Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called"TAIYO YUDEN' s official sales channel"). It is only applicable to the products purchased from any of TAIYO YUDEN's official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to"Foreign Exchange and Foreign Trade Control Law"of Japan,"U.S. Export Administration Regulations", and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 12 notice_e-01 MULTILAYER CERAMIC DEVICES (FILTERS / DIPLEXERS / BALUNS) REFLOW FEATURES APPLICATIONS Compact and Low-profile Bluetooth(R) module, Wireless LAN, Digital TV Low loss and high attenuation Stable temperature characteristics ORDERING CODE F I FI 2 Device code Filters for High Frequency 1 2 B Electrode code With Plating Blank space 4 5 Dimensions code mm 325 3.2x2.5 212 2.0x1.25 168 1.6x0.8 105 1.0x0.5 EXTERNAL DIMENSIONS/STANDARD QUANTITY FI 325P Type 3.20.20 1.60.10 2 0 B L C P T D FrequencyMHz Special Code Band Pass Filter Low Pass Filter Balance Filter Diplexer Balun Dual Filter FI 212B Type 5 T 2 example 2450 0620 Spec Code 01 Individual Spec Packaging T Tape & Reel 24002500 470770 FI 212B245025/FI 212B190223 FI 212L Type 0.800.10 2.50.20 1.0max 0.45max. 1.00.10 0.500.15 Unit : mm 0.20.15 0.550.20 FI 212C245033/FI 212C245034 Unit : mm FI 168B/L Type Unit : mm Unit : mm FI 212C249566/FI 212C355068 FI 212C Type 2.000.15 Unit : mm Unit : mm FI 212P Type FI 212C245075 Unit : mm Unit : mm FI 168T Type FI 212P 3960A4 0.40.10 1.60.10 0.800.10 0.5max. 0.500.15 Unit : mm Unit : mm FI 168D Type 1.60.10 FI 168P Type 0.4 Max. 0.100.05 0.500.05 0.800.10 0.300.10 0.500.15 0.65Max 0.300.10 0.30.10 0.20.15 Unit : mm Unit : mm FI 105B/L Type 1.000.05 0.45max. 0.20.15 Unit : mm 0.100.05 Unit : mm Unit : mm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 176 12 chipfilter01_e-01 FI 212C2450XX FI 212C245051 FI 212C249566 FI 212C355068 FI 212P245003 1 GND 2 Common 3 GND Balanced GND Balanced Balanced GND Balanced Balanced GND Balanced GND Common GND FI 212P245003/ FI212P089208/ FI212P085912 GND Common Port GND FI 325P Type FI 212P089213/ FI 212P085909 FI 212P3960A4 GND Low Band Common Port GND GND High Band FI 168T Type FI 168D087018 FI 168P Type Unbalance GND Balanced High Band IN GND Low Band IN Low Band OUT GND High Band OUT GND High Band Common 4 High Band GND GND GND HIGH Band High Band Low Band GND Balanced 5 GND Unbalance Unbalance Unbalance GND GND GND GND GND 6 Low Band DC NC NC or DC Low Band Low Band High Band Common NC 7 8 NC GND NC GND NC GND GND GND Low Band Type Standard Quantitypcs 325P 2000 212B 212L 3000 212C 212P 168B 168L 168T 4000 168D 168P 105B 10000 105L PART NUMBERS Multi-layer band pass filters Applications External dimensions 2.0x1.25x1.0 max. 1.6x0.8x0.5 max. 1.0x0.5x0.4 max. 1.6x0.8x0.5 max. 2.0x1.25x1.0 max. 2.0x1.25x1.0 max. 2.0x1.25x1.0 max. 2.4GHz W-LAN Bluetooth WiMAX UWB PHS Ordering code FI 212B245025/FI 212B245026/FI 212B245027 FI 168B245001 FI 105B245024 FI 168B250065/FI168B24956D FI 212B396001 FI212B448802 FI 212B190223 Notes for ISDB-T Thickness 0.45 mm max. Thickness 0.45 mm max. 2.4GHz W-LAN 1.0x0.5x0.4 max. Bluetooth FI 105L250014 Thickness 0.4 mm max. Other FI 168D087018 Dual band LPF WiMAX External dimensions 2.0x1.25x0.5 max. 1.6x0.8x0.45 max. 1.6x0.8x0.45 max. 1.6x0.8x0.45 max. W-LAN Cellular Ordering code FI 212C245032 FI 212C245033 FI 212C245034 FI 212C245036 FI 212C245051 FI 212C245075 FI 212C249566 FI 212C355068 Notes Conjugated match to CSR BC4 Conjugated match to CSR BC3 Conjugated match to CSR BC4-BGA Conjugated match to CSR BC5 Conjugated match to STLC2500C-D Conjugated match to CSR BC5FM, BC6ROM Thickness 0.5 mm max. Thickness 0.5 mm max. Multi-layer Balun Multi-layer diplexer Applications Applications External dimensions 2.0x1.25x1.0 max. 2.0x1.25x1.0 max. 2.0x1.25x1.0 max. Bluetooth 2.0x1.25x1.0 max. 2.0x1.25x1.0 max. 2.0x1.25x0.7 max. 2.0x1.25x0.5 max. WiMAX 2.0x1.25x0.5 max. External dimensions 2.0x1.25x1.0 max. Ordering code FI 212P245003 FI 168P245010 FI 168P245023 FI 212P089208 FI 212P089213 FI 212P085909 FI 212P085912 1.6x0.8x0.65 max. 2.0x1.25x1.0 max. GPS/ 1.6x0.8x0.65 max. 2.4GHz W-LAN UWB 2.0x1.25x1.0 max. BS 3.2x2.5x1.0 max. Notes Applications External dimensions Ordering code Notes 5GHz 1.6x0.8x0.5 max. FI 168T578717 Thickness 0.5 mm max. BS 1.6x0.8x0.5 max. FI 168T155021 Thickness 0.5 mm max. HIGH FREQUENCY PRODUCTS Ordering code FI 212L062003 FI 168L062005 FI 168L259764 Digital TV WiMedia Band group 1 WiMedia Band group 1 TFC 7 Multi-layer balance filters Multi-layer low pass filters Applications Notes FI 168P157519 FI212P3960A4 FI325P120057 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 212B245025 Pass band frequency 2400-2500MHz 1.4 dB max.25 deg-C Insertion loss at pass band 1.7 dB max.3085 deg-C Ripple at pass band 1.0 dB max. V.S.W.R. at pass band 2.0 max. 30 dB min.824 - 960 MHz 30 dB min.850 MHz 30 dB min.900 MHz 30 dB min.1800 MHz Attenuation 30 dB min.1900 MHz 27 dB min.1710 - 1910 MHz 20 dB min.4800 - 5000 MHz 20 dB min.5000 MHz FI 212B245026 FI 212B245027 Pass band frequency 2400 - 2500 MHz 2.6 dB max.25 deg-C Insertion loss at pass band 2.9 dB max.4085 deg-C Ripple at 1.0 dB max. pass band V.S.W.R. at 2.0 max. pass band 40 dB min.800 - 960 MHz 30 dB min.1710 - 1990 MHz Attenuation 25 dB min.2110 - 2170 MHz 30 dB min.4800 - 5000 MHz 30 dB min.7200 - 7500 MHz Impedance 50 ohm Pass band frequency 2400-2500MHz 1.4 dB max.25 deg-C 1.7 dB max.4085 deg-C Ripple at pass band 1.0 dB max. V.S.W.R. at pass band 2.0 max. 30 dB min.800 - 960 MHz 30 dB min.1710 - 1910 MHz Attenuation 6 dB min.2110 - 2170 MHz 20 dB min.4800 - 5000 MHz Insertion loss at pass band This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfilter01_e-01 12 177 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 168B245001 FI 212B190223 Pass band frequency 2400 - 2500MHz 2.2 dB25deg-C Insertion loss at pass band 2.5 dB3085deg-C Ripple at pass band 1.0 dB max. V.S.W.R. at pass band 2.1 max. 25 dB min.880 - 960MHz 25 dB min.1710 - 1910MHz Attenuation 20 dB min.4800 - 5000MHz 20 dB min.7200 - 7500MHz Impedance 50 ohm Pass band frequency 1884-1930MHz Insertion Loss at 1.7 dB max.25deg-C 1884-1920MHz 2.0 dB max.30-85deg-C Insertion Loss at 1.7 dB max.25deg-C 1920-1930MHz 2.0 dB max.30-85deg-C Ripple at Pass band 1.0 dB max. V.S.W.R. at Pass band 2.0 max. 30 dB min.1420MHz Attenuation 18 dB min.3768-3860MHz Impedance 50 ohm FI 105B245024 FI 212L062003 Pass band frequency 2400-2500MHz 3.0 dB max.25 deg-C Insertion loss at pass band 3.3 dB max.4085 deg-C Ripple at pass band 1.0 dB max. V.S.W.R. at pass band 2.2 max. 25 dB min.880 - 960 MHz 22 dB min.1710 - 1910 MHz Attenuation 20 dB min.4800 - 5000 MHz 20 dB min.7200 - 7500 MHz Pass band frequency 470 - 770 MHz 0.7 dB max.25 deg-C Insertion loss at 470 - 600MHz 0.9 dB max.3085 deg-C 1.5 dB max.25 deg-C Insertion loss at 600 - 710MHz 1.7 dB max.3085 deg-C 3.3 dB max.25 deg-C Insertion loss at 710 - 770MHz 3.7 dB max.3085 deg-C Ripple at 470 - 710 MHz 1.2 dB max. V.S.W.R. at 470 - 710 MHz 2.5 max. 15 dB min.830 - 840 MHz 25 deg-C 11 dB min.830 - 840 MHz 3085 deg-C 15 dB min.888 - 925 MHz Attenuation 15 dB min.940 - 960 MHz 7 dB min.1429 - 1453 MHz 8 dB min.1920 - 1980 MHz 8 dB min.2400 - 2500 MHz Impedance 50 ohm FI 168B250065 Pass band frequency 2300 - 2700 MHz 2.4 dB max.25 deg-C Insertion loss at 2300 - 2500 MHz 2.6 dB max.3085 deg-C 2.3 dB max.25 deg-C Insertion loss at 2500 - 2700 MHz 2.5 dB max.3085 deg-C Ripple at 1.4 dB max. 2300 - 2500 MHz Ripple at 1.3 dB max. 2500 - 2700 MHz V.S.W.R. at 2.4 max. 2300 - 2500 MHz V.S.W.R. at 1.3 max. 2500 - 2700 MHz 15 dB min.1500 - 2000 MHz Attenuation 10 dB min.4600 - 8000 MHz Impedance 50 ohm FI 168L062005 Pass band frequency 470 - 770 MHz 1.2 dB max.25 deg-C Insertion loss at 470-600MHz 1.3 dB max.3085 deg-C 2.2 dB max.25 deg-C Insertion loss at 600-710MHz 2.4 dB max.3085 deg-C 4.0 dB max.25 deg-C Insertion loss at 710-770MHz 4.4 dB max.3085 deg-C Ripple at 470 - 710 MHz 1.4 dB max. 2.0 max.470 - 710 MHz V.S.W.R. 2.5 max.710 - 770 MHz 25 dB min.888 - 925 MHz 25 deg-C 21 dB min.888 - 925 MHz 3085 deg-C Attenuation 25 dB min.940 - 960 MHz 27 dB min.1429 - 1453 MHz 26 dB min.1920 - 1980 MHz 26 dB min.2400 - 2500 MHz Impedance 50 ohm FI 168B24956D Pass band frequency 2300 - 2690MHz 2.3 dB25deg-C 2.6 dB-30+85deg-C Ripple at pass 0.8 dB max. band V.S.W.R. at pass 2.1 max. band 15 dB min. (DC-1620MHz) Attenuation 23 dB min. (3490-4000MHz) 25 dB min. (4490-8000MHz) 50 ohm Impedance Insertion loss at pass band FI 168L259764 FI 212B396001 Pass band frequency 3168 - 4752 MHz 2.7 dB max.25 deg-C Insertion loss at pass band 3.0 dB max.3085 deg-C Ripple at pass band 2.0 dB max. V.S.W.R. at pass band 2.5 max. 33 dB min.900MHz 25 dB min.1500MHz Attenuation 22 dB min.1900MHz 13 dB min.2500MHz 10dB min.5150MHz Impedance 50 ohm Pass band frequency Insertion loss at 470-770MHz Insertion loss at 2300-2700MHz Ripple at 470 - 770 MHz Ripple at 2300 - 2700 MHz V.S.W.R.at 470 - 770MHz V.S.W.R.at 2300 - 2700MHz Attenuation Impedance FI 212B448802 Pass band frequency 4224 - 4752 MHz 2.4 dB max.25 deg-C Insertion loss at 4224 - 4488 MHz 2.7 dB max.3085 deg-C 2.5 dB max.25 deg-C Insertion loss at 4488 - 4752 MHz 2.8 dB max.3085 deg-C Ripple at pass band 1.5 dB max. V.S.W.R. at pass band 2.2 max. 40 dB min.2400-2500MHz Attenuation 25 dB min.3300-3600MHz 10 dB min.5158-5850MHz Impedance 50 ohm 470 - 770 MHz 2300 - 2700 MHz 0.5 dB max.25 deg-C 0.6 dB max.3085 deg-C 0.5 dB max.25 deg-C 0.6 dB max.3085 deg-C 0.3 dB max. 0.3 dB max. 2.0 max. 2.0 max. 20 dB min.4600 - 5400 MHz 20 dB min.6900 - 8100 MHz 50 ohm FI 105L250014 Pass band frequency 2400-2500MHz 0.45 dB max.25 deg-C Insertion loss at 2400 - 2500 MHz 0.55 dB max.4085 deg-C V.S.W.R. at 1.7 max. 2400 - 2500 MHz 21 dB min.4800 - 5000 MHz Attenuation 21 dB min.7200 - 7500 MHz Impedance 50 ohm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 178 12 chipfilter01_e-01 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 168D087018 -20 -30 S11 S21 -40 -50 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 0 -10 -20 -30 S11 S21 -40 -50 0.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 FI 212C245034 -10 Low band Pass band frequency 824 - 915 MHz Insertion loss at 0.6 dB max. -20 to +85 Deg.C 824 - 915 MHz V.S.W.R. 1.5 max. at 824 - 915 MHz 25 dB min.1648-1830MHz Attenuation 25 dB min.2472-2745MHz Impedance 50 ohm High band Pass band frequency 1710 - 1910 MHz Insertion loss at 0.6 dB max. -20 to +85 Deg.C 1710 - 1910 MHz V.S.W.R. 1.5 max. at 824 - 915 MHz 25 dB min.3420-3820MHz Attenuation 25 dB min.5130-5730MHz Impedance 50 ohm Isolation 27 dB min.824-915MHz In to In/Out to Out 30 dB min.1710-1910MHz 30 dB min.824-915MHz In to Out 30 dB min.1710-1910MHz Pass band frequency 2400-2500MHz 2.7 dB max.25 deg-C 3.0 dB max.3085 deg-C Ripple at pass band 1.0 dB max. Amp. balance at 2.0 dB Max. Passband Phase Balance at 180 / 10 deg Passband Unbalanced Port 2.0 max. V.S.W.R at Passband Balanced Port 2.0 max. V.S.W.R at Passband 25 dB min.880 - 960 MHz 15 dB min.1710 - 1990 MHz Attenuation 12 dB min.1990 - 2170 MHz 15 dB min.4800 - 5000 MHz Unbalanced Port 50 ohm Impedance Insertion loss at pass band 0 Balanced Port Impedance Conjugated to CSR BC4-BGA, BC5-BGA FI 212C245036 FI 212C245032 Pass band frequency 2400-2500MHz 3.7 dB25deg-C 4.0 dB3085deg-C Ripple at pass band 1.0 dB max. Unbalanced port 2.0 max. V.S.W.R. at pass band Insertion loss at pass band Balanced port V.S.W.R. 2.0 max. at pass band Amplitude Imbalance 2.0 dB max. at pass band Phase Imbalance 180 / 10 deg at pass band 35 dB min.880-960MHz 20 dB min.1710-1990MHz Attenuation 20 dB min.1990-2170MHz 20 dB min.4800-5000MHz Unbalanced Port 50 ohm Impedance Balanced Port Conjugated match to CSR BC4 Impedance HIGH FREQUENCY PRODUCTS Pass band frequency 2400-2500MHz 3.7 dB25deg-C 4.0 dB3085deg-C Ripple at pass band 1.0 dB max. Unbalanced port 2.0 max. V.S.W.R. at pass band Balanced port V.S.W.R. 2.0 max. at pass band Amplitude Imbalance 2.0 dB max. at pass band Phase Imbalance 180 / 10 deg at pass band 35 dB min.880-960MHz 20 dB min.1710-1990MHz Attenuation 15 dB min.1990-2170MHz 20 dB min.4800-5000MHz Unbalanced Port Impedance 50 ohm Balanced Port Conjugated match to CSR BC5 Impedance Insertion loss at pass band FI 212C245033 Pass band frequency 2400-2500MHz Insertion loss at pass 2.7 dB25deg-C band 3.0 dB3085deg-C Ripple at pass band 1.0 dB max. Unbalanced port 2.0 max. V.S.W.R. at pass band Balanced port V.S.W.R. 2.0 max. at pass band Amplitude Imbalance 2.0 dB max. at pass band Phase Imbalance 180 / 10 deg at pass band 25 dB min.880-960MHz 15 dB min.1710-1990MHz Attenuation 15 dB min.1990-2170MHz 15 dB min.4800-5000MHz Unbalanced Port Impedance 50 ohm Balanced Port Conjugated match to CSR BC3 Impedance This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfilter01_e-01 12 179 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 212C245051 FI 212C355068 Pass band frequency 2400-2500MHz 3.7 dB25deg-C Insertion loss at pass band 4.0 dB3085deg-C Ripple at pass band 1.0 dB max. Unbalanced port 2.0 max. V.S.W.R. at pass band Balanced port V.S.W.R. 2.0 max. at pass band Amplitude Imbalance 2.0 dB max. at pass band Phase Imbalance 180 / 10 deg at pass band 40 dB min.824 - 960MHz 12 dB min.1570-1580MHz 27 dB min.1710-1785MHz Attenuation 25 dB min.1805-1880MHz 23 dB min.1880-1910MHz 20 dB min.4800-5000MHz Unbalanced Port 50 ohm Impedance Balanced Port Conjugated match to STLC2500C-D Impedance Pass band frequency 3300-3800MHz 2.5 dB25 deg-C 2.8 dB-30+85 deg-C Ripple at pass 1.0 dB max. band Insertion loss at pass band 2.0 3.0 4.0 Attenuation Impedance 2.0 dB max. 180 / 12 deg 40 dB min.1710-1990MHz 40 dB min.2110-2170MHz 35 dB min.2400-2500MHz 15 dB min.4900-5850MHz 50:100 Pass band frequency 2400-2500MHz 0.5 dB max.25 deg-C Insertion loss at 2400-2500MHz 0.7 dB max.3085 deg-C Pass band frequency 2400-2500MHz 3.7 dB25deg-C 4.0 dB3085deg-C Ripple at pass band 1.0 dB max. Unbalanced port 2.2 max. V.S.W.R. at pass band Balanced port V.S.W.R. 2.2 max. at pass band Amplitude Imbalance 2.0 dB max. at pass band Phase Imbalance 180 / 10 deg at pass band 40 dB min.880-960MHz 18 dB min.1710-1990MHz Attenuation 12 dB min.1990-2170MHz 30 dB min.4800-5000MHz Unbalanced Port 50 ohm Impedance Balanced Port Impedance 2.3 max. Low band Insertion loss at pass band 2.3 max. FI 212P245003 FI 212C245075 Unbalanced port V.S.W.R. at pass band Balanced port V.S.W.R. at pass band Amplitude imbalance at pass band Phase imbalance at pass band V.S.W.R. Attenuation 20 dB min.5150-5350MHz 14 dB min.5470-5825MHz High band Pass band frequency 1 4900-5150MHz Pass band frequency 2 5150-5350MHz Pass band frequency 3 5470-5825MHz Conjugated match to CSR BC5FM.BC6ROM 0.7 dB max.25 deg-C Insertion loss at pass band 1 0.9 dB max.3085 deg-C Insertion loss at pass band 2 0.8 dB max.3085 deg-C Insertion loss at pass band 3 1.0 dB max.3085 deg-C V.S.W.R. Attenuation FI 212C249566 Pass band frequency 2300-2690MHz 2.9 dB max.25 deg-C Insertion loss at 2300-2495MHz 3.2 dB max.3085 deg-C Ripple at 2300-2495MHz 1.2 dB max. Unbalanced port V.S.W.R. 2.3 max. at 2300-2495MHz Balanced port V.S.W.R. 2.3 max. at 2300-2495MHz Amplitude Imbalance 2.0 dB max. at 2300-2495MHz Phase Imbalance 180 / 12 deg at 2300-2495MHz 2.3 dB max.25 deg-C Insertion loss at 2495-2690MHz 2.6 dB max.3085 deg-C Ripple at 2495-2690MHz 1.0 dB max. Unbalanced port V.S.W.R. 2.3 max. at 2495-2690MHz Balanced port V.S.W.R. 2.3 max. at 2495-2690MHz Amplitude Imbalance 2.0 dB max. at 2495-2690MHz Phase Imbalance 180 / 12 deg at 2495-2690MHz 40 dB Min.824-960MHz Attenuation 15 dB Min.1710-1990MHz 20 dB Min.4900-5850MHz Impedance 50 : 100 2.0 max. 14 dB min.4900-5150MHz 0.6 dB max.25 deg-C 0.9 dB max.25 deg-C 2.0 max.band-1.-2 2.5 max.band-2 20 dB min.2400-2500MHz FI 168P245010 Low band 0 Pass band frequency 2400-2500MHz -10 -20 0.40 dB max.25 deg-C Insertion loss at 2400-2500MHz 0.50 dB max.3085 deg-C -30 V.S.W.R. 2.0 max. at 2400 - 2500 MHz -40 Attenuation 0 2 4 6 8 10 12 20 dB min.4900-5580MHz 15 dB min.5850-8500MHz Impedance High band 50 ohm Pass band frequency 4900 - 5850 MHz 0.60 dB max.25 deg-C Insertion loss at 4900 - 5850 MHz 0.70 dB max.4085 deg-C V.S.W.R. at 4900 - 5850 MHz 2.0 max. Attenuation 20 min.2400-2500MHz Impedance 50 ohm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 180 12 chipfilter01_e-01 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 168P245023 FI 212P085909 Low band 0 -10 -20 0.60 dB max.25 deg-C Insertion loss at 2400-2500MHz 0.70 dB max.3085 deg-C -30 V.S.W.R. 2.0max. at 2400 - 2500 MHz -40 Attenuation 0 2 4 6 8 10 12 Low band 0 Pass band frequency 2400-2500MHz -30 20 dB min.7200-7500MHz -60 0.5 Pass band frequency 4900 - 5950 MHz V.S.W.R. at 698 - 960 MHz -40 20 dB min.4800-6000MHz 50 ohm Insertion loss at 698 - 960 MHz -20 -50 Impedance High band Pass band frequency 698-960 MHz -10 0.70 dB max.+25 deg-.C 0.75 dB max.-30+85 deg-.C 1.6 max. 19dB min.1558-1570MHz 1.0 1.5 2.0 2.5 Attenuation 20dB min.1570-1580MHz 19dB min.1580-1610MHz Impedance High band 50 ohm 0.80 dB max.25 deg-C Insertion loss at 4900 - 5850 MHz 0.95 dB max.4085 deg-C Pass band frequency 1 1558-1570MHz V.S.W.R. at 4900 - 5850 MHz Pass band frequency 3 1580-1610MHz Pass band frequency 2 1570-1580MHz 2.0max. 0.75 dB max.+25 deg-.C Insertion loss at 1558 - 1570 MHz 0.85 dB max.-30+85 deg-.C 20 dB min.1800-2500MHz Attenuation 20 dB min.9800-11900MHz *Referece Impedance 50 ohm 0.70 dB max.+25 deg-.C Insertion loss at 1570 - 1580 MHz 0.80 dB max.-30+85 deg-.C 0.70 dB max.+25 deg-.C Insertion loss at 1580 - 1610 MHz 0.80 dB max.-30+85 deg-.C FI 212P089208 Pass band frequency 698 - 960 MHz 0.27 dB max.25 Deg.C Insertion loss at 698 - 960 MHz 0.32 dB max.40 to 85 Deg.C V.S.W.R. at 698 - 960 MHz 2.0 max. Attenuation 13dB min. (1710-2170MHz) Impedance 50 ohm Attenuation Insertion loss at 1710 - 2170 MHz 0.55 dB max.40 to 85 Deg.C 0.45 dB max. +25 Deg.C -10 Attenuation 19dB min.698-960MHz -20 Impedance 50 ohm -30 Pass band frequency 698-960 MHz Insertion loss at 698 - 960 MHz V.S.W.R. at 698 - 960 MHz -40 -60 0.5 0.70 dB max.+25 deg-.C 0.75 dB max.-30+85 deg-.C 1.6 max. 19dB min.1558-1570MHz -50 Pass band frequency 698 - 960 MHz 50 ohm Low band 0 2.0 max. Low band 35dB min.698-824MHz FI 212P085912 V.S.W.R. at 698 - 960 MHz FI 212P089213 1.6 max. 25dB min.894-960MHz Impedance 1710 - 2170 MHz 1.6 max. 42dB min.824-894MHz High band Pass band frequency 1.6 max. 1.0 1.5 2.0 2.5 Attenuation 20dB min.1570-1580MHz 19dB min.1580-1610MHz 0.27 dB max.25 Deg.C Insertion loss at 698 - 960 MHz 0.32 dB max.40 to 85 Deg.C Impedance High band V.S.W.R. at 698 - 960 MHz 2.0 max. Pass band frequency 1 1558-1570MHz Attenuation 13dB min. (1710-2170MHz) Impedance 50 ohm Pass band frequency 1710 - 2170 MHz 0.45 dB max. 25 Deg.C Pass band frequency 3 1580-1610MHz 0.75 dB max.+25 deg-.C Insertion loss at 1558 - 1570 MHz 0.85 dB max.-30+85 deg-.C 0.70 dB max.+25 deg-.C Insertion loss at 1570 - 1580 MHz 0.80 dB max.-30+85 deg-.C 0.55 dB max.40 to 85 Deg.C V.S.W.R. at 698 - 960 MHz 2.0 max. Attenuation 19dB min.698-960MHz Impedance 50 ohm 50 ohm Pass band frequency 2 1570-1580MHz High band Insertion loss at 1710 - 2170 MHz HIGH FREQUENCY PRODUCTS V.S.W.R. at 1558 - 1570 MHz V.S.W.R. at 1570 - 1580 MHz V.S.W.R. at 1580 - 1610 MHz Low band 0.70 dB max.+25 deg-.C Insertion loss at 1580 - 1610 MHz 0.80 dB max.-30+85 deg-.C V.S.W.R. at 1558 - 1570 MHz V.S.W.R. at 1570 - 1580 MHz V.S.W.R. at 1580 - 1610 MHz 1.6 max. 1.6 max. 1.6 max. 35dB min.698-824MHz Attenuation 42dB min.824-894MHz 25dB min.894-960MHz Impedance 50 ohm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfilter01_e-01 12 181 ELECTRICAL CHARACTERISTICSTYPICAL CHARACTERISTICS FI 168P157519 FI 168T5787717 Low band -40 -50 0.0 1.0 2.0 3.0 0.50 dB max.+25 deg-.C 0.60 dB max.-40+85 deg-.C V.S.W.R. at 824 - 960 MHz V.S.W.R. at 1558 - 1585 MHz V.S.W.R. at 1585 - 1610 MHz 2.0 max. 2.0 max. 13dB min.2400-2500MHz Impedance 50 ohm 2.0 max. Attenuation 0.40 dB max.+25 deg-.C Insertion loss at 1558 - 1585 MHz 0.50 dB max.-40+85 deg-.C 0.45 dB max.+25 deg-.C Insertion loss at 1585 - 1610 MHz 0.55 dB max.-40+85 deg-.C Impedance 2.0 max. 20dB min.1585-1610MHz 1.2 dB max.+25 deg-.C -20 Insertion loss at 3168 - 4782 MHz 1.5 dB max.-40+85 deg-.C -30 V.S.W.R. 2.2 max. at 3168 - 4782 MHz 0 2 4 6 8 10 12 Attenuation 18dB min.6336-9504MHz Impedance High band 50 ohm Pass band frequency 6336-9504MHz Low band Pass band frequency 900-2200MHz 2.0 dB max.25 deg-C 2.3 dB max.-30+85 deg-C V.S.W.R. at pass band 2.3 max. Phase balance 180 / 20 deg at pass band Amplitude Imbalance /2 dB max. at pass band Impedance 50 : 75 Insertion loss at pass band Pass band frequency 3168-4782MHz -40 50 ohm -10 23dB min.1558-1585MHz FI 212P3960A4 0 FI 168T155021 2400 - 2500 MHz 0.60 dB max.+25 deg-.C 0.70 dB max. -40+85 deg-.C 12dB min.824-960MHz Attenuation Pass band frequency 5725-5850MHz 1.0 dB max.25 deg-C 1.2 dB max.-30~+85 deg-C V.S.W.R. at pass band 2.0 max. Phase balance 180 / 10 deg at pass band Amplitude Imbalance 1.0 dB max. at pass band Impedance 50 : 100 Insertion loss at pass band High Band Pass band frequency Insertion loss at 2400 - 2500 MHz V.S.W.R. at 2400 - 2500 MHz Insertion loss at 824 - 960 MHz -30 Pass band frequency 2 1585-1610MHz Pass band frequency 1 1558-1585MHz -20 -10 Pass band frequency 0 824-960MHz 0 1.2 dB max.+25 deg-.C Insertion loss at 6336 - 9504 MHz 1.5 dB max.-40+85 deg-.C V.S.W.R. at 6336 - 9504 MHz 2.2 max. Attenuation 13dB min.3168-4782MHz Impedance 50 ohm FI 325P120057 Low band 0 -10 Pass band frequency 900 - 1450 MHz -20 Insertion loss at 900 - 1450 MHz 4.00 dB max.+25 deg-.C Ripple at 900 - 1450 MHz 3.0 dB max.+25 deg-.C -30 -40 -50 -60 -70 0 1 2 3 V.S.W.R. at 900 - 1450 MHz 4.40 dB max.-40+85 deg-.C 3.4 dB max.-40+85 deg-.C 2.2 max. 44dB min.1650-2200MHz +25 deg-.C Attenuation 40dB min.1650-2200MHz -40+85 deg-.C 45dB min.1650MHz +25 deg-.C 41dB min.1650MHz -40+85 deg.-C Impedance 50 ohm High Band Pass band frequency 1650 - 2200 MHz 4.00 dB max.+25 deg-.C Insertion loss at 1650 - 2200 MHz 4.40 dB max.-40+85 eg-.C 3.0 dB max.+25 deg-.C Ripple at 1650 - 2200 MHz 3.2 dB max. -40 to +85 Deg.C V.S.W.R. 2.25 max. at 1650 - 2200 MHz 44dB min.900-1450MHz +25 deg-.C Attenuation 40dB min.900-1450MHz -40+85 deg-.C 45dB min.1450MHz +25 deg-.C 41dB min.1450MHz -40+85 deg-.C Impedance 50 ohm This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 182 12 chipfilter01_e-01 HIGH FREQUENCY PRODUCTS This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfilter01_e-01 12 183 PACKAGING Minimum Quantity Type 325P 212B 212L 212C 212P 168B 168L 168T 168D 168P 105B 105L Embossed Tape [pcs] 2000 3000 Tape Material B F Tape Thickness max. K T 2.750.2 3.550.2 4.00.1 1.35 0.3 0.1080.008 0.140.008 0.1570.004 0.053 0.012 212B 1.50.25 2.30.2 4.00.1 1.6 0.3 0.0590.0080.0910.0080.1570.004 0.063 0.012 212L 1.550.2 2.30.2 4.00.1 0.65 0.65 0.0610.0080.0910.0080.1570.004 0.026 0.026 212C-0.5 10000 A Insertion Pitch 325P 212C 4000 Chip cavity Type EIA 1.550.2 2.30.2 4.00.1 1.6 0.3 0.0610.0080.0910.008 0.1570.004 0.063 0.012 212C-0.7 1.550.2 2.30.2 4.00.1 1.3 0.3 0.0610.0080.0910.0080.1570.004 0.051 0.012 212P 1.550.2 2.30.2 4.00.1 1.6 0.3 0.0610.0080.0910.0080.1570.004 0.063 0.012 168B 1.000.05 1.800.05 4.00.1 0.55 0.55 0.0390.0020.0710.0020.1570.004 0.022 0.022 168L 1.000.05 1.800.05 4.00.1 0.55 0.55 0.0390.0020.0710.0020.1570.004 0.022 0.022 168T 1.000.05 1.800.05 4.00.1 0.55 0.55 0.0390.0020.0710.0020.1570.004 0.022 0.022 168D 1.000.05 1.800.05 4.00.1 0.55 0.55 0.0390.0020.0710.0020.1570.004 0.022 0.022 168P 0.950.05 1.800.05 4.00.1 0.80 0.80 0.0370.0020.0710.0020.1570.004 0.031 0.031 105B 0.620.03 1.120.03 2.00.05 0.45 0.45 0.0240.0010.0440.0010.0790.002 0.018 0.018 105L 0.620.03 1.120.03 2.00.05 0.45 0.45 0.0240.0010.0440.0010.0790.002 0.018 0.018 Unit : mm (inch) Leader and Blank Portion 160mm or more 100mm or more Taped package Type (EIA) 325P 212B 212L 212C 212P 212C-0.5 212C-0.7 168B 168L 168T 168D 168P 105B 105L Thickness mm (inch) 0.90 typ. 0.035 0.90 typ. 0.035 0.45 typ. 0.018 0.90 typ. 0.035 0.90 typ. 0.035 0.45 typ. 0.018 0.60 typ. 0.024 0.45 typ. 0.018 0.45 typ. 0.018 0.45 typ. 0.018 0.45 typ. 0.018 0.60 typ. 0.024 0.30 typ. 0.0118 0.30 typ. 0.0118 Standard Quantity [pcs] 2000 Reel size 3000 4000 10000 Taping Dimensions Unit : mminch Embossed tape 0.315 inches wide (325P Type, 212B Type, 212C Type, 212C-0.7 Type Paper tape 0.315 inches wide (212L Type, 212C-0.5 Type, 168B Type, 168L Type, 168 Type, 168T Type, 168DType, 105B Type, 105L Type Top Tape Strength The top tape requires a peel-off force of 0.10.7N in the direction of the arrow as illustrated below. Unit : mminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfil_reli-PRP1 12 chipfil_reli_e-01 RELIABILITY DATA 1. Operating Temperature Range Specified Value 3085 2. Storage Temperature Range Specified Value Test Methods and Remarks Note : 20 to +40 in taped packaging 3085 3. Resistance to Flexure of Substrate Specified Value Test Methods and Remarks Warp : 2mm Testing board : Glass epoxy-resin substrate Thickness : 0.8mm No mechanical damage. 4. Adhesion of Electrode Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Specified Value Test Methods and Remarks Applied force : 5N Duration : 10 sec. 5. Solderability Specified Value Test Methods and Remarks Solder temperature : 2305 Duration : 41 sec. 75% or more of immersed surface of terminal electrode shall be covered with fresh solder. Preconditioning : Immersion into flux. Immersion and Removal speed : 25mm/sec. 6. Resistance to Solder Heat Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Specified Value Test Methods and Remarks : 150 for 2 min. Preheating Solder temperature : 2605 Duration : 50.5 sec. Preconditioning : Immersion into flux. Immersion and Removal speed : 25mm/sec. Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 7. Thermal Shock Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Specified Value Test Methods and Remarks According to JIS C 0025. Conditions for 1 cycle Step 1 2 3 4 Temperature () 403 Room Temperature 852 Room Temperature Duration (min) 303 Within 3 303 Within 3 Number of cycles : 100 Mounting method : Soldering onto PC board. Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 8. Humidity (steady state) Specified Value Test Methods and Remarks Temperature : 402 Humidity : 9095%RH Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Duration : 96 hrs Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 9. High temperature life test Specified Value Test Methods and Remarks Temperature : 852 Duration : 96 hrs Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. 10. Low temperature life test Specified Value Test Methods and Remarks Temperature : 402 Duration : 96 hrs Characteristics : shall satisfy the electrical characteristics. Appearance : No significant abnormality. Recovery : 2 to 3 hrs of recovery under the standard condition after the removal from test chamber. Note on standard condition: "standard condition" referred to herein is defined as follows : 5 to 35 of temperature, 45 to 85% relative humidity and 86 to 106kPa of air pressure. When there are questions concerning measurement result : In order to provide correlation data, the test shall be conducted under condition of 202 of temperature, 60 to 70% relative humidity and 86 to 106kPa of air pressure. Unless otherwise specified, all the tests are conducted under the "standard condition". This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfil_reli-PRP2 12 chipfil_reli_e-01 PRECAUTIONS 1. PCB Design Land pattern design Land pattern dimension examples FI212B Type FI212B245025/FI212B190223 FI212L Type 1.50 FI325P Type 1.50 1.0 0.8 Unit : mm Unit : mm FI168T/D Type FI168P Type FI168B/L Type 0.25 0.45 0.6 0.3 0.45 0.55 Technical considerations FI212C Type 0.6 0.50 Unit : mm Unit : mm 0.30 0.25 0.25 1.1 Unit : mm FI212P Type Unit : mm Unit : mm FI212 P3960A4 Unit : mm FI105B/L Type 0.7 0.3 0.05 0.2 0.45 0.3 0.45 0.2 Unit : mm Unit : mm Unit : mm 2. Soldering Conditions for Reflow soldering (for reference) Reflow Profile Components should be preheated to within 100 to 130 from soldering temperature. Assured to be reflow soldering for 2 times. Technical considerations Note : The above profiles are the maximum allowable soldering condition, therefore these profiles are not always recommended. 3. Storage conditions Storage 1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control temperature and humidity in the storage area. Humidity should especially be kept as low as possible. Recommended conditions Ambient temperature : 2040 Precautions Humidity : Below 70%RH The ambient temperature must be kept below 30. Even under ideal storage conditions, the solderbility of electrodes decreases gradually, so filters should be mounted within 6 months from the time of delivery. The packaging material should be kept where no chlorine or sulfur exists in the air. Storage Technical 1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerand deterioration of taping/ packaging materials may take place. For this reason, components should be used within 6 months from the time of delivery. If ations exceeding the above period, please check the solderability before using the filter. Please contact of our offices for further details of specifications. All of the standard values listed here are subject to change without notice. Therefore,please check the specifications carefully before use. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. chipfil_reli-PRP3 12 chipfil_reli_e-01