LITE-ON SEMICONDUCTOR Sensitive Gate Sillicon Controlled Rectifiers Reverse Blocking Thyristors S1VM02-600A SCRs 1.5 AMPERES RMS 600 VOLTS TO-92 (TO-226AA) FEATURES Sensitive Gate Allows Triggering by Microcontrollers and Other Logic Circuits Blocking Voltage to 600 Volts On- State Current Rating of 1.5 Amperes RMS at Tc=80 High Surge Current Capability -- 15 Amperes Glass-Passivated Surface for Reliability and Uniformity TO-92 DIM. MIN. MAX. A 4.45 B 4.32 5.33 C 3.18 4.19 Pb-Free Package 4.70 D 1.15 1.39 E 2.42 2.66 F 12.7 ------ G 2.04 2.66 I 3.43 ----- All Dimensions in millimeter PIN ASSIGNMENT 1 Cathode 2 Gate 3 Anode MAXIMUM RATINGS (Tj= 25 unless otherwise noticed) Rating Symbol Value Unit Peak Repetitive Off- State Voltage (TJ= -40 to 110, Sine Wave, 50 to 60 Hz; Gate Open) VDRM, VRRM 600 Volts On-State RMS Current (TC = 80) 180 Conduction Angles IT(RMS) 1.5 Amps ITSM 15 Amps It 0.9 As PGM 0.5 Watt PG(AV) 0.1 Watt IGM 0.2 Amp VGRM 5.0 Volts TJ -40 to +110 Tstg -40 to +150 Peak Non-Repetitive Surge Current TA=25 (1/2 Cycle, Sine Wave, 60 Hz, TJ = 25) Circuit Fusing Consideration (t = 8.3 ms) Forward Peak Gate Power (TA = 25, Pulse Width 1.0 us) Forward Average Gate Power (TA = 25, t = 8.3 ms) Forward Peak Gate Current (TA = 25, Pulse Width1.0 us) Reverse Peak Gate Voltage (TA = 25, Pulse Width 1.0 ms) Operating Junction Temperature Range @ Rate VRRM and VDRM Storage Temperature Range Notice: (1) VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded 2 2 Rev. 2, Oct-2010, KTXD16 RATING AND CHARACTERISTIC CURVES S1VM02-600A THERMAL CHARACTERISTICS Characteristic Thermal Resistance - Junction to Case - Junction to Ambient Maximum Lead Temperature for Soldering Purposes 1/16" from Case for 10 Seconds Symbol Value Unit RthJC RthJA 50 160 /W TL 260 ELECTRICAL CHARACTERISTICS (TJ=25unless otherwise noted) Characteristics Symbol Min Typ Max Unit IDRM IRRM ------- ------- 10 200 uA VTM ---- 1.2 1.7 Volts OFF CHARACTERISTICS Peak Reptitive Forward or Reverse Blocking Current (VAK=Rated VDRM and VRRM; RGK =1K Ohms) TJ=25 TJ=110 ON CHARACTERISTICS Peak Forward On-State Voltage @TA=25 (ITM= 3.0A Peak, Pulse Width 1.0 ms, Duty Cycle 1%) Gate Trigger Current (VAK = 6.0 Vdc; RL = 100 Ohms) TJ=25 TJ=-40 IGT ------- 30 ---- 200 500 uA Holding Current (VAK = 12 V, Gate Open, Initiating Current = 200 mA) TJ= 25 TJ=-40 IH ------- 2.0 ---- 5.0 10 mA Gate Trigger Voltage (VD = 7 V; RL =100 Ohms) TJ= 25 TJ=-40 VGT ------- ------- 0.8 1.2 Volts VGD 0.1 ---- ---- Volts dv/dt ---- 25 Gate Non-Trigger Voltage (Pulse Width = 1.0ms, Duty Cycle 1%) VAK = 12 vdc, Gate Open) DYNAMIC CHARACTERISTICS Critical Rate of Rise of Off-State Voltage (VD=Rated VDRM,Exponential Waveform, RGK=1K Ohms, TJ=110 (1) RGK Current not included in measurement. ---- V/us IT ,INSTANTANEOUS ON-STATE CURRENT (AMP) RATING AND CHARACTERISTIC CURVES S1VM02-600A 10 TJ=25 TJ=125 1 0.1 0.5 1 1.5 2 VT ,INSTANTANEOUS ON-STATE VOLTAGE(VOLT) Figure 1.On-State Characteristics 2.5 RATING AND CHARACTERISTIC CURVES S1VM02-600A 0.8 VGT, GATE TRIGGER VOLTAGE IGT, GATE TRIGGER CURRENT 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 -40 -20 0 20 40 60 80 0.7 0.6 0.5 0.4 -40 100 -20 TJ JUNCTION TEMPERATURE() Figure 2. Typical IGT versus TJ 20 40 60 80 100 0.5 0.5 IL, LATCHING CURRENT IH, HOLDING CURRENT 0.6 0.4 0.3 0.2 0.1 0 -40 -20 0 20 40 60 80 100 0.4 0.3 0.2 0.1 -40 TJ JUNCTION TEMPERATURE() Figure 4. Typical IH versus TJ 1.2 1 0.8 0.6 0.4 0.2 0 0 10 20 30 40 50 60 70 80 90 100 110 TC, CASE TEMPERATURE() Figure 6. On-State Current Derating Curve -20 0 20 40 60 80 100 TJ JUNCTION TEMPERATURE() Figure 5. Typical IL versus TJ P(AV) ,AVERAGE POWER DISSIPATION (WATTS) IT(RMS) ,RMS ON-STATE CURRENT (AMP) 0 TJ JUNCTION TEMPERATURE() Figure 3. Typical VGT versus TJ 1.2 1 0.8 TJ=25 0.6 TJ=125 0.4 0.2 0 0 0.2 0.4 0.6 0.8 1 IT(AV), AVERAGE ON-STATE CURRENT (AMP) Figure 7. Power Dissipation versus IT Legal Disclaimer Notice S1VM02-600A Important Notice and Disclaimer LSC reserves the right to make changes to this document and its products and specifications at any time without notice. Customers should obtain and confirm the latest product information and specifications before final design, purchase or use. LSC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does LSC assume any liability for application assistance or customer product design. LSC does not warrant or accept any liability with products which are purchased or used for any unintended or unauthorized application. No license is granted by implication or otherwise under any intellectual property rights of LSC. LSC products are not authorized for use as critical components in life support devices or systems without express written approval of LSC.