (2.4)
APPLICATION NOTES
1. Assembly to be identied with manufacturer’s name and part number, space permitting.
2. For complete dimensions, see the applicable Military Specication.
3. Metric dimensions (mm) are in parentheses.
Rev. 12.23.15
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-10
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
MS3180 and MS3181
Protective Plug and Receptacle Covers
TABLE I: Shell Size, Dimensions and Attachment
Shell
Size
F
Max
G Dia
Max
H Dia
Max
J
Max
K Standard
Length (Inches) L Min
8 .562 (14.3) .719 (18.3) .734 (18.6) .562 (14.3) 3.00 (76.2) .578 (14.7)
10 .562 (14.3) .844 (21.4) .859 (21.8) .562 (14.3) 3.00 (76.2) .703 (17.9)
12 .562 (14.3) 1.000 (25.4) 1.000 (25.4) .562 (14.3) 3.50 (88.9) .891 (22.6)
14 .562 (14.3) 1.125 (28.6) 1.125 (28.6) .562 (14.3) 3.50 (88.9) 1.016 (25.8)
16 .562 (14.3) 1.250 (31.8) 1.250 (31.8) .562 (14.3) 3.50 (88.9) 1.141 (29.0)
18 .562 (14.3) 1.375 (34.9) 1.375 (34.9) .562 (14.3) 3.50 (88.9) 1.266 (32.2)
20 .625 (15.9) 1.500 (38.1) 1.500 (38.1) .562 (14.3) 4.00 (101.6) 1.391 (35.3)
22 .625 (15.9) 1.625 (41.3) 1.625 (41.3) .562 (14.3) 4.00 (101.6) 1.516 (38.5)
24 .658 (16.7) 1.750 (44.5) 1.750 (44.5) .602 (15.3) 4.00 (101.6) 1.641 (41.7)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
L
MS3181 Optional
Ring Attachment
Gasket
J
MS3181 Receptacle Cover
.167 (4.2)
Dia
Gasket
K
G
F
MS3180 Plug Cover
K
.167 (4.2)
Dia
H
Basic Part Number
MS3180 = Plug Cover
MS3181 = Receptacle Cover
MS3180 -12 C A L
Shell Size
(Table I)
Finish
A = Anodize
Length
L = Chain or Rope Length of 5
Inches (127.0 mm). Omit for
Standard (See K in Table I)
Attachment Option
C = Chain
N = Chain with Ring (MS3181 Only)
R = Wire Rope
Prior Revision D Available:
Attachment Option (Omit for None)
C = Chain
N = Chain with Ring (MS3181 Only)
Shell
Size
MS3180 -12 C
Basic Part Number
MS3180 = Plug Cover
MS3181 = Receptacle
Cover
Finish is
Cadmium
Olive Drab
MATING CONNECTOR
MIL-DTL-26482
NOTE: prior revision parts will NOT carry
the “JAN” marking
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-11
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
MS3186
Jam Nut with Safety Wire Holes
Basic
Part Number
MS3186 A -113 B
Material
A = Aluminim
S = Steel
C = CRES
Finish
A = Black Anodize (Material ‘A’ only)
B = Black Cadmium over Corrosion Resistant Steel
(Material ‘C’ only)
C = Clear Cadmium (Material ‘A’ only)
E = Electrodeposited Nickel
N = Electroless Nickel (Space Use Only)
P = Passivated (Material ‘C’ only)
T = Tin Plate (Material ‘S’ only)
W = 1,000 Hour Cadmium Olive Drab over Electroless Nickel
Dash
No.
TABLE I: Reference for Connector Shell Size
Dash
No. AS50151 MIL-
DTL-26482
MIL-DTL-
26500
MIL-DTL-
83723 I
MIL-DTL-
83723 III
MIL-DTL-
38999 I
MIL-DTL-
38999 II
MIL-
DTL-28840
MIL-
DTL-27599
101 8S -- -- -- -- -- -- -- --
102 -- 8 -- 8 -- -- -- -- --
103 10S, 10SL -- -- -- -- -- -- -- --
104 -- -- 8 -- -- -- -- -- --
105 -- -- -- -- 8 -- -- -- --
106 -- 10 -- 10 -- 9 -- -- 9
107 12S, 12 -- 10 -- 10 -- -- -- --
108 -- -- -- -- -- 11 -- -- 11
109 14S, 14 12 -- 12 -- -- 8 11 8
110 -- -- 12 -- 12 -- -- -- --
111 16S, 16 14 14 14 14 13 10 13 10, 13
112 -- -- 16 -- 16 Bay -- -- -- --
113 18 16 -- 16 16 Thd 15 12 -- 12, 15
114 -- -- -- -- -- -- -- 15 --
115 -- -- 18 -- -- -- -- -- 14, 17
116 20 18 -- 18 18 17 14 17 --
117 22 20 20 20 20 19 16 -- 16, 19
118 -- -- -- -- -- -- -- 19 --
119 -- -- 22 -- -- -- -- -- --
120 24 22 -- 22 22 21 18 -- 18, 21
121 -- 24 24 24 24 23 20 23 20, 23
122 28 -- -- -- -- 25 22 25 22, 25
123 -- -- -- -- -- -- 24 -- 24
124 -- -- -- -- -- -- -- 29 --
125 32 -- -- -- -- -- -- -- --
126 -- -- -- -- -- -- -- 33 --
127 36 -- -- -- -- -- -- -- --
128 40 -- -- -- -- -- -- -- --
129 44 -- -- -- -- -- -- -- --
130 48 -- -- -- -- -- -- -- --
d
B
C
D - Number of Slots
.045 (1.1)
Min
E
A
Threa
Safety Wire
Holes
(3 Equally
Spaced)
Rev. 11.17.15
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-12
© 2013 Glenair, Inc. Mil-Spec Backshells and Accessories U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
MS3186
Jam Nut with Safety Wire Holes
TABLE I: Reference for Connector Shell Size
Dash
No. A Thread BC
Max
D Min. No.
of Slots
Ø E
±.017 (.4) ±.017 (.4)
101 .500 -28 UNEF-2B .687 (17.4) None None .125 (3.2)
102 .5625 - 24 UNEF-2B .750 (19.1) .135 (3.4) 2 .125 (3.2)
103 .625 - 24 UNEF-2B .812 (20.6) None None .125 (3.2)
104 .625 - 20 UN-2B .812 (20.6) .135 (3.4) 2 .125 (3.2)
105 .625 - 20 UN-2B .812 (20.6) None 2 .125 (3.2)
106 .6875 - 24 UNEF-2B .875 (22.2) .135 (3.4) 1 .125 (3.2)
107 .750 - 20 UNEF-2B .937 (23.8) None 2 .125 (3.2)
108 .8125 - 20 UNEF-2B 1.000 (25.4) .135 (3.4) 1 .125 (3.2)
109 .875 - 20 UNEF-2B 1.062 (27.0) .135 (3.4) 1 .125 (3.2)
110 .9375 - 20 UNEF-2B 1.123 (28.5) None 1 .125 (3.2)
111 1.000 - 20 UNEF-2B 1.188 (30.2) .135 (3.4) 1 .125 (3.2)
112 1.125 - 20 UN-2B 1.312 (33.3) .135 (3.4) 1 .125 (3.2)
113 1.125 - 18 UNEF-2B 1.312 (33.3) .135 (3.4) 1 .125 (3.2)
114 1.1875 - 18 UNEF-2B 1.375 (34.9) None None .125 (3.2)
115 1.250 - 20 UN-2B 1.438 (36.5) None None .125 (3.2)
116 1.250 - 18 UNEF-2B 1.438 (36.5) .135 (3.4) 1 .125 (3.2)
117 1.375 - 18 UNEF-2B 1.562 (39.7) .192 (4.9) 1 .125 (3.2)
118 1.4375 - 18 UNEF-2B 1.625 (41.3) None None .125 (3.2)
119 1.500 - 20 UN-2B 1.688 (42.9) None None .125 (3.2)
120 1.500 - 18 UNEF-2B 1.688 (42.9) .192 (4.9) 1 .125 (3.2)
121 1.625 - 18 UNEF-2B 1.812 (46.0) .192 (4.9) 1 .125 (3.2)
122 1.750 - 18 UNS-2B 2.000 (50.8) .192 (4.9) 1 .125 (3.2)
123 1.875 - 16 UN-2B 2.125 (54.0) None None .125 (3.2)
124 1.9375 - 16 UN-2B 2.187 (55.5) None None .189 (4.8)
125 2.000 - 18 UNS-2B 2.250 (57.2) None None .189 (4.8)
126 2.125 - 16 UN-2B 2.375 (60.3) None None .189 (4.8)
127 2.250 - 16 UN-2B 2.500 (63.5) None None .189 (4.8)
128 2.500 - 16 UN-2B 2.750 (69.9) None None .189 (4.8)
129 2.750 - 16 UN-2B 3.000 (76.2) None None .189 (4.8)
130 3.000 - 16 UN-2B 3.250 (82.6) None None .189 (4.8)
APPLICATION NOTES
1. Assembly identied with manufacturer’s name
and part number, space permitting.
2. For complete dimensions, see the applicable
Military Specication.
3. Metric dimensions (mm) are in parentheses.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-13
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
M29504/04
181-002
Size 16 MIL-DTL-38999 Series III Type
Fiber Optic Pin Terminus
Ultra low dB loss QPL’d pin terminus for MIL-DTL-38999 Series III
.783 (19.9)
.300 (7.6)
.262 (6.7) Min. .031 (0.8)
Ø .062 (1.6) Ø A Ø .069 (1.8)
.080 (2.0)
Max Dia
Cable
.500 (12.7)
Shrink T ube
Ø.130 Max
Part Number Fiber Size Core/Cladding/Coating Ø A (Microns) Ref. M/-XXXX
-- / (Singlemode) . M/-
--S / (Singlemode) . M/-
-- / & ./ . M/-
-- / & ./ . M/-
-- / . M/-
-- / . N/A
-- / . M/-
-- .// (Polyimide) . M/-
-- .// (Polyimide) . M/-
-- // (Polyimide) . M/-
-- // (Polyimide) . M/-
-- / . N/A
-- / . M/-
-- / . M/-
-- / . M/-
-- / . N/A
Material and Finish
Ferrule: Zirconia Ceramic
Terminus Assembly: Stainless Steel/Passivate
Shrink Tube: Kynar
Notes
See Glenair assembly procedure GAP-015 for complete termination instructions.
Recommended Insertion/Extraction tool: P/N M81969/14-03 or equivalent
D38999
Series III QPL
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-14
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
M29504/05
181-001
Size 16 MIL-DTL-38999 Series III Type
Fiber Optic Socket Terminus
Ultra low dB loss QPL’d socket terminus for MIL-DTL-38999 Series III
Part Number Fiber Size
Core/Cladding/Coating (Microns) Ø A (Microns) Ref. M/-XXXX
-- / (Singlemode) . M/-
--S / (Singlemode) . M/-
-- / & ./ . M/-
-- / & ./ . M/-
-- / . M/-
-- / . N/A
-- / . M/-
-- .// (Polyimide) . M/-
-- .// (Polyimide) . M/-
-- // (Polyimide) . M/-
-- // (Polyimide) . M/-
-- / . N/A
-- / . M/-
-- / . M/-
-- / . M/-
-- / . N/A
Table II: Accessories
Part
Number Description
--S Ceramic Alignment Sleeve
--K Stainless Steel
Alignment Sleeve
--C Protective cover
.346 (8.8) .265 (6.7)
Ceramic alignment sleeve supplied
with terminus. Add K to the end of part
number development to supply with
optional stainless steel alignment sleeve
e.g. 181-001-126K.
1.132 (28.8)
1.025 (26.0)
.537 (13.6)
Protective Cover
Alignment Sleeve
.080 (2.0) Max
Dia. Cable
.500 (12.7)
Ø .069 (1.8)
Shrink T ube
Bottoming Surface
Ø A
Ø .062 (1.6)
Ø .117 (3.0) Max
Ø .130 (3.3) Max
Material and Finish
Ferrule: Zirconia Ceramic
Alignment Sleeve: Zirconia Ceramic or Stainless Steel/Passivate.
Terminus Assembly: Stainless Steel/Passivate
Spacer, Spring, and Cover: Stainless Steel/Passivate • Shrink Tube: Kynar
Notes
Alignment Sleeve & Protective Cover can also be ordered separately (Table II).
See assembly procedure GAP-015 for complete termination instructions.
Recommended Insertion/Extraction tool: P/N M81969/14-03 or equivalent
.031 (0.8)
.100 (2.5)
.158 (4.0)
Min
D38999
Series III QPL
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-15
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
MIL-DTL-83513/05
Micro-D Jackscrew Kits
Mil Spec Hardware Kits feature 300 series stainless steel.
Order One Kit Per Connector. Jackpost kits contain two posts, two hex
nuts and 2 lockwashers. Jackscrew kits contain 2 screws and 2 e-rings.
Packaged one kit (two screws or posts) per bag.
MIL SPEC JACKSCREW KITS
Conguration
Connector
Size,
Thread Size Dimensions
Mil Spec
Part Number Glenair Part
Number
Jackpost
Sizes 9 to 69
Contacts. Mil
Spec Size A to G
#2-56 UNC M83513/05-07 080-00-00-100
Size100 Only
Mil Spec Size H
#4-40 UNC M83513/05-17 080-00-00-101
Hex Head
Jackscrew
Low Prole
Sizes 9 to 69
Contacts. Mil
Spec Size A to G
#2-56 UNC-2A M83513/05-02 080-00-00-502
Size 100 Only
Mil Spec Size H
#4-40 UNC-2A M83513/05-12 080-00-00-512
Slot Head
Jackscrew
Low Prole
Sizes 9 to 69
Contacts. Mil
Spec Size A to G
#2-56 UNC-2A M83513/05-05 080-00-00-505
Size 100 Only
Mil Spec Size H
#4-40 UNC-2A M83513/05-15 080-00-00-515
Hex Head
Jackscrew
Extended
Sizes 9 to 69
Contacts. Mil
Spec Size A to G
#2-56 UNC-2A M83513/05-03 080-00-00-503
Size 100 Only
Mil Spec Size H
#4-40 UNC-2A M83513/05-13 080-00-00-513
Slot Head
Jackscrew
Extended
Sizes 9 to 69
Contacts. Mil
Spec Size A to G
#2-56 UNC-2A M83513/05-06 080-00-00-506
Size 100 Only
Mil Spec Size H
#4-40 UNC-2A M83513/05-16 080-00-00-516
.156 (3.96)
DIA MAX
.258 (6.55) MAX
#2-56 UNC 2A
.090 (2.29) MIN
PERFECT THD
.083 (2.11) DIA
.610 (15.49) MAX
.140 (3.56) DIA
.292 (7.41) MAX
#4-40 UNC 2A
.110 (2.79) MIN
PERFECT THD
.200 (5.08)
DIA MAX
.610 (15.49) MAX
.125 (3.18) DIA
.103 (2.62) MAX
.062 (1.57) HEX
.258 (6.55) MAX
#2-56 UNC 2A
.090 (2.29) MIN PERFECT THD
.083 (2.11) DIA
.140 (3.56) DIA
.187 (4.75) DIA
.062 (1.57) HEX
.098 (2.49) .292 (7.41) MAX
#4-40 UNC 2A
.110 (2.79) MIN PERFECT THD
.125 (3.18) DIA
.103 (2.62) MAX .258 (6.55) MAX
#2-56 UNC 2A
.090 (2.29) MIN PERFECT THD
.083 (2.11) DIA
.140 (3.56) DIA
.292 (7.41) MAX
#4-40 UNC 2A
.110 (2.79) MIN
PERFECT THD
.200 (5.08)
DIA MAX
.062 (1.57) HEX
.610 (15.49) MAX
.156 (3.96)
DIA MAX
.062 (1.57) HEX
.258 (6.55) MAX
#2-56 UNC 2A
.090 (2.29) MIN
PERFECT THD
.083 (2.11) DIA
.610 (15.49) MAX
.190 / .185
(4.8 / 4.7).086 (2.2)-56
UNC-2A
.125 (3.2) HEX
.086 (2.2)-56
UNC-2B .490 / .460
(12.4 / 11.7)
.185/.175
(4.7 / 4.4).112 (2.8)-40
UNC-2A
.187 (4.7) HEX
.112 (2.8)-40
UNC-2B .490 / .460
(12.4 / 11.7)
.140 (3.56) DIA
.187 (4.75) DIA
.098 (2.49)
#4-40 UNC 2A
.110 (2.79) MIN PERFECT THD
.292 (7.41) MAX
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-16
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
M83538/9S
Straight Adapter and Extender
Basic
Part Number
M83538/9S -09
Shell
Size
APPLICATION NOTES
1. For complete dimensions
see the applicable Military
Specication.
2. Material is corrosion
resistant steel.
3. Metric dimensions (mm)
are in parentheses.
TABLE I: Shell Size, Thread, Teeth and Dimensions
Shell
Size “A” Accessory
Thread B Dia
±.005 (0.13) C Number
of Teeth
09 M12x1.0-6g 0.100R .332 (8.18) 12
11 M15x1.0-6g 0.100R .440 (11.18) 16
13 M18x1.0-6g 0.100R .559 (14.20) 20
15 M22x1.0-6g 0.100R .716 (18.19) 24
17 M25x1.0-6g 0.100R .834 (21.18) 28
19 M28x1.0-6g 0.100R .952 (24.18) 32
21 M31x1.0-6g 0.100R 1.070 (27.18) 36
23 M34x1.0-6g 0.100R 1.188 (30.18) 40
CONNECTOR DESIGNATOR:
MIL-DTL-83538/4
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-17
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Misc. Backshells
and Accessories
G
M81824/1 • 070-001
MIL-Qualied Splice
In-Line, Insulated, Environmental
Product
Series Size
(Table I, Page G-18)
M81824/1 -1
1.10 ± .050
.950 Min
2X D
2X ØA
2X ØB
C
.110
.080
Mfg Code
Location
Optional Color Code
(see note 1)
Inspection
Window
Wirestop
See Note 1
ØE
G
APPLICATION NOTES
1. For complete dimensions see the applicable Military Specication.
2. One seal ring must be color coded per Table I. Splice to have matching circumferential color stripe.
3. Metric dimensions (mm) are in parentheses.
4. Material and Finish:
Splice – Copper UNS C10100 ASTM F68 or ASTM B187.
Finish – Tin plate per ASTM B 545, .00010 min thick over nickel per AMS-QQ-N-290.
Sealing material – Thermally stabilized thermoplastic.
Shrink Sleeve – transparent, heat shrinkable, cross-linked polyvinylidene uoride per AMS-DTL-23053/8.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
G-18
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Misc. Backshells
and Accessories
G
M81824/1 • 070-001
MIL-Qualied Splice
In-Line, Insulated, Environmental
Step C
1. Insert one wire into barrel of crimp splice and crimp using crimp tool and dies listed in Table II.
2. Repeat for second wire.
Table I
Size Wire
Range A Dia B Dia C D
E Dia
Mil Ref
Color
Code
(note )
Min
(Free State)
After
Recovery Ref
01 –
AWG
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.) . (.) . (.) M/- Red
02 –
AWG
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.) . (.) . (.) M/- Blue
03 –
AWG
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.)
. (.) . (.) . (.) M/- Yellow
Step D
1. Slide Insulation Sleeve over the splice until centered.
2. Apply heat using acceptable heat source for military equipment as qualied by the services for Class 2 splices.
Sealing rings shall melt and insulation sleeve shall seal around crimp splice and wires.
Table II
Part No. Wire Range F Crimp Tool Data
- , , ,  . Crimp Tool: M/-
Crimp Dies: M/-, -
OR
Crimp Tool: M/-
Crimp Dies: M/-, -
OR
Crimp Tool: M/-
Crimp Dies: None
- , ,  .
- , ,  .
Jacket
F
Center
Conductor
Insulation
Sleeve
Wire 2
Insulation
Sleeve Wire 1 Crimp Splice
Insulation
Sleeve
ASSEMBLY INSTRUCTIONS
Step A
1. Strip wires per Table II. Ends must be cut cleanly and at right angles to the
axial plane of the wire. The wire must not be deformed while making cuts.
Step B
1. Slide Insulation Sleeve onto one of the wires
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-1
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
Backshell-to-Connector
Assembly Tools
Industry
Specication
Number
Part
Identication
Number
Military
Part Number
Superseded
Glenair
Commercial
Part Number Description
Glenair Connector
Designator/
Interface
Page
No.
–– –– –– TG37 Connector Wrench for MIL-DTL-26500 and
MIL-DTL-83723 Series III MIL-DTL-26500;
MIL-DTL-83723 Series III H-2
–– MS3481 –– TG39 Connector Wrench for MIL-DTL-26482,
Ser . I & II; MIL-DTL-83723, Ser. I & NAS 1599 MIL-DTL-26482 Ser i e s I & I I ;
MIL-DTL-83723 Series I;
NAS 1599 H-3
–– –– –– TG47 Connector Wrench for MIL-DTL-22992,
Classes C, J and R MIL-DTL-22992,
Classes C, J and R H-4
–– –– –– TG48 Connector Wrench for MIL-DTL-38999, Series II MIL-DTL-38999 Series II H-5
–– –– –– TG52 Connector Wrench for MIL-C-81511,
Series II and IV MIL-C-81511 Series II & IV H-6
–– –– –– TG60 Connector Wrench for MIL-DTL-27599 and
MIL-DTL-38999, Series I MIL-DTL-27599;
MIL-DTL-38999 Series I H-7
–– –– –– TG83 Wrench for SJT Connectors (LN29729) LN29729 H-8
–– –– –– TG90 Connector Wrench For MIL-DTL-38999, Ser III MIL-DTL-38999 Series III H-9
–– –– –– 600B005 Plug and Receptacle Holder for
MIL-DTL-5015555 Series MS3100 Solder & Crimp
and MIL-DTL-83723, Series II
MIL-DTL-50155 Series MS3100
Solder and Crimp;
MIL-DTL-83723 Series II H-10
–– –– –– 600C005 Plug and Receptacle Holder for
MIL-DTL-22992 Classes C, J and R MIL-DTL-22992
Classes C, J and R H-11
–– –– –– 600D005 Plug and Receptacle Holder for
MIL-DTL-26482, Series I and II,
MIL-DTL-83723, Series I and NAS 1599
MIL-DTL-26482 Series I & II;
MIL-DTL-83723 Series I;
NAS 1599 H-12
–– –– –– 600E005 Plug and Receptacle Holder for MIL-DTL-26500
and MIL-DTL-83723 Series III MIL-DTL-26500;
MIL-DTL-83723 Series III H-13
–– –– –– 600F005 Plug and Receptacle Holder for MIL-DTL-27599
and MIL-DTL-38999 Series I MIL-DTL-27599;
MIL-DTL-38999 Series I H-14
–– –– –– 600FF005 Plug and Receptacle Holder for
MIL-DTL-38999, Series II MIL-DTL-38999 Series II H-15
–– –– –– 600G005 Plug and Recetacle Holder for MIL-DTL-28840 MIL-DTL-28840 H-16
–– –– –– 600H005 Plug and Receptacle Holder for
MIL-DTL-38999, Series III MIL-DTL-38999 Series III H-17
–– –– –– 600HH005 Plug and Receptacle Holder for
MIL-DTL-38999, Series IV MIL-DTL-38999 Series IV H-18
–– –– –– 600J005 Plug and Receptacle Holder for
MIL-DTL-81511, Series I, II, III and IV MIL-DTL-81511
Series I, II, III & IV H-19
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-2
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
TG37
Connector Wrench
MIL-DTL-26500, MIL-DTL-83723 Series III
TABLE I: Dash Number
and Dimensions
Dash
No. A Dim
± .062 (1.6) B Dia
Ref C Dia
Ref
8 1.250 (31.8) .424 (10.8) .428 (10.9)
10 1.250 (31.8) .526 (13.4) .530 (13.5)
12 1.250 (31.8) .696 (17.7) .700 (17.8)
14 2.000 (50.8) .765 (19.4) .769 (19.5)
16 2.000 (50.8) .892 (22.7) .896 (22.8)
18 2.000 (50.8) .998 (25.3) 1.002 (25.5)
20 2.000 (50.8) 1.123 (28.5) 1.127 (28.6)
22 2.000 (50.8) 1.248 (31.7) 1.252 (31.8)
24 2.000 (50.8) 1.373 (34.9) 1.377 (35.0)
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Aluminum alloy with electroless nickel
nish.
3. Polarization 10 not available for shell size 8.
4. Wrench has been designed to be used with both
threaded and bayonet style connectors.
C
B
A
5.625
(142.9)
Approx.
A
.75 (19.1)
Approx.
.75 (19.1)
Approx.
.375 (9.5)
Approx
GLENAIR, INC.
Basic Part
Number Shell
Size
TG37 -20 N
Polarization
N - Normal
6, 7, 8, 9 or 10
(See Note 3)
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-3
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
TABLE I: Shell Size and
Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref
81.250 (31.8) .362 (9.2)
10 1.250 (31.8) .490 (12.4)
12 1.250 (31.8) .607 (15.4)
14 1.250 (31.8) .732 (18.6)
16 2.000 (50.8) .857 (21.8)
18 2.000 (50.8) .962 (24.4)
20 2.000 (50.8) 1.087 (27.6)
22 2.000 (50.8) 1.212 (30.8)
24 2.000 (50.8) 1.337 (34.0)
TG39
Connector Wrench
MIL-DTL26482 Series I and II, MIL-DTL-83723 Series I and NAS 1599
B
A
5.625
(142.9)
Approx.
A
.375 (9.5)
Approx
GLENAIR, INC.
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
Basic Part
Number Dash
Number
TG39 -20
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-4
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
TG47
Connector Wrench
MIL-DTL-22992 Classes C, J & R
TABLE I: Shell Size and Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref C Dia
Ref
12 1.250 (31.8) .554 (14.1) .567 (14.4)
14 2.000 (50.8) .674 (17.1) .692 (17.6)
16 2.000 (50.8) .804 (20.4) .817 (20.8)
18 2.000 (50.8) .929 (23.6) .942 (23.9)
20 2.000 (50.8) 1.052 (26.7) 1.068 (27.1)
22 2.750 (69.9) 1.177 (29.9) 1.192 (30.3)
24 2.750 (69.9) 1.302 (33.1) 1.317 (33.5)
28 2.750 (69.9) 1.522 (38.7) 1.536 (39.0)
32 2.750 (69.9) 1.772 (45.0) 1.786 (45.4)
36 2.750 (69.9) 1.982 (50.3) 2.005 (50.9)
C
B
A
5.625
(142.9)
Approx.
A
Male
Female
.75 (19.1)
Approx.
.75 (19.1)
Approx.
.375 (9.5)
Approx
GLENAIR, INC.
Basic Part
Number Dash
Number
TG47 -20
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-5
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
TG48
Connector Wrench
MIL-DTL-38999 Series II
TABLE I: Shell Size and
Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref
8 1.250 (31.8) .362 (9.2)
10 1.250 (31.8) .490 (12.4)
12 1.250 (31.8) .607 (15.4)
14 1.250 (31.8) .732 (18.6)
16 2.000 (50.8) .857 (21.8)
18 2.000 (50.8) .962 (24.4)
20 2.000 (50.8) 1.087 (27.6)
22 2.000 (50.8) 1.212 (30.8)
24 2.000 (50.8) 1.337 (34.0)
Basic Part
Number Dash
Number
TG48 -20
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
B
A
5.625
(142.9)
Approx.
A
.385 (9.8) Max.
.375 (9.5)
Approx
GLENAIR, INC.
.390 (9.9) Max.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-6
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
TG52
Connector Wrench
MIL-C-81511 Series II & IV
TABLE I: Shell Size and Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref C Dia
Ref
8 1.250 (31.8) .382 (9.7) .386 (9.8)
10 1.250 (31.8) .507 (12.9) .511 (13.0)
14 2.000 (50.8) .757 (19.2) .761 (19.3)
16 2.000 (50.8) .883 (22.4) .887 (22.5)
18 2.000 (50.8) 1.007 (25.6) 1.011 (25.7)
Basic Part
Number Shell
Size
TG52 -14 1
Polarization
1, 2, 3, 4, 5, 6
(Omit for Normal)
C
B
A
5.625
(142.9)
Approx.
A
.75 (19.1)
Approx.
.75 (19.1)
Approx.
.375 (9.5)
Approx
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-7
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
TG60
Connector Wrench
MIL-DTL-27599, MIL-DTL-38999 Series I
TABLE I: Shell Size
and Dimensions
Shell
Size A Dim
Ref B Dia
Ref C Dia
Ref
91.250 (31.8) .442 (11.2) .647 (16.4)
11 1.250 (31.8) .570 (14.5) .647 (16.4)
13 1.250 (31.8) .687 (17.4) .647 (16.4)
15 2.000 (50.8) .812 (20.6) .647 (16.4)
17 2.000 (50.8) .937 (23.8) .647 (16.4)
19 2.000 (50.8) 1.042 (26.5) .647 (16.4)
21 2.000 (50.8) 1.167 (29.6) .617 (15.7)
23 2.000 (50.8) 1.292 (32.8) .617 (15.7)
25 2.000 (50.8) 1.417 (36.0) .617 (15.7)
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
Basic Part
Number Shell
size
TG60 -15
B
A
5.625
(142.9)
Approx.
A
.612 (15.5) Max.
.375 (9.5)
Approx
GLENAIR, INC.
C
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-8
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
TABLE I: Shell Size and
Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref
8 1.250 (31.8) .362 (9.2)
10 1.250 (31.8) .490 (12.4)
12 1.250 (31.8) .607 (15.4)
14 1.250 (31.8) .732 (18.6)
16 2.000 (50.8) .857 (21.8)
18 2.000 (50.8) .962 (24.4)
20 2.000 (50.8) 1.087 (27.6)
22 2.000 (50.8) 1.212 (30.8)
24 2.000 (50.8) 1.337 (34.0)
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
Basic Part
Number Shell
size
TG83 -20
TG83
Wrench for SJT Connectors
(LN29729)
B
A
5.625
(142.9)
Approx.
A
.375 (9.5)
Approx
GLENAIR, INC.
.626 (15.9) Max.
.632 (16.1) Max.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-9
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
TABLE I: Shell Size and Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref C Dia
Ref
09 1.250 (31.8) .438 (11.1) .441 (11.2)
11 1.250 (31.8) .566 (14.4) .569 (14.5)
13 1.250 (31.8) .678 (17.2) .682 (17.3)
15 2.000 (50.8) .802 (20.4) .811 (20.6)
17 2.000 (50.8) .928 (23.6) .931 (23.6)
19 2.000 (50.8) 1.032 (26.2) 1.037 (26.3)
21 2.000 (50.8) 1.155 (29.3) 1.162 (29.5)
23 2.750 (69.9) 1.283 (32.6) 1.288 (32.7)
25 2.750 (69.9) 1.407 (35.7) 1.411 (35.8)
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
Basic Part
Number Shell
Size
TG90 -15 A
Polarization
A, B, C, D, E
(Omit for Normal)
TG90
Connector Wrench
MIL-DTL-38999 Series III
C
B
5.625
(142.9)
Approx.
A Sq.
.375 (9.5)
Approx
GLENAIR, INC.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-10
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
600B005
Plug and Receptacle Holder
AS50151 Series AS31001 Solder and Crimp,
MIL-DTL-83723 Series II
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
08 60 .456 (11.6) .365 (9.3) 1.250 (31.8)
10 80 .575 (14.6) .440 (11.2) 1.250 (31.8)
12 110 .691 (17.6) .555 (14.1) 1.250 (31.8)
14 120 .816 (20.7) .675 (17.1) 1.250 (31.8)
16 120 .941 (23.9) .805 (20.4) 1.250 (31.8)
18 120 1.060 (26.9) .930 (23.6) 1.250 (31.8)
20 140 1.185 (30.1) 1.050 (26.7) 1.250 (31.8)
22 140 1.310 (33.3) 1.175 (29.8) 1.250 (31.8)
24 140 1.435 (36.4) 1.300 (33.0) 1.250 (31.8)
28 150 1.685 (42.8) 1.520 (38.6) 1.250 (31.8)
32 150 1.935 (49.1) 1.777 (45.0) 1.250 (31.8)
36 150 2.177 (55.3) 1.980 (50.3) 1.250 (31.8)
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
APPLICATION NOTES
1. Also mates with MIL-C-83723, Series II.
2. Metric dimensions (mm) are indicated in
parentheses.
3. Material: Case hardened carbon steel with
electroless nickel nish.
4. Receptacle and plug holder drives: 1/4" -
Shell sizes 08, 10, 12; 3/8" - Shell sizes
14 and up.
NO POLARIZATION REQUIRED
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 B 005 -16 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-11
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
600C005
Plug and Receptacle Holder
MIL-DTL-22992 Classes C, J & R
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
12 110 .824 (20.9) .552 (14.0) 1.280 (32.5)
14 120 .950 (24.1) .677 (17.2) 1.280 (32.5)
16 120 1.058 (26.9) .802 (20.4) 1.280 (32.5)
18 120 1.183 (30.0) .927 (23.5) 1.280 (32.5)
20 140 1.315 (33.4) 1.053 (26.7) 1.280 (32.5)
22 140 1.425 (36.2) 1.177 (29.9) 1.280 (32.5)
24 140 1.683 (42.7) 1.302 (33.1) 1.280 (32.5)
28 150 1.931 (49.0) 1.521 (38.6) 1.280 (32.5)
32 150 2.183 (55.4) 1.771 (45.0) 1.280 (32.5)
36 150 2.445 (62.1) 1.990 (50.5) 1.280 (32.5)
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 C 005 -18 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Case hardened carbon steel with
electroless nickel nish.
3. Receptacle and plug holder drives: 1/4” -
Shell size 12; 3/8” - Shell sizes 14 and up.
4. Consult Factory for larger sizes.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-12
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
600D005
Plug and Receptacle Holder
MIL-DTL-26482 Series I & II,
MIL-DTL-83723 Series I and NAS 1599
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque Max (In/lbs)
Series I Series II A Dia
Max B Dia
Max C Dim
Max
08 40 60 .478 (12.1) .358 (9.1) .910 (23.1)
10 40 80 .599 (15.2) .486 (12.3) .910 (23.1)
12 40 110 .758 (19.3) .598 (15.2) .910 (23.1)
14 40 120 .882 (22.4) .723 (18.4) .910 (23.1)
16 40 120 1.007 (25.6) .848 (21.5) .910 (23.1)
18 40 120 1.133 (28.8) .948 (24.1) .910 (23.1)
20 80 140 1.257 (31.9) 1.073 (27.3) .910 (23.1)
22 80 140 1.382 (35.1) 1.198 (30.4) .910 (23.1)
24 80 140 1.507 (38.3) 1.323 (33.6) .910 (23.1)
APPLICATION NOTES
1. Also mates with MIL-C-83723, Series I;
40M39569.
2. Metric dimensions (mm) are indicated in
parentheses.
3. Material: Case hardened carbon steel with
electroless nickel nish.
4. Receptacle and plug holder drives: 1/4” -
Shell sizes 08, 10, 12; 3/8” - Shell sizes
14 and up.
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 D 005 -16 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
NO POLARIZATION REQUIRED
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-13
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
600E005
Plug and Receptacle Holder
MIL-DTL-26500 and MIL-DTL-83723 Series III
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Case hardened carbon steel with
electroless nickel nish.
3. Receptacle and plug holder drives: 1/4” -
Shell sizes 08, 10, 12; 3/8” - Shell sizes 14
and up.
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
08 60 .537 (13.6) .424 (10.8) 1.031 (26.2)
10 80 .660 (16.8) .526 (13.4) 1.031 (26.2)
12 110 .830 (21.1) .696 (17.7) 1.031 (26.2)
14 120 .899 (22.8) .765 (19.4) 1.031 (26.2)
16 120 1.026 (26.1) .892 (22.7) 1.031 (26.2)
18 120 1.132 (28.8) .998 (25.3) 1.031 (26.2)
20 140 1.259 (32.0) 1.123 (28.6) 1.031 (26.2)
22 140 1.382 (35.1) 1.248 (31.7) 1.031 (26.2)
24 140 1.509 (38.3) 1.373 (34.9) 1.031 (26.2)
28* 150 1.740 (44.2) 1.623 (41.2) 1.031 (26.2)
* Non-Military standard shell size
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 E 005 -16 P N -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
Polarization
6, 7, 8, 9, 10 - Polarization
N - 1, 2, 3, 4, 5
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-14
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
600F005
Plug and Receptacle Holder
MIL-DTL-27599, MIL-DTL-38999 Series I
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 F 005 -17 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Case hardened carbon steel with
electroless nickel nish.
3. Receptacle and plug holder drives: 1/4” -
Shell sizes 08, 10, 12; 3/8” - Shell sizes 14
and up.
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
09 40 .577 (14.7) .438 (11.1) 1.031 (26.2)
11 40 .709 (18.0) .566 (14.4) 1.031 (26.2)
13 40 .829 (21.1) .678 (17.2) 1.031 (26.2)
15 40 .954 (24.2) .803 (20.4) 1.031 (26.2)
17 40 1.107 (28.1) .928 (23.6) 1.031 (26.2)
19 40 1.190 (30.2) 1.033 (26.2) 1.031 (26.2)
21 80 1.315 (33.4) 1.158 (29.4) 1.031 (26.2)
23 80 1.440 (36.6) 1.283 (32.6) 1.031 (26.2)
25 80 1.565 (39.8) 1.408 (35.8) 1.031 (26.2)
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
NO POLARIZATION REQUIRED
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-15
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
600FF005
Plug and Receptacle Holder
MIL-DTL-38999 Series II
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 FF 005 -16 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
APPLICATION NOTES
1. Also mates with 40M38277.
2. Metric dimensions (mm) are indicated in
parentheses.
3. Material: Case hardened carbon steel with
electroless nickel nish.
4. Receptacle and plug holder drives: 1/4” -
Shell sizes 08, 10, 12; 3/8” - Shell sizes 14
and up.
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
08 40 .478 (12.1) .358 (9.1) .910 (23.1)
10 40 .599 (15.2) .486 (12.3) .910 (23.1)
12 40 .758 (19.3) .603 (15.3) .910 (23.1)
14 40 .882 (22.4) .728 (18.5) .910 (23.1)
16 40 1.007 (25.6) .853 (21.7) .910 (23.1)
18 40 1.133 (28.8) .958 (24.3) .910 (23.1)
20 80 1.257 (31.9) 1.083 (27.5) .910 (23.1)
22 80 1.382 (35.1) 1.208 (30.7) .910 (23.1)
24 80 1.507 (38.3) 1.333 (33.9) .910 (23.1)
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
NO POLARIZATION REQUIRED
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-16
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
600G005
Plug and Receptacle Holder
MIL-DTL-28840
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Case hardened carbon steel with
electroless nickel nish.
3. Receptacle and plug holder drives: 1/4” -
Shell sizes 08, 10, 12; 3/8” - Shell sizes 14
and up.
TABLE I: Dash Number, Torque and Dimensions
Dash
No. Torque
Max (In/lbs) A Dia
Max B Dia
Max C Dim
Max
11 80 .697 (17.7) .502 (12.8) .945 (24.0)
13 110 .822 (20.8) .626 (15.9) .945 (24.0)
15 120 .995 (25.3) .798 (20.3) .945 (24.0)
17 120 1.058 (26.9) .868 (22.0) .945 (24.0)
19 120 1.245 (31.6) 1.035 (26.3) .945 (24.0)
23 140 1.433 (36.4) 1.220 (31.0) .945 (24.0)
25 140 1.558 (39.6) 1.381 (35.1) .945 (24.0)
29 150 1.745 (44.3) 1.547 (39.3) .945 (24.0)
33 150 1.933 (49.1) 1.739 (44.2) .945 (24.0)
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 G 005 -17 P 1 -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
Polarization
1, 2, 3, 4, 5, 6
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-17
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
600H005
Plug and Receptacle Holder
MIL-DTL-38999 Series III
TABLE I: Dash Number, Torque and Dimensions
Shell Size
Commercial Military Ref Max Torque (± 5 Inch Lbs)
Metal Composite A Dia
Max B Dia
Max C Dim
Max
09 A 60 35 .577 (14.7) .438 (11.1) 1.031 (26.2)
11 B80 35 .709 (18.0) .566 (14.4) 1.031 (26.2)
13 C 110 40 .829 (21.1) .678 (17.2) 1.031 (26.2)
15 D 120 40 .954 (24.2) .803 (20.4) 1.031 (26.2)
17 E 120 40 1.107 (28.1) .928 (23.6) 1.031 (26.2)
19 F 120 40 1.190 (30.2) 1.033 (26.2) 1.031 (26.2)
21 G 140 80 1.315 (33.4) 1.158 (29.4) 1.031 (26.2)
23 H 140 80 1.440 (36.6) 1.283 (32.6) 1.031 (26.2)
25 J 140 80 1.565 (39.8) 1.408 (35.8) 1.031 (26.2)
APPLICATION NOTES
1. Metric dimensions (mm) are indicated
in parentheses.
2. Material: Case hardened carbon
steel with electroless nickel nish.
3. Receptacle and plug holder drives:
1/4” - Shell sizes 08, 10, 12; 3/8” -
Shell sizes 14 and up.
4. Composite values apply when using
Glenair 600-091, 600-157 or 600-
007 tools.
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 H 005 -17 P N -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
Polarization
N, A, B, C, D, E
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-18
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
600HH005
Plug and Receptacle Holder
MIL-DTL-38999 Series IV
TABLE I: Dash Number, Torque and Dimensions
Shell Size
Commercial Military Ref Max Torque
(Inch Pounds) A Dia
Max B Dia
Max C Dim
Max
11 B80 .830 (21.1) .515 (13.1) 1.280 (32.5)
13 C 110 .95 0 (24.1) .650 (16.5) 1.280 (32.5)
15 D 120 1.07 0 (27.2) .775 (19.7) 1.280 (32.5)
17 E 120 1.200 (30.5) .901 (22.9) 1.280 (32.5)
19 F 120 1.280 (32.5) 1.015 (25.8) 1.280 (32.5)
21 G 140 1.400 (35.6) 1.140 (29.0) 1.280 (32.5)
23 H 140 1.530 (38.9) 1.265 (32.1) 1.280 (32.5)
25 J 140 1.66 0 (42.2) 1.392 (35.4) 1.280 (32.5)
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 HH 005 -17 P -KIT
Shell Size
(Omit for Kit)
KIT - Complete Kit
APPLICATION NOTES
1. Metric dimensions (mm) are indicated in
parentheses.
2. Material: Case hardened carbon steel with
electroless nickel nish.
3. Receptacle and plug holder drives: 1/4” -
Shell sizes 11 and 13; 3/8” - Shell sizes
15 and up.
C
BA
C
RECEPTACLE HOLDERPLUG HOLDER
NO POLARIZATION REQUIRED
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-19
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Assembly Tools
H
600J005
Plug and Receptacle Holder
MIL-DTL-81511 Series I, II, III & IV
SERIES I and III: Dash Number, Shell Size, Torque and Dimensions
Dash
Number Shell Size
Commercial Military Ref Max Torque
(± 5 Inch Lbs) A Dia
Max B Dia
Max C Dim
Max
1A08 08 A 40 .556 (14.1) .394 (10.0) .950 (24.1)
1B10 10 B 40 .681 (17.3) .519 (13.2) .950 (24.1)
1D14 14 D 40 .931 (23.6) .769 (19.5) .950 (24.1)
1E16 16 E 40 1.058 (26.9) .895 (22.7) .950 (24.1)
1F18 18 F 40 1.181 (30.0) 1.019 (25.9) .950 (24.1)
1G20 20 G 40 1.306 (33.2) 1.144 (29.1) .950 (24.1)
1H22 22 H 40 1.431 (36.3) 1.269 (32.2) .950 (24.1)
1J24 24 J 40 1.556 (39.5) 1.394 (35.4) .950 (24.1)
SERIES II and IV: Dash Number, Shell Size, Torque and Dimensions
Dash
Number Shell Size
Commercial Military Ref Max Torque
(± 5 Inch Lbs) A Dia
Max B Dia
Max C Dim
Max
2A08 08 A 40 .544 (13.8) .374 (9.5) .950 (24.1)
2B10 10 B 40 .669 (17.0) .499 (12.7) .950 (24.1)
2D14 14 D 40 .919 (23.3) .749 (19.0) .950 (24.1)
2E16 16 E 40 1.045 (26.5) .875 (22.2) .950 (24.1)
2F18 18 F 40 1.169 (29.7) .999 (25.4) .950 (24.1)
Product
Series Holder Type
P - Plug Holder
R - Receptacle Holder
Connector
Designator Basic
Number
600 J 005 -1F18 P 1 -KIT
Dash
Number
KIT - Complete Kit
Polarization
1, 2, 3, 4, 5, 6
APPLICATION NOTES
1. Metric dimensions (mm) are indicated
in parentheses.
2. Material: Case hardened carbon
steel with electroless nickel nish.
3. Receptacle and plug holder drives:
1/4” - Shell sizes 08, 10 and 12; 3/8”
- Shell sizes 14 and up.
C
BA
C
RECEPTACLE HOLDER PLUG HOLDER
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
H-20
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Dimensions in inches (millimeters) and are subject to change without notice.
Assembly Tools
H
TABLE I: Shell Size and Dimensions
Shell
Size A Dim
± .062 (1.6) B Dia
Ref C Dia
Ref
09 1.250 (31.8) .438 (11.1) .441 (11.2)
11 1.250 (31.8) .566 (14.4) .569 (14.5)
13 1.250 (31.8) .678 (17.2) .682 (17.3)
15 2.000 (50.8) .802 (20.4) .811 (20.6)
17 2.000 (50.8) .928 (23.6) .931 (23.6)
19 2.000 (50.8) 1.032 (26.2) 1.037 (26.3)
21 2.000 (50.8) 1.155 (29.3) 1.162 (29.5)
23 2.750 (69.9) 1.283 (32.6) 1.288 (32.7)
25 2.750 (69.9) 1.407 (35.7) 1.411 (35.8)
APPLICATION NOTES
1. Metric dimensions (mm) are
indicated in parentheses.
2. Material: Aluminum alloy with
electroless nickel nish.
Basic Part
Number Shell
Size
TG90 -15 A
Polarization
A, B, C, D, E
(Omit for Normal)
TG90
Connector Wrench
MIL-DTL-38999 Series III
C
B
5.625
(142.9)
Approx.
A Sq.
.375 (9.5)
Approx
GLENAIR, INC.
www.glenair.com E-Mail: sales@glenair.com
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
Dimensions in inches (millimeters) and are subject to change without notice.
© 2013 Glenair, Inc. U.S. CAGE Code 06324 Printed in U.S.A.
Quick Reference
P/N to Page No.
J
Quick-Reference
Military Standard Backshells and Accessories
Quick-Reference Part Number to Page Number Index
Part Number Page
AS25042
AS25043 G-2
AS50151 G-8
AS81511/13 F-2
AS81511/14 F-3
AS81511/14 F-5
AS81511/17
AS81511/18 F-7
AS81511/19 F-8
AS81511/20 F-9
AS81511/29 F-7
AS81511/30 F-10
AS85049/1 B-2
AS85049/2 B-3
AS85049/3 B-4
B-5
B-6
AS85049/4 B-7
B-9
B-11
AS85049/5 B-13
B-15
B-17
AS85049/6 B-19
AS85049/7 B-21
AS85049/8 B-23
AS85049/9 B-25
AS85049/10 B-27
AS85049/11 B-31
AS85049/14 B-35
AS85049/15 B-36
AS85049/16 B-36
AS85049/17 B-37
AS85049/18 B-38
AS85049/19 B-39
AS85049/20 B-41
AS85049/21 B-42
AS85049/23 B-43
AS85049/24 B-45
AS85049/25 B-47
AS85049/26 B-51
B-52
AS85049/27 B-53
AS85049/28 B-54
Part Number Page
AS85049/29 B-55
AS85049/30 B-56
AS85049/31 B-57
AS85049/33 B-58
AS85049/34 B-59
AS85049/36 B-60
AS85049/37 B-61
AS85049/38 B-62
AS85049/39 B-63
AS85049/41 B-64
AS85049/42 B-65
AS85049/43 B-66
AS85049/44 B-67
AS85049/45 B-68
AS85049/46 B-69
AS85049/47 B-70
AS85049/48 B-71
B-72
B-73
AS85049/49 B-74
AS85049/50 B-75
AS85049/51 B-76
AS85049/52 B-77
AS85049/53
AS85049/54
AS85049/55 B-78
AS85049/56
AS85049/57 B-79
AS85049/58 B-80
AS85049/59 B-81
AS85049/60 B-82
B-83
AS85049/61 B-84
AS85049/62 B-85
AS85049/63 B-86
AS85049/69 B-87
AS85049/74 B-88
AS85049/75 B-89
AS85049/76 B-90
AS85049/77 B-91
AS85049/78 B-92
AS85049/79 B-93
AS85049/80 B-94
Part Number Page
AS85049/81 B-96
AS85049/82
AS85049/83
AS85049/84 B-97
AS85049/85
AS85049/86
AS85049/87 B-99
AS85049/88
AS85049/89
AS85049/90 B-101
AS85049/91
AS85049/92 B-103
AS85049/93 B-104
AS85049/94 B-105
AS85049/95 B-106
AS85049/96 B-107
AS85049/103 B-108
AS85049/104 B-110
AS85049/105 B-112
AS85049/109 B-114
AS85049/111 B-116
AS85049/112 B-118
AS85049/114 B-120
AS85049/115 B-122
AS85049/118 B-124
AS85049/120 B-126
AS85049/121 B-128
AS85049/123 B-130
AS85049/124 B-132
AS85049/126 B-134
AS85049/127 B-136
AS85049/128-3
AS85049/128-4 B-137
AS85049/130 B-138
AS85049/139 B-140
AS85049/140
B-142
B-144
B-146
B-148
AS85049/141 B-150
B-152
B-154
AS85049/142 B-156
B-158
B-160
Part Number Page
MIL-DTL-26500 G-5
MIL-DTL-26500 G-6
MIL-DTL-28840/1 D-2
MIL-DTL-28840/2 D-3
MIL-DTL-28840/3 D-4
MIL-DTL-28840/4 D-5
MIL-DTL-28840/5 D-6
MIL-DTL-28840/6 D-7
D-8
MIL-DTL-28840/7 D-9
MIL-DTL-28840/8 D-10
D-11
MIL-DTL-28840/9 D-12
D-13
MIL-DTL-28840/13
MIL-DTL-28840/15 D-14
MIL-DTL-28840/22 D-15
MIL-DTL-28840/23 D-16
MIL-DTL-28840/24 D-17
MIL-DTL-38999
MIL-DTL-38999 C-2
MIL-DTL-38999 C-3
MIL-DTL-38999/22 C-4
MIL-DTL-38999/28 C-5
MIL-DTL-38999/32
MIL-DTL-38999/33 C-6
MIL-DTL-38999/50 C-7
MIL-DTL-83513/05 G-15
MIL-DTL-83538/9 G-16
MIL-DTL-83723/27 E-2
MIL-DTL-83723/35 E-3
E-4
E-5
MIL-DTL-83723/50 E-6
MIL-DTL-83723/59
MIL-DTL-83723/60 E-7
MIL-DTL-83723/59
MIL-DTL-83723/60 E-8
MIL-DTL-83723/70 E-9
MIL-S-81824/1 G-17
MS17349
MS17350 G-3
MS27291 G-4
Glenair, Inc.
1211 Air Way • Glendale, California • 91201-2497
Telephone: 818-247-6000 • Fax: 818-500-9912 • sales@glenair.com
www.glenair.com
Telephone:
+44-1623-638100
Facsimile:
+44-1623-638111
sales@glenair.co.uk
Glenair UK Ltd
40 Lower Oakham Way
Oakham Business Park
P.O. Box 37, Manseld
Notts, NG18 5BY England
Telephone:
06172 / 68 16 0
Facsimile:
06172 / 68 16 90
germany@glenair.com
Glenair Electric GmbH
Schaberweg 28
61348 Bad Homburg
Germany
Telephone:
+33-5-34-40-97-40
Facsimile:
+33-5-61-47-86-10
sales@glenair.fr
Glenair France SARL
7, Avenue Parmentier
Immeuble Central Parc #2
31200 Toulouse
France
Telephone:
847-679-8833
Facsimile:
847-679-8849
Glenair Microway Systems
7000 North Lawndale Avenue
Lincolnwood, IL
60712
Telephone:
+46-8-50550000
Facsimile:
+46-8-50550001
sales@glenair.se
Glenair Nordic AB
Gustav III : S Boulevard 46
S - 169 27 Solna
Sweden
© 2013 Glenair, Inc. Printed in U.S.A.
Telephone:
+34-925-89-29-88
Facsimile:
+34-925-89-29-87
sales@glenair.es
Glenair Iberica
C/ La Vega, 16
45612 Velada
Spain
Telephone:
203-741-1115
Facsimile:
203-741-0053
sales@glenair.com
Glenair Power
Products Group
860 N. Main Street Extension
Wallingford, CT
06492
Telephone:
+39-051-782811
Facsimile:
+39-051-782259
info@glenair.it
Glenair Italia S.p.A.
Via Del Lavoro, 7
40057 Quarto Inferiore –
Granarolo dell’Emilia
Bologna, Italy
INTERCONNECT
SOLUTIONS
Out of This World
Out of This World