LM3450 LM3450 LM3450A LED Drivers with Active Power Factor Correction and Phase Dimming Decoder Literature Number: SNVS681C June 20, 2011 LED Drivers with Active Power Factor Correction and Phase Dimming Decoder General Description Features The LM3450/50A is a power factor controller (PFC) with separate phase dimming decoder. The PFC regulates the output voltage while maintaining excellent power factor. The phase dimming decoder interprets the phase angle and remaps it to a 500Hz PWM output. This device is ideal for implementing a dimmable off-line LED driver for 10-100W loads. The phase dimming decoder has several unique features. The input-output mapping is programmable for design flexibility, while a dynamic filter and variable sampling rate provide smooth uniform dimming. A dynamic hold circuit ensures that the phase dimmer angle is decoded properly while minimizing extra power loss. The LM3450A is identical to the LM3450 with the exception of one circuit operation. The dynamic hold current is sampled in the LM3450 while it continuously operates in the LM3450A. This difference between the two devices defines the suitable applications for each. The following is a general guideline for choosing the correct device: * Any 120V designs with POUT > 15W - LM3450A * Any 230V designs with POUT > 25W - LM3450A * 120V 2-Stage designs with POUT < 15W - LM3450 * 230V 2-Stage designs with POUT < 25W - LM3450 Critical conduction mode PFC Over-voltage protection Feedback short circuit protection 70:1 PWM decoded from phase dimmer Analog dimming Programmable dimming range Digital angle and dimmer detection Dynamic holding current Smooth dimming transitions Low power operation Start-up pre-regulator bias Precision voltage reference Applications Dimmable downlights, troffers, and lowbays Large form factor bulbs Indoor and outdoor area SSL Power supply PFC Typical Application 30127401 (c) 2011 National Semiconductor Corporation 301274 www.national.com LM3450 LM3450A LED Drivers with Active Power Factor Correction and Phase Dimming Decoder LM3450 LM3450A LM3450 LM3450A Connection Diagram Top View 30127402 16-Lead TSSOP NS Package Number MTC16 Ordering Information Order Number Spec. Package Type NSC Package Drawing Supplied As LM3450MT NOPB TSSOP-16 MTC16 92 Units, Rail LM3450MTX NOPB TSSOP-16 MTC16 2500 Units, Tape and Reel LM3450AMT NOPB TSSOP-16 MTC16 92 Units, Rail LM3450AMTX NOPB TSSOP-16 MTC16 2500 Units, Tape and Reel www.national.com 2 Pin 1 Name VREF Description Application Information 3V Reference Reference Output: Connect directly to VADJ or to resistor divider feeding VADJ and to necessary external circuits. Analog Dim and Phase Dimming Range Input: Connect directly to VREF to force standard 70% phase dimming range. Connect to resistor divider from VREF to extend usable range of some phase dimmers or for analog dimming. Connect to GND for low power mode. 2 VADJ Analog Adjust 3 FLT2 Filter 2 Ramp Comparator Input: Connect a series resistor from FLT1 capacitor and a capacitor to GND to establish second filter pole. 4 FLT1 Filter 1 Angle Decoder Output: Connect a series resistor to a capacitor to GND to establish first filter pole. 5 DIM 500 Hz PWM Output Open Drain PWM Dim Output: Connect to dimming input of output stage LED driver (directly or with isolation) to provide decoded dimming command. 6 VAC Sampled Rectified Line Multiplier and Angle Decoder Input: Connect to resistor divider from rectified AC line. 7 COMP Compensation Error Amplifier Output and PWM Comparator Input: Connect a capacitor to GND to set the compensation. Error Amplifier Inverting Input: Connect to output voltage via resistor divider to control PFC voltage loop for non-isolated designs. Connect a 5.11k resistor to GND for isolated designs (bypasses error amplifier). Also includes over-voltage protection and shutdown modes. 8 FB Feedback 9 ISEN Input Current Sense 10 GND Power Ground System Ground 11 CS Current Sense MosFET Current Sense Input: Connect to positive terminal of sense resistor in PFC MosFET source. 12 GATE Gate Drive 13 VCC Input Supply 14 ZCD Zero Crossing Detector Demagnetization Sense Input: Connect a 100k resistor to transformer/inductor winding to detect when all energy has been transferred. 15 HOLD Dynamic Hold Open Drain Dynamic Hold Input: Connect to holding resistor which is connected to source of passFET. 16 BIAS Pre-regulator Gate Bias Pre-regulator Gate Bias Output: Connect to gate of passFET and through resistor to rectified AC (drain of passFET) to aid with startup. Input Current Sense Non-Inverting Input: Connect to diode bridge return and resistor to GND to sense input current for dynamic hold. Connect a 0.1F capacitor and Schottky diode to GND, and a 0.22F capacitor to HOLD. Gate Drive Output: Connect to gate of main power MosFET for PFC. Power Supply Input: Connect to primary bias supply. Connect a 0.1F bypass capacitor to ground. 3 www.national.com LM3450 LM3450A Pin Descriptions LM3450 LM3450A Continuous Power Dissipation Maximum Junction Temperature Storage Temperature Range Maximum Lead Temperature (Solder and Reflow) (Note 2) ESD Susceptibility (Note 3) HBM MM FICDM Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VCC, HOLD, DIM, BIAS HOLD Power BIAS Current ZCD Current COMP, FB, VAC, FLT1, FLT2, VREF, CS, VADJ ISEN GATE -0.3V to 25.0V 250 mW Continuous 5.0mA Continuous +/- 10mA -0.3V to 7.0V -7.0V to 7.0V -0.3V to 18V Continuous -2.5V for 100ns 20.5V for 100ns -1mA to +1mA Continuous Internally Limited Internally Limited -65C to +150C 260C 2kV 200V 750V Operating Conditions (Note 1) VCC Range Junction Temperature Range 8.5V to 20V -40C to +125C Electrical Characteristics (Note 1) Unless otherwise specified VCC = 14V. Specifications in standard type face are for TJ = 25C and those with boldface type apply over the full Operating Temperature Range ( TJ = -40C to +125C). Typical values represent the most likely parametric norm at TA = TJ = +25C, and are provided for reference purposes only. Symbol Parameter Conditions Min (Note 4) Typ (Note 5) Max (Note 4) Units SUPPLY VOLTAGE INPUT (VCC) VCC-RISE Controller Enable Threshold VCC Rising 12.2 13.0 13.6 VCC-FALL Controller Disable Threshold VCC Falling 7.4 7.9 8.5 Glitch Filter Delay 9 Turn-on Delay 40 V s IQ VCC Quiescent Current No Switching 1.6 IQ-SD VCC Shutdown Current VFB = 0V 515 625 A 2.50 2.57 V mA ERROR AMPLIFIER & COMPENSATION (FB, COMP) VFB GM FB Reference (Normal Operation) 2.43 Input Bias Current VFB = 2.5V Transconductance VFB = 2.5V 100 Output Source / Sink Capability FB Pull-up Current Source VFB < 1.8V 115 161 60 85 110 43 51 59 COMP Pull-up Resistor VCMP-B COMP Low Threshold (Burst) VCMP Falling COMP Low Hysteresis VFB-SD Low Threshold (Shutdown) FB Mid Threshold (EA Disabled) VFB Falling 150 VFB Falling 328 5 k V 168 186 346 mV 368 20 FB High Threshold (Over-voltage) COMP Pre-bias Source Current VTHM A VTHM -0.08 20 FB Mid Hysteresis VFB-OV S 20 FB Low Hysteresis VFB-EAD nA 69 1.20 x VFB VCMP = 0.5V Minimum COMP Voltage (Normal) 1.22 x VFB V 415 A 1.47 V ANGLE DEMODULATION & MULTIPLIER (COMP, VAC) VAC-DET VAC Angle Detection Threshold Angle Demodulation Delay Time 334 Both edges 8 VAC Dynamic Input Voltage Range 378 mV s 0 to 5.5 COMP Dynamic Input Voltage Range V VTHM to VTHM +2 VAC Input Impedance www.national.com 356 500 4 k KM Parameter Multiplier Gain (Includes Internal Resistor Divider) Conditions Min (Note 4) VAC = 3V, VCMP = VTHM+1.5V Typ (Note 5) Max (Note 4) 0.5 Units 1/V ZERO CURRENT DETECTOR (ZCD) VZCD-RIS ZCD Input Threshold VZCD Rising Hysteresis 1.45 1.5 1.55 V 150 200 250 mV Delay to Output 135 VZCD-H Positive Clamp Voltage IZCD = 1mA 6.0 VZCD-L Negative Clamp Voltage IZCD = -50A 0.61 ns V PWM COMPARATOR (CS) VOS VLIM PWM Comparator Input Offset Voltage 30 mV PWM Comparator Input Bias Current 20 nA CS Current Limit Threshold 1.40 CS Delay to Output CS Blanking Sinking Impedance tLEB Leading Edge Blanking (LEB) Time 1.50 1.60 V 100 ns 1 k 140 ns ANALOG ADJUST INPUT (VADJ) VADJ-LP VADJ Low Threshold (Low Power Mode) VADJ Falling 56 VADJ Low Hysteresis mV 50 VADJ Pull-up Current Source VADJ Open Voltage 75 VADJ Open 1 A 3 V DYNAMIC HOLD CIRCUIT (HOLD, ISEN) RDSON-HD HOLD MosFET On-Resistance VSEN-REF ISEN Reference Voltage ISEN Short to GND 22 30 42 162 200 232 mV ISEN Bias Current 5 A PRE-REGULATOR GATE DRIVE OUTPUT (BIAS) VBIAS BIAS High Voltage @ 100A VCC < VCC-FALL 18.8 21 22.6 BIAS Low Voltage @ 100A VCC > VCC-RISE 13.5 14 14.5 V GATE DRIVER OUTPUT (GATE) VGATE-H GATE Voltage High IGATE = 20mA 11.5 IGATE = 200mA 10.5 (Note 6) 1.5 GATE Pull Down Resistance GATE Peak Current 2 V 8 A REFERENCE VOLTAGE OUTPUT (VREF) VREF Reference Voltage No Load Current Limit 2.85 3 3.15 V 1.5 2.0 3.0 mA DIMMING OUTPUT (DIM, FLT1, FLT2) FLT1 Output Impedance Standby Mode 500 Transition Mode 1.6 Triangle Waveform Compared to FLT2 High Low fDIM DIM Frequency 180 k 1.49 V 15 mV 460 700 Hz OFF-TIMERS tOFF-MAX Maximum Off-Time (Normal Operation) 340 tOFF-LP Off-Time (Low Power Mode) 42 5 s www.national.com LM3450 LM3450A Symbol LM3450 LM3450A Symbol Parameter Conditions Min (Note 4) Typ (Note 5) Max (Note 4) Units THERMAL SHUTDOWN Thermal Limit Threshold (Note 6) 160 Thermal Limit Hysteresis 20 C THERMAL RESISTANCE JA Junction to Ambient JC Junction to Case TSSOP-16 (Note 6, Note 7) 38.0 10.0 C/W Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed and do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics table. All voltages are with respect to the potential at the GND pin, unless otherwise specified. Note 2: Refer to National's packaging website for more detailed information and mounting techniques. http://www.national.com/analog/packaging/ Note 3: Human Body Model, applicable std. JESD22-A114-C. Machine Model, applicable std. JESD22-A115-A. Field Induced Charge Device Model, applicable std. JESD22-C101-C. Note 4: All limits guaranteed at room temperature (standard typeface) and at temperature extremes (bold typeface). All room temperature limits are 100% production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level (AOQL). Note 5: Typical numbers are at 25C and represent the most likely norm. Note 6: These electrical parameters are guaranteed by design, and are not verified by test. Note 7: Junction-to-ambient thermal resistance is highly board-layout dependent. In applications where high maximum power dissipation exists, namely driving a large MOSFET at high switching frequency from a high input voltage, special care must be paid to thermal dissipation issues during board design. In high-power dissipation applications, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP = 125C for Q1, or 150C for Q0), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the package in the application (JA), as given by the following equation: TA-MAX = TJ-MAX-OP - (JA x PD-MAX). www.national.com 6 TA=+25C and VCC = 14V unless otherwise specified HOLD RDSON vs. Junction Temperature Leading Edge Blanking vs. Junction Temperature 30127415 30127404 Current Limit Threshold vs. Junction Temperature VAC = 3V; VCMP = VTHM + 1.5V Multiplier Gain vs. Junction Temperature VAC = 3V; VCMP = VTHM + 1.5V 30127405 30127406 Transconductance VFB = 2.5V; VFB = 50mV BIAS Voltage vs. Junction Temperature High @ VCC < VCCFALL; Low @ VCC > VCCRISE 30127408 30127407 7 www.national.com LM3450 LM3450A Typical Performance Characteristics LM3450 LM3450A VCC UVLO Threshold vs. Junction Temperature Shutdown Current vs. Junction Temperature 30127410 30127409 VREF Reference vs. Junction Temperature FB Reference vs. Junction Temperature 30127412 30127411 ISEN Reference vs. Junction Temperature VAC Detection Threshold vs. Junction Temperature 30127413 www.national.com 30127414 8 Current Sense Threshold vs. VCOMP and VAC 30127416 30127417 Decoder Mapping from VAC to DIM 1.0 DIM PIN DUTY CYCLE 0.8 0.5V 0.6 0.4 1V 1.5V 0.2 0.0 VADJ=3V 2V 2.5V -0.2 0.0 0.2 0.4 0.6 0.8 1.0 DEMODULATED VAC PIN DUTY CYCLE 30127419 9 www.national.com LM3450 LM3450A Transconductance vs. VFB LM3450 LM3450A Block Diagram 30127421 www.national.com 10 LM3450 LM3450A 30127422 FIGURE 1. Typical Flyback Application PWM output. The PWM output can then be sent directly, or through optical isolation, to the dimming input of a second stage LED driver. To ensure the decoder properly interprets the dimming angle, dynamic hold is provided which prevents the phase dimmer from misfiring. The input current is sensed and when the current drops below a preset minimum, the system adds more current. Both the dynamic hold and the decoder are sampled synchronously in the LM3450 to reduce the overall efficiency drop due to the additional hold current. When a decoding sample period occurs, the dynamic hold is activated to ensure a proper angle is decoded. Because of this sampling method, nonsampled cycles will potentially cause the phase dimmer to misfire but should not affect the output LED current regulation. For higher power applications, where the dynamic hold provides much less current on average, the LM3450A can be used. The LM3450A has continuous dynamic hold which prevents the dimmer from ever misfiring. This is extremely helpful when designing for single stage solutions, where there is no second stage to provide good line rejection. The continuous dynamic hold is also helpful for the higher power two stage applications where the input capacitance is larger. One last feature of the phase decoder is a dynamic filter that, combined with the variable sampling rate, provides fast, smooth dimming transitions. Theory of Operation The LM3450/50A is a single device with both power factor control (PFC) and phase dimming decoder functions. This device is designed to control isolated flyback converters and provide active power factor correction. In addition to being a PFC, the LM3450/50A can interpret a phase dimming (frequently called triac dimming) input and provide a corresponding PWM output to properly dim an LED load. This combination of features provides an excellent method to convert a standard AC mains input to a dimmable LED output of 10-100W. It should be noted that the LM3450/50A can control a boost converter in a similar manner. However, this datasheet will focus mostly on the flyback topology due to the high demand for isolated LED driver applications. Discussion of the LM3450/50A functionality will refer to Figure 1 component designators. The PFC control operates in critical conduction mode (CRM) using zero crossing detection (ZCD) to terminate the off-time. The PFC portion of this device includes an error amplifier, multiplier, current sense circuit, zero crossing detector, and gate driver. The internal error amplifier is used for feedback of the output voltage in non-isolated designs. However, it can be disabled for isolated designs where the error amplifier needs to be on the secondary side. The phase dimmer decoder detects the dimming angle of the rectified AC line, decodes, filters and remaps it to a 500Hz 11 www.national.com LM3450 LM3450A 30127423 FIGURE 2. PFC System Architecture quency content is removed with large energy storage capacitance at the output. Using this control architecture, the converter is able to provide two important functions at the same time: * Shape the input current * Regulate the output voltage The PFC control approach requires two separate control loops to achieve both functions: a fast loop which shapes the input current, and a slow loop that regulates the output voltage. The fast control loop shapes the input current to have the same sinusoidal shape as the AC input voltage. Assuming both are perfect sinusoids with zero distortion or phase shift, the power factor will be perfect (unity). Unfortunately, distortion is always present in switching converters. An input filter, which is required to comply with EMI standards, helps to attenuate the switching content, thereby reducing distortion. However, the added filter capacitance will increase the phase shift at the same time. Though perfect PF is not achievable within real applications, extremely high PF (>.99) is possible using most active PFCs. The output voltage has to be regulated slowly to ensure the converter ignores the twice line frequency ripple present on the output. Therefore, the voltage loop containing the error amplifier should have a bandwidth at least an order of magnitude slower (<20Hz is common). Sometimes the bandwidth is increased to improve transient response, which is the case with off-line dimmable LED drivers. Though PF decreases with the increase in bandwidth, high PF (>.95) is still possible. PFC BACKGROUND Power factor (PF) is a number between 0 and 1 that indicates how well energy is transmitted from input to output of a system. It can be described by average power (PAVG), RMS voltage (VRMS), and RMS current (IRMS): Or by distortion factor (KDIST) and displacement factor (KDISP): With a purely resistive system, PF = 1. The addition of reactive elements necessary in any converter, such as EMI filters and energy storage, will induce some amount of displacement (phase shift between the input voltage and input current). The addition of switching devices will also create distortion (energy present in the harmonics relative to the switching frequencies). These non-idealities decrease the PF towards zero. Active power factor correction attempts to make the input impedance look as resistive as possible to the power source. Since the output of the converter is usually a regulated voltage or current, there is a need for large energy storage elements to remove the twice line frequency (100Hz or 120Hz) ripple. A power factor control architecture, as shown in Figure 2, has very little capacitance at the input. Instead, the twice line fre- www.national.com 12 LM3450 LM3450A 30127424 FIGURE 3. Basic CRM Inductor Current Waveform peak current envelope (IS-pk) will simply be a scaled version of the primary according to the turns ratio of the transformer. Assuming good attenuation of the switching ripple via the EMI filter, the average input current (IIN), represented by the red line in Figure 4, can also be approximated as a sinusoid proportional to the duty cycle (D(t)): CRM BACKGROUND During critical conduction mode (CRM), a converter operates at the boundary of continuous conduction mode (CCM) and discontinuous conduction mode (DCM). This is usually implemented as follows. The main switching MosFET (QSW) is turned on and the inductor current rises to a peak threshold. QSW is then turned off and the current falls until it reaches zero. At this point, QSW is turned on and the cycle repeats. Near zero voltage switching, enabled by the inductor current return to zero, gives CRM topologies an efficiency improvement compared to CCM topologies. Figure 3 shows the resulting inductor current waveform, where the average inductor current (IL) is half of the peak current (IL-MAX). In a CRM flyback PFC application, the rectified AC input is fed forward to the control loop, creating a sinusoidal primary peak current envelope (IP-pk) as shown in Figure 4. The secondary Since CRM operation is hysteretic and the input voltage is fedforward, the input current shaping loop is as fast as possible. Only the output voltage needs to be regulated with a narrow bandwidth error amplifier, which greatly simplifies the system dynamics. 30127425 FIGURE 4. CRM Flyback Current Waveforms 13 www.national.com LM3450 LM3450A 30127426 FIGURE 5. PFC Control Circuit Once QSW is turned off, the LM3450/50A waits until the inductor (boost) or transformer (flyback) is demagnetized to turn QSW on again. Demagnetization, sensed at ZCD, occurs when the current through the magnetic component falls to zero. Since the output voltage is regulated, the slope of the current remains relatively constant and, coupled with the variable peak detect, creates a variable off-time. The sinusoidal peak detection envelope creates an input current that is sinusoidal and in phase with the input voltage providing excellent PF. The PWM comparator 30mV input offset voltage ensures current is drawn at the zero-crossings of the AC line, reducing distortion and further improving PF. POWER FACTOR CONTROLLER The LM3450/50A uses CRM control to regulate the output voltage and provide power factor correction. In a non-isolated boost topology, an external voltage divider (RFB1, RFB2) is used to sense the output voltage, as shown in Figure 5. The divider is connected to the inverting input (FB) of the internal error amplifier. The LM3450/50A regulates the feedback voltage (VFB) to 2.5V in a closed loop fashion. The FB pin has a shutdown mode to protect against a feedback short and an OVP mode which terminates switching when output over-voltage is sensed. With the FB shutdown mode, it is necessary to have a preliminary biasing method for the output of the error amplifier (COMP). Otherwise, the converter would never start. COMP is pre-biased with a 415A current until the voltage at COMP (VCMP) exceeds the minimum operational voltage (VTHM). For an isolated flyback topology, where the error amplifier is on the secondary, the LM3450/50A internal error amplifier can be bypassed using a single 5.11k resistor (RFB1) from FB to GND. This engages an internal 5k pull-up resistor at COMP. COMP can then be connected directly to the optical isolation as shown in Figure 5. COMP and the sensed rectified AC input voltage (VAC), provided via a resistor divider (RAC1, RAC2), are inputs to the multiplier. The current through the sense resistor (RCS) produces a voltage (VCS) that is compared to the multiplier output. When VCS exceeds the multiplier output, QSW is turned off. The peak detect threshold and the current slope during an on-time are proportionally changing which yields a nearly constant on-time, shown in Figure 4: CURRENT SENSE The LM3450/50A senses current through QSW via a sense resistor (RCS) between the source of QSW and GND. When VCS exceeds the output of the multiplier (VMLT), QSW is turned off. VMLT is variable over the line cycle and is a function of the scaled rectified AC voltage (VAC), the COMP voltage referenced from its operational minimum (VCOMP-VTHM), the multiplier gain (KM) and the PWM comparator offset (VOS): The LM3450/50A has a leading edge blanking (LEB) circuit that pulls the current sense input to the PWM comparator low for 140s at the beginning of each on-time. The LEB blanks the current spike and associated ringing due to the turn-on transient of QSW, limiting the minimum achievable duty cycle. OVER CURRENT PROTECTION The LM3450/50A has a current limit threshold (VLIM = 1.5V) at CS to protect the system from over-current conditions. If VCS exceeds VLIM, QSW is immediately turned off until ZCD triggers a new on-time. www.national.com 14 30127427 FIGURE 6. ZCD Waveforms for Flyback Design SECONDARY ERROR AMPLIFIER For isolated designs, the error amplifier on the secondary should take the form of a proportional integral (PI) compensator. The amplifier is frequently implemented with an LMV431. The output voltage resistor divider (RFB1, RFB2) provides the sensed output voltage to the LMV431 inverting input. The PI compensation is achieved by connecting RSC and CSC in between the LMV431 input and output, shown in Figure 7. In addition, CCMP is placed from COMP to GND on the primary for higher frequency noise attenuation. In addition to the basic error amplifier, a soft-start circuit can be implemented using a capacitor, two diodes and a Zener diode as shown in Figure 7. This secondary softstart circuit has no restart mechanism, therefore a primary side softstart is recommended as described in the SOFTSTART section of this document. ZERO CURRENT DETECTION ZCD is implemented with a 100k resistor from the ZCD pin to a coupled winding on the transformer or inductor as shown in Figure 5. This winding is also used to bootstrap VCC after start-up. When QSW turns off, the voltage at the ZCD pin (VZCD) increases as energy is transferred through the auxiliary winding. The circuit arms when VZCD exceeds 1.5V. Then, when the energy is fully transferred, VZCD decreases towards zero. When VZCD falls below 1.3V, the transformer is assumed to be demagnetized, the circuit disarms, and QSW is turned back on as shown in Figure 6. The ZCD pin voltage will remain low until QSW is turned off via peak detection and the cycle repeats. SWITCHING FREQUENCY With a constant on-time and variable off-time, there is a variable switching frequency: Figure 4 shows that the minimum switching frequency occurs at the peak of the rectified AC waveform, while the maximum switching frequency occurs at the valley. ERROR AMPLIFIER The LM3450/50A internal error amplifier is used for non-isolated designs (boost) where the output voltage can be directly sensed, via a resistor divider, at the FB pin. The FB pin is the inverting input of the trans-conductance amplifier which is regulated to 2.5V. The COMP pin is the output of the amplifier and external compensation is placed from COMP to GND in the form of a single capacitor (CCMP) as shown in Figure 5, a series resistor and capacitor, or both. The output of the amplifier sources or sinks current as necessary to force the inputs of the amplifier to be equal. The compensation method depends upon the transient performance desired and requires a loop gain analysis. This analysis can be somewhat complex and cumbersome. A detailed analysis can be found Application Notes AN-2098 and/or AN-2150. 30127428 FIGURE 7. Secondary Error Amplifier 15 www.national.com LM3450 LM3450A If the COMP pin voltage (VCMP) falls below 1.4V at any time, the device enters burst mode where the GATE is off for 340s then is turned on. If VCMP is still below 1.4V at the end of the on-time then another 340s off-time occurs. However, if VCMP has risen above 1.4V, the converter continues switching until it falls below the threshold again. This feature is necessary to prevent the output of the converter from rising arbitrarily high because the minimum on-time of the device prevents less energy transfer. The LM3450/50A also implements both feedback short circuit protection and output over-voltage protection (OVP) functions at the FB pin. If VFB exceeds 3V, then OVP is engaged and the part stops switching until VFB falls below 3V. In the same manner, if VFB falls below 168mV, then shutdown is engaged and switching stops until VFB exceeds 188mV. The flyback topology is frequently used to provide isolation from input to output. Since, the current transfer ratio (CTR) of standard optical isolation varies over temperature, proper regulation using primary error amplifiers is difficult. An error amplifier is usually placed in the secondary to regulate the output voltage accurately. To accommodate isolated designs, the LM3450/50A internal error amplifier can be bypassed by placing a 5.11k resistor from FB to GND. This engages a 5k pull-up resistor from COMP to an internal 5V rail. LM3450 LM3450A PHASE DIMMER OPERATION A simplified schematic of a phase dimmer is shown in Figure 9. An RC network consisting of R1, R2, and C1 delay the turnon of the triac until the voltage on C1 reaches the trigger voltage of the diac. Increasing the resistance of the potentiometer (wiper moving downward) increases the turn-on delay which decreases the on-time or "conduction angle" of the triac (). This reduces the average power delivered to the load. PRECISION VOLTAGE REFERENCE The LM3450/50A provides a 3V voltage reference (VREF) for biasing the VADJ pin as well as any external circuitry. VREF is regulated once VCC exceeds 3V. There is a 2mA current limit for the reference. A 10nF ceramic bypass capacitor should be placed from VREF to GND. LOW POWER SHUTDOWN The LM3450/50A can be placed into a low power shutdown by grounding the VADJ pin (any voltage below 75mV). During low power shutdown, the device will turn on the GATE for one cycle followed by a fixed off-time of 42s and the cycle repeats. During shutdown, the DIM output will be high (zero light output) since the buffer rail at FLT1 will be at or near zero. This feature is designed to hold up the PFC output voltage while removing the load (turning the LEDs off). THERMAL SHUTDOWN Internal thermal shutdown circuitry is provided to protect the IC in the event that the maximum junction temperature is exceeded. The threshold for thermal shutdown is 160C with a 20C hysteresis. During thermal shutdown GATE is disabled. 30127429 FIGURE 9. Basic Forward Phase Dimmer Phase dimmer voltage waveforms are shown in Figure 8. Figure 8a shows the full sinusoid of the input voltage. Even when set to full brightness; few dimmers will provide 100% conduction angle. Figure 8b shows a waveform from a forward phase dimmer. The off-time can be referred to as the firing angle and is simply 180 - . Figure 8c shows the waveform of a reverse phase dimmer (also called an electronic dimmer in the lighting industry). These typically or more expensive, microcontroller based dimmers that use switching devices other than triacs. Note that the conduction angle starts from the zero-crossing, and terminates some time later. This method of control reduces the noise spike at the transition. Any form of phase dimming modulates the incoming AC waveform by chopping part of the sinusoid, reducing the average power to the load. These dimmers work very well with standard incandescent bulbs, but not with power converters. A converter attempts to regulate the load in with presence of any input, effectively ignoring the phase angle. To implement a dimmable converter, the angle must be sensed at the input, decoded and used to properly control the LED current regulator. 30127430 FIGURE 8. Phase Dimming Waveforms www.national.com 16 LM3450 LM3450A 30127431 FIGURE 10. Dimming Decoder Circuit of low dimming levels to the human eye. A minimum duty cycle limits the maximum achievable contrast ratio to approximately 70:1. The remapped PWM signal is buffered and output at FLT1 with amplitude equal to VADJ as shown in Figure 12. PHASE DIMMING DECODER The LM3450/50A uses the rectified AC line voltage to interpret the conduction angle. Figure 10 shows the LM3450/50A decoder circuit with associated external circuitry. The rectified AC line voltage is scaled via a resistor divider (RAC1, RAC2) and connected to the VAC pin. VAC is compared to a 356mV reference to generate a twice line frequency PWM signal with corresponding duty cycle as shown in Figure 11. 30127433 FIGURE 12. FLT1 to FLT2 Mapping The FLT1 signal is routed through a 2 pole low pass filter (RF1, CF1, RF2, CF2), as shown in Figure 10, to remove the twice line frequency ripple. The resulting analog signal at FLT2 is compared to a 500Hz Triangle wave to create the inverted PWM signal at the DIM pin as shown in Figure 13: 30127432 FIGURE 11. Phase Angle Demodulation For best results, RAC1 and RAC2 are suggested to be sized so that the VAC voltage crosses the 356mV threshold when the rectified AC line is as follows: * 120V systems: 25V to 45V * 230V systems: 40V to 70V The demodulated duty cycle is sampled and logarithmically remapped to a 300Hz PWM signal improving the resolution 30127434 FIGURE 13. FLT2 to DIM Mapping 17 www.national.com www.national.com 1.2 DIM PIN DUTY CYCLE (INVERTED) LM3450 LM3450A This PWM signal at the DIM pin can be used as the dim input to a secondary LED driver. DIM is an open drain output designed for isolated solutions. Optical isolation is used to transmit signals across the isolation boundary. With most optoisolators, the edge rate is dependent on the amount of drive current through the photodiode. The open-drain configuration allows the primary bias supply (VCC) to provide the current as shown in Figure 10. The choice of resistor (RPB) between VCC and the photodiode anode will set the drive current. This enables the user to trade-off PWM accuracy with system efficiency. The open drain configuration also ensures that the secondary has a resistor from the phototransistor's emitter to secondary ground (not from collector to secondary bias). During system turn-off, this prevents an undesired LED blink because the secondary stage LED driver is forced off. A variable sample rate and dynamic filter ensure fast, smooth dimming transitions (movement of the dimmer) while maintaining robust flicker-free behavior when the dimmer is static. The sample rate depends on past and present angle information. The dynamic filter is a dual mode filter. During standby mode, when a transition has not been made and the dimmer is static, a 500k series resistor is connected between the buffered output and FLT1 as shown in Figure 10. The 500k resistor is shorted when the LM3450/50A senses a large transition of the dimmer. This increases the filter speed while the dimmer is transitioning between levels to improve response time. The FLT1 and FLT2 poles created by each RC pair (RF1 and CF1, RF2 and CF2) should be set as follows: * CF1 and CF2 can be 1F ceramic capacitors for all designs. * RF1 and RF2 should be set between 15k (~10Hz) and 75k (~2Hz). 2 Hz poles provide a "smooth fade" while 10Hz poles create a "snappy" response. These component values ensure that the static filter condition in standby mode has 1 pole approximately a decade lower than the nominal in order to provide good noise immunity to the system. 1.0 VADJ=3V 2.5V 0.8 0.6 0.4 2V 1.5V 1V 0.2 0.0 0.5V 0.0 0.2 0.4 0.6 0.8 1.0 LM3450/A DEMODULATED VAC PIN DUTY CYCLE 30127418 FIGURE 14. Complete Decoder Mapping Since the buffered decoder output has amplitude equal to VADJ and the resulting PWM signal is filtered into an analog voltage at FLT2, the VADJ pin can be used to change the mapping as shown in Figure 14. The maximum LED current (DIM = 0) when VADJ = 3V corresponds to decoded angles of 70% or greater. Some dimmers have a maximum angle greater than this. If VADJ is reduced to 2.5V, the maximum LED current will correspond to an angle of 80% and at VADJ = 2V the maximum will occur at a decoded angle of 95%. The VADJ pin can also be used to implement a standard analog adjust function. If the demodulated phase angle at VAC is above 85%, then the fast filter is always enabled (500k shorted) and the VADJ pin can solely be used to scale the DIM pin duty cycle. When VADJ is pulled below 75mV the part enters low power shutdown so the maximum attainable contrast ratio using VADJ only is approximately 40:1. Both FLT1 and FLT2 have pull-down MosFETs that are turned on when VCC UVLO falling threshold is triggered. This provides a quick discharge path for the capacitors and eliminates the possibility of an undesired light level at the next startup. 18 LM3450 LM3450A 30127435 FIGURE 15. Dynamic Hold Circuit adds holding current via the HOLD circuitry to maintain 200mV across RSEN. The hold current is added by linearly adjusting the gate voltage of QHLD as shown in Figure 15. As the gate voltage of QHLD is increased, the HOLD pin voltage decreases, forcing a voltage across the resistance (RHLD) from the source of QPS to HOLD. This extra current is drawn from the input through the triac, but is not processed by the converter. Figure 17 shows a typical dynamic hold waveform of the LM3450 where interval 1 is a non-sampled conduction angle, 2 is the firing angle, and 3 is a sampled conduction angle. It should be noted that using the LM3450A will ensure every conduction angle looks like interval 3 in Figure 17. DYNAMIC HOLD A forward phase "triac" dimmer requires a minimum amount of current to be flowing through it during the entire conduction angle. This is referred to as hold current. If the minimum hold current requirement is not met, the triac will shut off (misfire). During normal operation, the converter will demand some amount of input current. However, at any point during the cycle, the input current can be low enough to cause a misfire. During an LM3450/50A sampling period, the triac should not misfire or the decoded angle will be inaccurate as shown in Figure 16. Since the triac is asymmetrical phase-to-phase, misfires can occur at different points in the waveform. After the triac misfires, the voltage returns to zero exponentially. This can create a large difference between decoded angles which can be observed as a "fluttering" of the light. 30127437 FIGURE 17. Dynamic Hold Waveform 30127436 The dynamic hold function is also necessary for reverse phase dimmers, but for a different reason. Reverse phase dimmers do not use triacs, therefore they do not require a minimum "holding" current. Instead, they need what is commonly called bleeder current. When a reverse phase dimmer turns off, the AC voltage is at a high value. There is an RC time constant associated with discharging the total effective input capacitance (EMI capacitors, PFC capacitor, damper FIGURE 16. Forward Phase Waveform To ensure the triac does not misfire during a sampling period and the angle is correctly decoded, a dynamic hold function is enabled. The input current is sensed with a resistor (RSEN) from GND to ISEN (the return of the full bridge rectifier). If the voltage across this resistor is less than 200mV, the device 19 www.national.com LM3450 LM3450A cuit to well below the switching frequency. However, if too large a capacitor is used, the bandwidth will be too low to respond to line transients. A maximum of 0.47F should ensure good performance. Finally, a small Schottky diode should be placed from GND to ISEN to absorb the large current spikes associated with the triac firing edge. This diode should have a forward voltage above 200mV at the worst-case operating temperature so that it won't interfere with dynamic hold regulation. capacitance). The decoder does not record the angle until the voltage reaches the 356mV threshold. This can cause the decoded angle to be much larger than it actually is and dependent on the RC time constant as shown in Figure 18. THERMAL PROTECTION With the LM3450A, QPS has to dissipate more power than with the LM3450. During worst case conditions such as open LED load, the converter will be demanding very little current regardless of the triac position. If the phase dimmer conduction angle is large and the load is not present, QPS has to dissipate many watts since the dynamic hold is attempting to regulate the current to ten's of mA. Using the LM3450, this is nominally not a problem since it is sampling the dynamic hold infrequently. However, the LM3450A is drawing the hold current every cycle which becomes a problem very quickly. It should be noted that If the input AC line is very noisy, the VAC input to the decoder could have enough variation in steady state to cause the decoder to think the dimmer is transitioning all of the time. This would increase the sampling rate dramatically, putting much more thermal strain on the passFET in LM3450 applications as well. To mitigate these problems, a thermal protection circuit should be implemented on the LM3450A designs (and can be on the LM3450 designs as well) as shown in red in Figure 15. The NTC thermistor should be placed on the opposite side of the PCB directly under the drain of QPS. This will provide the best thermal coupling while maintaining the necessary high voltage spacing constraints. At startup the NTC is at a high resistance value, turning the PNP fully on which provides the dynamic hold path. As the NTC heats up the resistance decreases and the base voltage increases. Eventually, the PNP will transition into linear mode and the effective resistance from collector to emitter will increase. This will decrease the maximum holding current, thereby decreasing the thermal stress on QPS. Given enough headroom, the circuit should reach thermal equilibrium in a safe controlled manner. Since this method of thermal protection linearly reduces the maximum hold current with increasing temperature, the foldback will not be perceptible to the consumer. Instead, the result of the foldback will simply be a reduction of contrast ratio, meaning the minimum achievable LED current will increase as the temperature increases beyond the foldback level. 30127438 FIGURE 18. Reverse Phase Waveforms The dynamic hold will quickly bleed off the excess charge in an attempt to regulate the voltage across RSEN. This will preserve the accuracy of the decoded phase angle. During the conduction angle (), dynamic hold is enabled only during a sample period for the LM3450. However, during the firing angle (delay time), dynamic hold is always enabled with the LM3450. This will ensure the rectified line voltage does not begin to rise due to leakage currents through the phase dimmer. Again, with the LM3450A the dynamic hold is continuously active during all conduction and firing angles. The minimum regulated input current can be calculated: The maximum possible additional holding current (which can occur when HOLD is still transitioning usually at the rising edge of the triac firing) can be approximated: It is recommended that the maximum hold current is set 10-15% higher than the minimum regulated input current. A minimum of 0.1F capacitance should be placed between ISEN and HOLD to limit the bandwidth of the dynamic hold cir- www.national.com 20 LM3450 LM3450A 30127439 FIGURE 19. Primary Bias Circuitry PRIMARY BIAS SUPPLY The LM3450/50A requires a supply voltage at VCC, not to exceed 25V. The device has VCC under-voltage lockout (UVLO) with rising and falling thresholds of 12.9V and 7.9V respectively. A 24V Zener diode should be placed from the VCC pin to GND to protect the device from substantial spikes that could cause damage. Figure 19 shows how the LM3450/50A provides a quick way to generate the necessary primary bias supply at start-up. Since the AC line peak voltage is always higher than the rating of the controller, all designs require an N-channel MosFET (passFET). The passFET (QPS) is connected with its drain attached to the rectified AC. The gate of QPS is connected to the BIAS pin which has a stack of 2 Zener diodes internal to the device. These diodes are then biased from the rectified AC line through series resistance (RBS). The source of QPS is held at a VGS below the Zener voltage and current flows through QPS to charge up whatever capacitance is present. If the capacitance is large enough, the source voltage will remain relatively constant over the line cycle and this becomes the input bias supply at VCC. This bias circuit enables instant turn-on. However, once the circuit is operational it is desirable to bootstrap VCC to an auxiliary winding of the inductor or transformer (also used for ZCD). The two bias paths are each connected to VCC through a diode to ensure the higher of the two is providing VCC current. This bootstrapping greatly improves efficiency when quick start-up is necessary. To ensure that the auxiliary winding is powering VCC at all times except start-up, the LM3450/50A has a dual BIAS mode. The BIAS voltage at startup is 20V through two Zener diodes. When the VCC UVLO rising threshold is exceeded and the device turns on, the BIAS pin voltage is reduced to 14V (bottom 6V Zener is shorted). Once the VCC UVLO falling threshold is reached again, the BIAS pin will return to 20V to attempt to restart the device. It should be noted that the large hysteresis of VCC UVLO and the dual BIAS mode allow for a large variation of the auxiliary bias circuitry easing the design of the magnetics. SOFTSTART As in any off-line system, softstart is an important part of the design. Since the LM3450/50A are used with phase dimming applications, the typical startup problems are magnified since a phase dimmer is frequently turned on and off rapidly. This requires a softstart mechanism that quickly resets when the LM3450/50A turns off. Since the LM3450/50A has two distinct functional parts (PFC and phase decoder), ideally both should be softstarted simultaneously. This will ensure the most controlled start-up possible. The circuit in Figure 20 provides this exact functionality. Both VADJ and COMP are diode or'ed into an RC charging circuit fed from VCC. The reset mechanism is accomplished using an 18V Zener from BIAS, a current limiting resistor and an NPN transistor. The reset is activated when VCC uvlo falling is triggered and BIAS transitions to 20V. This discharges the RC to zero and as soon as VCC uvlo rising is passed BIAS transitions to 14V again, releasing the clamp on the RC softstart circuit. The RC will charge up to the 3.9V Zener clamp (which is above the dynamic range of COMP and VADJ and become effectively out of the circuit until the next turn-off. 30127450 FIGURE 20. Dual Softstart Circuit 21 www.national.com LM3450 LM3450A The designer must pay close attention to the power loss of the passFET when using the LM3450A. Designers must consider worst case possibilities with any power conversion designs. Worst case operating conditions with the LM3450A are usually found with the largest triac holding current requirements. Many phase dimmers require 25mA-40mA of holding current, and frequently designers are choosing 50mA as their minimum holding current requirement. The passFET package for common LM3450/50A designs should be capable of dissipating between 1W and 1.5W. The pass-FET can always be increased in size and/or the hold current can be reduced. Power calculations for the dynamic hold circuit as well as effective thermal protection are both described in the DYNAMIC HOLD section. The LM3450 and LM3450A is best differentiated in terms of the appropriate applications for each device. The Device Selection Guide can be used as a general guide for when to use each part. Design Information HOW TO SELECT THE CORRECT DEVICE (LM3450 or LM3450A) What application(s) are suitable for the LM3450, and when is the LM3450A appropriate? The difference centers on the power dissipation in the passFET. The passFET stands off the high AC voltage from the LM3450/50A, and provides a path for the hold current. The passFET operates in the linear region and dissipates power equal to the product of the voltage across it and the current through it. The LM3450 was designed to minimize the power dissipation in the passFET by applying holding current in a sampled form. The standby sampling rate (when the dimmer is not moving) is infrequent, allowing minimal impact on the thermal considerations of the passFET. Sampling of the dynamic hold is not desired for some applications although. An example where the sampled hold current may cause undesirable effects is the single stage flyback topology where the output of the flyback is directly connected to the LEDs. If the phase dimmer is allowed to misfire or create erratic differences in the input voltage and current waveforms, this behavior will appear as a "fluttering" of the LED light output at the sampling rate when the single stage topology is used. The light flutter is most observable at low input currents (dimming). A small perturbation in the input voltage due to phase dimmer misfire can create a visible difference in the output light. Using a secondary LED driver stage eliminates this problem. Cost sensitive applications may drive the design to a single stage solution, and the LM3450A was developed to address this market. The LM3450A provides continuous dynamic hold current on every AC cycle preventing the phase dimmer from misfire, and the sampling frequency from appearing at the output. Another design consideration where continuous dynamic hold may be advantageous is the reduced stresses on input EMI R/C snubber networks. www.national.com Device Selection Guide Product AC Input 120V High End Downlight 230V Low Cost Downlight or Large High End Bulb 22 120V 230V Output Power Device POUT < 15W LM3450 POUT > 15W LM3450A POUT < 25W LM3450 POUT > 25W LM3450A Topology Two Stage Design POUT > 15W POUT > 25W LM3450A Single Stage Design LM3450 LM3450A Applications Information See AN-2098 and/or AN-2150 for detailed design and application information. TWO STAGE LED DRIVER - LM3450 PRIMARY AND LM3409HV SECONDARY 30127440 23 www.national.com LM3450 LM3450A 15W TWO STAGE DESIGN SPECIFICATIONS AC Input Voltage: 120VAC nominal (90VAC - 135VAC) or 230VAC nominal (180VAC - 265VAC) Regulated Flyback Output Voltage: 50V Regulated LED Current: 350mA LED Stack Voltage Maximum: 45V Bill of Materials *Components are used in both versions unless otherwise noted Reference Designator Description Manufacturer Part Number LM3450 IC PFC CONT 16-TSSOP NSC LM3450MT LM3409HV IC LED DRIVR 10-eMSOP NSC LM3409HVMY LMV431 IC SHUNT REG SOT-23 NSC LMV431AIM5 120V CAP CER 0.22F 250V 1210 MURATA GRM32DR72E224KW01L 230V C1a, C1b, C5a, C5b CAP CER 68nF 250V 1210 MURATA GRM32QR72E683KW01L C2 CAP MPY 33nF 250VAC X1 RAD EPCOS B32912A3333M C3 CAP CER 47F 6.3V 0805 TAIYO YUDEN JMK212BJ476MG-T 120V CAP MPY 0.1F 400V RAD EPCOS B32612A4104J008 230V C4 CAP MPY 33nF 1000V RAD WIMA MKP10 - .033/1000/10 C6 CAP CER 4.7nF 500VAC Y1 RAD EPCOS VY1472M63Y5UQ63V0 C7a CAP ELEC 470F 63V RAD NICHICON UPW1J471MHD3 C7b, C8b, C9b, C11, C15 CAP CER 0.1F 50V 1206 MURATA GRM188R71H104KA93D C8a, C9a CAP ELEC 100F 50V RAD NICHICON UHE1H101MPD C10 CAP CER 10nF 25V 0603 MURATA GRM188R71E103KA01D C12, C13 C14, C21 CAP CER 1F 16V 0603 MURATA GRM188R71C105KA12D C16 CAP CER 0.22F 16V 0603 TDK C1608X7R1C224K C17 CAP CER 10F 16V 1206 MURATA GRM31CR71C106KAC7L C18, C20 CAP CER 1F 100V 1206 TDK C3216X7R2A105M C19 CAP CER 2.2F 6.3V 0603 TDK C1608X5R0J225M C22 CAP CER 470pF 100V 0603 TDK C1608C0G2A471J 120V DIODE ULTRAFAST 200V 1A SMA FAIRCHILD ES1D 230V D1 DIODE FAST 400V 1A DO-214AC FAIRCHILD ES1G D2 DIODE ULTRAFAST 200V 1A SMA FAIRCHILD ES1D D3, D5 DIODE ULTRAFAST 100V 0.2A SOT-23 FAIRCHILD MMBD914 D4 DIODE DUAL SCHOTTKY 20V 0.5A SOT-23 NXP SEMI PMEG3005CT,215 120V DIODE TVS 150V 600W UNI SMB LITTLEFUSE SMBJ150A 230V DIODE TVS 220V 600W UNI SMB LITTLEFUSE SMBJ220A D7 DIODE ULTRAFAST 600V 1A SMA FAIRCHILD ES1J D8 DIODE ZENER 24V 1.5W SMA MICRO-SEMI SMAJ5934B-TP D9 DIODE SCHOTTKY 20V 3A SMA FAIRCHILD ES2AA-13-F D10 DIODE RECT 600V 0.5A Minidip COMCHIP HD06 D11, D12 DIODE ZENER 10V 500mW SOD-123 FAIRCHILD MMSZ5240B D13 DIODE ULTRAFAST 70V 0.2A SOT-23 FAIRCHILD BAV99 D14 DIODE ZENER 3.3V 500mW SOD-123 ON-SEMI MMSZ3V3T1G D15 DIODE ZENER 1.8V 500MW SOD-123 ON-SEMI MMSZ4678T1G D16 DIODE SCHOTTKY 60V 2A SMB ON-SEMI SS26T3G D17 DIODE ZENER 3.9V 500MW SOD-123 ON-SEMI MMSZ4686T1G D18 DIODE ZENER 18V 500MW SOD-123 ON-SEMI MMSZ5248T1G L1, L2, L3 IND SHIELD 1mH 0.46A SMT COILCRAFT MSS1038-105KL L4 IND SHIELD 470H 1.06A SMT COILCRAFT MSS1278-474KLB Q1 MOSFET N-CH 800V 3A DPAK ST MICRO STD4NK80ZT4 D6 www.national.com 24 Description Manufacturer Part Number Q2 120V MOSFET N-CH 600V 4.4A DPAK INFINEON IPD60R950C6 230V MOSFET N-CH 800V 3A DPAK ST MICRO STD4NK80ZT4 Q3, Q4 TRANS NPN 40V 0.6A SOT-23 FAIRCHILD MMBT4401 Q5 MOSFET P-CH 70V 5.7A DPAK ZETEX ZXMP7A17K Q6 TRANS PNP 40V 0.2A SOT-23 FAIRCHILD MMBT3904 120V RES 330 5% 1W 2512 VISHAY CRCW2512330RJNEG 230V R1 R2 RES 510 5% 1W 2512 VISHAY CRCW2512510RJNEG 120V RES 430 5% 1W 2512 VISHAY CRCW2512430RJNEG 230V RES 1.6k 5% 1W 2512 VISHAY CRCW25121K60JNEG 120V RES 402k 1% 0.25W 1206 VISHAY CRCW1206402KFKEA 230V RES 953k 1% 0.25W 1206 VISHAY CRCW1206953KFKEA R4 RES 100 1% 1W 2512 VISHAY WSL2512100RFKEA R5 RES 100k 1% 0.1W 0603 VISHAY CRCW0603100KFKEA R6 RES 6.04k 1% 0.1W 0603 VISHAY CRCW06036K04FKEA R7 RES 499k 1% 0.1W 0603 VISHAY CRCW0603499KFKEA R8, R9 RES 75.0k 1% 0.1W 0603 VISHAY CRCW060375K0FKEA RES 20.0k 1% 0.1W 0603 VISHAY CRCW060320K0FKEA RES 1.00M 1% 0.25W 1206 VISHAY CRCW12061M00FKEA RES 2.00M 1% 0.25W 1206 VISHAY CRCW12062M00FKEA R3 R10 R11 120V 230V R12 RES 15.0k 1% 0.1W 0603 VISHAY CRCW060315K0FKEA R13 RES 5.11k 1% 0.1W 0603 VISHAY CRCW06035K11FKEA R14a RES 10 1% 0.25W 1206 VISHAY CRCW120610R0FKEA R14b RES 1.00 1% 0.33W 1210 VISHAY CRCW12101R00FNEA R15a, R15b RES 5.62 1% 0.25W 1206 VISHAY CRCW12065R62FNEA R16 R17 RES 2.00k 1% 0.125W 0805 VISHAY CRCW08052K00FKEA 120V RES 20.0k 1% 0.1W 0603 VISHAY CRCW060320K0FKEA 230V RES 10.0k 1% 0.1W 0603 VISHAY CRCW060310K0FKEA R18 RES 105k 1% 0.125W 0805 VISHAY CRCW0805105KFKEA R19 RES 2.67k 1% 0.1W 0603 VISHAY CRCW06032K67FKEA R20 RES 6.04k 1% 0.125W 0805 VISHAY CRCW08056K04FKEA R21 RES 10.0k 1% 0.125W 0805 VISHAY CRCW080510K0FKEA R22 RES 80.6k 1% 0.1W 0603 VISHAY CRCW060380K6FKEA R23 RES .62 1% 0.5 2010 SMD ROHM MCR50JZHFLR620 R24, R25 R27, R28 RES 10k 1% 0.1W 0603 VISHAY CRCW060310K0FKEA 120V RES 10 10% 2W FILM WELWYN EMC2-10R0 230V RES 22 10% 2W FILM WELWYN EMC2-22R0 OPTO-ISOLATOR SMD LITE ON CNY17F-3S 120V XFORMER 120V 15W OUTPUT 50V WURTH 750813550 230V XFORMER 230V 15W OUTPUT 50V WURTH 750817550 OPTO1, OPTO2 T1 25 LM3450 LM3450A Reference Designator www.national.com LM3450 LM3450A SINGLE STAGE LED DRIVER - LM3450A FLYBACK 30127441 www.national.com 26 LM3450 LM3450A 30W SINGLE STAGE DESIGN SPECIFICATIONS AC Input Voltage: 120VAC nominal (90VAC - 135VAC) or 230VAC nominal (180VAC - 265VAC) Flyback Output Voltage Maximum: 60V Regulated LED Current: 700mA Bill of Materials *Components are used in both versions unless otherwise noted Reference Designator Description Manufacturer Part Number LM3450A IC PFC CONT 16-TSSOP NSC LM3450AMT LMV431 IC SHUNT REG SOT-23 NSC LMV431AIM5 U1 IC DUAL OP-AMP NSC LM2904 120V CAP CER 0.22F 250V 1210 MURATA GRM32DR72E224KW01L 230V C1a, C1b, C1c, C5a, C5b, C5c CAP CER 68nF 250V 1210 MURATA GRM32QR72E683KW01L C2 CAP MPY 33nF 250VAC X1 RAD EPCOS B32912A3333M C3 CAP CER 47F 6.3V 0805 TAIYO YUDEN JMK212BJ476MG-T 120V CAP MPY 0.22F 400V RAD WIMA MKP10-.22/400/20 230V C4 CAP MPY 62nF 1000V RAD VISHAY BFC238330623 C6 CAP CER 4.7nF 500VAC Y1 RAD EPCOS VY1472M63Y5UQ63V0 C7a CAP ELEC 1mF 63V RAD NICHICON UPW1J102MHD C7b, C8b, C9b, C11, C15 CAP CER 0.1F 50V 1206 MURATA GRM188R71H104KA93D C8a, C9a CAP ELEC 220F 50V RAD NICHICON UHE1H221MPD C10 CAP CER 10nF 25V 0603 MURATA GRM188R71E103KA01D C12, C13, C14, C18, C19 CAP CER 1F 16V 0603 MURATA GRM188R71C105KA12D C16 CAP CER 0.22F 16V 0603 TDK C1608X7R1C224K C17 CAP CER 10F 16V 1206 MURATA GRM31CR71C106KAC7L 120V DIODE ULTRAFAST 200V 1A SMA FAIRCHILD ES1D 230V DIODE FAST 400V 1A DO-214AC FAIRCHILD ES1G D2 DIODE ULTRAFAST 200V 1A SMA FAIRCHILD ES1D D3, D5 DIODE ULTRAFAST 100V 0.2A SOT-23 FAIRCHILD MMBD914 D1a, D1b D4 DIODE DUAL SCHOTTKY 20V 0.5A SOT-23 NXP SEMI PMEG3005CT,215 120V DIODE TVS 150V 600W UNI SMB LITTLEFUSE SMBJ150A 230V DIODE TVS 220V 600W UNI SMB LITTLEFUSE SMBJ220A D7 DIODE ULTRAFAST 600V 1A SMA FAIRCHILD ES1J D8 DIODE ZENER 24V 1.5W SMA MICRO-SEMI SMAJ5934B-TP D9 DIODE SCHOTTKY 20V 3A SMA FAIRCHILD ES2AA-13-F D10 DIODE RECT 600V 0.5A Minidip COMCHIP HD06 D11, D12 DIODE ZENER 10V 500mW SOD-123 FAIRCHILD MMSZ5240B D13 DIODE ZENER 1.8V 500MW SOD-123 ON-SEMI MMSZ4678T1G D17 DIODE ZENER 3.9V 500MW SOD-123 ON-SEMI MMSZ4686T1G D18 DIODE ZENER 18V 500MW SOD-123 ON-SEMI MMSZ5248T1G D19 DIODE SCHOTTKY 30V 200mA SOT-23 FAIRCHILD BAT54 L1 IND LINE FILTER 6mH 0.3A 11M PANASONIC ELF-11M030E L1, L2, L3 IND SHIELD 1mH 1.18A SMT COILCRAFT MSS1278-105KL L4 IND SHIELD 270H 2.34A SMT COILCRAFT MSS1278-274KLB Q1 MOSFET N-CH 800V 3A DPAK ST MICRO STD4NK80ZT4 120V MOSFET N-CH 500V 9A DPAK ST MICRO STD11NM50N 230V MOSFET N-CH 800V 6A DPAK INFINEON SPD06N80C3 Q3, Q4 TRANS NPN 40V 0.6A SOT-23 FAIRCHILD MMBT4401 Q6 TRANS NPN 40V 0.2A SOT-23 FAIRCHILD MMBT3904 D6 Q2 27 www.national.com LM3450 LM3450A Reference Designator Description Manufacturer Part Number R1 R2 120V RES 330 5% 1W 2512 VISHAY CRCW2512330RJNEG 230V RES 510 5% 1W 2512 VISHAY CRCW2512510RJNEG 120V RES 430 5% 1W 2512 VISHAY CRCW2512430RJNEG 230V RES 1.6k 5% 1W 2512 VISHAY CRCW25121K60JNEG 120V RES 402k 1% 0.25W 1206 VISHAY CRCW1206402KFKEA RES 953k 1% 0.25W 1206 VISHAY CRCW1206953KFKEA R4 RES 100 1% 1W 2512 VISHAY WSL2512100RFKEA R5 RES 100k 1% 0.1W 0603 VISHAY CRCW0603100KFKEA R6 RES 6.04k 1% 0.1W 0603 VISHAY CRCW06036K04FKEA R7 RES 499k 1% 0.1W 0603 VISHAY CRCW0603499KFKEA R8, R9 RES 49.9k 1% 0.1W 0603 VISHAY CRCW060349K9FKEA R3 230V R10 R11 RES 20k 1% 0.1W 0603 VISHAY CRCW060320K0FKEA 120V RES 1.00M 1% 0.25W 1206 VISHAY CRCW12061M00FKEA 230V RES 2.00M 1% 0.25W 1206 VISHAY CRCW12062M00FKEA R12 RES 15.0k 1% 0.1W 0603 VISHAY CRCW060315K0FKEA R13 RES 5.11k 1% 0.1W 0603 VISHAY CRCW06035K11FKEA R14a, R14b, R23a, R23b, RES 1.00 1% 0.33W 1206 R23c VISHAY CRCW12061R00FKEA R15a, R15b RES 5.62 1% 0.25W 1206 VISHAY CRCW12065R62FKEA R16 RES 1.00k 1% 0.125W 0805 VISHAY CRCW08051K00FKEA RES 30.1k 1% 0.1W 0603 VISHAY CRCW060330K1FKEA RES 15.0k 1% 0.1W 0603 VISHAY CRCW060315K0FKEA R17 120V 230V R18 RES 105k 1% 0.125W 0805 VISHAY CRCW0805105KFKEA R19 RES 2.49k 1% 0.1W 0603 VISHAY CRCW06035K49FKEA R20 RES 6.04k 1% 0.125W 0805 VISHAY CRCW08056K04FKEA R21 RES 10.0k 1% 0.125W 0805 VISHAY CRCW080510K0FKEA R22 RES 1.4k 1% 0.125W 0805 VISHAY CRCW08051K40FKEA R24, R25 R26 R27, R28 RES 10k 1% 0.1W 0603 VISHAY CRCW060310K0FKEA 120V RES 2.49k 1% 0.125W 0805 VISHAY CRCW08052K49FKEA 230V RES 4.99k 1% 0.125W 0805 VISHAY CRCW08054K99FKEA 120V RES 5 10% 3W WIREWOUND VISHAY PAC300005008FAC000 230V RES 10 10% 3W WIREWOUND VISHAY PAC300001009FAC000 R29, R30 RES 4.99k 1% 0.1W 0603 VISHAY CRCW06034K99FKEA R32 RES 909 1% 0.1W 0603 VISHAY CRCW0603909RFKEA OPTO1, OPTO2 OPTO-ISOLATOR SMD LITE ON CNY17F-3S 120V XFORMER 120V 30W OUTPUT 50V WURTH 750813651 230V XFORMER 230V 30W OUTPUT 50V WURTH 750817651 T1 Thermal Protect www.national.com see Dynamic Hold section 28 LM3450 LM3450A Physical Dimensions inches (millimeters) unless otherwise noted TSSOP-16 Pin Package (MTC) For Ordering, Refer to Ordering Information Table NS Package Number MTC16 29 www.national.com LM3450 LM3450A LED Drivers with Active Power Factor Correction and Phase Dimming Decoder Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated