SRM-Series ALUMINUM ELECTROLYTIC CAPACITORS MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS 5mm height, 105C KRE @Coating case covered products are also available @5mm height, 1000-hours-life at 105C @Solvent-proof type (see PRECAUTIONS AND GUIDELINES) 105C SRE ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Leakage Current Dissipation Factor (tane) Low Temperature Characteristics (Max. Impedance Ratio) Endurance Shelf Life -55 to +105C 6.3 to 50Vdc P20% (M) (at 20C, 120Hz) I=0.01CV or 3MA, whichever is greater. Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V) (at 20C after 2 minutes) Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V tanE (Max.) 0.27 0.23 0.19 0.15 0.13 0.11 Add 0.02 for F3 products. (at 20C, 120Hz) Rated voltage (Vdc) 6.3V 10V 16V 25V 35V 50V Z(-25C)/Z(+20C) 2 2 2 2 3 3 Z(-40C)/Z(+20C) (at 120Hz) 3 3 3 5 7 9 The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1000 hours at 105C. FD F3 & F3.5 F4 to F6.3 Capacitance change [P25% of the initial value [P20% of the initial value D.F. (tanE) [200% of the initial specified value [200% of the initial specified value Leakage current [The initial specified value [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours at 105C without voltage applied. FD F3 & F3.5 F4 to F6.3 Capacitance change [P25% of the initial value [P20% of the initial value D.F. (tanE) [200% of the initial specified value [200% of the initial specified value Leakage current [The initial specified value [The initial specified value FP0.5 fD fd F fD' L' FD' Fd Sleeve FP0.3 ?DIMENSIONS (Radial Lead Type=VB) [mm] L' 15min. 4min. (F3 & F3.5) (F4 to F6.3) Gas escape end seal 3 0.4 1.0 6.3 5 4 3.5 0.4 0.45 0.45 0.45 1.0 1.5 2.0 2.5 FD+0.5max. L+1.0max. ?PART NUMBERING SYSTEM KRE 16 VB 47 M Capacitance 0.1MF 0.47MF 1.0MF 4.7MF 10MF 100MF Cap tolerance (P20%) Nominal cap code Radial lead type Rated voltage in volts Series name Code R1 R47 1 4R7 10 100 ?STANDARD RATINGS Vdc mF 0.1 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 6.3 16 10 25 35 50 Case size FDBL (mm) Rated ripple current (mArms) at 105C, 120Hz 3B5 3.5B5 4B5 12 16 21 5B5 36 6.3B5 56 3B5 11 4B5 20 5B5 34 6.3B5 3B5 3.5B5 3.5B5 5B5 5B5 9.4 13 16 25 30 6.3B5 48 3B5 3.5B5 4B5 8.8 12 16 6.3B5 45 3B5 3.5B5 4B5 5B5 5B5 6.3B5 6.3B5 7.7 11 15 20 25 33 40 3B5 3B5 3B5 3B5 3B5 3B5 3B5 3B5 3.5B5 4B5 5B5 6.3B5 6.3B5 1.3 2.0 2.6 3.2 3.8 4.6 5.6 6.9 10 14 19 24 29 52 Note1 : Use next higher voltage part. Note2 : The parts of F3.5B5 will be unified to F4B5. (1/1) CAT. No. E1001D