ADQM16009 - Panasonic - Datasheet.Directory

http://www.mew.co.jp/ac/e/

*High capacity of 60 A achieved, twice the previous model.

Matsushita Electric Works, Ltd.

DQ-M Relay

ASCT1B352E ’08.7

New

Polarized Power Relays

Miniature 60A* Polarized Power Relay

DQ-M (ADQM)

ORDERING INFORMATION

TYPES

Standard packing: Tube: 20 pcs.; Case: 200 pcs.

RATING

1. Coil data

1) 1 coil latching

60A POWER LATCHING

RELAY

DQ-M RELAYS (ADQM)

Contact

arrangement

Nominal coil

voltage

Part No.

1 coil latching 2 coil latching

1 Form A

4.5V DC ADQM1604H ADQM2604H

6V DC ADQM16006 ADQM26006

9V DC ADQM16009 ADQM26009

12V DC ADQM16012 ADQM26012

24V DC ADQM16024 ADQM26024

Nominal coil

voltage

Set voltage

(at 20°C 68°F)

Reset voltage

(at 20°C 68°F)

Nominal operating

current

[±10%] (at 20°C 68°F)

Coil resistance

[±10%] (at 20°C 68°F)

Nominal operating

power

Max. allowable voltage

(at 20°C 68°F)

4.5V DC

80%V or less of

nominal voltage

(Initial)

80%V or less of

nominal voltage

(Initial)

111.1mA 40.5Ω

500mW 130%V of

nominal voltage

6V DC 83.3mA 72Ω

9V DC 55.6mA 162Ω

12V DC 41.7mA 288Ω

24V DC 20.8mA 1,152Ω

RoHS Directive compatibility information

http://www.mew.co.jp/ac/e/environment/

FEATURES

1. Miniature and high capacity

Miniature relay capable of high 60 A

capacity control.

Size: 29.0(L)×38.0(W)×17.3(H) mm

1.142(L)×1.496(W)×.681(H) inch

Nominal switching capacity:

60A 250V AC

2. Latching type

Latching type contributes to device

energy efﬁciency.

Nominal operating power

• 500mW (1 coil latching)

• 1W (2 coil latching)

3. High insulation

Between contact and coil

Breakdown voltage: 4,000 V AC

Surge breakdown voltage: 10,000 V

4. Cd-free, Pb-free

5. Flux-Resistant type

TYPICAL APPLICATIONS

1. Remote control of electric power

meters

2. Time switches

DQ-M relays

Operating function

1: 1 coil latching (1 Form A)

2: 2 coil latching (1 Form A)

Coil voltage (DC)

4H: 4.5 V, 06: 6 V, 09: 9 V, 12: 12 V, 24: 24 V

ADQM 6 0

Contact capacity

6: 60 A

Terminal shape

Nil: M4 securing screw

Contact characteristics

0: Standard contact

DQ-M (ADQM)

2) 2 coil latching

2. Speciﬁcations

Notes: *1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the

actual load.

*2 Wave is standard shock voltage of ±1.2×50µs according to JEC-212-1981

*3 The upper operation ambient temperature limit is the maximum temperature that can satisfy the coil temperature rise value. Refer to [6] AMBIENT ENVIRONMENT

in GENERAL APPLICATION GUIDELINES.

DIMENSIONS (Unit: mm inch)

Nominal coil

voltage

Set voltage

(at 20°C 68°F)

Reset voltage

(at 20°C 68°F)

Nominal operating

current

[±10%] (at 20°C 68°F)

Coil resistance

[±10%] (at 20°C 68°F)

Nominal operating

power

Max. allowable voltage

(at 20°C 68°F)

4.5V DC

80%V or less of

nominal voltage

(Initial)

80%V or less of

nominal voltage

(Initial)

221.7mA 20.3Ω

1,000mW 130%V of

nominal voltage

6V DC 166.7mA 36Ω

9V DC 111.1mA 81Ω

12V DC 83.3mA 144Ω

24V DC 41.7mA 576Ω

Characteristics Item Speciﬁcations

Contact

Arrangement 1 Form A

Contact resistance (Initial) Max. 30 mΩ (By voltage drop 6 V DC 1A)

Contact material Ag alloy (Cadmium free)

Rating

Nominal switching capacity (resistive load) 60 A 250V AC

Max. switching power (resistive load) 15,000 V A

Max. switching voltage 250V AC

Max. switching current 60 A

Nominal operating power 500mW (1 coil latching), 1,000mW (2 coil latching)

Min. switching capacity (Reference value)*1100mA 5 V DC

Electrical

characteristics

Insulation resistance (Initial) Min. 1,000MΩ (at 500V DC)

Measurement at same location as “Initial breakdown voltage” section.

Breakdown voltage

(Initial)

Between open contacts 1,500 Vrms for 1min. (Detection current: 10mA.)

Between contact and coil 4,000 Vrms for 1min. (Detection current: 10mA.)

Surge breakdown

voltage*2Between contact and coil Min. 10,000 V (initial)

Temperature rise (at 20°C 68°F) Max. 50°C (By resistive method, max. switching current) (Coil; de-energized)

Set time (at 20°C 68°F) Max. 20 ms (Nominal voltage applied to the coil, excluding contact bounce time.)

Reset time (at 20°C 68°F) Max. 20 ms (Nominal voltage applied to the coil, excluding contact bounce time.)

Mechanical

characteristics

Shock resistance Functional Min. 200 m/s2 (Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)

Destructive Min. 1,000 m/s2 (Half-wave pulse of sine wave: 6 ms.)

Vibration resistance Functional 10 to 55 Hz at double amplitude of 1.5 mm (Detection time: 10µs.)

Destructive 10 to 55 Hz at double amplitude of 2.0 mm

Expected life

Mechanical Min. 106 (at 180 cpm)

Electrical 60A 250V AC Min. 103 (resistive load, operating frequency: 15s ON, 45s OFF)

50A 250V AC Min. 104 (resistive load, operating frequency: 15s ON, 45s OFF)

Conditions Conditions for operation, transport and storage*3Ambient temperature: –40°C to +70°C –40°F to +158°F

Humidity: 5 to 75% R.H. (Not freezing and condensing at low temperature)

Max. operating speed 1 cpm (at rated load)

Unit weight Approx. 35 g 1.23 oz

Note 1)

These are dummy terminals for the

strength reinforcement for the M4 screw

terminal connection. Fix or solder these to

the PC board in case setting M4 screw.

However, do not use the dummy terminals

as wiring to the PC board. In case wiring

of the dummy terminals, the conductor

destruction may occur due to the high

current.

Note 2)

No 3rd terminal on 1 coil latching type.

External dimensions

Note 1)

2 coil latching

type only

This differs with

the part No.

0.8

.031

0.8

.031

7.62

.300

3.6

.142

0.8

.031

0.8

.031

2-4.3 dia.

2-.169 dia.

2-8.7

2-.343

MADE IN JAPAN

ADQM26012

Lot. No. 1.5

.059 (8.9)

(.350)

(2.0)

(.079)

5.08

.200

5.08

.200

1.8

.071

0.4

.016

1.5

.059

0.4

.016

5.8

.228

25.4

1.000

29.5

1.161

40.4

1.591

19.42

.765

20.56

.809

2-9.9

2-.390

29.0

1.142

38.0

1.496

44.0

1.732

34.5

1.358

40.4

1.591

22.86

.700

3.7

.146

17.3

.681

9.25

.364

5.08

.200

0.3

.012

General tolerance: ±0.3 ±.012

PC board pattern (Bottom view)

Tolerance: ±0.1 ±.004

Schematic (Bottom view)

2 coil latching type only

7.62

.300

3-1.5 dia.

3-.059 dia.

4-2.0 dia.

4-.079 dia.

5.08

.200 17.78

.700

25.4

1.000

5.08

.200

5.08

.200

2 coil latching type1 coil latching type

---

Reset

coil

Set

coil

DQ-M (ADQM)

NOTES

1. Coil operating power

Pure DC current should be applied to the

coil. The wave form should be

rectangular. If it includes ripple, the ripple

factor should be less than 5%. However,

check it with the actual circuit since the

characteristics may be slightly different.

2. Coil connection

When connecting coils, refer to the wiring

diagram to prevent mis-operation or

malfunction.

3. Soldering and cleaning

1) When soldering the relays, ensure

conformance with the conditions listed

below.

[Automatic soldering]

(1) Preheating: less than 120°C 248°F

(solder target surface of terminal) for less

than 120 sec

(2) Soldering: less than 260±5°C

500±41°F (solder temperature) for less

than 6 sec (soldering time)

[Manual soldering]

(1) Soldering tip temperature: less than

350°C 662°F

(2) Soldering iron: 60 W to 100 W

(3) Soldering time: less than 3 sec

Furthermore, because the type of PC

board used and other factors may

inﬂuence the relays, test that the relays

function properly on the actual board on

which they are mounted.

2) This relay is not sealed. Do not wash it.

Also, make sure that any ﬂux overﬂowing

upward from the PC board does not get

inside the relay.

4. Others

1) If the relay has been dropped, the

appearance and characteristics should

always be checked before use.

2) The cycle lifetime is deﬁned under the

standard test condition speciﬁed in the

JIS C 5442-1996 standard (temperature

15 to 35°C 59 to 95°F, humidity 25 to

75%). Check this with the real device as it

is affected by coil driving circuit, load

type, activation frequency, activation

phase, ambient conditions and other

factors.

Also, be especially careful of loads such

as those listed below.

(1) When used for AC load-operating and

the operating phase is synchronous.

Rocking and fusing can easily occur due

to contact shifting.

(2) High-frequency load-operating

When high-frequency opening and

closing of the relay is performed with a

load that causes arcs at the contacts,

nitrogen and oxygen in the air is fused by

the arc energy and HNO3 is formed. This

can corrode metal materials.

Three countermeasures for these are

listed here.

1. Incorporate an arc-extinguishing

circuit.

2. Lower the operating frequency

3. Lower the ambient humidity

3) For secure operations, the voltage

applied to the coil should be nominal

voltage. In addition, please note that pick-

up and drop-out voltage will vary

according to the ambient temperature

and operation conditions.

4) Heat, smoke, and even a ﬁre may

occur if the relay is used in conditions

outside of the allowable ranges for the

coil ratings, contact ratings, operating

cycle lifetime, and other speciﬁcations.

Therefore, do not use the relay if these

ratings are exceeded. Also, make sure

that the relay is wired correctly.

5) Incorrect wiring may cause

unexpected events or the generation of

heat or ﬂames.

6) Check the ambient conditions when

storing or transporting the relays and

devices containing the relays. Freezing or

condensation may occur in the relay,

causing functional damage. Avoid

subjecting the relays to heavy loads, or

strong vibration and shocks.

7) The minimum switching capacity is

given as a guide to the lowest level that

switching is possible when using minute

loads. This value can change due to

switching frequency, environmental

conditions, and desired reliability level.

Therefore, please conduct sufﬁcient tests

under actual conditions.

8) Relays are shipped in a ‘reset’ state.

During shipping and handling, however,

shocks may change the state to ‘set.’

Consequently, at time of use (at power

on) it is recommended to ensure that

circuits are returned to the desired state

(‘set’ or ‘reset’).

9) Do not use parts that generate organic

silicon. When present in the vicinity,

conduction failure may occur.

10) This relay is designed to ﬂux-resistant

type. Malfunction and contact failure may

result if small insects get inside the relay.

11) Installation of M4 securing screw

Do not apply excessive pressure on the

terminals. This could adversely affect

relay performance. Secure to the PC

board a dummy terminal designed for

reinforcement of the terminal and use a

washer in order to prevent deformation.

Keep the installation torque to within 1.2

and 1.4 N·m (12 to 14 kgf·cm). Also, use

a spring washer to prevent it from

loosening. Do not use the dummy

terminals as wiring to the PC board. In

case wiring of the dummy terminals, the

conductor destruction may occur due to

the high current.

5. Usage, transport and storage

conditions

1) Ambient temperature, humidity, and

atmospheric pressure during usage,

transport, and storage of the relay:

(1) Temperature:

–40 to +70°C –40 to +158°F

(2) Humidity: 5 to 75% RH

(Avoid freezing and condensation.)

The humidity range varies with the

temperature. Use within the range

indicated in the graph below.

(3) Atmospheric pressure: 86 to 106 kPa

Temperature and humidity range for

usage, transport, and storage:

2) Condensation

Condensation forms when there is a

sudden change in temperature under

high temperature and high humidity

conditions. Condensation will cause

deterioration of the relay insulation.

3) Freezing

Condensation or other moisture may

freeze on the relay when the temperature

is lower than 0°C 32°F. This causes

problems such as sticking of movable

parts or operational time lags.

4) Low temperature, low humidity

environments

The plastic becomes brittle if the relay is

exposed to a low temperature, low

humidity environment for long periods of

time.

–40 0

–40 +32 +158

Te mperature, °C°F

Humidity, %RH

Tolerance range

(Avoid

condensation

when used at

temperatures higher

than 0°C32°F)

(Avoid freezing

when used at

temperatures

lower than

0°C32°F)