HIF3BA-16D-2.54R(05) - Hirose Electric

B15

Ribbon Cable connector Compliant with MIL Standard

HIF3B Series

■Features

1. Product Compliant with MIL Standard

HIF3B series has been developed as a product compliant with MIL

standard, and used for wide applications.

2. UL Approval Product

HIF3B series connectors are UL approved.

3. Mechanism to Prevent Mis-insertion

This connector is equipped with the mechanism to prevent Mis-

insertion as follows.

1The system provides the convex area to insert the guide-key on the

pin header side, and to guide it in combination with the socket

convex area (MIL standard).

2

The system embeds and guides the polarizing key in the socket holes.

4. Applicable Cable AWG#28

The applicable cable is UL2651 AWG#28 flat cable (7 cores./

0.127mm, jacket dia. 0.9±0.1mm).

■Product Specifications

Note 1: Includes temperature rise caused by current flow.

Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and

Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.

Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a

specific part number shown.

Note 4: Please note that there is a risk of deforming the lock when an excessive load is applied to the inside.

Rating Current rating : 1A

Operating Temperature Range

:

–55 to +85ç(Note 1)

Storage Temperature Range : –10 to +60ç(Note 2)

Voltage rating : 200V AC Operating Moisture Range : 40 to 80%Storage Humidity Range : 40 to 70% (Note 2)

Item Specification Condition

1. Insulation Resistance 1000M ohms min. 500V DC

2. Withstanding voltage No flashover or insulation breakdown. 650V AC/1 minute

3. Contact Resistance 15m ohms max. 0.1A

4.

Vibration

No electrical discontinuity of 1μs or more

Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.

5.

Humidity (Steady state)

Insulation resistance: 1000M ohms min.

96 hours at temperature of 40ç and humidity of 90% to 95%

6. Temperature Cycle No damage, cracks, or parts looseness.

(-55ç: 30 minutes ➝ 15 to 35ç: 5 minutes max.

125ç: 30 minutes ➝15 to 35ç: 5 minutes max.) 5 cycles

7.

Durability (Mating/un-mating)

Contact resistance: 15m ohms max. 500 cycles

8.

Resistance to Soldering heat

No deformation of components affecting performance.

Solder bath: 260ç for 10 seconds

Manual soldering: 360ç for 5 seconds

■Material

Part Material Finish Remarks

Insulator PBT Black UL94V-0

Socket Contact Beryllium copper Connection area Gold plated –––––––

Pin header contact Brass Selective Gold plated –––––––

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B16

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Ordering Information

HIF 3B - *D - 2.54 R

qw rety

qSeries Name : HIF

wSeries No. : 3B, 3BA, 3BB (50, 60, 64 contacts only)

e

Number of contacts

: 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64

r

Contact alignment

: D : Double

tContact pitch : 2.54mm

yConnection type

R : ID type

●Socket

HIF 3B - *P A - 2.54 DS

qw ret yu

qSeries Name : HIF

wSeries No. :

3B :

(14 contacts not included)

3BC: (10 contacts only)

3BA, 3BB: (50, 60, 64 contacts only) 3BD: (10 contacts only)

e

Number of contacts

: 6,10,14,16, 20, 26, 30, 34, 40, 50, 60, 64

rP : Pin header

tA : Selective gold plated

yContact pitch : 2.54mm

uContact style

DS : Right angle type

DSA : Straight type

●Pin Header

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B17

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Socket (With guide to prevent mis-insertion)

Unit:mm

★

Note1, Note2: The number of polarizing keys and polarizing keyways changes according to products. Refer to the list as shown below.

Note3: The 50, 60 and 64 contact connector contain two types of polarizing guides. Use the products, referring to Notes 1 and 2.

Note4: The 6 contact has no polarizing mark.

The products marked with

★

comply with MIL standard.

Body Protector Clamp

CL No.Part Number

610-0032-3

610-0021-7

610-0022-0

610-0023-2

610-0024-5

610-0025-8

610-0026-0

610-0027-3

610-0028-6

610-0029-9

610-0041-4

610-0030-8

610-0042-7

610-0031-0

610-0043-0

HIF3BA- 6D-2.54R

HIF3BA-10D-2.54R

HIF3BA-14D-2.54R

HIF3BA-16D-2.54R

HIF3BA-20D-2.54R

HIF3BA-26D-2.54R

HIF3BA-30D-2.54R

HIF3BA-34D-2.54R

HIF3BA-40D-2.54R

HIF3BA-50D-2.54R

HIF3BB-50D-2.54R

HIF3BA-60D-2.54R

HIF3BB-60D-2.54R

HIF3BA-64D-2.54R

HIF3BB-64D-2.54R

Number of Contacts

6

10

14

16

20

26

30

34

40

50

60

64

A

12.19

17.27

22.35

24.89

29.97

37.59

42.67

47.75

55.37

68.07

80.77

85.85

B

5.08

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

C

6.35

11.43

16.51

19.05

24.13

31.75

36.83

41.91

49.53

62.23

74.93

80.01

D

7.72

12.8

17.88

20.42

25.5

33.12

38.2

43.28

50.9

63.6

76.3

81.38

Polarizing Guide

(Note 1)

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

Polarizing Keyway

(Note 2)

RoHS

None

One on left side

One on right and

left sides, resp.

YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B18

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Socket

Note1: The number of polarizing keys and polarizing keyways changes according to products. For details, refer to the list as shown below.

Note2: The 6 contact has no polarizing mark.

Body Protector Clamp

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0012-6

610-0001-0

610-0002-2

610-0003-5

610-0004-8

610-0005-0

610-0006-3

610-0007-6

610-0008-9

610-0009-1

610-0010-0

610-0011-3

HIF3B- 6D-2.54R

HIF3B-10D-2.54R

HIF3B-14D-2.54R

HIF3B-16D-2.54R

HIF3B-20D-2.54R

HIF3B-26D-2.54R

HIF3B-30D-2.54R

HIF3B-34D-2.54R

HIF3B-40D-2.54R

HIF3B-50D-2.54R

HIF3B-60D-2.54R

HIF3B-64D-2.54R

Number of Contacts

6

10

14

16

20

26

30

34

40

50

60

64

A

12.19

17.27

22.35

24.89

29.97

37.59

42.67

47.75

55.37

68.07

80.77

85.85

B

5.08

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

C

6.35

11.43

16.51

19.05

24.13

31.75

36.83

41.91

49.53

62.23

74.93

80.01

D

7.72

12.80

17.88

20.42

25.50

33.12

38.2

43.28

50.90

63.6

76.3

81.38

Polarizing Guide

(Note 1)

RoHS

None

One on left side

One on right and

left sides, resp.

YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B19

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Four Wall Angle Through hole

BPCB mounting pattern

Note 1, Note 2: The number of polarizing slot and key installed positions

changes according to products. Refer to the list as shown below.

Note 3: The spacer moves to the right according to the number of

contacts.

Note 4: The 10, 50, 60 and 64 contact connectors contain two types of

polarizing slots.

Use products, referring to (Note 1) (Note 2).

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0091-2(71)

610-0171-0(71)

610-0092-5(71)

610-0093-8(71)

610-0094-0(71)

610-0095-3(71)

610-0096-6(71)

610-0097-9(71)

610-0098-1(71)

610-0099-4(71)

610-0131-5(71)

610-0100-1(71)

610-0132-8(71)

610-0101-4(71)

610-0133-0(71)

HIF3BA-10PA-2.54DS(71)

HIF3BD-10PA-2.54DS(71)

HIF3BA-14PA-2.54DS(71)

HIF3BA-16PA-2.54DS(71)

HIF3BA-20PA-2.54DS(71)

HIF3BA-26PA-2.54DS(71)

HIF3BA-30PA-2.54DS(71)

HIF3BA-34PA-2.54DS(71)

HIF3BA-40PA-2.54DS(71)

HIF3BA-50PA-2.54DS(71)

HIF3BB-50PA-2.54DS(71)

HIF3BA-60PA-2.54DS(71)

HIF3BB-60PA-2.54DS(71)

HIF3BA-64PA-2.54DS(71)

HIF3BB-64PA-2.54DS(71)

Number of Contacts

10

14

16

20

26

30

34

40

50

60

64

A

32.0

37.1

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

22.6

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

26.9

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

33.0

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

None

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

Polarizing Key Install

(Note 2) RoHS

One on right side

None

One on right side

One on right and

left sides, resp.

YES

D

28.14

MAX51.1

28.14

MAX51.1

33.24

MAX56.2

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

78.94

MAX101.9

91.64

MAX114.6

91.64

MAX114.6

96.74

MAX119.7

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B20

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Four-Wall Straight Through hole

BPCB mounting pattern

Note 1, Note 2: The number of polarizing slot and key installed positions

changes according to products. Refer to the list as shown below.

Note 3: The spacer moves to the right according to the number of

contacts.

Note 4: The 10, 50, 60 and 64 contact connectors contain two types of

polarizing slots.

Use products, confirming (Note 1) (Note 2).

Note 5: The 6 contact has no polarity mark.

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

562-0503-9-71

610-0111-8-71

610-0181-3-71

610-0112-0-71

610-0113-3-71

610-0114-6-71

610-0115-9-71

610-0116-1-71

610-0117-4-71

610-0118-7-71

610-0119-0-71

610-0141-9-71

610-0120-9-71

610-0142-1-71

610-0121-1-71

610-0143-4-71

HIF3-6PA-2.54DSA(71)

HIF3BA-10PA-2.54DSA(71)

HIF3BD-10PA-2.54DSA(71)

HIF3BA-14PA-2.54DSA(71)

HIF3BA-16PA-2.54DSA(71)

HIF3BA-20PA-2.54DSA(71)

HIF3BA-26PA-2.54DSA(71)

HIF3BA-30PA-2.54DSA(71)

HIF3BA-34PA-2.54DSA(71)

HIF3BA-40PA-2.54DSA(71)

HIF3BA-50PA-2.54DSA(71)

HIF3BB-50PA-2.54DSA(71)

HIF3BA-60PA-2.54DSA(71)

HIF3BB-60PA-2.54DSA(71)

HIF3BA-64PA-2.54DSA(71)

HIF3BB-64PA-2.54DSA(71)

Number of Contacts

6

10

14

16

20

26

30

34

40

50

60

64

A

26.92

32.0

37.1

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

12.42

17.5

22.6

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

05.08

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

16.7

21.8

26.9

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

22.82

27.9

33.0

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

One at center

None

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

Polarizing Key Install

(Note 2) RoHS

None

One on right side

None

One on right side

One on right and

left sides, resp.

YES

D

23.06

MAX46.02

28.14

MAX51.1

28.14

MAX51.1

33.24

MAX56.2

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

78.94

MAX101.9

91.64

MAX114.6

91.64

MAX114.6

96.74

MAX119.7

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B21

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Three Wall Angle Type

BPCB mounting pattern

Note 1, Note 2: The number of polarizing slot and key installed positions

changes according to products. Refer to the list as shown below.

Note 3: The spacer moves according to the number of contacts.

Note 4: The 10 contact connector consists of two types.

Use products, confirming (Note 1) (Note 2).

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0051-8-71

610-0151-2-71

610-0052-0-71

610-0053-3-71

610-0054-6-71

610-0055-9-71

610-0056-1-71

610-0057-4-71

610-0058-7-71

610-0059-0-71

610-0060-9-71

HIF3BD-10PA-2.54DS(71)

HIF3BC-10PA-2.54DS(71)

HIF3BD-16PA-2.54DS(71)

HIF3BD-20PA-2.54DS(71)

HIF3BD-26PA-2.54DS(71)

HIF3BD-30PA-2.54DS(71)

HIF3BD-34PA-2.54DS(71)

HIF3BD-40PA-2.54DS(71)

HIF3BD-50PA-2.54DS(71)

HIF3BD-60PA-2.54DS(71)

HIF3BD-64PA-2.54DS(71)

Number of Contacts

10

16

20

26

30

34

40

50

60

64

A

32.0

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

None

One at center

One on right and left sides, resp.

Polarizing Key Install

(Note 2) RoHS

One on right side

None

One on right and

left sides, resp. YES

D

28.14

MAX51.1

28.14

MAX51.1

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

91.64

MAX114.6

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B22

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Three Wall Straight Through hole

BPCB mounting pattern

Note1,Note2: The number of polarizing slot and key installed positions

changes according to products. Refer to the list as shown

below.

Note3: The spacer moves to the right according to the number of

contacts.

Note4: The 10 contact connector consists of two types.

Use products, referring to (Note 1) and (Note 2).

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0071-5-71

610-0161-6-71

610-0072-8-71

610-0073-0-71

610-0074-3-71

610-0075-6-71

610-0076-9-71

610-0077-1-71

610-0078-4-71

610-0079-7-71

610-0080-6-71

HIF3BD-10PA-2.54DSA(71)

HIF3BC-10PA-2.54DSA(71)

HIF3BD-16PA-2.54DSA(71)

HIF3BD-20PA-2.54DSA(71)

HIF3BD-26PA-2.54DSA(71)

HIF3BD-30PA-2.54DSA(71)

HIF3BD-34PA-2.54DSA(71)

HIF3BD-40PA-2.54DSA(71)

HIF3BD-50PA-2.54DSA(71)

HIF3BD-60PA-2.54DSA(71)

HIF3BD-64PA-2.54DSA(71)

Number of Contacts

10

16

20

26

30

34

40

50

60

64

A

32.0

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

None

One at center

One on right and left sides, resp.

Polarizing Key Install

(Note 2) RoHS

One on right side

None

One on right and

left sides, resp.

YES

D

28.14

MAX51.1

28.14

MAX51.1

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

91.64

MAX114.6

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B23

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Four Wall Wrapping Type

BPCB mounting pattern

Note 1, Note 2. The number of polarizing slot and key installed positions

changes according to products. Refer to the list as shown below.

Note 3. The spacer moves to the right according to the number of

contacts.

Note 4. The 10, 50, 60 and 64 contact connectors consists of two types.

Use products, confirming (Note 1) (Note 2).

Note 5. The mark *indicates the number of contacts.

Note 6. The nut built-in specification product is also provided.

The product can be fixed by M2 screws from the rear side.

Use the screw of (board thickness) +4 mm under the neck.

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0503-8

610-0492-3

610-0493-6

610-0494-9

610-0495-1

610-0496-4

610-0497-7

610-0498-0

610-0499-2

610-0504-0

610-0500-0

610-0505-3

610-0501-2

610-0506-6

610-0502-5

HIF3BA-10P-2.54W

HIF3BD-10P-2.54W

HIF3BA-14P-2.54W

HIF3BA-16P-2.54W

HIF3BA-20P-2.54W

HIF3BA-26P-2.54W

HIF3BA-30P-2.54W

HIF3BA-34P-2.54W

HIF3BA-40P-2.54W

HIF3BA-50P-2.54W

HIF3BB-50P-2.54W

HIF3BA-60P-2.54W

HIF3BB-60P-2.54W

HIF3BA-64P-2.54W

HIF3BB-64P-2.54W

Number of Contacts

10

14

16

20

26

30

34

40

50

60

64

A

32.0

37.1

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

22.6

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

26.9

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

33.0

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

None

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

Polarizing Key Install

(Note 2) RoHS

One on right side

None

One on right side

One on right and

left sides, resp.

YES

D

28.14

MAX51.1

28.14

MAX51.1

33.24

MAX56.2

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

78.94

MAX101.9

91.64

MAX114.6

91.64

MAX114.6

96.74

MAX119.7

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B24

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Four Wall Straight Through hole

[Flux Blister Prevention Type]

BPCB mounting pattern

Note1: The number of polarizing slot and key installed positions changes

according to products. Refer to the list as shown below.

■n=number of contacts

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-0701-1-71

610-0722-1-71

610-0703-7-71

610-0704-0-71

610-0705-2-71

610-0706-5-71

610-0707-8-71

610-0708-0-71

610-0709-3-71

610-0721-9-71

610-0723-4-71

610-0724-7-71

HIF3CA-10PA-2.54DSA(71)

HIF3CD-10PA-2.54DSA(71)

HIF3CA-16PA-2.54DSA(71)

HIF3CA-20PA-2.54DSA(71)

HIF3CA-26PA-2.54DSA(71)

HIF3CA-30PA-2.54DSA(71)

HIF3CA-34PA-2.54DSA(71)

HIF3CA-40PA-2.54DSA(71)

HIF3CA-50PA-2.54DSA(71)

HIF3CB-50PA-2.54DSA(71)

HIF3CB-60PA-2.54DSA(71)

HIF3CB-64PA-2.54DSA(71)

Number of Contacts

10

16

20

26

30

34

40

50

60

64

A

32.0

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

None

One at center

One on right and left sides, resp.

One at center

Polarizing Key Install RoHS

One on right side

None

One on right and

left sides, resp.

YES

D

28.14

MAX51.1

28.14

MAX51.1

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

78.94

MAX101.9

91.64

MAX114.6

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B25

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Two Stage Staking Right Angle Through hole

Note 1, Note 2: The number of polarizing slot and key installed positions changes according to products. Refer

to the list as shown below.

Note 3: The spacer moves to the right according to the number of contacts.

Note 4: The 10, 50, 60 and 64 contact connectors consists of two types.

Use products, confirming (Note 1) (Note 2).

Note 5: The mark *ndicates the number of contacts.

Note 6: The locator is located optionally.

Unit:mm

★

The products marked with

★

comply with MIL standard.

CL No.Part Number

610-1502-0-71

610-1503-3-71

610-1505-9-71

610-1506-1-71

610-1507-4-71

610-1508-7-71

610-1509-0-71

610-1510-9-71

610-1511-1-71

610-1512-4-71

610-1513-7-71

610-1514-0-71

610-1515-2-71

610-1516-5-71

HIF3BA-10PA-2.54WB(71)

HIF3BD-10PA-2.54WB(71)

HIF3BA-16PA-2.54WB(71)

HIF3BA-20PA-2.54WB(71)

HIF3BA-26PA-2.54WB(71)

HIF3BA-30PA-2.54WB(71)

HIF3BA-34PA-2.54WB(71)

HIF3BA-40PA-2.54WB(71)

HIF3BA-50PA-2.54WB(71)

HIF3BB-50PA-2.54WB(71)

HIF3BA-60PA-2.54WB(71)

HIF3BB-60PA-2.54WB(71)

HIF3BA-64PA-2.54WB(71)

HIF3BB-64PA-2.54WB(71)

Number of Contacts

10

16

20

26

30

34

40

50

60

64

A

32.0

39.6

44.7

52.3

57.4

62.5

70.1

82.8

95.5

100.6

B

17.5

25.1

30.2

37.8

42.9

48.0

55.6

68.3

81.0

86.1

C

10.16

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

E

21.8

29.5

34.5

42.2

47.2

52.3

59.9

72.6

85.3

90.4

27.9

35.5

40.6

48.3

53.3

58.4

66.0

78.7

91.4

96.5

FPolarizing Slot

(Note 1)

None

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

One on right and left sides, resp.

One at center

Polarizing Key Install

(Note 2) RoHS

One on right side

None

One on right and

left sides, resp.

YES

D

28.14

MAX51.1

28.14

MAX51.1

35.74

MAX58.7

40.84

MAX63.8

48.44

MAX71.4

53.54

MAX76.5

58.64

MAX81.6

66.24

MAX89.2

78.94

MAX101.9

78.94

MAX101.9

91.64

MAX114.6

91.64

MAX114.6

96.74

MAX119.7

96.74

MAX119.7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B26

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

BCombination Pattern

BPCB mounting pattern

■Mounting Hole Spacer

Note : Fix the HIF3-mounting hole spacer by screws between upper stage and lower stage connectors.

Part Number CL No. Finish RoHS

HIF-3 mounting hole spacer

562-0714-4 PBT Black YES

Note : 2 pieces are contained in a bag.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B27

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

BPolarizing Key

Note1: One unit of this

product is a set of five

pieces in conjunction

with a runner. The unit

for sale is defined one

pack containing 20

pieces.

Note2: This product is

applicable to the

HIF3BA-*D2.54R

product.

Part Number CL No. Material

HIF3-GPIN(A) 562-0126-6 Poly acetal (white) Remarks

RoHS

A set of 5 pieces

YES

HIF3-GPIN(A) HIF3BA-GPIN

Note1: One unit of this

product is a set of five

pieces in conjunction

with a runner. The unit

for sale is defined one

pack containing 20

pieces.

Note2: This product is

applicable to HIF3A-

*D2.54R, HIF3C-

*D2.54C and

HIF3BA-*D2.54C

products.

HIF3B-GK

CL562-0601-8

Part Number CL No. Material

HIF3BA-GPIN 612-0500-2 Poly acetal (white) Remarks

RoHS

A set of 5 pieces

YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B28

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

BHIF3-Multi Clamp BHIF3-*CL Pull Tab

Lock G

●Low Profile Lock Pin Header

BLock

●F Type Lock Pin Header

Lock F

Part Number : HIF3BAG-**PA-2.54DSA(71)

●Low profile type, and used for lock ejection.

Connector height is reduced.

Since no connector clamp is needed on the cable side,

this is used without turning back on the cable side. Take

care about this point.

Part Number : HIF3BAG-**PA-2.54DSA(71)

●Locking range more reduced than conventional lock type.

Even if connectors are aligned laterally, the mounting

space is reduced.

Note : The clamp must be replaced for HIF3A socket type

60 contacts only. Take care about this point.

This clamp is used for intermediate connection in the

bus-line system, etc. Remove compulsory force from the

insulation displacement area of the connector in

intermediate connection.

Note: The pin header corresponds to the HIF3BAE

series (lock E).

This pull tab is used for the HIF3 series equipped with cable clamp

function. Remove all compulsory force, which is loaded on the

insulation displacement area of the connector for extraction.

Note: This HIF3-* Pull Tab can not be used for HIF3BA-*PD.

Note: The pin header corresponds to the HIF3BAE series (lock E).

27.3

21.5

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B29

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

Part Number CL No.

610-1041-0

610-1051-3

610-1042-2

610-1043-5

610-1044-8

610-1045-0

610-1046-3

610-1047-6

610-1048-9

610-1061-7

610-1049-1

610-1062-0

610-1064-5

610-1063-2

Number of Contacts

A B

10

14

16

20

26

30

34

40

50

60

64

17.25

22.35

24.8

29.95

37.55

42.63

47.75

55.35

68.04

80.77

85.85

10.16

15.24

17.78

22.86

30.48

35.56

40.64

48.26

60.96

73.66

78.74

Polarizing Guide RoHS

One at center

One right and left side, resp.

One at center

One right and left side, resp.

One at center

One right and left side, resp.

One at center

YES

HIF3BA-10D-2.54C

HIF3BA-14D-2.54C

HIF3BA-16D-2.54C

HIF3BA-20D-2.54C

HIF3BA-26D-2.54C

HIF3BA-30D-2.54C

HIF3BA-34D-2.54C

HIF3BA-40D-2.54C

HIF3BA-50D-2.54C

HIF3BB-50D-2.54C

HIF3BA-60D-2.54C

HIF3BB-60D-2.54C

HIF3BA-64D-2.54C

HIF3BB-64D-2.54C

Unit: mm

■Socket for Crimping

Note: Some variations may differ from those in above figures.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B30

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

■Cover Case for Crimping socket

Part Number CL No.

562-0201-0-71

562-0202-2-71

562-0203-5-71

562-0204-8-71

562-0205-0-71

562-0206-3-71

562-0207-6-71

Number of Contacts

A B

20

26

30

34

40

50

60

24.5

30.2

32.2

34.2

36.2

39.2

42.2

18.0

20.0

22.0

24.0

26.0

29.0

32.0

C

12.0

14.0

16.0

18.0

20.0

23.0

26.0

D

30.5

32.0

33.0

33.5

35.5

38.0

40.5

ERoHS

29.95

37.55

42.63

47.75

55.35

68.04

80.77

YES

HIF3-20CV(71)

HIF3-26CV(71)

HIF3-30CV(71)

HIF3-34CV(71)

HIF3-40CV(71)

HIF3-50CV(71)

HIF3-60CV(71)

Unit: mm

Note 1: The type F lock pin header cannot be used for a mating member.

Note 2: Note that the product cannot be used with AWG #20.

Applicable jacket diameters are as described below.

20 contacts: 1.7 mm diameter MAX

26 to 40 contacts: 1.6 mm diameter MAX

50 to 60 contacts: 1.4 mm diameter MAX

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B31

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

HIF3-2226SC

HIF3-2226SCA

Applicable cable

Manual crimping tool

562-0079-8

562-0244-2

gold plated contact in bag

Selective gold plated contact in bag

RoHS

YES

AWG#22 to #26 UL 1007 Stranded wire

HIF3-T2226HC

HIF3-2428SC

HIF3-2428SCA

Applicable cable

Manual crimping tool

562-0124-0

562-0246-8

gold plated contact in bag

Selective gold plated contact in bag

AWG#24 to #28 UL 1007 Stranded wire

HIF3-TA2428HC

HIF3-2022SC

Applicable cable

Manual crimping tool

562-0492-4

gold plated contact in bag

AWG#20 to #22 UL 1007 Stranded wire

HIF3-TA2022HC

■Contact for Crimping Socket

HIF3-2226SCF

HIF3-2226SCFA

Applicable cable

**

562-0080-7

562-0245-5

gold plated contact in reel

Selective gold plated contact in reel

AWG#22 to #26 UL 1007 Stranded wire

Note:* products have both side careers.

HIF3-2226SCC

HIF3-2630SCC

Part Number

613-0004-7

613-0003-4

CL No.

AWG#22 to #26 UL 1007 Stranded wire

AWG#26 to #30 UL 1007 Stranded wire

Applicable Cable

HIF3-TB2226HC

HIF3-TB2630HC

Manual Crimp Tool

F

2.6

2.1

RoHS

YES

E

2.3

2.0

D

1.8

1.35

C

1.8

1.4

B

0.8

A

11.5

Part Number

HIF3-2226SCFC

HIF3-2630SCFC

HIF3A-3236SCFC

CL No.

613-0002-1

613-0001-9

613-0005-0

Applicable Cable

AWG#22 to #26 UL 1007 Stranded wire

AWG#26 to #30 UL 1007 Stranded wire

AWG#32 to #36 UL 1007 Stranded wire

F

2.6

2.1

1.5

RoHS

YES

E

2.3

2.0

1.4

D

1.8

1.35

1.1

C

1.8

1.4

1.1

B

0.8

1.7

A

11.5

12.4

HIF3-2428SCF

HIF3-2428SCFA

Applicable cable

562-0125-3

562-0247-0

gold plated contact in reel

Selective gold plated contact in reel

AWG#24 to #28 UL 1007 Stranded wire

HIF3-2022SCF

Applicable cable

562-0493-7

gold plated contact in reel

AWG#20 to #22 UL 1007 Stranded wire

Type VA (Selective gold plated in reel)

Type VA (Selective gold plated contact in bag)

RoHS

YES

RoHS

YES

RoHS

YES

RoHS

YES

RoHS

YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B32

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

BTools

●Crimping Tool

Manual Crimping Tool HIF3-T2226HC

●Automatic Crimping Tool (Type: CM-105)

●Contact Extraction Tools How to use the extraction tool

(1) How to extract contacts

As shown in Figure 1, where the

extraction tool is inserted in the lance

fixed slot on the insulated case, slightly

pull the cable, and the contact can be

removed.

(2) How to adjust the lance (raise)

In order to re-insert the contact

removed from the insulated case,

raise the contact lance area using the

tool A, and re-insert the contact, as

shown in Figure 2.

Figure 1

Part Number

HIF1-PO CL No.

550-0049-7

Part Number

HIF3-T2226HC CL No.

550-0063-8

Part Number

CM-105 CL No.

901-0005-4

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B33

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

Type

Manual

Automatic

Item

Manual crimping tool

Automatic crimping tool unit

Applicator

Part Number

HIF3-T2226HC

HIF3-TA2428HC

HIF3-TA2022HC

HIF3-TB2226HC

HIF3-TB2630HC

CM-105

AP105-HIF3-22-28SCF

AP105-HIF3-22-28SCFA

AP105-HIF3-2022S

AP105-HIF3-2226SCFC

AP105-HIF3-2630SCFC

AP105-HIF3-3236SCFC

HIF1-PO

CL No.

550-0063-8

550-0100-2

550-0124-0

550-0154-1

550-0155-4

901-0005-4

901-4031-6

901-4030-3

901-4027-9

901-4005-6

901-4006-9

901-4007-1

550-0049-7

Applicable Contact

HIF3-2226SC

HIF3-2226SCA

HIF3-2428SC

HIF3-2428SCA

HIF3-2022SC

HIF3-2226SCC

HIF3-2630SCC

–––––––

HIF3-2226SCF

HIF3-2428SCF

HIF3-2226SCFA

HIF3-2428SCFA

HIF3-2022SCF

HIF3-2226SCFC

HIF3-2630SCFC

HIF3-3236SCFC

–––––––

Applicable Cable

AWG#22 to #26

AWG#24 to #28

AWG#20 to #22

AWG#22 to #26

AWG#26 to #30

–––––––

AWG#22 to #26

AWG#24 to #28

AWG#22 to #26

AWG#24 to #28

AWG#20 to #22

AWG#22 to #26

AWG#26 to #30

AWG#32 to #36

–––––––

Extraction tool

(Note1)

Note1: AP106-HIF3-22-28SCF and AP105-HIF3-22-28CFA can be modified by changing a few parts.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B34

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

BSocket Side (Crimping) Assembling Procedures

(1) As shown in Figure 1, peel the applicable cable (AWG#20 to #26) jacket, and connect it using crimping jig HIF3-TA2022HC,

HIF3-TA2226HC, or HIF3-TA2426HC. In this case, insert the cable so as to hit the contact cable stripper position as shown

Figure 2.

(2) After connection as shown Figure 2, check the contact direction, and insert the contact as shown Figures 3 and 4. Slightly pull

the cable, and check whether the contact lance position is firmly fixed to the insulation case, as shown in the area (A).

Note1 : For handling procedures for special crimping tools, refer to the "Handling Instruction Manual".

Note2 : Wire strip length: Refer to crimp condition sheet.

Figure 1 Figure 2

Figure 3 Figure 4

Wire strip length

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B35

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

HIF3B Connection Circuit Diagram

Type AB

Type AD

Type CD

Type ABType ADType CD

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B36

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

Type AC

Type CC

Type AA

Type AC

Type CC

Type AA

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B37

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

HIF2E R(S) A to HIF3B Connection Circuit Diagram

Type AA

Type AC

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B38

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

Type BA

Type BC

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B39

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

HIF2E R(S)B to HIF3 Connection Circuit Diagram

Type AA

Type AC

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

B40

HIF3B Series●Ribbon Cable connector Compliant with MIL Standard

Type BA

Type BC

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.