283
Amphenol Corporation Tel: 800-627-7100 www.amphenolrf.com
Assembly
CRIMP-CRIMP TYPES
Step 1
Step 2
Step 3
crimp here
Step 1 Strip cable jacket, braid, and dielectric to dimensions shown. All cuts
are to be sharp and square. Important: Do not nick braid, dielectric,
and center conductor. T inning of center conductor is not necessary if
contact is to be crimped. For solder method, tin center conductor
avoiding excessive heat.
Step 2 Slide outer ferrule onto cable as shown. Flare slightly end
of cable braid as shown to facilitate insertion of inner
ferrule. Important: Do not comb out braid.
Place contact on cable center conductor so it butts against
cable dielectric. Center conductor should be visible
through inspection hole in contact. Crimp or solder contact
in place as follows:
Crimp Method: Use Die Set Cavity for contact indicated in
table above.Solder Method: Soft solder contact to cable center
conductor. Do not get any solder on outside surface of
contact. Avoid excessive heat to prevent swelling of dielectric.
Step 3 Install cable assembly into body assembly so inner ferrule
portion slides under braid. Push cable assembly forward
until contact snaps into place in insulator. Slide outer ferrule over braid
and up against connector body. Crimp outer ferrule using Die Set
Cavity specified in table above.
outer ferrule contact body assembly
Amphenol Connector Cable Strip Dimensions, inches (mm) Hex Crimp Data
Number
Type RG-/U ab c
Cavity for Cavity for Die Set for CTL Series
Contact Outer Ferrule Tool 227-944‡ Tool No.
82-332 N Plug 9, 214 .531(13.5) .234(6.0) .140(3.5) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-340 N Plug 8, 213 .531(13.5) .234(6.0) .141(3.6) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-340-1052 N Plug B9913, 9914 .539(13.7) .250(6.4) .158(4.0) .116(2.9) .429(10.9) 227-1221-63 CTL-11
82-340-1054 N Plug LMR 400 .539(13.7) .250(6.4) .157(4.0) .116(2.9) .429(10.9) 227-1221-63 CTL-11
82-4425 N Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4425-1003 N Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4426 N Plug 8, 213 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4426-11RFX N Plug 8, 213, 214
Eth.Cables .630(16.0) .303(7.7) .157(4.0)
.100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4426-1001 N Plug
Ethernet Cables
.687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4426-1002 N Plug
Ethernet Cables
.687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4427 N Plug 142, 400 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-4427-1006 N Plug 142, 142B, 400 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-4440 N Angle Plug 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-4440-1001 N Angle Plug 9, 214, 225, 393 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .429(10.9) 227-1221-25 CTL-3
82-5370 N Plug 55, 142, 223 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5372 N Panel Jack 55, 141, 142 .600(15.2) .275(7.0) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5373
N Bulkh. Jack
55, 142, 223 .640(16.3) .315(8.0) .180(4.6) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5374 N Angle Plug 55, 142, 223 .687(17.4) .281(7.1) .187(4.7) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5375 N Plug 58, 141 .531(13.5) .233(5.9) .140(3.5) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5375-RFX N Plug 58, 141 .630(16.0) .303(7.7) .157(4.0) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5378 N Bulkh. Jack 58, 141 .640(16.3) .273(6.8) .180(4.6) .100(2.5) .213(5.4) 227-1221-57 CTL-3
82-5933 N Bulkh. Jack 316 .502(12.7) .102(2.6) .062(1.6) Solder .178(4.5) 227-1221-09 CTL-2
82-5988-1000 N Angle Plug 214, 393 .827(21.0) .492(12.5) .157(4.0) Solder .429(10.9) 227-1221-6001 CTL-3
82-5988-1004 N Angle Plug 214, 393 .827(21.0) .492(12.5) .157(4.0) Solder .429(10.9) 227-1221-6001 CTL-3
82-5993 N Plug LMR 600 .844(21.4) .344(8.7) .250(6.4) .176(4.5) .612(15.5) 227-1221-6001 —
82-5994 N Bulkh. Jack LMR 600 .844(21.4) .344(8.7) .250(6.4) .176(4.5) .612(15.5) 227-1221-6001 —
82-5995 N Angle Plug LMR 600 1.062(27.0) .562(14.3) .312(7.9) Solder .612(15.5) 227-1221-6001 —
82-6010 N Plug LMR 240 .610(15.5) .200(5.1) .200(5.1) Press-Fit .255(6.5) 227-1221-59,-13 CTL-1.5,8
82-6106 N Plug LMR 240 .687(17.4) .312(7.9) .187(4.7) .100(2.5) .255(6.5) 227-1221-59 CTL-5
82-5988-1000 N Angle Plug LMR 240 .827(21.0) .492(12.5) .157(4.0) .100(2.5) .255(6.5) 227-1221-59 CTL-5
82-5988-1004 N Angle Plug LMR 240 .827(21.0) .492(12.5) .157(4.0) .100(2.5) .255(6.5) 227-1221-59 CTL-5
STEP 3
AB
C
STEP 1
STEP 2
abc
Assembly Instructions-C11 Amphenol®
Type N
crimp here
