M Series Pin and Socket Connectors
RoHS
Ready
AMP M Series
Pin and Socket Connectors
2
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series Connectors
Product Facts
Most connectors intermate-•
able with connectors made
to MIL-C-28748 require-
ments
Wide range of connector •
styles and sizes: standard
connectors (unloaded),
posted connectors (pre-
loaded) and special applica-
tion connectors (unloaded)
Complete line of accessory •
hardware for fastening, pro-
tecting, guiding, shielding,
strain relief and keying
A variety of contacts: •
signal, power, coaxial and
posted versions - many are
interchangeable and can be
intermixed in the same con-
nector housing
Full complement of applica-•
tion tooling for wire crimp
and posted terminations -
hand tools, semiautomatic
tooling and fully automatic
machines provide highly
reliable, low cost termina-
tions to meet production
requirements
Need More Information?
Call the Technical
Support Center:
1-800-522-6752.
The Center is staffed with
specialists well versed in all
AMP products and applica-
tion tooling. The Center can
provide you with:
Technical Support•
Catalogs•
Technical Documents•
Product Samples•
AMP FAX Service •
Product Information Faxed
Immediately
Authorized Distributor •
Locations
Specifications subject to change.
Consult Tyco Electronics Corporation for lat-
est design specifications.
©1968, 1970, 1972, 1974, 1978, 1985, 1990, 1996,
2001 and 2008 by Tyco Electronics Corpora-
tion. All Rights Reserved.
AMP, AMP FAX, AMPOMATOR,
AMP-O-LECTRIC, AMP-O-MATIC,
AMP-TAPETRONIC, CERTI-CRIMP, COAXICON,
LGH, POWERBAND,
PRO-CRIMPER, RAYCHEM,
TERMI-POINT and Tyco are trademarks.
Other products, logos, and company
names mentioned herein may be
trademarks of their respective owners.
Standard Housings
Posted Connectors
Special Application Connectors
3
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Table of Contents
Product Facts........................................2
Introduction ...................................... 4, 5
Material Specifications ..................................6
Current Carrying Capabilities .............................7, 8
How to Use this Catalog .................................9
Connector/Hardware Selection Guide (for Typical Applications)
Cable-to-Cable .........................................................10-17
Cable-to-Panel ......................................................... 18-25
Contacts (Description of Types) . . . . . . . . . . . . . . . . . . . . . . . . . . 26-29
Signal Contacts
Type II, Crimp, Snap-In ..................................30
Type III+, Crimp, Snap-In; Posted; Solder Versions ................ 31-35
Power Contacts
Type I, Crimp, Snap-In ..................................36
High Current Type II and Type III+ (Screw Machine, Crimp, Snap-In)........37
Type XII, Crimp, Snap-In .................................38
Coaxial Contacts
Subminiature, Crimp, Snap-In, Size 16 ................................... 39, 40
Miniature, Crimp, Snap-In, Size 12..........................41, 42
Standard Housings—Introduction ...........................44
6, 14, and 20-Positions ..................................45
26, 34 and 36-Positions ...............................46, 47
41 and 50-Positions .................................47, 48
75 and 104-Positions ...................................49
104 CF Positions (with Center Fastener) .......................50
160 CF Positions (with Center Fastener) ....................... 51
Posted Connectors—Introduction ...........................52
6, 14, 20 and 26-Positions ..............................53, 54
34 and 50 Positions .................................55, 56
75 and 104-Positions ...................................57
104 and 160 CF Positions (with Center Fastener) ................58, 59
15, 36 and 50 Positions (.200 [5.08] Grid).....................59, 60
Special Application Connectors—Introduction ................... 61
V.35 Special Application Connectors—Introduction ...............62, 63
V.35 Printed Circuit Board Connectors.......................64-67
V.35 Cable Connectors................................ 68-71
12-Positions, High Current Connector (UL Voltage Rating: 1800 V) ........72
29 CF Position Connector with Mixed Contacts (with Center Fastener)......73
42-Positions, Connector with Mixed Contacts ....................74
20-Positions, High Voltage Connector (UL Voltage Rating: 1800 V)........75
28-Positions, High Voltage Connector (UL Voltage Rating: 1800 V) ........76
14 and 34-Positions, Grounding Blocks and Fastening Hardware .........77
Hardware
Fastening Hardware .................................78-80
Guiding Hardware .................................... 81
Protective Hardware .................................82-87
Strain Relief Hardware ..................................88
Keying Hardware .....................................89
Application Tooling .................................90, 95
Technical Documents ................................96, 97
Part Number Index .................................98, 99
AMP M Series
Pin and Socket Connectors
4
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Introduction
AMP M Series connectors are
one of the most versatile and
complete pin and socket con-
nector lines available today.
From the basic molded plastic
housing, a connector can be
built up with a wide choice of
contacts and hardware to
serve in applications ranging
from sophisticated computers,
medical instrumentation and
military ground support
equipment to rugged truck
transmissions.
How this M Series
catalog is divided
The M Series catalog is
divided into six categories:
Application section•
Contacts/Tooling•
Standard Connector •
Housings
Posted Connector Housings•
Special Application •
Connector Housings
Hardware•
Following is a brief summary
of each of the six categories.
Knowing what you need
to meet your application
is made easy
Eight applications have been
illustrated with selection
charts from pages 10 through
25. These charts will assist you
to select the appropriate con-
nector housing as well as the
necessary hardware. Each
base part number is listed in
the numerical index on pages
94, 95 in order to find com-
plete information about a
particular part.
Contacts of various types
provide different functions in
M Series connector housings
Included are contacts for sig-
nal and power applications, for
coaxial cable and posted ver-
sions for backpanel wiring. A
full complement of application
tooling is available to meet
any production requirement
for terminating the crimp-type
contacts and wiring posted
contacts. A description of each
contact type is presented on
pages 26 through 29.
Application tooling for these
contacts is described on pages
90 and 91.
Standard connectors
Standard connectors are com-
prised of unloaded housings
that accept a variety of crimp,
solder and posted contacts. All
standard connector housings
will accept pins and/or sockets,
permitting various combina-
tions of contact loading.
Standard connectors are
described on pages
44 through 51.
Posted connectors
Posted connectors are
preloaded with post-type con-
tacts that accept
TERMI-POINT Clip or
wrap-type terminations.
All posted connectors are
described on pages 52 through
60.
Special Application connec-
tors
Connectors for special applica-
tion are available in
the following configurations:
V.35•
High Current•
Mixed Contact Connectors•
High Voltage•
RFI/EMI Shielded•
Grounding Blocks•
Special Application Connectors
are described on pages 61
through 77.
The right hardware for the
entire M Series connector line
Hardware is available to provide
fastening, protection, shielding,
guiding, strain relief and keying
capabilities for the entire
M Series connector line.
Application charts for properly
selecting hardware are pre-
sented on pages 10 through 25.
Detailed information on hard-
ware is located on pages 78
through 89.
5
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Introduction (Continued)
What makes the M Series
connector line so versatile
and special for a wide variety
of applications?
Compatibility• –Most
connectors intermateable
with connectors made to
MIL-C-28748 requirements.
Wide range• –Choice of con-
nector styles and sizes:
standard connectors
(unloaded), posted connec-
tors (preloaded) and special
application connectors.
Complete line• –Full line of
accessory hardware for fas-
tening, protecting, guiding,
strain relief and keying.
Variety of contacts• –Signal,
power, coaxial, and posted
versions—many are inter-
changeable and can be
intermixed in the same con-
nector housing.
Full complement of applica-•
tion tooling–For wire crimp
and posted terminationshand
tools, semiautomatic tooling
and fully automatic machines
provide highly reliable, low
cost terminations to meet
production requirements.
How to choose the appropri-
ate connector/contact/
hardware combination
Choosing the appropriate con-
nector/contact/hardware
combination is essential to the
proper function of any
AMP M Series connector. First,
a customer must evaluate
each individual application
with regards to: wire size(s);
number of circuits; available
space; fastening methods; and
needs for protection, shielding,
guiding, strain relief and key-
ing. Then, the customer must
consider the following factors
to make the appropriate selec-
tion of M Series connectors
and related components.
A - Determine Connector Type–
This decision is based on the
selected contact types, circuit
density requirements and, if
posted connectors are desired,
in-plant production capabilities
for wiring connectors using
hand tools or semiautomatic
tooling. Detailed specifications
of the various M Series connec-
tors are presented on the
following pages: Standard con-
nectors (pages 44 through 51),
Posted connectors (pages 52
through 60), Special
Application connectors (pages
61 through 77).
B - Determine Hardware–
This decision is based on the
selected connector types, and
the individual application
requirements for fastening, pro-
tection, shielding, guiding, strain
relief and keying. To assist cus-
tomers in determining the
proper hardware to use, hard-
ware selection information has
been formulated for each con-
nector type. This information is
located on pages 10 through 25.
Complete specifications of each
hardware component are pre-
sented in the Hard-ware section
of the catalog (pages 78
through 89).
C - Determine Contact Type –
This decision is based on wire
size(s) and reliability and cost
requirements of an application,
as well as the customer’s in-
plant production capabilities.
Complete specifications, includ-
ing accepted wire sizes and
available platings of all pin and
socket contacts, are presented
in the Contacts section of the
catalog (pages 30 through 43).
Application tooling for crimp-
and post-type contacts is
presented on pages 90 and 91).
AMP M Series
Pin and Socket Connectors
6
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Material Specifications
Performance Data
Temperature Rating:
Phenolic Housings,
–55°C to +150°C
Diallyl Phthalate Housings, –65°C
to +125°C
Polyester, –55°C to +130°C
Flammability Ratings: UL94V-0
Dielectric Withstanding
Voltage (at sea level):
Type II Contacts, 1500 VAC, RMS
Type III+ Contacts, 900 VAC, RMS
Durability (Mating/Unmating):
Types II and III+ Contacts, Gold
Plated: 500 cycles;
Types II and III+ Contacts,
Tin Plated:
50 cycles; Type I Contacts,
Gold Plated: 100 cycles
Note: For detailed information on the
above performance data and further
information on other performance data
such as Insulation Resistance, Thermal
Shock, Moisture Resistance, Vibration
and Physical Shock, request
AMP Product Specification No.
108-10001.
Contacts
The material composition and
construction of AMP contacts
encompass varying price
ranges and performance char-
acteristics. Specific materials
and available platings and
plating thicknesses of each
contact type are provided on
individual contact pages in
the Contact section (pages
30 thru 43). A brief descrip-
tion of each contact type is
presented on pages 26
through 29. Also, typical per-
formance data of M Series
connectors and contacts is
shown below.
Housings
M Series connector housings
are made of either diallyl
phthalate (blue), general pur-
pose phenolic (black)
or polyester (black).
Diallyl phthalate housings are
molded of material per
MIL-M-14, Type SDG. These
housings are ideally suited for
use where adverse environ-
mental conditions are an
important factor. Their advan-
tages include exceptional
stability; excellent resistance
to acids, alkalies and solvents;
low moisture absorption; and
good dielectric strength.
Phenolic housings are molded
of material per
MIL-M-14, Type CFG. The per-
formance characteristics of
these housings make them an
excellent choice
for applications in which
exceptional resistance to
acids, alkalies or solvents
is not of prime concern.
Polyester housings are
molded from a high tempera-
ture thermoplastic material
per ASTM D3220. Polyester
housings provide the high
temperature characteristics of
diallyl phthalate and phenolic,
but with a higher impact
strength.
Hardware
A variety of materials such as
plated steel, stainless steel
and aluminum, are used in
the construction of
M Series connector hardware.
This provides for the proper
operation and durability of
each hardware component,
while offering a choice of
economies to satisfy particu-
lar application requirements.
The materials of each hard-
ware component are
specified on the individual
hardware component pages
in the Hardware section
(pages 78 through 89).
Recognized under the •
Component Program of
Underwriters Laboratories
Inc. for 250 volts,
File No. E28476
Certified by Canadian •
Standards Association,
File No. LR 7189
R
Material Specifications
7
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Contract Carrying Capabilities
The total current capacity of
each contact in a given con-
nector is dependent upon the
heat rise resulting from the
combination of electrical
loads of the contacts in the
connector arrangement and
the maximum ambient tem-
perature in which the
connector will be operating.
Caution must be taken to
ensure that this combination
of conditions does not cause
the internal temperature of
the connector to exceed the
maximum operating temper-
ature of the housing material.
Several variables which must
be considered when deter-
mining this maximum current
capability for your applica-
tion are:
Connector Size - In general,
with more circuits in a con-
nector, less current per
contact can be carried.
Current Load Distribution -
Spreading those lines with
greater current loads
through-out the connector,
particularly around the
outer perimeter, will
enhance heat dissipation.
Ambient Temperature -
With higher ambient
temperatures, less current
can be carried.
Current Rating Verification
Can a contact rated at 10
amps carry 10 amps?
Maybe yes, but probably not.
The reason lies in the test
conditions used to rate the
contact. If these conditions
do not adequately reflect the
application conditions, the
actual allowable current lev-
els may be lower than
specified levels. For example,
many manufacturers, includ-
ing Tyco, test a single contact
in air. This gives an accurate
measure of the basic current-
carrying capacity of the
contact. Use the contact
alone in air and it can cer-
tainly carry 10 amperes. Use
it in a multi-position connec-
tor surrounded by other
current-carrying contacts or
in high ambient temperatures,
and the contact should carry
less current.
Similarly, as the contact ages
and stress relaxation, environ-
mental cycling, and other
degradation factors take their
toll, the contact’s current-
carrying capacity decreases.
A prudent design must set
current levels for such end-of-
design-life (EODL) conditions.
Practical current-carrying
capacity is not an absolute,
but an application-dependent
condition.
New Method Simplifies
Ratings
To help the designer set the
appropriate current level,
Tyco has developed a
method of specifying cur-
rent-carrying capacity. This
method takes into account
the various application fac-
tors that influence current
rating.
The method can be summa-
rized as follows:
The contact is aged to
EODL conditions by durabil-
ity cycling, thermal cycling,
and environmental expo-
sure.
The contact’s resistance
stability is verified.
The current necessary to
produce the specified tem-
perature rise is measured.
This T-rise is usually 30°C.
A rating factor is deter-
mined to allow derating of
multiple contacts in the
same housing and for differ-
ent conductor sizes.
Temperature
One other factor influencing
current levels is the maximum
operating temperature, for
example, 105°C. If the appli-
cation has a high ambient
temperature (over 75°C) the
contact’s T-rise is limited by
the maximum operating tem-
perature. For example, an
application temperature of
90°C limits the contact T-rise
to 15°C. Since current pro-
duces heat (the I2R law), the
current must be lowered to
limit the T-rise.
A contact’s T-rise depends
not only on its I2R Joule heat-
ing, but also on its ability to
dissipate the heat. Consider a
contact in a multi-contact
housing. Joule heating in
multiple contacts will raise
the local ambient tempera-
ture. Since the contact will
not be able to dissipate its
own heat as well by convec-
tion, the maximum T-rise will
be realized at a lower current
level. Conse-quently, the
allowable current level must
be lower to maintain an
acceptable T-rise.
For a given connector, the
current level will be set by the
loading density. A connector
containing 50% current-carry-
ing contacts will permit higher
currents (per contact) than a
connector will at 75% loading.
The loading percentage
assumes an even distribution
of contacts within the housing.
If all 10 contacts are grouped
together in one section of a
20-position
connector, the loading density
may approach 100%.
The Importance of EODL
As stated, T-rise in a contact
depends on both resistance
and current. As it ages, a con-
tact’s resistance will increase.
The contact designer will
specify a maximum resistance
for the contact, this level is the
end-of-design-life resistance.
Before the contact is tested
for current, Tyco subjects it to
a sequence of tests that exer-
cises the major failure
mechanisms and thereby sim-
ulates EODL conditions.
Conditioning includes mating
cycling, industrial mixed-flow-
ing gases, humidity and
tempera-ture cycling, and
vibration to sequentially
introduce wear, corrosion,
stress relaxation, and
mechanical disturbance.
75
60
56
50
45
35
23
7.5
60
45
30
15
0
Type XII Upgrade
Size 8 Upgrade
.125 POWERBAND
Contact
Size 8
Type XII
Type I, Type II/III+
Upgrade
Type III+, Type II,
Type III+ Posted
Size 20 Upgrade
20 DF
CONTACT CURRENT GUIDE Maximum Current (Amperes)
13 11.85
Wire Size - Larger wire will
carry more current since it
has less internal resistance
to current flow and gener-
ates less heat. The wire also
conducts heat away from
the connector.
Current Carring Capabilities
AMP M Series
Pin and Socket Connectors
8
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Presentation - Example of New Current Rating Format
The presentation of current- car-
rying capacity in AMP product
specifications includes two parts:
First, a base curve showing cur-
rent levels versus T-rise for a
single circuit and the largest wire
size (See figure 1). This repre-
sents the maximum current
capacity of the contact. The
curve is usually flat up to 75°C
ambient and then drops off. Up
to 75°C, the 30°C T-rise limits
the amount of current, and
above 75°C the current must be
reduced to keep the combina-
tion of ambient temperature
and T-rise from exceeding the
maximum operating tempera-
ture of 105°C.
Next are rating factors; a table
of multipliers to account for
connector loading and for
smaller wire sizes (See figure 2).
The designer first determines
the base current for the ambi-
ent conditions of the
application; then multiplies this
base current by the rating fac-
tors to find the current level for
the application’s loading factor
and wire size.
Graph shows the relationship between base current, ambient
temperature, and contact T-rise.
0 10 20 30 40 50 60 70 80 90 100 0
5
10
15
Single Contact
18 AWG
Ambient Temperature (C)
Current Rating (Amperes)
Rating factors allow the base current to be adjusted for various
connector loading and wire sizes.
Practical Values
The current-rating method gives
designers practical values appli-
cable to their applications. While
the specified current levels for a
contact may be lower than for
other testing methods, they are
more realistic and simplify the
system design process.
“Spec-manship” is replaced
by a realistic assessment of the
current-carrying capacity of a
Connector/Contact
Acceptability
As previously stated, choosing the
appropriate connector/contact
combination is fundamental to the
successful function of all connec-
tors. The Selection Chart, shown at
right, is designed to simplify your
choice of connectors and their
acceptable contacts. Once you
have selected the wire size, cur-
rent-carrying capacity need,
number of positions required, and
the type of contacts needed in
your choice of connector, refer to
this matrix for a quick look at
exactly what is acceptable in a
given connector type.
Note: Data is not typical of a spe-
cific M Series connector
configuration. For specific
current rating information based
on % connector loading, contact
Tyco Electronics.
To demonstrate the method of
specifying current, consider the
following application conditions;
an ambient temperature of 65°C, a
50% loading of contacts in the
housing, and 20 AWG [0.6mm2]
wire.
From Figure 1, the base current
rating is 14 ampere with 18 AWG
[0.8mm2] wire.
Figure 2, the rating factor for
50% loading and 20 AWG
[0.6mm2] wire is 0.68.
The specific rating for this appli-
cation is the product of the
base rating and the rating factor:
14 x 0.68 = 9.5 ampere
Each of the contacts can carry
9.5 ampere.
However, if the ambient tem-
perature is 80°C the allowable
T-rise becomes 25°C. The base
current must be lowered to 12.8
ampere so that the 105°C maxi-
mum operating temperature is
not exceeded. The current rat-
ing then becomes:
12.8 x 0.68 = 8.7 ampere.
18 20 22 24 26
Single 1.83.69.59.50
30% .97.80.66.57.49
50% .83.68.57.48.42
70% .65.53.45.38.33
100% .55.45.38.32.28
AWG
% Loading
Figure 2
contact under varying conditions
of temperature, connector load-
ing, and wire size.
Specific current-carrying data
based on EOL and % loading
is available from Tyco Electronics
Corporation. Please contact your
local Sales Engineer or call Tyco
Electronics Corporation.
Contact Selection Chart
Connector
Type Type I Type II High Current
Type II/III Type III+ Posted
Type III+ Type XII High Current
Type XII Mini-coax Sub-Mini
Coax
M Series
M Series
Special
Current Carrying Capabilities
9
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
How to Use the M Series Connector Catalog
The information in this
catalog has been arranged to
assist the customer in select-
ing the connector and
associated hardware that
best satisfies their require-
ments.
Four cable-to-cable and four
cable-to-panel applications
utilizing the various types of
fastening, guiding and pro-
tective hardware have been
illustrated on pages 10
through 25.
After selecting the appro-pri-
ate application to fit a
particular requirement, refer
to the indicated pages for
component selection.
Posted connectors and
Special Application connec-
tors can be substituted for
Standard Connectors where
indicated. Noted under each
Special Application
Connector is the standard
size hardware used for that
connector. Substitute into the
appropriate column of the
component selection charts.
The main portion of the
catalog is divided into five
basic sections: contacts,
standard connectors, posted
connectors, special applica-
tion connectors and
hardware. These sections
contain brief descriptions,
dimensions and other
technical information. The
remainder of the catalog con-
tains application tooling
information, a technical docu-
ments list and a numerical
index which references pages
covering all cataloged part
numbers.
How to Use this Catalog
AMP M Series
Pin and Socket Connectors
10
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Component Description Number of Positions
6 14 20 26 34
Plug Block 202758-1 201355-1 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic 202757-1 201298-1 200346-2 200512-2 200838-2
HOUSINGS Plug Block 202758-3 — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate 202757-3 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 2013800-1
Receptacle Block Polyester — — — — 200802-1
STRAIN Long — 201843-3 — 201845-2 201846-5
RELIEF Short Nickel Plated Steel 203432-1 200686-4 — 201229-5 —
CLAMPS Long — — — — —
Page 88 Short Stainless Steel — — 201237-2 — 201224-7
GUIDE
Center Male 200389-2 200389-2 200389-2 200389-2 200389-2
HARDWARE Center Female 200390-9 200390-9 200390-9 200390-9 200390-9
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
LOCKING SPRINGS1 Male—Nickel Plated Spring Steel 201921-1 201921-1 201921-1 201923-1 201925-1
Page 80 Female—Stainless Steel 201922-1 201922-1 201922-1 201918-1 201926-1
(Single Spring)
Internal Open End Nickel Plated Steel 204258-6 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — —
Pages 82 and 83 External Closed End Al Iridite — — — — —
External Closed End Nickel Plated Steel — — — — —
1Each part number contains two locking springs. Order one male and one female for each mated pair of connectors.
Cable-to-Cable
Locking Springs
Sockets
Housings
Pin Hoods
Pins
Guide Hardware
Strain Relief Clamps
Application
A
Featured Hardware
Strain Relief Clamps
Locking Springs
Pin Hoods
Guide Hardware
}
}
}
}
}
}
Connector/Hardware Selection Guide
11
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 — — — — Plug Block
201302-1 200277-2 — — — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 — — — — Plug Block HOUSINGS
201302-3 200277-4 — — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — — — — Long STRAIN
— 201182-4 — — — — Short Nickel Plated Steel RELIEF
201766-1 201847-1 — — — — Long CLAMPS
— — — — — — Short Stainless Steel Page 88
200389-2 200389-2 — — — — Center Male GUIDE
200390-9 200390-9 — — — — Center Female HARDWARE
— 1-200833-1 — — — — Corner Male Stainless Steel Page 81
— 1-200835-1 — — — — Corner Female
201921-1 201925-1 — — — — Male—Nickel Plated Spring Steel LOCKING SPRINGS1
201922-1 201926-1 — — — — Female—Stainless Steel Page 80
— — — — — — Internal Open End Nickel Plated Steel
— — — — — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— — — — — — External Closed End Nickel Plated Steel
Cable-to-Cable (Continued)
1. Confirm that Application A (at left) most closely meets
your requirements. (Other applications are shown on
pages 12 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
3. If a part number is not listed for a particular item, it is
not available.
3. If more than one part number is listed for a particular
hardware item, choose the one which best fits your
application.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings may be substituted
for these standard housings. See Special Application
Section.
This cable-to-cable application utilizes locking springs, strain
relief clamps, a pin hood for pin protection and guide hard-
ware.
The 34 and 50 position connectors can be used with either
center or corner guide hardware. If center guide hardware is
used, an additional four 4-40 screws, nuts and lockwashers are
required to secure the locking springs. Corner guides require
four guide pins and four guide sockets for each mated pair of
connectors.
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
12
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Component Description Number of Positions
6 14 20 26 34
Plug Block 202758-1 201355-1 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic 202757-1 201298-1 200346-2 200512-2 200838-2
HOUSINGS
Plug Block 202758-3 — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate 202757-3 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
STRAIN Long — 201843-3 — 201845-2 201846-5
RELIEF Short Nickel Plated Steel 203432-1 200686-4 — 201229-5 —
CLAMPS Long — — — — —
Page 88 Short Stainless Steel — — 201237-2 — 201224-7
Fixed Male 201092-4 201092-4 201092-4 201092-4 201092-4
Fixed Female Stainless Steel 201089-4 201089-4 201089-4 201089-4 201089-4
Long-Long Male — — — — —
JACKSCREWS1 Long-Long Female — — — — —
Pages 78 and 79 Long Male — — — — —
Long Female — — — — —
Short-Short Male 201827-1 201827-1 201827-1 201827-1 201827-1
Short-Short Female 201828-1 201828-1 201828-1 201828-1 201828-1
GUIDE
Center Male — — — — —
HARDWARE Center Female — — — — —
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
Internal Open End Nickel Plated Steel 204258-6 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — 202434-4
Pages 82 and 83 External Closed End Al Iridite — — — 201349-2 201350-2
External Closed End Nickel Plated Steel — — — — —
1Listed Jackscrews have 6-32 single lead threads. For corresponding Jackscrews with 6-32 double lead threads, refer to pages 78 and 79.
Tip:
Stainless Steel
Body:
Die Cast Zinc
Cable-to-Cable (Continued)
Application
B
Featured Hardware
Strain Relief Clamps
Pin Hoods
Jackscrews
Guide Hardware
Sockets
Pin Hoods
Pins
Guide Hardware
Strain Relief Clamps
Jackscrews
Housings
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
13
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 201310-1 201345-1 — — Plug Block
201302-1 200277-2 201311-1 201037-1 — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 201310-3 201345-2 — — Plug Block HOUSINGS
201302-3 200277-4 201311-3 — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — 201849-1 — — Long STRAIN
— 201182-4 200730-4 — — — Short Nickel Plated Steel RELIEF
201766-1 201847-1 201848-5 — — — Long CLAMPS
— — — — — — Short Stainless Steel Page 88
201092-4 201092-4 201092-4 201092-4 — — Fixed Male
201089-4 201089-4 201089-4 201089-4 — — Fixed Female Stainless Steel
— — — — — — Long-Long Male
— — — — — — Long-Long Female JACKSCREWS1
— — — — — — Long Male Pages 78 and 79
— — — — — — Long Female
201827-1 201827-1 201827-1 201827-1 — — Short-Short Male
201828-1 201828-1 201828-1 201828-1 — — Short-Short Female
— — — — — — Center Male GUIDE
— — — — — — Center Female HARDWARE
— 1-200833-1 1-201046-2 1-201046-2 — — Corner Male Stainless Steel Page 81
— 1-200835-1 201047-2 201047-2 — — Corner Female
— — — — — — Internal Open End Nickel Plated Steel
— 202394-2 201369-4 201364-4 — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— 201390-5 201368-4 201346-4 — — External Closed End Nickel Plated Steel
Tip:
Stainless Steel
Body:
Die Cast Zinc
Cable-to-Cable (Continued)
1. Confirm that Application B (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-11 and 14 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings may be substituted
for these standard housings. See Special Application
Section.
This cable-to-cable application utilizes jackscrews, strain relief
clamps and guide hardware. A pin hood is provided for pin
protection. Sizes 6, 14, 20, 26, and 41 do not use guide hard-
ware with this application.
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
14
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Component Description Number of Positions
6 14 20 26 34
Plug Block — 201355-1 201356-1 201359-1 1-201357-1
STANDARD Receptacle Block Phenolic — 201298-1 200346-2 200512-2 200838-2
HOUSINGS Plug Block — — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate — 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
180° Two- Al Anodized — — — — —
Piece Long Zinc Plated Steel — — — — —
Al Anodized — — — — —
180° Two- Zinc Plated Steel — — — — —
Piece Short Zinc Plated Cast Al — — — — —
SHIELDS 90° Two-Piece Long — — — — —
Pages 84 to 87 90° Two-Piece Short — — — — —
45° Two-Piece Short Nickel — — — — —
45° Two-Piece Deep Plated — — — — —
180° One-Piece Long Steel — 201378-2 — — 201384-2
180° One-Piece Short — 201360-2 201227-2 201169-2 201165-2
90° One-Piece Short — 201460-2 201468-2 201469-2
GUIDE
Center Male — 200389-2 200389-2 200389-2 200389-2
HARDWARE Center Female — 200390-2 200390-2 200390-2 200390-2
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
LOCKING SPRINGS1 Male—Nickel Plated Spring Steel — 201921-1 201921-1 201923-1 201925-1
Page 80 Female—Stainless Steel — 201922-1 201922-1 — 201926-1
Internal Open End Nickel Plated Steel — 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — —
Pages 82 and 83 External Closed End Al Iridite — — — — —
External Closed End Nickel Plated Steel — — — — —
1Each part number contains two locking springs. Order one male and one female for each mated pair of connectors.
Cable-to-Cable (Continued)
Sockets
Housings
Pin Hoods
Pins
Guide Hardware
Shields
Locking Springs
Application
C
Featured Hardware
Shields (One-piece)
Pin Hoods
Locking Springs
Guide Hardware
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
15
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 — — — — Plug Block
201302-1 200277-2 — — — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 — — — — Plug Block HOUSINGS
201302-3 200277-4 — — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — — — — 180° Two- Al Anodized
— — — — — — Piece Long Zinc Plated Steel
— — — — — — Al Anodized
— — — — — — 180° Two- Zinc Plated Steel
— — — — — — Piece Short Zinc Plated Cast Al
— — — — — — 90° Two-Piece Long SHIELDS
— — — — — — 90° Two-Piece Short Pages 84 to 87
— — — — — — 45° Two-Piece Short Nickel
— — — — — — 45° Two-Piece Deep Plated
— — — — — — 180° One-Piece Long Steel
— — — — — — 180° One-Piece Short
201486-2 201470-2 — — — — 90° One-Piece Short
200389-2 200389-2 — — — — Center Male GUIDE
200390-2 200390-2 — — — — Center Female HARDWARE
— 1-200833-1 — — — — Corner Male Stainless Steel Page 81
— 1-200835-1 — — — — Corner Female
201921-1 201925-1 — — — — Male—Nickel Plated Spring Steel LOCKING SPRINGS1
201922-1 201926-1 — — — — Female—Stainless Steel Page 80
— — — — — — Internal Open End Nickel Plated Steel
— — — — — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— — — — — — External Closed End Nickel Plated Steel
Cable-to-Cable (Continued)
1. Confirm that Application C (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-13 and 16 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings may be substituted
for these standard housings. See Special Application
Section.
This cable-to-cable application utilizes locking springs,
one- piece shields, a pin hood for pin protection and guide
hardware. The shields are available with both 180° and 90°
cable exits. The 180° shields are available in a long version
which provides pin protection in lieu of a pin hood.
A short shield and a pin hood or a long shield can be used on
one side only of a mated pair of connectors. The mating con-
nector must use a short shield.
The 34 and 50 position connectors can be used with either
center or corner guide hardware. If center guides are used, an
additional four 4-40 screws are required to secure the locking
springs. If corner guides are used, an additional two 4-40
screws will be required to attach the shield. Corner guides
require four guide pins and four guide sockets for each mated
pair of connectors.
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
16
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Sockets
Pin Hoods
Pins
Guide Hardware
Strain Relief Clamps
Jackscrews
Housings
Shields
Cable-to-Cable (Continued)
Application
D
Featured Hardware
Shields (Two-piece)
Pin Hoods
Jackscrews
Strain Relief Clamps
Guide Hardware
Component Description Number of Positions
6 14 20 26 34
Plug Block — — 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic — — 200346-2 200512-2 200838-2
HOUSINGS Plug Block — — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate — — 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
180° Two- Al Anodized — — — 201576-1 201571-1
Piece Long Nickel Plated Steel — — — 201576-2 201571-2
Al Anodized — — — — 200517-1
180° Two- Nickel Plated Steel — — 204087-1 200514-2 200517-9
Piece Short Nickel Plated Cast Al — — — — —
SHIELDS 90° Two-Piece Long — — — — —
Pages 84 to 87 90° Two-Piece Short — — — — —
45° Two-Piece Short Nickel — — — — —
45° Two-Piece Deep Plated — — — — —
180° One-Piece Long Steel — — — — —
180° One-Piece Short — — — — —
90° One-Piece Short — — — — —
STRAIN Long — — — 201845-2 201846-5
RELIEF Short Nickel Plated Steel — — — 201229-5 —
CLAMPS Long — — — — —
Page 88 Short Stainless Steel — — 201237-2 — 201224-7
Fixed Male — — 201092-4 201092-4 201092-4
Fixed Female Stainless Steel — — 201089-4 201089-4 201089-4
Long-Long Male — — — — —
JACKSCREWS1 Long-Long Female — — — — —
Pages 78 and 79 Long Male — — 201413-4 201413-4 201413-4
Long Female — — 201414-4 201414-4 201414-4
Short-Short Male — — — — —
Short-Short Female — — — — —
GUIDE
Center Male — — — — —
HARDWARE Center Female — — — — —
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
Internal Open End Nickel Plated Steel — — — — 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — 202434-4
Pages 82 and 83 External Closed End Al Iridite — — — — 201350-2
External Closed End Nickel Plated Steel — — — — —
1Listed Jackscrews have 6-32 single lead threads. For corresponding Jackscrews with 6-32 double lead threads, refer to pages 78 and 79.Erat veliquate magnibh enit,
conullam vel ea feuguercip exerili quatio er sequisci essismod magna feuis aliquatue feugait velestrud tinci tat. Duismodigna ad magna consequat ex eu feugait wis
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
17
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Cable-to-Cable (Continued)
1. Confirm that Application D (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-15 and 18 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings may be substituted for these
standard housings. See Special Application Section.
This cable-to-cable application utilizes jackscrews, a two-
piece short shield, a strain relief clamp, a pin hood for pin
protection and guide hardware.
Do not use a pin hood in combination with the shield for sizes
20, 26 and 41. A long shield may be used in lieu of pin hood
for pin protection for all sizes except the 20 position. Shields
are available with 180° cable exit and for the 50 through 104
position connectors, a 90° cable exit.
Select the appropriate jackscrew length for the type of shield
chosen as indicated by symbol ().
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 201310-1 201345-1 — — Plug Block
201302-1 200277-2 201311-1 201037-1 — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 201310-3 201345-2 — — Plug Block HOUSINGS
201302-3 200277-4 201311-3 — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— 201443-1 — — — — 180° Two- Al Anodized
202383-2 201443-2 202713-2 — — — Piece Long Nickel Plated Steel
— 200532-1 — — — — Al Anodized
202383-1 200532-2 202713-1 — — — 180° Two- Nickel Plated Steel
— — — 201131-1 — —
Piece Short
Nickel Plated Cast Al
— 203975-2 202711-3 — — — 90° Two-Piece Long SHIELDS
— 203975-1 202711-1 — — — 90° Two-Piece Short Pages 84 to 87
— — — — — — 45° Two-Piece Short Nickel
— — — — — — 45° Two-Piece Deep Plated
— — — — — — 180° One-Piece Long Steel
— — — — — — 180° One-Piece Short
— — — — — — 90° One-Piece Short
— — — 201849-3 — — Long STRAIN
— 201182-4 200730-4 — — — Short Nickel Plated Steel RELIEF
201766-1 201847-1 201848-5 — — — Long CLAMPS
— — — — — — Short Stainless Steel Page 88
201092-4 201092-4 201092-4 201092-4 — — Fixed Male
201089-4 201089-4 201089-4 201089-4 — — Fixed Female Stainless Steel
— 207234-1 207234-1 207234-1 — — Long-Long Male
— 207235-1 207235-1 207235-1 — — Long-Long Female JACKSCREWS1
201413-4 201413-4 201413-4 201413-4 — — Long Male Pages 78 and 79
201414-4 201414-4 201414-4 201414-4 — — Long Female
— — — — — — Short-Short Male
— — — — — — Short-Short Female
— — — — — — Center Male
GUIDE
— — — — — — Center Female HARDWARE
— 1-200833-1 1-201046-2 1-201046-2 — — Corner Male Stainless Steel Page 81
— 1-200835-1 201047-2 201047-2 — — Corner Female
— — — — — — Internal Open End Nickel Plated Steel
— 202394-2 201369-4 201364-4 — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— 201390-5 201368-4 201346-4 — — External Closed End Nickel Plated Steel
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
18
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Locking Springs
Sockets
Housings
Panel
Pin Hoods
Pins
Guide Hardware
Strain Relief Clamps
Application
E
Featured Hardware
Strain Relief Clamps
Locking Springs
Pin Hoods
Guide Hardware
Cable-to-Panel
Component Description Number of Positions
6 14 20 26 34
Plug Block 202758-1 201355-1 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic 202757-1 201298-1 200346-2 200512-2 200838-2
HOUSINGS Plug Block 202758-3 — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate 202757-3 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
STRAIN Long — 201843-3 — 201845-2 201846-5
RELIEF Short Nickel Plated Steel 203432-1 200686-4 — 201229-5 —
CLAMPS Long — — — — —
Page 88 Short Stainless Steel — — 201237-2 — 201224-7
GUIDE
Center Male 200389-2 200389-2 200389-2 200389-2 200389-2
HARDWARE Center Female 200390-9 200390-9 200390-9 200390-9 200390-9
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
LOCKING SPRINGS1 Male—Nickel Plated Spring Steel 201921-1 201921-1 201921-1 201923-1 201925-1
Page 80 Female—Stainless Steel 201922-1 201922-1 201922-1 — 201926-1
Internal Open End Nickel Plated Steel 204258-6 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — —
Pages 82 and 83 External Closed End Al Iridite — — — — —
External Closed End Nickel Plated Steel — — — — —
1Each part number contains two locking springs. Order one male and one female for each mated pair of connectors.
}
}
}
}
}
}
Connector/Hardware Selection Guide
19
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special application housings and posted housings may be
substituted for these standard housings. See Special
Application and Posted Connectors Sections.
This cable-to-panel application utilizes locking springs, strain
relief clamps, a pin hood for pin protection and guide hard-
ware.
The 34 and 50 position connectors can be used with either
center or corner guide hardware. If center guide hardware is
used, an additional four 4-40 screws, nuts and lockwashers
are required to secure the locking springs. Corner guides
require four guide pins and four guide sockets for each mated
pair of connectors.
1. Confirm that Application E (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-17 and 20 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Cable-to-Panel (Continued)
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 — — — — Plug Block
201302-1 200277-2 — — — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 — — — — Plug Block HOUSINGS
201302-3 200277-4 — — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — — — — Long STRAIN
— 201182-4 — — — — Short Nickel Plated Steel RELIEF
201766-1 201847-1 — — — — Long CLAMPS
— — — — — — Short Stainless Steel Page 88
200389-2 200389-2 — — — — Center Male
GUIDE
200390-9 200390-9 — — — — Center Female HARDWARE
— 1-200833-1 — — — — Corner Male Stainless Steel Page 81
— 1-200835-1 — — — — Corner Female
201921-1 201925-1 — — — — Male—Nickel Plated Spring Steel
LOCKING SPRINGS1
201922-1 201926-1 — — — — Female—Stainless Steel Page 80
— — — — — — Internal Open End Nickel Plated Steel
— — — — — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— — — — — — External Closed End Nickel Plated Steel
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
20
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Sockets
Panel
Pin Hoods
Pins
Guide Hardware
Strain Relief Clamps
Jackscrews
Housings
Application
F
Featured Hardware
Strain Relief Clamps
Pin Hoods
Jackscrews
Guide Hardware
Cable-to-Panel (Continued)
Component Description Number of Positions
6 14 20 26 34
Plug Block 202758-1 201355-1 201356-1 201359-1 1-201357-1
STANDARD Receptacle Block Phenolic 202757-1 201298-1 200346-2 200512-2 200838-2
HOUSINGS Plug Block 202758-3 — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate 202757-3 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
STRAIN Long — 201843-1 — 201845-1 201846-1
RELIEF Short Nickel Plated Steel 203432-1 200686-1 — 201229-1 —
CLAMPS Long — — — — —
Page 88 Short Stainless Steel — — 201237-1 — 201224-1
Fixed Male 201092-4 201092-4 201092-4 201092-4 201092-4
Fixed Female Stainless Steel 201089-4 201089-4 201089-4 201089-4 201089-4
Long-Long Male — — — — —
JACKSCREWS1 Long-Long Female — — — — —
Pages 78 and 79 Long Male — — — — —
Long Female — — — — —
Short-Short Male 201827-1 201827-1 201827-1 201827-1 201827-1
Short-Short Female 201828-1 201828-1 201828-1 201828-1 201828-1
GUIDE
Center Male — — — — —
HARDWARE Center Female — — — — —
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
Internal Open End Nickel Plated Steel 204258-6 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — 202434-4
Pages 82 and 83 External Closed End Al Iridite — — — 201349-2 201350-2
External Closed End Nickel Plated Steel — — — — —
1Listed Jackscrews have 6-32 single lead threads. For corresponding Jackscrews with 6-32 double lead threads, refer to pages 78 and 79.
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
21
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
1. Confirm that Application F (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-19 and 22 through 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings and posted housings may be
substituted for these standard housings. See Special
Application and Posted Connectors Sections.
This cable-to-panel application utilizes jackscrews, strain relief
clamps and guide hardware. A pin hood is provided for pin
protection. Sizes 6, 14, 20, 26, and 41 do not use guide hard-
ware for this application.
Cable-to-Panel (Continued)
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 201310-1 201345-1 — — Plug Block
201302-1 200277-2 201311-1 201037-1 — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 201310-3 201345-2 — — Plug Block HOUSINGS
201302-3 200277-4 201311-3 — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — 201849-1 — — Long STRAIN
— 201182-1 200730-1 — — — Short Nickel Plated Steel RELIEF
201766-1 201847-1 201848-1 — — — Long CLAMPS
— — — — — — Short Stainless Steel Page 88
201092-4 201092-4 201092-4 201092-4 — — Fixed Male
201089-4 201089-4 201089-4 201089-4 — — Fixed Female Stainless Steel
— — — — — — Long-Long Male
— — — — — — Long-Long Female JACKSCREWS1
— — — — — — Long Male Pages 78 and 79
— — — — — — Long Female
201827-1 201827-1 201827-1 201827-1 — — Short-Short Male
201828-1 201828-1 201828-1 201828-1 — — Short-Short Female
— — — — — — Center Male GUIDE
— — — — — — Center Female HARDWARE
— 1-200833-1 1-201046-2 1-201046-2 — — Corner Male Stainless Steel Page 81
— 1-200835-1 201047-2 201047-2 — — Corner Female
— — — — — — Internal Open End Nickel Plated Steel
— 202394-2 201369-4 201364-4 — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— 201390-5 201368-4 201346-4 — — External Closed End Nickel Plated Steel
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
22
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Locking Springs
Sockets
Housings Panel
Pin Hoods
Pins
Guide Hardware
Shields
Application
G
Featured Hardware
Shields (One-piece)
Pin Hoods
Locking Springs
Guide Hardware
Cable-to-Panel (Continued)
Component Description Number of Positions
6 14 20 26 34
Plug Block — 201355-1 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic — 201298-1 200346-2 200512-2 200838-2
HOUSINGS Plug Block — — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate — 201298-3 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
180° Two- Al Anodized — — — — —
Piece Long Nickel Plated Steel — — — — —
Al Anodized — — — — —
180° Two- Nickel Plated Steel — — — — —
Piece Short Nickel Plated Cast Al — — — — —
SHIELDS 90° Two-Piece Long — — — — —
Pages 84 to 87 90° Two-Piece Short — — — — —
45° Two-Piece Short Nickel — — — — —
45° Two-Piece Deep Plated — — — — —
180° One-Piece Long Steel — 201378-2 — — 201384-2
180° One-Piece Short — 201360-2 201227-2 201169-2 201165-2
90° One-Piece Short — — — — 201469-2
GUIDE
Center Male — 200389-2 200389-2 200389-2 200389-2
HARDWARE Center Female — 200390-9 200390-9 200390-9 200390-9
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
LOCKING SPRINGS1 Male—Nickel Plated Spring Steel — 201921-1 201921-1 201923-1 201925-1
Page 80 Female—Stainless Steel — 201922-1 201922-1 — 201926-1
Internal Open End Nickel Plated Steel — 201363-4 — 201785-4 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — —
Pages 82 and 83 External Closed End Al Iridite — — — — —
External Closed End Nickel Plated Steel — — — — —
1Each part number contains two locking springs. Order one male and one female for each mated pair of connectors.
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
23
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
1. Confirm that Application G (at left) most closely meets
your requirements. (Other applications are shown on
pages 10-21 and 24, 25.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is
not available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings and posted housings may be
substituted for these standard housings. See Special
Application and Posted Connectors Sections.
This cable-to-panel application utilizes locking springs,
one-piece shields, a pin hood for pin protection and guide
hardware. The shields are available with both 180° and 90°
cable exits. The 180° shields are available in a long version
which provides pin protection in lieu of a pin hood.
Do not select a long shield and a pin hood.
The 34 and 50 position connectors can be used with either
center or corner guide hardware. If center guides are used, an
additional four 4-40 screws are required to secure the locking
springs. If corner guides are used, an additional two 4-40
screws will be required to attach the shield. Corner guides
require four guide pins and four guide
sockets for each mated pair.
Cable-to-Panel (Continued)
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 — — — — Plug Block
201302-1 200277-2 — — — — Receptacle Block Phenolic
STANDARD
202135-4 201358-3 — — — — Plug Block HOUSINGS
201302-3 200277-4 — — — — Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— — — — — — 180° Two- Al Anodized
— — — — — — Piece Long Nickel Plated Steel
— — — — — — Al Anodized
— — — — — — 180° Two- Nickel Plated Steel
— — — — — — Piece Short Nickel Plated Cast Al
— — — — — — 90° Two-Piece Long SHIELDS
— — — — — — 90° Two-Piece Short Pages 84 to 87
— — — — — — 45° Two-Piece Short Nickel
— — — — — — 45° Two-Piece Deep Plated
— — — — — — 180° One-Piece Long Steel
— — — — — — 180° One-Piece Short
— — — — — — 90° One-Piece Short
200389-2 200389-2 — — — — Center Male GUIDE
200390-9 200390-9 — — — — Center Female HARDWARE
— 1-200833-1 — — — — Corner Male Stainless Steel Page 81
— 1-200835-1 — — — — Corner Female
201921-1 201925-1 — — — — Male—Nickel Plated Spring Steel
LOCKING SPRINGS1
201922-1 201926-1 — — — — Female—Stainless Steel Page 80
— — — — — — Internal Open End Nickel Plated Steel
— — — — — — Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— — — — — — External Closed End Nickel Plated Steel
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
24
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Jackscrews
Sockets
Housings
Panel
Pin Hoods
Pins
Guide Hardware
Shields
Application
H
Featured Hardware
Shields (Two-piece)
Pin Hoods
Guide Hardware
Jackscrews
Cable-to-Panel (Continued)
Component Description Number of Positions
6 14 20 26 34
Plug Block — — 201356-1 201359-1 1-201357-1
STANDARD
Receptacle Block Phenolic — — 200346-2 200512-2 200838-2
HOUSINGS Plug Block — — 201356-3 201359-3 201357-3
Pages 44 to 51 Receptacle Block Diallyl Phthalate — — 200346-4 200512-3 200838-3
Plug Block — — — — 213800-1
Receptacle Block Polyester — — — — 213802-1
180° Two- Al Anodized — — — 201576-1 201571-1
Piece Long Nickel Plated Steel — — — 201576-2 201571-2
Al Anodized — — — — 200517-1
180° Two- Nickel Plated Steel — — 204087-1 200514-2 200517-9
Piece Short Nickel Plated Cast Al — — — — —
SHIELDS 90° Two-Piece Long — — — — —
Pages 84 to 87 90° Two-Piece Short — — — — —
45° Two-Piece Short Nickel — — — — —
45° Two-Piece Deep Plated — — — — —
180° One-Piece Long Steel — — — — —
180° One-Piece Short — — — — —
90° One-Piece Short — — — — —
Fixed Male — — 201092-4 201092-4 201092-4
Fixed Female Stainless Steel — — 201089-4 201089-4 201089-4
Long-Long Male — — — — —
JACKSCREWS1 Long-Long Female — — — — —
Pages 78 and 79 Long Male — — 201413-4 201413-4 201413-4
Long Female — — 201414-4 201414-4 201414-4
Short-Short Male — — — — —
Short-Short Female — — — — —
GUIDE
Center Male — — — — —
HARDWARE Center Female — — — — —
Page 81 Corner Male Stainless Steel — — — — 1-200833-1
Corner Female — — — — 1-200835-1
Internal Open End Nickel Plated Steel — — — — 201786-4
PIN HOODS Internal Closed End Nickel Plated Steel — — — — 202434-4
Pages 82 and 83 External Closed End Al Iridite — — — — 201350-2
External Closed End Nickel Plated Steel — — — — —
1Listed Jackscrews have 6-32 single lead threads. For corresponding Jackscrews with 6-32 double lead threads, refer to pages 78 and 79.
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}}
}
}
}
Connector/Hardware Selection Guide
25
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
1. Confirm that Application H (at left) most closely meets
your requirements. (Other applications are shown on
pages 10 through 23.)
2. Find the appropriate column for the number of positions
required.
3. Select part numbers required for the application listed
in the column below the number of positions.
If a part number is not listed for a particular item, it is not
available.
If more than one part number is listed for a particular
hardware item, choose the one which best fits your appli-
cation.
4. Dimensional information is available on the indicated
pages under description column.
5. Select Contacts: Type II (page 30), Type III+ (pages 31
through 35) or Subminiature Coaxial (pages 40, 41).
Special application housings and posted housings may be
substituted for these standard housings. See Special
Application and Posted Connectors Sections.
This cable-to-panel application utilizes jackscrews, a two-
piece short shield, a strain relief clamp, a pin hood for pin
protection and guide hardware.
Do not use a pin hood in combination with the shield for sizes
20, 26 and 41. A long shield may be used in lieu of pin hood
for pin protection for all sizes except the 20 position. Shields
are available with 180° cable exit and for the 50 thru 104 posi-
tion connectors, a 90° cable exit. 104 CF has 90° and 45°
cable exits. 160 CF has 45° cable exit.
Select the appropriate jackscrew length for the type of shield
chosen as indicated by symbol ().
Cable-to-Panel (Continued)
Number of Positions
41 50 75 104 104 CF 160 CF Component Description
202135-2 201358-1 201310-1 201345-1 201692-4 202799-2 Plug Block
201302-1 200277-2 201311-1 201037-1 201532-4 202800-2 Receptacle Block Phenolic
STANDARD
202135-4 201358-3 201310-3 201345-2 201692-3 202799-1 Plug Block HOUSINGS
201302-3 200277-4 201311-3 — 201532-2 202800-1 Receptacle Block Diallyl Phthalate
Pages 44 to 51
— — — — 1-201692-6 — Plug Block
— — — — — — Receptacle Block Polyester
— 201443-1 — — — — 180° Two- Al Anodized
202383-2 201443-2 202713-2 — — — Piece Long Nickel Plated Steel
— 200532-1 — — — — Al Anodized
202383-1 200532-2 202713-1 — — — 180° Two- Nickel Plated Steel
— — — 201131-1 — — Piece Short Nickel Plated Cast Al
— 203975-2 202711-3 — — — 90° Two-Piece Long SHIELDS
— 203975-1 202711-1 — 202395-1 — 90° Two-Piece Short Pages 84 to 87
— — — — 202110-1 202798-1 45° Two-Piece Short Nickel
— — — — 202169-1 — 45° Two-Piece Deep Plated
— — — — — — 180° One-Piece Long Steel
— — — — — — 180° One-Piece Short
— — — — — — 90° One-Piece Short
201092-4 201092-4 201092-4 201092-4 — — Fixed Male
201089-4 201089-4 201089-4 201089-4 — — Fixed Female Stainless Steel
— 207234-1 207234-1 207234-1 — — Long-Long Male
— 207235-1 207235-1 207235-1 — — Long-Long Female JACKSCREWS1
201413-4 201413-4 201413-4 201413-4 — — Long Male Pages 78 and 79
201414-4 201414-4 201414-4 201414-4 — — Long Female
— — — — — — Short-Short Male
— — — — — — Short-Short Female
— — — — — — Center Male GUIDE
— — — — — — Center Female HARDWARE
— 1-200833-1 1-201046-2 1-201046-2 202173-8 1-201046-2 Corner Male Stainless Steel Page 81
— 1-200835-1 201047-2 201047-2 202174-5 201047-2 Corner Female
— — — — — — Internal Open End Nickel Plated Steel
— 202394-2 201369-4 201364-4 — 203743-4 Internal Closed End Nickel Plated Steel PIN HOODS
— — — — — — External Closed End Al Iridite Pages 82 and 83
— 201390-5 201368-4 201346-4 202119-2 203744-4 External Closed End Nickel Plated Steel
Tip:
Stainless Steel
Body:
Die Cast Zinc
}
}
}
}
}
}
}
}
}
Connector/Hardware Selection Guide
AMP M Series
Pin and Socket Connectors
26
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Singal Contacts
Type III+, Crimp, Snap-In, Size 16
Precision formed pin and socket contacts in Size 16. They are
used in M Series, Special M Series, “G” Series, Metrimate,
Metrimate Drawer, and CPC Series 1 and 4 connectors. Contacts
feature a high normal force which provides a low resistance in
significant applications such as dry circuit signal conditions.
Mating entry is closed-ended to prevent damage from stubbing
due to misalignment. Stainless steel spring provides superior
normal force and retention in the housing. AMP proprietary gold
plating process is designed so that specified plating thicknesses
are controlled on the inside of the socket, which is the critical
contact mating area. The contacts are formed from brass. Single
contact rating is 13 amperes at 30°C T-Rise. The single contact
rating for enhanced high current Type III+ is 24 amperes @ 30°C
T-Rise.
See page 31 for product details.
Type III+, Solder Type, Size 16
As with the crimp snap-in Type III+, these precision formed sol-
der-type contacts are also used in M Series, Special M Series,
Metrimate, Metrimate Drawer, and CPC Series 1 and 4 connec-
tors. Contacts feature a high normal force which provides a low
resistance in significant applications, such as dry circuit condi-
tions. A preformed wire barrel accepts both stranded and solid
wire, while the preformed insulation barrel provides strain relief
for various wire insulation thicknesses. Mating entry is closed-
ended to prevent damage from stubbing due to misalignment.
A stainless steel spring provides superior normal force and
retention in the housing. AMP proprietary gold plating process
is designed so that specified plating thicknesses are controlled
on the inside of the socket, which is the critical contact area.
Single contact current rating is 13 amperes at 30°C Temperature
Rise. Single contact rating for enhanced high current Type III+ is
24 amperes at 30°C T-Rise.
See pages 34 and 35 for product details.
Type III+, Solder Tab, Size 16
A companion contact style to the crimp snap-in and solder-
type, the Type III+ Solder Tab is compatible with the same AMP
connector families, and features high normal forces to provide a
low resistance in significant applications. A pre-crimped solder
tab with slot accepts various sizes of solid and stranded wire.
Mating entry is closed-ended to prevent stubbing due to mis-
alignment. A stainless steel spring provides superior normal
force and retention in the housing. AMP proprietary gold plating
process is designed so that specified plating thicknesses are
controlled on the inside of the socket, which is the critical con-
tact area. Single contact current rating is 13 amperes at 30°C
Temperature Rise.
See page 35 for product details.
Contacts
(Description of Types)
27
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Signal Contacts (Continued)
Type III+, Posted Version, Size 16
The last member of the Type III+ family of contacts, the posted
version is compatible with M Series, Special M Series,
Metrimate, Metrimate Drawer, and CPC Series 1 connectors.
Precision formed, they are pre-crimped to various post config-
urations including those that accept TERMI-POINT Clip or
wire-wrap type terminations. Contacts feature high normal
force which provides a low resistance in significant applica-
tions. Mating entry is closed-ended to prevent damage from
stubbing due to misalignment. A stainless steel spring pro-
vides superior normal force and retention in the housing. AMP
proprietary gold plating process is designed so that specified
plating thicknesses are controlled on the inside of the socket,
which is the critical contact mating area. Contacts are formed
from brass. Single contact current rating is 13 amperes at 30°C
Temperature Rise.
See page 32 for product details.
Type II, Crimp, Snap-In, Size 16
Precision screw-machined pin and socket contacts, they are
used in M Series, Special M Series, “G” Series, Metrimate,
Metrimate Drawer, and CPC Series 1 and 4 connectors.
Contacts feature high normal force which provides a low resis-
tance in significant applications such as dry circuit signal
conditions. Mating entry is closed-ended to prevent damage
from stubbing due to misalignment. A stainless steel spring
provides superior normal force and retention in the housing.
The contact bodies are machined from solid brass. Single con-
tact current rating is 13 amperes at 30°C Temperature Rise.
See page 30 for product details.
Contacts
(Description of Types)
AMP M Series
Pin and Socket Connectors
28
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Power Contacts
Type I, Crimp, Snap-In, Size 12
Precision screw-machined pin and socket, Size 12 contacts,
they are used in Special M Series and “G” Series connectors,
and are inserted into the same cavities as Miniature Coaxial
contacts. These contacts feature a high normal force which
provides a low resistance in significant applications. Mating
entry is closed-ended to prevent damage from stubbing due
to misalignment. Beryllium copper springs are used to provide
contact normal force and are assisted by a stainless steel hood
which provides anti-overstress assurance. Single contact cur-
rent rating is 23 amperes at 30°C Temperature Rise.
See page 36 for product details.
Type XII, Crimp-Type
Precision formed male and female contacts used in CPC Series
3 and 4, Special M Series and “G” Series connectors, these con-
tacts offer a low cost power option which provides additional
applied cost savings when terminated with semiautomatic
application equipment. The contact body is made from 100%
copper, which provides for excellent conductivity. Spring char-
acteristics are derived from a captive stainless steel spring
which assists the dual cantilever spring members of the female
contact. Single contact current rating is 35 amperes at 30°C
Temperature Rise.
See page 38 for product details.
High Current Upgrades
Precision screw-machined pin and socket contacts have
increased current capability. All upgraded contacts use the
high amperage Louvertac contact band. The design of this
contact allows for increased current in the same form factor.
For example, Type II/Type III+ upgraded contacts increase the
current from 13 amperes free air
to 23 amperes free air at a 30°C Temperature Rise.
See pages 37 and 39 for product details.
Contacts
(Description of Types)
29
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Coaxial Contacts
Subminiature, Crimp, Snap-In, Size 16
Precision screw-machined pin and socket, Size 16 contacts,
they are used in M Series, Special M Series, and CPC Series 1
and 4. They provide cost effective solutions in applications
where mixtures of signal, power, and coaxial cable termina-
tions are desired. The contact outer shell is made from brass,
while the center pin conductor is beryllium copper, and the
socket is brass. Both the pin and socket center conductor are
gold plated for maximum corrosion resistance and minimum
contact resistance. The retention spring is stainless steel, while
the ferrule is tin plated copper. Contact design offers applica-
tion of coaxial cable, shielded conductors, and twisted pair
wire with a voltage rating of up to 200 VRMS, and a current
rating of 1.0 ampere at 30°C Temperature Rise.
See pages 40 and 41 for product details.
Miniature, Crimp, Snap-In, Size 12
Precision screw-machined, Size 12 pin and socket contacts,
they are used in Special M Series and “G” Series connectors.
They provide cost effective solutions in applications where a
mixture of signal, power, and coaxial cable terminations is
desirable. Contact body and center wire conductor are made
from brass, and are gold plated for maximum corrosion resis-
tance and minimum contact resistance. The retention spring is
beryllium copper, and the ferrule is tin plated copper. Contact
design offers application of coaxial cable, shielded conductors,
and twisted pair wire with a voltage rating of up to 325 VRMS,
and a current rating of 7.5 amperes at 30°C Temperature Rise.
See pages 42 and 43 for product details.
Contacts
(Description of Types)
AMP M Series
Pin and Socket Connectors
30
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Singal Contacts (Continued)
Contact Size 16—Pin Diameter .062 [1.57] (Test Current, 13 Ampere)‡
Tooling Part No.
Wire Size Ins. Tape Mounted Loose Piece Contact Tape Mounted Loose Piece
Range Dia. Contact No.2 Contact No. Color Dies for Dies for Hand AWG [mm2] Range1 Pin Socket Pin Socket Code AMP-TAPETRONIC Pneumatic Tool
Machine 69875 Tool System
.035-.055 *
0.89-1.40 201611-4 — 201611-14 201613-15 Red/Red -1*91538-1**
048-.065
90230-17
or 601967-1*
1.22-1.65 — — 201334-14 201332-15 Red/Red 90249-21* -1***
.095-.110 **
28-24 0.08-0.20
2.41-2.79 — — 202410-14 202411-15 Green 1* — 601967-1
.040-.062 91538-1**
1.02-1.57 201578-4 — 201578-14 201580-15 Yellow/Red or 58541-1*1*
24-20 0.2-0.6 .055-.088
90249-2 90230-17
1.40-2.16 201330-6 201328-9 201330-14 201328-15 Yellow/Red
or 601967-1**
18 0.9-0.9 No. Ins. 91539-1-1**
(Two) (Two) Support — — 202725-14 202726-14 Blue — 90231-27 or 601967-1**
.080-.105
90136-1**
2.03-2.67 — — 202507-14 202508-15 — — — or 601967-1**
18-16 0.8-1.4 200336-6 200333-8 200336-14 200333-14 Blue/Blue 90250-1 90231-27 91539-1-1**
No. Ins. 58541-1*
Support — — ,6204219-15,6 — Blue/Blue —
or 601967-1**
3212618-23 201568-3 201570-14 201568-15 Violet/Blue 90250-1 90231-27 91539-1-1**
No. Ins. 58541-1*
14 2
Support 201570-2 — †,6,3212618-13,6,† — — — — or 601967-1**
1Overall insulation crimp diameter, including crimp barrel, must not exceed .125 [3.18].
2For AMP-TAPETRONIC Machine No. 69875, order contacts by Tape Mounted Contact No., plus packaging code “IM REEL” (5000 parts per reel).
3Grounding pin is used to provide a make-first/break-last condition when mating and unmating connector halves.
4Use turret TH502 (1-601967-6) with hand tool 601967-1.
5Use turret TH501 (1-601967-5) with hand tool 601967-1.
6Pin length is .630±.005 [16.002±.127] on these two pins.
7Die Set requires “C” Head Adapter Part No. 318161-1; Adapter Holder Part No. 356304-1 (with ratchet) or 189928-1 (without); and Power Unit
Part No. 189721-2 (hand actuated) or 189722-2 (foot actuated).
*Commercial PRO-CRIMPER II Hand Tool for field repair use only. Note: Die Set can be adapted for use with the 626 Pneumatic Tool System.
† Does not use Hand Tool 91539-1 or 601967-1.
‡ Single contact, free-air test current is not to be construed as contact rating current. Use only for testing. Refer to contact current carrying
capability information on page 8.
Insertion Tool Part No. 200893-2 (for insulation diameters .070 [1.78] or less).
Extraction Tool Part No. 305183
Type II, Screw Machine,
Crimp
Material
Contact Body - Brass
Retention Spring -
Stainless steel
Finish
Contact Body -
.000030 [0.00076] gold over
.000050 [0.00127] nickel.
Gold thickness controlled
on socket O.D.
Retention Spring -
Stainless steel
Related Product Data
Application Tooling -
Pages 76-79
Pin
Pin
Socket
.795±.010
[20.19±0.25]
.472±.0056
[11.99±0.13]
.062±.001
[1.57±0.03] Dia.
Spring
Spring
Socket Body
Pin Body
.107 Max. Dia.
[2.72]
1.087±.010
[27.61±0.25]
Socket
Signal Contacts
31
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Signal Contacts (Continued)
Contact Size 16 - Pin Diameter .062 [1.57]
(Test Current, 13 Ampere)‡
Wire SizeIns. ContactStrip Form Loose PieceTooling Part No.
Range Dia. Finish Contact No.Contact No.Loose Piece Strip Form
AWG mm2Range Pin Socket Pin Socket Hand Tool Applicators
.015-.030 Gold/Nickel2788085-3 788088-2— —567867-1***
30-28 0.05-0.090.38-0.76Sel. Gold/Nickel3788085-1 788088-1 788085-4 788088-390716-1or 567947-1***
or 680602- ***
Bright Tin 1-66425-2 1-66424-1 ——
.040-.0601Gold/Nickel266425-7 66424-7 66429-3 66428-391515-16466598- ***
30-26 0.05-0.151.02-1.52Sel. Gold/Nickel366425-8 66424-8 66429-4 66428-4
.014-.0301Gold/Nickel266393-7 66394-7 ——
0.36-0.76Sel. Gold/Nickel366393-8 66394-8 66406-4 66405-4 90225-26466585-3***
Bright Tin 1-66106-5 1-66108-5 1-66107-1 1-66109-7 91515-16466321-***
26-24 0.12-0.2 .035-.0551Gold/Nickel266106-7 66108-7 66107-3 66109-3 or or
0.89-1.40Sel. Gold/Nickel366106-8 66108-8 66107-4 66109-4 58495-1*466908-2***
Sel. Gold/Nickel4—66108-1 —66109-1
Bright Tin 2-66102-5 3-66104-0 1-66103-8 1-66105-9
.040-.0801Gold/Nickel266102-8 66104-8 66103-3 66105-3 91515-16466323- ***
1.02-2.03 Sel. Gold/Nickel366102-9 66104-9 66103-4 66105-4 or or
2-66102-2 2-66104-3 1-66103-2 1-66105-3 58495-1*466907-2***
Sel. Gold/Nickel4—66104-1 —66105-1
24-20 0.2-0.6 .060-.1205Bright Tin 1-66564-2 1-66563-1 66566-7 66565-7466383-4***
1.52-3.05 Sel. Gold/Nickel366564-8 66563-8 66566-4 66565-491542-16or 466979-1***
or 567363- ***
Bright Tin 1-66332-4 1-66331-4 1-66400-0 1-66399-091523-16466324-***
.080-.1001Gold/Nickel266332-7 66331-7 66400-3 66399-3or or
2.03-2.54 Sel. Gold/Nickel366332-8 66331-8 66400-4 66399-490225-26466942-1***
Sel. Gold/Nickel4—66331-2 —66399-2
1-66098-9S
Bright Tin1-66098-8 1-66100-9 1-66099-5 1-66101-9 91505-16or 466325- ***
18-16 0.8-1.4 .080-.1001
Gold/Nickel266098-8 66100-8 66099-3 66101-3 91523-16or or
2.03-2.54 Sel. Gold/Nickel366098-9 66100-9 66099-4 66101-4 58495-1*466906-1***
Sel. Gold/Nickel466098-6 —66099-1—
1-66359-4 1-66358-6 1-66361-2 1-66360-2
.080-.1001Bright Tin1-66359-5 1-66358-8466326- ***
Gold/Nickel266359-9 66358-9 66361-3 66360-3 91519-16or
2.03-2.54
Sel. Gold/Nickel31-66359-0 1-66358-0 66361-4 66360-4 466923-2***
18-14 0.8-2.0 1-66359-2 1-66358-3 66361-8 66360-8
Sel. Gold/Nickel4—66358-1— 66360-1
.110-.1505Bright Tin66597-8 66598-966602-8 66601-9 466958-1***
1-66598-091521-16or
2.79-3.81Sel. Gold/Nickel366597-2 66598-2 66602-2 66601-2 567364-***
1Overall insulation crimp diameter, including crimp barrel, must not
exceed .125 [3.18].
2.000015 [0.00038] gold in the mating area over .000050 [0.00127]
min. nickel.
3.000030 [0.00076] gold in the mating area, with gold flash on
remainder, over .000050 [0.00127] min. nickel.
4.000030 [0.00076] gold in the mating area, with gold gradient on
remainder, over .000050 [0.00127] min. nickel.
SStandard reeling of strip form contacts.
*Commercial PRO-CRIMPER II hand tool for field repair only. Note:
Die Set can be adapted for use with 626 Pneumatic Tool System.
Insertion Tool Part No. 91002-1 (for insulation diameters .070 [1.78]
or less), No. 200893-2 (for insulation diameters .090 [2.29] max.).
Extraction Tool Part No. 305183. (Instruction Sheet 408-1216)
***Call Technical Support for Machine Applicator Part Numbers.
‡Single contact, free-air test current is not to be construed as contact rating current. Use only for testing.
Refer to contact current carrying capability information on page 8.
77
7777
5Contacts can ONLY be used in: Metrimate; CPC Series 1 (Arr. 23-
24), Series 4 (Arr. 23-13M, 23-16M, 23-22M), and VDE connectors.
6
To use with the 626 Pneumatic Tool: remove crimping head from Straight
Action Hand Tool (SAHT), order SAHT Adapter Part No. 217201-1,
Adapter Holder Part No. 356304-1(with ratchet) or 189928-1 (without),
and Power Unit Part No. 189721-1 (hand actuated) or 189722-1 (foot
actuated).
7Phosphor bronze contact body
Type III+, Crimp,
Snap-In
Pin
Socket
Spring, Stainless Steel
Ferrule, Brass, Nickel Flash
Socket
Pin
Pin Body Spring, Stainless Steel
.390
.530 ± .010
.113
.0625 +.0010
-.0020 Dia.
Material and Finish - See chart
Contact Body - Brass or phospher bronze7
Retention Spring - Stainless steel
Related Product Data
Application Tooling - Pages 76-79
Technical Documents
114-10004 application Specification
108-10024 Product Specification
[ ]
1.588 +0.025
-0.051
[ ]
9.91 Min.
[ ]
13.46± 0.25
[ ]
2.87
Max.
Dia.
Signal Contacts
AMP M Series
Pin and Socket Connectors
32
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Singal Contacts (Continued)
Material
Contact Body and Post—Brass
Retention Spring—Stainless steel
Finish
See chart.
Pin
Pin
Socket
Socket
Type III+, Posted
(Replacement Contacts,
See Note Below)
Contact Size 16—Pin Diameter .062 [1.57] (Test Current, 13 Ampere)‡
Loose Piece Contact No.
Termination Post Contact 3 Termination High Post 2 Termination High Post 1 Termination High Post
Method Configuration Finish Pin Socket Pin Socket Pin Socket
Sel. Gold/Nickel1 66460-9 66461-9 66460-8 66461-8 66460-7 66461-7
.025 x .025 Gold/Nickel2 66460-6 66461-6 — 66461-5 66460-4 66461-4
0.64 x 0.64 Bright Tin 6-66460-6 5-66461-9 6-66460-7 5-66461-8 6-66460-5 5-66461-4
.045 x .045 Sel. Gold/Nickel1 66471-9 66473-9 — — 66471-7 66473-7
Wrap-Type
1.14 x 1.14 Bright Tin 1-66471-7 1-66473-8 — — 1-66471-6 1-66473-7
.031 x .062 Sel. Gold/Nickel1 66470-9 — — — 66470-7 —
0.79 x 1.57
TERMI-POINT .031 x .062 Sel. Gold/Nickel1 66468-9 66459-9 — — — —
Clip 0.79 x 1.57
1Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance of .200 [5.08] from mating end. Gold
thickness controlled on socket O.D.
2.000030 [0.00076] gold over .000050 [0.00127] nickel on contact body. Gold thickness controlled on socket O.D.
Posts plated tin over copper.
Extraction Tool Part No. 305183 (Instruction Sheet 408-1216)
Insertion Tool Part No. 200893-2
Note: These contacts are used as replacement contacts for all posted connectors.
‡ Single contact, free-air test current is not to be construed as contact rating current. Use only for testing. Refer to contact current carrying
capability information on page 7.
.062
[1.58]
Dia.
Ref.
.525
[13.34]
.025±.001
[0.64±0.03]
Point of Gold Plating Thk.
Measurement
Body
Brass
Post
Brass
Spring
Stainless Steel
.025
[0.64]
.100
[2.54]
Signal Contacts
33
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Signal Contacts (Continued)
[ ]
Enhanced High Current
Type III+, Crimp, Snap-In Pin Body Spring, Stainless Steel
.0625 +.0010
-.0020
1.588 +0.025
-0.051
Dia.
Pin
Socket
Spring, Stainless Steel
Ferrule, Brass, Nickel Flash
[ ]
9.91
.390 Min.
.530± .010
.113 Max.
Dia.
Material and Finish - See chart
Contact Body - Copper Nickel Alloy
Retention Spring - Stainless steel
Related Product Data
Application Tooling - Pages 76-79
Technical Documents
114-10004 application Specification
108-10024-2 Product Specification
Ratings
Base Current: Type III+ contacts: 13 amperes, 30˚C temperature rise with single contact on 14 AWG wire in free air
Enhanced High Current Type III+ contacts: 24 amperes, 30˚C temperature rise with single contact on 14 AWG wire
Temperature: -55˚C to +105˚C
[ ]
13.46± 0.25
[
]
2.87
Pin
Socket
Signal Contacts
AMP M Series
Pin and Socket Connectors
34
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Singal Contacts (Continued)
Type III+ (Precision
Formed, Crimp)
Contact Size - 6
Pin Diameter - .062 [1.57]
Material and Finish
Contact Body - Copper alloy, plated
tin or gold
Spring - Stainless steel
Related Product Data
Performance Characteristics -
Page 6
Application Tooling - Pages 76-79
Technical Documents - Page 80
Grounding Pin
(make first - break last)
Wire Size Range Ins. Grounding Pin Part No. Strip Form Loose Piece
Dia. Contact Applicator Hand Tool□
mm2 AWG Range1 Finish Strip Form Loose Piece Part No. Part No.
.035-.055 Tin 164159-3 164162-1 — 91515-15 or
0.12-0.2 26-24 0.89-1.4 Sel. Gold/Nickel4 164159-4 164162-2 58495-1*
.045-.070 Bright Tin 164160-3 164163-1 466323-□*** 91515-15 or
0.2-0.6 24-20 1.14-1.78 or 91505-15 or
Sel. Gold/Nickel4 164160-4 164163-2 466907-2*** 58495-1*
.078-.098 Tin 164161-3 164164-1 466741-□*** 91523-15 or
0.8-1.4 18-16 1.98-2.49 or 91505-15 or
Sel. Gold/Nickel4 164161-4 164164-2 680114-3*** 58495-1*
1Overall insulation crimp diameter, including crimp barrel, must not exceed .125 [3.18].
4Gold flash over .000030 [0.00076] min. nickel on entire contact, with .000030 [0.00076] gold in contact area.
5To use with the 626 Pneumatic Tool System: remove the crimping head from the Straight Action Hand Tool (SAHT) Assembly, order SAHT
Adapter Part No. 217201-1, Adapter Holder Part No. 356304-1 (with ratchet) or 189928-1 (without), and Power Unit Part No. 189721-1 (hand
actuated) or 189722-1 (foot actuated).
*Commercial PRO-CRIMPER II hand tool for field repair only. Note: Die Set can be adapted for use with the 626 Pneumatic Tool System.
***Call Technical Support for Automatic Machine Applicator Part Numbers.
Extraction Tool Part No. 539972-1.
Pin Socket
Material
Body - Copper alloy
Louvertac Band - Beryllium copper
Retention Spring - Stainless steel
Finish
Body - Silver
Louvertac Band - Gold
High Current Power
Contact—Size 16
The features of the High Current Size
16 contact have been designed to ret-
rofit into the existing AMP Connectors
such as CPC (Circular Plastic Connec-
tor), CMC (Circular Metal Connector),
G Series, M Series, Metrimate Square
Grid and Drawer Connector housings.
An initial T-Rise test in free air has
shown a 23 amp capability with a 30°
T-Rise. The contact may be crimped
onto 14 AWG wire with an AMP hand
tool Part No. 601967-1. Use turret
TH502 (1-601967-6) for the pin and
turret TH501 (1-601967-5) for the
socket.
Contact Part Nos. Crimping Tool
Wire Range Pin Socket Turret
mm2 AWG Loose Tape Loose Tape Tool for for
Piece Mounted Piece Mounted Pins Sockets
0.8-1.4 18-16 796964-1 796964-2 796966-1 796966-2 601967-1 1-601967-6 1-601967-5
2 14 193844-1 193844-2 193846-1 193846-2 601967-1 1-601967-6 1-601967-5
Extraction Tool Part No. 305183
Signal Contacts
35
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Signal Contacts (Continued)
Wire Size ContactLoose Piece
Range FinishContact No.
AWG mm2Pin Socket
26-20 0.12-0.6 Gold /Nickel166182-1 66183-1
18-16 0.8-1.4 Gold /Nickel166180-166181-1
Solder Tab4Duplex 2202236-7 202237-7
Bright Tin202236-5202237-5
1.000030 [0.00076] gold in mating area over .000030 [0.00076] min. nickel.
2Duplex plated .000030 [0.00076] gold in mating area over .000030 [0.00076] min. nickel on contact body; bright tin on
solder tab.
3Bright tin on entire contact.
4Designed for up to 14 AWG; but, not to exceed current limitation of contact.
Note:These contacts can be used in Multimate contact cavities of all connector housings.
‡Single contact, free-air test current is not to be construed as contact rating current. Use only for testing.
Refer to contact current carrying capability information on page 8.
Extraction Tool Part No. 305183
Contact Size 16—Pin Diameter .062 [1.57] (Test Current, 13 Ampere)‡
Pin Socket
Solder-Tab
Pin Socket
Solder-Type
(with Preformed Wire Barrel/Insulation Support)
Pin Socket
Solder-Type
Pin Socket
Solder-Tab
Type III+ (Precision
Formed, Solder)
Contact Size - 16
Pin Diameter - .062 [1.57]
Material and Finish
Contact Body - Copper alloy, plated
tin to gold
Spring - Stainless steel
Related Product Data
Performance Characteristics -
Page 6
Technical Documents - Page 80
Signal Contacts
AMP M Series
Pin and Socket Connectors
36
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Power Contacts
Type I, Crimp, Snap-In
Material
Contact Body - Bronze
Retention Spring - Beryllium copper
Finish
Contact Body - .000030 [0.00076]
gold over .000050 [0.00127] nickel.
Gold thickness controlled on socket O.D.
Retention Spring - Nickel plated
Related Product Data
Application Tooling - Pages 90, 91
Technical Documents
108-10108 Product Specification
114-10037 Application Specification
Pin
Pin
Socket
Size 12—Pin Diameter .094 [2.39] (Test Current, 23 Ampere)‡
Tooling Part No.
Wire Size Loose Piece Dies for
Range Contact No. Pneumatic Hand
AWG [mm2] Pin Socket Tool* Tool
18-16 0.8-1.4 202421-1 202418-1 90122 90121
14-12 2-3 202422-1 202417-1 90122 90121
* Use hand actuated Power Unit Part No. 189721-2 or foot actuated Power
Unit Part No. 189722-2. Both units require “C” Head Die Set Adapter
Part No. 318161-1 and an Adapter Holder Part No. 356304-1 (with ratchet)
or Part No. 189928-1 (without ratchet). Request Catalog 124208 for more
information on the 626 Pneumatic Tool System.
‡ Single contact, free-air test current; not to be construed as contact rating
current. Use only for testing. Refer to contact current carrying capability
information, page 7.
Extraction Tool Part No. 305183-8 (Instruction Sheet 408-1216)
.953
[24.21]
Ref. .663
[16.84] Max.
.449
[11.40]
.150
[3.81] Dia.
.150
[3.81] Dia.
.843
[21.41] Ref.
.560
[14.25 ] Max.
.222
[5.64] Dia. Max.
Accommodates
.094±.001
[2.39±.025]
Dia. Pin
.222
[5.64] Dia. Max.
.094±.001
[2.39±.025] Dia.
Socket
Power Contacts
37
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Power Contacts (Continued)
Type XII, Precision
Formed, Crimp, Snap-In
Material
Copper
Finish
A - Tin
B - .000030 [0.00076] selective
gold over .000030 [0.00076]
nickel
C - .000100 [0.00254] silver plated
contacts with lubricant added
D - RoHS compliant Tin plating
Test Current Rating
Silver or Gold - 35 amperes ‡
Tin or Lead - 15 amperes ‡
‡ Single contact, free-air test cur-
rent; not to be construed as
contact rating current. Use only
for testing. Refer to contact cur-
rent carrying capability
information, page 7.
Related Product Data
Application Tooling -
Pages 90, 91
Technical Documents -
Pages 92, 93
Male
Female
Female
Male
Strip Form Contact Part Nos. Loose Piece Tooling
Wire Size Ins. Heavy Duty Contact Heavy Duty Die Set for
Range1 Dia. Contact Standard*** Miniature*** Part Nos. Miniature Hand Tool 69710-1
Range Finish Applicator or 626 Pneumatic
AWG mm2 Male Female Male Female Male Female Tool System
66255-1 66740-7 66255-5 1-66740-2 66261-1 66740-8
A 266256-12 — 266256-52 — 266262-12 —
16 1.25-1.4 .135-.160 66255-2 66740-5 66255-6 1-66740-1 66261-2 66740-6 90145-23,7
and and 3.43-4.06 B 266256-22 — 266256-42 — 266262-22 — 567455-□*** and
14-12 2-3
66255-7 66740-1 66255-8 1-66740-9 66261-4 66740-2
90145-14,7
5C5
266256-62 — 266256-72 — 266262-42 —
16 1-66255-1 1-66740-9 1-66255-2 2-66740-0 66261-5 2-66740-1
and
D 266256-82 — 266256-92 — 266262-52 —
14-12
66253-1 66741-7 66253-5 1-66741-2 66259-1 66741-8
A 266254-12 — — — 266260-12 —
.190-.220 66253-2 66741-5 66253-6 1-66741-1 66259-2 66741-6
10 5-6 4.83-5.59 B 266254-22 — 66252-52 — 266260-22 — 567021-□*** 90140-17
66253-4 66741-1 66253-8 1-66741-9 66259-4 66741-2
5C5
266254-42 — — — 266260-42 —
66253-9 1-66741-9 1-66253-0 2-66741-0 66259-5 2-66741-1
10
D 266254-62 — 2— — 266260-52 —
1Wire strip length—.281 [7.14].
2Ground contact.
3Die insert Part No. 90145-2 is for crimping 16 AWG [1.25-1.4 mm2] wire.
4Die insert Part No. 90145-1 is for crimping 14-12 AWG [2-3 mm2] wire.
5Recommended for high current/vibration applications where fretting corrosion is a problem.
7 Die Set requires “C” Head Adapter Part No. 318161-1; Adapter Holder Part No. 356304-1 (with ratchet) or 189928-1 (without); and Power
Unit Part No. 189721-2 (hand actuated) or 189722-2 (foot actuated).
Extraction Tool Part No. 91019-3
***Call the Technical Support Center at 1-800-522-6752 for Automatic Machine Applicator Part Numbers.
.637
[16.18] .185
[4.7]
.085
[2.16] .200
[5.08] Min.
.230
[5.84] Max.
.230
[ 5.84 ] Max.
.230
[ 5.84] Max.
.978
[24.84 ]Ref.
1.500
[38.1] Ref.
1.267
[32.18] Ref.
.287±.006
[7.29±0.152]
.287
[7.29]
.230
[5.84] Max.
.015
[0.38] Cutoff
(Loose Piece Only)
.027
[0.686] Ref.
.027
[0.686]
Ref.
Extraction Tool Part No. 91019-3
.615
[15.62]
Power Contacts
AMP M Series
Pin and Socket Connectors
38
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Type XII, Crimp, Snap-In
The Multimate features of the
High Current Type XII contact
have been designed to fit into
the existing AMP Connectors
such as CPC (Circular Plastic
Connector), CMC (Circular
Metal-Shell Connector), G
Series, and M Series housings.
An initial T-Rise test in free air
has shown a 60 amp capability
with a 30° T-Rise with 8 gage
wires. The contact may be
crimped onto 8 AWG wire with
a Daniels Hand Tool M310 or
AMP P/N 356114-1 and
Positioner TP1068S or AMP P/N
356119-1.
Material
Body - Copper alloy
Louvertac Band -
Beryllium copper
Retention Spring -
Stainless steel
Finish
Body - Silver
Louvertac Band - Gold
Cable-to-Cable
Extraction Tool
Part No. 224155-1
Current-Carrying Capacity.
The graph shows current-car-
rying capacity versus
temperature rise for a fully
energized 3 position CPC
plug P/N 206037-2 and
receptacle P/N 206036-2.
These initial representative
amperage ratings were con-
ducted with 8 AWG wires
that were 3 feet long.
Standard
Type XII Pin
(Page 38)
Notes: 1. High Current contacts with Louvertac bands are not intermateable with any other contact.
2. Additional information on CPC and CMC connectors is available in Tyco Electronics Catalog No. 82021.
3. Additional information on G Series connectors is available in Tyco Electronics Catalog No. 82046.
4. Additional information on M Series connectors is available in Tyco Electronics Catalog No. 82003.
5. Additional information on LGH connectors is available in Tyco Electronics Catalog No. 82024.
High Current
Type XII Socket
Part No. 193990-2
High Current
Type XII Pin
Part No. 193991-4
Power Contacts (Continued)
Standard
Type XII Socket
(Page 38)
Power Contacts
39
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Coaxial Contacts
Subminiature, Crimp,
Snap-In, Size 16
Material
Outer Shell - Brass per
MIL-C-50
Center Conductor - Beryllium
copper per QQ-C-533 (Pin);
Brass per QQ-B-626 (Socket)
Inner Dielectric -
Polypropylene
Retention Spring - Stainless
steel per QQ-S-766
Ferrule - Copper per
QQ-C-576 or ASTM-B-152
(1-332056-0)
Finish
Outer Shell, Center
Conductor—See charts
Ferrule—Tin per MIL-T-10727
Pin Socket
Socket
Selection Chart for Coaxial Cable
Tooling Part No.
Loose Piece Die Inserts for
Cable Size Contact
Contact No.
Ferrule
Hand Tool 69710-1 Hand
(RG/U) Finish
Pin Socket
Part No.
or Pneumatic Tool* Tool
Gold/Nickel
Gold/Copper1 226537-2 51565-2
178, 196 Gold/Nickel 1-332057-0 69690-2 69656-2
Gold/Copper2 — 51565-5
Gold/Nickel
196 Gold/Copper1 226537-2 51565-2
(Double Braid) Gold/Nickel 1-225088-1 — 69656-9
Gold/Copper2 — 51565-5
Gold/Nickel
Gold/Copper1 226537-1 51565-1
174, 188, 316 Gold/Nickel 1-332056-0 69690-2 69656-9
Gold/Copper2 226537-4 51565-4
Gold/Nickel
174 Gold/Copper1 226537-1 51565-1
(Double Braid) Gold/Nickel 1-225088-3 — 69656-7
Gold/Copper2 226537-4 51565-4
Gold/Nickel
Gold/Copper1 226537-1 51565-1
179, 187 Gold/Nickel 1-332056-0 69690-1 354940-1
Gold/Copper2 226537-4 51565-4 & 91911-4
Gold/Nickel
187 Gold/Copper1 226537-1 51565-1
(Double Braid) Gold/Nickel 1-225088-1 — 69656-8
Gold/Copper2 226537-4 51565-4
Gold/Nickel
Gold/Copper1 226537-1 51565-1
161 Gold/Nickel 1-332056-0 — —
Gold/Copper2 226537-4 51565-4
* Use hand actuated Power Unit Part No. 189721-2 or foot actuated Power Unit Part No. 189722-2. Both units
require “C” Head Die Set Adapter Part No. 318161-1 and an Adapter Holder Part No. 356304-1 (with ratchet) or
Part No. 189928-1 (without ratchet). Request Catalog 124208 for more information on the 626 Pneumatic Tool
System.
Extraction Tool Part No. 305183
1.010
[25.65] Ref.
.650
[16.51] Ref.
.250
[6.35]
.112±.005
[2.845±.127]
Dia.
.084
.086
[2.134]
[2.184]
Dia.
.235
[5.969] Max.
0.107 +.005
–.000
[2.718
+.127 ]
–.000
A ±.003
±.076
Dia.
Dia.
Ferrule
Part No. 225088-1—
Part No. 225088-3—
A .120
[3.05] Dia.
A .123
[3.12] Dia.
Ferrule
Part No. 1-332057-0
.111
±.003
[2.82
±.076] Dia.
.250 ±.008
[6.35 ±.203]
Pin
Ferrule
Part No. 1-332056-0
Coaxial Contacts
AMP M Series
Pin and Socket Connectors
40
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Coaxial Contacts (Continued)
Subminiature, Crimp,
Snap-In, Size 16
(Continued)
Selection Chart for Twisted Pair and Shielded Wire
1 000030 [0.00076] gold over .000050 [0.00127] nickel—outer shell and socket center conductor;
.000030 [0.00076] gold over .000100 [0.00254] copper—pin center conductor.
2 000050 [0.00127] gold over .000050 [0.00127] nickel—outer shell and socket center conductor;
.000050 [0.00127] gold over .000100 [0.00254] copper—pin center conductor.
* Use hand actuated Power Unit Part No. 189721-2 or foot actuated Power Unit Part No. 189722-2. Both
units require “C” Head Die Set Adapter Part No. 318161-1 and an Adapter Holder Part No. 356304-1
(with ratchet) or Part No. 189928-1 (without ratchet). Request Catalog 124208 for more information on
the 626 Pneumatic Tool System.
Note: A ferrule is required for each pin and socket.
Extraction Tool Part No. 305183
Tooling Part No.
Wire Size Contact Loose Piece Ferrule Die Inserts for
AWG [mm2] Finish Contact No. Part No. Hand Tool 69710-1 Hand
Pin Socket or Pneumatic Tool* Tool
30 0.05 Gold/Nickel
(Twisted Pair, Solid) Gold/Copper1 226537-3 51565-3 1-332057-0 69690-2 69656-2
28 0.08-0.09 Gold/Nickel
(Twisted Pair, Solid) Gold/Copper1 226537-3 51565-3 1-332057-0 69690 69656
28 0.08-0.09
Gold/Nickel (Twisted Pair,
Gold/Copper
1 226537-3 51565-3 1-332057-0
69690-1 354940-1 & 91911-4
Stranded 7 Str., or or
.0050 [0.13] Dia.) 69690-2 69656-2
26 0.12-0.15
(Twisted Pair, Solid Gold/Nickel1 226537-3 51565-3 1-332057-0 69690 69656
or Stranded 7 Str. Gold/Copper
.0063 [0.16] Dia.)
26 0.12-0.15 Gold/Nickel
(Shielded, .075 [1.91] Gold/Copper1 226537-1 51565-1
Max. O.D.) Gold/Nickel 1-332057-0 69690-3 69656-3
Gold/Copper2 226537-4 51565-4
Coaxial Contacts
41
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Coaxial Contacts (Continued)
Ferrule
Pin
Socket
Ferrule
Miniature, Crimp,
Snap-In, Size 12
.231
[ 5.87 ] Ref. Dia.
.865
[21.97] Ref.
.171±.005
[4.35±0.127] Dia.
.005
[0.127]
Max.
.199
[5.05] Dia.
.425
[10.80] Ref.
Material
Outer Shell - Brass per
MIL-C-50
Center Conductor - Brass per
QQ-B-626
Inner Dielectric -
Polymethylpentene
Retention Spring - Beryllium
copper per QQ-C-533
Ferrule - Copper per QQ-C-576
Finish
Outer Shell, Center Conductor
- See charts on next page
Retention Spring - Nickel per
QQ-N-290
Ferrule - Tin per MIL-T-10727
Extraction Tool Part No.
305183-8
Retention Spring
Part No. 201142-1
Socket
.226
[5.75] Ref. Dia.
Over Sleeve
1.118
[28.4] Ref.
Pin
.040±.002
[1.02±0.05]
Dust Cap
.199
[5.05] Dia.
Coaxial Contacts
AMP M Series
Pin and Socket Connectors
42
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Selection Chart for Shielded Wire
Tooling Part No.
Loose Piece Die Inserts for
Shielded Wire
Contact
Contact No.
Ferrule
Hand Tool 69710-1 Hand
AWG No.
Finish
Pin Socket
Part No.
or Pneumatic Tool* Tool
22 NAS-702, Class A 354940-1
22 MIL-C-7078A, Type II Gold/Nickel1 — 201144-3 328666 69227-2 & 91912-3
Gold/Nickel1 201145-4 201146-4
22 NAS-702, Class B Gold/Copper2 — 201146-9 328663 69220-2 45740-2
Selection Chart for Various Manufacturers’ Cables
Tooling Part No.
Loose Piece Die Inserts for
Cable Size
Dielectric Cable
Braid
Contact
Contact No.
Ferrule
Hand Tool 69710-1 Hand
Type/AWG [mm2]
O.D. (Max.) O.D. Range
Finish
Pin Socket
Part No.
or Pneumatic Tool* Tool
Brand-Rex .076 .112-.122
T209A 0.08 Single Gold/Nickel1 1-— 1-201146-6 330587 — —
29 AWG 1.93 2.84-3.10
Brand-Rex .106 .160
Gold/Nickel1 1-201145-2 1-201146-2
T5788A 0.12-0.15 Single 328664 69222-2 45639-2
26 AWG 2.69 4.06
Gold/Copper2 1-201145-0 1-201146-0
RAYCHEM
0030D1314 .129 .122-.137
Army Ord. 0.03-0.15 Single Gold/Nickel1 1-— 1-201146-6 330587 — —
11207177 3.28 3.10-3.48
32-26 AWG
1.000030 [0.00076] gold over .000030 [0.00076] nickel.
2.000100 [0.00254] gold over .000100 [0.00254] copper.
* Use hand actuated Power Unit Part No. 189721-2 or foot actuated Power Unit Part No. 189722-2. Both units require “C” Head Die Set Adapter
Part No. 318161-1 and an Adapter Holder Part No. 356304-1 (with ratchet) or Part No. 189928-1 (without ratchet). Request Catalog 124208 for
more information on the 626 Pneumatic Tool System.
Note: A ferrule and retention spring (201142-2) are required for each pin and socket.
Selection Chart for Coaxial Cable
Tooling Part No.
Loose Piece Die Inserts for
Cable Size Contact
Contact No.
Ferrule
Hand Tool 69710-1 Hand
(RG/U) Finish
Pin Socket
Part No.
or Pneumatic Tool* Tool
55, 55A, 55B Gold/Nickel1 201145-4 201146-4
141, 142, 223 Gold/Copper2 — 201146-9 330478 69315-4 69248-4
Gold/Nickel1 201145-4 201146-4
58, 58A, 58B, 58C Gold/Copper2 — 201146-9 328663 69220-2 45740-2
174, 179A, 187, Gold/Nickel1 201143-1 201144-1 354940-1
21-598 Gold/Copper2 — 201144-6 328666 69227-2 & 91912-3
180, 180A, 195, Gold/Nickel1 201145-2 201146-2
21-597 Gold/Copper2 1-201145-0 1-201146-0 328664 69222-2 45639-2
178, 178A, 196 Gold/Nickel1 201511-1 201512-1 328667 69373-2 69186-2
Gold/Nickel1 201143-5 201144-5 354940-1
188 Gold/Copper2 201143-7 201144-7 328666 69227-2 & 91912-4
122 Gold/Nickel1 201145-1 — 328664 69222-2 45639-2
188 Double Braid Gold/Nickel1 201143-5 201144-5
316 Double Braid Gold/Copper2 201143-7 201144-7 3-221848-3 — 58290-1
Special .125, .100,
.066, .012DB Gold/Nickel1 201143-1 201144-1 3-221848-3 — 58290-1
Selection Chart for Twisted Pair
Max. Tooling Part No.
Ins. Dia. Contact Loose Piece Ferrule Die Inserts for
Wire Size
(Two Wires Finish Contact No. Part No. Hand Tool 69710-1 Hand
AWG [mm2] Combined) Pin Socket or Pneumatic Tool* Tool
28-26 0.08-0.15 .080 345940-1
(Solid) 2.03 Gold/Nickel1 201511-1 201512-1 328667 69373-2
& 91912-3
24-22 0.2-0.4 .115 Gold/Nickel1 201143-5 201144-5
(Stranded) 2.92 Gold/Copper2 201143-7 201144-7 328666 69672-2 45638-3
24-22 0.2-0.4 .160
(Solid or Stranded) 4.06 Gold/Nickel1 250079-1 250080-1 329029 69222-2 45639-2
Miniature, Crimp,
Snap-In, Size 12
(Continued)
Coaxial Contacts (Continued)
Coaxial Contacts
43
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Engineering Notes
Engineering Notes
AMP M Series
Pin and Socket Connectors
44
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings
Standard connectors are
furnished as unloaded
housings that have
Multimate contact cavities
for accepting Type II, Type
III+, and subminiature
COAXICON crimp-type
contacts, as well as Type
III+ solder-type and
posted contacts. All
Multimate contacts are
interchangeable in the
same housing cavity.
Standard connector hous-
ings are available in sizes
ranging from 6 thru 160
positions. They mate with
each other, as well as
posted connectors of a
corresponding size for
hand tool and semiauto-
matic machine wiring. See
Posted Connector section.
Standard Housings
45
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings (Continued)
6 Position
14 Position
20 Position
Recommended Panel Cutout
Recommended Panel Cutout
Recommended Panel Cutout
.054
[1.37]
.412
[10.46]
.206
[5.23]
.380
[9.65]
.120 Dia.
[3.05]
.915
[23.24]
Typ.
1.00±.020
[25.40±0.51]
.365
[9.27]
Typ. .093
[2.36]
4 Plc.
.688
[17.48]
.580
[14.73]
.016
[0.41] R. Typ.
.130
[3.30] Dia.
.054
[1.37]
.472
[11.99]
.236
[5.99]
.937
[23.8]
.829
[21.06]
.016
[0.41] R. Typ.
.130
[3.30] Dia.
.054
[1.37]
.472
[11.99]
.236
[5.99]
1.250
[31.75]
1.142
[29.01]
.016
[0.41] R. Typ.
.130
[3.30] Dia.
.220±.005
[5.59±0.13]
.120
[3.08]
Dia.
2 Holes
.365
[9.27]
.300
[7.62]
.168
[4.27]
Ref.
.133
[3.38]
.129
[3.28]
Dia.
.915
[23.24]
.130
[3.30]
Typ.
.075
[1.91]
Typ.
Plug Housing
Phenolic Part No. 201355-1
Receptacle Housing
Phenolic Part No. 201298-1
Diallyl Phthalate Part No. 201298-3
.093 R
[2.36]
1.110±.010
[28.19±0.25]
Plug Housing
Phenolic Part No. 201356-1
Diallyl Phthalate Part No.
201356-3
Receptacle Housing
Phenolic Part No. 200346-2
Diallyl Phthalate Part No.
200346-4
Notes: 1. All housings accept Type II, Type III+, and Subminiature COAXICON contacts.
2. Pins and/or sockets may be used in any housing.
3. Dimensions are ±.005 [0.127], unless otherwise noted.
4. Housing cavity identification are mirror image.
Plug Housing
Phenolic Part No. 202758-1
Diallyl Phthalate Part No. 202758-3
Receptacle Housing
Phenolic Part No. 202757-1
Diallyl Phthalate Part No. 202757-3
.187±.015
[4.75±0.38]
.131±.002 Dia.
[3.33±0.05]
Typ.
.548±.010
[13.92±0.25]
2 Holes
R
.440±.010
[11.18±0.25]
.150
[3.81]
Typ.
1.250±.020
[31.75±0.51]
.440±.010
[11.18±0.25]
1.560±.020
[39.62±0.51]
.915
[23.24]
.300
[7.62]
.688
[17.48]
.937
[23.80]
1.250
[31.75]
Standard Housings
AMP M Series
Pin and Socket Connectors
46
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
26 Position
Recommended Panel Cutout
34 Position
Recommended Panel Cutout
.592
[15.04]
A
.118
[3.00]
.790
[20.01] .161
[4.09]
.468
[11.89]
.130 [3.3] Dia.
or
.218 [5.54] Dia.
is required when
jackscrews are
used.
1.450
[36.83]
1.112
[28.24]
.100
[2.54]
.560±.010
[14.22±0.25]
1.630±.020
[41.40±0.51]
.365
[9.27]
.915
[23.24] .750±.010
[19.05±0.25]
2.000±.020
[50.80±0.51]
.468
[11.89]
.365
[9.27]
2 Plc.
.296
[7.52]
.016
[0.41] R. Typ.
.016
[0.41] R.Typ.
.130
[3.30] Dia.
.130
[3.30] Dia.
(4 Holes)
.915
[23.24]
.075
[1.91]
Typ.
.150
[3.81]
Typ.
.130
[3.30]
Typ.
.131
[3.33]
.129
[3.28] B
.131
[3.33]
.129
[3.28]
B
36 Position
Recommended Panel Cutout
.177
[4.48]
.790
[20.07]
.411
[10.43]
.468
[11.89]
2.025
[51.43] A
.128
[3.25]
.915
[23.24]
.780
[19.81]
2.595±.020
[65.91±0.51]
1.983±.010
[50.37±0.25]
2.281
[57.94]
.468
[11.89]
.365
[9.27]
2 Plc.
.010
[0.25]
Typ.
.016
[0.41] R.Typ.
.130
[3.30] Dia.
(4 Holes)
R
Plug Housing (Shown)
Plug Housing (Shown)
Plug Housing (Shown)
A
Standard Housings (Continued)
Standard Housings
47
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
41 Position
26, 34 and 36 Positions
(Continued)
Related Product Data
Dimensions—Page 46
Recommended Panel Cutout
50 Position
Recommended Panel Cutout
Plug Housing
Phenolic Part No. 202135-2
Diallyl Phthalate Part No. 202135-4
Receptacle Housing
Phenolic Part No. 201302-1
Diallyl Phthalate Part No. 201302-3
Plug Housing
Phenolic Part No. 201358-1
Diallyl Phthalate Part No. 201358-3
Receptacle Housing
Phenolic Part No. 200277-2
Diallyl Phthalate Part No. 200277-4
.550
[13.97]
2.322
[58.98]
.128
[3.25]
.790
[20.01]
.161
[4.09]
.395
[10.03]
.468
[11.89]
.130 [3.3] Dia.
or
.218 [5.54] Dia.
is required when
jackscrews are
used.
2.281
[57.94]
2.025
[51.44]
2.200
[55.88]
.061
[1.55]
.915
[23.24]
.240±.020
[6.10±0.51]
.120
[3.05]
Dia.
2.312
[58.72]
.440±.010
[11.18±0.25]
2.687±.020
[68.25±0.51]
.365
[9.27]
.915
[23.24]
.750±.010
[19.05±0.25]
.133
[3.38]
.129
[3.28]
Dia.
2.593±.020
[65.91±0.51]
.275
[6.99]
.016
[0.41] R. Typ.
.016
[0.41] R. Typ.
.130
[3.30] Dia.
.130
[3.30] Dia.
(4 Holes)
.365
[9.27]
Notes: 1. All housings accept Type II, Type III+, and Subminiature COAXICON contacts.
2. Pins and/or sockets may be used in any housing, except for 213800-2, which accepts only pin
contacts.
3. Dimensions are ±.005 [0.127], unless otherwise noted.
4. Housing cavity identification are mirror image.
No. of Housing Plug Dimension Receptacle Dimension
Pos. Material Part Number A Part Number B
Phenolic 201359-1 1.312 200512-2 1.312
33.32 33.32
26
Diallyl 201359-3 1.322 200512-3 1.322
Phthalate 33.58 33.58
Phenolic 1-201357-1 200838-2
213799-1 (Modified) 1.686 213801-1 (Modified) 1.686
34 Polyester 213800-1 42.82 213802-1 42.82
213800-2 (Pins only) —
Diallyl 201357-3 1.696 200838-3 1.696
Phthalate 43.08 43.08
36 Phenolic 203956-2 2.281 — —
57.94
.133
[3.38]
.129
[3.28]
Dia.
Standard Housings (Continued)
2.281+.015
-.005
[57.94+0.38
-0.13]
.750±.010
[19.05±0.25]
Standard Housings
AMP M Series
Pin and Socket Connectors
48
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings (Continued)
Plug Housing
Phenolic Part No. 205058-2
(Mating face contact cavities numbered right to left.)
Plug Housing
Phenolic Part No. 203622-2
(Mating face contact cavities numbered left to right.)
50 Position
Recommended Panel Cutout
2.281
[57.94]
Mating
Face
.140
[3.56]
Typ.
2.025
[51.44]
Typ.
.128
[3.25]
Typ.
.195
[4.95]
Typ.
.766
[19.46]
Typ.
1.155
[29.34]
.500
[12.70]
Typ.
.327
[8.31]
Typ.
.915
[23.24]
2.595±.010
[65.91±0.25]
2.281±.008
[57.94±0.20]
.766±.008
[19.46±0.20]
.011±.001
[0.28±0.03]
.365
[9.27]
Typ.
1.983
[50.37]
Typ.
.016
[0.41] R.Typ.
50 Position
Recommended Panel Cutout
2.281
[57.94]
.140
[3.56]
Typ.
2.025
[51.44]
Typ.
.128
[3.25]
Typ.
.195
[4.95]
Typ.
.766
[19.46]
Typ.
1.155
[29.34]
.500
[12.70]
Typ.
.327
[8.31]
Typ.
.915
[23.24]
1.110±.010
[28.19±0.25]
2.595±.010
[65.91±0.25]
.766±.008
[19.46±0.20]
.365
[9.27]
Typ.
.011±.001
[0.28±0.03]
Typ.
1.983
[50.37]
.016
[0.41] R.Typ.
.156±.005
[3.96±0.13] Dia.
Typ.
.156±.005
[3.96±0.13] Dia.
Typ.
2.281±.008
[57.94±0.20]
Mating
Face
1.110±.010
[28.19±0.25]
Standard Housings
49
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings (Continued)
75 Position
104 Position
Recommended Panel Cutout
Recommended Panel Cutout
Plug Housing
Phenolic Part No. 201310-1
Diallyl Phthalate Part No. 201310-3
Receptacle Housing
Phenolic Part No. 201311-1
Diallyl Phthalate Part No. 201311-3
Plug Housing
Phenolic Part No. 201345-1
Receptacle Housing
Phenolic Part No. 201037-1
.327
[8.31]
2.281
[57.94]
1.580
[40.13]
.790
[20.07] .438
[11.13]
2.375
[60.32]
2.165
[54.99]
.353
[8.97]
.875
[22.22]
.130 [3.30] Dia.
or
.218 [5.54] Dia.†
.105
[2.67]
2.025
[51.44]
.128
[3.25]
.195
[4.95]
.766
[19.46]
1.155
[29.34]
.140
[3.56]
.915
[23.24]
.120
[3.05]
Dia.
2.595±.020
[65.91±0.51]
.365
[9.27]
.766
[19.46]
1.110±.010
[28.19±0.25]
.915
[23.24]
2.750±.010
[69.85±0.25]
.365
[9.27]
.500
[12.70]
.016
[0.41] R.
.016
[0.41] R. Typ.
.156
[3.96] Dia.
(4 Holes)
.156
[3.96] Dia.
(4 Holes)
† .218 [5.54] diameter is required
when jackscrews are used.
.133
[3.38]
.129
[3.28]
Dia.
.375±.015
[9.53±0.38] R. Typ.
Notes: 1. All housings accept Type II, Type III+, and Subminiature COAXICON contacts.
2. Pins and/or sockets may be used in any housing.
3. Dimensions are ±.005 [0.127], unless otherwise noted.
4. Housing cavity identification are mirror image.
2.281
[57.94]
2.375
[60.32]
.133
[3.38]
.129
[3.28]
Dia.
1.527±.010
[38.79±0.25]
Standard Housings
AMP M Series
Pin and Socket Connectors
50
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings (Continued)
104 CF Position
(with Center Fastener)
Recommended Panel Cutout
2.875
[73.02]
2.500
[63.5]
2.188
[55.58]
2.940
[74.68]
2.960
[75.18]
.350±.020
[8.89±0.51]
(Deep from
Back Face)
1/4-26UNF-2B
.500
[12.70]
.812
[20.62]
.172
[4.37] R. Typ.
.143
[3.63] Dia.
(4 Holes)
Plug Housing
Receptacle Housing
Center Fastener
Plug Housing Part No. Receptacle Housing Part No.
Description Length Phenolic Diallyl Polyester Phenolic Diallyl Polyester
Phthalate Phthalate
2.500
“T” Handle 63.50 201692-4 201692-3 1-201692-6
2.500
Slotted Hex 63.50 201692-6 — — 201532-4 201532-2 —
.531
Slotted Hex 13.49 201692-2 — —
1.172
[29.77]
1.245
[31.62]
1.265
[32.13]
.895
[22.73]
.935
[23.75]
.133
[3.38]
.129
[3.28]
Dia.
Notes: 1. All housings accept Type II, Type III+, and Subminiature COAXICON contacts.
2. Pins and/or sockets may be used in any housing.
3. Dimensions are ±.005 [0.127], unless otherwise noted.
4. Housing cavity identification are mirror image.
2.500
[63.50]
.812
[20.62]
Typ.
.130
[3.30]
Typ.
.175
[4.44]
Typ.
.075
[1.31]
Typ.
.150
[3.81]
Typ.
1.130±.010
[28.70±0.25]
2.50
[63.50]
Typ.
.165
[4.19]
Typ.
2.83±.010
[71.86±0.25]
1.250
[31.75]
Typ.
.812
[20.62]
.230±.005
[5.84±0.13]
.531
[13.49]
2.500
[63.50]
.281
[7.14]
Dia.
.150±.005
[3.81±0.13]
.915±.020
[23.24±0.51]
Standard Housings
51
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Standard Housings (Continued)
160 CF Position
(with Center Fastener)
Recommended Panel Cutout
2.795
[70.99]
2.095
[53.21]
.365
[9.27]
Typ.
.365
[9.27]
Typ.
.165
[4.19]
Ref.
4.156
[105.56]
Ref.
1.867
[47.42]
.125
[3.18] R. Typ.
.155
[3.94] Dia.
(4 Holes)
1.174
[29.82]
.500
[12.70]
2.374
[60.30]
2.374±.010
[60.30±0.25]
Typ.
2.374±.010
[60.30±0.25]
Typ.
.915
[23.24]
.915
[23.24]
1.826±.010
[46.38±0.25]
1.826±.010
[46.38±0.25]
2.750±.010
[69.85±0.25]
2.750±.010
[69.85±0.25]
Plug Housing
Phenolic Part No. 202799-2
Diallyl Phthalate Part No. 202799-1
Receptacle Housing
Phenolic Part No. 202800-2
Diallyl Phthalate Part No. 202800-1
Notes: 1. All housings accept Type II, Type III+, and Subminiature COAXICON contacts.
2. Pins and/or sockets may be used in any housing.
3. Dimensions are ±.005 [0.127].
4. Housing cavity identification are mirror image.
.010
[0.25]
.012
[0.31]
Typ.
Standard Housings
AMP M Series
Pin and Socket Connectors
52
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors
Posted connectors are
furnished preloaded with
Size 16, posted contacts
(as shown on page 32)
and are specifically
designed to be wired with
hand tools and semiauto-
matic machines. The
cavity centerline spacing
is too close to accommo-
date the heads and
mandrels of fully auto-
matic machines. Post
configurations of the pre-
loaded contacts are
available for accepting
TERMI-POINT Clip and
wrap-type terminations.
Posted connector hous-
ings are made of black
phenolic or diallyl phtha-
late and are available in
sizes ranging from 6 thru
104 positions. They will
mate with correspond-
ingly sized standard
connector (except .200
[5.08] grid) housings
loaded with Size 16 crimp-
type contacts. It is not
recommended to mate
two posted connectors.
Since the preloaded
posted contacts are rigid
in the housing, mating
two posted connectors,
particularly of the larger
sizes, would be difficult.
Posted connectors can
be substituted for stan-
dard connectors in the
Connector/ Hardware
Selection Charts, pages 10
to 25.
Tyco Electronics does not recommend
the use of shields or strain relief clamps
with posted connectors because of the
potential of shorting.
Posted Connectors
53
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors (Continued)
6 Position
Recommended Panel Cutout
.054
[1.37]
.688
[17.48]
.206
[5.23]
.412
[10.46]
.130
[3.30] Dia.
.016
[0.41] R.
Typ.
14 Position
Recommended Panel Cutout
.054
[1.37]
.937
[23.80]
.236
[5.99]
.472
[11.99]
.130
[3.30] Dia.
.016
[0.41] R.
Typ.
20 Position
Recommended Panel Cutout
.054
[1.37]
1.250
[31.75]
1.142
[29.01]
.236
[5.99]
.472
[11.99]
.130
[3.30] Dia.
.016
[0.41] R. Typ.
.258
[6.55]
Typ.
1.250±.020
[31.75±0.51]
.300
[7.62]
2 Plc. .915
[23.24]
.915
[23.24]
A
A
Plug Assembly Receptacle Assembly
.258
[6.55]
Typ.
.390
[7.62]
2 Plc.
1.560±.020
[39.62±0.51]
Plug Assembly
.580
[14.73]
.440±.010
[11.18±0.25]
.829
[21.06]
.365
[9.27]
1.000±.020
[25.40±0.51]
.915
[23.24]
Plug Assembly
A
Posted Connectors
AMP M Series
Pin and Socket Connectors
54
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors (Continued)
26 Position
Recommended Panel Cutout Plug Assembly
Receptacle Assembly
.592
[15.04]
1.312
[33.32]
1.112
[28.24]
.100
[2.54] .915
[23.24]
.560±.010
[14.22±0.25]
1.630±.020
[41.40±0.51]
.300
[7.62]
Typ.
.296
[7.52]
.016
[0.41] R. Typ.
.130
[3.30] Dia.
Plug and Receptacle Assemblies
No. of Termination Post A Contact Plug Assembly Receptacle Assembly
Pos. Method Configuration Dimension Finish Part No. Part No.
.025 x .025 .659 Sel.
6 Wrap Type 0.64 x 0.64 16.74 Gold/Nickel1 205507-1 —
.659
.025 x .025 16.74 Sel. 205317-1 —
14 Wrap Type 0.64 x 0.64 .261 Gold/Nickel1
6.63 — 3-205508-1
.025 x .025 .659 Sel.
20 Wrap Type 0.64 x 0.64 16.74 Gold/Nickel1 205509-1 —
26 TERMI-POINT .031 x .062 .810 Sel.
Clip 0.79 x 1.57 20.57 Gold/Nickel1 1-205512-3 1-205511-3
1 Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance
of .200 [5.08] from mating end. Posts are plated tin-lead over copper.
Notes: 1. Posted connectors listed above have black phenolic housings.
2. Replacement contacts are shown on page 32.
3. These posted connectors mate with standard connector housings shown on pages 45-47.
.560±.010
[14.22±0.25]
.915
[23.24]
.300
[7.62]
Typ.
1.630±.020
[41.40±0.51]
A
A
Posted Connectors
55
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors (Continued)
34 Position
Recommended Panel Cutout
Plug Assembly
Receptacle Assembly
† .218 [5.54] diameter is required
when jackscrews are used.
.161
[4.09]
Typ.
.790
[20.07]
2.000±.020
[50.80±0.51]
.468
[11.89]
Typ.
.130+.005
-.000
3.30+0.13
-.000
Typ.
.016
[0.41] R
Typ. .915
[23.24]
]
[
.218+.005
-.000
5.54+0.13
-.000
]
[
.130+.005
-.000
3.30+0.13
-.000
4 Holes
]
[
Dia.
1.686
[42.84]
.118
[3.00]
Typ.
.395
[10.03]
.468
[11.89]
.075
[1.91]
Typ.
.150
[3.81]
Typ.
1.687
[42.85]
.915
[23.24]
A
A
.365
[9.27]
2 Plc.
.750±.010
[19.05±0.25]
.750±.010
[19.05±0.25]
.365
[9.27]
.468
[11.89]
2.000±.020
[50.80±0.51]
.275
[6.99]
Typ.
or
†
Posted Connectors
AMP M Series
Pin and Socket Connectors
56
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
50 Position
Recommended Panel Cutout
.161
[4.09]
.790
[20.01] .395
[10.03]
2.593±.020
[65.86±0.51]
.750±.010
[19.05±0.25]
.915
[23.24]
.128
[3.25]
2.025
[51.44]
.468
[11.89] .130 [3.30] Dia.
or
.218 [5.54] Dia.†
2.281
[57.94]
.016
[0.41] R
Typ.
.130
[3.30] Dia.
(4 Holes)
Plug Assembly
† .218 [5.54] diameter is required
when jackscrews are used.
Plug and Receptacle Assemblies
No. of Termination Post A Contact Plug Assembly Receptacle Assembly
Pos. Method Configuration Dimension Finish Part No. Part No.
.659 Sel. Gold/Nickel1 205361-1 3-205505-1
.025 x .025 16.74
34 Wrap Type 0.64 x 0.64 .261
6.63 Sel. Gold/Nickel1 — 3-205505-1
.659
.025 x .025 16.74 Sel. Gold/Nickel1 205156-1 3-205514-1
50 Wrap Type 0.64 x 0.64 .261
6.63 Sel. Gold/Nickel1 — 3-205514-1
1 Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance
of .200 [5.08] from mating end. Posts are plated tin-lead over copper.
Notes: 1. Posted connectors listed above have black phenolic housings.
2. Replacement contacts are shown on page 32.
3. These posted connectors mate with standard connector housings shown on pages 46-47.
.250
[6.35]
4 Plc.
2.595±.020
[65.91±0.51]
.750±.010
[19.05±0.25]
.915
[23.24]
Receptacle Assembly
A
A
Posted Connectors (Continued)
Posted Connectors
57
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
75 Position
Recommended Panel Cutout
.500
[12.70]
2.025
[51.44]
.140
[3.56]
2.281
[57.94]
.327
[8.31]
.016
[0.41] R.
Typ.
.156
[3.96] Dia.
(4 Holes)
104 Position
Recommended Panel Cutout
Receptacle Assembly
† .218 [5.54] diameter is required
when jackscrews are used.
Receptacle Assemblies
No. of Termination Post A Contact Receptacle Assembly
Pos. Method Configuration Dimension Finish Part No.
.025 x .025 .659
75 Wrap-Type 0.64 x 0.64 16.74 Sel. Gold/Nickel1 205515-1
.025 x .025 .659
104 Wrap-Type 0.64 x 0.64 16.74 Sel. Gold/Nickel1 205359-1
1 Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance
of .200 [5.08] from mating end. Posts are plated tin-lead over copper.
Notes: 1. Posted connectors listed above have black phenolic housings.
2. Replacement contacts are shown on page 32.
3. These posted connectors mate with standard connector housings shown on page 49.
.875
[22.22]
.790
[20.01]
.438
[11.13]
.300
[7.62]
2 Plc.
2.750±.010
[69.85±0.25]
2.750±.010
[69.85±0.25]
.915
[23.24]
.105
[2.67]
2.165
[54.99]
.353
[8.97]
.130 [3.30] Dia.
or
.218 [5.54] Dia.†
.016
[0.41] R.
Typ.
.156
[3.96] Dia.
(4 Holes)
2.375
[60.32]
1.580
[40.13]
Receptacle Assembly
.766
[19.46]
.766
[19.46]
.218±.015
[5.54±0.38]
Typ.
.915
[23.24]
1.155
[29.34]
.195
[4.95] .365
[9.27]
A
A
1.110±.010
[28.19±0.25]
1.110±.010
[28.19±0.25]
.128
[3.25]
Posted Connectors (Continued)
Posted Connectors
AMP M Series
Pin and Socket Connectors
58
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors with Center Fastener
2.875
[73.02]
.500
[12.70] Typ.
2.500
[63.50]
2.188
[55.58]
.172
[4.37] R. Typ.
.276
±.010
[7.01
±0.25
]
.230
[5.84]
.150
[3.81]
.143
[3.63] Dia.
(4 Holes)
2.950
±.010
[74.93±0.25]
1.250
[31.75]
.365
[9.27]
2.500
±.015
[63.50
±0.03
]
Typ.
.915
[23.24]
2.755±.015
[69.97±0.38]
1.826±.010
[46.38±0.25]
.365
[9.27]
Typ.
2.375±.010
[60.32±0.25]
Typ.
104 CF Position
(with Center Fastener)
104 CF Position
(with Center Insert)
160 CF Position
(with Jackscrew Socket)
Recommended Panel Cutout
1.172
[29.77]
2.875
[73.02]
.500
[12.70]
2.500
[63.50]
2.188
[55.58]
.812
[20.62]
.172
[4.37] R. Typ.
.915
±.020
[23.24
±0.51
]
Receptacle Assembly (With Posted Socket Contacts)
Plug Assembly (With Posted Pin Contacts)
Receptacle Assembly (With Posted Pin Contacts)
.143
[3.63] Dia.
(4 Holes)
2.950±.010
[74.93±0.25]
1.250±.010
[31.75±0.25]
.365
[9.27]
A
A
A
.150
[3.81]
Typ.
1.174
[29.82]
1.172
[29.77]
.812
[20.62]
Posted Connectors
59
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Posted Connectors with Center Fastener (Continued)
Receptacle Assembly
No. of Housing Receptacle Mating Plug
Pos. Termination Post Material A Contact Assembly Assembly
Method Configuration (Color) Dimension Finish Part No. Part No.
.659
Phenolic 16.74 Sel. Gold/Nickel1 205720-2
.025 x .025 (Black) .261
104 CF Wrap-Type 0.64 x 0.64 6.63 Sel. Gold/Nickel1 205720-1
Page 50
Diallyl Phthalate .261
(Blue) 6.63 Sel. Gold/Nickel2 — 213763-1
160 CF Wrap-Type .025 x .025 Diallyl Phthalate .261
0.64 x 0.64 (Blue) 6.63 Sel. Gold/Nickel2 213521-1 202799 (Page 51)
1 Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance of .200 [5.08] from mating end.
Posts are plated tin-lead over copper.
2
Gold flash over .000050 [0.00127] nickel on entire contact, with .000030 [0.00076] gold to a distance of .250 [6.53] from mating end.
Posts are plated tin-lead over copper.
Extraction Tool Part No. 305183.
Note: Replacement contacts (Type III+ posted) are shown on page 32.
Posted Connectors
AMP M Series
Pin and Socket Connectors
60
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
50 Position
Recommended Panel Cutout
Recommended Panel Cutout
2.025
[51.44]
2.281
[57.94]
.766
[19.45]
1.155
[29.33]
.156+.005
-.000
3.96+0.13
-.000
Dia.
4 Holes
.128
[3.25] Typ.
Material and Finish
Housing - Phenolic per
MIL-M-14, Type CFG; color,
black
Contacts - Brass per
MIL-C-50;
selective .000030 [0.00076]
gold over .000050 [0.00127]
nickel plated (gold plating
per MIL-G-45204, nickel plat-
ing per QQ-N-290)
Plug Assemblies
No. of Termination Post Post Contact Plug Assembly Mates with Receptacle Assembly
Pos. Method Configuration Length† Finish Part Number Part Number
36 TERMI-POINT .031 x .062 .810 Sel. Gold/Nickel1 205629-1
n
50 Clip 0.79 x 1.57 20.57 205630-1
1Gold flash over .000050 [0.00127] nickel on entire contact with .000030 [0.00076] gold to a distance of .200 [5.08] from
mating end. Posts are plated tin-lead over copper.
†Post length will accommodate up to 3 terminations.
Extraction Tool-Part No. 305183.
Refer to page 32 for contact specifications (Type III+, Size 16).
m Mating receptacle block using crimp, snap-in contacts for 36-Position Plug Assembly, order Part No. 203956-2.
Mating receptacle block using crimp, snap-in contacts for 50-Position Plug Assembly, order Part No. 203622-2.
Refer to the appropriate column of Application Chart for Hardware Selection Page 10 through Page 25.
Note: 36 position connector uses standard 50 position hardware. 50 position connector uses standard 75 position hardware.
.300
[7.62]
2.595±.020
[65.91±0.51]
.915
[23.24]
.140
[3.56]
Typ.
][
.016
[0.41] R
.195
[4.95]
Typ.
.365
[9.27]
Plug Assembly (With Posted Pin Contacts)
1.110±.010
[28.19±0.25]
.500
[12.70]
Typ.
36 Position
.173
[4.39]
2.025
[51.44]
2.281
[57.94]
.407
[10.34]
.815
[20.70]
.016
[0.41] R
4 Plc.
.780
[19.81]
Plug Assembly (With Posted Pin Contacts)
R
.915
[23.24]
.365
[9.27]
.468
[11.89]
.130+.005
-.000
3.30+0.13
-.000
4 Plc.
]
[
Dia.
.300
[7.62]
2.595±.020
[65.91±0.51]
† .218 [5.54] diameter
is required when jack-
screws are used.
.130+.005
-.000
3.30+0.13
-.000
or
.218+.005
-.000
5.54+0.13
-.000
]
]
[
[
†
Posted Connectors, .200 [5.08] Grid
.327
[8.31]
Typ.
Posted Connectors
61
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application
Connectors are available in
the following configurations:
V.35
Shallow Block
High Current
Mixed
High Voltage
RFI/EMI Shielded
Grounding Blocks
V.35 Connector
The 34 position V.35
Connector is fully assembled
and ready for placement on a
printed circuit board. They are
also available in kit form for
cable assembly. These
AMP V.35 connectors meet
the requirements of 408-2593
for CCITT V.35 interfacing.
High current connectors are
designed for applications
requiring up to 25 amperes of
current. They are available in
12-position male and female
housings which have rectan-
gular contact cavities for
accepting Type XII contacts.
Mixed connectors are
designed for applications that
require intermixing signal,
power and/or coaxial circuits
in the same connector
housing. Housings are avail-
able in 15-, 16-, 29 CF
(center fastener) and
42-position sizes and,
depending upon the specific
configuration, will accept
Multimate contacts, Type I
and Miniature, Standard and
Twin Standard COAXICON
contacts. The rectangular
contact cavities accept
Type XII contacts.
High voltage connectors are
designed for high voltage
applications using Multimate
contacts. The cavity centerline
spacings and the silo con-
struction of the contact
cavities increase the current
creepage path for higher volt-
age ratings. Housing sizes
include 20 and 28 positions.
RFI/EMI shielding kits
provide shielding capabilities
against radio frequency and
electromagnetic interferences.
Special 104-position housings
accept Multimate contacts
and are especially designed
for use with shielding hard-
ware. These shielding kits
cannot be used with the
standard 104-position
connector housings.
Grounding blocks are
ideally suited for aircraft appli-
cations, where shielded cable
is to be grounded to an air-
frame. The ground wires of
shielded cables are pigtailed
off with ferrules and are
crimped to Size 16 socket con-
tacts. The contacts are loaded
into a standard 14- or 34-posi-
tion connector housing. This
connector then can be mated
to the grounding block which
is fastened to the aircraft
frame. Grounding blocks have
Size 16 screw-machined pin
contacts which are staked, riv-
eted and soldered into the
L-shaped metal bracket. The
bracket has fixed jackscrew
receptacles that will accept
the special turnable jack-
screws fastened to the mating
socket connector half.
Special Application Connectors
Special Application Connectors
AMP M Series
Pin and Socket Connectors
62
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Special Application Connectors
Series connectors.
Cable connector assem-
blies are offered in kit
form. Each kit contains: a
34-position housing; one-
piece or two-piece shield;
two, one-piece turnable
jackscrews; strain relief
clamp; and necessary
mounting screws. Shields
are offered in an economi-
cal one-piece stamped
and formed version or a
more durable two-piece
die cast version. A choice
of die cast zinc, nickel
plated
or stainless steel turnable
jackscrews are available.
Cable connectors accept
Size 16, Type III+ pin and
socket contacts.
(Contacts sold separately,
see page 31.)
AMP M Series V.35 Special
Application Connectors
meet the requirements of
ISO 2593 for CCITT V.35
interface.
Technical Documents
Product Specifications—
108-10001 M Series 042 Type
The 34-position V.35
includes both printed cir-
cuit board mount and
cable mount configura-
tions.
The pcb connectors are
fully assembled and ready
for placement on printed
circuit boards. Available
in vertical or right-angle
mount versions, they offer
dependable, convenient
assembly in high-speed
data transmission applica-
tions. Connectors are
preloaded with economi-
cal, dependable Size 16
precision stamped and
formed contacts. Contact
posts feature a chamfered
lead-in that eases assem-
bly to the pc boards. A
mounting bracket for
securing the connector to
the pc board is standard
equipment. Right-angle
pcb connectors feature
true position, location
wafers that provide for
the exact location of each
post. Both the right-angle
and vertical mount pcb
connectors are fully mate-
able with comparable M
Product Facts
Meets requirements of
408-2593 for CCITT
V.35 interface
Pcb connectors fully
assembled, right-angle
and vertical mount
Mounting bracket
secures pcb connector
to board
Pcb connectors pre-
loaded with Size 16
contacts
Right-angle connector
features true position
location wafer
Intermateable with
comparable M Series
connectors
Cable connector kits
available with 1-piece
stamped and formed
shield or new, more
durable die cast
2-piece shield
Cable connectors
accept Size 16, Type
III+ strip form or loose
piece contacts
Housings made of UL
94V-0 rated flame
retardant material
Recognized under the
Component Program of
the Underwriters
Laboratories
Inc. for 250 volts,
File No. E28476
Certified by Canadian
Standards
Association,
File No. LR7189
Special Application Connectors
63
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Special Application Connectors (Continued)
Material Specifications
Contacts
The material composition and
construction of AMP Type III+
contacts encompasses vary-
ing price ranges and
performance characteristics.
Specific materials and avail-
able plating thicknesses of
each contact are provided.
Housings
M Series V.35 connector
housings are made of
general purpose phenolic
(black) or polyester (black).
Phenolic housings are
molded of material per
MIL-M-14, Type CFG. The per-
formance characteristics of
this material makes the con-
nector an excellent choice in
applications where excep-
tional resistance to acids,
alkalies, or solvents is not a
prime factor.
Hardware
A variety of materials such as
plated steel, stainless steel,
zinc (nickel plated) and alu-
minum are used in the
manufacture of M Series V.35
connector hardware. This
provides for the proper oper-
ation and durability of each
hardware component, while
offering a choice of econo-
mies to satisfy partic-
ular application
requirements.
Performance Data
Temperature Rating -
Phenolic Housings, -55°C to
+150°C
Polyester Housings -
–55°C to +130°C
Flammability Rating -
Phenolic Material, UL 94V-0
Dielectric Withstanding
Voltage (at sea level)
Type III+ Contacts, 900 VAC,
RMS
Durability (Mating/Unmating)
- Contacts, Gold plated -
500 cycles; Contacts, Bright
tin-lead plated - 50 cycles
Note: For detailed information on
the above performance data and
further information on other perfor-
mance data such as Insulation
Resistance, Thermal Shock, Moisture
Resistance, Vibration and Physical
Shock, request AMP Product
Specification No. 108-10001.
Current Carrying
Capabilities
The total current capacity
of each contact in any given
M Series connector is depen-
dent upon the heat rise
resulting from the combina-
tion of electrical loads of all
contacts in the connector
arrangement and the maxi-
mum ambient temperature in
which the connector will be
operating. Caution must be
taken to insure that this com-
bination of conditions does
not cause the internal tem-
perature of the connector to
exceed the maximum operat-
ing temperature of the
housing material. Several vari-
ables which must be
considered when determining
this maximum current capa-
bility for your application are:
a) Wire Size - Larger wire
will carry more current
since it has less internal
resistance to current flow
and generates less heat.
The wire also conducts
heat away from the
connector.
b) Connector Size - In
general, with more
circuits in a connector,
less current per contact
can be carried.
c) Current Load Distribution -
Spreading those lines
with greater current loads
throughout the connector,
particularly around the
outer perimeter, will
enhance heat dissipation.
d) Ambient Temperature -
With higher ambient
temperature, less
current can be carried.
Special Application Connectors
AMP M Series
Pin and Socket Connectors
64
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Printed Circuit Board Connectors
PCB
No. of Mounting Dimensions Housing Part
Pos. Bracket A B
Boardlocks
Material
Select Load Pattern
Number
Brass, .555
34 Tin-Nickel Plated 14.10 * No Polyester Fully Loaded 1-213806-0
34 None — * No Polyester Fully Loaded 1-213806-3
Brass, .555 A, B, C, D, E, F, H, J, L, P,
19 Tin-Nickel Plated 14.10 * No Polyester R, S, T, U, V, W, X, Y, AA Hardware Supplied Unassembled 1-213806-1
None — A, B, C, D, E, F, H, K, P,
18
* — Polyester R, S, T, U, V, W, X, Y, AA No Hardware Supplied 1-213806-2
Zinc, .572 .347
34 Nickel Plated 14.53 8.81 Yes Polyester Fully Loaded 213977-9
Zinc, .572 .347
23 Nickel Plated 14.53 8.81 Yes Polyester A, B, C, D, E, F, H, J, K, L, N, P, R, S, T, U, V, W, X, Y, AA, BB, NN 213977-7
Zinc, .572 .347
23 Nickel Plated 14.53 8.81 Yes Polyester A, B, C, D, E, F, H, J, L, N, P, R, S, T, U, V, W, X, Y, AA, HH, KK, NN 213977-8
Zinc, .572 .347
17 Nickel Plated 14.53 8.81 Yes Polyester A, B, C, D, E, F, H, P, R, S, T, U, V, W, X, Y, AA 1-213807-0
*The mounting bracket has an elongated slot for a 4-40 screw that will accommodate a .330 [8.38] or .347 [8.81] footprint.
Note: Other select loaded configurations can be made available; consult Tyco Electronics Corporation.
Right-Angle
Receptacle Assembly
Material and Finish
Housing—Flame retardant
phenolic or polyester, black
Contacts—Brass, plated:
a) .000030 [0.00076] gold
min. in
mating area, .000050
[0.00127] nickel min. under-
plating overall
Contact Spring—Stainless
steel
Contact Post—Brass, tin
plated
Mounting Bracket—Brass,
tin-nickel plated or zinc,
nickel plated
PCB
No. of Mounting Dimensions Housing Part
Pos. Bracket A B
Boardlocks
Material
Select Load Pattern
Number
.555
34 14.10 * No Phenolic Fully Loaded 2-212810-0
Brass, .555
14 Tin-Nickel 14.10 * No Phenolic B, C, D, E, F, H, P, R, S, T, V, X, Y, AA 2-212810-4
Plated .555 A, B, C, D, E, F, H, J, P, R, S, T, U, V, W, X, Y,
27 14.10 * No Phenolic AA, BB, CC, DD, FF, HH, JJ, KK, LL, NN 2-212810-7
.572 .347
34 14.53 8.81 Yes Phenolic Fully Loaded 1-213574-1
.572 .347
17 14.53 8.81 Yes Phenolic A, B, C, D, E, F, H, P, R, S, T, U, V, W, X, Y, AA 1-213574-2
Zinc, .572 .347 A, B, C, D, E, F, H, J, K, L, N, P, R, S, T, U, V, W, X, Y,
23 Nickel 14.53 8.81 Yes Phenolic AA, BB, NN 1-213574-3
Plated .572 .347
22 14.53 8.81 Yes Phenolic A, B, C, D, E, F, H, K, L, N, P, R, S, T, U, V, W, X, Y, AA, BB, NN 1-213574-4
.555 .330
22 14.10 8.38 Yes Phenolic A, B, C, D, E, F, H, J, L, N, P, R, S, T, U, V, W, X, Y, AA, HH, NN 1-213574-5
2.000±.020
[50.80±0.51]
.750
[19.05]
.375
[9.52]
Ref.
1.565
[39.75]
.275
[6.98]
2 Plc.
.365
[9.27]
2 Plc.
.468
[11.89]
2 Plc.
1.687
[42.85]
(For Recommended PC Board Hole Pattern see page 65)
Boardlocks—Copper alloy, tin
plated
Location Wafer—Phenolic
Nuts and Lockwashers—
Steel, zinc plated
Jackscrews—Stainless steel
Special Application Connectors
65
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Printed Circuit Board Connectors (Continued)
No. of Mounting Dimensions Housing Part
Pos. Bracket A B Boardlocks Material Select Load Pattern Number
Zinc, Nickel .572 .347
34 Plated 14.53 8.81 Yes Polyester Fully Loaded 213808-3
18 — No Hardware Supplied Polyester A, B, C, D, E, F, H, K, P, R, S, T, U, V, W, X, Y, AA 213808-4
Note: Other select loaded configurations can be made available; consult Tyco Electronics Corporation.
Right-Angle Plug
Assembly
Material and Finish
Housing - Flame retardant
phenolic or polyester, black
Contacts—Brass, plated:
a) .000030 [0.00076] gold
min. in mating area, .000050
[0.00127] nickel min. under-
plating overall
Contact Spring - Stainless
steel
Contact Post—Brass, tin
plated
Mounting Bracket - Brass,
tin-nickel plated or zinc,
nickel plated
Boardlocks - Copper alloy, tin
plated
Location WafervPhenolic
Nuts and Lockwashers -
Steel, zinc plated
Jackscrews - Stainless steel
.225
[5.72]
.075
[1.91]
.075
[1.91]
.225
[5.72]
B
A
NN
JJ
DD
Z
V
R
L
F
B
MM
HH
CC
Y
U
P
K
E
A
LL
FF
BB
X
T
N
J
D
KK
EE
AA
W
S
M
H
C
.600
[15.24]
.450
[11.43]
.300
[7.62]
.150
[3.81]
.000
[0.00]
.150
[3.81]
.300
[7.62]
.450
[11.43]
.600
[15.24]
.525
[13.34]
.375
[9.53]
.225
[5.72]
.075
[1.91]
.075
[1.91]
.225
[5.72]
.525
[13.34]
.843
[21.41]
.000
0.00
.125
.005
[3.18
0.13
]
2 Plc. Dia.
.054
.002
[1.37
0.05
]
34 Plc.
Dia.
.843
[21.41]
.375
[9.53]
Recommended PC Board Hole Pattern
(All dimensions typical)
No. of Mounting Dimensions Housing Part
Pos. Bracket A B Boardlocks Material Select Load Pattern Number
Brass, Tin .555
34 Nickel Plated 14.10 * No Phenolic Fully Loaded 213289-2
Zinc, Nickel .572 .347
34 Plated 14.53 8.81 Yes Phenolic Fully Loaded 213513-4
*The mounting bracket has an elongated slot for a 4-40 screw that will accommodate a .330 [8.38] or .347 [8.81] footprint.
Note: Other select loaded configurations can be made available; consult Tyco Electronics Corporation.
2.000±.020
[50.80±0.51]
.750
[19.05]
.375
[9.52]
Typ.
1.565±.020
[39.75±0.51].275
[6.98]
2 Plc.
.468
[11.89]
2 Plc.
1.687
[42.85]
.365
[9.27]
2 Plc.
Note: Pc board layouts and connector dimen-
sions illustrated above serve as a guide only; they
are not to be used for actual design or construc-
tion of customer equipment. Consult AMP
customer drawings for latest detailed pc board
layout and connector dimension requirements.
Special Application Connectors
AMP M Series
Pin and Socket Connectors
66
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Printed Circuit Board Connectors (Continued)
Vertical Receptacle
Assembly
Material and Finish
Housing - Flame retardant
phenolic or polyester, black
Contacts - Brass, plated:
a) .000030 [0.00076] gold
min. in mating area, .000050
[0.00127] nickel min. under-
plating overall
Contact Spring - Stainless
steel
Contact Post - Brass, tin-lead
plated
Nuts and Lockwashers -
Steel, zinc plated
Spacers - Stainless steel
Jackscrews - Stainless steel
Note: Pc board layouts and connector dimen-
sions illustrated above serve as a guide only;
they are not to be used for actual design or
construction of customer equipment. Consult
AMP customer drawings for latest detailed pc
board layout and connector dimension require-
ments.
No. of Mounting Housing Part
Pos. Hardware Material Select Load Pattern Number
None Phenolic Fully Loaded 213473-3
34 Phenolic 213524-8
Spacers Polyester Fully Loaded 213809-7
Nuts &
13 Lockwashers Phenolic B, C, D, E, F, P, R, S, T, V, X, Y, AA 213524-9
Note: Other select loaded configurations can be made available; consult Tyco Electronics Corporation.
.260
[6.60]
.080
[2.03]
.100
[2.54]
.280
[7.11]
B
F
L
R
V
Z
DD
JJ
NN
A
E
K
P
U
Y
CC
HH
MM
D
J
N
T
X
BB
FF
LL
C
H
M
S
W
AA
EE
KK
.600
[15.24]
.450
[11.43]
.300
[7.62]
.150
[3.81]
.000
[0.00]
.150
[3.81]
.300
[7.62]
.450
[11.43]
.600
[15.24]
.525
[13.34]
.375
[9.53]
.225
[5.72]
.075
[1.91]
.075
[1.91]
.225
[5.72]
.525
[13.34]
.843
[21.41]
.125±.005
[3.18±0.13]
2 Plc. Dia.
.054±.002
[1.37±0.05]
34 Plc. Dia.
.843
[21.41]
.375
[9.53]
Recommended PC Board Hole Pattern
(All dimensions typical)
2.000±.020
[50.80±0.51]
.750
[19.05]
.915
[23.24] .468
[11.89]
2 Plc.
1.686
[42.82]
.365
[9.27]
2 Plc.
Special Application Connectors
67
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Printed Circuit Board Connectors (Continued)
Vertical Plug Assembly
Material and Finish
Housing - Flame retardant
phenolic, black
Contacts - Brass, plated:
a) .000030 [0.00076] gold
min. in mating area, .000050
[0.00127] nickel min. under-
plating overall
Contact Spring - Stainless
steel
Contact Post - Brass, tin-lead
plated
Nuts and Lockwashers -
Steel, zinc plated
Spacers - Stainless steel
Jackscrews - Stainless steel
Note: Pc board layouts and connector dimen-
sions illustrated above serve as a guide only;
they are not to be used for actual design or
construction of
customer equipment. Consult Tyco Electronics
customer drawings for latest detailed pc board
layout and connector dimension requirements.
No. of Mounting Part
Pos. Hardware Select Load Pattern Number
19 Spacers* A, B, C, D, E, F, K, L, N, P, R, S, T, U, V, W, X, Y, AA 213550-4
34 Spacers* Fully Loaded 213550-5
*Jackscrews and spacers are provided unassembled.
Note: Other select loaded configurations can be made available, consult Tyco Electronics Corporation.
.260
[6.60]
.080
[2.03]
.100
[2.54]
.280
[7.11]
NN
JJ
DD
Z
V
R
L
F
B
MM
HH
CC
Y
U
P
K
E
A
LL
FF
BB
X
T
N
J
D
KK
EE
AA
W
S
M
H
C
.600
[15.24]
.450
[11.43]
.300
[7.62]
.150
[3.81]
.000
[0.00]
.150
[3.81]
.300
[7.62]
.450
[11.43]
.600
[15.24]
.525
[13.34]
.375
[9.53]
.225
[5.72]
.075
[1.91]
.075
[1.91]
.225
[5.72]
.525
[13.34]
.843
[21.41]
.125±.005
[3.18±0.13]
2 Plc. Dia.
.054±.002
[1.37±0.05]
34 Plc. Dia.
.843
[21.41]
.375
[9.53]
Recommended PC Board Hole Pattern
(All dimensions typical)
2.000±.020
[50.80±0.51]
.750
[19.05]
.915
[23.24]
.468
[11.89]
2 Plc.
1.686
[42.82]
.365
[9.27]
2 Plc.
Special Application Connectors
AMP M Series
Pin and Socket Connectors
68
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Cable Connectors
Cable Connector Kits,
34 Position, Phenolic
Material and Finish
Housing - Flame retardant
phenolic, black
Shield - Anodized aluminum
Screws - Steel, zinc plated
Jackscrews - Stainless steel
Cable Clamp - Steel, nickel
plated
Kits include:
Housing
One-piece shield
One-piece turnable
jackscrews
Strain relief clamp
Mounting screws
Plug
Receptacle
Shield Cable Dia. Housing Dimension Kit Part Numbers
Size Range Material A Receptacle Plug
Short .435-.545 Phenolic 1.53 — 213300-1
11.05-13.83 38.86
Short .300-.450 Phenolic 1.53 — 213300-2
7.62-11.43 38.86
Long .435-.545 Phenolic 1.97 — 213300-3
11.05-13.83 50.04
Long .300-.450 Phenolic 1.97 — 213300-4
7.62-11.43 50.04
Short .435-.545 Phenolic 1.53 213522-1 —
11.05-13.83 38.86
Short .300-.450 Phenolic 1.53 213522-2 —
7.62-11.43 38.86
Short .200-.300 Phenolic 1.53 — 213300-7
5.08-7.62 38.86
2.050±.030
[52.07±0.76]
A ±.040
0
[±1.02]
.828±.030
[21.03±0.76]1.620±.040
[41.15±1.02]
Notes:
1. Plug and receptacle connector kits come partially assembled.
2. Plug connector kits are
available with long and short shields, (long shield provides pin protection) and two differ-
ent size cable clamps.
3. Housings are keyed to fix the proper location of the male and female jackscrew as defined
by 408-2593.
4. Short shield kits, Part No. 213753-1 available with all accessories listed above except hous-
ing block and jackscrews. Part number for blocks are found on page 47.
5. Pin and socket contacts sold separately. Size 16, Type III+ contacts are listed on page 31.
Special Application Connectors
69
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Cable Connectors (Continued)
Packaging Cable Dia. Housing Jackscrew Kit Part Numbers
Range Material Type Receptacle Plug
Bulk .435-.545 Polyester Stainless Steel 213931-1 —
11.05-13.83
Individual .300-.450 Polyester Stainless Steel 213931-2 —
7.62-11.43
Individual .435-.545 Polyester Zinc 213931-3 —
11.05-13.83
Individual .435-.545 * Zinc 213931-4 —
11.05-13.83
Individual .300-.450 Polyester Zinc 213931-5 —
7.64-.11.43
Bulk .435-.545 Polyester Stainless Steel — 213932-1**
11.05-13.83
Individual .300-.450 Polyester Stainless Steel — 213932-2**
7.62-11.43
Individual .435-.545 Polyester Zinc — 213932-3**
11.05-13.83
Individual .300-.450 Polyester Zinc — 213932-4**
7.62-11.43
Individual .300-.450 Polyester Zinc — 213932-5**
7.62-11.43
**Housing not included in Kit No. 213931-4
**Long Shield, Assembled Length – 2.060±.040 [52.32±1.20]
Cable Connector Kits,
34 Position, Polyester
(Continued)
Material and Finish
Housing—Flame retardant
polyester, black
Shield—Anodized aluminum
Screws—Steel, zinc plated
Jackscrews—Stainless steel
or zinc, nickel plated
Cable Clamp—Steel, nickel
plated
Kits include:
Housing
One-piece shield
One-piece turnable
jackscrews
Strain relief clamp
Mounting screws
Plug
Receptacle
2.050±.030
[52.07±0.76]
.828±.030
[21.03±0.76]1.620±.040
[41.15±1.02]
Notes:
1. Plug and receptacle connector kits come partially assembled.
2. Two different size cable clamps.
3. Housings are keyed to fix the proper location of the male and female jackscrew as defined
by 408-2593.
4. Pin and socket contacts sold separately. Size 16, Type III+ contacts are listed on page 31.
Special Application Connectors
AMP M Series
Pin and Socket Connectors
70
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Cable Connectors (Continued)
Cable Connector Kits,
34 Position, Phenolic
(Continued)
Material and Finish
Housing - Flame retardant
phenolic, black
Shield - Zinc, nickel plated
Screws - Steel, zinc plated
Jackscrews - Stainless steel
or zinc, nickel plated
Cable Clamp - Steel, nickel
plated
Kits include:
Housing
Two-piece shield
One-piece turnable
jackscrews
Two cable clamp
inserts
Mounting screws
Notes:
1. Plug and receptacle con-
nector kits come partially
assembled.
2. Plug connector kits are
available with or without
pin hoods.
3. Housings are keyed to fix
the proper location of the
male and female jack-
screw as defined by
408-2593.
4. Choice of stainless steel or
zinc die cast one-piece
jacksrews.
5. Pin and socket contacts
sold separately. Size 16,
Type III+ contacts are
listed on page 31.
Pin Cable Dia. Jackscrew Kit Part Numbers
Hood Range Type Receptacle Plug
No .400-.600
10.16-15.24 Zinc — 213684-1
No .250-.400
6.35-10.16 Zinc — 213684-2
Yes .400-.600
10.16-15.24 Zinc — 213684-3
Yes .250-.400
6.35-10.16 Zinc — 213684-4
No .400-.600
10.16-15.24 Stainless Steel — 213684-7
No .400-.600
10.16-15.24 Zinc 213685-1 —
No .250-.400
6.35-10.16 Zinc 213685-2 —
No .400-.600
10.16-15.24 Stainless Steel 213685-3 —
No .150-.300
3.81-7.62 Zinc 213685-5 —
Yes .150-.300
3.81-7.62 Zinc — 213684-9
No .150-.300
3.81-7.62 Zinc — 1-213684-0
Long Screw (2)
Pin Hood
Short Screw (4) Connector
Housing
Female
Jackscrew
Cable
Clamp
Male
Jackscrew
Two-Piece
Shield
Special Application Connectors
71
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
M Series V.35 Cable Connectors (Continued)
Cable Connector Kits,
34 Position, Polyester
(Continued)
Material and Finish
Housing—Flame retardant
polyester, black
Shield—Zinc, nickel plated
Screws—Steel, zinc plated
Jackscrews—Zinc, nickel
plated
Cable Clamp—Steel, nickel
plated
Kits include:
Housing
Two-piece shield
One-piece turnable
jackscrews
Two cable clamp
inserts
Mounting screws
Notes:
1. Plug and receptacle con-
nector kits come partially
assembled.
2. Plug connector kits are
available with or without
pin hoods.
3. Housings are keyed to fix
the proper location of the
male and female jack-
screw as defined by
408-2593.
4. Pin and socket contacts
sold separately. Size 16,
Type III+ contacts are
listed on page 31.
Pin Cable Dia. Kit Part Numbers
Hood Range Receptacle Plug
No .150-.300
3.81-7.62 — 213803-1
No .250-.400
6.35-10.16 — 213803-2
Yes .150-.300
3.81-7.62 — 213804-1
Yes .250-.400
6.35-10.16 — 213804-2
No .150-.300
3.81-7.62 213805-1 —
No .250-.400
6.35-10.16 213805-2 —
No .400-.600
10.16-15.24 — 213803-3
Yes .400-.600
10.16-15.24 — 213804-3
No .400-.600
10.16-15.24 213805-3 —
Long Screw (2)
Pin Hood
Short Screw (4) Connector
Housing
Female
Jackscrew
Cable
Clamp
Male
Jackscrew
Two-Piece
Shield
Special Application Connectors
AMP M Series
Pin and Socket Connectors
72
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors
High Current 12 Position
UL Voltage Rating:
1800 V
Material and Finish
Housing - Phenolic, 94V-O rated,
black
Contacts must be ordered
separately.
2.025
[51.44]
.500
[12.70]
.016
[0.41] R
Typ.
2.281
[57.94]
.766
[19.46]
.140
[3.56]
.327
[8.31]
1.155
[29.34]
.195
[4.95]
.156
[3.96] Dia.
4 Holes
Recommended Panel Cutout
.365
[9.27]
Typ.
1.983±.010
[50.37±0.25]
2.595±.020
[65.91±0.51]
.120
[3.05]
Dia.
1.110±.010
[28.19±0.25].386
[9.80]
Typ.
.450
[11.43]
Typ.
Plug Housing
Receptacle Housing
Phenolic
Housing Part No. Contacts Accepted
Plug Receptacle Quantity Contact Type Page Ref.
205042-1 205043-1 12 Type XII 38, 39
Note: 12 position connector uses Standard 75 Position Hardware. Refer to appropriate column of
Application Charts for Hardware Selection pages 10 through 25.
1.110±.010
[28.19±0.25]
2.595±.020
[65.91±0.51]
1.983±.010
[50.37±0.25]
.120
[3.05]
Dia.
.365
[9.27]
1.500
[38.10]
2.281
[57.94]
.128
[3.25]
1.090+.020
-.000
27.69+0.51
-.000
[ ]
Special Application Connectors
73
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors (Continued)
Phenolic
Housing Part No. Contacts Accepted
Plug Receptacle Quantity Contact Type Page Ref.
Type II 30
Type III+ 31-35
*14* Subminiature
COAXICON 40, 41
202479-2 202478-2 12 Type XII 38, 39
Standard
2 COAXICON —
Type I 36
1 Miniature
COAXICON 42, 43
*Quantity may be all of the same type, or a combination of those types listed.
See Hardware Section for appropriate hardware for this connector. See pages 78-89.
Mixed 29 CF Position
(with Center Fastener)
Material and Finish
Housing - Phenolic, 94V-O
rated, black
Contacts must be ordered
separately.
.500
[12.70]
.766
[19.46]
.015
[0.38] R
Typ. 2.282
[57.96]
.190
[4.83]
1.147
[29.13]
.200
[5.08]
.128
[3.25]
2.025
[51.44]
.323
[8.20]
.156
[3.96] Dia.
4 Holes
Recommended Panel Cutout
.365
[9.27]
1.440
[36.58]
2.595
[65.91]
2.282
[57.96]
1.110±.010
[28.19±0.25]
Plug Housing
Receptacle Housing
1.110±.010
[28.19±0.25]
2.595±.020
[65.91±0.51]
.213±.015
[5.41±0.38]
.148
[3.76]
.152
[3.86]
.365
[9.27]
1.025
[26.04]
.095
[2.41] R
1.983±.010
[50.37±0.25]
.148
[3.76]
.152
[3.86]
1.983
[50.37]
Dia.
Dia.
Special Application Connectors
AMP M Series
Pin and Socket Connectors
74
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors (Continued)
Phenolic Diallyl Phthalate
Housing Part No. Housing Part No. Contacts Accepted
Plug Receptacle Plug Receptacle Quantity Contact Type Page Ref.
Type II 30
Type III+ 31-35
36* Subminiature
202515-1 202516-1 202515-3 202516-3 COAXICON 40, 41
Type I 36
6* Miniature
COAXICON 42, 43
*Quantity may be all of the same type, or a combination of those types listed.
Note: 42 position connector uses Standard 50 Position Hardware. Refer to appropriate column of
Application Charts for Hardware Selection pages 10 through 25.
.790
[20.01]
.065
[1.65] R
or
.109
[2.77] R†
2.281
[57.94]
.395
[10.03]
.161
[4.09]
.130
[3.30] Dia.
4 Holes
.128
[3.25]
†.218 [5.54] diameter is required
when jackscrews are used.
2.025
[51.44]
.468
[11.89]
Recommended Panel Cutout Plug Housing Receptacle Housing
.750±.010
[19.05±0.25]
2.593±.020
[65.86±0.51]
.915
[23.24]
.365
[9.27]
2 Plc.
.120
[3.05] Dia.
4 Plc.
2.282
[57.96]
.016
[0.41] R
Typ.
.130
[3.30] Dia.
or
.218
[5.54] Dia.†
.218
[5.54] Dia.
4 Plc.
.120
[3.05] Dia.
2 Plc.
Mixed 42 Position
Material and Finish
Housing - Phenolic, black or
diallyl phthalate, blue, 94V-O
rated
Contacts must be ordered
separately.
Special Application Connectors
75
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors (Continued)
High Voltage 20
Position UL Voltage
Rating: 1800 V
Material and Finish
Housing - Diallyl phthalate,
94V-O rated, blue
Contacts must be ordered
separately.
.782
[19.86]
.157
[3.99]
.234
[5.94]
.078
[1.98] R Typ.
.468
[11.89]
1.686
[42.82]
Recommended Panel Cutout Plug Housing Receptacle Housing
.750
[19.05]
2.000
[50.80]
.375
[9.53]
Typ.
1.411
[35.84]
.090
[2.29] R
4 Plc.
.093
[2.36] R
Typ.
.155
[3.94] Dia.
4 Holes
Plug Housing
Wiring Side
Receptacle Housing
Wiring Side
Diallyl Phthalate
Housing Part No. Contacts Accepted
Plug Receptacle Quantity Contact Type Page Ref.
Type II 30
Type III+ 31-35
203908-2 203909-2 20* Subminiature
COAXICON 40, 41
*Quantity may be all of the same type, or a combination of those types listed.
Note: 20 Position connector uses Standard 34 Position Hardware. Refer to appropriate column of
Application Charts for Hardware Selection pages 10 through 25.
.119
[3.02]
1.448
[36.78]
.960
[24.38]
Special Application Connectors
AMP M Series
Pin and Socket Connectors
76
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors (Continued)
High Voltage 28
Position UL Voltage
Rating: 1800 V
Material and Finish
Housing - Phenolic, 94V-O
rated, black
Contacts must be ordered
separately.
.500
[12.70]
.140
[3.56]
.327
[8.31]
.156
[3.96] Dia.
4 Holes
.128
[3.25]
2.025
[51.44]
Recommended Panel Cutout
Plug Housing
Receptacle Housing
2.595±.020
[65.91±0.51]
1.305
[33.15]
.015
[0.38] R
Typ.
.766
[19.46]
2.281
[47.94]
.120
[3.05] Dia.
4 Plc.
1.155
[29.34]
.195
[4.95]
.365
[9.27]
1.983±.010
[50.37±0.25]
1.110±.010
[28.19±0.25]
2.595±.020
[65.91±0.51]
.915
[23.24]
.120
[3.05] Dia.
4 Plc.
.365
[9.27]
1.983±.010
[50.37±0.25]
1.110±.010
[28.19±0.25]
.766
[19.46]
.156
[3.96] Dia.
4 Plc.
.156
[3.96] Dia.
4 Holes
Phenolic
Housing Part No. Contacts Accepted
Plug Receptacle Quantity Contact Type Page Ref.
Type II 30
Type III+ 31-35
205689-2 205690-2 28* Subminiature
COAXICON 40, 41
*Quantity may be all of the same type, or a combination of those types listed.
Note: 28 Position connector uses Standard 75 Position Hardware. Refer to appropriate column of
Application Charts for Hardware Selection Pages 10 through 25.
Special Application Connectors
77
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Special Application Connectors (Continued)
Grounding Blocks
Material and Finish
Plate - Brass, tin plated
Clinch Nuts - Stainless steel
Pin Contacts - Phosphor
bronze, gold over nickel
plated
Jackscrews
Material and Finish
Jackscrew Body - Die cast
zinc, (clear chromate) con-
version coating
Jackscrew Tip, Roll Pin -
Stainless steel
14-Position, Part No. 203540-1*
34-Position, Part No. 204814-1*
Grounding blocks mate with standard 14 and 34 position receptacle housings.
Note: Use referenced turnable jackscrews on mating housings when mating to grounding blocks.
*CSA Certification pending.
Short Turnable
Jackscrew, Male
Part No. 203618-1
(2 Req’d.)
Short-Short Turnable
Jackscrew, Male
Part No. 203535-2
(2 Req’d.)
1.098
[27.89]
.562
[14.27]
1.250±.020
[31.75±0.51]
.059
[1.50] R.060
[1.53]
Typ.
.620
[15.75]
.062
[1.57] Dia.
Typ.
.937
[23.80]
.492
[12.50]
2.000±.020
[50.80±0.51]
.059
[1.50] R
.060
[1.53]
Typ.
.930
[23.62]
.062
[1.57] Dia.
1.686
[42.82]
.492
[12.50]
Fastening Hardware - For
use in connector housings to
mate with grounding blocks
Special Application Connectors
AMP M Series
Pin and Socket Connectors
78
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Fastening Hardware
Male Female Male Female
Long-Long Long
Male Female Male Female
Short Short-Short
Roll
Pin
3.285
[83.44]
(Assembled)
3.305
[83.95]
(Assembled)
2.285
[58.04]
(Assembled)
2.305
[58.55]
(Assembled)
1.180
[29.97]
(Assembled*)
1.200
[30.48]
(Assembled*)
AMP Assembly Tool
Part No. 91016-2
(for Roll Pins)
Nut Driver
Part No. 811262-1 (4-40)
Turnable Jackscrews
* Assembled dimension includes metal thickness of Pin Hood or Strain Relief Clamp. Remove washer when
both Pin Hood and Strain Relief Clamp are used.
Roll
Pin
Roll
Pin
Roll
Pin
Roll
Pin
Roll
Pin Roll
Pin
Roll
Pin
Flat
Washer
Flat
Washer
1.670
[42.42]
(Assembled)
1.648
[41.84]
(Assembled)
Turnable Jackscrews
Jackscrew Part No. Connectors Used on (No. of Positions)
6-32 [M3.5 x 0.6] 6-32 [M3.5 x 0.6] Special Application
Style Double Lead Single Lead Standard Posted High High
Thread Thread
Current Mixed Voltage
Long-Long
Male1 201911-1 207234-1 50 (90°
Long-Long shield only), — 12 42 28
Female1 201910-1 207235-1 75 and 104
Long
Male 1-200871-0 201413-4 20, 26, 34, 41, 20, 26, 34, 41, 15, 16 20
Long and 50 and 50 12 and 42 and 28
Female 1-200867-1 201414-4
Short
Male 200868-1 201087-1 6, 14, 20, 26, 6, 14, 20, 26, 34, 15, 16 20
Short 34, 41, 50, 34, 41, 50, 12 and 42 and 28
Female 200870-1 201088-1 75 and 104 75 and 104
Short-Short
Male 201388-1 201827-1 6, 14, 20, 26, 6, 14, 20, 26, 34, 15, 16 20
Short-Short 34, 41, 50, 34, 41, 50, 12 and 42 and 28
Female 201389-1 201828-1 75 and 104 75 and 104
1Long-Long Turnable Jackscrews are used only with Two-Piece Shields on the connector sizes listed.
Notes: 1. Turnable Jackscrews mate with any Fixed Jackscrew listed below having the same thread size.
2. Special Turnable Jackscrews for use in connector housings to mate with Grounding Blocks are
presented on page 77.
3. Single-lead versions are designed to mate with competitive Jackscrews.
Roll pins for turnable jackscrews, Long-Long, Long, Short Part No. 201501-1, Short-Short Part No. 201501-2.
Jackscrews
Material and Finish
Turnable Jackscrew Body -
Die cast zinc, chromate
conversion coating
Turnable Jackscrew Tip -
Stainless steel
Roll Pin - Stainless steel
For Fixed Jackscrews
Lockwasher - Steel
Hex Nut - Steel, zinc plated
Jackscrews are used as an
aid in mating and unmating
connectors and for holding
mated connectors together,
mostly larger sizes (34-posi-
tion and up). They can also
be used for polarization.
Turnable jackscrews are free
to rotate in a connector hous-
ing and are always used
opposite mating fixed jack-
screws. Where provided, roll
pins are used to hold a male
or female tip onto the turn-
able jackscrew body.
AMP Assembly Tool No.
91016-2 (shown below) is
available for properly assem-
bling the turnable jackscrews
on a connector housing.
Fixed jackscrews can be
readily assembled to a
connector housing with the
Nut Driver Tool (also shown
below).
Hardware
79
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Fastening Hardware (Continued)
Fixed Jackscrews
Jackscrew Part No.
6-32 [M3.5 x 0.6] 6-32 [M3.5 x 0.6]
Type Double Lead Single Lead
Thread Thread
Male 1-200874-2 201092-4
Female 200875-7 201089-4
Notes: 1. Fixed Jackscrews mate with any Turnable Jackscrew listed
above having the same thread size.
Notes: 2. Single-lead versions are designed to mate with competi-
tive Jackscrews.
Notes: 3. Double-Lead Thread and Single-Lead Thread Jackscrews
can NOT be mixed; i.e., Double-Lead must mate with
Double, Single-Lead with Single.
Notes: 4. Double-Lead Thread has two leads in the same revolution
versus one lead for Single-Lead Thread. Therefore,
Double-Lead Thread will pick up twice as fast.
Male Female
4-40
Hex Nut
Lock
Washer
.815
[20.7]
4-40
Hex Nut
Lock
Washer
.840
[21.34]
Fixed Jackscrews
Hardware
AMP M Series
Pin and Socket Connectors
80
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Fastening Hardware (Continued)
Standard
Connector A
Size* Max.
1.413
6 35.89
1.662
14 42.21
1.975
20 50.17
2.037
26 51.74
2.412
34 61.26
3.047
41 77.39
3.006
50 76.35
* A dimension also applies to
other comparably sized con-
nector types listed in the chart
at the right.
.375
[9.53]
.375
[9.53]
A Max.
(Assembled)
A Max.
(Assembled)
Female
Male
.320
[8.13]
.620
[15.75]
.375
[9.53]
.375
[9.53]
A Max.
(Assembled)
A Max.
(Assembled)
Female
Male
.320
[8.13]
.620
[15.75]
Locking Spring Part No. Connectors Used On (No. of Positions)
Male Female Special Application
(Spring (Latching Standard Posted High High
Member) Member)
Current Mixed Voltage
6, 14, 20 6, 14, 20
201921-1 201922-1 and 41 and 41 — — —
201923-1 201918-1* 26 26 — 15 —
201925-1 201926-1 34 and 50 34 and 50 — 16 and 42 20
*Single female latch, two must be ordered per assembly.
For Housings with
Three Mounting Holes
For Housings with
Single Mounting Hole
Locking Springs
Material and Finish
Male (Spring Member) -
Spring steel, nickel plated
Female (Latching Member) -
Stainless steel
Locking Springs are used
to hold mated connectors
together. Although Locking
Springs can be used on con-
nectors up to 50 positions,
they are primarily used on
smaller size connectors (less
than 34 positions).
In all applications, a Male
(Spring Member) is used
opposite a Female (Latching
Member). They can be secured
to a connector housing using
Guide Pins and Sockets or
4-40 x .250 [6.35] fillister
head screws and nuts. Locking
Springs can be used with all
hardware, except Closed-End
Pin Hoods.
Hardware
81
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Guiding Hardware
Guide Pins and
Sockets
Material and Finish
Guide Pins and Sockets—
Stainless steel
Lockwashers—Stainless steel
Hex Nuts—Steel, zinc plated
Guiding hardware is used to
align connector halves during
mating. This hardware can
also be used for keying con-
nectors to provide for proper
mating. Guiding hardware can
be readily secured to connec-
tor housings using the Nut
Driver Tool shown below.
Center Guide Pins and Sockets
are used primarily in housings
having a single mounting hole,
but can also be used in the
centermost hole of housings
having 3 or 4 mounting holes.
Corner Guide Pins and Sockets
are used in the corner holes of
housings having 2, 3 or 4
mounting holes. They cannot
be used in center mounting
holes which are slightly
deeper than corner mounting
holes to accept Jackscrews.
6-32
Hex Nut
(75, 104, 160CF Pos.)
6-32
Hex Nut
(75, 104, 160CF Pos.)
4-40
Hex Nut 4-40
Hex Nut
6-32
Hex Nut
6-32
Hex Nut
6-32
Hex Nut
4-40
Hex Nut
(34 & 50 Pos.)
4-40
Hex Nut
(34 & 50 Pos.)
Lock
Washer
Lock
Washer
Lock
Washer Lock
Washer
Spacer
Spacer
1.097
[27.86] .625**
[15.88]
1.156
[29.36]
.840
[21.34] .780
[19.81]
.830
[21.08]
.795*
[20.19]
Pin Socket Pin
Pin
Socket
Socket Long Pin
Corner Guide
Corner Guide (104 CF)
Center Guide
Lock
Washer
Lock
Washer
Lock
Washer
Nut Driver
Part No. 811262-1 (4-40)
Part No. 811262-2 (6-32)
Connectors Used On (No. of Positions)
Guide Pins and Sockets Special Application
Type Part No. Standard Posted High High
Current Mixed Voltage
Center Pin 200389-2 6, 14, 20, 26, 34, 6, 14, 20, 26, 34,
200390-9 41, 50, 75 and 104 41, 50, 75 and 104 12 15, 16 and 42 20 and 28
Center Socket 207619-1*2
Corner Pin 1-200833-1
1-200835-1 34 and 50 34 and 50 — 16 and 42 20
Corner Socket 203964-1*
Corner Pin 1-201046-2
201047-2 75, 104 and 160 CF 75, 104 and 160 CF 12 29 28
Corner Socket 203966-1*
Corner Pin 202173-8
202173-73
202174-5
Corner Socket 202174-43 104 CF 104 CF — — —
204099-2**
Long Pin1 201540-1
1Two Long Pins are to be installed in diagonal corners. Use without Guide Sockets.
2Hex Nut Stainless Steel.
3Without Spacer.
** These Corner or Center Guide Sockets (.880 [22.35] long) are to be used when housings are loaded with
Subminiature COAXICON contacts.
** Corner Socket, Part No. 204099-2 (.838 [21.29] long), is to be used when housings are loaded with
Subminiature COAXICON contacts.
Hardware
AMP M Series
Pin and Socket Connectors
82
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Protective Hardware
A
B
C
A
B
C
Internal Open-End Internal Closed-End
Pin Hoods, Internal Open-End
Connectors Used On (No. of Positions)
Dimensions Pin Hood Special Application
A B C Material Part No. Standard Posted High High
Current Mixed Voltage
1.000 .500 .718 Nickel Plated
25.4 12.7 18.24 Steel 204258-6 6 6 — — —
1.250 .550 .718 Nickel Plated
31.75 13.97 18.24 Steel 201363-4 14 14 — — —
1.632 .725 .718 Nickel Plated
41.45 18.42 18.24 Steel 201785-4 26 26 — 15 —
2.000 .880 .718 Nickel Plated
50.8 22.35 18.24 Steel 201786-4 34 34 — 16 20
Note: Typical Internal Open-End and Closed-End Pin Hoods are illustrated. Slight differences in configu-
ration exist for various sizes. The mounting holes and/or slots in each Pin Hood match the
mounting hole pattern of the connector housing on which the Pin Hood is used.
Pin Hoods, Internal Closed-End
Connectors Used On (No. of Positions)
Dimensions Pin Hood Special Application
A B C Material Part No. Standard Posted High High
Current Mixed Voltage
2.130 .880 .687 Nickel Plated
54.1 22.35 17.45 Steel 202434-4 34 34 — 16 20
2.875 .952 .687 Nickel Plated
73.02 24.18 17.45 Steel 202394-2 50 50 — 42 —
2.765 1.310 .687 Nickel Plated
70.23 33.27 17.45 Steel 201369-4 75 75 12 — 28
2.975 1.740 .687 Nickel Plated
75.57 44.2 17.45 Steel 201364-4 104 104 — — —
2.975 2.040 .687 Nickel Plated
75.57 51.82 17.45 Steel 203743-4 CF160 CF CF160 CF — — —
Pin Hoods, Internal
Open-End and Closed-
End
Material and Finish
See charts
Pin Hoods are used to
protect pin contacts that
protrude from a connector
housing.
When contacts are mixed
(pins and sockets in both
housings), an Internal Pin
Hood is used on one housing
and an External Pin Hood
(page 83) is used on the
other housing. Or a Long
Shield is used on one housing
and an External Pin Hood
must be used on the other
housing. When a housing is
loaded with all pin contacts,
an Internal or External Pin
Hood may be used—no Pin
Hood is required on the mat-
ing half.
External Open-End Pin
Hoods with flanges (page 83)
are used primarily for mount-
ing a connector with pin
contacts to a panel.
All Pin Hoods may be
secured to connector hous-
ings using other appropriate
hardware, such as Jackscrews
and Guide Pins and Sockets.
Hardware
83
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Protective Hardware (Continued)
Pin Hoods, External Open-End with Flanges
Connectors Used On (No. of Positions)
Dimensions Pin Hood Special Application
A B C Material Part No. Standard Posted High High
Current Mixed Voltage
2.875 .891 .687 Nickel Plated
73.02 22.63 17.45 Steel 202095-5 34 34 — 16 20
3.375 .565 .687 Nickel Plated
85.73 14.35 17.45 Steel 202165-5 41 41 — — —
3.468 .891 .687 Nickel Plated
88.09 22.63 17.45 Steel 202096-5 50 50 — 42 —
Pin Hoods, External Closed-End
Connectors Used On (No. of Positions)
Dimensions Pin Hood Special Application
A B C Material Part No. Standard Posted High High
Current Mixed Voltage
1.880 .812 .687 Aluminum
47.75 20.62 17.45 Iridite 201349-2 26 26 — 15 —
2.250 1.000 .687 Aluminum
57.15 25.4 17.45 Iridite 201350-2 34 34 — 16 20
2.845 1.000 .687 Nickel Plated
72.26 25.4 17.45 Steel 201390-5 50 50 — 42 —
2.845 1.360 .687 Nickel Plated
72.26 34.54 17.45 Steel 201368-4 75 75 12 29 28
3.025 1.800 .687 Nickel Plated
76.84 45.72 17.45 Steel 201346-4 104 104 — — —
3.040 1.340 .718 Nickel Plated
77.22 34.04 18.24 Steel 202119-2 CF104 CF CF104 CF — — —
3.025 2.100 .687 Nickel Plated
76.84 53.34 17.45 Steel 203744-4 CF160 CF CF160 CF — — —
External Closed-End External Open-End with Flanges
Note: Typical External Closed-End and Open-End (with Flanges) Pin Hoods are illustrated. Slight differ-
ences in configuration exist for various sizes. The mounting holes and/or slots in each Pin Hood
match the mounting hole pattern of the connector housing on which the Pin Hood is used.
A
B
A
B
C
Pin Hoods, External
Closed-End and
Open-End (with
Flanges)
Material and Finish
See charts
C
Hardware
AMP M Series
Pin and Socket Connectors
84
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Shields, Two-Piece,
180° and 90° Cable
Exit
Material and Finish
Shields - See charts
Cable Clamp - Steel, nickel
plated
Screws - Steel, zinc plated
These Two-Piece Shields are
used to protect connectors
from dust, dirt and physical
damage and to provide strain
relief for the contacts. They
feature integral cable clamps
formed at 180° and 90° and
are available in long and short
versions. Long versions offer
pin protection as well as con-
nector protection and strain
relief. Short versions may be
used in combination with Pin
Hoods to provide pin protec-
tion.
For shielding and fastening
applications, Two-Piece Shields
are used with Jackscrews.
They may be secured to a
connector housing using other
appropriate hardware such as
Guide Pins and Sockets.
Two-Piece Shields with cable
clamps formed at 45° are
available, see page 87.
Tyco Electronics does NOT
recommend the use of shields
with posted connectors
because of the potential of
shorting.
180° Cable Exit
90° Cable Exit
A
(Assembled)
C
(Long,
Assembled)
D
(Short)
D
(Long)
B
C
(Assembled)
A
(Assembled)
D
(Short)
D
(Long)
B
C
(Short,
Assembled)
Protective Hardware (Continued)
Hardware
85
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Two-Piece Shields, 180° Cable Exit (Long and Short)
Connectors Used On (No. of Positions)
Dimensions Shield Part No. Max. Special Application
A B C D Material Long Short Cable Standard High High
Dia.
Current Mixed Voltage
.520 1.562 1.815 1.300 Nickel Plated .375
13.21 39.67 46.10 33.02 Steel — 204087-1 9.53 20 — — —
Anodized
2.453 1.970 Aluminum 201576-1 —
.640 1.625 62.31 50.04 Nickel Plated .415
16.26 41.28 Steel 201576-2 — 10.54 26 — 15 —
1.781 1.300 Nickel Plated
45.24 33.02 Steel — 200514-2
Anodized
2.453 1.937 Aluminum 201571-1 —
62.31 49.2 Nickel Plated
.828 2.000 Steel 201571-2 — .500
21.03 50.8 Anodized 12.7 34 — 16 20
1.765 1.250 Aluminum — 200517-1
44.83 31.75 Nickel Plated
Steel — 200517-9
.515 2.687 2.453 1.968 202383-2 —
13.08 68.25 62.31 49.99 Nickel Plated .435
.515 2.687 1.781 1.290 Steel
11.05 41 — — —
13.08 68.25 45.24 32.77 — 202383-1
Anodized
2.468 1.970 Aluminum 201443-1 —
62.69 50.04 Nickel Plated
.828 2.593 Steel 201443-2 — .550
21.03 65.86 Anodized 13.97 50 — 42 —
1.796 1.290 Aluminum — 200532-1
45.62 32.77 Nickel Plated
Steel — 200532-2
3.327 2.797
1.195 2.727 84.51 71.04 Nickel Plated 202713-2 — 1.000
30.35 69.27 2.655 2.125 Steel
25.4 75 12 — 28
67.44 53.98 — 202713-1
1.703 2.765 1.843 1.290 Nickel Plated .800
43.26 70.23 46.81 32.77 Cast Aluminum — 201131-1 20.32 104 — — —
Two-Piece Shields, 90° Cable Exit (Long and Short)
Connectors Used On (No. of Positions)
Dimensions Shield Part No. Max. Special Application
A B C D Long Short Cable Standard High High
Dia.
Current Mixed Voltage
2.797
.900 2.592 3.098 71.04 203975-2 — .550
22.86 65.84 78.69 2.125
13.97 50 — 42 —
53.98 — 203975-1
2.797
1.195 2.730 3.260 71.04 202711-3 — 1.000
30.35 69.34 82.80 2.125 25.4 75 12 — 28
53.98 — 202711-1
1.145 2.845 3.375 2.375 1.000
29.08 72.26 85.73 60.33 — 202395-1 25.4 CF104 CF — — —
Notes: 1. All parts are packaged unassembled.
2. Material: nickel plated steel.
Protective Hardware (Continued)
Hardware
AMP M Series
Pin and Socket Connectors
86
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Protective Hardware (Continued)
A
180° Cable Exit 90° Cable Exit
Note: Typical 180° and 90° Cable Exit Shields are illustrated. Slight differences in configuration exist for
various sizes.
A
B
B
C
(Short,
Assembled) D
(Short) D
(Short)
D
(Long)
C
(Long,
Assembled)
One-Piece Shields, 180° Cable Exit (Long and Short)
Connectors Used On (No. of Positions)
Dimensions Shield Part No. Max. Special Application
A B C D Long Short Cable Standard High
Dia. Mixed Voltage
2.468 1.969
.531 1.312 62.69 50.01 201378-2 — .375
13.49 33.32 1.796 1.300 9.53 14 — —
45.62 33.02 — 201360-2
.515 1.640 1.796 1.300 — 201227-2 .350 20 — —
13.08 41.66 45.62 33.02 8.89
.640 1.687 1.796 1.296 — 201169-2 .400
16.26 42.85 45.62 32.92
10.16 26 15 —
2.468 1.969
.828 2.062 62.69 50.01 201384-2 — .500
21.03 52.37 1.781 1.281 12.7 34 16 20
45.24 32.54 — 201165-2
One-Piece Shields, 90° Cable Exit (Short)
Connectors Used On (No. of Positions)
Dimensions Shield Part No. Max. Special Application
A B C D Short Cable Standard High
Dia.
Mixed Voltage
.828 2.062 2.562 1.812 .500
21.03 52.37 65.07 46.02 201469-2 12.7 34 16 20
Note: All parts are packaged unassembled.
C
(Assembled)
Shields, One-Piece,
180° and 90° Cable
Exit
Material and Finish
Shields and Cable Clamps -
Steel, nickel plated
Screws - Steel, zinc plated
One-Piece Shields are used to
protect connectors from dust,
dirt and physical damage and
to provide strain relief for the
contacts. They feature integral
cable clamps formed at 180°
and 90° and are available in
long and short versions. Long
versions offer pin protection
as well as connector protec-
tion and strain relief. Short
versions may be used in com-
bination with Pin Hoods to
provide pin protection.
For shielding and fastening
applications, One-Piece
Shields are used with Locking
Springs. They cannot be used
with Jackscrews.
One-Piece Shields may be
secured to a connector hous-
ing using other appropriate
hardware such
as Guide Pins and Sockets.
Tyco Electronics does NOT
recommend the use of shields
with posted connectors
because of the potential of
shorting.
Hardware
87
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Protective Hardware (Continued)
Shields,Two-Piece,
45° and 30° Cable Exit
Material and Finish
Shields and Cable Clamps -
Steel, nickel plated
Screws - Steel, zinc plated
These Two-Piece Shields are
used to protect connectors
from dust, dirt and physical
damage and to provide strain
relief for the contacts. They
feature integral cable clamps
formed at 45° and are specif-
ically designed for use with
104 CF and 160 CF position
standard connectors; 30° exit
shield is available for 29 CF
position connectors.
These Shields may be used
with Pin Hoods to provide
pin protection.
These Two-Piece Shields may
be secured to a connector
housing using other appropri-
ate hardware such as Guide
Pins and Sockets.
Tyco Electronics does NOT
recommend the use of
shields with posted connec-
tors because of the potential
of shorting.
B
C
A
Assembled
45° Cable Exit
Note: A typical 45° Cable Exit Shield is illustrated. Slight differences in configuration exist between sizes.
Two-Piece Shields, 45° Cable Exit
Max. Connectors Used On
Dimensions Shield Part No. Cable (No. of Positions)
A B C Dia. Standard
2.375 1.000
1.145 2.845 60.33 202169-4 25.4
29.08 72.26 1.875 .650 104 CF
47.63 202110-1 16.51
1.845 2.770 2.750 1.200
46.86 70.36 69.85 202798-1 30.48 160 CF
Note: All parts are packaged unassembled.
Two-Piece Shield, 30° Cable Exit
Max. Connectors Used On
Dimensions Shield Part No. Cable (No. of Positions)
A B C Dia. Standard
1.375 2.685 3.440 1.250
34.93 68.19 87.38 202483-3 31.75 29 CF
Hardware
AMP M Series
Pin and Socket Connectors
88
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Strain Relief Hardware
Strain Relief Clamps
Material and Finish
Clamp—Steel, nickel plated
Hex Nuts—Steel, zinc plated
“U” Bolt—Stainless steel
Sleeves—Black plastic
Bracket—See chart
Strain Relief Clamps are used
to relieve the stress of the
wires on the contacts and to
group the wires where they
enter a connector. Both long
and short versions are avail-
able. The long versions are
normally used for all applica-
tions and provide a greater
distance between the wire
bundle and the connector for
operating Jackscrews with-
out interference. The short
versions are ideally suited for
applications where space is
limited.
Tyco Electronics does NOT
recommend the use of Strain
Relief Clamps with posted
connectors because of the
potential of shorting.
L
B
A
C
(Assembled)
W
Cable Opening
Shown for
180° Cable Exit
Shown for
90° Cable Exit
Note: A typical Strain Relief Clamp is illustrated. Slight differences in configuration exist for various sizes.
Cable Clamps (Long and Short)
Cable Strain Relief Connectors Used On (No. of Positions)
Bracket Dimensions Opening Clamp Part No. Special Application
Material A B C L x W Long Short Standard High Mixed High
Current Voltage
1.000 1.125 .305 x .155
25.4 25.58 — 7.75 x 3.94 — 203432-1 6 — — —
Steel, 2.125 2.687
Nickel 1.250 53.98 68.25 .530 x .335 201843-3 —
Plated 31.75 1.125 1.687 13.46 x 8.51 14 — — —
28.58 42.85 — 200686-4
Stainless 1.562 1.187 2.000 .780 x .335
Steel 39.67 30.15 50.8 19.81 x 8.51 — 201237-2 20 — — —
2.125 2.937 .780 x .505
Steel, 1.625 53.98 74.6 19.81 x 12.83 201845-2 —
Nickel 41.28 1.250 2.062 .780 x .430 26 — 15 —
Plated 31.75 52.37 19.81 x 10.92 — 201229-5
2.281 2.851 .780 x .500
2.000 57.94 72.42 19.81 x 12.7 201846-5 —
50.8 1.500 2.265 .780 x .425 34 — 16 20
38.1 57.33 19.81 x 10.8 — 201224-7
Stainless 2.625 2.000 3.343 1.500 x .360
Steel 66.68 50.8 84.91 38.1 x 9.14 201766-1 — 41 — — —
2.593 2.406 3.296 1.125 x .675
65.86 61.11 83.72 28.58 x 17.15 201847-1 —
Steel, 2.562 1.703 2.780 1.125 x .550 50 — 42 —
Nickel Plated 65.07 43.26 70.61 28.58 x 13.97 — 201182-4
Stainless 2.594 2.531 3.717 1.125 x .925
Steel 65.89 64.29 94.41 28.58 x 23.5 201848-5 —
2.625 1.734 2.874 1.125 x .800 75 12 — 28
Steel, 66.68 44.04 73.0 28.58 x 20.32 — 200730-4
Nickel 2.750 2.531 3.389 1.125 x 1.235
Plated 69.85 64.29 86.08 28.58 x 31.37 201849-3 — 104 — — —
Notes: All parts are packaged unassembled.
Hardware
89
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Keying Hardware
Keying Plug (for
Multimate Contact
Cavities)
Material
Natural color nylon
This cylindrical keying plug is
used in Multimate contact
cavities that accept Type II,
Type III+ and Subminiature
COAXICON socket contacts.
The plug protrudes from the
mating face of a connector
and will prevent connector
halves from being mated by
butting against the pin con-
tact. The mating pin contact
must be removed to provide
for proper mating.
Keying Plugs (for Type
XII Contact Cavities)
Material
For 207597-1—Gray nylon
For 206508-1—Natural color
nylon
Two versions of rectangular
keying plugs are available for
Type XII contact cavities. A
pin style is used in cavities
that accept Type XII male
contacts, and a plug style is
used in cavities that accept
Type XII female contacts.
These keying plugs perform
the same as the cylindrical
keying plug described above.
The mating contact must also
be removed to provide for
proper connector mating.
Male
Contact
Cavities
Pin Style
Plug Style
Female
Contact
Cavities
1.000
[25.4]
Part No. 200821-1
1.730
[43.94]
Part No. 207597-1
1.750
[44.45]
Part No. 206508-1
Hardware
AMP M Series
Pin and Socket Connectors
90
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Mechanical Hand Tools
for Interchangeable Die
Sets
These tools are ideal for small pro-
duction, prototype and
experimental applications. They
are used for terminating pin and
socket contacts to wire and fea-
ture a ratchet device to provide
consistently formed crimps.
PRO-CRIMPER III Hand
Tool, Part No. 58495-1
Commercial grade hand
tool for crimping various
products. Features ratchet
control to provide complete
crimp cycle. Accepts both
pinned- and shouldered-
style die sets. Locators are
provided with pinned-style
die sets for proper contact
and wire positioning, and
to help minimize contact
rotation and bending during
crimping. Approximate
weight 1.3 lb [0.60 kg].
For use with Type III+ contacts,
see pages 17-19.
For more information, request
Catalog 1773379-1, Instruction
Sheet 408-9930.
Application Tooling
CERTI-CRIMP Straight
Action Hand Tools (SAHT)
Premium grade hand tools.
Feature ratchet control to
provide complete crimp
cycle. Die sets close in
a straight line. Include a
contact locator and wire
stop, plus an insulation crimp
adjustment lever, when
applicable. Approximate
weight 1.3 lb [0.59 kg].
For Type III+ contacts, see pages
17-19.
For more information, request
Catalog 65780.
112076
CERTI-CRIMP “C” Head
Straight Action Hand Tool
(SAHT), Part No. 69710-1
Premium grade hand tool.
Features ratchet control
to provide complete crimp
cycle. The interchangeable
die sets close in a straight
line to minimize contact
or terminal rotation during
crimping. When applicable,
user-assist features such as
a contact or terminal locator
and a wire stop, are built into
the die set. Approximate
weight 1.9 lb [0.86 kg].
For subminiature coaxial
contacts, see pages 22-23.
For more information, request
Catalog 65780, Instruction Sheet
408-2095.
92936-8
Electric Machine for
Interchangeable Die Sets
SDE Terminator,
Part No. 1490076-2
An electric crimp terminator
with compact design features
a die set holder that is
compatible with all AMP SDE
(PRO-CRIMPER III Tool) die
sets. Hand- or foot-actuated
options are available. CE
Approved.
For more information, request
Catalog 1654714.
112383
SDE (Standard Die
Envelope) Die Sets
SDE die sets provide cost-
effective flexibility, through
many options for a common
die-set outline. The SDE die
sets can be adapted for use
with CERTI-CRIMP hand
tools, PRO-CRIMPER III hand
tools, the SDE Terminator
and the 626 Pneumatic Tool
System.
For more information, request
Catalog 1654003.
Application Tooling
91
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Pneumatic Hand Tool for
Interchangeable Die Sets
6-26 Pneumatic Tool
System
Effortless crimping for a
broad range of terminals,
either bench-mounted or
hand-held for working in
cramped quarters.
• Lightweighttooleliminates
physical force required by
hand tools
• Hand-orfoot-switch
operation
• Terminationwire
range from 26-6 AWG
[0.12-13.0mm2], plus coaxial
and fiber optic cable
• WorkswithexistingAMP-
compatible crimp heads
and die sets
• Ratchetcontroloptionpro-
vides complete crimp cycle,
eliminating partial crimps
• Userotatinghead
assembly to reach difficult
termination locations
For more information, request
Catalog 124208.
Battery-Powered Crimp
Tool Kits
The Battery-Powered
Crimp Tool Kit is a fast,
ergonomically-designed
tool is ideal for use at the
bench, on the line, or in
the field. It’s completely
portable, lightweight (3.48
lbs including battery) and
compact. The charge delivers
over 100 crimps - charge time
is 40 mins. The kit includes
the tool, 2 batteries and the
charger.
P/N 1213890-1 — SDE Battery
Powered Crimp Tool Kit
(dies not included)
P/N 1213805-1 — CERTI-
CRIMP II, SA Battery
Powered Crimp Tool Kit
(heads not included)
P/N 1213840-1 — CERTI-
CRIMP, Large Die, C-Head
Adapter Battery Powered
Crimp Tool Kit (dies not
included)
P/N 1213819-1 — CERTI-CRIMP,
Large Die, Straight-Action
Adapter Battery Powered
Crimp Tool Kit (dies not
included)
For more information, request
Catalog 1773381.
Application Tooling (Continued)
CRIMP MACHINES
Semiautomatic bench
machines for crimping
reeled terminals and con-
tacts, featuring a quiet and
reliable direct motor drive,
microprocessor controls for
ease of setup and operation,
and guarding and light-
ing designed for operator
convenience and safety. All
models are equipped with
either manual or automatic
precision adjustment of crimp
height. Machine-mounted
sensors are available for
crimp quality monitoring
using conventional miniature-
style applicators.
For more information, request
Catalog 1654956-2, Video 198116,
Catalog 82275 [Crimp Quality
Monitor (CQM)], Video 198094.
Note: New Stripping Module
available, see page 79.
AMP-O-LECTRIC Model
“G” Terminating
Machines, Part Nos.
354500-1, -9, -11
AMP-O-LECTRIC Model “K”
Terminating Machine with a
permanently-mounted ap-
plicator that accepts inter-
changeable die sets to apply
a variety of tape-mounted
terminals and splices. Many of
the die sets can also be used
in AMP-O-LECTRIC Termi-
nating Machines with a tape
applicator.
For more information, contact
Tyco Electronics.
AMP-TAPETRONIC
Machine, Part No. 69875
103330
Application Tooling
AMP M Series
Pin and Socket Connectors
92
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Application Tooling (Continued)
The unique system pro-
vides 100% on-the-fly crimp
inspection. It measures the
crimp height of each termina-
tion, and evaluates the quality
of each crimp. If a crimp is
questionable, the monitor
alerts the operator with both
visual and audible alarms. It
also provides ports for print-
ing and networking. When
used with AMP-O-LECTRIC
Model “G” Termination Ma-
chines, the monitor is mount-
ed to the machine. When
used with AMPOMATOR CLS
IV Lead Making Machines, it is
integrated into the machine’s
operating system.
For more information, request
Catalog 82275.
Crimp Quality Monitor
(CQM)
Part No. 1320420-2
The System III Applicator
introduces several new tech-
nologies into the applicator
including a precision servo-
electric motorized feed-
ing system, a built-in data
module for storing terminal
crimp and set-up information,
a precision fit round ram, and
a newly designed terminal
depressor. It still utilizes the
proven quality of the HD-M
crimper and anvil tooling.
For more information, request
Catalog 1654956-8
System III Applicator
The AMP 3K/40 and AMP
5K/40 Terminators are
designed for customers
that require the increased
output and quality of a
semiautomatic machine
at a competitive price. By
incorporating the most
commonly requested
features as standard and
offering a long list of optional
equipment, these terminators
offer flexibility to meet the
specific needs of various
applications at the lowest
possible cost.
Features
3,000 lb [1361 kg] max. •
crimp force (AMP 3K/40);
5,000 lb [2268 kg] max. •
crimp force (AMP 5K/40)
Toolless removal of •
applicators and guards
Jog capability•
Quiet, fast operation - •
80/76 dBA and cycle time
less than 0.400 seconds
Accepts Heavy Duty Mini •
stye applicators
Wide range of optional •
equipment such as toolless
precision crimp height
adjust, batch counter, CQM
capability and work light
For more information, request
Catalog 1654956-2.
Note: New Stripping Module
available, see page 79.
AMP 3K/40 and AMP
5K/40 Terminating
Machines
Your Quality Program
calls for more than a
Good Crimping System. It
demands proof — the proof
you get with the SLE crimp
force monitor. It has high-
resolution piezo-quartz
sensor technology for a
more precise identification of
typical crimping faults.
Sure, you can sample and
test crimp height with a
micrometer. In fact, that’s
how you standardize your
process. But for ongoing
quality control, testing every
crimp, SLE is the choice.
It’s known worldwide, and
meets our standards or a
high performance terminating
system. That’s how you can
be sure.
High quality crimping — with
verification — means higher
production and productivity.
Crimp Force Monitor
(CFM)
Features
• 1or2Channels
• 128x128DotMatrix
• Zone&PeakForce
Analysis
• ForceTrigger
• EncoderProximityTrigger
• AbsoluteForce
Measurement
• Monitorsthewirebarrel
crimp of open-barrel,
uninsulated contacts and
terminals
• Real-timemonitoringof
every crimp
• Specialapplicatorsarenot
required
• UsewiththeAMP-3K/40
and AMP-5K/40 presses
from Tyco Electronics
• Frame-mountedforce
sensor
• Forbenchorfully-
automatic machines
• Pleasecontactusforany
other type of press you
would like to use with the
CFM
Crimp Force Monitor
Specifications
• Electrical:110-230VAC
Single Phase, 50-60 Hz, 15
watts
• Size(Monitor):178mmx
137mm x 95mm
• Weight(Monitor):1.02kg
(single channel), 1.05kg
(double channel)
For more information, request
Catalog 1309085-2
Application Tooling
93
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Application Tooling (Continued)
This fully-automatic, PC-
controlled leadmaker can be
equipped with up to three
processing stations enabling
the crimping of both ends
of the wire, double-crimp
connections with three
different contacts, single-
ended seal applications,
tinning or ink-jet marking.
Features include ultra-short
conversions times, easy-to-
use graphic-based TopWin
interface with multiple-
language capability, crimp
force analyzer with statistical
analysis, seal monitoring, and
integrated good/bad sorting.
For more information, request
Catalog 1307901.
Komax gamma 333 PC
Lead-Making Machine
LEAD MAKERS
The 433-S alpha offers
maximum flexibility for
applying seals to one or
both ends of the wire with
the corresponding terminal.
When equipped with the mci
711 crimp terminator and mci
761 seal applicator, the fully-
automated 433-S alpha forms
a highly compact system
with optimum accessibility.
Dynamic servo-drives provide
fine travel settings on all
motor axes and the wire
straightening unit with quick-
release lock and automatic
lead-in feature reduces wire
changeover time. The TopWin
software provides for fast,
simple data input.
For more information, request
Catalog 1307801.
Komax 433-S alpha
Lead-Making Machine
The AMPOMATOR System III
Leadmaker is designed for
the demands of low-volume/
high mix manufacturing
and precision quality. This
leadmaker combines the best
wire processing capabilities
with new technologies in
terminal feeding and machine
set-up found in the System III
Applicator to offer signifi-
cant advantages for higher
throughput and efficiencies.
For more information, request
Catalog 1654956-5
AMPOMATOR System III
Leadmaker
Interchangeable applicators
for crimping products reeled
end-to-end (primarily open-
barrel terminals). Used in
bench and lead-making
machines; most designs can
be used, or adapted for use
with minor tooling changes,
dial-in settings for different
wire sizes and insulation
diameters. Mechanical or
air-powered feed systems,
depending on the product
applied.
For more information, request
Catalog 296393-2 and Instruction
Sheet 408-8039.
End-Feed Heavy-Duty
Miniature Applicators
(coded HDM)
APPLICATORS
The new EDGE counter
tracks wearable tool usage
for the most effective
maintenance planning.
The completely electronic
counter, with clear LCD
display, indicates cycles since
installation. By performing
maintenance at measured
intervals with pre-set limits,
operators avoid breakdowns
and rejects caused by tool
wear or mis-adjustment. A
wireless interface transfers
counters to a PC running
the optional Edge Counter
Software Pack.
The EDGE is standard on all
new applicators and can be
retrofitted to most existing
Tyco Electronics applicators.
For more information, request
Catalog 1773385..
EDGE Applicator Counter
Interchangeable applicators
for crimping products reeled
side-by-side on single or
dual carrier strips (primarily
closed-barrel terminals
and open-barrel contacts).
Similar design as the end-
feed version. All side-feed
applicators include a wire
stop to help correctly
position the wire end in the
crimping target area.
For more information, request
Catalog 296393-2 and Instruction
Sheet 408-8040.
Side-Feed Heavy-Duty
Miniature Applicators
(coded HDM)
89828
Application Tooling
AMP M Series
Pin and Socket Connectors
94
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Application Tooling (Continued)
Interchangeable applicators
for crimping products in
AMP-O-MATIC Stripper-
Crimper Machines. Consist
of separate ram and
lower tooling assemblies.
Similar dial-in settings for
different wire sizes and
insulation diameters as HDM
applicators. Available with
sensors for use with the
Crimp Quality Monitor.
For more information, request
Catalog 65004 (AMP-O-MATIC
Stripper-Crimper Machines),
Catalog 82275 [Crimp Quality
Monitor (CQM)].
Stripper-Crimper
Applicators (coded SCA)
89827
Semiautomatic bench
crimping machines that
also strip the wire, and
are therefore used for
terminating jacketed cable.
Feature manual precision
adjustment of crimp height,
keyed strip blades for faster,
more accurate setups, and
an efficient scrap removal
system. All adjustments can
be made from the front of
the machines without special
tools. Available with crimp
quality monitoring.
For more information, request
Catalog 65004, Video 198075,
Catalog 82275 [Crimp Quality
Monitor (CQM)], Video 198094.
AMP-O-MATIC Stripper-
Crimper Machines, Part
Nos. 1320895-1, -2
STRIPPER-CRIMPER MACHINES
The combination of the
Stripping Module with the
AMP 3K/40 and AMP 5K/40
Terminating Machines or
the AMP-O-LECTRIC Model
“G” Terminator provides an
economic and proficient
method of stripping the
wire and crimping terminals
on the same machine. The
module accepts End- and
Side-Feed HDM Applicators
(32-14 AWG) and operates
in three modes: crimp only,
strip only, or strip and crimp.
It can be installed on existing
machines in the field or
purchased as one unit from
the factory.
For more information, request
Catalog 1309085.
Stripping Module (for the
AMP 3K/40 and AMP
5K/40 Terminating
Machines and AMP-O-
LECTRIC Model “G”
Terminator on page 77)
12075-2
The Cosmic 30M is a high
precision, high speed
electrical wire stripper that
is very easy to operate. It’s
equipped with a four blade
system and an optional
gripper for more difficult
wires. There is a digital
display for the wire diameter
that can be set at 0.01 mm
increments.
For more information, request
Catalog 1773385-2.
Cosmic 30M Wire Strip-
ping Machine, 5-528367-0
The compact, lightweight,
benchtop Cosmic 927R was
designed and developed
to reliably strip various
insulation materials and
micro-cable. From conductor
diameter 36 to 10 AWG, the
stripping diameter display
can be set to within 0.1 mm
increments.
For more information, request
Catalog 1773385-4.
Cosmic 927R Micro-Cable
Stripper
Application Tooling
95
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Tooling Numerical Index
Tooling Numerical Index
45098 30
45638 42
45639 42
45740 42
58290 43
58305 30
58448 14
58495 31,34
58541 30
69186 42
69220 42
69222 42
69227 42
69248 42
69315 42
69360 42
69373 42
69656 39,40
69672 42
69690 39
69710 37,39,41,42
69875 30
90066 31,34
90067 31,34
90121 36
90122 36
90136 30
90140 38
90145 37
90225 31
90230 30
90231 30
90249 30
90250 30
90265 15
90302 14
90310 31
90331 31
90374 14
90405 15
90406 14
90716 31
91002 31
91016 78
91019 37
91067 19
91285 14
91911 39,40
91912 42
126195 19
189721 30,31,33,36,
37,39,40,43
189722 30,31,33,36,
37,39,40,43
189928 30,31,33,36,
37,39,40,43
Part No. Page No.
200893 30,31,32
217201 31,33
224155 38
305183 30,31,32,35,36,
37,39,41,42,59,60
318161 30,36,37,39,41,42
354940 39,40,42
356114 38
356119 38
356304 30,31,34,36,
37,39,41,43
356336 22
466321 31
466323 31,34
466324 31
466325 31
466326 31
466383 31
466422 14
466423 14
466585 31
466598 31
466741 34
466758 14
466900 14
466901 14
466906 31
466907 31,34
466908 31
466923 31
466942 31
466958 31
466963 14
466968 14
466979 31
567021 37
567036 14
567363 31
567364 31
567455 37
567801 14
567804 14
567849 14
567867 31
567947 31
601967 30,37
608651 21
608668 21
680114 34
680602 31
725840 34
811262 78,81
1016002 14
1616015 14
Part No. Page No.
Application Tooling/Technical
Document Cross Reference
Part No. Instruction Sheet
58541-1 408-4051
58495-1 408-9819
69710-1 408-2095
91550-1 408-7608
91521-1 408-7608
91519-1 408-7942
91019-3 408-7276
91067-2 408-7508
189721-2 408-5862
189722-2 408-5862
305183 408-1216
Tooling Numerical Index
AMP M Series
Pin and Socket Connectors
96
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Technical Documents
The following is a list of technical documents that provide specifications, applica-
tion and performance data for M Series connectors, contacts, tooling and hardware.
Product Specifications describe technical performance characteristics and verifica-
tion tests. They are intended for the Design, Component and Quality Engineer.
108-10001 M Series Connectors
108-10024 CPC Connectors
108-10037 Contacts, Type XII
108-10039 Type II Contacts
108-10040 Metal-Shell CPC Connectors
108-10042 Type III+ Contacts
108-10108 Type I Contacts
108-12011 Subminiature COAXICON Contacts
108-12021 Miniature COAXICON Contacts
Application Specifications describe requirements for using the product in its
intended application and/or crimping information. They are intended for the
Packaging and Design Engineer and the Machine Setup Person.
114-10000 Contacts, Size 20 DF
114-10004 Type III+ Contacts, Application of
114-10005 Type XII Contacts, Application of
114-10026 Type II Contacts
114-10038 CPC Connectors
Instruction Sheets provide instructions for assembling or applying the product.
They are intended for the Manufacturing Assembler or Operator.
408-1379 Selection Charts for Multimate Pin and Socket Contacts
408-7053 Selection Chart for Type I Pin and Socket Contacts
408-1770 Selection Chart for Miniature COAXICON Contacts
408-7170 6, 14, 20 and 41 Position M Series Connectors
408-7177 21 and 26 Position M Series Connectors
408-7161 34 and 50 Position and 20 Position (High Voltage) M Series Connectors
408-7164 75 and 104 Position M Series Connectors
408-7005 104 CF Position M Series Connectors
408-7293 160 CF Position M Series Connectors
408-7105 14, 20, 26 and 41 Position M Series Connector Kits
408-7107 34 and 50 Position M Series Connector Kits
408-7730 34, 50, 75 and 104 Position M Series Connector Kits
408-7108 75 and 104 Position M Series Connector Kits
408-7048 15 Position (Mixed) M Series Connectors
408-7455 29 Position (Mixed) M Series Connectors
408-6800 Shield Kit 208783-1 for 104 Position M Series Connector
408-7485 Press-Fit Jackscrews for M Series Connectors
408-7066 Locking Springs for 14, 20, 21, 26 and 41 Position M Series Connectors
408-7067 Locking Springs for 34 and 50 Position M Series Connectors
408-7055 Corner Guide Pins and Sockets for 34 and 50 Position M Series
Connectors
408-7056 Corner Guide Pins and Sockets for 75 and 104 Position M Series
Connectors
408-7121 Guide Pins and Sockets for 104 CF Position M Series Connectors
408-7013 Pin Hoods for M Series Connectors
Technical Documents
97
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Technical Documents (Continued)
Instruction Sheets provide instructions for assembling or applying the product.
They are intended for the Manufacturing Assembler or Operator. (Continued)
408-7094 Pin Hoods w/Mounting Flange for 34 and 50 Position M Series
Connectors
408-7103 Pin Hoods w/Mounting Flange for 41 Position M Series Connectors
408-7095 Pin Hoods w/Mounting Flange for 75 Position M Series Connectors
408-9731 M Series V.35 Cable Connector Kits
408-7089 Pin Hoods, Closed-End, for 104 CF Position M Series Connectors
408-1238 Shields (Long) for 34 and 50 Position M Series Connectors
408-1197 Shields (Short) for 34 and 50 Position M Series Connectors
408-1298 Shields, 180° (Long) for 14, 20, 26, 34 and 50 Position M Series
Connectors
408-1312 Shields, 180° (Short) for 14, 20, 26, 34 and 50 Position M Series
Connectors
408-1296 Shields, 90° (Long) for 14, 20, 26, 34 and 50 Position M Series
Connectors
408-1297 Shields, 90° (Short) for 14, 20, 26, 34 and 50 Position M Series
Connectors
408-7026 Shields, 90° (Short) for 21 and 41 Position M Series Connectors
408-1192 Shields, 180° (Long and Short) for 26 and 41 Position M Series
Connectors
408-7220 Shields, 180° and 90° (Long and Short) for 75 Position M Series
Connectors
408-1321 Shields, 90° (Short) for 104 Position M Series Connectors
408-7148 Shields, 90° and 45° (Long) for 104 CF Position M Series Connectors
408-7088 Shields, 45° (Short) for 104 CF Position M Series Connectors
408-7423 Shields, 45° (Short) for 160 CF Position M Series Connectors
408-7017 Strain Relief Clamps (Long) for 14 and 20 Position M Series Connectors
408-7018 Strain Relief Clamps (Long) for 26 Position M Series Connectors
408-1313 Strain Relief Clamps (Short) for 14, 20 and 26 Position M Series
Connectors
408-7012 Strain Relief Clamps (Long and Short) for 21 and 41 Position M Series
Connectors
408-7019 Strain Relief Clamps (Long) for 34 Position M Series Connectors
408-1317 Strain Relief Clamps (Short) for 34 and 50 Position M Series
Connectors
408-7216 Strain Relief Clamps (Long) for 75 Position M Series Connectors
408-1368 Strain Relief Clamps (Short) for 75 Position M Series Connectors
408-7020 Strain Relief Clamps (Long) for 50 and 104 Position M Series
Connectors
408-1322 Strain Relief Clamps (Short) for 104 Position M Series Connectors
408-1340 Keying Plug (Cylindrical) for Multimate Contact Cavities
408-6613 Application and Maintenance of AMP Hand Crimping Tool 90067
408-7414 Application and Maintenance of AMP Hand Crimping Tool 90225-2
408-7942 Application and Maintenance of AMP Hand Crimping Tool 90310-2
408-7773 Application and Maintenance of AMP Hand Crimping Tool 90331-1
408-7126 AMP Assembly Tool 91016 for Turnable Jackscrews
Technical Documents
AMP M Series
Pin and Socket Connectors
98
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Note: This numerical index lists all
cataloged parts by base no. only.
Complete part nos. (with prefixes
and/or suffixes) are shown on the
page(s) indicated.
Part No. Page Part No. Page
Part No. Page
201349 83
201350 83
201355 45
201356 45
201357 47
201358 47
201359 47
201360 86
201363 82
201364 82
201368 83
201369 82
201378 86
201384 86
201388 78
201389 78
201390 83
201413 78
201414 78
201443 85
201469 86
201501 78
201511 43
201512 43
201532 50
201540 81
201568 30
201570 30
201571 85
201576 85
201578 30
201580 30
201611 30
201613 30
201692 50
201766 88
201785 82
201786 82
201827 78
201828 78
201843 88
201845 88
201846 88
201847 88
201848 88
201849 88
201910 78
201911 78
201918 80
201921 80
201922 80
201923 80
201925 80
201926 80
202095 83
202096 83
202110 87
202119 83
202135 47
202165 83
50079 42
50080 42
51565 39, 40
66098 31
66099 31
66100 31
66101 31
66102 31
66103 31
66104 31
66105 31
66106 31
66107 31
66108 31
66109 31
66180 35
66181 35
66182 35
66183 35
66253 37
66254 37
66255 37
66256 37
66259 37
66260 37
66261 37
66262 37
66331 31
66332 31
66358 31
66359 31
66360 31
66361 31
66393 31
66394 31
66399 31
66400 31
66405 31
66406 31
66424 31
66425 31
66428 31
66429 31
66459 32
66460 32
66461 32
66468 32
66470 32
66471 32
66473 32
66563 31
66564 31
66565 31
66566 31
66597 31
66598 31
66601 31
66602 31
66740 37
66741 37
164159 34
164160 34
164161 34
164162 34
164163 34
164164 34
193990 38
193991 38
200277 47
200333 30
200336 30
200346 45
200389 81
200390 81
200512 47
200514 85
200517 85
200532 85
200686 88
200730 88
200821 89
200833 81
200835 81
200838 47
200867 78
200868 78
200870 78
200871 78
200874 79
200875 79
201037 49
201046 81
201047 81
201087 78
201088 78
201089 79
201092 79
201131 85
201142 42, 43
201143 43
201144 43
201145 43
201146 43
201165 86
201169 86
201182 88
201224 88
201227 86
201229 88
201237 88
201298 45
201302 47
201310 49
201311 49
201328 30
201330 30
201332 30
201334 30
201345 49
201346 83
Part Number Index
Part Number Index
99
AMP M Series
Pin and Socket Connectors
Catalog 82003 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514
Revised 06-08 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Hong Kong: 852-2735-1628
specified. Values in brackets are Specifications subject Mexico: 01-800-733-8926 Japan: 81-44-844-8013
www.tycoelectronics.com equivalent U.S. Customary Units. to change. C. America: 52-55-5-729-0425 UK: 44-141-810-8967
NOTE: All part numbers
are RoHS Compliant
Note: This numerical index lists all
cataloged parts by base no. only.
Complete part nos. (with prefixes
and/or suffixes) are shown on the
page(s) indicated.
Part No. Page
202169 87
202173 81
202174 81
202236 35
202237 35
202383 85
202394 82
202395 85
202417 36
202418 36
202421 36
202422 36
202434 82
202478 73
202479 73
202483 87
202507 30
202508 30
202515 74
202516 74
202711 85
202713 85
202725 30
202726 30
202757 45
202758 45
202798 87
202799 51,59
202800 51
203432 88
203535 77
203540 77
203618 77
203622 48,60
203743 82
203744 83
203908 75
203909 75
203956 47,60
203964 81
203966 81
203975 85
204087 85
204099 81
204219 30
204258 82
204814 77
205042 72
205043 72
205058 48
205156 56
205317 54
205359 57
205361 56
205505 56
2075507 54
205508 54
205509 54
205511 54
205512 54
Part No. Page
205514 56
205515 57
205516 72
205606 60
205628 60
205629 60
205630 60
205689 76
205690 76
205720 59
206508 89
207234 78
207235 78
207597 89
207619 81
212618 30
212810 64
213289 65
213300 68
213473 66
213513 65
213521 59
213522 68
213524 66
213550 67
213574 64
213684 70
213685 70
213753 68
213763 59
213799 47
213800 47
213801 47
213802 47
213803 71
213804 71
213805 71
213806 64
213807 64
213808 65
213809 66
213931 69
213932 69
221848 42
225088 39
226537 39, 40
328663 42
328664 42
328666 42
328667 42
329029 42
330478 42
330587 42
332056 39
332057 39, 40
788085 31
788088 31
Part Number Index (Continued)
Part Number Index
Tyco Electronics Corporation
Harrisburg, PA
82003 - Rev. 06/08 - OG3B
