LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 LM120/LM320-N Series 3-Terminal Negative Regulators Check for Samples: LM120, LM320-N FEATURES 1 * * * * 2 * * * Preset Output Voltage Error Less than 3% Preset Current Limit Internal Thermal Shutdown Operates with Input-Output Voltage Differential down to 1V Excellent Ripple Rejection Low Temperature Drift Easily Adjustable to Higher Output Voltage DESCRIPTION The LM120 series are three-terminal negative regulators with a fixed output voltage of -5V, -12V, and -15V, and up to 1.5A load current capability. Where other voltages are required, the LM137 and LM137HV series provide an output voltage range of -1.2V to -47V. The LM120 need only one external component--a compensation capacitor at the output, making them easy to apply. Worst case specifications on output voltage deviation due to any combination of line, load or temperature variation assure satisfactory system operation. Exceptional effort has been made to make the LM120 Series immune to overload conditions. The regulators have current limiting which is independent of temperature, combined with thermal overload protection. Internal current limiting protects against momentary faults while thermal shutdown prevents junction temperatures from exceeding safe limits during prolonged overloads. Although primarily intended for fixed output voltage applications, the LM120 Series may be programmed for higher output voltages with a simple resistive divider. The low quiescent drain current of the devices allows this technique to be used with good regulation. Table 1. LM120 Series Packages and Power Capability Device LM120/LM320N LM320-N Package Rated Power Dissipation Design Load Current TO-3 (NDS) 20W 1.5A TO (NDT) 2W 0.5A TO-220 (NDE) 15W 1.5A Typical Applications Figure 1. Dual Trimmed Supply *Required if regulator is separated from filter capacitor by more than 3 inches. For value given, capacitor must be solid tantalum. 25 F aluminum electrolytic may be substituted. Required for stability. For value given, capacitor must be solid tantalum. 25 F aluminum electrolytic may be substituted. Values given may be increased without limit. For output capacitance in excess of 100 F, a high current diode from input to output (1N4001, etc.) will protect the regulator from momentary input shorts. Figure 2. Fixed Regulator 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1998-2013, Texas Instruments Incorporated LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS-5 VOLT REGULATORS (1) (2) (3) Power Dissipation Internally Limited -25V Input Voltage Input-Output Voltage Differential 25V (4) Junction Temperatures -65C to +150C Storage Temperature Range Lead Temperature (Soldering, 10 sec.) 300C Plastic 260C (1) (2) (3) Refer to RETS120-5H drawing for LM120H-5.0 or RETS120-5K drawing for LM120-5K military specifications. For -5V 3 amp regulators, see LM145 data sheet. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. (4) LM120K-5.0 AND LM320K-5.0 ELECTRICAL CHARACTERISTICS (1) Metal Can Package Order Numbers LM120K-5.0 (TO-3) LM320K-5.0 (TO-3) Design Output Current (ID) Device Dissipation (PD) Parameter Output Voltage Conditions Units 1.5A 20W (2) TJ = 25C, VIN =10V, Min Typ Max Min Typ Max -5.1 -5 -4.9 -5.2 -5 -4.8 V 10 25 10 40 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -25 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 10V, (3) 54 -7 64 50 -25 54 75 -7 64 60 V dB 100 mV -4.75 V 5 mA ILOAD ID Output Voltage, (2) -7.5V VIN VMAX, -5.20 -4.80 -5.25 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 5 mA ILOAD ID Output Noise Voltage TA = 25C, CL = 1 F, IL = 5 mA, 1 2 1 2 mA 0.1 0.4 0.1 0.4 mA 0.1 0.4 0.1 0.4 mA 150 V 150 VIN = 10V, 10 Hz f 100 kHz Long Term Stability 5 50 5 50 mV Thermal Resistance (1) (2) (3) 2 Junction to Case 3 3 C/W Junction to Ambient 35 35 C/W For -5V 3 amp regulators, see LM145 data sheet. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 LM120H-5.0 ELECTRICAL CHARACTERISTICS (1) Metal Can Package Order Numbers LM120H-5.0 (TO) Design Output Current (ID) Device Dissipation (PD) 0.5A 2W Parameter Output Voltage Conditions (2) Units Min Typ Max -5.1 -5 -4.9 V 10 25 mV -7 V 50 mV -4.80 V 1 2 mA VMIN VIN VMAX 0.05 0.4 mA 5 mA ILOAD ID 0.04 0.4 mA TJ = 25C, VIN =10V, ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -25 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 10V, (3) 54 64 30 dB 5 mA ILOAD ID Output Voltage, (4) -7.5V VIN VMAX, -5.20 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change Output Noise Voltage TA = 25C, CL = 1 F, IL = 5 mA, 150 V 5 mV VIN = 10V, 10 Hz f 100 kHz Long Term Stability Thermal Resistance (1) (2) (3) (4) (5) Junction to Case (5) C/W Junction to Ambient (5) C/W For -5V 3 amp regulators, see LM145 data sheet. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Thermal resistance of typically 85C/W (in 400 linear feet air flow), 224C/W (in static air) junction to ambient, of typically 21C/W junction to case. ABSOLUTE MAXIMUM RATINGS-12 VOLT REGULATORS (1) (2) Power Dissipation Internally Limited -35V Input Voltage Input-Output Voltage Differential 30V (3) Junction Temperatures -65C to +150C Storage Temperature Range Lead Temperature (Soldering, 10 sec.) (1) (2) (3) 300C Refer to RETS120H-12 drawing for LM120H-12 or RETS120-12K drawing for LM120K-12 military specifications. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 3 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com LM120K-12 ELECTRICAL CHARACTERISTICS Metal Can Package Order Numbers LM120K-12 (TO-3) Design Output Current (ID) 1A Device Dissipation (PD) Parameter Output Voltage Units 20W Conditions (1) TJ = 25C, VIN = 17V, Min Typ Max -12.3 -12 -11.7 V 4 10 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -32 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 17V, (2) -14 56 80 V dB 30 80 mV -11.5 V 2 4 mA 5 mA ILOAD ID Output Voltage, (3) 14.5V VIN VMAX, -12.5 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.1 0.4 mA 5 mA ILOAD ID 0.1 0.4 mA TA = 25C, CL = 1 F, IL = 5 mA, 400 Output Noise Voltage V VIN = 17V, 10 Hz f 100 kHz Long Term Stability 12 120 mV Junction to Case 3 C/W Junction to Ambient 35 C/W Thermal Resistance (1) (2) (3) This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. LM120H-12 ELECTRICAL CHARACTERISTICS Metal Can Package Order Numbers LM120H-12 (TO) Design Output Current (ID) 0.2A Device Dissipation (PD) Parameter Output Voltage Conditions Units 2W (1) TJ = 25C, VIN = 17V, Min Typ Max -12.3 -12 -11.7 V 4 10 mV -14 V 25 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -32 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 17V, (1) 4 56 80 10 dB This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 LM120H-12 ELECTRICAL CHARACTERISTICS (continued) Metal Can Package Order Numbers LM120H-12 (TO) Design Output Current (ID) 0.2A Device Dissipation (PD) Parameter (2) Units 2W Conditions (1) Min Typ Max 5 mA ILOAD ID Output Voltage, (1) 14.5V VIN VMAX, -12.5 -11.5 V 2 4 mA 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.05 0.4 mA 5 mA ILOAD ID 0.03 0.4 mA TA = 25C, CL = 1 F, IL = 5 mA, 400 Output Noise Voltage V VIN = 17V, 10 Hz f 100 kHz Long Term Stability 12 120 mV Thermal Resistance Junction to Case (3) C/W Junction to Ambient (3) C/W (2) (3) Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Thermal resistance of typically 85C/W (in 400 linear feet/min air flow), 224C/W (in static air) junction to ambient, of typically 21C/W junction to case. LM320T-12 ELECTRICAL CHARACTERISTICS Power Plastic Package Order Numbers LM320T-12 (TO-220) Design Output Current (ID) 1A Device Dissipation (PD) Parameter Output Voltage Conditions TJ = 25C, VIN = 17V, Units 15W (1) Min Typ Max -12.4 -12 -11.6 V 4 20 mV -14.5 V 80 mV -11.4 V 2 4 mA ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -32 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 17V, (2) 56 80 30 dB 5 mA ILOAD ID Output Voltage, (1) 14.5V VIN VMAX, -12.6 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.1 0.4 mA 5 mA ILOAD ID 0.1 0.4 mA (1) (2) This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 5 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com LM320T-12 ELECTRICAL CHARACTERISTICS (continued) Power Plastic Package Order Numbers LM320T-12 (TO-220) Design Output Current (ID) 1A Device Dissipation (PD) Parameter Units 15W Conditions (1) Min Typ TA = 25C, CL = 1 F, IL = 5 mA, Max 400 V 24 mV Junction to Case 4 C/W Junction to Ambient 50 C/W Output Noise Voltage VIN = 17V, 10 Hz f 100 kHz Long Term Stability Thermal Resistance ABSOLUTE MAXIMUM RATINGS-15 VOLT REGULATORS (1) (2) Power Dissipation Internally Limited Input Voltage LM120/LM320-N -40V LM320T -35V Input-Output Voltage Differential 30V (3) Junction Temperatures -65C to +150C Storage Temperature Range Lead Temperature (Soldering, 10 sec.) (1) (2) (3) 300C Refer to RETS120-15H drawing for LM120H-15 or RETS120-15K drawing for LM120K-15 military specifications. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. LM120K-15 AND LM320K-15 ELECTRICAL CHARACTERISTICS Metal Can Package Order Numbers LM120K-15 (TO-3) LM320K-15 (TO-3) Design Output Current (ID) Device Dissipation (PD) Parameter Output Voltage Units 1A 20W Conditions TJ = 25C, VIN = 20V, (1) Min Typ Max Min Typ Max -15.3 -15 -14.7 -15.4 -15 -14.6 V 5 10 5 20 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -35 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 20V, (2) (1) 30 -35 56 80 -17 80 30 V dB 80 mV 17.5V VIN VMAX, -15.5 -14.5 -15.6 -14.4 V 4 mA 5 mA ILOAD ID, P PD Quiescent Current 6 -17 80 5 mA ILOAD ID Output Voltage, (1) (2) 56 VMIN VIN VMAX 2 4 2 This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 LM120K-15 AND LM320K-15 ELECTRICAL CHARACTERISTICS (continued) Metal Can Package Order Numbers LM120K-15 (TO-3) LM320K-15 (TO-3) Design Output Current (ID) Device Dissipation (PD) Parameter 20W Conditions (1) Min Typ Max Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.1 5 mA ILOAD ID 0.1 TA = 25C, CL = 1 F, IL = 5 mA, 400 Output Noise Voltage Units 1A Min Typ Max 0.4 0.1 0.4 mA 0.4 0.1 0.4 mA V 400 VIN = 20V, 10 Hz f 100 kHz Long Term Stability 15 150 15 150 mV Thermal Resistance Junction to Case 3 3 C/W Junction to Ambient 35 35 C/W LM120H-15 ELECTRICAL CHARACTERISTICS Metal Can Package Order Numbers LM120H-15 (TO) Design Output Current (ID) 0.2A Device Dissipation (PD) Parameter Output Voltage Conditions Units 2W (1) TJ = 25C, VIN = 20V, Min Typ Max -15.3 -15 -14.7 V 5 10 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -35 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 20V, (2) 56 -17 V 80 10 dB 25 mV -14.5 V 2 4 mA 5 mA ILOAD ID Output Voltage, (1) 17.5V VIN VMAX, -15.5 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.05 0.4 mA 5 mA ILOAD ID 0.03 0.4 mA TA = 25C, CL = 1 F, IL = 5 mA, 400 Output Noise Voltage V VIN = 20V, 10 Hz f 100 kHz Long Term Stability 15 150 mV Thermal Resistance (1) (2) (3) Junction to Case (3) C/W Junction to Ambient (3) C/W This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Thermal resistance of typically 85C/W (in 400 linear feet/min air flow), 224C/W (in static air) junction to ambient, of typically 21C/W junction to case. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 7 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com LM320T-15 ELECTRICAL CHARACTERISTICS Power Plastic Package Order Numbers LM320T-15 (TO-220) Design Output Current (ID) 1A Device Dissipation (PD) Parameter Output Voltage Conditions Units 15W (1) TJ = 25C, VIN = 20V, Min Typ Max -15.5 -15 -14.5 V 5 20 mV ILOAD = 5 mA Line Regulation TJ = 25C, ILOAD = 5 mA, VMIN VIN VMAX -35 Input Voltage Ripple Rejection f = 120 Hz Load Regulation, TJ = 25C, VIN = 20V, (2) 56 -17.5 80 30 V dB 80 mV -14.3 V 2 4 mA 5 mA ILOAD ID Output Voltage, (1) 17.5V VIN VMAX, -15.7 5 mA ILOAD ID, P PD Quiescent Current VMIN VIN VMAX Quiescent Current TJ = 25C Change VMIN VIN VMAX 0.1 0.4 mA 5 mA ILOAD ID 0.1 0.4 mA TA = 25C, CL = 1 F, IL = 5 mA, 400 V 30 mV Junction to Case 4 C/W Junction to Ambient 50 C/W Output Noise Voltage VIN = 20V, 10 Hz f 100 kHz Long Term Stability Thermal Resistance (1) (2) 8 This specification applies over -55C TJ +150C for the LM120 and 0C TJ +125C for the LM320-N. Regulation is measured at constant junction temperature. Changes in output voltage due to heating effects must be taken into account separately. To ensure constant junction temperature, low duty cycle, pulse testing is used. The LM120/LM320-N series does have low thermal feedback, improving line and load regulation. On all other tests, even though power dissipation is internally limited, electrical specifications apply only up to PD. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Output Voltage vs Temperature Ripple Rejection (All Types) Figure 3. Figure 4. Output Impedance TO-3 and TO-220 Packages Output Impedance TO-5 and TO-202 Packages Figure 5. Figure 6. Minimum Input-Output Differential TO-3 and TO-220 Packages Minimum Input-Output Differential TO-5 and TO-202 Packages Figure 7. Figure 8. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 9 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Quiescent Current vs Input Voltage Quiescent Current vs Load Current Figure 9. Figure 10. Maximum Average Power Dissipation (TO-3) Maximum Average Power Dissipation (TO-5) *These curves for LM120. Derate 25C further for LM320-N. Figure 11. 10 Figure 12. Maximum Average Power Dissipation (TO-202) Maximum Average Power Dissipation (TO-220) Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Short Circuit Current Figure 15. Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 11 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com TYPICAL APPLICATIONS Lead and line regulation -- 0.01% temperature stability -- 0.2% Determines Zener current. Solid tantalum. An LM120-12 or LM120-15 may be used to permit higher input voltages, but the regulated output voltage must be at least -15V when using the LM120-12 and -18V for the LM120-15. **Select resistors to set output voltage. 2 ppm/C tracking suggested. Figure 16. High Stability 1 Amp Regulator *Resistor tolerance of R1 and R2 determine matching of (+) and (-) inputs. **Necessary only if raw supply capacitors are more than 3 from regulators An LM3086N array may substitute for Q1, D1 and D2 for better stability and tracking. In the array diode transistors Q5 and Q4 (in parallel) make up D2; similarly, Q1 and Q2 become D1 and Q3 replaces the 2N2222. Figure 17. Wide Range Tracking Regulator 12 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 Figure 18. Current Source SELECT R2 AS FOLLOWS: LM120-5 300 LM120-12 750 LM120-15 1k *C3 optional. Improves transient response and ripple rejection. Figure 19. Variable Output Current Source Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 13 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com See Performance (Typical) *Resistor tolerance of R4 and R5 determine matching of (+) and (-) outputs. **Necessary only if raw supply filter capacitors are more than 2 inches from regulators. Figure 20. 15V, 1 Amp Tracking Regulators Performance (Typical) Load Regulation at IL = 1A Output Ripple, CIN = 3000 F, IL = 1A Temperature Stability Output Noise 10 Hz f 10 kHz 10 mV 1 mV 100 Vrms 100 Vrms +50 mV +50 mV 150 Vrms 150 Vrms Light Controllers Using Silicon Photo Cells *Lamp brightness increases until iI = 5V/R1 (iI can be set as low as 1 A). Necessary only if raw supply filter capacitor is more than 2 inches from LM320MP. 14 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 *Lamp brightness increases until iI =iQ (1 mA) + 5V/R1. Necessary only if raw supply filter capacitor is more than 2 inches from LM320-N. Connection Diagram Figure 21. Steel Metal Can Package TO-3 (NDS) (Bottom View) Figure 22. Metal Can Package TO (NDT) (Bottom View) Figure 23. Power Package TO-220 (NDE) (Front View) Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 15 LM120, LM320-N SNVS756C - APRIL 1998 - REVISED APRIL 2013 www.ti.com Schematic Diagrams Figure 24. -5V Figure 25. -12V and -15V 16 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N LM120, LM320-N www.ti.com SNVS756C - APRIL 1998 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision B (April 2013) to Revision C * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Submit Documentation Feedback Copyright (c) 1998-2013, Texas Instruments Incorporated Product Folder Links: LM120 LM320-N 17 PACKAGE OPTION ADDENDUM www.ti.com 30-Apr-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) (6) LM120H-12 ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-12P+, LM1 20H-12P+) LM120H-12/NOPB ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-12P+, LM1 20H-12P+) LM120H-15 ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-15P+, LM1 20H-15P+) LM120H-15/NOPB ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-15P+, LM1 20H-15P+) LM120H-5.0 ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-5.0P+, LM 120H-5.0P+) LM120H-5.0/NOPB ACTIVE TO NDT 3 500 RoHS & Green AU Level-1-NA-UNLIM -55 to 150 ( LM120H-5.0P+, LM 120H-5.0P+) LM320T-15 NRND TO-220 NDE 3 45 Non-RoHS & Green Call TI Call TI 0 to 125 LM320T -15 P+ LM320T-15/NOPB ACTIVE TO-220 NDE 3 45 RoHS & Green SN Level-1-NA-UNLIM 0 to 125 LM320T -15 P+ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 30-Apr-2021 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NDT0003A H03A (Rev D) www.ti.com MECHANICAL DATA NDE0003B www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2021, Texas Instruments Incorporated