LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 LM4132 SOT-23 Precision Low Dropout Voltage Reference Check for Samples: LM4132 FEATURES DESCRIPTION * * * * * * The LM4132 family of precision voltage references performs comparable to the best laser-trimmed bipolar references, but in cost effective CMOS technology. The key to this break through is the use of EEPROM registers for correction of curvature, tempco, and accuracy on a CMOS bandgap architecture that allows package level programming to overcome assembly shift. The shifts in voltage accuracy and tempco during assembly of die into plastic packages limit the accuracy of references trimmed with laser techniques. 1 2 * * * * Output Initial Voltage Accuracy 0.05% Low Temperature Coefficient 10ppm/C Low Supply Current, 60A Enable Pin Allowing a 3A Shutdown Mode 20mA Output Current Voltage Options 1.8V, 2.048V, 2.5V, 3.0V, 3.3V, 4.096V Custom Voltage Options Available (1.8V to 4.096V) VIN Range of VREF + 400mV to 5.5V @ 10mA Stable with Low ESR Ceramic Capacitors SOT23-5 Package Unlike other LDO references, the LM4132 is capable of delivering up to 20mA and does not require an output capacitor or buffer amplifier. These advantages and the SOT23 packaging are important for space-critical applications. APPLICATIONS * * * * * * * * * * * Series references provide lower power consumption than shunt references, since they do not have to idle the maximum possible load current under no load conditions. This advantage, the low quiescent current (60A), and the low dropout voltage (400mV) make the LM4132 ideal for battery-powered solutions. Instrumentation & Process Control Test Equipment Data Acquisition Systems Base Stations Servo Systems Portable, Battery Powered Equipment Automotive & Industrial Precision Regulators Battery Chargers Communications Medical Equipment The LM4132 is available in five grades (A, B, C, D and E) for greater flexibility. The best grade devices (A) have an initial accuracy of 0.05% with a specified temperature coefficient of 10ppm/C or less, while the lowest grade parts (E) have an initial accuracy of 0.5% and a tempco of 30ppm/C. Typical Application Circuit Input 5V VIN CIN* LM4132 Enable Output 2.5V VREF * COUT EN GND *Note: The capacitor CIN is required and the capacitor COUT is optional. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2005-2013, Texas Instruments Incorporated LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Connection Diagram N/C 1 5 VREF GND 2 EN 3 4 VIN (Top View) See Package Number DBV0005A PIN DESCRIPTIONS Pin # Name Function 1 N/C No connect pin, leave floating 2 GND Ground 3 EN Enable pin 4 VIN Input supply 5 VREF Reference output These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Maximum Voltage on any input -0.3 to 6V Output short circuit duration Indefinite Power Dissipation (TA = 25C) (3) 350mW -65C to 150C Storage Temperature Range Lead Temperature (soldering, 10sec) 260C Vapor Phase (60 sec) 215C Infrared (15sec) 220C ESD Susceptibility (1) (2) (3) (4) (4) Human Body Model 2kV Absolute Maximum Ratings indicate limits beyond which damage may occur to the device. Operating Ratings indicate conditions for which the device is intended to be functional. For specifications, see Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by TJMAX (maximum junction temperature), J-A (junction to ambient thermal resistance) and TA (ambient temperature). The maximum power dissipation at any temperature is: PDissMAX = (TJMAX - TA) /J-A up to the value listed in the Absolute Maximum Ratings. J-A for SOT23-5 is 220C/W, TJMAX = 125C. The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Operating Ratings Maximum Input Supply Voltage 5.5V Maximum Enable Input Voltage VIN Maximum Load Current 20mA -40C to +125C Junction Temperature Range (TJ) 2 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Electrical Characteristics LM4132-1.8 (VOUT = 1.8V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (1) Typ (2) LM4132A-1.8 (A Grade - 0.05%) -0.05 0.05 LM4132B-1.8 (B Grade - 0.1%) -0.1 0.1 LM4132C-1.8 (C Grade - 0.2%) -0.2 0.2 LM4132D-1.8 (D Grade - 0.4%) -0.4 0.4 LM4132E-1.8 (E Grade - 0.5%) -0.5 0.5 LM4132A-1.8 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-1.8 60 100 EN = 0V 3 7 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 30 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 230 0.1 Hz to 10 Hz 170 VIN - VREF (2) (3) (4) (5) ppm / C 30 Supply Current in Shutdown VREF % 20 LM4132E-1.8 IQ_SD Unit Temperature Coefficient LM4132C-1.8 (1) (1) Output Voltage Initial Accuracy LM4132B-1.8 IQ Max Supply Current A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 3 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Electrical Characteristics LM4132-2.0 (VOUT = 2.048V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (1) Typ (2) LM4132A-2.0 (A Grade - 0.05%) -0.05 0.05 LM4132B-2.0 (B Grade - 0.1%) -0.1 0.1 LM4132C-2.0 (C Grade - 0.2%) -0.2 0.2 LM4132D-2.0 (D Grade - 0.4%) -0.4 0.4 LM4132E-2.0 (E Grade - 0.5%) -0.5 0.5 LM4132A-2.0 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-2.0 60 100 EN = 0V 3 7 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 30 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 175 0.1 Hz to 10 Hz 190 VIN - VREF (2) (3) (4) (5) 4 ppm / C 30 Supply Current in Shutdown VREF % 20 LM4132E-2.0 IQ_SD Unit Temperature Coefficient LM4132C-2.0 (1) (1) Output Voltage Initial Accuracy LM4132B-2.0 IQ Max Supply Current A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Electrical Characteristics LM4132-2.5 (VOUT = 2.5V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min Typ (1) (2) LM4132A-2.5 (A Grade - 0.05%) -0.05 0.05 LM4132B-2.5 (B Grade - 0.1%) -0.1 0.1 LM4132C-2.5 (C Grade - 0.2%) -0.2 0.2 LM4132D-2.5 (D Grade - 0.4%) -0.4 0.4 LM4132E-2.5 (E Grade - 0.5%) -0.5 0.5 LM4132A-2.5 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-2.5 60 100 EN = 0V 3 7 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 50 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 175 0.1 Hz to 10 Hz 240 VIN - VREF (2) (3) (4) (5) ppm / C 30 Supply Current in Shutdown VREF % 20 LM4132E-2.5 IQ_SD Unit Temperature Coefficient LM4132C-2.5 (1) (1) Output Voltage Initial Accuracy LM4132B-2.5 IQ Max Supply Current A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 5 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Electrical Characteristics LM4132-3.0 (VOUT = 3.0V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (1) Typ (2) LM4132A-3.0 (A Grade - 0.05%) -0.05 0.05 LM4132B-3.0 (B Grade - 0.1%) -0.1 0.1 LM4132C-3.0 (C Grade - 0.2%) -0.2 0.2 LM4132D-3.0 (D Grade - 0.4%) -0.4 0.4 LM4132E-3.0 (E Grade - 0.5%) -0.5 0.5 LM4132A-3.0 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-3.0 60 100 EN = 0V 3 7 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 70 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 175 0.1 Hz to 10 Hz 285 VIN - VREF (2) (3) (4) (5) 6 ppm / C 30 Supply Current in Shutdown VREF % 20 LM4132E-3.0 IQ_SD Unit Temperature Coefficient LM4132C-3.0 (1) (1) Output Voltage Initial Accuracy LM4132B-3.0 IQ Max Supply Current A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Electrical Characteristics LM4132-3.3 (VOUT = 3.3V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (1) Typ (2) LM4132A-3.3 (A Grade - 0.05%) -0.05 0.05 LM4132B-3.3 (B Grade - 0.1%) -0.1 0.1 LM4132C-3.3 (C Grade - 0.2%) -0.2 0.2 LM4132D-3.3 (D Grade - 0.4%) -0.4 0.4 LM4132E-3.3 (E Grade - 0.5%) -0.5 0.5 LM4132A-3.3 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-3.3 60 100 EN = 0V 3 7 VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 85 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 175 0.1 Hz to 10 Hz 310 VIN - VREF (2) (3) (4) (5) ppm / C 30 Supply Current in Shutdown VREF % 20 LM4132E-3.3 IQ_SD Unit Temperature Coefficient LM4132C-3.3 (1) (1) Output Voltage Initial Accuracy LM4132B-3.3 IQ Max Supply Current A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 7 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Electrical Characteristics LM4132-4.1 (VOUT = 4.096V) Limits in standard type are for TJ = 25C only, and limits in boldface type apply over the junction temperature (TJ) range of 40C to +125C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. Unless otherwise specified VIN = 5V and ILOAD = 0 Symbol VREF TCVREF / C (Note 6) Parameter Conditions Min (1) Typ (2) LM4132A-4.1 (A Grade - 0.05%) -0.05 0.05 LM4132B-4.1 (B Grade - 0.1%) -0.1 0.1 LM4132C-4.1 (C Grade - 0.2%) -0.2 0.2 LM4132D-4.1 (D Grade - 0.4%) -0.4 0.4 LM4132E-4.1 (E Grade - 0.5%) -0.5 0.5 LM4132A-4.1 0C TJ + 85C 10 -40C TJ +125C 20 20 20 -40C TJ +125C LM4132D-4.1 (1) (2) (3) (4) (5) 8 ppm / C 30 Supply Current 60 100 3 7 Supply Current in Shutdown EN = 0V VREF/VIN Line Regulation VREF + 400mV VIN 5.5V 100 VREF/ILOAD Load Regulation 0mA ILOAD 20mA 25 Long Term Stability (3) 1000 Hrs 50 Thermal Hysteresis (4) -40C TJ +125C 75 Dropout Voltage (5) ILOAD = 10mA 175 0.1 Hz to 10 Hz 350 VIN - VREF % 20 LM4132E-4.1 VREF Unit Temperature Coefficient LM4132C-4.1 IQ (1) Output Voltage Initial Accuracy LM4132B-4.1 IQ_SD Max A A ppm / V 120 ppm / mA ppm 400 mV VN Output Noise Voltage ISC Short Circuit Current 75 mA VIL Enable Pin Maximum Low Input Level 35 %VIN VIH Enable Pin Minimum High Input Level 65 VPP %VIN Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control. Typical numbers are at 25C and represent the most likely parametric norm. Long term stability is VREF @25C measured during 1000 hrs. Thermal hysteresis is defined as the change in +25C output voltage before and after cycling the device from (-40C to 125C). Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value measured with a 5V input. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Typical Performance Characteristics for 1.8V Output Voltage vs Temperature Load Regulation 1.804 1.8010 1.803 OUTPUT VOLTAGE (V) 1.8005 OUTPUT VOLTAGE (V) 1.802 5 TYPICAL UNITS 1.801 1.800 1.799 1.798 1.8000 1.7995 25oC 1.7990 -40oC 1.7985 1.797 1.796 -40 125oC -20 0 20 40 60 80 100 120 1.7980 0 TEMPERATURE (oC) 2 4 6 8 10 12 14 16 18 20 LOAD CURRENT (mA) Figure 1. Figure 2. Line Regulation 0.1-10Hz Noise 1.8020 OUTPUT VOLTAGE (V) 1.8015 1.8010 125oC 1.8005 25oC 1.8000 1.7995 -40oC 1.7990 1.7985 1.7990 2.2 2.7 3.2 3.7 4.2 4.7 5.2 INPUT VOLTAGE (V) Figure 3. Figure 4. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 0 POWER SUPPLY REJECTION (dB) OUTPUT NOISE VOLTAGE (PV/rt(Hz)) 16 14 NO COUT 12 10 8 6 4 2 0 10 100 1k 10k -10 NO COUT -20 -30 -40 -50 -60 -70 COUT = 0.1 PF -80 -90 10 100 1k 10k 100k 1M FREQUENCY (Hz) FREQUENCY (Hz) Figure 5. Figure 6. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 9 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics for 2.048V Output Voltage vs Temperature Load Regulation 2.050 2.052 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 2.051 2.050 5 TYPICAL UNITS 2.049 2.048 2.047 2.049 2.048 25oC -40oC 2.047 125oC 2.046 2.046 2.045 -50 -25 0 25 50 75 100 2.045 0 125 4 8 12 16 20 LOAD CURRENT (mA) TEMPERATURE (oC) Figure 7. Figure 8. Line Regulation 0.1 - 10 Hz Noise 2.052 OUTPUT VOLTAGE (V) 2.051 125oC 2.050 25oC 2.049 2.048 -40oC 2.047 2.046 2.5 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) Figure 9. Figure 10. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 0 POWER SUPPLY REJECTION (dB) OUTPUT NOISE VOLTAGE (PV/rt(Hz)) 16 14 NO COUT 12 10 8 6 4 2 0 10 -20 -30 NO COUT -40 -50 -60 -70 COUT = 0.1 PF -80 100 1k 10k FREQUENCY (Hz) 10 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 11. 10 -10 Figure 12. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Typical Performance Characteristics for 2.5V Output Voltage vs Temperature Load Regulation 2.504 2.503 5 TYPICAL UNITS OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 2.503 2.502 2.501 2.500 2.499 2.502 -40oC 2.501 2.500 125oC 2.499 2.498 2.497 -50 25oC -25 0 25 50 75 100 2.498 0 125 4 o 8 12 16 TEMPERATURE ( C) LOAD CURRENT (mA) Figure 13. Figure 14. Line Regulation 0.1 - 10 Hz Noise 20 2.502 OUTPUT VOLTAGE (V) 125oC 2.501 2.500 25oC -40oC 2.499 2.498 2.497 3.0 3.5 4.0 4.5 5.0 5.5 INPUT VOLTAGE (V) Figure 15. Figure 16. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 0 POWER SUPPLY REJECTION (dB) OUTPUT NOISE VOLTAGE (PV/rt(Hz)) 32 28 NO COUT 24 20 16 12 8 4 0 -10 NO COUT -20 -30 -40 -50 -60 COUT = 0.1 PF -70 -80 10 100 1k 10k FREQUENCY (Hz) 10 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 17. Figure 18. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 11 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics for 3.0V Output Voltage vs Temperature Load Regulation 3.006 3.0020 3.005 3.0015 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 3.004 3.003 3.002 5 TYPICAL UNITS 3.001 3 2.999 3.0010 3.0005 125oC 3.0000 2.9995 25oC 2.9990 2.998 2.9985 2.997 2.9980 2.996 -40 -20 0 20 40 60 -40oC 2.9975 80 100 120 0 2 o TEMPERATURE ( C) 4 6 8 10 12 14 16 18 20 LOAD CURRENT (mA) Figure 19. Figure 20. Line Regulation 0.1-10 Hz Noise 3.0020 OUTPUT VOLTAGE (V) 3.0015 125oC 3.0010 3.0005 25oC 3.0000 2.9995 2.9990 -40oC 2.9985 2.9980 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 INPUT VOLTAGE (V) Figure 21. Figure 22. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 0 POWER SUPPLY REJECTION (dB) OUTPUT NOISE VOLTAGE PV (Hz)) 30 25 NO COUT 20 15 10 5 0 10 100 1k NO COUT -20 -30 -40 -50 -60 -70 COUT = 0.1 PF -80 10 10k FREQUENCY (Hz) 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 23. 12 -10 Figure 24. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Typical Performance Characteristics for 3.3V Output Voltage vs Temperature Load Regulation 3.305 3.3005 3.304 3.3000 5 TYPICAL UNITS 3.302 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 3.303 3.301 3.3 3.299 3.298 3.297 3.2990 25oC 3.2985 125oC 3.2980 3.296 3.295 -40 -40oC 3.2995 -20 0 20 40 60 80 100 120 3.2975 0 TEMPERATURE (oC) 2 4 6 8 10 12 14 16 18 20 LOAD CURRENT (mA) Figure 25. Figure 26. Line Regulation 0.1-10 Hz Noise 3.3010 OUTPUT VOLTAGE (V) 3.3008 25oC 3.3006 3.3004 3.3002 125oC 3.3000 -40oC 3.2998 3.2996 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5 INPUT VOLTAGE (V) Figure 27. Figure 28. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency 0 POWER SUPPLY REJECTION (dB) OUTPUT NOISE VOLTAGE PV (Hz)) 30 25 NO COUT 20 15 10 5 0 10 100 1k -10 -30 -40 -50 COUT = 0.1 PF -60 -70 -80 -90 10 10k NO COUT -20 100 1k 10k FREQUENCY (Hz) FREQUENCY (Hz) Figure 29. Figure 30. 100k 1M Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 13 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics for 4.096V Output Voltage vs Temperature Load Regulation 4.104 4.098 -40oC 5 TYPICAL UNITS OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 4.102 4.100 4.098 4.096 4.094 4.097 4.096 125oC 4.095 25oC 4.094 4.092 4.090 -50 -25 0 25 50 75 100 4.093 0 125 4 8 12 16 TEMPERATURE ( C) LOAD CURRENT (mA) Figure 31. Figure 32. Line Regulation 0.1 - 10 Hz Noise o 20 4.100 OUTPUT VOLTAGE (V) 4.099 4.098 125oC 4.097 4.096 4.095 -40oC 4.094 25oC 4.093 4.092 4.5 4.7 4.9 5.1 5.3 5.5 INPUT VOLTAGE (V) Figure 33. Figure 34. Output Voltage Noise Spectrum Power Supply Rejection vs Frequency POWER SUPPLY REJECTION RATIO (dB) OUTPUT NOISE VOLTAGE (PV/rt(Hz)) 32 28 NO COUT 24 20 16 12 8 4 0 10 100 1k 10k FREQUENCY (Hz) -10 NO COUT -20 -30 -40 -50 -60 COUT = 0.1 PF -70 -80 10 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 35. 14 0 Figure 36. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 Typical Performance Characteristics Dropout vs Load to 0.5% Accuracy Supply Current vs Input Voltage 100 450 VREF = 2.048V 400 VDROPOUT (mV) SUPPLY CURRENT (PA) 2.048V 350 300 250 200 150 2.5V 100 4.096V 50 0 2 7 12 17 80 125oC 60 25oC 40 -40oC 20 0 0.5 22 1.5 ILOAD (mA) 2.5 3.5 4.5 INPUT VOLTAGE (V) Figure 37. Figure 38. Enable Threshold Voltage and Hysteresis Shutdown IQ vs Temperature 5.0 2.5 4.5 VEN (V) IQ SHUTDOWN (PA) 3 VIL 2 1.5 VIH 1 4.0 3.5 3.0 2.5 0.5 2.0 0 2 2.5 3 3.5 4 4.5 5 -40 50 75 Typical Long Term Stability Ground Current vs Load Current 100 125 85 1 TYPICAL UNIT FROM EACH VOLTAGE OPTION 80 GROUND CURRENT (PA) DRIFT (ppm) 25 Figure 40. 100 50 150 -50 -100 75 70 65 60 -150 -200 0 Figure 39. 200 0 -25 TEMPERATURE (oC) VIN (V) 150 5.5 0 100 200 300 400 500 600 700 800 900 1000 TIME (Hours) 55 0 5 10 15 20 LOAD CURRENT (mA) Figure 41. Figure 42. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 15 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Typical Thermal Hysteresis Turn-On Transient Response 45 Temperature Range -40oC < TJ < 125oC after 8 thermal cycles 40 FREQUENCY 35 30 25 20 15 10 5 0 0 25 50 75 100 125 150 200 HYSTERESIS (ppm) 16 Figure 43. Figure 44. Load Transient Response ILOAD = 0 to 10mA Line Transient Response VIN = 4V to 5.5V Figure 45. Figure 46. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 APPLICATION INFORMATION THEORY OF OPERATION The foundation of any voltage reference is the band-gap circuit. While the reference in the LM4132 is developed from the gate-source voltage of transistors in the IC, principles of the band-gap circuit are easily understood using a bipolar example. For a detailed analysis of the bipolar band-gap circuit, please refer to Application Note AN-56. SUPPLY AND ENABLE VOLTAGES To ensure proper operation, VEN and VIN must be within a specified range. An acceptable range of input voltages is: VIN > VREF + 400mV (ILOAD 10mA) (1) The enable pin uses an internal pull-up current source (IPULL_UP 2A) that may be left floating or triggered by an external source. If the part is not enabled by an external source, it may be connected to VIN. An acceptable range of enable voltages is given by the enable transfer characteristics. See the Electrical Characteristics section and Enable Transfer Characteristics figure for more detail. Note, the part will not operate correctly for VEN > VIN. COMPONENT SELECTION A small ceramic (X5R or X7R) capacitor on the input must be used to ensure stable operation. The value of CIN must be sized according to the output capacitor value. The value of CIN must satisfy the relationship CIN COUT. When no output capacitor is used, CIN must have a minimum value of 0.1F. Noise on the power-supply input may affect the output noise. Larger input capacitor values (typically 4.7F to 22F) may help reduce noise on the output and significantly reduce overshoot during startup. Use of an additional optional bypass capacitor between the input and ground may help further reduce noise on the output. With an input capacitor, the LM4132 will drive any combination of resistance and capacitance up to VREF/20mA and 10F respectively. The LM4132 is designed to operate with or without an output capacitor and is stable with capacitive loads up to 10F. Connecting a capacitor between the output and ground will significantly improve the load transient response when switching from a light load to a heavy load. The output capacitor should not be made arbitrarily large because it will effect the turn-on time as well as line and load transients. While a variety of capacitor chemistry types may be used, it is typically advisable to use low esr ceramic capacitors. Such capacitors provide a low impedance to high frequency signals, effectively bypassing them to ground. Bypass capacitors should be mounted close to the part. Mounting bypass capacitors close to the part will help reduce the parasitic trace components thereby improving performance. SHORT CIRCUITED OUTPUT The LM4132 features indefinite short circuit protection. This protection limits the output current to 75mA when the output is shorted to ground. TURN ON TIME Turn on time is defined as the time taken for the output voltage to rise to 90% of the preset value. The turn on time depends on the load. The turn on time is typically 33.2s when driving a 1F load and 78.8s when driving a 10F load. Some users may experience an extended turn on time (up to 10ms) under brown out conditions and low temperatures (-40C). THERMAL HYSTERESIS Thermal hysteresis is defined as the change in output voltage at 25C after some deviation from 25C. This is to say that thermal hysteresis is the difference in output voltage between two points in a given temperature profile. An illustrative temperature profile is shown in Figure 47. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 17 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com 125oC VREF1 25oC Time VREF2 -40oC Figure 47. Illustrative Temperature Profile This may be expressed analytically as the following: VHYS = lVREF1 - VREF2l x 106 ppm VREF Where * * * * * VHYS = Thermal hysteresis expressed in ppm VREF = Nominal preset output voltage VREF1 = VREF before temperature fluctuation VREF2 = VREF after temperature fluctuation. The LM4132 features a low thermal hysteresis of 75 ppm (typical) from -40C to 125C after 8 temperature cycles. (2) TEMPERATURE COEFFICIENT Temperature drift is defined as the maximum deviation in output voltage over the operating temperature range. This deviation over temperature may be illustrated as shown in Figure 48. Temperature Change in Output Voltage Voltage VREF_MAX VREF_MIN Temperature Range Figure 48. Illustrative VREF vs Temperature Profile Temperature coefficient may be expressed analytically as the following: TD = (VREF_MAX - VREF_MIN) VREF x 'T x 106 ppm (3) TD = Temperature drift VREF = Nominal preset output voltage VREF_MIN = Minimum output voltage over operating temperature range VREF_MAX = Maximum output voltage over operating temperature range T = Operating temperature range. The LM4132 features a low temperature drift of 10ppm (max) to 30ppm (max), depending on the grade. 18 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 LONG TERM STABILITY Long-term stability refers to the fluctuation in output voltage over a long period of time (1000 hours). The LM4132 features a typical long-term stability of 50ppm over 1000 hours. The measurements are made using 5 units of each voltage option, at a nominal input voltage (5V), with no load, at room temperature. EXPRESSION OF ELECTRICAL CHARACTERISTICS Electrical characteristics are typically expressed in mV, ppm, or a percentage of the nominal value. Depending on the application, one expression may be more useful than the other. To convert one quantity to the other one may apply the following: ppm to mV error in output voltage: VREF x ppmERROR 103 = VERROR Where * VREF is in volts (V) and VERROR is in milli-volts (mV). (4) Bit error (1 bit) to voltage error (mV): VREF 2n x 103 = VERROR (5) VREF is in volts (V), VERROR is in milli-volts (mV), and n is the number of bits. mV to ppm error in output voltage: VERROR VREF x 103 = ppmERROR Where * VREF is in volts (V) and VERROR is in milli-volts (mV). (6) Voltage error (mV) to percentage error (percent): VERROR VREF x 0.1 = Percent_Error Where * VREF is in volts (V) and VERROR is in milli-volts (mV). (7) PRINTED CIRCUIT BOARD and LAYOUT CONSIDERATIONS References in SOT packages are generally less prone to PC board mounting than devices in Small Outline (SOIC) packages. To minimize the mechanical stress due to PC board mounting that can cause the output voltage to shift from its initial value, mount the reference on a low flex area of the PC board, such as near the edge or a corner. The part may be isolated mechanically by cutting a U shape slot on the PCB for mounting the device. This approach also provides some thermal isolation from the rest of the circuit. Bypass capacitors must be mounted close to the part. Mounting bypass capacitors close to the part will reduce the parasitic trace components thereby improving performance. Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 19 LM4132 SNVS372C - AUGUST 2005 - REVISED APRIL 2013 www.ti.com Typical Application Circuits V REF Input VIN VREF C OUT CIN R R +5V -VREF LM4132 -5V Enable R/2 EN GND 4.7 F < C OUT < 10 F Figure 49. Voltage Reference with Complimentary Output +5V Input VIN VREF VREF_FORCE CIN 0.1 F LM4132 Enable EN 100 k: VREF_SENSE GND Figure 50. Precision Voltage Reference with Force and Sense Output Input VIN Output VREF CIN R1 500: LM4132 0.1 F Enable EN RSET GND I OUT IOUT = (VREF/(R1 + RSET)) + IGND IGND RL 1 k: Figure 51. Programmable Current Source 20 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 LM4132 www.ti.com SNVS372C - AUGUST 2005 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision B (April 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 20 Submit Documentation Feedback Copyright (c) 2005-2013, Texas Instruments Incorporated Product Folder Links: LM4132 21 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM4132AMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AA LM4132AMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BA LM4132AMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CA LM4132AMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DA LM4132AMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EA LM4132AMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FA LM4132AMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FA LM4132AMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AA LM4132AMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BA LM4132AMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CA LM4132AMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DA LM4132AMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EA LM4132AMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FA LM4132BMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AB LM4132BMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BB LM4132BMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CB LM4132BMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DB Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) LM4132BMF-3.3/NOPB Package Type Package Pins Package Drawing Qty ACTIVE SOT-23 DBV 5 1000 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EB (4/5) LM4132BMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FB LM4132BMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FB LM4132BMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AB LM4132BMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BB LM4132BMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CB LM4132BMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DB LM4132BMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EB LM4132BMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FB LM4132CMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AC LM4132CMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BC LM4132CMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CC LM4132CMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DC LM4132CMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EC LM4132CMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FC LM4132CMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FC LM4132CMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AC LM4132CMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BC LM4132CMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CC Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM4132CMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DC LM4132CMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EC LM4132CMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FC LM4132DMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AD LM4132DMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BD LM4132DMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CD LM4132DMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DD LM4132DMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4ED LM4132DMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FD LM4132DMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AD LM4132DMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BD LM4132DMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CD LM4132DMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DD LM4132DMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4ED LM4132DMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FD LM4132EMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AE LM4132EMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BE LM4132EMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CE Addendum-Page 3 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 1-Nov-2013 Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM4132EMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DE LM4132EMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EE LM4132EMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FE LM4132EMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AE LM4132EMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BE LM4132EMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CE LM4132EMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DE LM4132EMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EE LM4132EMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FE (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 4 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 1-Nov-2013 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 5 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM4132AMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 LM4132AMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 LM4132AMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 LM4132AMF-3.0/NOPB SOT-23 DBV 5 1000 LM4132AMF-3.3/NOPB SOT-23 DBV 5 LM4132AMF-4.1 SOT-23 DBV LM4132AMF-4.1/NOPB SOT-23 DBV LM4132AMFX-1.8/NOPB SOT-23 W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132AMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132AMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132AMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132AMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132AMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132BMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132BMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132BMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132BMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132BMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM4132BMF-4.1 SOT-23 DBV 5 1000 178.0 8.4 LM4132BMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 LM4132BMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 LM4132BMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 LM4132BMFX-2.5/NOPB SOT-23 DBV 5 3000 LM4132BMFX-3.0/NOPB SOT-23 DBV 5 LM4132BMFX-3.3/NOPB SOT-23 DBV 5 LM4132BMFX-4.1/NOPB SOT-23 DBV W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-4.1 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132CMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132DMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4132EMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LM4132EMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4132AMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132AMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132AMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132AMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132AMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132AMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132AMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 Pack Materials-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4132BMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132BMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132BMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132CMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132CMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132DMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132DMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132EMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LM4132EMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132EMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 4 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4132EMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132EMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132EMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LM4132EMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 5 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated